INTRODUCTION TO FX POSITIONING CONTROL SYSTEMS

FX SERIES PROGRAMMABLE CONTROLLERS

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

FX Series Programmable Controllers

INTRODUCTION TO FX POSITIONING CONTROL SYSTEMS

Foreword
This document contains text, diagrams and explanations to guide the reader in understanding positioning control. Store this document in a safe place so that you can take it out and read it whenever necessary.
This document confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this document.

2007 MITSUBISHI ELECTRIC CORPORATION

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

Outline Precautions
This document provides information for the use of the FX Series Programmable Controllers. The document has been written to be used by trained and competent personnel. The definition of such a person or persons is as follows: 1) Any engineer who is responsible for the planning, design and construction of automatic equipment using the product associated with this document should be of a competent nature, trained and qualified to the local and national standards required to fulfill that role. These engineers should be fully aware of all aspects of safety with regards to automated equipment. 2) Any commissioning or service engineer must be of a competent nature, trained and qualified to the local and national standards required to fulfill that job. These engineers should also be trained in the use and maintenance of the completed product. This includes being completely familiar with all associated documentation for the said product. All maintenance should be carried out in accordance with established safety practices. 3) All operators of the completed equipment should be trained to use that product in a safe and coordinated manner in compliance to established safety practices. The operators should also be familiar with documentation which is connected with the actual operation of the completed equipment. Note: The term 'completed equipment' refers to a third party constructed device which contains or uses the products associated with this document

The products in this document have been manufactured as general-purpose parts for general industries and have not been designed or manufactured to be incorporated in a device or system used in purposes related to human life. Before using the products in this document for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric. The products in this document have been manufactured under strict quality control. However, when installing the product(s) where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system. When combining the products in this document with other products, please confirm the standard and the code, or regulations with which the user should follow. Moreover, please confirm the compatibility of the products to the system, machine and apparatus which a user is using. If in doubt at any stage during the installation of the product(s), always consult a professional electrical engineer who is qualified and trained to the local and national standards. If in doubt about the operation or use, please consult the nearest Mitsubishi Electric distributor. Since the examples indicated by this document, technical bulletin, catalog, etc. are used as a reference, please use it after confirming the function and safety of the equipment and system. Mitsubishi Electric will accept no responsibility for actual use of the product(s) based on these illustrative examples. This documents content, specification etc. may be changed without a notice for improvement. The information in this document has been carefully checked and is believed to be accurate; however, if you have noticed a doubtful point, a doubtful error, etc., please contact the nearest Mitsubishi Electric distributor.

Registration
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. The company name and the product name to be described in this document are the registered trademarks or trademarks of each company.

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems
Table of Contents

Table of Contents
Introduction ............................................................................................................................... 5

1. The Basics of Positioning Control

1.1 What is positioning control? ............................................................................................................ 7 1.2 Actuators for positioning.................................................................................................................. 7 1.3 Positioning method type.................................................................................................................. 9

2. Positioning by AC Servo System

12

2.1 Advantages for using an AC servo system ................................................................................... 12 2.2 Examples of AC servo systems .................................................................................................... 13

3. Components of Positioning Control and Their Roles

15

3.1 Positioning controller..................................................................................................................... 18

3.1.1 Command pulse control method.................................................................................................... 18 3.1.2 Basic parameter settings ............................................................................................................... 19 3.1.3 Zero point return function .............................................................................................................. 20

3.2 Servo amplifier and servo motor ................................................................................................... 21

3.2.1 3.2.2 3.2.3 3.2.4 3.2.5 Positioning control in accordance with command pulse ................................................................ 21 Deviation counter function ............................................................................................................. 21 Servo lock function ........................................................................................................................ 21 Regenerative brake function.......................................................................................................... 21 Dynamic brake function ................................................................................................................. 22

3.3 Drive mechanism .......................................................................................................................... 23

3.3.1 Concept of drive system movement quantity................................................................................. 23 3.3.2 Setting the target position.............................................................................................................. 25

4. Learning to Use the FX Family for Positioning Control

26

4.1 FX PLC positioning ....................................................................................................................... 26

4.1.1 Overview of control........................................................................................................................ 26 4.1.2 Important memory locations .......................................................................................................... 29 4.1.3 Program examples ........................................................................................................................ 30

4.2 Inverter drive control ..................................................................................................................... 39

4.2.1 Overview of control........................................................................................................................ 39 4.2.2 Using the FX2N(C), FX3U(C) and FREQROL Inverter ..................................................................... 39 4.2.3 Program example .......................................................................................................................... 42

4.3 FX2N-1PG-E positioning................................................................................................................ 49

4.3.1 Overview of control........................................................................................................................ 49 4.3.2 Important buffer memory locations ................................................................................................ 49 4.3.3 Program example .......................................................................................................................... 50

4.4 FX2N-10PG positioning ................................................................................................................. 53

4.4.1 Overview of control........................................................................................................................ 53 4.4.2 Important buffer memory locations ................................................................................................ 53 4.4.3 Program example .......................................................................................................................... 54

4.5 FX2N-10GM and FX2N-20GM positioning ..................................................................................... 58

4.5.1 Overview of control........................................................................................................................ 58 4.5.2 Using dedicated software to set positioning for the FX2N-20GM................................................... 58 4.5.3 Testing and monitoring operations ................................................................................................ 64

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems
Table of Contents

4.6 FX3U-20SSC-H positioning ........................................................................................................... 66

4.6.1 4.6.2 4.6.3 4.6.4 4.6.5 Overview of control........................................................................................................................ 66 Using dedicated software to set positioning for the FX3U-20SSC-H ............................................. 67 Testing and monitoring operations ................................................................................................ 70 Important buffer memory locations ................................................................................................ 71 Program example .......................................................................................................................... 72

Revised History ....................................................................................................................... 76

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems
Introduction

Introduction
The purpose of this document is to guide beginners in understanding the basics of positioning control from general system setup examples to specific programming examples using the FX Series positioning family of controllers. After exploring the roles of the necessary positioning components, an overview of each product in the FX Family will be given in order to start programming. The following manuals are relevant sources and should be referred to when needed. Essential manual Manual required depending on application Manual with additional manual for detailed explanation
Manual name Manual number Contents Model name code

Manuals for PLC main unit Main unit

Supplied with product Additional Manual Supplied with product Supplied with product Supplied with product Supplied with product Supplied with product FX3U Series Hardware Manual FX3U Series Users Manual - Hardware Edition FX2N Series Hardware Manual FX2NC (DSS/DS) Series Hardware Manual I/O specifications, wiring and installation of the PLC main unit FX3U extracted from the FX3U JY997D18801 Series Users Manual - Hardware Edition. For detailed explanation, refer to the FX3U Series Users Manual - Hardware Edition. Details about the hardware including I/O JY997D16501 specifications, wiring, installation and maintenance of the FX3U PLC main unit. Details about the hardware including I/O JY992D66301 specifications, wiring, installation and maintenance of the FX2N PLC main unit. Details about the hardware including I/O specifications, wiring, installation and JY992D76401 maintenance of the FX2NC (DSS/DS) PLC main unit. Details about the hardware including I/O specifications, wiring, installation and JY992D87201 maintenance of the FX2NC (D/UL) PLC main unit. Details about the hardware including I/O JY992D89301 specifications, wiring, installation and maintenance of the FX1N PLC main unit. Details about the hardware including I/O JY992D83901 specifications, wiring, installation and maintenance of the FX3U PLC main unit.

09R516

09R508

09R509

FX2NC (D/UL) Series Hardware Manual FX1N Series Hardware Manual FX1S Series Hardware Manual

09R509

09R511

09R510

Programming
Additional Manual FX3U/FX3UC Series Items related to programming in PLCs Programming Manual including explanation of basic instructions, JY997D16601 Basic & Applied Instruction applied instructions and various devices in Edition FX3U/FX3UC PLCs. FX Series Programming Manual II JY992D88101 Items related to programming in PLCs including explanation of basic instructions, applied instructions and various devices in FX1S/FX1N/FX2N/FX2NC PLCs. 09R517

Additional Manual

09R512

Manuals for communication control Common When using each product, refer also to the main unit manual for the PLC main unit to be installed.
Additional Manual FX Series Users Manual Data Communication Edition Details of simple link between PCs, parallel JY997D16901 link, computer link and no-protocol communication (RS instructions, FX2N-232IF) 09R715

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems
Introduction

Essential manual Manual required depending on application Manual with additional manual for detailed explanation
Manual name Manual number Contents Model name code

Manuals for positioning control Common When using each product, refer also to the main unit manual for the PLC main unit to be installed.
Additional Manual FX3U/FX3UC Series User's Manual Positioning Control Edition JY997D16801 Details of positioning functions of FX3U/FX3UC Series

09R620

Pulse output and positioning When using each product, refer also to the main unit manual for the PLC main unit to be installed.
Supplied with product Supplied with product Supplied with product Additional Manual Supplied with product Supplied with product Additional Manual Additional Manual FX3U-2HSY-ADP Installation Manual FX2N/FX-1PG User's Manual FX2N-10PG Installation Manual FX2N-10PG User's Manual FX2N-10GM User's Guide Procedures for handling the high-speed output special adapter JY997D16401 When using, refer also to FX3U/FX3UC Series User's Manual - Positioning Control Edition. JY992D65301 Procedures for handling the 1-axis pulse output special function block Procedures for handling the 1-axis pulse output special function block When using, refer to FX2N-10PG User's Manual. Details of 1-axis pulse output special function block

09R610

JY992D91901

JY992D93401

09R611

Procedures for handling the 1-axis positioning special function unit JY992D77701 When using, refer to FX2N-10GM/FX2N-20GM Hardware/Programming Manual. Procedures for handling the 2-axis positioning special function unit JY992D77601 When using, refer to FX2N-10GM/FX2N-20GM Hardware/Programming Manual. JY992D77801 JY993D86801 Procedures for handling the 1-axis/2-axis positioning special function unit Procedures for handling the 1-axis/2-axis positioning special function unit

FX2N-20GM User's Guide FX2N-10GM/FX2N-20GM Hardware/Programming Manual FX-PCS-VPS/WIN-E Software Manual

09R612 09R612

Manuals for FX3U-20SSC-H Positioning Block SSCNET-III When using each product, refer also to the main unit manual for the PLC main unit to be installed.
Supplied with product Additional Manual Supplied with product FX3U-20SSC-H Installation Manual FX3U-20SSC-H User's Manual FX Configurator-FP Operation Manual Procedures for handling the 2-axis positioning special function block JY997D21101 When using, refer to FX3U-20SSC-H User's Manual. JY997D21301 JY997D21801 Describes FX3U-20SSC-H Positioning block details. Describes operation details of FX Configurator-FP Configuration Software.
-

09R622 09R916

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

1 The Basics of Positioning Control

1.1 What is positioning control?

1
The Basics of Positioning Control

1.
1.1

The Basics of Positioning Control

What is positioning control?
The positioning controller, together with the programmable logic controller, personal computer and operator interface, is one of the four main units of FA (factory automation). Among these units, the positioning controller plays an important role and is regarded as the center of the mechatronics field in which many senior engineers have been playing active roles. Positioning is all about motion, and motion often involves speed and precision. And since speed can be directly related to productivity, positioning is an area of much development. When the speed of a machine increases, a problem with the stop precision is often generated. In order to solve this problem, diversified grades of positioning controllers have been required and developed. Improving machine efficiency generates immeasurable added value, including reduced labor costs and improved conservation of machine floor space for the same quantity of production. If there are no problems related to the positioning aspect of a machine, it may mean that the machine is not running as efficiently as it could be. This is where the science of developing and retrofitting an optimum positioning control system comes in.

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

1.2

Actuators for positioning

The options available for positioning control depend on the type of actuator driving the system. An actuator is a mechanical device that moves or controls a specific element or a series of elements within a system. In a mechanical system, an actuator is often used with a sensor to detect the motion or position of a workpiece. The following illustrations provide examples of diversified actuators, their features and their weak points.
Actuator(s) Features and Drawbacks
Piping

Schematic drawing
Air cylinder

Pneumatic

Air source and high grade piping are required. High torque is not available. Multi-point positioning is complex and very difficult to achieve. Change in positioning is difficult.
Compressor

Workpiece

Brake motor

Positioning mechanism is simple. Repeatability is poor. Change in positioning is difficult. (When optical sensors or limit switches are used for stop)

Motor with brake Limit switch

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

1 The Basics of Positioning Control

1.2 Actuators for positioning

Actuator(s)

Features and Drawbacks

Schematic drawing
Constant quantity feed hopper

Clutch brake

Frequent positioning is possible. Life of friction plate is limited. Change in positioning is difficult. (When optical sensors or limit switches are used for stop)

Clutch brake unit

Speed reducer

Optical sensor Motor Can feed mechanism

Stepping motor

Simple positioning mechanism. If load is heavy, motor may step out and displacement can occur. Motor capacity is small. Precision is poor at high speed.

Controller

Stepping motor DC servo amplifier

Positioning precision is accurate. Maintenance is required for motor DC servo system brushes. It is not suitable for rotation at high speed.
DC servo motor

Lifter

Multi-speed positioning is available using a high-speed counter. General purpose inverter and High precision positioning is not general purpose available. motor Large torque is not available at start. (Specialized inverter is required)

Motor with brake

General-purpose inverter

Positioning precision is good. Maintenance is not required. Positioning address can be easily AC servo system changed. It is compact, and offers high power.

Cutter

Sheet material AC servo motor AC servo amplifier

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

1 The Basics of Positioning Control

1.3 Positioning method type

1.3

Positioning method type

In general, there are two methods to control the movement of a workpiece: speed control and position control. For basic, more rudimentary positioning, speed control can be used with an inverter and general purpose motor. For systems where precision is a must, servo systems are required for the advanced handling of pulse commands.
Control method Description Schematic drawing
Moving part B IM Ball screw Limit switch for changeover to low speed INV Limit switch for stop High speed DC0 to 10V Low speed

1
The Basics of Positioning Control

2
Positioning by AC Servo System

Two limit switches are provided in places where a systems moving part passes. At the first limit switch, the motor speed is reduced. At the second limit switch, the motor turns off and the brake turns on to stop the moving part. Limit switch In this method, because position controllers are not required, the method system configuration can be realized at reasonable cost.

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

(Guideline of stopping precision: Approximately 1.0 to 5.0 mm)*1 Speed control

IM: Inductive motor B: Brake INV: Inverter

Movement distance

A position detector (such as a pulse encoder) is set up in a motor or rotation axis. The pulse number generated from the position detector is counted by a high-speed counter. When the pulse number reaches the preset value, the moving part stops. Pulse count In this method, because limit method switches are not used, the stop position can be easily changed.

