Class D Amplifier Design Basics II

02/19/2009 Rev 1.0

Contents
Chapter 1
Getting Familiar with Class D Audio Amplifier

Chapter 2
Latest Class D Audio Amplifier Technology Trend

Chapter 3
Identifying Problems ~ Performance Measurement of Class D Amplifier

Chapter 4
Reducing Distortion ~Dead-time ~ LPF Designs

Chapter 5
Reducing Noise ~ Isolation Technique ~ PCB Design

APPENDIX
Simulation of a Simple Class D Amplifier

Chapter 1: Getting Familiar with Class D Audio Amplifier

Audio Amplifier Market Trend

More Channels Smaller Box Lighter Weight
A Wire with Gain More Functions

(Digital Input, Diag)

Device Technology

Smaller Size Lower Cost Control Technology Audio Performance

Why Class D Now?

Audio Market Trend

Class AB

More Channels Smaller Size

Smaller Size
IR Class D

Higher Performance
Device Technology
MOSFET High Speed HVIC

Basic Concept of Class D Audio Amplifier

COMP

Class D Switching Stage

LPF

Analog signal

PWM

Amplify

PWM

Analog signal

VOUT = B (2D-1) In concept, Class D amplifier is linear; i.e. 0% distortion. 6

PWM: Heart of Class D Operation

Audio signal PWM PWM Audio signal

10 5 0 -5 -10 60 Time/uSecs 80 100 120 140 20uSecs/div V V

10 5 0 -5 -10 60 Time/uSecs 80 100 120 140 20uSecs/div

Class AB vs. D Energy Point of View

Similar to a variable resistor

Class AB
PLOSS depends on output power factor Similar to a transformer with variable turn ratio

IIN = IOUT

Class D

VIN x IIN = VOUT x IOUT Note that input current and output current are not equal.

Bi-directional energy flow

Class AB vs. D Characteristic Comparison (1/2)

Feature Class D Advantage
Superior efficiency Efficiency can be improved with device technology Efficiency Suitable to drive lower impedance load Can drive reactive load without significant degradation of efficiency Requires smaller power supply Bi-directional energy flow; any energy reflected from the load is recycled to the power supply. Suitable to drive highly reactive load, such as woofer, speaker system with dividing network, piezo speaker, etc.

Class AB
Efficiency is fixed. Extremely inefficient when driving lower impedance load. Extremely inefficient when driving reactive load.

Energy flow

Drivability

All the reflected energy from reactive components and back EMF are consumed dissipating heat The output device has high impedance, ~tens of k ohm. Inherently has low output impedance (m ohm range) With a strong voltage feedback, Class AB can achieve low output impedance. Power supply current = load current. For a given output Lower impedance loading does not burden power supply. power with decreased load (Power supply current) (load current). impedance, the supply current and heat dissipation in the output device increase. Cross conduction limits high Wide power bandwidth; no extra effort to drive high frequency rated power. frequency power bandwidth.

Class AB vs. D Characteristic Comparison (2/2)

Feature Class D Advantage
Topology is inherently linear without feedback Linearity Cross over distortion is not in zero crossing area Output device is non-linear; exponential in BJT, quadratic in MOSFET. Strong feedback is necessary to achieve good linearity. Cross over distortion is at where load current crosses zero, which is most critical point of operation. Output devices in linear operating mode has strong temperature coefficient in gain. Loop-gain is changing dynamically with output power. Because of strong non-linearity in device and 'exposed' feedback node, weak to RF noise.

Class AB

Stability

Thermally stable; gain of the Class D stage, bandwidth, loop-gain are independent of output device temperature. No bias-current thermal compensation

Noise immunity

Inherently immune to incoming noise; low drive impedance, inductor between the load and amplifier. Higher reliability from less heat. Less metal fatigue in solder joints.

Reliability

10

Class AB vs D Comparison
Loss in Class AB
Pc = 0.2

Loss
VCC 8 RL
2

1 Vcc (1 K sin t ) Vcc K sin t d t PC = 2 0 2 2 RL

Vcc 2 = 8 RL

2K K 2 2

Note that this is independent to device parameters.

