LabVIEW Basics I: Introduction Course Manual

Course Software Version 8.5 September 2007 Edition Part Number 320628R-01 LabVIEW Introduction Course Manual
Copyright 19932007 National Instruments Corporation. All rights reserved. Under the copyright laws, this publication may not be reproduced or transmitted in any form, electronic or mechanical, including photocopying, recording, storing in an information retrieval system, or translating, in whole or in part, without the prior written consent of National Instruments Corporation. National Instruments respects the intellectual property of others, and we ask our users to do the same. NI software is protected by copyright and other intellectual property laws. Where NI software may be used to reproduce software or other materials belonging to others, you may use NI software only to reproduce materials that you may reproduce in accordance with the terms of any applicable license or other legal restriction. The following notices relate to certain components used in USI (Xerces C++, ICU, HDF5, Citadel 5, b64 library, and Stingray). For a listing of the conditions and disclaimers regarding these components, refer to the USICopyrights.chm. Xerces C++. This product includes software developed by the Apache Software Foundation (http://www.apache.org/). Copyright 1999 The Apache Software Foundation. All rights reserved. ICU. Copyright 19952003 International Business Machines Corporation and others. All rights reserved. HDF5. NCSA HDF5 (Hierarchical Data Format 5) Software Library and Utilities Copyright 1998, 1999, 2000, 2001, 2003 by the Board of Trustees of the University of Illinois. All rights reserved. Citadel 5. In regards to components that use Citadel 5, the following copyright applies. Copyright 1994 Hewlett-Packard Company. b64 library. Copyright 20042006, Matthew Wilson and Synesis Software. All Rights Reserved. Stingray. This software includes Stingray software developed by the Rogue Wave Software division of Quovadx, Inc. Copyright 19952006, Quovadx, Inc. All Rights Reserved. Trademarks National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. FireWire is the registered trademark of Apple Computer, Inc. Other product and company names mentioned herein are trademarks or trade names of their respective companies. Members of the National Instruments Alliance Partner Program are business entities independent from National Instruments and have no agency, partnership, or joint-venture relationship with National Instruments. Patents For patents covering National Instruments products, refer to the appropriate location: HelpPatents in your software, the patents.txt file on your CD, or ni.com/legal/patents.

TM

Worldwide Technical Support and Product Information ni.com National Instruments Corporate Headquarters 11500 North Mopac Expressway Austin, Texas 78759-3504 USA Tel: 512 683 0100 Worldwide Offices Australia 1800 300 800, Austria 43 662 457990-0, Belgium 32 (0) 2 757 0020, Brazil 55 11 3262 3599, Canada 800 433 3488, China 86 21 5050 9800, Czech Republic 420 224 235 774, Denmark 45 45 76 26 00, Finland 358 (0) 9 725 72511, France 01 57 66 24 24, Germany 49 89 7413130, India 91 80 41190000, Israel 972 3 6393737, Italy 39 02 41309277, Japan 0120-527196, Korea 82 02 3451 3400, Lebanon 961 (0) 1 33 28 28, Malaysia 1800 887710, Mexico 01 800 010 0793, Netherlands 31 (0) 348 433 466, New Zealand 0800 553 322, Norway 47 (0) 66 90 76 60, Poland 48 22 3390150, Portugal 351 210 311 210, Russia 7 495 783 6851, Singapore 1800 226 5886, Slovenia 386 3 425 42 00, South Africa 27 0 11 805 8197, Spain 34 91 640 0085, Sweden 46 (0) 8 587 895 00, Switzerland 41 56 2005151, Taiwan 886 02 2377 2222, Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545 For further support information, refer to the Additional Information and Resources appendix. To comment on National Instruments documentation, refer to the National Instruments Web site at ni.com/info and enter the info code feedback.

Contents
Student Guide
A. B. C. D. E. About This Manual ...............................................................................................viii What You Need to Get Started .............................................................................ix Installing the Course Software..............................................................................ix Course Goals.........................................................................................................x Course Conventions ..............................................................................................x

Lesson 1 Problem Solving

A. Software Development Method ............................................................................1-2 B. Scenario ................................................................................................................1-2 C. Design ...................................................................................................................1-3 D. Implementation .....................................................................................................1-6 E. Testing ..................................................................................................................1-7 F. Maintenance..........................................................................................................1-7 Exercise 1-1 Software Development Method........................................................1-8 G. Course Project.......................................................................................................1-10

Lesson 2 Navigating LabVIEW

A. Virtual Instruments (VIs)......................................................................................2-2 B. Parts of a VI ..........................................................................................................2-2 C. Starting a VI..........................................................................................................2-4 D. Project Explorer ....................................................................................................2-9 E. Front Panel Window .............................................................................................2-14 F. Block Diagram Window .......................................................................................2-20 Exercise 2-1 Concept: Exploring a VI...................................................................2-29 G. Searching for Controls, VIs, and Functions..........................................................2-30 Exercise 2-2 Concept: Navigating Palettes ...........................................................2-32 H. Selecting a Tool ....................................................................................................2-33 Exercise 2-3 Concept: Selecting a Tool ................................................................2-40 I. Data Flow..............................................................................................................2-44 Exercise 2-4 Concept: Data Flow..........................................................................2-46 J. Creating a Simple VI ............................................................................................2-47 Exercise 2-5 Simple AAP VI.................................................................................2-51

Lesson 3 Troubleshooting and Debugging VIs

A. LabVIEW Help Utilities .......................................................................................3-2 Exercise 3-1 Concept: Using Help ........................................................................3-5 B. Correcting Broken VIs..........................................................................................3-9 C. Debugging Techniques .........................................................................................3-11

National Instruments Corporation

iii

LabVIEW Introduction Course Manual

Contents

D. Undefined or Unexpected Data.............................................................................3-17 E. Error Checking and Error Handling......................................................................3-18 Exercise 3-2 Concept: Debugging.........................................................................3-21

Lesson 4 Implementing a VI
A. Designing Front Panel Windows ..........................................................................4-2 B. LabVIEW Data Types ..........................................................................................4-9 C. Documenting Code ...............................................................................................4-16 Exercise 4-1 Determine Warnings VI ...................................................................4-19 D. While Loops..........................................................................................................4-26 Exercise 4-2 Auto Match VI..................................................................................4-30 E. For Loops ..............................................................................................................4-37 Exercise 4-3 Concept: While Loops versus For Loops .........................................4-41 F. Timing a VI...........................................................................................................4-44 G. Iterative Data Transfer ..........................................................................................4-45 Exercise 4-4 Average Temperature VI..................................................................4-48 H. Plotting Data .........................................................................................................4-52 Exercise 4-5 Temperature Multiplot VI ................................................................4-58 I. Case Structures .....................................................................................................4-63 Exercise 4-6 Determine Warnings VI ...................................................................4-69 J. Formula Nodes......................................................................................................4-74 Exercise 4-7 Self-Study: Square Root VI..............................................................4-76 Exercise 4-8 Self-Study: Determine Warnings VI (Challenge) ............................4-80 Exercise 4-9 Self-Study: Determine More Warnings VI.......................................4-83

Lesson 5 Relating Data

A. Arrays....................................................................................................................5-2 Exercise 5-1 Concept: Manipulating Arrays .........................................................5-7 B. Clusters .................................................................................................................5-14 Exercise 5-2 Concept: Clusters..............................................................................5-20 C. Type Definitions ...................................................................................................5-26 Exercise 5-3 Type Definition ................................................................................5-30

Lesson 6 Storing Measurement Data

A. Understanding File I/O .........................................................................................6-2 B. Understanding High-Level File I/O ......................................................................6-4 Exercise 6-1 Spreadsheet Example VI ..................................................................6-5 C. Understanding Low-Level File I/O.......................................................................6-8 Exercise 6-2 Temperature Log VI .........................................................................6-10 Exercise 6-3 Self-Study: Read VCard VI..............................................................6-13

LabVIEW Introduction Course Manual

iv

ni.com

Contents

Lesson 7 Developing Modular Applications

A. Understanding Modularity ....................................................................................7-2 B. Building the Icon and Connector Pane .................................................................7-3 C. Using SubVIs ........................................................................................................7-9 Exercise 7-1 Determine Warnings VI ...................................................................7-11

Lesson 8 Acquiring Data

A. Using Hardware ....................................................................................................8-2 B. Communicating with Hardware............................................................................8-5 C. Simulating a DAQ Device ....................................................................................8-10 Exercise 8-1 Concept: MAX ................................................................................8-11 D. Measuring Analog Input .......................................................................................8-17 Exercise 8-2 Triggered Analog Input VI...............................................................8-19 E. Generating Analog Output....................................................................................8-24 F. Using Counters .....................................................................................................8-26 Exercise 8-3 Count Events VI ...............................................................................8-27 G. Using Digital I/O ..................................................................................................8-30 Exercise 8-4 Optional: Digital Count VI...............................................................8-31

Lesson 9 Instrument Control

A. Using Instrument Control .....................................................................................9-2 B. Using GPIB...........................................................................................................9-2 C. Using Serial Port Communication ........................................................................9-3 D. Using Other Interfaces ..........................................................................................9-6 E. Software Architecture ...........................................................................................9-7 Exercise 9-1 Concept: GPIB Configuration with MAX........................................9-9 F. Using the Instrument I/O Assistant.......................................................................9-14 Exercise 9-2 Concept: Instrument I/O Assistant ...................................................9-16 G. Using VISA...........................................................................................................9-31 Exercise 9-3 VISA Write and Read VI .................................................................9-34 H. Using Instrument Drivers......................................................................................9-38 Exercise 9-4 Concept: NI Devsim VI....................................................................9-41

Lesson 10 Common Design Techniques and Patterns

A. Using Sequential Programming ............................................................................10-2 B. Using State Programming .....................................................................................10-5 C. State Machines ......................................................................................................10-5 Exercise 10-1 State Machine VI..............................................................................10-14 D. Using Parallelism ..................................................................................................10-21

National Instruments Corporation

LabVIEW Introduction Course Manual

Contents

Appendix A Analyzing and Processing Numeric Data

A. Choosing the Correct Method for Analysis ..........................................................A-2 B. Analysis Categories ..............................................................................................A-4 Exercise A-1 Concept: Analysis Types..................................................................A-6

Appendix B Measurement Fundamentals

A. Using Computer-Based Measurement Systems....................................................B-2 B. Understanding Measurement Concepts ................................................................B-3 C. Increasing Measurement Quality ..........................................................................B-12 Exercise B-1 Concepts: Measurement Fundamentals............................................B-18

Appendix C CAN: Controller Area Network

A. History of CAN.....................................................................................................C-2 B. CAN Basics...........................................................................................................C-4 Exercise C-0 Concept: CAN Device Setup............................................................C-7 C. Channel Configuration..........................................................................................C-9 Exercise C-1 Channel Configuration .....................................................................C-12 D. CAN APIs .............................................................................................................C-17 E. CAN Programming in LabVIEW (Channel API).................................................C-18 Exercise C-2 Read and Write CAN Channels........................................................C-21 Exercise C-3 Synchronize CAN & DAQ...............................................................C-26

Appendix D Additional Information and Resources Index Course Evaluation

LabVIEW Introduction Course Manual

vi

ni.com

Student Guide
Thank you for purchasing the LabVIEW Basics I: Introduction course kit. You can begin developing an application soon after you complete the exercises in this manual. This course manual and the accompanying software are used in the three-day, hands-on LabVIEW Basics I: Introduction course. You can apply the full purchase of this course kit toward the corresponding course registration fee if you register within 90 days of purchasing the kit. Visit ni.com/training for online course schedules, syllabi, training centers, and class registration. For course manual updates and corrections, refer to ni.com/info and enter the info code rdlvce.
Note

The LabVIEW Basics I: Introduction course is part of a series of courses designed to build your proficiency with LabVIEW and help you prepare for NI LabVIEW certification exams. The following illustration shows the courses that are part of the LabVIEW training series. Refer to ni.com/training for more information about NI Certification.
Courses New User Begin Here LabVIEW Basics I* LabVIEW Basics II* Skills learned: LabVIEW environment navigation Basic application creation using LabVIEW Experienced User LabVIEW Intermediate I* LabVIEW Intermediate II* Skills learned: Modular application development Structured design and development practices Memory management and VI performance improvement Advanced User LabVIEW Advanced Application Development Skills learned: Large application design Code reuse maximization Object-oriented programming in LabVIEW

Certifications Certified LabVIEW Associate Developer Exam Skills tested: LabVIEW environment knowledge Certified LabVIEW Developer Exam Skills tested: LabVIEW application development expertise Certified LabVIEW Architect Exam Skills tested: LabVIEW application development mastery

Hardware-Based Courses: Data Acquisition and Signal Conditioning Modular Instruments Instrument Control Machine Vision Motion Control LabVIEW Real-Time Compact RIO
*Core courses are strongly recommended to realize maximum productivity gains when using LabVIEW.

National Instruments Corporation

vii

LabVIEW Introduction Course Manual

Student Guide

A. About This Manual

Use this manual to learn about LabVIEW programming concepts, techniques, features, VIs, and functions you can use to create test and measurement, data acquisition, instrument control, datalogging, measurement analysis, and report generation applications. This course manual assumes that you are familiar with Windows and that you have experience writing algorithms in the form of flowcharts or block diagrams. The course manual is divided into lessons, each covering a topic or a set of topics. Each lesson consists of the following: An introduction that describes the purpose of the lesson and what you will learn A description of the topics in the lesson A set of exercises to reinforce those topics Some lessons include optional and challenge exercise sections or a set of additional exercises to complete if time permits. A summary that outlines important concepts and skills taught in the lesson

Several exercises in this manual use one of the following National Instruments hardware products: A plug-in multifunction data acquisition (DAQ) device connected to a DAQ Signal Accessory containing a temperature sensor, function generator, and LEDs A GPIB interface connected to an NI Instrument Simulator

If you do not have this hardware, you still can complete the exercises. Alternate instructions are provided for completing the exercises without hardware. Exercises that explicitly require hardware are indicated with an icon, shown at left. You also can substitute other hardware for those previously mentioned. For example, you can use a GPIB instrument in place of the NI Instrument Simulator, or another National Instruments DAQ device connected to a signal source, such as a function generator.

LabVIEW Introduction Course Manual

viii

ni.com

Student Guide

B. What You Need to Get Started

Before you use this course manual, ensure you have all the following items: Windows 2000 or later installed on your computer. The course is optimized for Windows XP. Multifunction DAQ device configured as device 1 using Measurement & Automation Explorer (MAX) DAQ Signal Accessory, wires, and cable GPIB interface NI Instrument Simulator and power supply LabVIEW Full or Professional Development System 8.5 or later A serial cable A GPIB cable LabVIEW Basics I: Introduction course CD, which installs the following folders: Folder name
Exercises

Description Folder for saving VIs created during the course and for completing certain course exercises; also includes subVIs necessary for some exercises and zip file (nidevsim.zip) containing the LabVIEW instrument driver for the NI Instrument Simulator Folder containing the solutions to all the course exercises

Solutions

C. Installing the Course Software

Complete the following steps to install the course software. 1. Insert the course CD in your computer. The LabVIEW Basics Course Material Setup dialog box displays. 2. Click the Next button. 3. Choose Typical in the setup type and click the Install button to begin the installation. 4. Click the Finish button to exit the Setup Wizard. The installer places the Exercises and Solutions folders at the top level of the C: directory.

National Instruments Corporation

ix

LabVIEW Introduction Course Manual

Student Guide

D. Course Goals
This course prepares you to do the following: Understand front panels, block diagrams, icons, and connector panes Use the programming structures and data types that exist in LabVIEW Use various editing and debugging techniques Create and save VIs so you can use them as subVIs Display and log data Create applications that use plug-in DAQ devices Create applications that use serial port and GPIB instruments

This course does not describe the following: Every built-in VI, function, or object; refer to the LabVIEW Help for more information about LabVIEW features not described in this course Analog-to-digital (A/D) theory Operation of the serial port Operation of the GPIB bus Developing an instrument driver Developing a complete application for any student in the class; refer to the NI Example Finder, available by selecting HelpFind Examples, for example VIs you can use and incorporate into VIs you create

E. Course Conventions
The following conventions appear in this course manual: The symbol leads you through nested menu items and dialog box options to a final action. The sequence FilePage SetupOptions directs you to pull down the File menu, select the Page Setup item, and select Options from the last dialog box. This icon denotes a tip, which alerts you to advisory information. This icon denotes a note, which alerts you to important information. This icon denotes a caution, which advises you of precautions to take to avoid injury, data loss, or a system crash. This icon indicates that an exercise requires a plug-in GPIB interface or DAQ device.