Pulses are fed back. PLG IM

Moving part Ball screw

INV DC0 to 10V PLC High-speed counter unit

IM: Inductive motor PLG: Pulse generator INV: Inverter PLC: Programmable controller High speed Low speed Movement distance

(Guideline of stopping precision: Approximately 0.1 to 0.5 mm)*1

Pulse Position command control method

An AC servo motor which rotates in proportion to the input pulse number is used as the drive motor. When the pulse number corresponding to the movement distance is input to the servo amplifier of the AC servo motor, positioning can be performed at high speed in proportion to the pulse frequency. (Guideline of stopping precision: Approximately 0.01 to 0.05 mm)*1

Pulses are fed back. PLG SM

Moving part Ball screw

Servo amplifier Command pulse PLC Position controller

SM: Servo motor PLG: Pulse generator PLC: Programmable controller

Movement distance

*1.

The stop precision shows a value in a case where the low speed is 10 to 100 mm/s.

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

1 The Basics of Positioning Control

1.3 Positioning method type

1. Speed Control
In speed control applications with inverters, stop precision is not very accurate. With the limit switch method, a system operates without any feedback to the controller to indicate the location of the workpiece. With the pulse count method, the speed can be changed and the stop command can be executed at specific distances (at specific timings) according to the feedback from the pulse generator connected to the motor. Both the limit switch method and the pulse count method, however, are subject to a loss in stop precision due to the dispersion of distance that occurs for workpieces at different speeds. When automatically stopping a moving part driven by a motor, stop the motor by a position signal (using a limit switch or pulse count comparison). In general conditions, turn on the brake at the same time. The moving part continues by a coasting distance until it completely stops, after the stop command is given. The coasting distance is not controlled and it is represented as the shaded part in the figure below.
Speed

Coasting distance

Stop command

Time Stop

Dispersion in the stop distance changes as shown below. Dispersion is affected by the speed of the workpiece when the stop command is given and the speed reduction time delay after stop.
Speed Speed reduction start Time delay

Dispersion in stop Time

Stop command

Stop

Stop

If the required stop precision is not satisfactory when stopping from the normal operation speed, the most effective method to improve the stop precision is to reduce the operation speed. However, if the operation speed is simply reduced, the machine efficiency may also be reduced. Therefore, in actual operation, the motor speed can be reduced from a high speed to a low speed before the motor is stopped, as shown below.
Speed High speed Time delay Poor stop precision Low speed Time Stop command Stop Speed reduction command Improved stop precision Speed High speed

Time Stop Stop command

10

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

1 The Basics of Positioning Control

1.3 Positioning method type

2. Position control
Using the pulse command method with a servo amplifier, the weak points described above for speed control are improved. A pulse encoder is attached to the servo motor to detect the motor rotation quantity (workpiece movement distance) and feed the information directly to the servo amplifier in order to continuously and directly control the high-speed positioning operation to the target position. This method allows the workpiece to stop with better precision and eliminates the coasting and dispersion distance at stop. Furthermore, limit switches to stop normal positioning operations, along with counting methods from the PLC are not needed.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

11

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

2 Positioning by AC Servo System

2.1 Advantages for using an AC servo system

2.
2.1

Positioning by AC Servo System

Advantages for using an AC servo system
With an AC servo system, positioning can be performed by many diversified methods. Typically, a position controller, servo amplifier and servo motor are required for positioning with an AC servo system. The representative servo system configuration is shown below.
Servo amplifier Commercial power supply Converter AC DC Smoothing circuit DC Inverter DC AC Servo motor SM

Command pulse Positioning controller

Speed Deviation command counter Current control

Feedback current PWM (pulse width modulation) control Feedback pulse

PLG Encoder

The positioning controller generates a specified quantity of forward rotation (or reverse rotation) pulses at a specified frequency.

The command pulse number is subtracted by the feedback pulse number, and the speed command to drive the servo motor is made from the deviation (accumulated pulse number). When the accumulated pulse number becomes 0, the servo motor stops.

The servo motor is equipped with a built-in encoder (pulse generator), dedicated to high speed response, and suitable for positioning control.

In the latest AC servo systems, conventional weak points have been improved as follows: Although the latest systems are completely digital, they are equipped with parameters in conformance to diversified mechanical specifications and electrical specifications so that simple set-up is possible. As frequent operation is enabled by a low inertia motor, the maximum torque is increased and the system can be applied to a wide variety of machines. The latest systems are equipped with an auto tuning function, with which the servo amplifier automatically detects the load inertia moment and adjusts the gain. This is possible even if the load inertia moment is unknown. The command communication cycle from the controller to the servo amplifier is improved for synchronization accuracy and better speed/positioning accuracy. The latest systems also allow for long-distance wiring, reduced noise resistance, and simplified wiring. The top advantages to using an AC servo system are described below.
Compact and light servo system In the FA workplace, a downsized AC servo system occupying less space is beneficial. Robust servo system In accordance with severe operation conditions, a tougher AC servo system is often required. Easy servo system AC servo systems are easier to handle than hydraulic equipment. Easy systems are also flexible for new staff. Good cost performance servo system An AC servo system with good cost performance saves a company in overall engineering costs.

12

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

2 Positioning by AC Servo System

2.2 Examples of AC servo systems

2.2

Examples of AC servo systems

Positioning indicates the operation to move an object, such as a workpiece or tool (drill or cutter), from one point to another point and to stop it with efficiency and precision. In other words, the principle of positioning is the control of speed in accordance with the position, performed to promptly eliminate the remaining distance to the target position. The flexibility to change the target position electrically and easily is an important requirement. Several cases of positioning using an AC servo motor are systematically shown below.
Type of machine Description Schematic drawing
Press main unit

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

Constant feed

In the press/shear process for cutting, punching, etc., the processed material is positioned with high precision to produce a constant sized product.

Uncoiler

Roll feeder

4
Learning to Use FX Positioning Control

Servo motor

Workpiece Drill M

Tapping

In order to tap a workpiece, 1. Quick feed, 2. Cutting feed and 3. Quick return are performed repeatedly.

Slide Timing belt M Pulley Feed motor Quick return Quick feed Cutting feed Ball screw

Drilling

Drill unit Y axis

In order to perform processing on a flat face, positioning with high Drilling in steel precision is performed by two motors sheet (X axis feed motor and Y axis feed motor).

X axis Workpiece X-Y table

M M

X axis feed motor Y axis feed motor

Index table

Index table

The position of the circular table is indexed. The index position is set on the outside (digital switch) or the inside (program). Shortcut drive is performed depending on the index position.

Worm wheel Servo motor

13

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

2 Positioning by AC Servo System

2.2 Examples of AC servo systems

Type of machine

Description

Schematic drawing
Servo amplifier

Lifter movingup/down

As negative load is applied on the servo motor in positioning of the lifter in the vertical direction, a regenerative option is also used. In order to hold the lifter stationary and prevent drop of the lifter by power interruption, a servo motor with an electromagnetic brake is used.

Lifter

Servo motor

Regenerative option

Cart

Cart travel control

A servo motor is mounted in the travel cart as the drive source. A mechanism such as rack and pinion is adopted to prevent slippage between the wheels and rails.
Drive wheel (on each of left and right sides)

Carrier robot

After the conveyor stops, the 2-axis servo system and the arm lifting mechanism transfer workpieces to a palette. The workpiece input positions on the palette can be set to many points so that setup change can be easily performed, even if the palette position and the palette shape change.

Travel head Y direction Slide arm Pallet Arm vertical axis (driven by air cylinder) Workpiece Conveyor Servo motor to drive travel head Servo motor to drive slide arm X direction

14

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

1
The Basics of Positioning Control

3.

Components of Positioning Control and Their Roles

Positioning control requires a number of components such as a positioning controller, servo amplifier, servo motor and drive mechanism. This section describes the role of each component. To begin, the following two-page spread illustrates how the seven key elements function together to perform positioning.

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

15

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

Position controller

AC power supply

Outputs the positioning speed and the movement quantity in command pulses to the servo amplifier. Transfers signals between the programmable controller. Controls return to the zero point.

Breaker

Power factor improving AC reactor

Radio noise filter

Electromagnetic contactor
Power board

Line noise filter

Near point DOG signal

Improves the power factor and cuts noise. Protects the power circuit.

In some types, the limit switch signal is wired to the position controller. Main circuit Position controller Converter Positioning command Command control pulse Parameter Zero point return control Servo ready Zero point signal (PG0)
Servo amplifier

Servo amplifier Smoothing Regenerative circuit brake DC Inverter DC AC Dynamic brake R

AC

DC

Speed Deviation command counter Current (Electronic gear) control Pulse magnification Counter clear

Feedback current PWM (pulse width modulation) control Feedback pulse

10

Operation switch

Manual pulse generator

Operation equipment

Gives inputs for manual/automatic mode, start/ stop, zero point return command, manual forward rotation/reverse rotation and manual pulse generator to the positioning controller.

Rectifies the AC power of the main circuit into the DC power in the converter, and smooths it in the smoothing circuit. When the DC power is converted into AC power in the inverter, the current supplied to the servo motor is changed by the PWM (pulse width modulation) control in the control circuit. The deviation counter receives and counts the command pulses from the positioning controller, subtracts the feedback pulses from them, then drives the servo motor until the accumulated pulse number becomes 0.

90
80
70
60

16

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

1
The Basics of Positioning Control

Servo motor

2
Positioning by AC Servo System

Dedicated to high speed response optimal to positioning control, has large start torque, large maximum torque and wide variable speed range 1/1 or more (1/1,000 to 1/5,000).

3
Components of Positioning Control

W hen a moving element goes beyond a limit switch (LS), the motor stops.
Servo motor

4
Learning to Use FX Positioning Control

Drive mechanism

In the case of large motor Cooling fan Limit switch (LS) Servo motor Speed reducer
Ball screw

Near point dog switch

Moving element

Limit switch (LS)

SM

Encoder PLG (pulse generator) When required Electromag netic brake

Auxiliary device such as chuck, drill and cylinder

Sensor, actuator, auxiliary device

Hand held Programmer

Personal Computer

The actuator (moving part drive mechanism) is equipped with speed reducer, timing belt, ball screw and limit switch. Diversified auxiliary devices are also controlled in accordance with positioning. The PLC or the positioning controller also controls auxiliary devices. The auxiliary device operation completed signal is output to the PLC or the position controller.

Setting / display unit

Used to write programs to the position controller, allows setting and display of the data.

17

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.1 Positioning controller

3.1

Positioning controller
Positioning controllers use programs and parameters to send positioning commands to the servo amplifier. Contents related to programs and parameters are described below.

3.1.1

Command pulse control method

There are two types of control formats used for outputting command pulses from an FX Series positioning controller: PLS/DIR (Pulse/Direction) method FP/RP (Forward Pulse/Reverse Pulse) method Each method requires two outputs from the controller to control specific signals for direction and pulse control. A third method, known as the A phase/B phase method, uses overlapping pulse signals to specify direction.

1. PLS/DIR method
In the PLS/DIR method, one output sends pulses to the drive unit while the other output specifies the direction of travel.
Forward rotation Output #1 Output #2 Pulse train H L Direction Reverse rotation

H L

ON*1

OFF*1

*1.

ON and OFF represent the status of the controllers output. H and L respectively represent the HIGH status and the LOW status of the waveform. The command pulse pattern in the figure assumes negative logic.

2. FP/RP method
In the FP/RP method, each output has a different direction and operates individually to send pulses to the drive unit.
Forward rotation
Output #1 Output #2 Forward rotation H pulse train (FP) L Reverse rotation H pulse train (RP) L OFF*2

Reverse rotation
OFF*2

*2.

ON and OFF represent the status of the controllers output. H and L respectively represent the HIGH status and the LOW status of the waveform. The command pulse pattern in the figure assumes negative logic.

18

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.1 Positioning controller

3.1.2

Basic parameter settings

To send a series of pulses (a pulse train) to a servo amplifier, positioning controllers use a specified feed quantity, which is proportional to the number of pulses. A feed speed must also be specified to control the number of pulses output per second.

1
The Basics of Positioning Control

1. Feed quantity
The feed quantity determined by the target address tells the servo system how far to move the workpiece. So, for example, if a servo motor encoder generates 8,192 pulses for one rotation, the command pulse number 8,192 can be output to rotate the servo motor by 1 rotation.

2
Positioning by AC Servo System

2. Feed speed
The feed speed defines the amount of travel per unit of time for the workpiece. When a servo motor encoder generates 8,192 pulses for one rotation, the command pulse frequency (speed) 8,192 pulses/s should be output to rotate the servo motor by 1 rotation per second. Decrease the pulse frequency to rotate the servo motor at a lower speed. Increase the pulse frequency to rotate the servo motor at a higher speed.

3
Components of Positioning Control

3. Acceleration/deceleration time
When the start command is given, acceleration, operation at constant speed, and deceleration are performed for positioning. Set the acceleration time and the deceleration time in the controllers parameters.
Parameter: Max. speed Positioning speed

4
Learning to Use FX Positioning Control

Speed

Actual acceleration time

Parameter: Acceleration time

Parameter: Deceleration time

Time Actual deceleration time

19

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.1 Positioning controller

3.1.3

Zero point return function

Many positioning systems include a home position to where a workpiece may need to return after performing various operations. For this reason, positioning controllers include a built-in function to return a workpiece to a defined position by using a mechanical DOG switch. To understand how this works, it is necessary to first understand when the function is needed according to the parameter setting of the servo amplifier and the type of servo motor encoder.

1. Incremental type servo motor encoder (pulse count method)

When the servo system uses an incremental or relative type encoder, the current value of the address stored in the position controller is not remembered or maintained when the power is turned off. This means that the address is set to zero every time the power is cycled, which can be disadvantageous in an application. Accordingly, every time the system is re-powered, it must be calibrated to the correct zero-point location by executing the zero point return function.

2. Absolute type servo motor encoder (absolute position detection system)

The absolute position detection system requires an absolute position motor encoder, a backup battery on the servo amplifier, and a parameter specification setting. It is constructed so that the current value stored in the positioning controller is always assured, regardless of power outages or movement while the power is turned off. The advantage to using this method is that after executing the zero point return function once, zero point return it is not needed again. Note The zero point return function does not actuate movement to a physical zero address. Instead, the zero point return function causes movement in a specified direction (positive or negative) in order to define the physical zero address after contact with a DOG switch. Example of DOG type zero return In the example to the left, the DOG (which is attached to the workpiece) comes in contact with the DOG switch to turn the DOG signal ON, which then initiates deceleration to creep speed. After the backward end of the DOG passes the DOG switch, turning the DOG signal OFF, the first detected zero point signal stops the motion, turns the CLEAR signal on, and sets the zero point address. The zero point address (specified in the controllers parameters) is typically zero. When the zero return function finishes, the zero point address is written to the current value register of the positioning controller to overwrite the current address. Since the zero point address is not always zero, the zero return function should be thought of as a homing function instead of a return-to-zero function. The zero point return direction, zero point address, zero signal count, return speed, deceleration time and creep speed are all set by parameters in the positioning controller.