Loss

K=2/

K=1

Loss in Class D

PTOTAL = Psw + Pcond + Pgd

Pcond = RDS (ON ) RL Po
2

Efficiency can be improved further!

Pgd = 2 Qg Vgs f PWM

K=1
K is a ratio of Vbus and output voltage.

Psw = COSS VBUS f PWM

To learn more about power losses in Class D, refer to AN-1070 Class D Amplifier Performance Relationship to MOSFET Parameters.

11

Practical Class D Amplifier

Perturbation Supply impedance Bus Pumping Nonlinear inductance / Capacitance DC Resistance

Limited Gain & BW Noise Figure

+VCC

Audio source

PWM
F/B

Gate Driver

-VCC

1. Non-linearity in the switching stage due to timing errors added, such as dead-time, ton/toff, and tr/tf 2. Limited amount of error collection capability due to limited gain and bandwidth in PWM modulator 3. Audio frequency band noise added in PWM modulator 4. Unwanted characteristics in the switching devices, such as finite ON resistance, finite switching speed or body diode characteristics. 5. Parasitic components that cause ringing on transient edges 6. Power supply voltage fluctuations due to its finite output impedance and reactive power flowing through the DC bus 7. Non-linearity in the output LPF.

Dead-time

Finite RDS(on) Vth and Qg Body diode recovery Stray inductances

RDS(ON)

ON delay

OFF delay

Note that 0.01% of nonlinearity corresponds to10mV out of 100V DC bus, or 0.25ns in 400kHz!

Finite dV/dt

12

MOSFET Basics
A MOSFET is a device to switch electronic current. A driving MOSFET charges/discharges a capacitor (Gate to Source, Gate to Drain). A MOSFET does not require any energy to keep it on-state. In switching transition, stray impedance in each terminal slows down switching and generates unwanted rings.

To learn more about power MOSFETs, refer to AN-1084 Power MOSFET Basics.

13

Driving MOSFET for PWM

Only one side, either high-side or lowside, MOSFET is ON at a time. side and low-side MOSFETs determines the output voltage.
High-side ON

The ratio of ON time between the high-

Driving a high-side MOSFET

A floating power supply that referenced

Alternating at Switching Frequency

to switching node drives the gate of the high-side MOSFET when the low-side MOSFET is ON. (Bootstrap power supply)

The floating power supply is charged

Low-side ON

Driving a low-side MOSFET

A bias voltage that refers to negative

bus voltage B drives the gate of the low-side MOSFET.

NOTE: In a practical design, a dead-time where both high- and low-side MOSFETs are off is inserted to prevent simultaneous ON state. Refer to chapter 4 for more details.

14

Bootstrap High Side Power Supply

High-side ON

I4 turns off the low-side MOSFET. Then, I5 turns on the high-side MOSFET, lifting VS up to +B. As long as the high side is ON, bootstrap diode DBS isolates the floating power supply VBS and bootstrap capacitor CBS retains VBS voltage. After the high-side MOSFET ON state, I1 turns off the high-side MOSFET, then I2 turns on the low side MOSFET. As soon as switching node VS reaches negative supply B, the bootstrap diode DBS turns on and starts charging bootstrap capacitor CBS with current I3 from VCC. Note that VBS = VCC (forward drop voltage of DBS).

Low-side ON

15

Example of a 100W Class D Amplifier

VAA supply

Optional switching noise filter Feedback resistor

High-side OCP Input resistor Startup resister Bootstrap floating supply charging path

6V

DC blocking capacitor

ENABLE

20 V

6V

C11 10 F

R8 4.7

Bootstrap floating supply capacitor Demodulation LPF

2nd order integrator

VSS supply

20 V

Low-side OCP

Dead-time

16

Chapter 2: Latest Class D Audio Amplifier Technology Trend

Class D Amplifier Innovations

Device Technologies

Packaging Technology

Signal Processing Technologies

MOSFET FOM (Figure of Merit) improvements Higher voltage capability Faster and accurate switching time High gain low noise process High GBW (Gain BandWidth) process

Smaller Low stray inductance Surface mount Dual sided cooling Hybrid module Multi chip module

Feedback techniques Self-oscillating topologies Digital domain PWM processing

Higher Performance + Smaller Size + Lower Cost At The Same Time !