LabVIEW Introduction Course Manual

ni.com

Student Guide

bold

Bold text denotes items that you must select or click in the software, such as menu items and dialog box options. Bold text also denotes parameter names, controls and buttons on the front panel, dialog boxes, sections of dialog boxes, menu names, and palette names. Italic text denotes variables, emphasis, a cross-reference, or an introduction to a key concept. Italic text also denotes text that is a placeholder for a word or value that you must supply. Text in this font denotes text or characters that you enter from the keyboard, sections of code, programming examples, and syntax examples. This font also is used for the proper names of disk drives, paths, directories, programs, subprograms, subroutines, device names, functions, operations, variables, filenames, and extensions. Text in this font denotes the messages and responses that the computer automatically prints to the screen. This font also emphasizes lines of code that are different from the other examples. Text in this font denotes a specific platform and indicates that the text following it applies only to that platform.

italic

monospace

monospace bold

Platform

National Instruments Corporation

xi

LabVIEW Introduction Course Manual

Problem Solving

LabVIEW is a programming language you can use to solve various problems. Problem-solving skills are essential to creating solutions in LabVIEW. Computer programmers use a software development method to solve problems using software programs. Following a method helps a programmer to develop code that has greater potential to successfully solve a given problem as compared to writing code without a plan. A method also helps to make code more readable, scalable, and modifiable. You will use the strategy described in this lesson to solve problems throughout the course.

Topics
A. Software Development Method B. Scenario C. Design D. Implementation E. Testing F. Maintenance G. Course Project

National Instruments Corporation

1-1

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

A. Software Development Method

Following a set of steps that has been refined over the years by software engineers can simplify solving problems using software. This course describes a specific set of steps called the software development method. The software development method is a strategy for using LabVIEW to implement a software solution. Use the software development method to create a solution to your problem. In the software development method, complete the following steps: 1. Define the problem (scenario). 2. Design an algorithm and/or flowchart. 3. Implement the design. 4. Test and verify the implementation. 5. Maintain and update the implementation. During this course, this software development method serves as a framework for all hands-on development exercises. In most exercises, you receive the scenario and design steps. Then you complete the implementation, testing, and maintenance steps. During this course, you learn to create successful implementations. Furnace ExampleA furnace example in this lesson illustrates each step of the software development method described.

B. Scenario
During the scenario stage of the software development method, you define what your problem is so that you can approach it with all the necessary factors identified. You can remove extraneous factors during this phase and focus on the core problem that you must solve. How you identify the problem initially can save you time while you design and implement a solution. Furnace ExampleAssume that you must cure a material at a certain temperature for a set amount of time in a furnace. For this problem, it is not necessary to know the material type or the time of day. You must know the cure time, cure temperature, and method for adjusting the furnace temperature.

LabVIEW Introduction Course Manual

1-2

ni.com

Lesson 1

Problem Solving

C. Design
After you determine the scope of the problem, you can design a solution by analyzing the problem. Part of analyzing the problem is identifying the inputs and outputs of the software, as well as any additional requirements. After you define the inputs and outputs, you can design an algorithm, flowchart and/or state transition diagram to help you arrive at a software solution.

Identify the Inputs

The inputs indicate the raw data that you want to process during the problem solving process. Furnace ExampleInputs for the furnace software are the cure time (seconds), the necessary cure temperature (Kelvin), and the furnace temperature (Kelvin).

Identify the Outputs

The outputs represent the result of the calculation, processing, or other condition that the problem solving process implements. Furnace ExampleThe output of the furnace software is an on/off switch that applies voltage to the furnace coil. Voltage is applied to the coil by changing the state of a switch that controls the voltage supply to the coils. When the voltage is applied or removed, the furnace has an immediate change in temperature.

Identify Additional Requirements

Consider any other factors that might influence solving the problem. For example, do you need to use specific units such as centimeters or seconds? Furnace ExampleAs an additional requirement for this example, assume that the furnace cannot start until the interior temperature is the same as the exterior temperature.

Designing an Algorithm to Solve the Problem

After determining the inputs, outputs, and additional requirements, you can create an algorithm. An algorithm is a set of steps that process your inputs and create outputs. Furnace ExampleThis algorithm describes the operation of the furnace: 1. Read exterior temperature. 2. Read interior temperature. 3. If interior temperature is not equal to exterior temperature, go to step 1.

National Instruments Corporation

1-3

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

4. Read interior temperature. 5. If interior temperature is greater than or equal to desired temperature, turn off voltage to coil. 6. If current temperature is less than desired temperature, turn on voltage to coil. 7. If time is less than cure time, go to step 4. 8. Turn off voltage to coil.

Designing a Flowchart
A flowchart displays the steps for solving the problem. Flowcharts are useful because you can follow more complex processes of an algorithm in a visual way. For example, you can see if a specific step has two different paths to the end solution and you can plan your code accordingly. Furnace ExampleYou can design this example using either an algorithm or a flowchart. Figure 1-1 shows a flowchart following the algorithm designed in the previous subsection.

Start Legend T = Current Temperature X = Desired Temperature Y = Exterior Temperature A = Current Time B = Cure Time

No Read T T = Y? Yes Read T

No

Yes Turn Off Voltage T < X? Yes Turn On Voltage A < B? No Stop Yes No

Figure 1-1. Flowchart for Furnace Example

LabVIEW Introduction Course Manual

1-4

ni.com

Lesson 1

Problem Solving

Designing a State Transition Diagram

State transition diagrams are a specific type of flowchart that are commonly used when creating LabVIEW state machines. State transition diagrams allow you to clearly indicate the states of a program and what causes the program to transition from one state to the next. A state transition diagram uses a labeled circle to signify a steady state and a labeled arrow to indicate a transition from a state. A state is a part of a program that satisfies a condition, performs an action, or waits for an event. A transition is the condition, action, or event that causes the program to move to the next state. The start of the program is signified with a solid circle, shown at left. The end of the program is signified with a targeted circle, shown at left. Furnace ExampleYou also can use a state transition diagram for this example. Figure 1-2 shows the furnace example redesigned as a state transition diagram. Both the flowchart and the state transition diagram are valid ways to design LabVIEW code, but each may lead to a different programming solution.

National Instruments Corporation

1-5

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

T=Y Compare Temperatures

Legend T = Current Temperature X = Desired Temperature Y = Exterior Temperature A = Current Time B = Cure Time

A<B T=Y

T<X

Turn On Voltage

Acquire Oven Temperature T >= X Check Time A >= B

Turn Off Voltage

Figure 1-2. State Transition Diagram for Furnace Example

D. Implementation
In the implementation stage, you create code for your algorithm or flowchart. When writing code in a text-based language, the algorithm elegantly translates into each line of code, depending on the level of detail shown in the algorithm. Because LabVIEW is a graphical programming language, the flowchart works much the same way. Refer to Lesson 10, Common Design Techniques and Patterns, for more information about implementing LabVIEW VIs from a flowchart or state transition diagram.

LabVIEW Introduction Course Manual

1-6

ni.com

Lesson 1

Problem Solving

E. Testing
Testing and verifying is an important part of the software development method. Make sure to test your implementation with data that is both logical and illogical for the solution you created. Testing logical data verifies that the inputs produce the expected result. By testing illogical data, you can test to see if the code has effective error handling. Furnace ExampleTo test the error handling strategy of the furnace example, you could input a cure temperature that is less than the ambient temperature. An effective error handling strategy could alert the user that the furnace can only increase temperature, not decrease it.

F. Maintenance
Maintenance is the ongoing process of resolving programming errors and adding parallel construction changes to the original solution for a problem. Furnace ExampleAfter writing this code, you may discover that the customer wants to add a temperature sensor to another area of the oven to add redundancy to the system. Adding features to the program is easier if you plan for scalability in your software from the beginning.

National Instruments Corporation

1-7

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

Exercise 1-1
Goal

Software Development Method

Solve a problem using the software development method without using software.

Scenario
You are responsible for displaying the time until arrival for airplanes at an airport. You receive this information in seconds, but must display it as a combination of hours/minutes/seconds.

Design
What inputs are you given?

What outputs are you expected to produce?

What is the relationship/conversion between the inputs and outputs?

Tip

Use the Windows calculator to help you determine the relationship. Create an algorithm or flowchart that demonstrates the relationship between the inputs and outputs.

LabVIEW Introduction Course Manual

1-8

ni.com

Lesson 1

Problem Solving

Implementation
During this stage, you implement the program from the algorithm or flowchart. For this exercise, skip this stage. Refer to Exercise 2-1 to see an implementation of a solution to this problem.

Testing
Use a set of known values to test the algorithm or flowchart you designed. Example inputs with corresponding outputs: Input 0 seconds 60 seconds 3600 seconds 3665 seconds Output 0 hours, 0 minutes, 0 seconds 0 hours, 1 minute, 0 seconds 1 hour, 0 minutes, 0 seconds 1 hour, 1 minute, 5 seconds

Maintenance
If a test value set has failed, return to the design phase and check for errors.

End of Exercise 1-1

National Instruments Corporation

1-9

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

G. Course Project
Throughout this course, the course project illustrates concepts, both as hands-on exercises and as a case study. The project meets the following requirements: 1. Acquires a temperature every half a second 2. Analyzes each temperature to determine if the temperature is too high or too low 3. Alerts the user if there is a danger of heat stroke or freeze 4. Displays the data to the user 5. Logs the data if a warning occurs 6. If the user does not stop the program, the entire process repeats The course project has the following inputs and outputs.

Inputs
Current Temperature (T) High Temperature Limit (X) Low Temperature Limit (Y) Stop

Outputs
Warning Levels: Heatstroke Warning, No Warning, Freeze Warning Current Temperature Display Data Log File

One state transition diagram, shown in Figure 1-3, is chosen so that all students may follow the same instruction set. This state transition diagram is chosen because it successfully solves the problem and it has parts that can be effectively used to demonstrate course concepts. However, it may not be the best solution to the problem.

LabVIEW Introduction Course Manual

1-10

ni.com

Lesson 1

Problem Solving

Initialize

Acquistion

Time Elapsed = TRUE and Stop = FALSE

Analysis

Warning = TRUE Datalog

Time Elapsed = FALSE and Stop = FALSE Time Check Warning = FALSE

Stop = TRUE

Figure 1-3. Project State Transition Diagram

Figure 1-4 shows an example of an alternate state transition diagram. This state transition diagram also solves the problem very effectively. One of the major differences between these two diagrams is how they can be expanded for future functionality. In the state transition diagram in Figure 1-3, you can modify the diagram to include warning states for other physical phenomena, such as wind, pressure, and humidity. In the state transition diagram in Figure 1-4, you can add other layers of temperature warnings. The possible future changes you expect to your program affect which diagram you choose.

National Instruments Corporation

1-11

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

Initialize

Time Elapsed = TRUE

Acquisition Time Check T>X? T<Y? Y<T<X? Time Elapsed = FALSE

Heatstroke Warning

Freeze Warning

No Warning

Stop = FALSE

Stop

Stop = TRUE

Figure 1-4. Project State Transition Diagram Alternate

LabVIEW Introduction Course Manual

1-12

ni.com

Lesson 1

Problem Solving

Self-Review: Quiz
Match each step of the described software development method to the correct description of the step. 1. Scenario 2. Design 3. Implementation 4. Testing 5. Maintenance A. Apply an algorithm or flowchart B. Verify the code C. Define the problem D. Update the code E. Identify the inputs and outputs

National Instruments Corporation

1-13

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

Self-Review: Quiz Answers

Match each step of the described software development method to the correct description of the step. 1 2 3 4 5 C. Scenario: Define the problem E. Design: Identify the inputs and outputs A. Implementation: Apply an algorithm or flowchart B. Testing: Verify the code D. Maintenance: Update the code

National Instruments Corporation

1-15

LabVIEW Introduction Course Manual

Lesson 1

Problem Solving

Notes

LabVIEW Introduction Course Manual

1-16

ni.com

Navigating LabVIEW

This lesson introduces how to navigate the LabVIEW environment. This includes using the menus, toolbars, palettes, tools, help, and common dialog boxes of LabVIEW. You also learn how to run a VI and gain a general understanding of a front panel and block diagram. At the end of this lesson, you create a simple VI that acquires, analyzes, and presents data.

Topics
A. Virtual Instruments (VIs) B. Parts of a VI C. Starting a VI D. Project Explorer E. Front Panel Window F. Block Diagram Window G. Searching for Controls, VIs, and Functions H. Selecting a Tool I. Data Flow J. Creating a Simple VI

National Instruments Corporation

2-1

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

A. Virtual Instruments (VIs)

LabVIEW programs are called virtual instruments, or VIs, because their appearance and operation imitate physical instruments, such as oscilloscopes and multimeters. LabVIEW contains a comprehensive set of tools for acquiring, analyzing, displaying, and storing data, as well as tools to help you troubleshoot code you write.

B. Parts of a VI
LabVIEW VIs contain three main componentsthe front panel window, the block diagram, and the icon/connector pane.

Front Panel Window

The front panel window is the user interface for the VI. Figure 2-1 shows an example of a front panel window. You create the front panel window with controls and indicators, which are the interactive input and output terminals of the VI, respectively.

Figure 2-1. VI Front Panel

LabVIEW Introduction Course Manual

2-2

ni.com

Lesson 2

Navigating LabVIEW

Block Diagram Window

After you create the front panel window, you add code using graphical representations of functions to control the front panel objects. Figure 2-2 shows an example of a block diagram window. The block diagram window contains this graphical source code. Front panel objects appear as terminals on the block diagram.

Figure 2-2. Block Diagram

Icon and Connector Pane

You can use a VI as a subVI. A subVI is a VI that is used in another VI, similar to a function in a text-based programming language. To use a VI as a subVI, it must have an icon and a connector pane. Every VI displays an icon in the upper right corner of the front panel window and block diagram window. An example of the default icon is shown at left. An icon is a graphical representation of a VI. The icon can contain both text and images. If you use a VI as a subVI, the icon identifies the subVI on the block diagram of the VI. The default icon contains a number that indicates how many new VIs you opened after launching LabVIEW. To use a VI as a subVI, you need to build a connector pane, shown at left. The connector pane is a set of terminals on the icon that corresponds to the controls and indicators of that VI, similar to the parameter list of a function call in text-based programming languages. Access the connector pane by right-clicking the icon in the upper right corner of the front panel window. You cannot access the connector pane from the icon in the block diagram window.

National Instruments Corporation

2-3

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

C. Starting a VI
When you launch LabVIEW, the Getting Started window appears. Use this window to create new VIs and projects, select among the most recently opened LabVIEW files, find examples, and search the LabVIEW Help. You also can access information and resources to help you learn about LabVIEW, such as specific manuals, help topics, and resources at ni.com/manuals. The Getting Started window closes when you open an existing file or create a new file. You can display the window by selecting ViewGetting Started Window.

Figure 2-3. LabVIEW Getting Started Window

LabVIEW Introduction Course Manual

2-4

ni.com

Lesson 2

Navigating LabVIEW

You can configure LabVIEW to open a new, blank VI on launch instead of displaying the window. Select ToolsOptions, select Environment from the Category list, and place a checkmark in the Skip Getting Started window on launch checkbox.
Note The items in the Getting Started window vary depending on which version of LabVIEW and which toolkits you install.

Creating or Opening a VI or Project

You can begin in LabVIEW by starting from a blank VI or project, opening an existing VI or project and modifying it, or opening a template from which to begin your new VI or project.

Creating New Projects and VIs

To open a new project from the Getting Started window, select Empty Project in the New list. A new, unnamed project opens, and you can add files to and save the project. To open a new, blank VI that is not associated with a project, select Blank VI in the New list in the Getting Started window.

Creating a VI from a Template

Select FileNew to display the New dialog box, which lists the built-in VI templates. You also can display the New dialog box by clicking the New link in the Getting Started window.

National Instruments Corporation

2-5

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Figure 2-4. New Dialog Box

Opening an Existing VI
Select Browse in the Open list in the Getting Started window to navigate to and open an existing VI.
Tip The VIs you edit in this course are located in the <Exercises>\LabVIEW Basics I directory.

LabVIEW Introduction Course Manual

2-6

ni.com

Lesson 2

Navigating LabVIEW

As the VI loads, a status dialog box similar to the following example might appear.

Figure 2-5. Dialog Box Indicating the Status of Loading VIs

The Loading section lists the subVIs of the VI as they load into memory and shows the number of subVIs loaded into memory so far. You can cancel the load at any time by clicking the Stop button. If LabVIEW cannot immediately locate a subVI, it begins searching through all directories specified by the VI search path. You can edit the VI search path by selecting ToolsOptions and selecting Paths from the Category list. You can have LabVIEW ignore a subVI by clicking the Ignore Item button, or you can click the Browse button to search for the missing subVI.