Deceleration time Creep speed Zero point DOG switch DOG Forward end

Zero point return speed DOG switch activated Initial position Zero point return direction DOG Backward end

CLEAR signal * * The location of the DOG switch should be adjusted so that the backward end of the DOG is released between two consecutive zero point signals (1 pulse per rotation of the motor). In this example, the DOG length should not be less than the deceleration distance of the machine. Limit switch DOG switch

Initial position

Zero point

DOG search function In some PLC models, if the zero point return function is performed while the workpiece is stopped beyond the DOG switch, the machine moves until the limit switch is actuated, changes direction, then returns to the zero point again (DOG search function, zero point return retry function).

Escape operation

20

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.2 Servo amplifier and servo motor

3.2

Servo amplifier and servo motor

The servo amplifier controls the movement quantity and the speed according to the commands given by the positioning controller. The servo motor then transmits rotation to the drive mechanism after receiving signals from the servo amplifier.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3.2.1

Positioning control in accordance with command pulse

In accordance with speed and position command pulses from the positioning controller, PWM (pulse width modulation) control is performed by the main circuit of the servo amplifier in order to drive the motor. The rotation speed and the rotation quantity are fed back to the amplifier from the encoder attached to the servo motor.

3
Components of Positioning Control

3.2.2

Deviation counter function

The difference between the command pulses and the feedback pulses counted by the deviation counter in the servo amplifier is called accumulated pulses. While the machine is operating at a constant speed, the accumulated pulse quantity is almost constant. During acceleration and deceleration, the accumulated pulse quantity changes more dramatically. When the accumulated pulse quantity becomes equivalent to or less than a specified quantity (in-position set value) after command pulses have stopped, the servo amplifier outputs the positioning complete signal. The servo motor continues operation even after that. Then, when the accumulated pulse quantity becomes 0, the servo motor stops. The time after the servo motor outputs the positioning complete signal until it stops is called the stop settling time.
Speed Command speed Motor speed The accumulated pulse quantity is 0, and positioning is completed. Time

4
Learning to Use FX Positioning Control

Accumulated pulses Stop settling time

3.2.3

Servo lock function

The servo motor is controlled so that the accumulated pulse quantity counted in the deviation counter becomes 0. For example, if an external force for forward rotation is applied on the servo motor, the servo motor performs the reverse rotation operation to eliminate the accumulated pulses.
Accumulated pulses in deviation counter Minus pulses Plus pulses 0 (zero) Servo motor Reverse rotation operation Forward rotation operation Stop

3.2.4

Regenerative brake function

During deceleration, because the servo motor rotates by the load inertia of the drive mechanism, it functions as a generator and electric power returns to the servo amplifier. The regenerative resistor absorbs this electric power and functions as a brake (called a regenerative brake.) A regenerative brake is required to prevent regenerative over voltage in the servo amplifier when the load inertia is large and operations are frequently performed. The regenerative resistor is required when the regenerative power generation quantity during deceleration exceeds the allowable regenerative electric power of the servo amplifier.

21

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.2 Servo amplifier and servo motor

3.2.5

Dynamic brake function

When a circuit inside the servo amplifier is disabled by a power interruption in the AC power of the main circuit or actuation of the protective circuit, the terminals of the servo motor are short-circuited via resistors, the rotation energy is consumed as heat, then the motor immediately stops without free run. When the motor stops by elimination of the rotation energy, the brake is not effective and the motor runs freely.
Main circuit AC power supply NFB R S T U V W

Converter AC DC Deviation counter

Inverter DC AC D/A conversion

SM

PLG

Position controller

These contacts of the dynamic brake turn ON when the power is interrupted.

Number of rotations of motor

Motor stop characteristics when the dynamic brake is actuated When the dynamic brake is not actuated Time Power: OFF Contacts of dynamic brake: ON

22

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.3 Drive mechanism

3.3

Drive mechanism
The drive mechanism converts the rotation motion of the servo motor into reciprocating or vertical motion through a speed reducer, timing belt, ball screw, etc. to move the machine.

1
The Basics of Positioning Control

3.3.1

Concept of drive system movement quantity

The following diagram is a representative AC servo motor positioning system.
Encoder Servo motor N0 Speed reducer 1 n Moving part v0

2
Positioning by AC Servo System

3
Components of Positioning Control

PB

Pf Servo amplifier

: Transfer distance per pulse (mm/pulse)

v0 : Moving part speed during quick feed (mm/min) PB : Lead of ball screw (mm/rev) 1
n

4
Learning to Use FX Positioning Control

: Speed reduction ratio

S : Transfer distance per rotation of motor (mm/rev) f0 N0 : Number of rotations of motor during quick feed (rev/min) Pf : Feedback pulse number (pulse/rev) Position controller f0 : Command pulse frequency during quick feed (pulse/sec)

The servo motor stops with the precision , which is within 1 pulse against the command pulse. The movement quantity of the workpiece is: [Output pulses from position controller] x [ ] The moving part speed is: [f0] x [ ] Either mm, inch, degree, or pulse can be selected for the positioning command unit. Accordingly, when data such as the movement quantity per pulse, positioning speed, or the positioning address in accordance with the positioning command unit are set, pulse trains are output for the target address, and positioning is performed.

23

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.3 Drive mechanism

Useful equations To define the system illustrated above, and v0 need to be determined using a series of equations. The speed of the moving part (v0) is constrained by the mechanical gearing system between the servo motor and moving part, the pitch of the ball screw, and the specification of the motor as shown through the following two formulas. Transfer distance per rotation of motor
S
mm rev = PB

1 n

Number of rotations of motor during quick feed

rev min v0 Rated number of rotations of servo motor

N0

If N0 does not exceed the rated speed of the motor, this means that the servo system can be used for the application. In order to determine if the positioning controller is applicable, the command pulse frequency during quick feed (f0) should be checked to verify it does not exceed the maximum allowable frequency setting for the maximum speed parameter setting of the controller. Transfer distance per pulse

mm PLS =

S Pf

(Electronic gear ratio)

Command pulse frequency during quick feed

f0
PLS S =

N0

1 60

During the above process, the Electronic gear ratio (often CMX/CDV for Mitsubishi servos) and Speed reduction ratio can be adjusted to fit the applications needs. In each of the absolute and incremental positioning methods, the entire movement distance of the machine should not exceed the maximum allowable pulse output number from the positioning controller.

24

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

3 Components of Positioning Control and Their Roles

3.3 Drive mechanism

3.3.2

Setting the target position

In positioning control, the target position can be set by the following two methods, specified by the controllers parameter settings. (Available command units are mm, inch, degree, or pulse.)

1
The Basics of Positioning Control

1. Absolute method
In this method, a point (absolute address) is specified for positioning while the zero point is regarded as the reference. The start point is arbitrary.
Address 100 Address 100 Address 150 Address 300 Address 150 Address 100 Address 150 0 Zero point 100 Point A 150 Point B 300 Point C Start point End point

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

2. Incremental method
In this method, positioning is performed through specification of the movement direction and the movement quantity while the current stop position is regarded as the start point.
Movement quantity +100 Movement quantity +100 Movement quantity -100 Start point End point

Movement quantity +100 Movement quantity -150 Movement quantity -100 Movement quantity +50 0 Zero point 100 Point A 150 Point B 300 Point C

25

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

4.
4.1

Learning to Use the FX Family for Positioning Control

FX PLC positioning
The FX1S, FX1N and FX3U(C) Series PLC main units include basic positioning instructions to send command pulses to a stepper motor or servo amplifier. While FX PLCs support point-to-point positioning, full control is also available for reading the absolute position from a servo amplifier, performing zero return, and altering the workpiece speed during operation. Important references for understanding positioning with FX PLCs include: FX Series Programming Manual II (JY992D88101) FX3U/FX3UC Series Programming Manual (JY997D16601) FX3U/FX3UC Series Users Manual - Positioning Control Edition (JY997D16801) It is assumed that you will have read and understood the above manuals or that you will have them close at hand for reference.

4.1.1

Overview of control
1. Number of Axes
The FX1S and FX1N transistor type PLCs support positioning on 2 axes with operation speeds up to 100,000 pulses/second (100 kHz). The FX3U(C) transistor type PLC main units support positioning speeds up to 100 kHz on 3 axes. If two FX3U-2HSY-ADP adapters are connected to the FX3U, 4 axes are available with operation speeds up to 200 kHz. The PLS/DIR pulse output method is used for all PLC main units to output pulses as shown in the following table.
1st Axis Applicable Model Pulse Output Direction Output*
1

2nd Axis FX3U(C)

3rd Axis

4th Axis

FX1S, FX1N FX3U + (2) FX3U-2HSY-ADP*2*3 Y0 Y4 Y1 Y5 Y2 Y6 Y3 Y7

*1. *2. *3.

Output terminals for direction can be specified arbitrarily when the FX3U-2HSY-ADP is not used. Y4, Y5, Y6 and Y7 are used as an example. The FP/RP pulse output method is also available with the FX3U-2HSY-ADP. The FX3UC can not be connected with the FX3U-2HSY-ADP.

26

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

2. Limit switches
As with any other positioning system, inputs are needed to detect when the workpiece reaches the outer boundary limits in order to prevent damage to the machine. For the FX3U(C) programmable logic controller, limits are wired to the controller to be used with the DOG search zero return function for reversing the motors direction of travel in order to hunt for the DOG switch. These limits are called the forward rotation limit (LSF) and the reverse rotation limit (LSR). Hardware limits are used on the servo amplifier side to stop the motor in worst case scenarios. Example of limit switches for the FX3U(C) PLC:
Reverse rotation limit 2 (Servo amplifier side) Servo motor Reverse rotation Forward rotation Reverse rotation limit 1 (Programmable controller side) LSR Forward rotation limit 1 (Programmable controller side) LSF Forward rotation limit 2 (Servo amplifier side)

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

3. Sink vs. Source outputs

In general, MELSERVO Series amplifiers are configured with sink type inputs. To communicate appropriately with sink type inputs, sink type outputs are used on the PLC side. Therefore, when using a Mitsubishi servo control system, a transistor sink output type PLC is used.

4
Learning to Use FX Positioning Control

4. Options for positioning

Before choosing a PLC for a positioning system, it is important to understand the instructions available for each PLC. The FX1S and FX1N include the same set of positioning instructions. The only disadvantage to choosing an FX1S PLC for positioning is that it does not include as many I/O and that it cannot be expanded with special function blocks for analog or communication control. The FX3U, combined with high speed positioning adapters, can operate with higher pulse output frequencies and includes 3 additional positioning instructions. The available instructions for FX PLCs are described in the chart below.
Applicable Model Description Positioning instruction Instruction Illustration
Speed JOG speed

FX1S FX1N FX3U(C)

JOG operation The motor moves in a specified direction depending on the logic and timing of the drive input signal. (There is no target position.)

DRVI
Start JOG command Start Speed Operation speed Stop Stop

FX1S FX1N FX3U(C)

1-speed positioning A start command accelerates the motor to a constant speed and moves the workpiece to a specified distance.

DRVI DRVA
Start Travel distance Target position

27

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

Applicable Model

Description

Positioning instruction

Instruction Illustration

FX1S FX1N FX3U(C)

Zero return The machine moves at a specified speed until the DOG input turns ON. The workpiece then slows to creep speed and stops before the CLEAR signal is output.

Speed

Zero point return speed

Creep speed

ZRN
Zero point DOG input ON CLEAR signal Start

FX1S FX1N FX3U(C)

Variable speed operation After starting with a specified speed, the motor can change its speed depending on commands from the PLC. (For the FX1S and FX1N, acceleration to different speeds is approximated with the RAMP instruction) Interrupt 1-speed positioning When an interrupt signal turns ON, the workpiece travels a specific distance at the same speed before decelerating to stop.

Speed

PLSV (RAMP)
Start Speed change Speed change

Speed

Travel distance

FX3U(C)

DVIT

Start Limit (LSR)

Interrupt input

FX3U(C)

DOG search zero return The machine operates similar to the zero return instruction except for features to hunt for the DOG switch and to use the zero-phase signal.

DOG Origin Start

DSZR

Input

FX3U(C)

Table operation For programming simplicity, position and speed data can be organized in table format for the DRVI, DRVA, DVIT and PLSV instructions.

DTBL Input

Y0

K1 Y000 is positioned by the operation in table number 1-3

DTBL
Input

DTBL

Y0

K2

DTBL

Y0

K3

Axis Table No.

28

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

4.1.2

Important memory locations

For FX PLC programs using positioning instructions, there are several built-in memory addresses to define control parameters and facilitate system operation. These addresses consist of 1-bit, 16-bit, and 32-bit address locations and are briefly outlined below according to their use in the example programs in the following section. Use this table as a reference to understand the example programs. For details on other memory addresses (for example, operation information for control on Y001 or Y002), refer to the FX3U/FX3UC Series Users Manual - Positioning Control Edition (JY997D16801).
Function name RUN monitor Initial pulse Instruction execution complete flag CLEAR signal output enable Pulse output stop command Pulse output monitor flag Instruction execution abnormally complete flag CLEAR signal output function enable (Y000) Zero return direction specification Forward rotation limit Reverse rotation limit (Y000) Positioning instruction activation CLEAR signal device specification function enable Bias speed [Hz] Address M8000 M8002 M8029 Length 1-bit 1-bit 1-bit Description ON when PLC is in RUN. ON for the first scan only. Applicable PLC FX1S, FX1N, FX3U(C) FX1S, FX1N, FX3U(C)

1
The Basics of Positioning Control

2
Positioning by AC Servo System

Programmed immediately after a positioning instruction. Turns ON when the preceding FX1S, FX1N, FX3U(C) instruction finishes its operation and stays ON until the instruction stops being driven. Enables a CLEAR signal to be output to the servo. Stop outputting Y000 pulses. (Immediate stop) OFF when Y000 is READY ON when Y000 is BUSY Programmed immediately after a positioning instruction. Turns ON when an instruction fails to complete correctly and stays ON until the instruction stops being driven. Enables an output to be used for the CLEAR signal for Y000. OFF ON Reverse rotation Forward rotation FX1S, FX1N FX1S, FX1N FX3U(C) FX1S, FX1N FX3U(C) FX3U(C)

3
Components of Positioning Control

M8140 M8145 M8349 M8147 M8340 M8329

1-bit 1-bit 1-bit

4
Learning to Use FX Positioning Control

1-bit

M8341 M8342 M8343 M8344 M8348 M8464 D8145 D8342 D8146 D8343

1-bit 1-bit 1-bit 1-bit 1-bit 1-bit

FX3U(C) FX3U(C) FX3U(C) FX3U(C) FX3U(C) FX3U(C) FX1S, FX1N FX3U(C)

Forward pulses on Y000 stop when this relay turns ON. Reverse pulses on Y000 stop when this relay turns ON. OFF when a positioning instruction is not active. ON when a positioning instruction is active. Enables the output terminal for the CLEAR signal to be changed for Y000. Sets the bias speed for Y000. Sets the maximum instructions on Y000. speed for positioning

16-bit

Maximum speed [Hz] Acceleration/ deceleration time [ms] Acceleration time [ms] Deceleration time [ms] CLEAR signal device specification

32-bit 16-bit 16-bit 16-bit 16-bit

FX1S, FX1N FX3U(C) FX1S, FX1N FX3U(C) FX3U(C) FX3U(C)

D8148 D8348 D8349 D8464

Sets the acceleration and deceleration time. Sets the acceleration time for Y000. Sets the deceleration time for Y000. Sets the output terminal for the CLEAR signal for Y000.