18

1. MOSFET Technology Trend

A MOSFET has inherent trade-offs between ON resistance and gate charge, RDS(on) vs Qg. In device design, this translates into Conduction loss vs Switching loss trade-off. The objective of optimization for Class D applications is to achieve minimal power loss. Newer platforms show better FOM (Figure of Merit) This is what makes Class D keep improving!
Normalized R*Qg

International Rectifier Mosfet R*Qg Trend

1.2 Planar Stripe Technology 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 2000

IR Mosfet Technology Constant Improvement

Trench Technology

2001

2002 Fiscal Year

2003

2004

2005

19

MOSFET Evolution
The latest trench MOSFET technology shows 7 times better figure of merit.

Higher cell density

Planar MOSFET Structure

IRF540 100 V 66m ohms 50 nC
RDS(on) x Qg=3300

Trench MOSFET Structure

IRF6665 100 V 53m ohms 8.4 nC
RDS(on) x Qg=445

20

Trade-offs in MOSFET Design

There is a best die size for a given output power. Optimum die size for minimal PLOSS depends on load impedance, rated power and switching frequency. A more advanced platform with better FOM acheives lower PLOSS.

Optimal MOSFET die size Optimal MOSFET Parameters Total Loss = Conduction Loss + Switching Loss

Total Loss

Optimal MOSFET Die Size

Conduction Loss

Switching Loss

To learn more about MOSFET selection, refer to AN-1070 Class D Amplifier Performance Relationship to MOSFET Parameters.

21

Importance of Packaging
How the package affects the design? 1. Amplifier size Increase efficiency Increase current capability Improve the MOSFET thermal efficiency 2. EMI considerations Better control of current and voltage transients 3. Amplifier linearity Decrease switching times Narrow the MOSFET parameter distribution 22 To utilize benefits from a newer generation MOSFET, new package with reduced stray inductance is necessary.

D2/S1

G1

TO-220 Full-Pak 5 PIN

G2

S2

D1

Stray Inductance

A MOSFET has capacitive elements. Stray inductance is where excessive energy is stored, causing over/under shoots and rings. Stray inductance in Source returns feedback voltage to gate, slowing down switching speed significantly. The smaller the parasitic components the better performance!

To learn more about MOSFET switching behavior, refer to AN-947 Understanding HEXFET Switching Performance.

23

Package Comparison

Lower inductance at frequency than SO-8, D-Pak, MLP and D-Pak TO-220 inductance package is ~ 12nH DirectFET is 0.4nH 24

EMI Comparison
DirectFET amplifier shows better EMI performance than TO-220 amplifier Over 2MHz, DirectFET amplifier shows approximately 9dBuV lower Peak,
Quasi-Peak and Average noise than TO-220 amplifier

Both PCBs meet audio amplifier EMI standards limits (CISPR13) DirectFET
Frequency (MHz)

TO-220 (w/DirectFET die)

Frequency (MHz)

CISPR13 Quasi-Peak Limits Average Limits

CISPR13 Quasi-Peak Limits Average Limits

25

2: Gate Driver IC Technology Trend

More integration to realize smaller footprint
Analog signal processing Level shifting
Feed back

Gate driving Power switching

AUDIO SIGNAL

PWM Level Shift Down Level Shift Up Dead Time Shut Down
Speaker

Over Current Protection Control Logic

Protection functions

26

What The Gate Driver IC Does?

Four Essential Functions in Gate Driver IC

Level Shift Deadtime Generation

Gate Drive Under Voltage Lockout

Gate Driver IC

To learn more about High Voltage Gate Driver IC, refer to AN-978 HV Floating MOS-Gate Driver ICs.

