Electrical Interview questions Part 18

Electrical interview questions:Different between megger and contact resistance meter? Answers:Megger used to measure cable resistance, conductor continuity, phase identification where as contact resistance meter used to measure low resistance like relays ,contactors.

Electrical interview questions :When we connect the capacitor bank in series ? Answers:we connect capacitor bank in series to improve the voltage profile at the load end in transmission line there is considerable voltage drop along the transmission line due to impedance of the line. so in order to bring the voltage at the load terminals within its limits i.e (+ or - %6 )of the rated terminal voltage the capacitor bank is used in series

Electrical interview questions:What is Diversity factor in electrical installations? Answers:Diversity factor is the ratio of the sum of the individual maximum demands of the various subdivisions of a system, or part of a system, to the maximum demand of the whole system, or part of the system, under consideration. Diversity factor is usually more than one.

Electrical interview questions:Why field rheostat is kept in minimum position while armature rheostat at maximum position? Answers:In motors at the time of starting the armature resistance is introduced to reduce the high starting current and the field resistance is kept minimum torque. Electrical interview questions:Why humming sound occurred in h HT transmission line? Answers:This sound is coming due to ionization (breakdown of air into to have high starting

charged particles) of air around transmission conductor. This effect is called as Corona effect, and it is considered as power loss.

Electrical interview questions :what is rated speed? Answers:At the time of motor taking normal current (rated current)the speed of the motor is called rated speed. It is a speed at which any system take small current and give maximum efficiency.

Electrical interview questions:What is different between grounding and earthings? Answers:Grounding means connecting the neutral point of the load to the ground to carry the residual current in case of unbalanced conditions through the neutral to the ground whereas earthing is done in an electric equipment in order to protect he equipment in occurence of fault in the system. Electrical interview questions:Why should be the frequency is 50 hz only why not others like 45, 95 56 or anything , why should we maintain the frequency constant if so why it is only 50 ? Answers:We can have the frequency at any frequency you like, but than you must also make your own motors, transformers or any other equipment you want to use.We maintain the frequency at 50hz or 60hz cos the world maintains a standard at 50 /60hz and the equipments are are made to operate at these frequency.

Electrical Interview questions Part 17

Electrical interview questions:Which type of oil is used as a transformer oil? Answers:Transformer oil, or insulating oil, is usually a highly-refined mineral oil that is stable at high temperatures and has excellent electrical insulating properties. It is used in oil filled transformers, some types of high voltage capacitors, fluorescent lamp ballasts, and some types of high voltage switches and circuit breakers. Its functions are to insulate, suppress corona and arcing, and to serve as a coolant.

Well into the 1970s, polychlorinated biphenyls (PCB)s were often used as a dielectric

fluid since they are not flammable. They are toxic, and under incomplete combustion, can form highly toxic products such as furan. Starting in the early 1970s, concerns about the toxicity of PCBs have led to their banning in many countries. Today, non-toxic, stable silicon-based or fluoridated hydrocarbons are used, where the added expense of a fire-resistant liquid offsets additional building cost for a transformer vault. Combustion-resistant vegetable oil-based dielectric coolants and synthetic pentaerythritol tetra fatty acid (C7, C8) esters are also becoming increasingly common as alternatives to naphthenic mineral oil. Esters are non-toxic to aquatic life, readily biodegradable, and have a lower volatility and higher flash points than mineral oil. Electrical interview questions: If we give 2334 A, 540V on Primary side of 1.125 MVA step up transformer, then what will be the Secondary Current, If Secondary Voltage=11 KV? Answers :As we know the Voltage & current relation for transformer-V1/V2 = I2/I1 We By 540/11000= So,I2 = 114.5 Amps Electrical interview questions:what are the points to be consider for MCB(miniature circuit breaker selection?Answers:I(L)*1.25=I(MAX) are done on maximum maximum flow current. in Mcb circuit. specification current Know, VI= putting 540 V; V2=11KV these or 11000 V; I1= on 2334 Amps. RelationI2/2334 value

Electrical interview questions:what is the full form of KVAR? Answers:We know there are three types of power in Electricals as Active, apparent & reactive. So KVAR is stand for ``Kilo Volt Amps with Reactive component. Electrical Answer:Excitation in interview is applying questions:What an DC external voltage is to DC excitation? shunt coil motors.

Electrical interview questions:In three pin plug 6 Amp. 220v AC rating. why earth pin diameter is higher than ohter two pin? what its purpose ?