29

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

4.1.3

Program examples
Two positioning examples are included as a reference to get started with PLC programming.

1. Hybrid programming example for FX1S, FX1N, FX3U(C) PLCs

The first example below illustrates zero return and absolute positioning control on 1 axis with an FX1S, FX1N or FX3U(C) PLC. Since the memory addresses for utilizing positioning instructions is different depending on the PLC, please note that the following program is a hybrid program and that memory addresses must be changed according to the type of PLC. A general understanding of step ladder and ladder logic is necessary to use the program.
#2) Forward positioning Output pulse frequency: 100,000 Hz 100 #1) Origin after zero return 500,000 Bias speed: 500Hz 500Hz #3) Reverse positioning Reverse rotation limit 2 (Servo amplifier side) Servo motor Reverse rotation Forward rotation Forward rotation limit 2 (Servo amplifier side)

Acceleration/deceleration time: 100 ms

The following inputs and outputs are used:

Input X000 X001 X002 X003 X004 X005 X006 Immediate stop Zero return command Forward rotation positioning command Reverse rotation positioning command Stop command Near-point signal (DOG) Servo ready Y000 Y004 Y010/Y002 Output Pulse train output Rotation direction signal CLEAR signal

X000 Immediate stop X006 Servo ready

*Use this for FX3U(C) PLCs M8349 *Use this for FX1S and FX1N PLCs

Stops outputting Y000 pulses. (Immediate stop) Stops outputting Y000 pulses. (Immediate stop) Resets "zero return completion" flag. Resets "forward rotation positioning completion" flag. Resets "reverse rotation positioning completion" flag. Enables the zero return operation with CLEAR signal outputting function. (CLEAR signal: Y010)

M8145

RST RST

M10 M11

RST

M12

M8000 RUN monitor

*Use this for FX3U(C) PLCs FNC 12 MOVP H0010 D8464

M8464 M8341 *Use this for FX1S and FX1N PLCs M8140 Return to the zero point with CLEAR signal output Y002.

30

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

1
The Basics of Positioning Control
*Use this for FX3U(C) PLCs S0 S20 S21 M8349 Y000 output stop M5 Operation is stopped.

Return to Positioning Positioning zero point in forward in reverse rotation rotation *Use this for FX1S and FX1N PLCs S0 S20 S21

2
Positioning by AC Servo System
M5 Operation is stopped.

M8349 Y000 output stop

Return to Positioning Positioning zero point in forward in reverse rotation rotation M8002 Initial pulse

3
Components of Positioning Control
FNC 12 DMOV FNC 12 MOV FNC 12 MOV FNC 12 MOV K100000 K500 K100 K100 D8343 D8342 Sets the maximum speed. 100,000(Hz) D8344,D8343 Sets the bias speed. 500(Hz) D8342 Sets the acceleration time. 100(ms) D8348 Sets the deceleration time. 100(ms) D8349

*Use this for FX3U(C) PLCs

D8348 D8349

4
Learning to Use FX Positioning Control

*Use this for FX1S and FX1N PLCs FNC 12 DMOV FNC 12 MOV FNC 12 MOV K100000 K500 D8146 D8145 Sets the maximum speed. 100,000(Hz) D8147,D8146 Sets the bias speed. 500(Hz) D8145 Sets the acceleration/ deceleration time. 100(ms) D8148

K100

D8148

X001

M5

RST RST RST SET

M10 M11 M12 S0

Return to Operation zero point stopped

Resets "zero return completion" flag. Resets "forward rotation positioning completion" flag. Resets "reverse rotation positioning completion" flag. Enters the zero point return state (S0).

X002 Positioning in forward rotation

M5

M10

RST RST SET

M11 M12 S20

Operation "Zero return completion" flag stopped

Resets "forward rotation positioning completion" flag. Resets "reverse rotation positioning completion" flag. Enters the foward rotation positioning state (S20).

X003 Positioning in reverse rotation

M5

M10

RST RST SET

M11 M12 S21

Operation "Zero return completion" flag stopped

Resets "forward rotation positioning completion" flag. Resets "reverse rotation positioning completion" flag. Enters the reverse rotation positioning state (S21).

31

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

STL M50 X004

*1

S0

Zero return Zero return instruction (CLEAR signal: Y010: FX3U(C) Y002: FX1S,FX1N)

Waiting for Stop 1 scan time command

FNC 156 DZRN

K50000 Zero return start speed

K1000 Creep speed

X005

Y000

M8029 "Execution completion" flag Zero return *Use this for FX3U(C) PLCs M8340 M50 #1)

Near-point Pulse signal output destination number SET M10

"Zero return completion" flag

Y000 Waiting for Outputting 1 scan time *Use this for FX1S and FX1N PLCs M8147 M50

RST

S0

End of zero return (Self-reset)

Y000 Waiting for Outputting 1 scan time M8000 RUN monitor

RST

S0

End of zero return (Self-reset)

*2 M50 Waiting for 1 scan time

STL M51 Waiting for 1 scan time Positioning in forward rotation direction X004 *1 FNC 159 DDRVA K500000 K100000 Y000

S20

Positioning in forward rotation direction Moves to absolute position 500000 using the drive to Absolute instruction. (Y004=ON)

Stop command

Y004
Rotation direction signal

M8029 "Execution completion" flag *Use this for FX3U(C) PLCs M8340 M51

Designation Output Pulse of absolute pulse output position frequency destination number

SET

M11

"Forward rotation positioning completion" flag

#2)

RST Y000 Waiting for Outputting 1 scan time *Use this for FX1S and FX1N PLCs M8147 M51 RST

S20

Ends the positioning operation in the forward rotation derection. (Self-reset)

Y000 Waiting for Outputting 1 scan time M8000 RUN monitor

S20

Ends the positioning operation in the forward rotation derection. (Self-reset) *2

M51

Waiting for 1 scan time

*1. *2.

To stop the positioning operation, be sure to insert the stop contact before the positioning instruction so that STL instruction cannot be turned off (reset) until "pulse output monitor" flag (M8340 or M8147 (for Y000)) is turned off. To prevent simultaneous activation of positioning instructions, the instruction activation timing should be delayed by 1 scan time.

32

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

1
The Basics of Positioning Control
STL M52 Waiting for 1 scan time M8029 "Execution completion" flag *Use this for FX3U(C) PLCs M8340 M52 RST S21 X004
*3

S21

Positioning in reverse rotation direction Moves to absolute position 100 using the drive to Absolute instruction. (Y004=OFF)

Positioning in reverse rotation direction

Stop command

FNC 159 DDRVA

K100

K100000

Y000

Y004

2
Positioning by AC Servo System

Designation Output Pulse Rotation of absolute pulse output direction position frequency destination signal number

SET

M12

"Reverse rotation positioning completion" flag Ends the positioning operation in the reverse rotation direction. (Self-reset)

#3)

3
Components of Positioning Control

Y000 Waiting for Outputting 1 scan time *Use this for FX1S and FX1N PLCs M8147 M52

Y000 Waiting for Outputting 1 scan time M8000

RST

S21

Ends the positioning operation in the reverse rotation direction. (Self-reset) *4

4
Learning to Use FX Positioning Control

M52 RUN monitor

Waiting for 1 scan time

RET

END *3. *4. To stop the positioning operation, be sure to insert the stop contact before the positioning instruction so that STL instruction cannot be turned off (reset) until "pulse output monitor" flag (M8340 or M8147 (for Y000)) is turned off. To prevent simultaneous activation of positioning instructions, the instruction activation timing should be delayed by 1 scan time.

2. Programming example for the FX3U(C) PLC

The following program is similar to the previous one except that it is programmed only in ladder logic and does not follow a specific sequence of step ladder states. Additionally, it includes control for relative positioning with JOG(+) and JOG(-) commands, a DOG search zero return function, and utilization of the DTBL instruction. When using an FX3U(C) PLC, the DOG search zero return function can be programmed with limit switches wired to the PLC as follows.
Reverse rotation limit 2 (Servo amplifier side) Servo motor Reverse rotation Forward rotation Reverse rotation limit 1 (Programmable controller side) LSR Forward rotation limit 1 (Programmable controller side) LSF Forward rotation limit 2 (Servo amplifier side)

The DTBL instruction helps to simplify the programming code and is set up beforehand (along with positioning parameters such as the bias speed, acceleration/deceleration, etc.) with GX Developer.

33

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

Forward positioning Output pulse frequency: 100,000 Hz 100 Origin after zero return

500,000 Bias speed: 500Hz 500Hz

In this example, positioning may be performed arbitrarily along the path to the left. Using the JOG command, the workpiece is moved to any relative position. This is not illustrated to the left.

Reverse positioning Acceleration/deceleration time: 100 ms

Required hardware and software are as follows: 1) FX3U(C) PLC version 2.20 or later 2) GX Developer 8.23Z or later Parameters for the DTBL instruction are set in GX Developer as shown below.
a) Double-click [Parameter] and then [PLC parameter] from the project tree on the left side of the screen. If the project tree is not displayed on the screen, click [View] on the menu bar, and then click [Project Data List].

b) Click on the [Memory capacity] tab and then enter a check in the [Positioning Instruction Settings] check box. Take note that 9,000 steps are needed to set the positioning data. Therefore, it is necessary to specify a [Memory capacity] of 16,000 steps or more.

34

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

1
The Basics of Positioning Control

c) Click on the [Positioning] tab and then set Y000 (pulse output destination) as follows. Setting item Bias speed (Hz) Maximum speed (Hz) Creep speed (Hz) Zero return speed (Hz) Acceleration time (ms) Deceleration time (ms) Interrupt input for DVIT instruction Setting value 500 100,000 1000 50,000 100 100 X000

2
Positioning by AC Servo System

3
Components of Positioning Control

d) Click the [Individual setting] button. The Positioning instruction settings window will appear. In this window, click on the [Y0] tab to display the positioning table for Y000 (pulse output destination). Set the data in the positioning table as follows: Setting item Rotation direction signal First device Positioning type No. 1 Number of pulses (PLS) Frequency (Hz) Positioning type Be sure to change the [Rotation direction signal] to Y004. e) Click the [OK] button and then the [End] button to close the parameters. f) Create the ladder program as shown below. No. 2 Number of pulses (PLS) Frequency (Hz) Positioning type No. 3 Number of pulses (PLS) Frequency (Hz) Positioning type No. 4 Number of pulses (PLS) Frequency (Hz) R0 DDRVI (Drive to increment) 999,999 30,000 DDRVI (Drive to increment) -999,999 30,000 DDRVA (Drive to absolute) 500,000 100,000 DDRVA (Drive to absolute) 100 100,000 Setting value Y004

4
Learning to Use FX Positioning Control

35

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

g) Once the ladder program is complete, click on [Online] from the top menu bar in GX Developer and select [Write to PLC]. The Write to PLC window will appear. h) Click the [Param + Prog] button and then click the [Execute] button. The parameters and the created program will be transferred to the PLC. To enable the transferred parameters, stop the PLC and then restart it.

The following inputs and outputs are used:

Inputs X004 X010 X014 X020 X021 X022 X023 X024 X025 X026 X027 X030 Zero-point signal Near-point signal (DOG) Servo ready Immediate stop Zero return command JOG(+) command JOG(-) command Forward rotation positioning command Reverse rotation positioning command Forward rotation limit (LSF) Reverse rotation limit (LSR) Stop command Y000 Y004 Y020 Outputs Pulse train output Rotation direction signal CLEAR signal

36

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

1
The Basics of Positioning Control
X020 Immediate stop X014 Servo ready M8349 RST RST RST X026 Forward rotation limit X027
*1

Stops outputting Y000 pulses. (Immediate stop) Resets "zero return completion" flag. Resets "forward rotation positioning completion" flag. Resets "reverse rotation positioning completion" flag. Normal rotation limit (Y000) Reverse rotation limit (Y000) Enables the zero return operation with CLEAR signal outputting function. (CLEAR singal: Y020)

M10 M12 M13 M8343 M8344

2
Positioning by AC Servo System

Reverse rotation limit M8000 RUN monitor

*1

3
Components of Positioning Control

FNC 12 MOVP

H0020

D8464

M8464 M8341 M8000 RUN monitor X021 M8348 M101 M102

Abnormal end of zero retum

4
Learning to Use FX Positioning Control
Performs zero return in the forward rotation direction. Resets "zero return completion" flag. Resets "forward rotation positioning completion" flag. Resets "reverse rotation positioning" completion flag. Zero return is being performed. Zero return instruction with DOG search function (CLEAR singal: Y020)

M8342

Zero Positioning Normal return being end of performed zero (Y000) retum

RST RST RST

M10 M12 M13 M100

DOG search zero return

M100 Zero retum being performed X030 Stop command M8029 "Execution completion" flag M8329 Abnormal end X022 M8348 JOG Positioning (+) being performed (Y000) M104 Completes the JOG(+) operation.

FNC 150 DSZR

X010

X004

Y000

Y004

Near-point Zero-point signal signal

Pulse Rotation output direction destination signal number

SET

M10 M101 M102

"Zero return completion flag Normal end of zero return Abnormal end of zero return

RST RST

M12 M13 M103

Resets "forward rotation positioning completion" flag. Resets "reverse rotation positioning" completion flag. JOG(+) operation is being performed. Executes No. 1 of the positioning table of Y000 (pulse output destination).

JOG(+) operation

M103 JOG(+) operation is being performed. X030 Stop command X022 JOG(+) M8329 Abnormal end

FNC 152 DTBL

Y000

K1

Pulse Table output number destination number M104

Completes the JOG(+) operation.