27

How Internal High Voltage Level Shifter Works

Operation Principle A pair of SET and RESET signals are generated at the PULSE GEN block. The SET and RESET pulses drive the high voltage MOSFET to send these signals to circuitries in a floating highside well.
Pulse Gen Waveform Example
HIN

The high-side circuitry reconstructs PWM from SET and RESET pulses. This method minimizes power dissipation in the high voltage MOSFETs in level shifter. 28

SET

RESET

HO

Floating Well and Noise Isolation

INPUT SECTION

HIGH SIDE GATE DRIVE

LOW SIDE GATE DRIVE LEVEL SHIFTERS Translate PWM signal to different voltage potential Isolate circuit blocks that are in different voltage potentials Note Level shifter rates supply voltage ranges Level shifting is useful to drive high-side the MOSFET whose source is tied to switching node. Level shifting blocks switching noise coming into sensitive input section.

29

Dead-time Generation
With Dead-time

Dead-time (or blanking time) is a period of time intentionally inserted in between the ON states of high- and low-side MOSFETs. This is necessary because the MOSFET is a capacitive load to the gate driver that delays switching time and causes simultaneous ON.
NO DEADTIME

Without Dead-time
INPUT

Lack of dead-time results in lower efficiency, excessive heat and potential thermal failure. Usually, dead-time is realized by delaying turn on timing.

HIGH-SIDE

LOW-SIDE

SIMULTANEOUS ON

30

Under Voltage Lockout

Under voltage lockout (UVLO) prevents the MOSFET from entering the half-ON region when the gate bias voltage is reduced. The half-ON condition of the MOSFET creates excessive power loss due to increased RDS(on) that could lead to MOSFET failure, therefore must be avoided.
UV DETECT

During the UVLO, gate drive stage keeps HO/LO low in order to prevent unintentional turn-on of the MOSFETs. UVLO in VCC resets shutdown logic and causes CSD recycling to start over the power up sequence. The IR Class D audio gate driver family is designed to accept any power sequence.

CSH VB

HIGH SIDE CS

UV Q

HO

HV LEVEL SHIFT

FLOATING HIGH SIDE

HV LEVEL SHIFT

VS

UVLO of VBS shuts down HO and disable high-side current sensing

31

Inside of High Voltage Gate Driver IRS2092

High Voltage Isolation

FLOATING INPUT

OTA
ENABLE

GND

PWM MODULATOR HV LEVEL SHIFT UV DETECT

20.4V

PWM Modulation Pop Noise Elimination

VAA
6.5V

CLICK NOISE ELLIMINATION

UV DETECT

CSH VB

IN-

VAA+VSS 2

HIGH SIDE CS

UV Q

COMP

HO

COMP
6.5V

HV LEVEL SHIFT

FLOATING HIGH SIDE

HV LEVEL SHIFT

5V REG UV DETECT

VSS

High Speed, Low Distortion VCC Level Shift

VS

DEAD TIME

Shut down Recycle Control

CSD
20.4V CHARGE / DISCHARGE SD DT

LO
HV LEVEL SHIFT PROTECTION CONTROL HV LEVEL SHIFT

Dead Time Control

COM

LOW SIDE CS

Over Current Sensing OCSET

VREF DT

32

3. PWM and Feedback Technologies

PWM modulators functions Convert analog or digital audio signal (PCM) to PWM that has reasonable switching frequency for power MOSFET Error corrections to improve audio performance Demands

Feedback to reduce DC offset,

distortion and noise floor

Larger loop gain for lower distortion,

higher power supply rejection ratio (PSRR) damping factor reduced EMI

Post filter feedback for higher Switching frequency control for

33

Natural PWM vs. Self Oscillating PWM

Natural PWM
Open loop or closed loop Fixed frequency

Optional feedback

Self-oscillating PWM
Closed loop Frequency changes with modulation High loop gain Fewer components

34

Modern PWM Topologies

Self-oscillating PWM with 2nd order integration

Self-oscillating PWM with pulse width control

Global feedback from speaker output

Inductor-less PWM

35

IRAUDAMP5 Functional Block Diagram

Typical IR audio evaluation board based on self-oscillating PWM with 2nd order integration *
FEEDBACK VOLUME IC CS3310 INPUT

IRF6645 DirectFET
ERROR AMP +

+
PWM COMP.