Saving a VI
To save a new VI, select FileSave. If you already saved your VI, select FileSave As to access the Save As dialog box. From the Save As dialog box, you can create a copy of the VI, or delete the original VI and replace it with the new one.

National Instruments Corporation

2-7

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Figure 2-6. Save As Dialog Box Note

Refer to the Save As Dialog Box topic of the LabVIEW Help for detailed information about each option in the Save As dialog box.

LabVIEW Introduction Course Manual

2-8

ni.com

Lesson 2

Navigating LabVIEW

D. Project Explorer
Use projects to group together LabVIEW files and non-LabVIEW files, create build specifications, and deploy or download files to targets. When you save a project, LabVIEW creates a project file (.lvproj), which includes references to files in the project, configuration information, build information, deployment information, and so on. You must use a project to build applications and shared libraries. You also must use a project to work with a real-time (RT), field-programmable gate array (FPGA), or personal digital assistant (PDA) target. Refer to the specific module documentation for more information about using projects with the LabVIEW Real-Time, FPGA, and PDA modules.

Project Explorer Window

Use the Project Explorer window to create and edit LabVIEW projects. Select FileNew Project to display the Project Explorer window. You also can select ProjectNew Project or select Empty Project in the New dialog box to display the Project Explorer window. The Project Explorer window includes two pages, the Items page and the Files page. The Items page displays the project items as they exist in the project tree. The Files page displays the project items that have a corresponding file on disk. You can organize filenames and folders on this page. Project operations on the Files page both reflect and update the contents on disk. You can switch from one page to the other by right-clicking a folder or item under a target and selecting Show in Items View or Show in Files View from the shortcut menu. The Project Explorer window includes the following items by default: Project rootContains all other items in the Project Explorer window. This label on the project root includes the filename for the project. My ComputerRepresents the local computer as a target in the project. DependenciesIncludes items that VIs under a target require. Build SpecificationsIncludes build configurations for source distributions and other types of builds available in LabVIEW toolkits and modules. If you have the LabVIEW Professional Development System or Application Builder installed, you can use Build Specifications to configure stand-alone applications, shared libraries, installers, and zip files.

Tip

A target is any device that can run a VI.

National Instruments Corporation

2-9

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

When you add another target to the project, LabVIEW creates an additional item in the Project Explorer window to represent the target. Each target also includes Dependencies and Build Specifications sections. You can add files under each target.

Project-Related Toolbars
Use the Standard, Project, Build, and Source Control toolbar buttons to perform operations in a LabVIEW project. The toolbars are available at the top of the Project Explorer window, as shown in Figure 2-7. You might need to expand the Project Explorer window to view all of the toolbars.
1 2 3 4

1 2 3

Standard Toolbar Project Toolbar Build Toolbar

4 5 6

Source Control Toolbar Project Root Target

7 8

Dependencies Build Specifications

Figure 2-7. Project Explorer Window Tip

The Source Control toolbar is only available if you have source control configured in LabVIEW. You can show or hide toolbars by selecting ViewToolbars and selecting the toolbars you want to show or hide. You can also right-click an open area on the toolbar and select the toolbars you want to show or hide.

Creating a LabVIEW Project

Complete the following steps to create a project. 1. Select FileNew Project to display the Project Explorer window. You can also select ProjectEmpty Project in the New dialog box to display the Project Explorer window. 2. Add items you want to include in the project under a target. 3. Select FileSave Project to save the project.

LabVIEW Introduction Course Manual

2-10

ni.com

Lesson 2

Navigating LabVIEW

Adding Existing Files To A Project

You can add existing files to a project. Use the My Computer item (or other target) in the Project Explorer window to add files such as VIs or text files, to a LabVIEW project. You can add items to a project in the following ways: Right-click My Computer and select AddFile from the shortcut menu to add a file. You also can select ProjectAdd To ProjectFile from the Project Explorer menu to add a file. Right-click the target and select AddFolder (Auto-populating) from the shortcut menu to add an auto-populating folder. You also can select ProjectAdd To ProjectAdd Folder (Auto-populating) to add an auto-populating folder. LabVIEW continuously monitors and updates the folder according to changes made in the project and on disk. Right-click the target and select AddFolder (Snapshot) from the shortcut menu to add a virtual folder. You also can select ProjectAdd To ProjectAdd Folder (Snapshot) to add a virtual folder. When you select a directory on disk, LabVIEW creates a new virtual folder in the project with the same name as the directory on disk. LabVIEW also creates project items that represent the contents of the entire directory, including files and contents of subdirectories. Selecting a folder on disk adds contents of the entire folder, including files and contents of subfolders.

After you add a virtual folder on disk to a project, LabVIEW does not automatically update the folder in the project if you make changes to the folder on disk.
Note

Right-click the target and select NewVI from the shortcut menu to add a new, blank VI. You also can select FileNew VI or ProjectAdd To ProjectNew VI to add a new, blank VI. Select the VI icon in the upper right corner of a front panel or block diagram window and drag the icon to the target. Select an item or folder from the file system on your computer and drag it to the target.

National Instruments Corporation

2-11

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Removing Items from a Project

You can remove items from the Project Explorer window in the following ways: Right-click the item you want to remove and select Remove from Project from the shortcut menu. Select the item you want to remove and press <Delete>. Select the item you want to remove and click the Remove From Project button on the Standard toolbar.

Note

Removing an item from a project does not delete the item on disk.

Organizing Items in a Project

The Project Explorer window includes two pages, the Items page and the Files page. The Items page displays the project items as they exist in the project tree. The Files page displays the project items that have a corresponding file on disk. You can organize filenames and folders on this page. Project operations on the Files page both reflect and update the contents on disk. You can switch from one page to the other by right-clicking a folder or item under a target and selecting Show in Items View or Show in Files View from the shortcut menu. Use folders to organize items in the Project Explorer window. You can add two types of folders to a LabVIEW project, virtual folders and auto-populating folders. Virtual folders organize project items. Right-click the Project Root or the target and select NewVirtual Folder from the shortcut menu to create a new virtual folder. Auto-populating folders update in real time to reflect the contents of folders on disk. Add an auto-populating folder to the project to view project items as they appear on disk. Auto-populating folders are visible only on the Items page of the Project Explorer window. You can view the disk contents of an auto-populating folder but you cannot perform disk operations such as renaming, reorganizing, and removing project items. To perform disk operations of items in an auto-populating folder, use the Files page of the Project Explorer window. The Files page displays the location of project folders on disk. Project operations on the Files page both update and reflect the contents of the folder on disk. Likewise, LabVIEW automatically updates the auto-populating folder in the project if you make changes to the folder on disk outside of LabVIEW. You can arrange items in a folder. Right-click a folder and select Arrange ByName from the shortcut menu to arrange items in alphabetical order. Right-click a folder and select Arrange ByType from the shortcut menu to arrange items by file type.

LabVIEW Introduction Course Manual

2-12

ni.com

Lesson 2

Navigating LabVIEW

Viewing Files in a Project

When you add a file to a LabVIEW project, LabVIEW includes a reference to the file on disk. Right-click a file in the Project Explorer window and select Open from the shortcut menu to open the file in its default editor. Right-click the project and select ViewFull Paths from the shortcut menu to view where files that a project references are saved on disk. Use the Project File Information dialog box to view where files that a project references are located on disk and in the Project Explorer window. Select ProjectFile Information to display the Project File Information dialog box. You also can right-click the project and select ViewFile Information from the shortcut menu to display the Project File Information dialog box.

Saving a Project
You can save a LabVIEW project in the following ways: Select FileSave Project. Select ProjectSave Project. Right-click the project and select Save from the shortcut menu. Click the Save Project button on the Project toolbar.

You must save new, unsaved files in a project before you can save the project. When you save a project, LabVIEW does not save dependencies as part of the project file.
Note Make a backup copy of a project when you prepare to make major revisions to the project.

National Instruments Corporation

2-13

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

E. Front Panel Window

When you open a new or existing VI, the front panel window of the VI appears. The front panel window is the user interface for the VI. Figure 2-8 shows an example of a front panel window.

1 3 2

Front Panel Window

Toolbar

Controls Palette

Figure 2-8. Example of a Front Panel

Controls and Indicators

You create the front panel window with controls and indicators, which are the interactive input and output terminals of the VI, respectively. Controls are knobs, push buttons, dials, and other input devices. Indicators are graphs, LEDs and other displays. Controls simulate instrument input devices and supply data to the block diagram of the VI. Indicators simulate instrument output devices and display data the block diagram acquires or generates. Figure 2-8 has the following objects: two controls: Number of Measurements and Delay(sec). It has one indicator: an XY graph named Temperature Graph. The user can change the input value for the Number of Measurements and Delay(sec) controls. The user can see the value generated by the VI on the Temperature Graph indicator. The VI generates the values for the

LabVIEW Introduction Course Manual

2-14

ni.com

Lesson 2

Navigating LabVIEW

indicators based on the code created on the block diagram. You learn about the block diagram in the Numeric Controls and Indicators section. Every control or indicator has a data type associated with it. For example, the Delay (sec) horizontal slide is a numeric data type. The most commonly used data types are numeric, Boolean value and string. You learn about other data types in Lesson 3, Troubleshooting and Debugging VIs.

Numeric Controls and Indicators

The numeric data type can represent numbers of various types, such as integer or real. The two common numeric objects are the numeric control and the numeric indicator, as shown in Figure 2-9. Objects such as meters and dials also represent numeric data.

1 2

Increment/Decrement Buttons Numeric Control

Numeric Indicator

Figure 2-9. Numeric Controls and Indicators

To enter or change values in a numeric control, click the increment and decrement buttons with the Operating tool or double-click the number with either the Labeling tool or the Operating tool, enter a new number, and press the <Enter> key.

Boolean Controls and Indicators

The Boolean data type represents data that only has two parts, such as TRUE and FALSE or ON and OFF. Use Boolean controls and indicators to enter and display Boolean values. Boolean objects simulate switches, push buttons, and LEDs. The vertical toggle switch and the round LED Boolean objects are shown in Figure 2-10.

Figure 2-10. Boolean Controls and Indicators

National Instruments Corporation

2-15

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

String Controls and Indicators

The string data type is a sequence of ASCII characters. Use string controls to receive text from the user such as a password or user name. Use string indicators to display text to the user. The most common string objects are tables and text entry boxes as shown in Figure 2-11.

Figure 2-11. String Controls and Indicators

Controls Palette
The Controls palette contains the controls and indicators you use to create the front panel. You access the Controls palette from the front panel window by selecting ViewControls Palette. The Controls palette is broken into various categories; you can expose some or all of these categories to suit your needs. Figure 2-12 shows a Controls palette with all of the categories exposed and the Modern category expanded. During this course, you work exclusively in the Modern category.

Figure 2-12. Controls Palette

LabVIEW Introduction Course Manual

2-16

ni.com

Lesson 2

Navigating LabVIEW

To view or hide categories (subpalettes), select the View button on the palette, and select or deselect in the Always Visible Categories option. You learn more about using the Controls palette in Exercise 2-2.

Shortcut Menus
All LabVIEW objects have associated shortcut menus. As you create a VI, use the shortcut menu items to change the appearance or behavior of front panel and block diagram objects. To access the shortcut menu, right-click the object. Figure 2-13 shows a shortcut menu for a meter.

Figure 2-13. Shortcut Menu for a Meter

Property Dialog Boxes

Objects in the front panel window also have property dialog boxes that you can use to change the look or behavior of the objects. Right-click an object and select Properties from the shortcut menu to access the property dialog box for an object. The Figure 2-14 shows the property dialog box for the meter shown in Figure 2-13. The options available on the property dialog box for an object are similar to the options available on the shortcut menu for that object.

National Instruments Corporation

2-17

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Figure 2-14. Property Dialog Box for a Meter

Front Panel Window Toolbar

Each window has a toolbar associated with it. Use the front panel window toolbar buttons to run and edit the VI. The following toolbar appears on the front panel window.

Click the Run button to run a VI. LabVIEW compiles the VI, if necessary. You can run a VI if the Run button appears as a solid white arrow, shown at left. The solid white arrow also indicates you can use the VI as a subVI if you create a connector pane for the VI. While the VI runs, the Run button appears as shown at left if the VI is a top-level VI, meaning it has no callers and therefore is not a subVI. If the VI that is running is a subVI, the Run button appears as shown at left. The Run button appears broken when the VI you are creating or editing contains errors. If the Run button still appears broken after you finish wiring the block diagram, the VI is broken and cannot run. Click this button to display the Error list window, which lists all errors and warnings.

LabVIEW Introduction Course Manual

2-18

ni.com

Lesson 2

Navigating LabVIEW

Click the Run Continuously button to run the VI until you abort or pause execution. You also can click the button again to disable continuous running. While the VI runs, the Abort Execution button appears. Click this button to stop the VI immediately if there is no other way to stop the VI. If more than one running top-level VI uses the VI, the button is dimmed. The Abort Execution button stops the VI immediately, before the VI finishes the current iteration. Aborting a VI that uses external resources, such as external hardware, might leave the resources in an unknown state by not resetting or releasing them properly. Design VIs with a stop button to avoid this problem.
Caution

Click the Pause button to pause a running VI. When you click the Pause button, LabVIEW highlights on the block diagram the location where you paused execution, and the Pause button appears red. Click the Pause button again to continue running the VI. Select the Text Settings pull-down menu to change the font settings for the selected portions of the VI, including size, style, and color. Select the Align Objects pull-down menu to align objects along axes, including vertical, top edge, left, and so on. Select the Distribute Objects pull-down menu to space objects evenly, including gaps, compression, and so on. Select the Resize Objects pull-down menu to resize multiple front panel objects to the same size. Select the Reorder pull-down menu when you have objects that overlap each other and you want to define which one is in front or back of another. Select one of the objects with the Positioning tool and then select from Move Forward, Move Backward, Move To Front, and Move To Back. Select the Show Context Help Window button to toggle the display of the Context Help window. Enter Text appears to remind you that a new value is available to replace an old value. The Enter Text button disappears when you click it, press the <Enter> key, or click the front panel or block diagram workspace.
Tip The <Enter> key on the numeric keypad ends a text entry, while the main <Enter> key adds a new line. To modify this behavior, select ToolsOptions, select the Environment from the Category list, and place a checkmark in the End text entry with Enter key option.

National Instruments Corporation

2-19

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

F. Block Diagram Window

Block diagram objects include terminals, subVIs, functions, constants, structures, and wires, which transfer data among other block diagram objects.

Indicator Terminals

Wires

Nodes

Control Terminals

Figure 2-15. Example of a Block Diagram and Corresponding Front Panel

Terminals
Objects on the front panel window appear as terminals on the block diagram.Terminals are entry and exit ports that exchange information between the front panel and block diagram. Terminals are analogous to parameters and constants in text-based programming languages. Types of terminals include control or indicator terminals and node terminals. Control and indicator terminals belong to front panel controls and indicators. Data you enter into the front panel controls (a and b in the previous front panel) enter the block diagram through the control terminals. The data then enter the Add and Subtract functions. When the Add and Subtract functions complete their calculations, they produce new data values. The data values flow to the indicator terminals, where they update the front panel indicators (a+b and a-b in the previous front panel). The terminals in Figure 2-15 belong to four front panel controls and indicators. Because terminals represent the inputs and outputs of your VI, subVIs and functions also have terminals shown at left. For example, the

LabVIEW Introduction Course Manual

2-20

ni.com

Lesson 2

Navigating LabVIEW

connector panes of the Add and Subtract functions have three node terminals. To display the terminals of the function on the block diagram, right-click the function node and select Visible ItemsTerminals from the shortcut menu.

Controls, Indicators, and Constants

Controls, indicators, and constants behave as inputs and outputs of the block diagram algorithm. Consider the implementation of the algorithm for the area of a triangle:
Area = .5 * Base * Height

In this algorithm, Base and Height are inputs and Area is an output, as shown in Figure 2-16.

Figure 2-16. Area of a Triangle Front Panel

The constant .5 does not necessarily appear on the front panel window, except possibly as documentation of the algorithm. Figure 2-17 shows a possible implementation of this algorithm on a LabVIEW block diagram. This block diagram has four different terminals created by two controls, one constant, and one indicator.

National Instruments Corporation

2-21

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Controls

Indicators

Constant

Figure 2-17. Area of a Triangle Block Diagram with Icon Terminal View

Notice that the Base (cm) and Height (cm) block diagram terminals have a different appearance from the Area (cm2) terminal. There are two distinguishing characteristics between a control and an indicator on the block diagram. The first is an arrow on the terminal that indicates the direction of data flow. The controls have arrows showing the data leaving the terminal, whereas the indicator has an arrow showing the data entering the terminal. The second distinguishing characteristic is the border around the terminal. Controls have a thick border and indicators have a thin border. You can view terminals with or without icon view. Figure 2-18 shows the same block diagram without using the icon view of the terminals; however, the same distinguishing characteristics between controls and indicators exist.

