Scribd
Upload
511 views

MCB 51-2 Quick Start Guide 1

The document provides instructions for setting up and verifying the correct operation of an ESA MCB 51-2 evaluation board. It includes a list of included parts, quick steps for assembly which involve unpacking parts, attaching cables to power the board, and installing software. Settings are described for running the board in USB, external UART, and ISP modes to communicate with a computer and program on-chip flash memory.

Uploaded by

GAUTI2212
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
511 views

MCB 51-2 Quick Start Guide 1

The document provides instructions for setting up and verifying the correct operation of an ESA MCB 51-2 evaluation board. It includes a list of included parts, quick steps for assembly which involve unpacking parts, attaching cables to power the board, and installing software. Settings are described for running the board in USB, external UART, and ISP modes to communicate with a computer and program on-chip flash memory.

Uploaded by

GAUTI2212
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

ESA MCB 51-2

EVALUATION BOARD

Quick Start Guide


This document describes a series of quick steps to bring up and verify correct operation of your new ESA MCB 51-2 board. All the elements you will need to complete this assembly are provided with board. The set of steps involve unpacking and identifying each part in the MCB 51-2, attaching a minimum subset of cables required to verify operation, and powering the board. The ESA MCB 51-2 Kit contains all the pieces necessary to bring up and verify correct operation of your ESA MCB 51-2 board. The following table lists the elements of the ESA MCB 51-2 Development : No. 1 2 3 4 5 Item MCB51-2 Board Power cable with Jack Connector(3.5 mm barel) Jack Power Cable with Jack(3.5 mm barrel) USB Cable(A to B) Driver CD User Manual

Quick List of Assembly Steps


1. Install Keil Development tools for 8051 microcontroller. *Driver CD contains Evaluation version of Keil tools. 2. Connect 5V DC power supply to board using power jack. 3. Connect Provided USB cable between MCB 51-2 board & computer. 4. Jumper & DIP switch settings for USB mode(Internal UART ) A.DIP Switch settings DIP S/W No. 1(UART INT) 2(EXT UART) 3(MONITOR) 4(LED) 5(INT0) 6(NC) 7(NC) 8(NC) Position OFF OFF ON ON ON ON ON DON'T CARE

B. JUMPER settings

JUMPER JP1 JP2 JP3-JP5

Position OPEN BC(CLOSED) CLOSED WHEN USING ONBOARD SPI MEMORY

5. 6. 7. 8.

Start Vision IDE. Open Sample program Blinky which you can get in Kiel folder ->Example->Blinky Open Target options & select device AT89c51ED2. Go to Debug tab and select the options as shown below.(By default some of the options are selected)

7. Go to Settings option near Use: Keil Monitor-51 Driver and select the options as shown below.(By default all the options are selected) *Please select Baud Rate 38400 for USB mode & select appropriate COM port.

8. Now build the program using build option. 9. Ensure that the power supply for the board is switched ON. Press RESET button on the ESA MCB51-2 board just to make sure that the target board is ready for downloading the built program. 10. To download & debug the built program we have to launch the debugger. Go to Debug-> Start/Stop Debug option a, and click on it. 11. After enter into debug mode click on RUN option you can see all LEDs of MCB51-2 board are blinking. Settings For External UART mode: 1. Jumper & DIP switch settings for External UART mode A.DIP Switch settings DIP S/W No. 1(UART INT) 2(EXT UART) 3(MONITOR) 4(LED) 5(INT0) 6(NC) Position OFF ON ON ON ON ON

7(NC) 8(NC)

ON DON'T CARE

B. JUMPER settings *Same as in USB mode. 2. Connect ESA MCB51-2 board with computer using RS232 cable. 3. Set the BAUD rate to 57600. 4. Other settings are same as USB mode. Settings For ISP mode: 1. Jumper & DIP switch settings for UART mode A. DIP switches are not effective in this mode(Don't care). B. JUMPER settings

JUMPER JP1 JP2 JP3-JP5

Position CLOSED BA(CLOSED) DON'T CARE

2 .Use ATMEL FLIP flash programming utility to program onchip flash of AT89c51ED2. *Use provided USB cable to connect ESA MCB51-2 with the computer. Settings to use onboard SPI memory: 1. Keep the jumpers JP3-JP5 in closed position. 2. All other settings are same as USB mode.

Note: If still you are facing any problem then please contact to ESA support team at Email : [email protected] Phone :080-23577924

You might also like