MV Relais : SEPAM generalities

Jun-2012 By Y. NICOLAS Schneider Electric BU Infrastructure - PEC

Usual ANSI codes for current protection

3 CT by SEPAM 50 51 : Phase overcurrent 50N-51N / 50G-51G : Earth fault / sensitive earth fault 49RMS : Thermal overload With CSH200 on 3 phases With CSH120 on neutral

67 : Directional phase overcurrent 67N : Directional earth fault 64REF : Restrictive earth fault 87T : transformer differential 87 M : Machine differential 87B : Busbar differential 87L : Line differential (46 : Negative sequence / unbalance) (37 : Phase undercurrent)
Schneider Electric - Division - Name Date

Current & Voltage analog Inputs are needed

The way for the polarity of CT is important

Usual ANSI codes for Voltage protection

27 : Undervoltage (27D : Positive sequence undervoltage) 27R : Remanente undervoltage 59 : Overvoltage 59N : Neutral voltage displacement (47 : Negative sequence overvoltage) Usefull to be sure that no voltage on busbar even if some motor are not stop Solution to detect the first fault on IT earthing system

Normally = not latched

25 : Synchro-check
- 25 = Module MCS025 for SEPAM (only on SEPAM 60 or 80) - Voltage Reference = 1 single Voltage or 1 composed voltage - VT healthy circuit is needed (to be sure when the busbar is dead
MCB 25 VT VT MCB

Source 1

Source 2

VT are healthy (=1) if fuses are drawn-in

and fuses are not blown and MCB is closed

Fuse

Fuse

Fuses are drawn-in

Fuses are not blown

MCB close

Schneider Electric - Division - Name Date

Usual ANSI codes for transformer or motor protection

26 / 63 : Thermostat / buchholz (DMCR or DGPT2)

Transformer protection
38 / 49T : Temperature monitoring
8 sensors (PT100 or Ni100) per module (MET-148) for SEPAM

48/51LR : Excessive starting time / Loked rotor 66 : Starts per hour

Motor protection

Schneider Electric - Division - Name Date

ANSI codes for frequency & Power protection

(81H : Overfrequency) (81L : Underfrequency) (81R : Rate of change of frequency)

32P : Directional active overpower (32Q : Directional reactive overpower) (37P : Directional active underpower) Others ansi codes : - 64G (100% stator) 79 (recloser) 24 (overfluxing) 67NC (for compensed neutral)

Schneider Electric - Division - Name Date

SEPAM Range
SEPAM series 100

SEPAM series 10

SEPAM series 20, 40, 60 & 80

Schneider Electric - Division - Name Date

SEPAM series 100

SEPAM 100 RT =
For transformer protection applications : DGPT2 or Buchholz + thermostat information.

SEPAM 100 LA =
For back-up protection : Phase overcurrent (50/51) & earth fault (50N/51N) :

SEPAM 100 LD =
High impedance differential relay. It provides restricted earth fault, busbar and machine protection.

SEPAM 100 MI =
High impedance differential relay. It provides restricted earth fault, busbar and machine protection.

Schneider Electric - Division - Name Date

SEPAM series 10

Schneider Electric - Division - Name Date

SEPAM series 20, 40, 60 & 80

Schneider Electric - Division - Name Date

SEPAM series 20 & 40 (selection table 1/2)

Schneider Electric - Division - Name Date

10

SEPAM series 20 & 40 (selection table 2/2)

Schneider Electric - Division - Name Date

11

SEPAM series 60 (selection table 1/3)

Schneider Electric - Division - Name Date

12

SEPAM series 60 (selection table 2/3)

Schneider Electric - Division - Name Date

13

SEPAM series 60 (selection table 3/3)

Schneider Electric - Division - Name Date

14

SEPAM series 80 (selection table 1/3)

Schneider Electric - Division - Name Date

15

SEPAM series 80 (selection table 2/3)

Schneider Electric - Division - Name Date

16

SEPAM series 80 (selection table 3/3)

Schneider Electric - Division - Name Date

17

Different SEPAM UMIs

Basic UMI Remote advanced UMI Integrated advanced UMI Mimic-based UMI

Series 20 & 40

Series 80 & 60

Schneider Electric - Division - Name Date

18

Optional modules Sepam series 20 & 40

MES114 optional input/output modules ACE949-2 ACE959 ACE937 ACE969TP ACE969FO communication modules