Figure 2-18. Area of a Triangle Block Diagram without Icon Terminal View

LabVIEW Introduction Course Manual

2-22

ni.com

Lesson 2

Navigating LabVIEW

Block Diagram Nodes

Nodes are objects on the block diagram that have inputs and/or outputs and perform operations when a VI runs. They are analogous to statements, operators, functions, and subroutines in text-based programming languages. Nodes can be functions, subVIs, or structures. Structures are process control elements, such as Case structures, For Loops, or While Loops. The Add and Subtract functions in the previous figure are function nodes.

Functions
Functions are the fundamental operating elements of LabVIEW. Functions do not have front panel windows or block diagram windows but do have connector panes. Double-clicking a function only selects the function. A function has a pale yellow background on its icon.

SubVIs
SubVIs are VIs that you create to use inside of another VI or that you access on the Functions palette. Any VI has the potential to be used as a subVI. When you double-click a subVI on the block diagram, its front panel window appears. The front panel includes controls and indicators. The block diagram includes wires, icons, functions, possibly subVIs, and other LabVIEW objects. The upper right corner of the front panel window and block diagram window displays the icon for the VI. This is the icon that appears when you place the VI on a block diagram as a subVI. SubVIs also can be Express VIs. Express VIs are nodes that require minimal wiring because you configure them with dialog boxes. Use Express VIs for common measurement tasks. You can save the configuration of an Express VI as a subVI. Refer to the Express VIs topic of the LabVIEW Help for more information about creating a subVI from an Express VI configuration. LabVIEW uses colored icons to distinguish between Express VIs and other VIs on the block diagram. Icons for Express VIs appear on the block diagram as icons surrounded by a blue field whereas subVI icons have a yellow field.

Expandable Nodes versus Icons

You can display VIs and Express VIs as icons or as expandable nodes. Expandable nodes appear as icons surrounded by a colored field. SubVIs appear with a yellow field, and Express VIs appear with a blue field. Use icons if you want to conserve space on the block diagram. Use expandable nodes to make wiring easier and to aid in documenting block diagrams. By default, subVIs appear as icons on the block diagram, and Express VIs appear as expandable nodes. To display a subVI or Express VI as an

National Instruments Corporation

2-23

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

expandable node, right-click the subVI or Express VI and remove the checkmark next to the View As Icon shortcut menu item. You can resize the expandable node to make wiring even easier, but it also takes a large amount of space on the block diagram. Complete the following steps to resize a node on the block diagram. 1. Move the Positioning tool over the node. Resizing handles appear at the top and bottom of the node. 2. Move the cursor over a resizing handle to change the cursor to the resizing cursor. 3. Use the resizing cursor to drag the border of the node down to display additional terminals. 4. Release the mouse button. To cancel a resizing operation, drag the node border past the block diagram window before you release the mouse button. The following figure shows the Basic Function Generator VI as a resized expandable node.

Figure 2-19. Basic Function Generator VI in Different Display Modes Note

If you display a subVI or Express VI as an expandable node, you cannot display the terminals for that node and you cannot enable database access for that node.

LabVIEW Introduction Course Manual

2-24

ni.com

Lesson 2

Navigating LabVIEW

Wires
You transfer data among block diagram objects through wires. In Figure 2-15, wires connect the control and indicator terminals to the Add and Subtract function. Each wire has a single data source, but you can wire it to many VIs and functions that read the data. Wires are different colors, styles, and thicknesses, depending on their data types. A broken wire appears as a dashed black line with a red X in the middle, as shown at left. Broken wires occur for a variety of reasons, such as when you try to wire two objects with incompatible data types. Table 2-1 shows the most common wire types.
Table 2-1. Common Wire Types

Wire Type Numeric

Scalar

1D Array

2D Array

Color Orange (floating-point), Blue (integer) Green Pink

Boolean String

In LabVIEW, you use wires to connect multiple terminals together to pass data in a VI. You must connect the wires to inputs and outputs that are compatible with the data that is transferred with the wire. For example, you cannot wire an array output to a numeric input. In addition the direction of the wires must be correct. You must connect the wires to only one input and at least one output. For example, you cannot wire two indicators together. The components that determine wiring compatibility include the data type of the control and/or the indicator and the data type of the terminal.

Data Types
Data types indicate what objects, inputs, and outputs you can wire together. For example, if a switch has a green border, you can wire a switch to any input with a green label on an Express VI. If a knob has an orange border, you can wire a knob to any input with an orange label. However, you cannot wire an orange knob to an input with a green label. Notice the wires are the same color as the terminal.

Automatically Wiring Objects

As you move a selected object close to other objects on the block diagram, LabVIEW draws temporary wires to show you valid connections. When you release the mouse button to place the object on the block diagram, LabVIEW automatically connects the wires. You also can automatically

National Instruments Corporation

2-25

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

wire objects already on the block diagram. LabVIEW connects the terminals that best match and does not connect the terminals that do not match. Toggle automatic wiring by pressing the spacebar while you move an object using the Positioning tool. By default, automatic wiring is enabled when you select an object from the Functions palette or when you copy an object already on the block diagram by pressing the <Ctrl> key and dragging the object. Automatic wiring is disabled by default when you use the Positioning tool to move an object already on the block diagram. You can adjust the automatic wiring settings by selecting ToolsOptions and selecting Block Diagram from the Category list.

Manually Wiring Objects

When you pass the Wiring tool over a terminal, a tip strip appears with the name of the terminal. In addition, the terminal blinks in the Context Help window and on the icon to help you verify that you are wiring to the correct terminal. To wire objects together, pass the Wiring tool over the first terminal, click, pass the cursor over the second terminal, and click again. After wiring, you can right-click the wire and select Clean Up Wire from the shortcut menu to have LabVIEW automatically choose a path for the wire. If you have broken wires to remove, press <Ctrl-B> to delete all the broken wires on the block diagram.

Functions Palette
The Functions palette contains the VIs, functions and constants you use to create the block diagram. You access the Functions palette from the block diagram by selecting ViewFunctions Palette. The Functions palette is broken into various categories; you can show and hide categories to suit your needs. Figure 2-20 shows a Functions palette with all of the categories exposed and the Programming category expanded. During this course, you work mostly in the Programming category, but you also use other categories, or subpalettes.

LabVIEW Introduction Course Manual

2-26

ni.com

Lesson 2

Navigating LabVIEW

Figure 2-20. Functions Palette

To view or hide categories, click the View button on the palette, and select or deselect the Always Visible Categories option. You learn more about using the Functions palette in Exercise 2-2.

Block Diagram Toolbar

When you run a VI, buttons appear on the block diagram toolbar that you can use to debug the VI. The following toolbar appears on the block diagram.

Click the Highlight Execution button to display an animation of the block diagram execution when you run the VI. Notice the flow of data through the block diagram. Click the button again to disable execution highlighting. Click the Retain Wire Values button to save the wire values at each point in the flow of execution so that when you place a probe on the wire you can immediately retain the most recent value of the data that passed through the wire. You must successfully run the VI at least once before you can retain the wire values. Click the Step Into button to open a node and pause. When you click the Step Into button again, it executes the first action and pauses at the next action of the subVI or structure. You also can press the <Ctrl> and down

National Instruments Corporation

2-27

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

arrow keys. Single-stepping through a VI steps through the VI node by node. Each node blinks to denote when it is ready to execute. Click the Step Over button to execute a node and pause at the next node. You also can press the <Ctrl> and right arrow keys. By stepping over the node, you execute the node without single-stepping through the node. Click the Step Out button to finish executing the current node and pause. When the VI finishes executing, the Step Out button is dimmed. You also can press the <Ctrl> and up arrow keys. By stepping out of a node, you complete single-stepping through the node and navigate to the next node. The Warning button appears if a VI includes a warning and you placed a checkmark in the Show Warnings checkbox in the Error List window. A warning indicates there is a potential problem with the block diagram, but it does not stop the VI from running.

LabVIEW Introduction Course Manual

2-28

ni.com

Lesson 2

Navigating LabVIEW

Exercise 2-1
Goal

Concept: Exploring a VI
Identify the parts of an existing VI.

Description
You received a VI from an employee that takes the seconds until a plane arrives at an airport and converts the time into a combination of hours/minutes/seconds. You must evaluate this VI to see if it works as expected and can display the remaining time until the plane arrives. 1. Using Windows Explorer, navigate to the <Exercises>\LabVIEW Basics I\Exploring a VI directory. Folder names in angle brackets, such as <Exercises>, refer to folders on the root directory of your computer.
Note

2. Double-click Exploring_a_VI.exe to open the simulation. 3. Follow the instructions given in the simulation. 4. Open Seconds Breakdown.vi in the <Exercises>\LabVIEW Basics I\Exporing a VI directory. This is the LabVIEW VI shown in the simulation. 5. Test the VI using the values given in Table 2-2. Enter the input value in the Total Time in Seconds control. Click the Run button. For each input, compare the given outputs to the outputs listed in Table 2-2. If the VI works correctly, they should match.
Table 2-2. Testing Values for Seconds Breakdown.vi

Input 0 seconds 60 seconds 3600 seconds 3665 seconds

Output 0 hours, 0 minutes, 0 seconds 0 hours, 1 minute, 0 seconds 1 hour, 0 minutes, 0 seconds 1 hour, 1 minutes, 5 seconds

End of Exercise 2-1

National Instruments Corporation

2-29

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

G. Searching for Controls, VIs, and Functions

When you select ViewControls or ViewFunctions to open the Controls and Functions palettes, two buttons appear at the top of the palette. SearchChanges the palette to search mode so you can perform text-based searches to locate controls, VIs, or functions on the palettes. While a palette is in search mode, click the Return button to exit search mode and return to the palette. ViewProvides options for selecting a format for the current palette, showing and hiding categories for all palettes, and sorting items in the Text and Tree formats alphabetically. Select Options from the shortcut menu to display the Controls/Functions Palettes page of the Options dialog box, in which you can select a format for all palettes. This button appears only if you click the thumbtack in the upper left corner of a palette to pin the palette. Until you are familiar with the location of VIs and functions, search for the function or VI using the Search button. For example, if you want to find the Random Number function, click the Search button on the Functions palette toolbar and start typing Random Number in the text box at the top of the palette. LabVIEW lists all matching items that either start with or contain the text you typed. You can click one of the search results and drag it to the block diagram, as shown in Figure 2-21.

Figure 2-21. Searching for an Object in the Functions Palette

LabVIEW Introduction Course Manual

2-30

ni.com

Lesson 2

Navigating LabVIEW

Double-click the search result to highlight its location on the palette. If the object is one you need to use frequently, you can add it to your Favorites category. Right-click the object on the palette and select Add Item to Favorites, as shown in Figure 2-22.

Figure 2-22. Adding an Item to the Favorites Category of a Palette

National Instruments Corporation

2-31

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Exercise 2-2
Goal

Concept: Navigating Palettes

Learn to find controls and functions.

Description
1. Open Navigating Palettes.exe in the <Exercises>\LabVIEW Basics I\Navigating Palettes directory. 2. Follow the instructions given. This simulation demonstrates how to find a control or function. 3. Using the instructions given in the simulation, place the DAQ Assistant Express VI in the Favorites category of the Functions palette.

End of Exercise 2-2

LabVIEW Introduction Course Manual

2-32

ni.com

Lesson 2

Navigating LabVIEW

H. Selecting a Tool
You can create, modify and debug VIs using the tools provided by LabVIEW. A tool is a special operating mode of the mouse cursor. The operating mode of the cursor corresponds to the icon of the tool selected. LabVIEW chooses which tool to select based on the current location of the mouse.

Figure 2-23. Tools Palette Tip You can manually choose the tool you need by selecting it on the Tools palette. Select ViewTools Palette to display the Tools palette.

National Instruments Corporation

2-33

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Operating Tool
When the mouse cursor changes to the icon shown at left, the Operating tool is in operation. Use the Operating tool to change the values of a control. For example, in Figure 2-24 the Operating tool moves the pointer on the Horizontal Pointer Slide. When the mouse hovers over the pointer, the cursor automatically accesses the Operating tool.

Figure 2-24. Using the Operating Tool

The Operating tool is mostly used on the front panel window, but you also can use the Operating tool on the block diagram window to change the value of a Boolean constant.

LabVIEW Introduction Course Manual

2-34

ni.com

Lesson 2

Navigating LabVIEW

Positioning Tool
When the mouse cursor changes to the icon shown at left, the Positioning tool is in operation. Use the Positioning tool to select or resize objects. For example, in Figure 2-25 the Positioning tool selects the Number of Measurements numeric control. After selecting an object, you can move, copy, or delete the object. When the mouse hovers over the edge of an object, the cursor automatically accesses the Positioning tool.

Figure 2-25. Using the Positioning Tool to Select an Object

National Instruments Corporation

2-35

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

If the mouse hovers over a resizing node of an object, the cursor mode changes to show that you can resize the object, as shown in Figure 2-26. Notice that the cursor is hovering over a corner of the XY Graph at a resizing node, and the cursor mode changes to a double-sided arrow.

Figure 2-26. Using the Positioning Tool to Resize an Object

You can use the Positioning tool on both the front panel window and the block diagram.

LabVIEW Introduction Course Manual

2-36

ni.com

Lesson 2

Navigating LabVIEW

Labeling Tool
When the mouse cursor changes to the icon shown at left, the Labeling tool is in operation. Use the Labeling tool to enter text in a control, to edit text, and to create free labels. For example, in Figure 2-27 the Labeling tool enters text in the Number of Measurements numeric control. When the mouse hovers over the interior of the control, the cursor automatically accesses the Labeling tool. Click once to place a cursor inside the control. Then double-click to select the current text.

Figure 2-27. Using the Labeling Tool

When you are not in a specific area of a front panel window or block diagram window that accesses a certain mouse mode, the cursor appears as cross-hairs. If automatic tool selection is enabled, you can double-click any open space to access the Labeling tool and create a free label.

National Instruments Corporation

2-37

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Wiring Tool
When the mouse cursor changes to the icon shown at left, the Wiring tool is in operation. Use the Wiring tool to wire objects together on the block diagram. For example, in Figure 2-28 the Wiring tool wires the Number of Measurements terminal to the count terminal of the For Loop. When the mouse hovers over the exit or entry point of a terminal or over a wire, the cursor automatically accesses the Wiring tool.

Figure 2-28. Using the Wiring Tool

The Wiring tool works mainly with the block diagram window and when you create a connector pane on the front panel window.

LabVIEW Introduction Course Manual

2-38

ni.com

Lesson 2

Navigating LabVIEW

Other Tools Accessed from the Palette

You can access the Operating, Positioning, Labeling, and Wiring tools directly from the Tools palette, rather than using the Automatic tool selection mode. Select ViewTools Palette to access the Tools palette.

Figure 2-29. The Tools Palette

The top item in the Tools palette is the Automatic Tool Selection button. When this is selected, LabVIEW automatically chooses a tool based on the location of your cursor. You can turn off automatic tool selection by deselecting the item, or by selecting another item in the palette. There are some additional tools on the palette, as described below: Use the Object Shortcut Menu tool to access an object shortcut menu with the left mouse button. Use the Scrolling tool to scroll through windows without using scrollbars. Use the Breakpoint tool to set breakpoints on VIs, functions, nodes, wires, and structures to pause execution at that location. Use the Probe tool to create probes on wires on the block diagram. Use the Probe tool to check intermediate values in a VI that produces questionable or unexpected results. Use the Color Copy tool to copy colors for pasting with the Coloring tool. Use the Coloring tool to color an object. The Coloring tool also displays the current foreground and background color settings.

National Instruments Corporation

2-39

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Exercise 2-3
Goal

Concept: Selecting a Tool

Become familiar with automatic tool selection in LabVIEW.

Description
During this exercise, you complete tasks in a partially built front panel and block diagram. These tasks give you experience using the automatic tool selection. 1. Open Using Temperature.vi. Open LabVIEW. Select FileOpen. Navigate to the <Exercises>\LabVIEW Basics I\Using Temperature directory. Select Using Temperature.vi and click OK. Figure 2-30 shows an example of the front panel as it appears after your modifications. You increase the size of the waveform graph, rename the numeric control, change the value of the numeric control, and move the pointer on the horizontal pointer slide.

Figure 2-30. Using Temperature VI Front Panel

LabVIEW Introduction Course Manual

2-40

ni.com

Lesson 2

Navigating LabVIEW

2. Expand the waveform graph horizontally using the Positioning tool. Move the cursor to the left edge of the Waveform Graph. Move the cursor to the middle left resizing node until the cursor changes to a double arrow, as shown in Figure 2-31.