L /S DT SD

L/S

LPF

*
CS

Micro controller

OTP

DCP

IRS2092

PROTECTION LOGIC

PROTECTION CONTROL

36

Chapter 3: Identifying Problems ~ Performance Measurement of Class D Amplifier

Identifying Problems
Proper audio performance measurement is crucial to identify potential
problems.

Frequency response and THD+N are the minimum basic measure of audio
performance.

Problem Low frequency response High frequency response High harmonic distortion High noise floor

Possible Causes Audio input, feedback network Audio input, feedback network, LPF design Shoot-through, dead-time, switching noise coupling Analog input, switching noise coupling

38

1. Frequency Response
Use resistive dummy load. Set reference voltage level to 1W output power at 1kHz. Sweep sinusoidal signal from 20Hz to 100kHz. Take frequency response with various load impedances and without
loading.
International Rectifier
+1 +0.5 +0 -0.5 -1 -1.5

A-A FREQUENCY RESPONSE

08/15/06 10:56:54

d B r A

Reference 1kHz=0dB, usually set to 1W output power

-2 -2.5 -3 20

50

100

200

500

1k Hz

2k

5k

10k

20k

50k

100k

Sweep 1

Trace 1

Color Red

Line Style Solid

Thick 1

Data Anlr.Level A

Axis Left

Comment 8Ohm, 1W, 80kHz BW

Frequency Response from 20k to 20 Hz. F4 first to set 0 dBr at 1kHz. The 2 Ch Ampl Function Reading meter BW is set to <10 Hz & >500kHz so the bandwidth is the same as the Level meter. Optimize for detail. A-A FREQ RESP.at2

39

Check for..

R117 3.3k 1w R17 R22 10K U1 75k R18 9.6k R19 10k CP6 GND INCOMP CSD VSS VREF OCSET IRS2092S DIP VB HO VS VCC LO COM DT 5 2 3 1nF 1nF C6 5 10uF 6 CP2 22uF R118 3.3k 1w R13 10k 8 R12 8.7k 9 R26 10k R27 10k CP5 22uF VCC 7 11 -B 10 R21 10R R23 4.7K 12 D3 R20 4.7R 20R R25 LED1 Blue C14 0.1uF CP7 470uF,100V 1 2 -B C13 0.1uF, 400V C7 1nF 4 15 22uF 14 VS1 13 20R R24 3 C12 0.47uF, 400V R30 R31 10, 1W 2.2k 4 D4 C11 0.1uF,100V FET1 CP8 470uF,100V +B

Low Frequency
RCA1 CP1 10uF R2 3.3k

CP4 1 R8 100k R11 270R 22uF VAA CSH 16

High Frequency
L1 22uH CH_OUT SPKR1 1 2

R3 SD D1 100R CP3

C4

+ CH1 -

-B

40

2: THD+N
THD+N is a sum of harmonic distortion components and noise, i.e. anything except fundamental spectrum. THD is a measure of linearity. Refer to Chapter 4 Noise is a measure of added errors not depending on the input signal Refer to Chapter 5
Fundamental

Fundamental

THD
3rd order harmonic

2nd order harmonic

frequency

THD+N
3rd order harmonic Noise

2nd order harmonic

frequency

41

What is Distortion?
THD is a simple way to measure non-linearity of the amplifier. If the amplifier is not linear, it generates harmonics.
Any repetitive waveforms can be expressed as a sum of sinusoidal signal as

Harmonic distortion is a ratio of rms value of the harmonic component and the original waveform. Total harmonic distortion is a ratio of rms value of sum of the all harmonic component and the original waveform.

42

How to Read THD+N vs. Power

100
T

IRAUDAMP4 THD+N
10

30 V

THD+N vs. Power spells

out noise floor, distortion and output power in a shot.

1 % 0.1

25 V 35 V

Noise floor dominant part

has 20dB/dec slope.

0.01

Reading above noise floor

slope is dominated by harmonic distortion.
200m 500m 1 2 W 5 10 20 50 100 200

0.001 100m

To trouble shoot, better to

start with single channel operation.

Noise floor

Distortion

Clipping

43

Check for..