*1. The forward and reverse rotation limit switches must be wired so that they are turned ON by default. When these limit switches turn OFF (due to the workpiece going out-of-bounds), M8343 or M8344 will turn ON and cause the pulse operation to stop.

37

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.1 FX PLC positioning

X023 M8348 JOG Positioning (-) being performed (Y000) M105 JOG(-) operation is being performed.

M106 Completes the JOG(-) operation.

RST RST

M12 M13 M105

Resets "forward rotation positioning completion" flag. Resets "forward rotation positioning completion" flag. JOG(-) operation is being performed. Executes No. 2 of the positioning table of Y000 (pulse output destination).

JOG(-) operation

X030 Stop command X023 JOG(-) M8329 Abnormal end

FNC 152 DTBL

Y000

K2

Pulse Table output number destination number M106

Completes the JOG(-) operation.

X024 M8348 Positioning in forward rotation direction

Positioning in forward rotation direction Positioning operation being performed (Y000)

M10
"Zero return completion" flag

M108
Normal end of positioning in forward rotation direction

M109
Abnormal end of positioning in forward rotation direction

RST RST

M12 M13 M107

"Forward rotation positioning completion" flag "Reverse rotation positioning completion" flag Positioning operation being performed in forward rotation direction Executes No. 3 of the positioning table of Y000 (pulse output destination).

M107
Positioning operation being performed in forward rotation direction

X030 Stop command

FNC 152 DTBL

Y000

K3

Table Pulse output number destination number SET M12 M108 M109

M8029 "Execution completion" flag M8329 Abnormal end X025 M8348 M10
"Zero return completion" flag

"Forward rotation positioning completion" flag "Forward rotation positioning normal end" flag "Forward rotation positioning abnormal end" flag

M111
Normal end of positioning in reverse rotation direction

M112
Abnormal end of positioning in reverse rotation direction

RST RST

M12 M13 M110

Positioning in reverse rotation direction

Positioning in reverse rotation direction

Positioning operation being performed (Y000)

"Forward rotation positioning completion" flag "Reverse rotation positioning completion" flag Positioning operation being performed in reverse rotation direction Executes No. 4 of the positioning table of Y000 (pulse output destination).

M110
Positioning operation being performed in reverse rotation direction

X030 Stop command

FNC 152 DTBL

Y000

K4

Table Pulse output number destination number SET M13 M111 M112 END

M8029 "Execution completion" flag M8329 Abnormal end

"Reverse rotation positioning completion" flag "Reverse rotation positioning normal end" flag "Reverse rotation positioning abnormal end" flag

38

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

4.2

Inverter drive control

Inverters are essentially the opposite of electrical rectifiers since they are used to convert direct current (DC) into alternating current (AC). In factory automation, inverters (sometimes known as variable frequency drives) are used to efficiently control large current loads through voltage regulation to drive oversized fans, pumps or AC motors. Drive control with inverters can lead to great reductions in energy consumption for a factory. With a Mitsubishi general-purpose inverter connected to an FX2N(C) or FX3U(C) PLC, a motor can be controlled to move at a specific speed. Through monitoring feedback or by using limit switches, a basic positioning functionality is achieved. However, as described in Chapter 1, Section 1.3, the disadvantage to using an inverter to move a workpiece to a specific location is a loss in the stop precision. Therefore, inverters should not be thought of as positioning controllers. Important references for understanding inverter drive control for this section include: FX Series Users Manual - Data Communication Edition (JY997D16901) F700 Inverter Instruction Manual (Applied) (IB(NA)-0600177ENG) It is assumed that you will have read and understood the above manuals or that you will have them close at hand for reference.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

4.2.1

Overview of control
Programmable logic controllers and inverters communicate with each other through passing parameter data and control operation data back and forth. Inverters, when used for variable frequency drive, require a frequency command and a start command to operate. Mitsubishis FREQROL Series inverters communicate with FX2N(C) and FX3U(C) PLCs via the Mitsubishi inverter computer link protocol to asynchronously control operations.

4.2.2

Using the FX2N(C), FX3U(C) and FREQROL Inverter

In order to enable RS485 serial communication to a MELCO inverter(s), a special BD board or adapter (ADP) is connected to the main unit FX2N(C) or FX3U(C). The following table describes connection options for using one channel of communication.
FX Series Communication equipment (option) Total extension distance

50 m
FX2N-485-BD (Terminal board)

FX2N

FX2N-ROM-E1 (Function extension memory cassette)

or
FX2N-CNV-BD FX2NC-485ADP
(Terminal block)

500 m
FX2N-CNV-BD FX0N-485ADP

(Terminal block)

39

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

FX Series

Communication equipment (option)

Total extension distance

MITSUBISHI
X0 X1 X2 X3 X4 X5 X6 X7 Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7

FX2NC

or
FX2NC-485ADP
(Terminal block)

500 m
FX0N-485ADP
(Terminal block)

FX2NC-ROM-CE1 (Function extension memory board)

ch1
RD A RD RD B

SD A

SD

SD B

50 m

SG

FX3U-485-BD
(Terminal block)
RUN

STOP

FX3U
RD

ch1
RD A

ch1

RD B

SD A

SD

SD B

500 m

SG

FX3U-CNV-BD FX3U-485-BD
(Terminal block)

FX3U-485ADP(-MB)
(Terminal block)

ch1

500 m
FX3UC

FX3U-485ADP(-MB)
(Terminal block)

To use the special inverter communication instructions from the PLC, inverter and PLC communication parameters must be set. The FX2N(C) and FX3U(C) PLCs include the following special instructions to communicate with an inverter(s).
FX2N(C) K10 EXTR K11 K12 K13 FX3U(C) IVCK IVDR IVRD IVWR IVBWR*1 Function/Description Monitors operations of an inverter. Controls operations of an inverter. Reads a parameter from an inverter. Writes a parameter to an inverter. Writes a block of parameters to an inverter.

*1.

This instruction is only available for FX3U(C) PLCs.

40

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

The programmable controller special auxiliary relays and inverter instruction codes listed in the table below are used in Section 4.2.3. For information on memory addresses that contain error codes and inverter communication operation statuses, refer to the FX Series Users Manual - Data Communication Edition (JY997D16901).
Function name RUN monitor Initial pulse Instruction execution complete flag Address M8000 M8002 Length 1-bit 1-bit Description ON when PLC is in RUN. ON for the first scan only. Applicable PLC FX2N(C), FX3U(C) FX2N(C), FX3U(C)

1
The Basics of Positioning Control

2
Positioning by AC Servo System

M8029

1-bit

Programmed immediately after an inverter communication instruction. Turns ON when the preceding instruction finishes its FX2N(C), FX3U(C) operation and stays ON until the instruction stops being driven. Applicable Inverter *2 *2 *2 *2 *2 *2

3
Components of Positioning Control

Function name Inverter reset Operation mode Running frequency write Run command Inverter status monitor Output frequency [speed]

Instruction Code H0FD H0FB H0ED H0FA H07A H06F

No. of Data Digits 4-digits 4-digits 4-digits 2-digits 2-digits 4-digits

Description Resets the inverter and does not request a response. Inverter reset takes about 2.2 seconds to complete. Sets the communication operation for the inverter. Changes the drive frequency by writing directly to the inverter RAM. Sets forward rotation (STF) or reverse rotation (STR). Monitors operation bits of the inverter. Monitors the frequency of the inverter.

4
Learning to Use FX Positioning Control

*2.

Applicable for all Mitsubishi FREQROL inverters.

41

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

4.2.3

Program example
The following programming example is a hybrid program for FX2N(C) and FX3U(C) controllers to be used with an E500 Series inverter. The travel path and operation pattern are shown below. In the program below, the section Controlling the inverter to move in the forward or reverse rotation direction drives the inverter in the forward or reverse direction. When the forward rotation limit (X001) or reverse rotation limit (X000) is reached, the operation stops. For details on connecting the hardware for testing, refer to the appropriate product manual.
Reverse rotation limit (X000) Forward rotation limit (X001)

General purpose motor

Reverse rotation (H0FA bit2 is ON) Acceleration time (Pr.7) Speed (Hz) 1s

Forward rotation (H0FA bit1 is ON) Deceleration time (Pr.8) 1s

Accel/Decel reference (Pr.20) frequency (Default: 60Hz)

Running frequency (H0ED 40 Hz) Time (s)

Before programming, there are several parameter settings that must be set to the inverter and PLC.

1. Setting communication parameters for the E500 Series inverter

While all operations are stopped (i.e. - the RUN indicator on the E500 is OFF), use the MODE key DOWN keys
Parameter No. Pr.79 Pr.117 Pr.118 Pr.119 Pr.120 Pr.122 Pr.123 Pr.124
MODE

, UP/

and the SET key

Parameter item Operation mode selection

SET

to change and/or confirm the following parameters:

Set value 0 00 to 31 96 10 2 Setting contents External operation mode is selected when power is turned ON. Up to eight inverters can be connected. 9600 bps (default) Data length: 7-bit Stop bit: 1-bit Even parity present Communication check suspension Set with communication data With CR, without LF

Communication station number Communication speed Stop bit / Data length Parity check selection presence/absence

Communication check time interval 9999 Waiting time setting CRLF presence/absence selection 9999 1

42

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

2. Setting communication parameters for the FX2N(C)/FX3U(C) PLC

Parameters are set in GX Developer as shown below. a) Double-click [Parameter] and then [PLC parameter] from the project tree on the left side of the screen. If the project tree is not displayed on the screen, click [View] on the menu bar, and then click [Project Data List].

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

b) Click on the [PLC system(2)] tab in the FX parameter window and set the parameters as shown below:

1 2 3

4
Learning to Use FX Positioning Control

Set CH1 as the channel to be used. Put a checkmark in the [Operate communication setting] checkbox to activate the communication settings. Set [Protocol] to "Non-procedural", [Data length] to "7bit", [Parity] to "Even", and [Stop bit] to "1bit". Set [Transmission speed] to "9600" to match the speed setting in the inverter. Ignore these items.

c) Click the [End] button.

43

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems
d) Create the ladder program as shown below.

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

e) Once the ladder program is complete, click on [Online] from the top menu bar in GX Developer and select [Write to PLC]. The Write to PLC window will appear. f) Click the [Param+Prog] button and then click the [Execute] button. The parameters and the created program will be transferred to the PLC. To enable the transferred parameters, stop the PLC and then restart it.

The following inputs and outputs are used:

Inputs X000 X001 X002 X003 Reverse rotation limit Forward rotation limit Forward rotation command input Reverse rotation command input Y000 Y001 Y002 Y003 Y004 Y006 Y007 Outputs Inverter running (RUN) Forward rotation Reverse rotation Up to frequency (SU) Overload is applied (OL) Frequency detection (FU) Alarm occurrence

M8002
Initial pulse

SET

M10

The write instruction is driven

M10
Driving of write instruction

*Use this for FX3U(C) PLCs

FNC271 IVDR K0 H0FD H9696
Write value

K1
ch.1

The inverter is reset [H9696 "H0FD"]

Inverter Inverter station instruction code number

FNC271 IVDR

K0

H0FB

H2
Write value

K1
ch.1

Inverter Inverter station instruction number code

Computer link operation is specified [H2 "H0FB"]

Writing parameters to the inverter while the PLC is in RUN mode.

*Use this for FX2N(C) PLCs

FNC180 EXTR K11
Function number (Control)

K0

H0FD

H9696
Write value

The inverter is reset [H9696 "H0FD"]

Inverter Inverter station instruction number code

FNC180 EXTR

K11
Function number (Control)

K0

H0FB

H2
Write value

Inverter Inverter station instruction number code

Computer link operation is specified [H2 "H0FB"]

44

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

1
The Basics of Positioning Control

*Use this for FX3U(C) PLCs

FNC 12 MOVP FNC 12 MOVP FNC 12 MOVP FNC 12 MOVP FNC 12 MOVP FNC 12 MOVP FNC 12 MOVP FNC 12 MOVP FNC 274 IVBWR K1 Pr.1 K12000 120 Hz K2 Pr.2 K500 5 Hz K7 Pr.7 K10 1s K8 Pr.8 K10 1s K0 K4 D200 K1
ch.1

D200

The maximum frequency (Pr. 1) is specified The maximum frequency (Pr. 1) is set to "120 Hz" The minimum frequency (Pr. 2) is specified The minimum frequency (Pr. 2) is set to "5 Hz" The acceleration time (Pr. 7) is specified The acceleration time (Pr. 7) is set to "1 sec" The deceleration time (Pr. 8) is specified The deceleration time (Pr. 8) is set to "1 sec" The parameters are written at one time [D200 - D207 Pr. 1, Pr. 2, Pr. 7 and Pr. 8]

D201

2
Positioning by AC Servo System

D202

D203

3
Components of Positioning Control

D204

D205

4
Learning to Use FX Positioning Control

D206

D207

Inverter Write 4 D200 to station parameters D207 number

Writing parameters to the inverter while the PLC is in RUN mode.

*Use this for FX2N(C) PLCs

FNC 180 EXTR K13 K0 K1
Pr.1

K12000
120 Hz

Function Inverter number station (Write) number

The maximum frequency (Pr. 1) is set to "120 Hz" [K12000 Pr. 1] The minimum frequency (Pr. 2) is set to "5 Hz" [K500 Pr. 2] The acceleration time (Pr. 7) is set to "1 sec" [K10 Pr. 7]

FNC 180 EXTR

K13

K0

K2
Pr.2

K500
5 Hz

Function Inverter number station (Write) number

FNC 180 EXTR

K13

K0

K7
Pr.7

K10
1s

Function Inverter number station (Write) number

FNC 180 EXTR

K13

K0

K8
Pr.8

K10
1s

Function Inverter number station (Write) number

The deceleration time (Pr. 8) is set to "1 sec" [K10 Pr. 8]

M8029 "Execution completion" flag

RST

M10

Reset driving of write instruction

45

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

M8002 Initial pulse

SET

M11

The write instruction is driven

M11
Driving of write instruction

FNC 12 MOVP *Use this for FX3U(C) PLCs FNC271 IVDR K0 H0ED

K4000

D10

The opration speed is set as "40 Hz"

40Hz Operation speed

D10

K1

Inverter Inverter Operation ch.1 station instruction speed number code

The preset frequency is written to the inverter [D10 "H0ED"]

*Use this for FX2N(C) PLCs FNC180 EXTR K11 K0 H0ED D10

Setting the operation speed of the inverter to 40 Hz while the PLC is in RUN mode.