Figure 2-31. Resize Waveform Graph

Drag the repositioning point until the Waveform Graph is the size you want. 3. Rename the numeric control to Number of Measurements using the Labeling Tool. Move the cursor to the text Numeric. Double click the word Numeric. Enter the text Number of Measurements. 4. Complete the entry by pressing the <Enter> key on the numeric keypad, clicking the Enter Text button on the toolbar, or clicking outside the control. Change the value of the Number of Measurements control to 20 using the Labeling tool. Move the cursor to the interior of the numeric control. When the cursor changes to the Labeling tool icon, as shown at left, click the mouse button. Enter the text 20.

National Instruments Corporation

2-41

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Complete the entry by pressing the <Enter> key on the numeric keypad, clicking the Enter Text button on the toolbar, or clicking outside the control. 5. Change the value of the pointer on the horizontal pointer slide using the Operating tool. Move the cursor to the pointer on the slide. When the cursor changes to the Operating tool icon, as shown at left, press the mouse button and drag to the value you want. Leave the value at a value greater than 0. 6. Try changing the value of objects, resizing objects, and renaming objects until you are comfortable with using these tools. Figure 2-32 shows an example of the block diagram as it appears after your modifications. You move the Number of Measurements terminal and wire the terminal to the count terminal of the For Loop.

Figure 2-32. Using Temperature VI Block Diagram

7. Open the block diagram. 8. Move the Number of Measurements terminal using the Positioning tool. Move the cursor to the Number of Measurements terminal. Move the cursor in the terminal until the cursor changes to an arrow, as shown at left. Click and drag the terminal to the new location as shown in Figure 2-32.

LabVIEW Introduction Course Manual

2-42

ni.com

Lesson 2

Navigating LabVIEW

9. Wire the Number of Measurements terminal to the count terminal of the For Loop using the Wiring tool. Move the cursor to the Number of Measurements terminal. Move the cursor to the right of the terminal, stopping when the cursor changes to a wiring spool, as shown at left. Click to start the wire. Move the cursor to the count (N) terminal of the For Loop. Click the count terminal to end the wire. 10. Click the Run button to run the VI. The time required to execute this VI is equivalent to Number of Measurements times Delay (Sec). Once the VI is finished executing, the data is displayed on the Temperature Graph. 11. Try moving other objects, deleting wires and rewiring them, and wiring objects and wires together until you are comfortable with using these tools. 12. Select FileClose to close the VI and click the Dont save - All button. You do not need to save the VI.

End of Exercise 2-3

National Instruments Corporation

2-43

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

I. Data Flow
LabVIEW follows a dataflow model for running VIs. A block diagram node executes when it receives all required inputs. When a node executes, it produces output data and passes the data to the next node in the dataflow path. The movement of data through the nodes determines the execution order of the VIs and functions on the block diagram. Visual Basic, C++, JAVA, and most other text-based programming languages follow a control flow model of program execution. In control flow, the sequential order of program elements determines the execution order of a program. For a dataflow programming example, consider a block diagram that adds two numbers and then subtracts 50.00 from the result of the addition, as shown in Figure 2-33. In this case, the block diagram executes from left to right, not because the objects are placed in that order, but because the Subtract function cannot execute until the Add function finishes executing and passes the data to the Subtract function. Remember that a node executes only when data are available at all of its input terminals and supplies data to the output terminals only when the node finishes execution.

Figure 2-33. Dataflow Programming Example

LabVIEW Introduction Course Manual

2-44

ni.com

Lesson 2

Navigating LabVIEW

In Figure 2-34, consider which code segment would execute firstthe Add, Random Number, or Divide function. You cannot know because inputs to the Add and Divide functions are available at the same time, and the Random Number function has no inputs. In a situation where one code segment must execute before another, and no data dependency exists between the functions, use other programming methods, such as error clusters, to force the order of execution. Refer to Lesson 5, Relating Data, for more information about error clusters.

Figure 2-34. Dataflow Example for Multiple Code Segments

National Instruments Corporation

2-45

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Exercise 2-4
Goal

Concept: Data Flow

Understand how data flow determines the execution order in a VI.

Description
1. Open the Dataflow.exe simulation from the <Exercises>\ LabVIEW Basics I\Dataflow directory. 2. Follow the instructions given. This simulation demonstrates data flow.

End of Exercise 2-4

LabVIEW Introduction Course Manual

2-46

ni.com

Lesson 2

Navigating LabVIEW

J. Creating a Simple VI
Most LabVIEW VIs have three main tasksacquiring some sort of data, analyzing the acquired data, and presenting the result. When each of these parts are simple, you can complete the entire VI using very few objects on the block diagram. Express VIs are designed specifically for completing common, frequently used operations. In this section, you learn about some Express VIs that acquire, analyze, and present data. Then you learn to create a simple VI that uses these three tasks, as shown in Figure 2-35.

Figure 2-35. Acquire, Analyze, and Present Example Front Panel Window and Block Diagram Window

National Instruments Corporation

2-47

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

On the Functions palette, the Express VIs are grouped together in the Express category. Express VIs use the dynamic data type to pass data between Express VIs.

Acquire
Express VIs used for the Acquire task include the following: DAQ Assistant, Instrument I/O Assistant, Simulate Signal, and Read from Measurement File.

DAQ Assistant
The DAQ Assistant acquires data through a data acquisition device.You must use this Express VI frequently throughout this course. Refer to Lesson 8, Acquiring Data, for more information about the DAQ Assistant. Until you learn more about data acquisition, you only use one channel of the data acquisition device, CH0. This channel is connected to a temperature sensor on the DAQ Signal Accessory. You can touch the temperature sensor to change the temperature the sensor reads.

Instrument I/O Assistant

The Instrument I/O Assistant acquires instrument control data, usually from a GPIB or serial interface. Refer to Lesson 9, Instrument Control, for more information about the Instrument I/O Assistant.

Simulate Signal
The Simulate Signal Express VI generates simulated data such as a sine wave.

Read From Measurement File

The Read From Measurement File Express VI reads a file that was created using the Write To Measurement File Express VI. It specifically reads LVM or TDM file formats. This Express VI does not read ASCII files. Refer to Lesson 6, Storing Measurement Data, for more information on reading data from a file.

Analyze
Express VIs used for the Analyze task include the followingAmplitude and Level Measurements, Statistics, Tone Measurements, and so on.

Amplitude and Level Measurements

The Amplitude and Level Measurements Express VI performs voltage measurements on a signal. These include DC, rms, maximum peak, minimum peak, peak to peak, cycle average, and cycle rms measurements.

LabVIEW Introduction Course Manual

2-48

ni.com

Lesson 2

Navigating LabVIEW

Statistics
The Statistics Express VI calculates statistical data from a waveform. This includes mean, sum, standard deviation, and extreme values.

Spectral Measurements
The Spectral Measurements Express VI performs spectral measurement on a waveform, such as magnitude and power spectral density.

Tone Measurements
The Tone Measurements Express VI searches for a single tone with the highest frequency or highest amplitude. It also finds the frequency and amplitude of a single tone.

Filter
The Filter Express VI processes a signal through filters and windows. Filters used include the following: Highpass, Lowpass, Bandpass, Bandstop, and Smoothing. Windows used include Butterworth, Chebyshev, Inverse Chebyshev, Elliptical, and Bessel.

Present
Present results by using Express VIs that perform a function, such as the Write to Measurement File Express VI, or indicators that present data on the front panel window. The most commonly used indicators for this task include the Waveform Chart, the Waveform Graph, and the XY Graph. Common Express VIs include the Write to Measurement File Express VI, the Build Text Express VI, the DAQ Assistant, and the Instrument I/O Assistant. In this case, the DAQ Assistant and the Instrument I/O Assistant provide output data from the computer to the DAQ device or an external instrument.

Write to Measurement File

The Write to Measurement File Express VI writes a file in LVM or TDMS file format. Refer to Lesson 6, Storing Measurement Data, for more information on writing to measurement files.

Build Text
The Build Text Express VI creates text, usually for displaying on the front panel window or exporting to a file or instrument. Refer to Lesson 6, Storing Measurement Data, for more information on creating strings.

National Instruments Corporation

2-49

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Running a VI
After you configure the Express VIs and wire them together, you can run the VI. When you finish creating your VI, click the Run button on the toolbar to execute the VI. While the VI is running, the Run button icon changes to the figure shown at left. After the execution completes, the Run button icon changes back to its original state, and the front panel indicators contain data.

Run Button Errors

If a VI does not run, it is a broken, or nonexecutable, VI. The Run button appears broken, shown as follows, when the VI you are creating or editing contains errors.

If the button still appears broken when you finish wiring the block diagram, the VI is broken and cannot run. Generally, this means that a required input is not wired, or a wire is broken. Press the broken run button to access the Error list window. The Error list window lists each error and describes the problem. You can double-click an error to go directly to the error. Refer to Lesson 3, Troubleshooting and Debugging VIs, for more information on debugging VIs.

LabVIEW Introduction Course Manual

2-50

ni.com

Lesson 2

Navigating LabVIEW

Exercise 2-5
Goal

Simple AAP VI
Create a simple VI that acquires, analyzes, and presents data.

Scenario
You need to acquire a sine wave for 0.1 seconds, determine and display the average value, log the data, and display the sine wave on a graph.

Design
The input for this problem is an analog channel of sine wave data. The outputs include a graph of the sine data and a file that logs the data.

Flowchart

ACQUIRE

ANALYZE

PRESENT

Acquire Data

Display Data

Log Data

Determine Average Value

Display Average Value

Figure 2-36. Simple AAP VI Flowchart

National Instruments Corporation

2-51

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Program ArchitectureQuiz
1. Acquire: Circle the Express VI that is best suited to acquiring a sine wave from a data acquisition device. DAQ Assistant The DAQ Assistant acquires data through a data acquisition device. The Instrument I/O Assistant acquires instrument control data, usually from a GPIB or serial interface. The Simulate Signal Express VI generates simulated data, such as a sine wave.

Instrument I/O Assistant Simulate Signal Express VI

2. Analyze: Circle the Express VI that is best suited to determining the average value of the acquired data. Tone Measurements Express VI Statistics Express VI The Tone Measurements Express VI finds the frequency and amplitude of a single tone. The Statistics Express VI calculates statistical data from a waveform. The Amplitude and Level Measurements Express VI performs voltage measurements on a signal. The Filter Express VI processes a signal through filters and windows.

Amplitude and Level Measurements Express VI Filter Express VI

LabVIEW Introduction Course Manual

2-52

ni.com

Lesson 2

Navigating LabVIEW

3. Present: Circle the Express VIs and/or indicators that are best suited to displaying the data on a graph and logging the data to file. DAQ Assistant The DAQ Assistant acquires data through a data acquisition device. The Write to Measurement File Express VI writes a file in LVM or TDM file format. The Build Text Express VI creates text, usually for displaying on the front panel window or exporting to a file or instrument. The waveform graph displays one or more plots of evenly sampled measurements.

Write to Measurement File Express VI Build Text Express VI

Waveform Graph

Refer to the next page for answers to this quiz.

National Instruments Corporation

2-53

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Program ArchitectureSolutions to Quiz

1. Acquire: Use the DAQ Assistant to acquire the sine wave from the data acquisition device. 2. Analyze: Use the Statistics Express VI to determine the average value of the sine wave. Because this signal is cyclical, you could also use the Cycle Average option in the Amplitude and Level Measurements Express VI to determine the average value of the sine wave. 3. Present: Use the Write to Measurement File Express VI to log the data and use the Waveform Graph to display the data on the front panel window.

LabVIEW Introduction Course Manual

2-54

ni.com

Lesson 2

Navigating LabVIEW

Implementation
1. Prepare your hardware to generate a sine wave. If you are not using hardware, skip to step 2. Find the DAQ Signal Accessory and visually confirm that it is connected to the DAQ device in your computer. Using a wire, connect the Analog In Channel 1 to the Sine Function Generator, as shown in Figure 2-37. Set the Frequency Range switch and the Frequency Adjust knob to their lowest levels.

Power Quadrature A Encoder B

B Relay DIO 5 200mA Max

A B 68-pin Device (Diff Mode) Lab/1200 Series (NRSE Mode) 50-pin MIO Device (Diff Mode) 24 Pulses/rev Digital Trigger Digital Port 0 3 2 1 0 Counters Frequency Frequency Range Adjust 13kHz-1MHz 1kHz-100kHz Lo Hi 100Hz-10kHz Analog Analog Function Out In Generator Temp Sensor Noise Off On Temp Sensor Mic Ch 6

DAQ
Signal Accessory Ch 0 1 1 2

V*100 = C Ch 0

Figure 2-37. Connection for the DAQ Signal Accessory

2. Open LabVIEW. 3. Open a blank VI.

National Instruments Corporation

2-55

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

4. Save the VI as Simple AAP.vi. Select FileSave. Navigate to the <Exercises>\LabVIEW Basics I\ Simple AAP directory. Name the VI Simple AAP.vi. Click OK. In the following steps, you will build a front panel window similar to the one in Figure 2-38.

Figure 2-38. Acquire, Analyze and Present Front Panel Window

5. Add a waveform graph to the front panel window to display the acquired data. If the Controls palette is not already open, select ViewControls Palette from the LabVIEW menu. On the Controls palette, select the Express category. Select the Graph Indicators category from within the Express category. Select the waveform graph. Add the graph to the front panel window.

LabVIEW Introduction Course Manual

2-56

ni.com

Lesson 2

Navigating LabVIEW

6. Add a numeric indicator to the front panel to display the average value. Collapse the Graph Indicators category by selecting Express on the Controls palette. Select the Numeric Indicators category from within the Express category. Select the numeric indicator. Place the indicator on the front panel. Enter Average Value in the label of the numeric indicator. In the following steps, you build a block diagram similar to the one in Figure 2-39.

Figure 2-39. Acquire, Analyze, and Present Block Diagram

7. Open the block diagram of the VI. Select WindowShow Block Diagram. The terminals corresponding to the new front panel window objects appear on the block diagram.
Note

National Instruments Corporation

2-57

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

8. Acquire a sine wave for 0.1 seconds. If you have hardware installed, follow the instructions in the Hardware Installed column to acquire the data using the DAQ Assistant. If you do not have hardware installed, follow the instructions in the No Hardware Installed column to simulate the acquisition using the Simulate Signal Express VI. Hardware Installed 1. On the Functions palette, select the Express category. 2. Select Input from the Express category. 3. Select the DAQ Assistant from the Input category. 4. Place the DAQ Assistant on the block diagram. 5. Wait for the DAQ Assistant dialog box to open. 6. Select Acquire VoltageAnalog Input Voltage for the measurement type. 7. Select ai1 (analog input channel 1) for the physical channel. 8. Click the Finish button. 9. In the Timing Setting section, tab select N Samples as the Acquisition Mode. 10. In the Timing Settings section enter 100 in Samples To Read. 11. Enter 1000 in Rate (Hz). 12. Click the OK button.
Tip

No Hardware Installed 1. On the Functions palette, select the Express category. 2. Select Input from the Express category. 3. Select Simulate Signal from the Input category. 4. Place the Simulate Signal Express VI on the block diagram. 5. Wait for the Simulate Signal dialog box to open. 6. Select Sine for the signal type. 7. Set the signal frequency to 100. 8. In the Timing section, set the Samples per second (Hz) to 1000. 9. In the Timing section, deselect Automatic for the Number of samples. 10. In the Timing section, set the Number of samples to 100. 11. Select the Simulate acquisition timing selection. 12. Click the OK button.

Reading 100 samples at a rate of 1,000 Hz retrieves 0.1 seconds worth of data. 9. Determine the average value of the data acquired by using the Statistics Express VI. Collapse the Input palette by selecting Express on the Functions palette.

LabVIEW Introduction Course Manual

2-58

ni.com

Lesson 2

Navigating LabVIEW

Select the Signal Analysis palette. Select the Statistics Express VI and add the Statistics Express VI to the block diagram to the right of the DAQ Assistant. Wait for the Statistics Express VI dialog box to open. Place a checkmark in the Arithmetic mean checkbox. Click OK. 10. Log the generated sine data to a LabVIEW Measurement File. Select Express on the Functions palette. Select the Output category. Select Write to Measurement File. Add the Write to Measurement File Express VI to the block diagram below the Statistics Express VI. Wait for the Write to Measurement File Express VI dialog box to open. Leave all settings as default. Click OK.
Note Future exercises do not detail the directions for finding specific functions or controls in the palettes. Use the palette search feature to locate functions and controls.

11. Wire the data from the DAQ Assistant (or Simulate Signal Express VI) to the Statistics Express VI. Place the mouse cursor over the data output of the DAQ Assistant (or the Sine output of the Simulate Signal Express VI) at the location where the cursor changes to the Wiring tool. Click the mouse button to start the wire. Place the mouse cursor over the Signals input of the Statistics Express VI and click the mouse button to end the wire.