R117 3.3k 1w R17 R22 10K U1 CP4 1 R8 100k VAA GND INCOMP CSD VSS VREF OCSET IRS2092S DIP CSH VB HO VS VCC LO COM DT 16 15 22uF 3 1nF 1nF C6 5 10uF 6 CP2 22uF R118 3.3k 1w R13 10k 8 R12 8.7k 9 R26 10k R27 10k CP5 22uF VCC 7 11 -B 10 R21 10R R23 4.7K 12 D3 R20 4.7R 20R R25 LED1 Blue C14 0.1uF CP7 470uF,100V 1 2 -B C13 0.1uF, 400V C7 1nF 4 14 VS1 13 20R R24 3 C12 0.47uF, 400V R30 R31 10, 1W 2.2k 4 75k R18 9.6k R19 10k CP6 2 D4 C11 0.1uF,100V FET1 5 CP8 470uF,100V +B

Ceramic?
RCA1 CP1 10uF R2 3.3k

dead-time

R11 270R

22uF

LPF
L1 22uH CH_OUT SPKR1 1 2

R3 SD D1 100R CP3

C4

+ CH1 -

-B

Switching noise coupling

44

Audio Measurement Setup

Amplifier Output

20KHz LPF

Amplifier Output Filtered

Amplifier Input

For more information on Class D audio measurement, refer to white paper, Measuring Switch-mode Power Amplifiers by Bruce Hofer, from //ap.com

45

Audio Measurement Setup with IRAUDAMP7D

Audio Precision System Two with AES-17 Filter

46

AP Substitute
Old audio analyzers are not designed to
tolerate high frequency noise that is from carrier signal residual from a Class D amplifier.

Place a 3rd order LPF to remove the

switching carrier ingredients in front of the audio analyzer changing scaling range manually

Check measurements are correct by

An Example of an additional pre-LPF for HP8903B

470 R1 8 R4 680 R2 1K R3

4.7n C1

2.2n C2

1n C3

To HP8903B Dummy Load

47

Chapter 4: Reducing Distortion ~dead-time ~ LPF Designs

Trade-off 1: Dead-time and Distortion

34 40

30

20

1 Positive half cycle: Hard Switching 2 4 Cross over region: ZVS

10

Vout( t )

10

20

30 34 40 0 0

3 Negative half cycle: Hard Switching

5 .10
4

0.001 t

0.0015

0.002 0.0021

Dead-time reduces volt-second therefore voltage gain. There is a region that dead-time does not affect around zero crossing (regions 2 and 4). The smaller the dead-time, the lower the distortion. Too narrow dead-time could cause shoot-through from unit-to-unit, temperature and production variations, that could seriously affect product reliability. Audio performance and reliability is NOT a trade-off. 49

Gate Drive and Switching Output

ZVS Region Turning off of the previous MOSFET dictates transition in switching waveform. Hard Switching Region Turning on dictates output switching waveform.

High-side VGS

Low-side VGS

Switching Node VS

50

PWM Switching Cycle

1 High Side ON
+B
VBS +B

VCC

-B

4 Dead-time
?
VBS +B

2 Dead-time
?
VBS +B

VCC

-B

VCC

-B

-B
VBS

+B

VCC

-B

3 Low Side ON 51

During Dead-time
Polarity of IL is always toward the load VS follows high side switch status Polarity of IL alternates VS follows turning off edges of both high and low sides ZVS No influence from dead-time insertion Polarity of IL is always toward the amp VS follows low side switch status

2 4

Note: Dead-time insertion reduces volt-second of VS. Dead-time inserted in the rising edge of the high side affects the operating region 1. Dead-time inserted in the rising edge of the low side affects the operating region 3. As a result, output voltage gets lower than it should be, causing non-linearity in the output stage.

52

Trade-off 2: Inductor and Distortion

The quality of the output inductor
is crucial to achieve not only the target audio performance but also efficiency.
THD characteristic with various inductors
100 T TTTT TT T 10

Inductance changes with load

current, which causes distortion.