MSA141 analog output module

MES148-2 temperature sensor modules

DSM303 remote UMI

Schneider Electric - Division - Name Date

19

Optional modules Sepam series 60 & 80

MES120 optional input/output modules ACE949-2 ACE959 ACE937 ACE969TP ACE969FO communication modules

MSA141 analog output module

MCS025 synchro-check module

DSM303 remote UMI MES148-2 temperature sensor modules

Schneider Electric - Division - Name Date

20

I/O modules
FOR SEPAM Series 20 & 40 : MES114, MES114E, MES114F 10 inputs / 4 output modules 1 module by SEPAM

FOR SEPAM Series 60 & 80 : MES120, MES120G, MES120H 14 inputs / 6 outputs modules Up to 3 modules for SEPAM 80 Up to 2 modules for SEPAM 60

Schneider Electric - Division - Name Date

21

Communication module possibilities

ACE949-2 : 2-wire RS 485 network interface ACE959 : 4-wire RS 485 network interface ACE937 Fiber optic interface ACE969TP-2 Network interfaces ACE969FO-2 Network interfaces ACE850TP Network interfaces ACE850FO Network interfaces
Schneider Electric - Division - Name Date 22

Modbus RTU Modbus TCP/IP IEC 60870-5-103 DNP3 IEC 61850

Residual current inputs : CSH 30/120/200

of gh d n le it e ll fu lim re s ar g i c e irin B w

CSH120 or CSH200 core balance CT r ratio of 1/470 fo ion d te llat p a da nst a i ot o r N o d ut o

CT + CSH30
connection of CT with secondary 1A: 2 turns 5A: 4 turns Or direct on CCA634

Schneider Electric - Division - Name Date

23

Current sensor inputs

Series 20 Series 40 Series 80

CCA630/CCA634 connector The CCA630 connector is used to connect 3 phase current transformers to Sepam The CCA634 adds an input for a residual current transformer : do not connect a core balance ct With CCA634 Io input on A or E connector must not be used. Both contain interposing ring CTs with through primaries and be disconnected with the power on since disconnection does not open the CT secondary circuit.
24

CT 1 or 5A

Schneider Electric - Division - Name Date

Characteristics comparison
Series 20 Power supply User / Machine Interface Basic I/O Maximum I/O Sensors 24 / 250 V DC 110 / 240 V AC No UMI or remote advanced UMI 0 inputs / 4 outputs 10 inputs / 8 outputs 3 CTs + 1 core balance CT Or 4 VTs 1 3 CTs + 3 VTs + 1 core balance CT 1 Yes Series 40 Series 80 24 / 250 V DC No UMI Or advanced UMI Or mimic-based UMI 0 inputs / 5 outputs 42 inputs / 23 outputs 3 CTs + 4 VTs + 2 core bal. CTs 6 CTs + 4 VTs + 2 core bal. CTs Or 3 CTs + 8 VTs + 1 cor. bal. CT 2 Yes Yes (optional) Yes Yes

Communication port Equation editor Logipam Removable cartridge Battery

Schneider Electric - Division - Name Date

25

SEPAM series 20 : Ordered form (1/2)

Schneider Electric - Division - Name Date

26

SEPAM series 20 : Ordered form (2/2)

Schneider Electric - Division - Name Date

27

SEPAM series 40 : Ordered form (1/2)

Schneider Electric - Division - Name Date

28

SEPAM series 40 : Ordered form (2/2)

Schneider Electric - Division - Name Date

29

SEPAM series 60 : Ordered form (1/2)

Schneider Electric - Division - Name Date

30

SEPAM series 60 : Ordered form (2/2)

Schneider Electric - Division - Name Date

31

SEPAM series 80 : Ordered form (1/2)

Schneider Electric - Division - Name Date

32

SEPAM series 80 : Ordered form (2/2)

Schneider Electric - Division - Name Date

33

Main points to remember

Take care of storage conditions Connecting Sepam and additional modules to earth is compulsory. All output relays are not identical :
Some are control type with 8A continuous current For Sepam 20/40 : O1 / 02 / 011 For Sepam 60/80 :O1 -> 04 et O101 / O201 / O301

The availability of some protection functions depend on VTs wiring ACExxx communication modules need to be powered with 12 or 24 V DC Synchro check option only work with series 60 or 80 and need specific cable CCA 785

Schneider Electric - Division - Name Date

34