National Instruments Corporation

2-59

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

12. Wire the data to the graph indicator. Place the mouse cursor over the data output wire of the DAQ Assistant (or the Sine output of the Simulate Signal Express VI) at the location where the cursor changes to the Wiring tool. Click the mouse button to start the wire. Place the mouse cursor over the graph indicator and click the mouse button to end the wire. 13. Wire the Arithmetic Mean output of the Statistics Express VI to the Average Value numeric indicator. Place the mouse cursor over the Arithmetic Mean output of the Statistics Express VI at the location where the cursor changes to the Wiring tool. Click the mouse button to start the wire. Place the mouse cursor over the Average Value numeric indicator and click the mouse button to end the wire. 14. Wire the data output to the Signals input of the Write Measurement File Express VI. Place the mouse cursor over the data output wire of the DAQ Assistant (or the Sine output of the Simulate Signal Express VI) at the location where the cursor changes to the Wiring tool. Click the mouse button to start the wire. Place the mouse cursor over the Signals input of the Write Measurement File Express VI and click the mouse button to end the wire.
Note

Future exercises do not detail the directions for wiring between objects. 15. Save the VI.

LabVIEW Introduction Course Manual

2-60

ni.com

Lesson 2

Navigating LabVIEW

Test
1. Switch to the front panel window of the VI. 2. Set the graph properties to be able to view the sine wave. Right-click the waveform graph and select X ScaleAutoscale X to disable autoscaling. Right-click the waveform graph and select Visible ItemsX Scrollbar. Use the labeling tool to change the last number on the X Scale of the waveform graph to .1. 3. Save the VI. 4. Run the VI. Click the Run button on the front panel toolbar. The graph indicator should display a sine wave and the Average Value indicator should display a number around zero. If the VI does not run as expected, review the implementation steps. 5. Close the VI.

End of Exercise 2-5

National Instruments Corporation

2-61

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Self-Review: Quiz
Refer to Figure 2-40 to answer the following quiz questions.

Figure 2-40. Dataflow Questions

1. Which function executes first? a. Add b. Subtract c. Unknown 2. Which function executes first? a. Sine b. Divide c. Unknown 3. Which function executes first? a. Random Number b. Divide c. Add d. Unknown 4. Which function executes last? a. Random Number b. Subtract c. Add d. Unknown 5. What are the three parts of a VI? a. Front panel window b. Block diagram window c. Project d. Icon/connector pane

National Instruments Corporation

2-63

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Self-Review: Quiz Answers

1. Which function executes first? a. Add b. Subtract c. Unknown 2. Which function executes first? a. Sine b. Divide c. Unknown 3. Which function executes first? a. Random Number b. Divide c. Add d. Unknown 4. Which function executes last? a. Random Number b. Subtract c. Add d. Unknown 5. What are the three parts of a VI? a. Front panel window b. Block diagram window c. Project d. Icon/connector pane

National Instruments Corporation

2-65

LabVIEW Introduction Course Manual

Lesson 2

Navigating LabVIEW

Notes

LabVIEW Introduction Course Manual

2-66

ni.com

Troubleshooting and Debugging VIs

To run a VI, you must wire all the subVIs, functions, and structures with the correct data types for the terminals. Sometimes a VI produces data or runs in a way you do not expect. You can use LabVIEW to configure how a VI runs and to identify problems with block diagram organization or with the data passing through the block diagram.

Topics
A. LabVIEW Help Utilities B. Correcting Broken VIs C. Debugging Techniques D. Undefined or Unexpected Data E. Error Checking and Error Handling

National Instruments Corporation

3-1

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

A. LabVIEW Help Utilities

Use the Context Help window, the LabVIEW Help, and the NI Example Finder to help you create and edit VIs. Refer to the LabVIEW Help and manuals for more information about LabVIEW.

Context Help Window

The Context Help window displays basic information about LabVIEW objects when you move the cursor over each object. To toggle display of the Context Help window select HelpShow Context Help, press the <Ctrl-H> keys, or click the Show Context Help Window button on the toolbar. When you move the cursor over front panel and block diagram objects, the Context Help window displays the icon for subVIs, functions, constants, controls, and indicators, with wires attached to each terminal. When you move the cursor over dialog box options, the Context Help window displays descriptions of those options. In the Context Help window, the labels of required terminals appear bold, recommended terminals appear as plain text, and optional terminals appear dimmed. The labels of optional terminals do not appear if you click the Hide Optional Terminals and Full Path button, shown as follows, in the Context Help window.

Figure 3-1. Context Help Window

Click the Show Optional Terminals and Full Path button located on the lower left corner of the Context Help window to display the optional terminals of a connector pane and to display the full path to a VI. Optional

LabVIEW Introduction Course Manual

3-2

ni.com

Lesson 3

Troubleshooting and Debugging VIs

terminals are shown by wire stubs, informing you that other connections exist. The detailed mode displays all terminals, as shown in Figure 3-2.

Figure 3-2. Detailed Context Help Window

Click the Lock Context Help button to lock the current contents of the Context Help window. When the contents are locked, moving the cursor over another object does not change the contents of the window. To unlock the window, click the button again. You also can access this option from the Help menu. If a corresponding LabVIEW Help topic exists for an object the Context Help window describes, a blue Click here for more help link appears in the Context Help window. Also, the More Help button is enabled. Click the link or the button to display the LabVIEW Help for more information about the object.

LabVIEW Help
You can access the LabVIEW Help by clicking the More Help button in the Context Help window, selecting HelpSearch the LabVIEW Help, or clicking the blue Click here for more help link in the Context Help window. You also can right-click an object and select Help from the shortcut menu. The LabVIEW Help contains detailed descriptions of most palettes, menus, tools, VIs, and functions. The LabVIEW Help also includes step-by-step instructions for using LabVIEW features. The LabVIEW Help includes links to the following resources: LabVIEW Documentation Resources, which describes online and print documents to help new and experienced users, which includes PDF versions of all LabVIEW manuals.

National Instruments Corporation

3-3

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Technical support resources on the National Instruments Web site, such as the NI Developer Zone, the KnowledgeBase, and the Product Manuals Library.

NI Example Finder
Use the NI Example Finder to browse or search examples installed on your computer or on the NI Developer Zone at ni.com/zone. These examples demonstrate how to use LabVIEW to perform a wide variety of test, measurement, control, and design tasks. Select HelpFind Examples or click the Find Examples link in the Examples section of the Getting Started window to launch the NI Example Finder. Examples can show you how to use specific VIs or functions. You can right-click a VI or function on the block diagram or on a pinned palette and select Examples from the shortcut menu to display a help topic with links to examples for that VI or function. You can modify an example VI to fit an application, or you can copy and paste from one or more examples into a VI that you create.

Figure 3-3. NI Example Finder

LabVIEW Introduction Course Manual

3-4

ni.com

Lesson 3

Troubleshooting and Debugging VIs

Exercise 3-1
Goal

Concept: Using Help

Become familiar with using the Context Help window, the LabVIEW Help, and the NI Example Finder.

Description
This exercise consists of a series of tasks designed to help you become familiar with the LabVIEW Help tools. Complete the following steps.

NI Example Finder
1. You have a GPIB device in your computer, and you want to learn how to communicate with it using LabVIEW. Use the NI Example Finder to find a VI that communicates with a GPIB device. Open LabVIEW. Select HelpFind Examples to open the NI Example Finder. Confirm that the Task option is selected on the Browse tab. Double-click the Hardware Input and Output task to find examples related to hardware input and output. Double-click the GPIB task. Select one of the VIs shown in this directory. Notice that a description of the VI is provided in the Information window so that you can verify that this VI meets your needs. Double-click the VI name to open the VI. Close the VI after you finish exploring it. 2. You want to learn more about using Express VIs to filter signals. Use the NI Example Finder to find an appropriate VI. The NI Example Finder should still be open from the previous step. If not, open the NI Example Finder. Click the Search tab in the NI Example Finder. Enter express in the Enter keyword(s) field to find VIs that contain Express VIs.

National Instruments Corporation

3-5

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Double-click the Express result that appears in the Double-click keyword(s) field. This keyword is associated with many example VIs, as demonstrated by the number of VIs returned. You can select any one of these VIs and read the description in the Information window. Double-click Express Filter.vi to open it.

Context Help Window

3. Use the Context Help window to learn about the Express VIs used in the Express Filter VI. Open the block diagram by selecting WindowShow Block Diagram. Open the Context Help window by selecting HelpShow Context Help. Move the Context Help window to a convenient area where the window does not hide part of the block diagram. Place your mouse cursor over the Simulate Signal Express VI. The Context Help window content changes to show information about the object that your mouse is over. Move your mouse over another Express VI. Notice the Context Help window content changes corresponding to the location of the mouse cursor. Move your mouse over one of the Tone Measurements Express VIs. Examine the configuration details in the Context Help window. This gives you the information about how the Express VI is configured. Double-click the Tone Measurements Express VI to open the configuration dialog box. Notice that the selections in the configuration dialog box match the information in the Context Help window. Click the OK button to close the configuration dialog box.

LabVIEW Introduction Course Manual

3-6

ni.com

Lesson 3

Troubleshooting and Debugging VIs

4. Anchor the Context Help window so that you can move your mouse without the contents of the window changing. The Context Help window should show information about the Simulate Signal Express VI. Move your mouse over the Simulate Signal Express VI. To anchor the context help window, select the Lock button in the lower left corner of the window.
Tip If the contents of the window change before you lock the window, avoid passing your mouse over other objects on the way to the Context Help window. Move the window closer to the object of interest to view Context Help for that item.

Move your mouse over another object. Notice the contents of the window do not change while the Lock button is selected. Deselect the Lock button to resume normal operation of the window. 5. Modify the Description and Tip associated with the Simulated frequency control to change the content shown in the Context Help window. Select WindowShow Front Panel to open the front panel of the VI. Move your mouse over the Simulated frequency control. Read the contents of the Context Help window. Right-click the Simulated frequency control. Select Description and Tip from the shortcut menu. Replace the text in the "Simulated frequency" Description box with the text This is the description of the control. Replace the text in the "Simulated frequency" Tip box with the text This is the tip for the control. Click the OK button. Move your mouse over the Simulated frequency control. Notice that the contents of the Context Help window changed to match the text you typed in the Description field of the Description and Tip dialog box. Run the VI.

National Instruments Corporation

3-7

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Place your mouse cursor over the Simulated frequency control. Notice that the tool tip that appears matches the text you typed in the Tip field of the Description and Tip dialog box. Click the Stop button.

LabVIEW Help
6. Use the LabVIEW Help to learn more information about the Filter Express VI. Select WindowShow Block Diagram to open the block diagram of the Express Filter VI. Right-click the Filter Express VI and select Help from the shortcut menu. This opens the LabVIEW Help topic for the Filter Express VI. To access the LabVIEW Help for this topic, you can also select the Detailed Help link in the Context Help window while the Filter Express VI is selected, or click the question mark in the Context Help window.
Note

Explore the topic. For example, what is the purpose of the Phase Response dialog box option? Close the LabVIEW Help window. 7. Close the Express Filter VI when you finish. Do not save changes.

End of Exercise 3-1

LabVIEW Introduction Course Manual

3-8

ni.com

Lesson 3

Troubleshooting and Debugging VIs

B. Correcting Broken VIs

If a VI does not run, it is a broken, or nonexecutable, VI. The Run button appears broken, shown as follows, when the VI you are creating or editing contains errors.

If the button still appears broken when you finish wiring the block diagram, the VI is broken and cannot run.

Finding Causes for Broken VIs

Warnings do not prevent you from running a VI. They are designed to help you avoid potential problems in VIs. Errors, however, can break a VI. You must resolve any errors before you can run the VI. Click the broken Run button or select ViewError List to find out why a VI is broken. The Error list window lists all the errors. The Items with errors section lists the names of all items in memory, such as VIs and project libraries that have errors. If two or more items have the same name, this section shows the specific application instance for each item. The errors and warnings section lists the errors and warnings for the VI you select in the Items with errors section. The Details section describes the errors and in some cases recommends how to correct the errors. Click the Help button to display a topic in the LabVIEW Help that describes the error in detail and includes step-by-step instructions for correcting the error. Click the Show Error button or double-click the error description to highlight the area on the block diagram or front panel that contains the error.

National Instruments Corporation

3-9

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Figure 3-4. Example of the Error List Dialog Box

Common Causes of Broken VIs

The following list contains common reasons why a VI is broken while you edit it: The block diagram contains a broken wire because of a mismatch of data types or a loose, unconnected end. Refer to the Correcting Broken Wires topic of the LabVIEW Help for information about correcting broken wires. A required block diagram terminal is unwired. Refer to the Using Wires to Link Block Diagram Objects topic of the LabVIEW Help for information about setting required inputs and outputs. A subVI is broken or you edited its connector pane after you placed its icon on the block diagram of the VI. Refer to the Creating SubVIs topic of the LabVIEW Help for information about subVIs.

LabVIEW Introduction Course Manual

3-10

ni.com

Lesson 3

Troubleshooting and Debugging VIs

C. Debugging Techniques
If a VI is not broken, but you get unexpected data, you can use the following techniques to identify and correct problems with the VI or the block diagram data flow: Wire the error in and error out parameters at the bottom of most built-in VIs and functions. These parameters detect errors encountered in each node on the block diagram and indicate if and where an error occurred. You also can use these parameters in the VIs you build. To eliminate all VI warnings, select ViewError List and place a checkmark in the Show Warnings checkbox to see all warnings for the VI. Determine the causes and correct them in the VI. Triple-click the wire with the Operating tool to highlight its entire path and to ensure that the wires connect to the proper terminals. Use the Context Help window to check the default values for each function and subVI on the block diagram. VIs and functions pass default values if recommended or optional inputs are unwired. For example, a Boolean input might be set to TRUE if unwired. Use the Find dialog box to search for subVIs, text, and other objects to correct throughout the VI. Select ViewBrowse RelationshipsThis VI's Hierarchy to find unwired subVIs. Unlike unwired functions, unwired VIs do not always generate errors unless you configure an input to be required. If you mistakenly place an unwired subVI on the block diagram, it executes when the block diagram does. Consequently, the VI might perform extra actions. Use execution highlighting to watch the data move through the block diagram. Single-step through the VI to view each action of the VI on the block diagram. Use the Probe tool to observe intermediate data values and to check the error output of VIs and functions, especially those performing I/O. Use breakpoints to pause execution, so you can single-step or insert probes. Suspend the execution of a subVI to edit values of controls and indicators, to control the number of times it runs, or to go back to the beginning of the execution of the subVI. Determine if the data that one function or subVI passes is undefined. This often happens with numbers. For example, at one point in the VI an operation could have divided a number by zero, thus returning Inf (infinity), whereas subsequent functions or subVIs were expecting numbers.
3-11 LabVIEW Introduction Course Manual

National Instruments Corporation

Lesson 3

Troubleshooting and Debugging VIs

If the VI runs more slowly than expected, confirm that you turned off execution highlighting in subVIs. Also, close subVI front panels and block diagrams when you are not using them because open windows can affect execution speed. Check the representation of controls and indicators to see if you are receiving overflow because you converted a floating-point number to an integer or an integer to a smaller integer. For example, you might wire a 16-bit integer to a function that only accepts 8-bit integers. This causes the function to convert the 16-bit integer to an 8-bit representation, potentially causing a loss of data. Determine if any For Loops inadvertently execute zero iterations and produce empty arrays. Verify you initialized shift registers properly unless you intend them to save data from one execution of the loop to another. Check the cluster element order at the source and destination points. LabVIEW detects data type and cluster size mismatches at edit time, but it does not detect mismatches of elements of the same type. Check the node execution order. Check that the VI does not contain hidden subVIs. You inadvertently might have hidden a subVI by placing one directly on top of another node or by decreasing the size of a structure without keeping the subVI in view. Check the inventory of subVIs the VI uses against the results of ViewBrowse RelationshipsThis VI's SubVIs and ViewBrowse RelationshipsUnopened SubVIs to determine if any extra subVIs exist. Also open the VI Hierarchy window to see the subVIs for a VI. To help avoid incorrect results caused by hidden VIs, specify that inputs to VIs are required.

Execution Highlighting
View an animation of the execution of the block diagram by clicking the Highlight Execution button, shown as follows.

Execution highlighting shows the movement of data on the block diagram from one node to another using bubbles that move along the wires. Use execution highlighting in conjunction with single-stepping to see how data values move from node to node through a VI.
Note

Execution highlighting greatly reduces the speed at which the VI runs.