0.1

0.01

Core saturation increase inductor

ripple significantly that can trigger over current protection.
Inductance

0.001

0.0001 100m 200m 500m 1 2 5 W 10 20 50 100 200

Soft saturation core Hard saturation core Load current

Frequency characteristic of IRAUDAMP4

53

LPF Design
Set corner frequency according to
the bandwidth requirement.
Inductance and inductor ripple

Design LC-LPF with Q=0.7 for a

nominal load impedance to attain flat frequency response. Note that - The higher the corner frequency the higher the switching carrier leakage - The lower the corner frequency the bigger the inductance size

I L PP =

Vbus L f SW

Inductor ripple current dictates ZVS region

Lower Switching Frequency

Higher Ripple Current Higher Corner Frequency

Higher Ripple Current

54

LPF Design
1. Decide the order of the filter based on the attenuation of the switching frequency given by:
f 2 N At = 10 log 1 + fC

2nd order LPF

3rd order LPF

4th order LPF

2. Design Butterworth filter

# of Order Lk1 Ck1 Lk2 Ck2

Ln = Cn =

RL Lk n 2 fC Ck n 2 f C RL

1.414214

0.707107

1.5000

1.3333

0.5000

1.530734

1.577161

1.082392

0.382683

3. Design Zobel network

55

Choosing Inductor for LPF

Air Coil Large, High DCR, Low distortion, Leakage flux

Drum Core (Ferrite, Open Circuit)

Small, Leakage Flux, Low DCR

Drum Core (Ferrite, Closed Circuit)

Small, Hard saturation, Low DCR

Toroidal Core (Iron Powder)

Soft saturation, Lower iron loss

NOTE Ferrite core is suitable for smaller size Iron powder is suitable for high power

Determine IRMS rating for temperature rise condition with 1/8 rated power Determine peak current (ISAT) based on maximum load current

56

Choosing Capacitor for LPF

Polyester film, winding Small, High ESR

Ceramic

High dielectric type has large distortion, lower AC ratings

Polyester, non-inductive

Small, lower AC voltage rating

Polypropylene, non-inductive

Low dissipation factor, large size, low distortion

NOTE Do not use winding structure types. Use stacked structure. Check AC voltage ratings at highest audio frequency.

57

LPF Design Example

+ 4 + 2 + d 0 B r 2 4 6

Corner frequency: 40kHz Load impedance: 4 ohms Output power: 250W (32Vrms, 11Apeak)
22uH

8 4

8 10 2 0 5 0 10 0 20 0 50 0 1 2 k Hz k 5 k 10 k 20 k 50 k 200 k

0.1uF 0.47uF 10

Sagami 7G17B220 22H, 13A, 10m Ferrite, closed circuit with inner gap

EPCOS B32652A4474J Polypropylene, 0.47F, 400VDC

58

Chapter 5: Reducing Noise ~ Noise Isolation Technique ~ PCB Design

Sources of Noise in Class D Amplifier

Switching noise Switching noise is generated by the output MOSFET switching in wide range of frequency spectrum above the audible range. The amount of switching noise depends on: Switching speed Size of the MOSFET Load current PCB layout Locations and quality of bypass capacitors Audio noise Audio noise is a noise ingredient in audible frequency range in the speaker output. Major causes of audio noise includes: Noise figure (NF) in the front-end error amplifier Jitter in switching time RFI noise from switching noise injection Thermal noise from resistors Hum noise (AC line 60Hz and its harmonics) from ground loop

60

Noise Reduction Strategy

1. Minimize noise source in switching stage

2. Maximize noise immunity in analog stage

3. Minimizing noise coupling from switching stage to analog stage

61

1: Minimizing Noise Source

Self-commutation at idling. If rings, check for shoot-through, check dead time. Reverse recovery charge, Qrr, causes hard switching that triggers resonance in stray reactance. Qrr is a function of di/dt, drain current and die temperature. Slower switching helps to reduce Qrr. Stray inductance is where excessive energy is stored. Look for optimum trace layouts to minimize stray inductance. Careful component selection is key to minimize stray reactance.
Low dV/dt driven by inductor and Coss High dV/dt driven by MOSFET turn on

Idling (ZVS)