Answer:Because Current flow in the conductor is inversely proportional to the conductor diameter. So if any short circuits occur in the system first high currents bypassed in the Earthling terminal.( R=Pl/a area of the conductor increases resistance value decreases) Electrical interview question:What are Motor Generator Sets and explain the different ways the motor generator set can be used ? Answer:Motor Generator Sets are a combination of an electrical generator and an engine mounted together to form a single piece of equipment. Motor generator set is also referred to as a genset, or more commonly, a generatorThe motor generator set can used in the following different ways: 1.Alternating 3.DC at current 2.DC one voltage to DC (AC) to direct to at another current (DC) AC voltage

4.AC at one frequency to AC at another harmonically-related frequency Electrical interview question:What is power quality meter ?

Answer:Power Quality meters are common in many industrial environment. Small units are now available for home use as well. They give operators the ability to monitor the both perturbations on the power supply, as well as power used within a building, or by a single machine or appliance. In some situations, equipment function and operation is monitored and controlled from a remote location where communication is via modem, or high-speed communication lines.So we can understand the importance of power measurement through power quality meters.

Electrical interview question:What is the different between digital phase converter and ordinary phase converter? Answer:Digital phase converter are a recent development in phase converter technology that utilizes proprietary software in a powerful microprocessor to control solid state power switching components. This microprocessor, called a digital signal processor (DSP), monitors the phase conversion process, continually adjusting the input and output modules of the converter to maintain perfectly balanced three-phase power under all load conditions.

Electrical interview question:Explain the operation of variable frequency transformer? Answer:A variable frequency transformer is used to transmit electricity between two asynchronous alternating current domains. A variable frequency transformer is a doubly-fed electric machine resembling a vertical shaft hydroelectric generator with a three-phase wound rotor, connected by slip rings to one external ac power circuit. A direct-current torque motor is mounted on the same shaft. Changing the direction of torque applied to the shaft changes the direction of power flow; with no applied torque, the shaft rotates due to the difference in frequency between the networks connected to the rotor and stator.The variable frequency transformer behaves as a continuously adjustable phase-shifting transformer. It allows control of the power flow between two networks .

Electrical interview question:What is the main use of rotary phase converter ? Answer:Rotary phase converter will be converting single phase power into true balanced 3 phase power,so it is often called as single phase to three phase converter .Often the advantages of 3 phase motors, and other 3 phase equipment, make it worthwhile to convert single phase to 3 phase so that small and large consumers need not want to pay for the extra cost of a 3 phase service but may still wish to use 3 phase equipment.

Electrical Interview questions Part 15

Electrical interview question:Why most of analog o/p devices having o/p range 4 to 20 mA and not 0 to 20 mA ? Answer:4-20 mA is a standard range used to indicate measured values for any process. The reason that 4ma is chosen instead of 0 mA is for fail safe operation .For example- a pressure instrument gives output 4mA to indicate 0 psi, up to 20 mA to indicate 100 psi, or full scale. Due to any problem in instrument (i.e) broken wire, its output reduces to 0 mA. So if range is 0-20 mA then we can differentiate whether it is due to broken wire or due to 0 psi.

Electrical interview question:Two bulbs of 100w and 40w respectively connected in series across a 230v supply which bulb will glow bright and why?

Answer:Since two bulbs are in series they will get equal amount of electrical current but as the supply voltage is constant across the bulb(P=V^2/R).So the resistance of 40W bulb is greater and voltage across 40W is more (V=IR) so 40W bulb will glow brighter.

Electrical interview question:What is meant by knee point voltage? Answer:Knee point voltage is calculated for electrical Current transformers and is very important factor to choose a CT. It is the voltage at which a CT gets saturated.(CT-current transformer).

Electrical interview question:What is reverse power relay? Answer:Reverse Power flow relay are used in generating stations's protection. A generating stations is supposed to fed power to the grid and in case generating units are off,there is no generation in the plant then plant may take power from grid. To stop the flow of power from grid to generator we use reverse power relay.

Electrical interview question:What will happen if DC supply is given on the primary of a transformer? Answer:Mainly transformer has high inductance and low resistance.In case of DC supply there is no inductance ,only resistance will act in the electrical circuit. So high electrical current will flow through primary side of the transformer.So for this reason coil and insulation will burn out.

Electrical interview question:What is the difference between isolators and electrical circuit breakers? What is bus-bar?

Answer:Isolators are mainly for switching purpose under normal conditions but they cannot operate in fault conditions .Actually they used for isolating the CBs for maintenance. Whereas CB gets activated under fault conditions according to the fault detected.Bus bar is nothing but a junction where the power is getting distributed for independent loads.

Electrical interview question:What are the advantage of free wheeling diode in a Full Wave rectifier?

Answer:It reduces the harmonics and it also reduces sparking and arching across the mechanical switch so that it reduces the voltage spike seen in a inductive load