Function Inverter Inverter Operation number station instruction speed code (Control) number

The preset frequency is written to the inverter [D10 "H0ED"]

M8029 "Execution completion" flag

RST

M11

Reset driving of write instruction

X000
Reverse rotation limit*1

SET

M15

Operation stop "H0FA" is set to "00H"

X001
Forward rotation limit*1

X002
Forward rotation command input

X000
Reverse rotation limit*1

X001
Forward rotation limit*1

RST

M15

Operation is driven by input X002 or X003

X003
Reverse rotation command input

M15

X002

X003
Reverse rotation command input

Operation Forward rotation stop command input

M21

Forward rotation command b1 of "H0FA" is set to ON Reverse rotation command b2 of "H0FA" is set to ON

Controlling the inverter to move in the forward or reverse rotation direction.

X003
Reverse rotation command input

X002
Forward rotation command input

M22

M8002
Initial pulse

FNC 12 K2M20 MOV

D81

Operation command is withdrawn

FNC228 K2M20 LD<>

D81 Operation command is withdrawn

SET

M12

Changes in the operation commands (M20 to M27) are detected

The write instruction is driven

*1.

The forward and reverse rotation limit switches must be wired so that they are turned ON by default. When either of these limit switches turns OFF (due to the workpiece going out-of-bounds), the inverter operation will be stopped.

46

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

1
The Basics of Positioning Control
*Use this for FX3U(C) PLCs M12
Driving of write instruction

FNC271 IVDR

K0

H0FA

K2M20

K1
ch.1

Inverter Inverter Write station instruction value number code

Operation commands are written. [M20-M27 "H0FA"]

2
Controlling the inverter to move in the forward or reverse rotation direction.
Positioning by AC Servo System

*Use this for FX2N(C) PLCs FNC180 EXTR K11 K0 H0FA K2M20

Function Inverter Inverter Write number station instruction value code (Control) number

Operation commands are written [M20-M27 "H0FA"]

M8029
"Execution completion" flag

RST

M12

Reset driving of write instruction

3
Components of Positioning Control

M10

M11

M12

Driving of Driving of Driving of write write write instruction instruction instruction

MC

*2

N0

M70

While data is not being written to the inverter,data is monitored.

4
Learning to Use FX Positioning Control

N0

M70 *Use this for FX3U(C) PLCs M8000 RUN monitor FNC270 IVCK K0 H07A K2M100 K1
ch.1

Inverter Inverter Read station instruction destinanumber code tion

Inverter status is read [M100-M107 "H07A"]

*Use this for FX2N(C) PLCs FNC180 K10 EXTR

K0

H07A

K2M100

Inverter status is read [M100-M107 "H07A"]

Read Function Inverter Inverter number station instruction destination (Monitor) number code

M100 Inverter running M101 Forward rotation M102 Reverse rotation M103 Up to frequency M104 Overload is applied M106 Frequency is detected M107 Alarm occurrence

Y000 Indicator lamp, etc. Y001 Indicator lamp, etc. Y002 Indicator lamp, etc. Y003 Indicator lamp, etc. Y004 Indicator lamp, etc. Y006 Indicator lamp, etc. Y007 Indicator lamp, etc. Contents of status (according to necessity)

Monitoring operations of the inverter.

*2.

MC denotes the start of a master control block. In this example, the master control block "N0" is only executed when data is not being written to the inverter.

47

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.2 Inverter drive control

*Use this for FX3U(C) PLCs FNC270 IVCK K0 H06F D50 K1

ch.1

Inverter Inverter Read station instruction destinanumber code tion

Monitor frequency value with D50 [D50 "H06F"]

*Use this for FX2N(C) PLCs FNC180 EXTR K10 K0 H06F D50 Monitor frequency value with D50 [D50 "H06F"]

Function Inverter Inverter Read number station instruction destina(Monitor) number code tion

Monitoring operarions of the inverter.

MCR*3

N0 END

*3.

MCR denotes the end of a master control block. In this example, the master control block "N0" is only executed when data is not being written to the inverter.

48

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.3 FX2N-1PG-E positioning

4.3

FX2N-1PG-E positioning
The FX2N(C) and FX3U(C) PLCs support connection with the FX2N-1PG-E special function block. Special function blocks are separate pieces of hardware that can be connected to PLCs to enhance control. Since special function blocks process information separately from the PLC, the scan time of the PLC is not adversely affected during operations controlled by special function blocks. This provides an advantage for programming. Additionally, special function blocks such as the FX2N-1PG-E offer separate, more advanced control through the use of their own inputs and outputs. An important reference for understanding positioning with the FX2N-1PG-E is: FX2N-1PG/FX-1PG Users Manual (JY992D65301) It is assumed that you will have read the above manual or that you will have it nearby for reference.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

4.3.1

Overview of control
The FX2N-1PG-E is a popular unit for performing general point-to-point positioning operations on 1 axis up to 100,000 pulses/second (100 kHz). A stepper motor or servo motor can be used with the FX2N-1PG-E to perform positioning operations. Some of the main advantages to using the FX2N-1PG-E for positioning as opposed to the FX1S, FX1N or FX3U(C) include: the flexible use of the zero point signal PG0, two speed positioning operations with or without interrupt, and the option to choose the FP/RP pulse output method.

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

4.3.2

Important buffer memory locations

The FX2N-1PG-E contains 32 buffer memory (BFM) addresses, which are 16-bit (1 word) areas of memory that contain information relevant to the control of positioning operations. The FX2N(C) or FX3U(C) PLC that is connected to the FX2N-1PG-E can send and receive data to the buffer memory addresses to change and/or update information. This exchange of information takes place through dedicated PLC instructions known as the FROM/TO instructions. (For FX3U(C) PLCs, the MOV instruction can also be used to transfer data to/from special function blocks.) The following buffer memory addresses are used in the ladder program example below. For details on other BFM addresses, refer to the FX-1PG/FX2N-1PG Users Manual (JY992D65301).
BFM # #0 #2, #1 #3 #5, #4 #6 #15 #18, #17 #20, #19 #22, #21 #24, #23 Pulse rate Feed rate Parameters b1, b0 b5, b4 System of units Multiplication factor*1 b1:1, b0:0 b5:1, b4:1 40,000 0 100 100 40,000 150 10,000 M0 M1 M2 M3 M7 (b7=0) D11, D10 M20 M31 D20 Combined system 103 Hz Hz ms mm Hz mm Hz X000 X001 X002 X003 Absolute positioning X007 mm Item Set value 4,000 1,000 PLS/rev m/rev Note

Maximum speed Bias speed Acceleration/ Deceleration time Target address 1 Operating speed 1 Target address 2 Operating speed 2 Operation command b0 b1 Error reset STOP command Forward rotation limit Reverse rotation limit Relative/Absolute positioning

#25

b2 b3 b7 b10

Two speed positioning START command M10

#27, #26 #28 #29

Current address Status information Error code

*1.

Using a multiplication factor of 103 changes the units from m to mm.

49

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.3 FX2N-1PG-E positioning

4.3.3

Program example
In the example that follows, a two speed positioning instruction is used to move a drill 100 mm toward a block of wood with a high speed pulse frequency of 40 kHz. When the drill reaches the wood, the speed decreases to 10 kHz. The drill is then driven for 50 mm into the wood before decelerating to stop.
Drill Wood

M
1PG

High speed

Low speed

The two speed positioning operation is illustrated in the following graph. Neither the zero point return nor the JOG instructions are used in the ladder program.
Frequency (Hz) 40,000 20,000 0 100 Target address 1 BFM #18, #17 50 Target address 2 BFM #22, 21 150 200 Operation speed 1 BFM #20, #19 Operation speed 2 BFM #24, #23

50

100 Distance (mm)

Although the following ladder program is not very complicated, it is important to establish good programming practice by paying attention to the order with which the PLC writes and reads to the buffer memory of the FX2N-1PG-E. Before writing the Operation command (START command) to the modules BFM from the PLC, several settings must be established such as Target addresses 1 & 2, Operation speeds 1 & 2, and various settings such as the bias speed, maximum speed, and the acceleration/deceleration time. The most critical part of the program is the section where the operation commands are enabled by writing bits M0 to M15 to BFM#25. When the positioning START command turns ON, the operation begins with the specified settings. The ladder program example on the following page can be programmed with an FX2N(C) or FX3U(C) PLC and does not require an actuator (i.e., servo system) for testing. The following inputs are used in the program:
Inputs X000 X001 X002 X003 X007 Error reset STOP command Forward rotation limit Reverse rotation limit 2-speed positioning START command

50

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.3 FX2N-1PG-E positioning

1
The Basics of Positioning Control
M8002 Initial pulse FNC79 TO K0 Unit No. K0 BFM # K4000 Pulse rate K1 No. of transfer points K1 No. of transfer points K1 Set the units to m 10 Combined system [H32
3

Set the pulse rate (PLS/rev) [K4000 #0]

FNC79 DTO

K0 Unit No.

K1 BFM #

K1000 Feed rate

Set the feed rate ( m/rev) [K1000 #2,#1]

2
Positioning by AC Servo System
mm #3]

FNC79 TO

K0 Unit No.

K3

H32

BFM # Parameter No. of setting transfer points K4 K40000 K1 Set the maximum speed (Hz) [K40000 #5,#4]

3
Components of Positioning Control

FNC79 DTO

K0 Unit No.

BFM # Maximum No. of speed transfer points K6 BFM # K0 Bias speed K1 No. of transfer points K1 No. of transfer points K1 Set the acceleration/ deceleration time (ms) [K100 #15] Set the bias speed (Hz) [K0 #6]

FNC79 TO

K0 Unit No.

4
Learning to Use FX Positioning Control

FNC79 TO

K0 Unit No.

K15 BFM #

K100 Accel/ Decel time K3M20

M8000 RUN monitor M27 Error flag

FNC78 FROM

K0 Unit No.

K28 BFM #

Read status information [K3M20 #28]

Status No. of Info. transfer M20-M31 points D20 Error code K1 No. of transfer points Read error code [D20 #29]

FNC78 FROM

K0 Unit No.

K29 BFM #

X000 Error reset X001

M0

Reset error

M1
STOP X002

STOP operation

M2
Forward rotation limit*1 X003

Forward rotation limit

M3
Reverse rotation limit*1 M8000

Reverse rotation limit

M7
RUN monitor

Use absolute positioning

*1. The forward and reverse rotation limit switches must be wired so that they are turned ON by default. When these limit switches turn OFF(due the workpiece going out-of-bounds), M2 or M3 will turn ON and cause the pulse operation to stop.

51

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.3 FX2N-1PG-E positioning

X007 START

FNC 79 DTO

K0 Unit No

K17 BFM #

K100 Target address 1

K1 No. of transfer points K1 No. of transfer points K1 No. of transfer points K1 No. of transfer points

Set the Target address 1 [K100 #18,#17]

FNC 79 DTO

K0 Unit No.

K19 BFM #

K40000 Operation speed 1

Set the Operation speed 1 [K40000 #20,#19]

FNC 79 DTO

K0 Unit No.

K21 BFM #

K150 Target address 2

Set the Target address 2 [K150 #22,#21]

FNC 79 DTO

K0 Unit No.

K23 BFM #

K10000 Operation speed 2

Set the Operation speed 2 [K10000 #24,#23]

M10
M8000 RUN monitor

Set the START command for Two-speed positioning

FNC 79 TO

K0 Unit No.

K25 BFM #

K4M0

K1

Operation No. of commands transfer M0-M15 points D10 Current address K1 No. of transfer points

Write operation commands to the FX2N-1PG [K4M0 #25]

FNC 78 DFROM

K0 Unit No.

K26 BFM #

Monitor the current address (mm) [D11,D10 #27,#26]

END

52

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.4 FX2N-10PG positioning

4.4

FX2N-10PG positioning
The FX2N(C) and FX3U(C) PLCs support connection with the FX2N-10PG special function block. As described in Section 4.3, special function blocks are separate pieces of hardware that can be connected to a PLC to enhance control. Due to the separate processing sequence that takes place in special function blocks through the use of buffer memory data, special function blocks provide a distinct advantage to PLC programming through individualized control that expands and improves PLC operations. Additionally, special function blocks such as the FX2N-10PG include extra input points and output points. An important reference for understanding positioning with the FX2N-10PG is: FX2N-10PG Users Manual (JY992D93401) It is assumed that you will have read the above manual or that you will have it nearby for reference.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

4.4.1

Overview of control
The FX2N-10PG is used to perform point-to-point positioning operations on 1 axis up to 1,000,000 pulses/ second (1 MHz). With the FX2N-10PG differential line driver type outputs that provide improved stability and better noise immunity, a stepper motor or servo motor can be controlled to perform a variety of positioning operations including multi-speed positioning and interrupt stop positioning. The controller also supports the connection of a manual pulse generator dial to control individual pulses from a position dial. Another advantage to using the FX2N-10PG is the ability to use a defined set of positioning operations in table format with up to 200 predefined table operations.

4
Learning to Use FX Positioning Control

4.4.2

Important buffer memory locations

The FX2N-10PG contains 1,300 buffer memory (BFM) addresses, which are 16-bit (1 word) areas of memory that contain information relevant to the control of positioning operations. Most of these addresses are reserved for data to be used in table operations. The FX2N(C) or FX3U(C) PLC that is connected to the FX2N10PG can send and receive data to the buffer memory addresses to change and/or update information. This exchange of information takes place through dedicated PLC instructions known as the FROM/TO instructions. (For FX3U(C) PLCs, the MOV instruction can also be used to transfer data to/from special function blocks.) The following buffer memory addresses are used in the ladder program example below. For details on other BFM addresses, refer to the FX2N-10PG Users Manual (JY992D93401).
BFM # #1, #0 #2 #11 #12 #14, #13 #16, #15 #25, #24 Maximum speed Bias speed Acceleration time Deceleration time Target address 1 Operation speed 1 Current address Operation command b0 b1 #26 b2 b3 b8 b9 #27 #28 #33, #32 #35, #34 b0 Error reset STOP Forward rotation limit Reverse rotation limit Relative/Absolute positioning START command 1-speed positioning operation M20 M31 4,000 1,000 PLS/rev m/rev M0 M1 M2 M3 M8 (b8 =1) M9 X000 X001 X002 X003 Relative positioning X007 Item 0 100 100 50 50,000 D11, D10 Set value 50,000 Hz Hz ms ms mm Hz mm Note

Operation pattern Status information Pulse rate Feed rate

53

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.4 FX2N-10PG positioning

BFM # Parameters #36 #37

Item b1, b0 System of units b5, b4 Multiplication Error code factor*1

Set value b1:1, b0:0 b5:1, b4:1 D20

Note Combined system 103

*1.

Using a multiplication factor of 103 changes the units from m to mm.