Hard-switching
Rings triggered by Qrr

62

Reducing Noise with RC Snubber

RC voltage snubber is used to suppress voltage spikes in switching and power supply nodes. Resistor in RC snubber absorbs energy from reactance by damping resonance. To maximize effectiveness of a snubber - Resistance should be close to impedance of resonant element. - Capacitance should be larger than resonant capacitor. - Capacitance should be small enough not to cause too much dissipation in the resistor. Power dissipation from the resistor P= 2*f*(CV2)

63

Snubber and THD

Adding snubber usually improves THD+N. Change should be in hard switching region. Basic approach: Make all efforts to minimize stray inductances and current loop areas (minimize resonant energy), then tailor snubber values. Pay attention to dissipation at snubber.
% 0.02 0.01 0.005

1 0.5

0.2 0.1 0.05

0.002 0.001 100m

200m

500m

5 W

10

20

50

100

300

Sweep 1 2

Trace 1 1

Color Red Blue

Line Style Solid Solid

Thick 2 2

Data Anlr.THD+N Ratio Anlr.THD+N Ratio

Axis Left Left

Comment original+150p+10ohighside original (low side snubber onl

64

2: Maximizing Noise Immunity

NOTE Ground can be a route of noise injection to error amplifier

Input RF Filter Filter out HF noise and reduce node impedance at high frequency Differential Input RFI Filter Prevent RFI causing audio frequency interferences from switching rings

Feedback LPF Weed out high frequency spectrum to avoid TIM distortion in the error amplifier

65

RFI
Analog stage uses non-linear components such as diode, BJT and FET. When a non-linear component receives high frequency components, it detects envelop information that could fall into audio frequency range (amplitude modulation envelop detector). When non-linear components receives high frequency components along with audio signal, it could shift operating bias point and cause distortion in audio signal.
Diode amplitude detector

66

3: Minimizing Noise Coupling

There are functional blocks that generate noise. There are functional blocks that are sensitive to noise. The PCB designer should identify them and find out the best combination of the placement based on these facts and mechanical and thermal requirements. Noise sensitive functions: - The audio input circuitry - The PWM control circuitry - Noise generating functions - The gate driver stage - The switching stage
Noise Generating Nodes

Noise Sensitive Nodes

67

Switching Noise Injection Example

Noise Coupling from VS Insufficient Bypass Cap Original Design (IRAUDAMP7D)

68

PCB Design Tips

The first and most important step for PCB designers is to group components dedicated to a common purpose, such as: - the audio input circuitry - the PWM control circuitry - the gate driver stage - the switching stage By identifying which components belong together, place the remaining circuitry by coupling them appropriately into open areas of the board.

Key Components Layout Example (IRAUDAMP7D)

PWM

GATE DRIVE

MOSFET

LPF

Placement Determines Maximum Performance !

69

PCB Layout Example

Audio Input, Error Amplifier

Note that Separation between analog and switching sections Minimized trace impedances with planes in power section No overlap between switching nodes and analog nodes

Analog Section

Gate Drive Section

Switching Nodes

Load Current Paths

Power Section 70

APPENDIX

Simulation of a Simple Class D Amplifier (SIMetrix)

Feedback
47k R1 1n C1 220 R2 10k 2.5*(1+tanh(1e4*v(n1,n2))) ARB1 DELAY N1 OUT ARB1-OUT N2 1n C2 E2-N 10u C8 3.3k R8

0 IC

HC04D U5 250n U1

HC04D HO U2 LO S1 D3 IDEAL 50 V4

AC 1 0 Sine(0 1 5k 0 0) V5

E3

18u L1 S2 470n C3 D4 IDEAL 4 R6 sp out

Integrator

Comparator

Delay

Gate Driver

Note Disable initial DC operating point analysis Add initial value in the feedback loop to start off oscillation Get into further work once basic ideal model is confirmed
MOSFET

LPF
50 V1

Simulation set up with SIMetrix

Trial version of SIMetrix can be downloaded from: http://www.catena.uk.com/

72

Simulation Result Example

100

80

Switching Node

60

40

20

Gate and other internal nodes

-20

Speaker Output

-40 150 T im e / S e c s 200 250 300 350 400 450 5 0 S e c s / d iv

73

END

February 19, 2009