LabVIEW Introduction Course Manual

3-12

ni.com

Lesson 3

Troubleshooting and Debugging VIs

Figure 3-5. Example of Execution Highlighting in Use

Single-Stepping
Single-step through a VI to view each action of the VI on the block diagram as the VI runs. The single-stepping buttons, shown as follows, affect execution only in a VI or subVI in single-step mode.

Enter single-step mode by clicking the Step Into or Step Over button on the block diagram toolbar. Move the cursor over the Step Into, Step Over, or Step Out button to view a tip strip that describes the next step if you click that button. You can single-step through subVIs or run them normally. If you single-step through a VI with execution highlighting on, an execution glyph, shown as follows, appears on the icons of the subVIs that are currently running.

Probe Tools
Use the Probe tool, shown as follows, to check intermediate values on a wire as a VI runs. You also can use the Probe tool to view the data in a script in a MathScript Node as a VI runs.

Use the Probe tool if you have a complicated block diagram with a series of operations, any one of which might return incorrect data. Use the Probe tool with execution highlighting, single-stepping, and breakpoints to determine

National Instruments Corporation

3-13

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

if and where data is incorrect. If data is available, the probe immediately updates during single-stepping or when you pause at a breakpoint. When execution pauses at a node because of single-stepping or a breakpoint, you also can probe the wire that just executed to see the value that flowed through that wire. You cannot use execution highlighting, single-stepping, and breakpoints within a script in a MathScript Node.
Note

Types of Probes
You can check intermediate values on a wire when a VI runs by using a generic probe, by using an indicator on the Controls palette to view the data, by using a supplied probe, by using a customized supplied probe, or by creating a new probe. You can view the data in a script in a MathScript Node as a VI runs by using a LabVIEW MathScript probe. Generic Use the generic probe to view the data that passes through a wire. Right-click a wire and select Custom ProbeGeneric Probe from the shortcut menu to use the generic probe. The generic probe displays the data. You cannot configure the generic probe to respond to the data. LabVIEW displays the generic probe when you right-click a wire and select Probe, unless you already specified a custom or supplied probe for the data type. You can debug a custom probe similar to a VI. However, a probe cannot probe its own block diagram, nor the block diagram of any of its subVIs. When debugging probes, use the generic probe. Using Indicators to View Data You also can use an indicator to view the data that passes through a wire. For example, if you view numeric data, you can use a chart within the probe to view the data. Right-click a wire, select Custom ProbeControls from the shortcut menu, and select the indicator you want to use. You also can click the Select a Control icon on the Controls palette and select any custom control or type definition saved on the computer or in a shared directory on a server. LabVIEW treats type definitions as custom controls when you use them to view probed data. If the data type of the indicator you select does not match the data type of the wire you right-clicked, LabVIEW does not place the indicator on the wire.

LabVIEW Introduction Course Manual

3-14

ni.com

Lesson 3

Troubleshooting and Debugging VIs

Supplied Supplied probes are VIs that display comprehensive information about the data that passes through a wire. For example, the VI Refnum Probe returns information about the VI name, the VI path, and the hex value of the reference. You also can use a supplied probe to respond based on the data that flows through the wire. For example, use an Error probe on an error cluster to receive the status, code, source, and description of the error and specify if you want to set a conditional breakpoint if an error or warning occurs. The supplied probes appear at the top of the Custom Probe shortcut menu. Right-click a wire and select Custom Probe from the shortcut menu to select a supplied probe. Only probes that match the data type of the wire you right-click appear on the shortcut menu. Refer to the Using Supplied Probes VI in the labview\examples\ general\probes.llb for an example of using supplied probes. Custom Use the Create New Probe dialog box to create a probe based on an existing probe or to create a new probe. Right-click a wire and select Custom ProbeNew from the shortcut menu to display the Create New Probe dialog box. Create a probe when you want to have more control over how LabVIEW probes the data that flows through a wire. When you create a new probe, the data type of the probe matches the data type of the wire you right-clicked. If you want to edit the probe you created, you must open it from the directory where you saved it. After you select a probe from the Custom Probe shortcut menu, navigate to it using the Select a Control palette option, or create a new probe using the Create New Probe dialog box, that probe becomes the default probe for that data type, and LabVIEW loads that probe when you right-click a wire and select Probe from the shortcut menu. LabVIEW only loads probes that exactly match the data type of the wire you right-click. That is, a double precision floating-point numeric probe cannot probe a 32-bit unsigned integer wire even though LabVIEW can convert the data.
Note If you want a custom probe to be the default probe for a particular data type, save the probe in the user.lib\_probes\default directory. Do not save probes in the vi.lib\_probes directory because LabVIEW overwrites those files when you upgrade or reinstall.

National Instruments Corporation

3-15

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Breakpoints
Use the Breakpoint tool, shown as follows, to place a breakpoint on a VI, node, or wire on the block diagram and pause execution at that location.

When you set a breakpoint on a wire, execution pauses after data passes through the wire and the Pause button appears red. Place a breakpoint on the block diagram to pause execution after all nodes on the block diagram execute. The block diagram border appears red and flashes to reflect the placement of a breakpoint. When a VI pauses at a breakpoint, LabVIEW brings the block diagram to the front and uses a marquee to highlight the node or wire that contains the breakpoint. When you move the cursor over an existing breakpoint, the black area of the Breakpoint tool cursor appears white. When you reach a breakpoint during execution, the VI pauses and the Pause button appears red. You can take the following actions: Single-step through execution using the single-stepping buttons. Probe wires to check intermediate values. Change the values of front panel controls. Click the Pause button to continue running to the next breakpoint or until the VI finishes running.

Suspending Execution
Suspend execution of a subVI to edit values of controls and indicators, to control the number of times the subVI runs before returning to the caller, or to go back to the beginning of the execution of the subVI. You can cause all calls to a subVI to start with execution suspended, or you can suspend a specific call to a subVI. To suspend all calls to a subVI, open the subVI and select Operate Suspend when Called. The subVI automatically suspends when another VI calls it. If you select this menu item when single-stepping, the subVI does not suspend immediately. The subVI suspends when it is called. To suspend a specific subVI call, right-click the subVI node on the block diagram and select SubVI Node Setup from the shortcut menu. Place a checkmark in the Suspend when called checkbox to suspend execution only at that instance of the subVI.

LabVIEW Introduction Course Manual

3-16

ni.com

Lesson 3

Troubleshooting and Debugging VIs

The VI Hierarchy window, which you display by selecting ViewVI Hierarchy, indicates whether a VI is paused or suspended. An arrow glyph, shown as follows, indicates a VI that is running regularly or single-stepping.

A pause glyph, shown as follows, indicates a paused or suspended VI.

A green pause glyph, or a hollow glyph in black and white, indicates a VI that pauses when called. A red pause glyph, or a solid glyph in black and white, indicates a VI that is currently paused. An exclamation point glyph, shown as follows, indicates that the subVI is suspended.

A VI can be suspended and paused at the same time.

Determining the Current Instance of a SubVI

When you pause a subVI, the Call list pull-down menu on the toolbar lists the chain of callers from the top-level VI down to the subVI. This list is not the same list you see when you select BrowseThis VI's Callers, which lists all calling VIs regardless of whether they are currently running. Use the Call list menu to determine the current instance of the subVI if the block diagram contains more than one instance. When you select a VI from the Call list menu, its block diagram opens, and LabVIEW highlights the current instance of the subVI.

D. Undefined or Unexpected Data

Undefined data, which are NaN (not a number) or Inf (infinity), invalidate all subsequent operations. Floating-point operations return the following two symbolic values that indicate faulty computations or meaningless results:
NaN (not a number) represents a floating-point value that invalid

operations produce, such as taking the square root of a negative number.

Inf (infinity) represents a floating-point value that valid operations produce, such as dividing a number by zero.

LabVIEW does not check for overflow or underflow conditions on integer values. Overflow and underflow for floating-point numbers is in accordance with IEEE 754, Standard for Binary Floating-Point Arithmetic.

National Instruments Corporation

3-17

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Floating-point operations propagate NaN and Inf reliably. When you explicitly or implicitly convert NaN or Inf to integers or Boolean values, the values become meaningless. For example, dividing 1 by zero produces Inf. Converting Inf to a 16-bit integer produces the value 32,767, which appears to be a normal value. Before you convert data to integer data types, use the Probe tool to check intermediate floating-point values for validity. Check for NaN by wiring the Comparison function, Not A Number/Path/Refnum?, to the value you suspect is invalid. Do not rely on special values such as NaN, Inf, or empty arrays to determine if a VI produces undefined data. Instead, confirm that the VI produces defined data by making the VI report an error if it encounters a situation that is likely to produce undefined data. For example, if you create a VI that uses an incoming array to auto-index a For Loop, determine what you want the VI to do when the input array is empty. Either produce an output error code, substitute defined data for the value that the loop creates, or use a Case structure that does not execute the For Loop if the array is empty.

E. Error Checking and Error Handling

No matter how confident you are in the VI you create, you cannot predict every problem a user can encounter. Without a mechanism to check for errors, you know only that the VI does not work properly. Error checking tells you why and where errors occur.

Automatic Error Handling

Each error has a numeric code and a corresponding error message. By default, LabVIEW automatically handles any error when a VI runs by suspending execution, highlighting the subVI or function where the error occurred, and displaying an error dialog box. To disable automatic error handling for the current VI, select FileVI Properties and select Execution from the Category pull-down menu. To disable automatic error handling for any new, blank VIs you create, select ToolsOptions and select Block Diagram from the Category list. To disable automatic error handling for a subVI or function within a VI, wire its error out parameter to the error in parameter of another subVI or function or to an error out indicator.

LabVIEW Introduction Course Manual

3-18

ni.com

Lesson 3

Troubleshooting and Debugging VIs

Manual Error Handling

You can choose other error handling methods. For example, if an I/O VI on the block diagram times out, you might not want the entire application to stop and display an error dialog box. You also might want the VI to retry for a certain period of time. In LabVIEW, you can make these error handling decisions on the block diagram of the VI. Use the LabVIEW error handling VIs and functions on the Dialog & User Interface palette and the error in and error out parameters of most VIs and functions to manage errors. For example, if LabVIEW encounters an error, you can display the error message in different kinds of dialog boxes. Use error handling in conjunction with the debugging tools to find and manage errors. VIs and functions return errors in one of two wayswith numeric error codes or with an error cluster. Typically, functions use numeric error codes, and VIs use an error cluster, usually with error inputs and outputs. When you perform any kind of input and output (I/O), consider the possibility that errors might occur. Almost all I/O functions return error information. Include error checking in VIs, especially for I/O operations (file, serial, instrumentation, data acquisition, and communication), and provide a mechanism to handle errors appropriately. Use the LabVIEW error handling VIs, functions, and parameters to manage errors. For example, if LabVIEW encounters an error, you can display the error message in a dialog box. Or you can fix the error programmatically then erase the error by wiring the error out output of the subVI or function to the error in input of the Clear Errors VI. Use error handling in conjunction with the debugging tools to find and manage errors. National Instruments strongly recommends using error handling.

Error Clusters
Use the error cluster controls and indicators to create error inputs and outputs in subVIs. The error in and error out clusters include the following components of information: status is a Boolean value that reports TRUE if an error occurred. code is a 32-bit signed integer that identifies the error numerically. A nonzero error code coupled with a status of FALSE signals a warning rather than a error. source is a string that identifies where the error occurred.

National Instruments Corporation

3-19

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Error handling in LabVIEW follows the dataflow model. Just as data values flow through a VI, so can error information. Wire the error information from the beginning of the VI to the end. Include an error handler VI at the end of the VI to determine if the VI ran without errors. Use the error in and error out clusters in each VI you use or build to pass the error information through the VI. As the VI runs, LabVIEW tests for errors at each execution node. If LabVIEW does not find any errors, the node executes normally. If LabVIEW detects an error, the node passes the error to the next node without executing that part of the code. The next node does the same thing, and so on. At the end of the execution flow, LabVIEW reports the error.

Explain Error
When an error occurs, right-click within the cluster border and select Explain Error from the shortcut menu to open the Explain Error dialog box. The Explain Error dialog box contains information about the error. The shortcut menu includes an Explain Warning option if the VI contains warnings but no errors. You also can access the Explain Error dialog box from the HelpExplain Error menu. VIs and functions return errors in one of two wayswith numeric error codes or with an error cluster. Typically, functions use numeric error codes, and VIs use an error cluster, usually with error inputs and outputs.

LabVIEW Introduction Course Manual

3-20

ni.com

Lesson 3

Troubleshooting and Debugging VIs

Exercise 3-2
Goal

Concept: Debugging
Use the debugging tools built into LabVIEW.

Description
Complete the following steps to load a broken VI and correct the errors. Use single-stepping and execution highlighting to step through the VI. 1. Open and examine the Debug Exercise (Main) VI. Select FileOpen. Open Debug Exercise (Main).vi in the <Exercises>\ LabVIEW Basics I\Debugging directory. The following front panel appears.

Figure 3-6. Debug Exercise (Main).vi Front Panel

Notice the Run button on the toolbar appears broken, indicating that the VI is broken and cannot run.

National Instruments Corporation

3-21

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

2. Display and examine the block diagram of Debug Exercise (Main) VI. Select WindowShow Block Diagram to display the block diagram shown in Figure 3-7.

Figure 3-7. Debug Exercise (Main).vi Block Diagram

The Random Number (0-1) function produces a random number between 0 and 1. The Multiply function multiplies the random number by 10.0. The numeric constant is the number multiplied with the random number. The Debug Exercise (Sub) VI, located in the <Exercises>\ LabVIEW Basics I\Debugging\Supporting Files directory, adds 100.0 and calculates the square root of the value.

3. Find and fix each error. Click the broken Run button to display the Error list window, which lists all the errors. Select an error description in the Error list window. The Details section describes the error and in some cases recommends how to correct the error. Click the Help button to display a topic in the LabVIEW Help that describes the error in detail and includes step-by-step instructions for correcting the error.

LabVIEW Introduction Course Manual

3-22

ni.com

Lesson 3

Troubleshooting and Debugging VIs

Click the Show Error button or double-click the error description to highlight the area on the block diagram that contains the error. Use the Error list window to fix each error. 4. Select FileSave to save the VI. 5. Display the front panel by clicking it or by selecting WindowShow Front Panel. 6. Click the Run button. 7. Select WindowShow Block Diagram to display the block diagram. 8. Animate the flow of data through the block diagram. Click the Highlight Execution button on the toolbar to enable execution highlighting. Click the Step Into button to start single-stepping. Execution highlighting shows the flow of data on the block diagram from one node to another using bubbles that move along the wires. Nodes blink to indicate they are ready to execute. Click the Step Over button after each node to step through the entire block diagram. Each time you click the Step Over button, the current node executes and pauses at the next node. Data appear on the front panel as you step through the VI. The VI generates a random number and multiplies it by 10.0. The subVI adds 100.0 and calculates the square root of the result. When a blinking border surrounds the entire block diagram, click the Step Out button to stop single-stepping through the Debug Exercise (Main) VI. 9. Single-step through the VI and its subVI. Click the Step Into button to start single-stepping. When the Debug Exercise (Sub) VI blinks, click the Step Into button. Notice the Run button on the subVI. Display the Debug Exercise (Main) VI block diagram by clicking it. A green glyph appears on the subVI icon on the Debug Exercise (Main) VI block diagram, indicating that the subVI is running. Display the Debug Exercise (Sub) VI block diagram by clicking it.

National Instruments Corporation

3-23

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Click the Step Out button twice to finish single-stepping through the subVI block diagram. The Debug Exercise (Main) VI block diagram is active. Click the Step Out button to stop single-stepping. 10. Use a probe to check intermediate values on a wire as a VI runs. Use the Probe tool to click any wire. The Probe window appears. LabVIEW increments the numbers in the Probe window automatically and displays the corresponding number in a glyph on the wire you clicked. Single-step through the VI again. The Probe window displays data passed along the wire. 11. Place breakpoints on the block diagram to pause execution at that location. Use the Breakpoint tool to click nodes or wires. Place a breakpoint on the block diagram to pause execution after all nodes on the block diagram execute. Click the Run button to run the VI. When you reach a breakpoint during execution, the VI pauses and the Pause button on the toolbar appears red. Click the Continue button to continue running to the next breakpoint or until the VI finishes running. Use the Breakpoint tool to click the breakpoints you set and remove them. 12. Click the Highlight Execution button to disable execution highlighting. 13. Select FileClose to close the VI and all open windows.