4.4.3

Program example
In the program example that follows, a series of three individual 1-speed positioning operations are controlled from the FX2N-10PG with an output signal from the PLC that turns ON between each operation. An event timing chart is included on the next page to help understand the logic flow of the program. This example uses a conveyor system to carry boxes from one location to another. Each intermittent positioning operation positions a box in front of a scanner to scan it for 2 seconds. During each 2-second scan, Y000 from the PLC turns ON to illuminate an indicator light. The number of boxes to be scanned can be varied by changing the value of the counter, C100, in the program.
Barcode scanner

M 10PG

Conveyor belt

The positioning pattern is shown in the following figure. Neither the zero point return nor the JOG instructions are used in the ladder program example.
Frequency (Hz) 50,000 25,000 0 Target address 1 BFM #14, #13

Operation speed 1 BFM #16, #15

50

100 Distance (mm)

150 200 Y000 turns ON for 2 sec.

In order for the program to function correctly for the specified number of repetition cycles, the START command input (X007) must not be turned ON again during the positioning operation. If the START command is turned ON again, the counter C100 is reset, which clears the number of repetitions.

54

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.4 FX2N-10PG positioning

The following program can be used with an FX2N(C) or FX3U(C) PLC and does not require an actuator (i.e., servo system) for testing. The input and output points include:
Inputs X000 X001 X002 X003 X007 Error reset STOP command Forward rotation limit Reverse rotation limit START command Y000 Outputs Indicator lamp (ON for 2 sec. intervals)

1
The Basics of Positioning Control

2
Positioning by AC Servo System

The following figure is an event timing chart for part of the operation in the program below.
X007 (START) M9 (START command) C100 T0 M26 (Positioning Complete Flag) Y000 2 sec. One operation cycle
*1

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

Positioning complete

*1.

The positioning complete flag will only be ON at the very beginning of the program when it is not the first time to operate the equipment and the power has not been recycled.

55

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.4 FX2N-10PG positioning

M8002 Initial pulse

FNC 79 DTO

K0

K32

K4000 Pulse rate

K1 No. of transfer points K1 No. of transfer points K1

Set the pulse rate (PLS/rev) [K4000 #1, #0]

Unit No. BFM #

FNC 79 DTO

K0 Unit No.

K34 BFM #

K1000 Feed rate

Set the feed rate ( m/rev) [K1000 #35, #34]

FNC 79 TO

K0

K36

H32

Unit No. BFM # Parameter No. of setting transfer points FNC 79 DTO K0 Unit No. K0 K50000 K1

Set the units to m 103 Combined system [H32 #36]

mm

Set the maximum speed (Hz) [K50000 #1,#0]

BFM # Maximum No.of speed transfer points K2 BFM # K0 Bias speed K1 No.of transfer points K1 No. of transfer points K1 No. of transfer points K1 Read status information [K3M20 #28] Set the deceleration time (ms) [K100 #12] Set the acceleration time (ms) [K100 #11] Set the bias speed (Hz) [K0 #2]

FNC 79 TO

K0 Unit No.

FNC 79 TO

K0 Unit No.

K11 BFM #

K100 Accel time

FNC 79 TO

K0 Unit No.

K12 BFM #

K100 Decel time K3M20

M8000 RUN monitor M25 Error flag

FNC 78 FROM

K0 Unit No.

K28 BFM #

Status No. of Info. transfer M20-M31 points D20 Error code K1 No.of transfer points M0 Reset error Read error code [D20 #37]

FNC 78 FROM

K0 Unit No.

K37 BFM #

X000 Error reset X001 M1 STOP X002 M2 Forward rotation limit *1 X003 M3 Reverse rotation limit *1 Reverse rotation limit Forward rotation limit STOP operation

*1.

The forward and reverse rotation limit switches must be wired so that they are turned ON by default. When these limit swiches turn OFF (due to the workpiece going out-of-bounds), M2 or M3 will turn ON and cause the pulse operation to stop.

56

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.4 FX2N-10PG positioning

1
The Basics of Positioning Control
M8000 M8 RUN monitor X007 M9 START T0 2-sec. timer M8002 Initial pulse FNC 79 TO K0 K27 H1 K1 Set 1-speed positioning [H1 #27] START positioning Use relative positioning

2
Positioning by AC Servo System

3
Components of Positioning Control

Unit No. BFM #

1-speed No. of positioning transfer points

FNC 79 DTO

K0

K13

K50

K1

Set the Target address 1 [K50 #14,#13]

Unit No. BFM #

Target No. of address 1 transfer points

4
Learning to Use FX Positioning Control

FNC 79 DTO

K0

K15

K50000
speed 1

K1
No. of transfer points

Set the Operation speed 1 [K50000 #16,#15]

Unit No. BFM # Operation

T0 2-sec. timer M26

X001 STOP

M25 Error flag

K2 C100 Counter to repeat operation 2 times

C100 Y000 Y000 indicator light

Positioning Counter complete flag T0

K20 2 second timer

X007 RST START M8000 RUN monitor C100 Reset C100

FNC 79 TO

K0 Unit No.

K26

K4M0

K1

Write operation commands to the FX2N-10PG [K4M0 #26]

BFM # Operation

No. of commands transfer M0-M15 points

FNC 78 DFROM

K0 Unit No.

K24 BFM #

D10
Current address

K1
No. of transfer points

Monitor the current address (mm) [D11,D10 # 25,#24]

END

57

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

4.5

FX2N-10GM and FX2N-20GM positioning

The FX2N-10GM and FX2N-20GM controllers (also referred to as the 10GM and 20GM) are unique in that they can operate as individual stand-alone units with their own programming language, power supplies and separate sets of inputs and outputs. This means that the 10GM and 20GM can be used with or without a PLC to control logic instructions and standard positioning operations. Important references for understanding positioning with the FX2N-10GM and FX2N-20GM are: FX2N-10GM/FX2N-20GM Hardware/Programming Manual (JY992D77801) FX-PCS-VPS/WIN-E Software Manual (JY992D86801) It is assumed that you will have read and understood the above manuals or that you will have them nearby for reference.

4.5.1

Overview of control
Along with the capability to be used for independent control, the FX2N-10GM (1 axis of control) and FX2N20GM (2 axes of control) can be used as special function blocks in conjunction with an FX2N(C) or FX3U(C) PLC to transfer data back and forth via dedicated buffer memory addresses. These addresses overlap with and replace the special M and special D registers in the 10GM and 20GM. One particular advantage to using a PLC with the FX2N-10GM is the ability to use the table method where up to 100 positioning operations can be defined and saved for consecutive execution. The FX2N-10GM and FX2N-20GM output pulse trains to control a stepper/servo motor with a maximum output frequency of 200,000 pulses/second (200 kHz). This offers the same speed as the FX3U high speed positioning adapters, except that the GM controllers use open collector type outputs instead of differential line driver type. Combined with standard positioning operations such as 1-speed and 2-speed positioning, the 10GM and 20GM include an electrical zero return function to return the motor(s) to a specific user-defined address without the use of a hardware DOG switch. This feature is unique since it is not available with any of the other FX Series controllers. The main differences between the FX2N-10GM and FX2N-20GM are listed in the following table.
FX2N-10GM Inputs/Outputs Expandable I/O Memory type Memory size Table method 4 inputs, 6 outputs No EEPROM 3.8K steps Yes CON1: Control + I/O CON2: Axis1 FX2N-20GM 8 inputs, 8 outputs Yes (48 additional I/O) Built-in RAM (RAM has battery backup) (EEPROM cassette optional) 7.8K steps No CON1: I/O CON2: Control CON3: Axis1 CON4: Axis2

Connectors

4.5.2

Using dedicated software to set positioning for the FX2N-20GM

In the example that follows, an FX2N-20GM is used with the FX-PCS-VPS/WIN-E software to perform positioning on two axes. The FX-PCS-VPS/WIN-E software (also referred to as VPS) is beneficial for defining positioning parameters and setting positioning operations. Operations can be visually organized in a flow chart format and a monitoring window can be configured with user-defined objects. To test operations with an FX2N-20GM, an actuator (i.e., servo system) and PLC are not required. For information on the cables necessary to connect an FX2N-20GM to a personal computer for programming, refer to the FX2N-10GM/FX2N-20GM Hardware/Programming Manual (JY992D77801).

58

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

1. Operation objective
The objective of this example is to use the FX2N-20GM to trace a path using 1-speed, linear interpolation, and circular interpolation operations. Path of travel
270

1
The Basics of Positioning Control

2
Positioning by AC Servo System

Start point A G C H END point F

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

B 0 270

Operation Details
Point A B C D E F G H Coordinate (X, Y) (0, 0) (80, 100) (110, 200) (200, 200) (200, 100) (150, 100) (150, 70) End point Description This point can be anywhere. Move to zero point, wait for 2 seconds Output Y0 turns ON, wait for 2 seconds Output Y0 turns OFF, wait for 2 seconds

The output Y0 is used to imitate a pen, or other end effector. Each point-to-point operation is described as follows: (A to B) Return to Electrical Zero (B to C) High speed positioning (C to D) Linear interpolation (D to E) High speed positioning (E to F) Clockwise circular interpolation (F to G) High speed positioning (G to H) High speed positioning

2. Getting started with FX-PCS-VPS/WIN-E

Open a new file with VPS and choose [FX(2N)/E-20GM with simultaneous 2 axis]. This setting allows for linear and circular interpolation operations to be placed on a flow chart for positioning. Take a minute to familiarize yourself with the layout and menu items of the software. The panel on the left side of the screen is required for selecting the [Flow], [Code], and [Func] components to place into the Flow Chart window. To place an item into the Flow Chart window, click on the item once and then click anywhere within the Flow Chart window. Once an item has been placed in the Flow Chart window, it can be dragged to any position. Items are connected by using the wire tool to drag a wire between each item.

59

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

3. Creating a Flow Chart

The flow chart below demonstrates basic positioning using the FX2N-20GM. Since this program is designed to be used without a mechanical plotter, an electrical zero point is used for reference. Re-create the diagram below by using the [Code] and [Func] buttons on the left panel of the VPS software to select and place each function block.

Many programs can be stored in a GM controller at one time. This example uses program number 0.

The "DRV Ret" command is used to move from the start point to the electrical zero point.

Here, the program waits for 2 seconds, using a 10ms timer.

This command indicates a high speed positioning command to position C.

Here, Y0 is turned ON to mimic the use of an end effector tool.

This timer allows for a tool to be activated, or for an operation to be executed.

This command is the start of a continuous steady path using linear interpolation to position D.

Only the X-axis is used in this 1-speed positioning instruction to move to position E.

For a smooth arc to position F, circular interpolation is used. This example shows the start and end positions as well as the radius (r) and speed (f).

Only the X-axis is used in this 1-speed positioning instruction to move to position G.

Here, Y0 is turned OFF to mimic the end of use for an end effector.

A timer is used to ensure the end effector operation has finished completely.

This command rapidly moves the Y-axis for a short distance so that it can reach position H.

This denotes the end of the program, where the controller waits for the next start command.

60

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

4. Creating a Monitor Window

Along with the flow chart, create a monitoring window similar to the one shown below. All of the items on the monitoring window can be found using the [Insert] menu at the top of the screen.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

The following items from the [Insert] menu are used:

Item Current Position Plotting Device Status Rectangle Description This displays (monitors) the current address during positioning. Double click on the plot area to change the scale. Select Y0, 1 point. Create a rectangle around Y000 by selecting the rectangle button from the drawing toolbar at the top of the screen. While the rectangle is selected, the background color can be changed by pressing the [B] Brush Color button. X-axis Start Manual Operation Stop + Jog - Jog FX-GM Status Y-axis Start Stop + Jog - Jog

This is a lamp that automatically monitors positioning operations.

61

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

5. Setting parameters
In addition to the preparation of a positioning program, diversified parameters should be set in the FX2N20GM. In this example, only a few parameters need to be set. (When working with various equipment such as a mechanical plotter that uses an X-Y plotting table, the parameters should be set in accordance with the mechanism being used. These settings depend on the specific plotter type and should be located in the documentation provided with the plotter.) Below are the four positioning parameter windows from VPS. The settings on these windows should be copied for BOTH the X- and Y- axes before performing positioning. First, open the Parameter Units window by selecting [Parameters] [Positioning] [Units] from the main menu bar at the top of the screen.

Specify the same settings for the Y-axis.

Next, open the Parameter Speed window by selecting [Parameters] [Positioning] [Speed] from the menu bar at the top of the screen.

Specify the same settings for the Y-axis.

The [Max speed] is set very low in order for the VPS software to trace the path during operation through the Monitoring Window. In turn, both the JOG speed and interpolation value must be reduced. (In practice, it is impossible to have the JOG speed set to a value higher than the Max speed setting.)

62

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

Next, open the Parameter Machine Zero window by selecting [Parameters] [Positioning] [Machine Zero] from the menu bar at the top of the screen.

1
The Basics of Positioning Control

Specify the same settings for the Y-axis.

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

Since mechanical hardware will not be connected to the FX2N-20GM for this example, it is not necessary to configure the limit switch and DOG switch settings in the parameters. It is, however, necessary to reduce the [Creep speed] and the [Zero return speed]. For the last parameter screen, open the Parameter Settings window by selecting [Parameters] [Positioning] [Settings] from the menu bar at the top of the screen.

NO CHANGES

None of the parameters in the Parameter Settings window need to be changed. When using a mechanical plotter, however, these settings become more important.

63

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

4.5.3

Testing and monitoring operations

After setting the parameters and defining the positioning travel paths described in the previous section, testing can be performed as follows. Check the communication between the FX2N-20GM and the personal computer by selecting [FX-GM] [Com Port] and then the [Test] button. Make sure the GM unit is in MANU mode by checking the hardware switch on the unit. Download the project by selecting [FX-GM] [Write to FX-GM] from the menu bar at the top of the screen and select the [Write after saving file] button. The program will be downloaded to the 20GM. In VPS, start the Monitor mode by clicking the Monitor icon on the tool bar as shown below.

Monitor icon

The monitor mode window will appear with three windows:

Monitoring window X-axis and Y-axis Monitor Mode Sub-Task Monitor Mode This window is not needed since there are not any sub-routines being used. This window can be minimized to create more space on the screen. At first, this window will be empty, but This is the window that has already as soon as the program is started, the been created where the unit will be flow chart will appear. Each controlled and monitored from. positioning operation will be highlighted in RED as it is performed.

After minimizing the Sub-Task Monitor Mode window, resize the Monitoring Window and X-axis and Yaxis Monitor Mode windows.

Before starting the operation, it is necessary to set the start point. This can be done by using the [X JOG+] and [Y JOG-] buttons or by double clicking on the current position [X: 0 Y: 0] display. Double click the current position display in the Monitoring window to set the start point.

After editing the current address to X: 50 and Y: 125, click on the [Write to FX-GM] button for each axis.

As the address information is changed, red lines will appear on the plotter. This shows the current position. To clear these red lines before positioning, double click on the plotting area, and then click on the [Clear] button.

64

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.5 FX2N-10GM and FX2N-20GM positioning

The next step is to switch the FX2N-20GM to AUTO mode by moving the switch on the unit to AUTO. Finally, on the Monitoring Window screen, click on either the [X START] or [Y START] buttons. The positioning operation will be performed and the plot result should look identical to the one shown in the following picture.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

To run the program again, set a new start position (or let it start from where it is), clean the plot area, and press the [X START] or [Y START] button again. If the plot does not look like the one above, check the flow chart program against the program listed in Section 4.5.2 (3).

65

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

4.6

FX3U-20SSC-H positioning
The FX3U(C) PLC supports connection with the FX3U-20SSC-H special function block, which is an advanced module to perform positioning operations on two axes using Mitsubishis fiber optic communication servo network known as SSCNET III (Servo System Controller Network). Important references for understanding positioning with the FX3U-20SSC-H include: FX3U-20SSC-H Users Manual (JY997D21301) FX Configurator-FP Operation Manual (JY997D21801) It is assumed that you will have read the above manuals or that you will have them nearby for reference.

4.6.1

Overview of control
Using an FX3U PLC with the FX3U-20SSC-H (20SSC-H) module and two Mitsubishi MR-J3-B servo amplifier systems, high speed positioning with pulse output frequencies up to 50,000,000 pulses/second (50 MHz) is possible on two axes. However, since motors compatible with the MR-J3-B servo amplifier system have a maximum rated speed of 6,000 RPM, the maximum controllable speed from the 20SSC-H becomes:
6,000 rev min 262,144 PLS rev 1 PLS = 26,214,400 60 sec

The FX3U-20SSC-H provides several advantages compared to other controllers in the FX family:
FX3U-20SSC-H Feature Bidirectional communication Wiring Advantage With SSCNET III, the PLC can communicate with the servo amplifier to monitor torque, servo status flags, servo parameters and absolute position data. Easy to use wiring. High immunity to noise from external devices. Long distance wiring (50m). Software Easy setup of parameters and table data (up to 300 table operations per axis). Convenient use of monitoring and testing functions.

With the use of a built-in Flash ROM, the FX3U-20SSC-H can store data permanently via non-volatile storage. Since the flash memory transfers all of its data to the buffer memory of the 20SSC-H each time the power is turned ON, the flash memory provides extra benefit for applications requiring a default set of data to be automatically loaded. This eliminates the need to use a PLC program for setting parameters and table data, which can greatly simplify the length and complexity of a ladder program. The FX3U-20SSC-H includes an input connector to connect manual pulse generator dials and various switches such as the START, DOG, and interrupt switches. These inputs assist in controlling positioning operations and are necessary to operate instructions such as the interrupt 1-speed constant quantity feed instruction and the DOG type mechanical zero return command.

66

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

4.6.2

Using dedicated software to set positioning for the FX3U-20SSC-H

In the example that follows, an FX3U-20SSC-H is used with FX Configurator-FP to perform positioning on two axes with an XY-axis table operation. FX Configurator-FP is convenient for defining servo parameters, positioning parameters and table information. It is also recommended to be used whenever possible since the use of a sequence program for setting parameters and table data requires many steps and devices, resulting in a complex program and increased PLC scan time. Different from other FX positioning controllers, the FX3U-20SSC-H requires connection to a servo system to perform positioning. For details on connecting an MR-J3-B servo system, refer to the appropriate servo manual.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

1. Setting parameters
Prior to setting positioning parameters and servo parameters, check to verify the connection between the PLC and the personal computer is valid. Since ladder logic in the PLC is not used in this example, set the RUN/STOP switch on the PLC to [STOP]. a) Open a new file in FX Configurator-FP by clicking on the [Make new file] button.

3
Components of Positioning Control

b) Expand the tree of folders in the [File data list] panel on the left-hand side of the screen by double clicking on [Unset file / FX3U-20SSC-H], [Edit], and then [Monitor]. c) Go to [Online] [Connection setup] [Comm. Test] Verify that the devices are communicating properly. d) Double click on [Positioning parameters] in the [File data list] panel on the left-hand side of the screen to modify the positioning parameters. Set items in the [Item] column for both the X- and Y- axes as shown:

4
Learning to Use FX Positioning Control

e) Next, double click on [Servo parameters] in the [File data list] panel on the left-hand side of the screen to modify the servo parameters. Set items from the [Kind] column for both the X- and Y- axes as shown:

67

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

2. Creating XY-axis table operation data

Double click on [XY-axis Table information] in the [File data list] panel on the left-hand side of the screen to open the XY table. Maximize the window to enter the following data:
Address x:[PLS] y:[PLS] Speed fx:[Hz] fy:[Hz] Arc center i:[PLS] j:[PLS] Time [10ms] Jump No. m code -1 20,000,000 10,000,000 -1 -1 -1 5,000,000 5,000,000 30 positioning positioning at at 2-step 2-step 10,000,000 -10,000,000 -10,000,000 10,000,000 10,000,000 10,000,000 10,000,000 10,000,000 30 positioning positioning at at 2-step 2-step 10,000,000 -10,000,000 -10,000,000 10,000,000 10,000,000 10,000,000 10,000,000 10,000,000 30 0 0 7,000,000 5,000,000 5,000,000 30 positioning positioning at at 2-step 2-step 10,000,000 5,000,000 -5,000,000 -10,000,000 15,000,000 7,500,000 7,500,000 15,000,000 30 20,000,000 -20,000,000 150 0 26,214,400 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1

No.

Command Code

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Incremental address specification X-axis positioning at 1-step speed Y-axis positioning at 1-step speed XY-axis speed positioning at 1-step

20,000,000 5,000,000 -5,000,000 0 0

10,000,000 2,000,000 2,000,000 15,000,000

Circular interpolation (CNT,CW) Dwell XY-axis speed XY-axis speed Dwell XY-axis speed XY-axis speed Dwell Circular interpolation (CNT,CCW) Dwell XY-axis speed XY-axis speed Dwell Linear interpolation Dwell Jump End

68

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

3. Writing data to the FX3U-20SSC-H

Write the servo parameters, positioning parameters and table information to the FX3U-20SSC-H BFM and Flash ROM by pressing the [Write to module] button and placing check marks in the following boxes. Change the range of table data to be written to 0 - 25.

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

Next, reset the module by pressing the [System reset] parameters.

button. This is necessary to refresh the servo

69

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

4.6.3

Testing and monitoring operations

With the parameters and table information saved to the FX3U-20SSC-H module from Section 4.6.3 and the PLC in STOP mode, testing is performed by using TEST MODE in FX Configurator-FP. First, enter TEST MODE by pressing the [Test On/Off] button. button to display the X-axis Operation After entering TEST MODE, click on the [Operation Test X-axis] test window.

Next, select the [XY-axis table operation] from the [X-axis] [Pattern] combination box and click on the [Start] button to begin positioning. Note that because the table operation includes a "Jump" command, the operation will continuously loop from row 0 to row 20.

To stop positioning, click on the [All axis stop] or [Stop] button. After stopping the table operation, a variety of other positioning operations can be tested from the [X-axis] [Pattern] combination box such as 1-speed positioning, 2-speed positioning, and linear interpolation. For additional control in TEST MODE, the tabs at the top of the "X-axis Operation test" window can be used according to the following information:
Position start Positioning operations can be executed from this window. Target address and operation speed data is defined here. Feed present value CHG The value of the current address can be changed using this window. Speed CHG Two operations for changing the speed of the motor are available from this window. OPR By clicking on the [REQ. OPR] button, zero return is executed. JOG/MPG JOG operation and manual pulsar operation testing can be performed from this window.

70

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

4.6.4

Important buffer memory locations

The FX3U-20SSC-H buffer memory includes five separate data areas for: Monitor data, Control data, Table data, Positioning parameter data, and Servo parameter data. With "read only" or "read/write" access, buffer memory addresses use bit and word information to control positioning operations. Similar to the FX2N-10PG, a large percentage of the BFM is dedicated to the control of table positioning operations.
Monitor data Control data Table information Positioning parameters Servo parameters Used to monitor the Used to control current position, positioning statuses, etc. operations. Used to store Used to store parameters Used to store predefined table data. such as the max. speed parameters relevant to and accel/decel times. the servo(s).

1
The Basics of Positioning Control

2
Positioning by AC Servo System

The following buffer memory addresses are used in the ladder program example below. For details on other BFM addresses, refer to the FX3U-20SSC-H Users Manual (JY997D21301).
BFM Area BFM # #1, #0 Monitor data #101, #100 #28 #128 #501, #500 #503, #502 X-axis current address Y-axis current address X-axis status information Y-axis status information X-axis Target address 1 X-axis Operation speed 1 X-axis Operation command 1 b0 b1 b2 b3 #518 b4 b5 b6 Control data b8 b9 #618 b0 b6 #519 b4 b0 b10 #521 Positioning parameter data #14013, #14012 Error reset STOP Forward rotation limit Reverse rotation limit Forward rotation JOG(+) Reverse rotation JOG(-) Zero-return Relative/Absolute positioning START command Error reset Zero-return Item Set value D1, D0 D101, D100 D10 D110 10,000,000 2,000,000 M0 - M15 M0 M1 M2 M3 M4 M5 M6 M8 (b8 =1) M9 M100 - M115 M100 M106 M20 - M35 X001, X002 X004 X005 Table row #0 Hz (PLS/sec) X007 X003 X007 X006 X000 X010 X001 X002 X003 Relative positioning X004, X005 PLS Hz (PLS/sec) PLS PLS Note

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

Y-axis Operation command 1

X-axis Operation command 2 X-axis Operation pattern selection

Positioning parameter enable command M24 1-speed positioning Table operation (simultaneous) H1 H400 0 1,000,000

#520

Table operation start number X-axis JOG speed

71

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

4.6.5

Program example
The following program uses buffer memory communication to perform JOG positioning, 1-speed positioning, and table operation control. The XY-table created in the previous section can be used in this example. For this example, FX Configurator-FP should be used to specify the servos, change the maximum speed, and to set the zero return mode as described in Section 4.6.2. The ladder program is to be used with an FX3U(C) PLC and MR-J3-B servo system. Without these components, the program cannot be tested. Input points from the PLC include:
Inputs X000 X001 X002 X003 X004 X005 X006 X007 X010 X-axis Forward rotation limit X-axis Forward rotation JOG(+) X-axis Reverse rotation JOG(-) X- and Y-axis Zero return START command (X-axis 1-speed operation) START command (XY-axis Table operation) STOP command Error reset X-axis Reverse rotation limit

M8000 RUN monitor

FNC 12 DMOV

U0\ G0 BFM #

D0 X-axis current address D100 Y-axis current address D10 X-axis status information D110 Y-axis status information M2

Monitor X-axis current address [D1,D0 #1,#0]

FNC 12 DMOV

U0\ G100 BFM #

Monitor Y-axis current address [D101,D100 #101, #100]

FNC 12 MOV

U0\ G28 BFM #

Monitor X-axis status info. [D10 #28]

FNC 12 MOV

U0\ G128 BFM #

Monitor Y-axis status info. [D110 #128]

X000 Forward rotation limit *1 X010 Reverse rotation limit *1 X001 X-axis JOG(+) X002 PLS X-axis JOG(-) FNC 12 DMOVP

X-axis Forward rotation limit

M3

X-axis Reverse rotation limit

K100000 X-axis JOG speed

U0\ G14012 BFM #

Set the X-axis JOG speed (Hz) [K100000 #14013, #14012]

M24 Positioning parameter enable command

Enable the X-axis JOG speed

*1.

The forward and reverse rotation limit switches must be wired so that they are turned ON by default. When these limit switches turn OFF (due to the workpiece going out-of-bounds), M2 or M3 will turn ON and cause the pulse operation to stop.

72

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

1
The Basics of Positioning Control
M8000 RUN monitor X001 X-axis JOG(+) X002 X-axis JOG(-) X003 PLS Zero return M6 X-axis zero return X002 X-axis JOG(-) X001 M5 X-axis JOG(+) X-axis JOG(-) operation is being performed FNC 12 MOV U0\ G519 X-operation BFM # command 2 M20-M35 K4M20 M4 Write X-axis Operation command 2 [K4M20 #519]

X-axis JOG(+) operation is being performed

2
Positioning by AC Servo System

3
Components of Positioning Control

PLS X004 X-axis 1-speed operation X005 XY-axis Table operation

M106

Y-axis zero return

4
Learning to Use FX Positioning Control

FNC 12 MOVP

H1 X-axis 1-speed positioning

U0\ G520 BFM #

Set X-axis 1-speed positioning [H1 #520]

FNC 12 DMOVP

U0\ G500 X-axis Target BFM # address 1 K10000000 K2000000 X-axis Operation speed 1 U0\ G502 BFM #

Set X-axis Target address 1 [K10000000 #501, #500]

FNC 12 DMOVP

Set X-axis Operation speed 1 [K2000000 #503, #502]

M8 X005 XY-axis Table operation X004 X-axis 1-speed operation

Use relative positioning

FNC 12 MOVP

U0\ G520 XY-Table BFM # operation (simultaneous) H400 U0\ G521 XY-Table BFM # row #0 K0

Set XY-axis simultaneous Table operation [H400 #520]

FNC 12 MOVP

Set starting row No. for XY-Table operation [K0 #521]

X004 PLS X-axis 1-speed operation X005 XY-axis Table operation M9 START positioning

73

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

X006 M1 X-axis STOP X007 PLS Error reset M0 Reset X-axis error STOP operation

PLS

M100

Reset Y-axis error

M8000 RUN monitor FNC 12 MOV

U0\ G518 X-operation BFM # command 1 M0-M15 K4M0 U0\ G618 Y-operation BFM # command 1 M100-M115 K4M100 END

Write X-axis Operation command 1 [K4M0 #518]

FNC 12 MOV

Write Y-axis Operation command 1 [K4M100 #618]

74

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems

4 Learning to Use the FX Family for Positioning Control

4.6 FX3U-20SSC-H positioning

MEMO

1
The Basics of Positioning Control

2
Positioning by AC Servo System

3
Components of Positioning Control

4
Learning to Use FX Positioning Control

75

FX Series Programmable Controllers

Introduction to FX Positioning Control Systems
Revised History

Revised History
Date 11/2007 Revision A First Edition Description

76

HEAD OFFICE: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN HIMEJI WORKS: 840, CHIYODA CHO, HIMEJI, JAPAN

HIME-SH006-A0711(MEE)

Effective Nov. 2007 Specifications are subject to change without notice.