End of Exercise 3-2

LabVIEW Introduction Course Manual

3-24

ni.com

Lesson 3

Troubleshooting and Debugging VIs

Self Review: Quiz

1. How do you disable automatic error handling? a. Select OperateDisable Error Handling. b. Enable execution highlighting. c. Wire the error out cluster of a subVI to the error in cluster of another subVI. d. Place a checkmark in the Show Warnings checkbox of the Error list window. 2. Which of the following are the contents of the error cluster? (multiple answers) a. Status: Boolean b. Error: String c. Code: 32-bit integer d. Source: String

National Instruments Corporation

3-25

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Self Review: Quiz Answers

1. How do you disable automatic error handling? a. Select OperateDisable Error Handling. b. Enable execution highlighting. c. Wire the error out cluster of a subVI to the error in cluster of another subVI. d. Place a checkmark in the Show Warnings checkbox of the Error list window. 2. Which of the following are the contents of the error cluster? (multiple answers) a. Status: Boolean b. Error: String c. Code: 32-bit integer d. Source: String

National Instruments Corporation

3-27

LabVIEW Introduction Course Manual

Lesson 3

Troubleshooting and Debugging VIs

Notes

LabVIEW Introduction Course Manual

3-28

ni.com

Implementing a VI

This lesson teaches you how to implement code in LabVIEW. These skills include designing a user interface, choosing a data type, documenting your code, using looping structures such as While Loops and For Loops, adding software timing to your code, displaying your data as a plot, and making decisions in your code using a Case structure.

Topics
A. Designing Front Panel Windows B. LabVIEW Data Types C. Documenting Code D. While Loops E. For Loops F. Timing a VI G. Iterative Data Transfer H. Plotting Data I. Case Structures J. Formula Nodes

National Instruments Corporation

4-1

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

A. Designing Front Panel Windows

In the design phase of the software development method, you identify the inputs and outputs of the problem. This identification leads directly to the design of the front panel window. You can retrieve the inputs of the problem using the following methods: acquiring from a device such as a data acquisition device or a multimeter. reading directly from a file. manipulating controls.

You can display the outputs of the problem with indicators, such as graphs, charts, or LEDs, or log the outputs to a file. You also can output data to a device using signal generation. Lessons about data acquisition, signal generation, and file logging appear later in this course.

Designing Controls and Indicators

When choosing controls and indicators, make sure that they are appropriate for the task you want to perform. For example, when you want to determine the frequency of a sine wave, choose a dial control, or when you want to display temperature, choose a thermometer indicator.

Labels and Captions

Make sure to label controls and indicators clearly. These labels help users identify the purpose of each control and indicator. Also, clear labeling helps you document your code on the block diagram. Control and indicator labels correspond to the names of terminals on the block diagram. Captions help you describe a front panel control. Captions do not appear on the block diagram. Using captions allows you to document the user interface without cluttering the block diagram with additional text. For example, in the Weather Station, you must provide an upper boundary for the temperature level. If the temperature rises above this level, the Weather Station indicates a heatstroke warning. You could call this control Upper Temperature Limit (Celsius). However, this label would occupy unnecessary space on the block diagram. Instead, use a caption for the control Upper Temperature Limit (Celsius) and use the label to create a shorter description for the block diagram, such as Upper Temp.

LabVIEW Introduction Course Manual

4-2

ni.com

Lesson 4

Implementing a VI

Control and Indicator Options

You can set default values for controls. Figure 4-2 shows a default value of 35 C. By setting a default value, you can assume a reasonable value for a VI if the user does not set another value during run-time. To set the default value, complete the following steps: 1. Enter the desired value. 2. Right-click the control and select Data OperationsMake Current Value Default from the shortcut menu. You also can hide and view items on controls and indicators. For example, in Figure 4-1, you can see both the caption and the label. However, you only need to see the caption. To hide the label, right-click the control and select Visible ItemsLabel as shown in Figure 4-2.

2 1

Front Panel Window

Block Diagram

Figure 4-1. Setting Default Values

Before Hiding the Label

After Hiding the Label

Figure 4-2. Hiding a Front Panel Label

National Instruments Corporation

4-3

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Using Color
Proper use of color can improve the appearance and functionality of your user interface. Using too many colors, however, can result in color clashes that cause the user interface to look too busy and distracting. LabVIEW provides a color picker that can aid in selecting appropriate colors. Select the Coloring tool and right-click an object or workspace to display the color picker. The top of the color picker contains a grayscale spectrum and a box you can use to create transparent objects. The second spectrum contains muted colors that are well suited to backgrounds and front panel objects. The third spectrum contains colors that are well suited for highlights. Moving your cursor vertically from the background colors to the highlight colors helps you select appropriate highlight colors for a specific background color. The following tips are helpful for color matching: Use the default LabVIEW colors. LabVIEW substitutes colors similarly to how it substitutes fonts. If one of the colors of the VI is unavailable, LabVIEW substitutes the closest match. You also can use system colors to adapt the appearance of a front panel window to the system colors of any computer that runs the VI. Start with a gray scheme. Select one or two shades of gray and choose highlight colors that contrast well against the background. Add highlight colors sparinglyon plots, abort buttons, and perhaps the slider thumbsfor important settings. Small objects need brighter colors and more contrast than larger objects. Use differences in contrast more often that differences in color. Color-blind users find it difficult to discern objects when differences are in color rather than contrast. Use spacing and alignment to group objects instead of grouping by matching colors. Good places to learn about color are stand-alone hardware instrument panels, maps, and magazines. Choose objects from the System category of the Controls palette if you want your front panel controls to use the system colors.

Spacing and Alignment

White space and alignment are probably the most important techniques for grouping and separation. The more items that your eye can find on a line, the cleaner and more cohesive the organization seems. When items are on a line, the eye follows the line from left to right or top to bottom. This is related to the script direction. Although some cultures view items right to left, almost all follow top to bottom.

LabVIEW Introduction Course Manual

4-4

ni.com

Lesson 4

Implementing a VI

When you design the front panel, consider how users interact logically with the VI and group controls and indicators. If several controls are related, add a decorative border around them or put them in a cluster. Centered items are less orderly than items aligned to the left or right. A band of white space acts as a very strong means of alignment. Centered items typically have ragged edges and the order is not as easily noticed. Do not place front panel objects too closely together. Leave some blank space between objects to make the front panel easier to read. Blank space also prevents users from accidentally clicking the wrong control or button. Left-justify menus and right-justify related shortcuts as shown in Figure 4-3 example 1, the LabVIEW File menu. Locating items in the center-justified menu as shown in the same example on the right is more difficult. Notice how the dividing lines between menu sections in example 1 help you find the items quickly and strengthen the relationship between the items in the sections.

Good Menu

Bad Menu

Figure 4-3. Good and Bad Menu Examples

National Instruments Corporation

4-5

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Avoid placing objects on top of other objects. Even partially covering a control or indicator with a label or other object slows down screen updates and can make the control or indicator flicker.

Text and Fonts

Text is easier to read and information is more easily understood when displayed in an orderly way. Use the default LabVIEW fonts. For instance, LabVIEW defines its built-in fonts as the default system font. When you move VIs between platforms, LabVIEW automatically updates its built-in fonts so that they match the default system font of the current platform. Additionally, if you attempt to display a VI that uses a font that is unavailable, LabVIEW substitutes the closest match. For example, if you try to view a VI that uses the Arial font on a computer which does not have the Arial font, LabVIEW substitutes the Arial font with a similar, installed font. Using too many font styles can make your front panel window look busy and disorganized. Instead, use two or three different sizes of the same font. Serifs help people to recognize whole words from a distance. If you are using more than one size of a font, make sure the sizes are noticeably different. If not, it may look like a mistake. Similarly, if you use two different fonts, make sure they are distinct. Design your user interface with larger fonts and more contrast for industrial operator stations. Glare from lighting or the need to read information from a distance can make normal fonts difficult to read. Also, remember that touch screens generally require larger fonts and more spacing between selection items. If fonts do not exist on a target machine, substituted fonts can cause the user interface to appear skewed.
Note

User Interface Tips and Tools

Some of the built-in LabVIEW tools for making user-friendly front panel windows include system controls, tab controls, decorations, menus, and automatic resizing of front panel objects.

System Controls
A common user interface technique is to display dialog boxes at appropriate times to interact with the user. You can make a VI behave like a dialog box by selecting FileVI Properties, selecting the Window Appearance category, and selecting the Dialog option. Use the system controls and indicators located on the System palette in dialog boxes you create.

LabVIEW Introduction Course Manual

4-6

ni.com

Lesson 4

Implementing a VI

Because the system controls change appearance depending on which platform you run the VI, the appearance of controls in VIs you create is compatible on all LabVIEW platforms. When you run the VI on a different platform, the system controls adapt their color and appearance to match the standard dialog box controls for that platform. System controls typically ignore all colors except transparent. If you are integrating a graph or non-system control into the front panel windows, match them by hiding some borders or selecting colors similar to the system colors.

Tab Controls
Physical instruments usually have good user interfaces. Borrow heavily from their design principles, but use smaller or more efficient controls, such as ring controls or tab controls, where appropriate. Use tab controls to overlap front panel controls and indicators in a smaller area. To add additional pages to a tab control, right-click a tab and select Add Page Before or Add Page After from the shortcut menu. Relabel the tabs with the Labeling tool, and place front panel objects on the appropriate pages. The terminals for these objects are available on the block diagram, as are terminals for any other front panel object (except Decorations). You can wire the enumerated control terminal of the tab control to the selector of a Case structure to produce cleaner block diagrams. With this method you associate each page of the tab control with a subdiagram in the Case structure. Place the control and indicator terminals from each page of the tab controlas well as the block diagram nodes and wires associated with those terminalsinto the subdiagrams of the Case structure.

Decorations
Use the decorations located on the Decorations palette to group or separate objects on a front panel with boxes, lines, or arrows. The objects on the Decorations palette do not display data.

Menus
Use custom menus to present front panel functionality in an orderly way and in a relatively small space. Using small amounts of space leaves room on the front panel for critical controls and indicators, items for beginners, items needed for productivity, and items that do not fit well into menus. You also can create keyboard shortcuts for menu items. To create a run-time shortcut menu for front panel objects, right-click the front panel object and select AdvancedRun-Time Shortcut MenuEdit.

National Instruments Corporation

4-7

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

To create a custom run-time menu for your VI, select EditRun-Time Menu.

Automatic Resizing of Front Panel Objects

Use the VI PropertiesWindow Size options to set the minimum size of a window, maintain the window proportion during screen changes, and set front panel objects to resize in two different modes. When you design a VI, consider whether the front panel can display on computers with different screen resolutions. Select FileVI Properties, select Window Size in the Category pull-down menu, and place a checkmark in the Maintain proportions of window for different monitor resolutions checkbox to maintain front panel window proportions relative to the screen resolution.

LabVIEW Introduction Course Manual

4-8

ni.com

Lesson 4

Implementing a VI

B. LabVIEW Data Types

Many different data types exist for data. You already learned about numeric, Boolean, and string data types in Lesson 2, Navigating LabVIEW. Other data types include the enumerated data type, dynamic data, and others. Even within numeric data types, there are different data types, such as whole numbers or fractional numbers.

Terminals
The block diagram terminals visually communicate to the user some information about the data type they represent. For example, in Figure 4-4, Height (cm) is a double-precision, floating-point numeric. This is indicated by the color of the terminal, orange, and by the text shown on the terminal, DBL.

Figure 4-4. Terminal Data Type Example

Numeric Data Types

The numeric data type represents numbers of various types. To change the representation type of a number, right-click the control, indicator, or constant, and select Representation, as shown in Figure 4-5.

National Instruments Corporation

4-9

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Figure 4-5. Numeric Representation

When you wire two or more numeric inputs of different representations to a function, the function usually returns the data in the larger, or wider, representation. The functions coerce the smaller representations to the widest representation before execution and LabVIEW places a coercion dot on the terminal where the conversion takes place. The numeric data type includes the following subcategories of representationfloating-point numbers, signed integers, unsigned integers, and complex numbers.

Floating-Point Numbers
Floating-point numbers represent fractional numbers. In LabVIEW, floating-point numbers are represented with the color orange. Single-precision (SGL)Single-precision, floating-point numbers have 32-bit IEEE single-precision format. Use single-precision, floating-point numbers to save memory and avoid overflowing the range of the numbers. Double-precision (DBL)Double-precision, floating-point numbers have 64-bit IEEE double-precision format. Double-precision is the default format

LabVIEW Introduction Course Manual

4-10

ni.com

Lesson 4

Implementing a VI

for numeric objects. For most situations, use double-precision, floating-point numbers. Extended-precision (EXT)In memory, the size and precision of extended-precision numbers vary depending on the platform. In Windows, they have 80-bit IEEE extended-precision format.

Integers
Integers represent whole numbers. Signed integers can be positive or negative. Use the unsigned integer data types when you know the integer is always positive. In LabVIEW, integers are represented with the color blue. When LabVIEW converts floating-point numbers to integers, the VI rounds to the nearest even integer. For example, LabVIEW rounds 2.5 to 2 and rounds 3.5 to 4. Byte (I8)Byte integer numbers have 8 bits of storage. Word (I16)Word integer numbers have 16 bits of storage. Long (I32)Long integer numbers have 32 bits of storage. In most cases, it is best to use a 32-bit integer. Quad (I64)Quad integer numbers have 64 bits of storage.

Complex Numbers
Complex numbers are represented by two values linked together in memoryone representing the real part and one representing the imaginary part. In LabVIEW, because complex numbers are a type of floating-point number, complex numbers are also represented with the color orange. Complex Single (CSG)Complex single-precision, floating-point numbers consist of real and imaginary values in 32-bit IEEE single-precision format. Complex Double (CDB)Complex double-precision, floating-point numbers consist of real and imaginary values in 64-bit IEEE double-precision format. Complex Extended (CXT)Complex extended-precision, floating-point numbers consist of real and imaginary values in IEEE extended-precision format. In memory, the size and precision of extended-precision numbers vary depending on the platform. In Windows, they have 80-bit IEEE extended-precision format.

National Instruments Corporation

4-11

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Boolean Values
LabVIEW stores Boolean data as 8-bit values. If the 8-bit value is zero, the Boolean value is FALSE. Any nonzero value represents TRUE. In LabVIEW, the color green represents Boolean data. Boolean values also have a mechanical action associated with them. The two major actions are latch and switch. Latch action is similar to a doorbell, whereas switch action is similar to a light switch. You can also define when the switch or latch occurswhen pressed, when released, or until released. To learn more about mechanical action, experiment with the Mechanical Action of Booleans VI in the NI Example Finder.

Figure 4-6. Boolean Mechanical Action

Strings
A string is a sequence of displayable or non-displayable ASCII characters. Strings provide a platform-independent format for information and data. Some of the more common applications of strings include the following: Creating simple text messages. Controlling instruments by sending text commands to the instrument and returning data values in the form of either ASCII or binary strings which you then convert to numeric values.

LabVIEW Introduction Course Manual

4-12

ni.com

Lesson 4

Implementing a VI

Storing numeric data to disk. To store numeric data in an ASCII file, you must first convert numeric data to strings before writing the data to a disk file. Instructing or prompting the user with dialog boxes.

On the front panel, strings appear as tables, text entry boxes, and labels. LabVIEW includes built-in VIs and functions you can use to manipulate strings, including formatting strings, parsing strings, and other editing. Refer to the ASCII Codes topic for more information about ASCII codes and conversion functions. On the front panel window, strings appear as tables, text entry boxes, and labels. LabVIEW includes built-in VIs and functions you can use to manipulate strings, including formatting strings, parsing strings, and other editing. In LabVIEW, strings are represented with the color pink. Right-click a string control or indicator on the front panel to select from the display types shown in the following table. The table also shows an example message in each display type. Display Type Normal Display Description Displays printable characters using the font of the control. Non-displayable characters generally appear as boxes. Displays backslash codes for all non-displayable characters. Displays an asterisk (*) for each character including spaces. Displays the ASCII value of each character in hex instead of the character itself. Message
There are four display types.\ is a backslash.

\ Codes Display Password Display

There\sare\sfour\sdisplay\st ypes.\n\\\sis\sa\sbackslash. **************************** *****************

Hex Display

5468 7572 7970 2062

6572 2064 6573 6163

6520 6172 6520 666F 6973 706C 6179 2074 2E0A 5C20 6973 2061 6B73 6C61 7368 2E

LabVIEW stores strings as a pointer to a structure that contains a 4-byte length value followed by a 1D array of byte integers (8-bit characters).

National Instruments Corporation

4-13

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Enums
An enum (enumerated control, constant or indicator) is a combination of data types. An enum represents a pair of values, a string and a numeric, where the enum can be one of a list of values. For example, if you created an enum type called Month, the possible value pairs for a Month variable are January-0, February-1, and so on through December-11. Figure 4-7 shows an example of these data pairs in the Properties dialog box for an enumerated control.

Figure 4-7. Properties for the Month Enumerated Control

Enums are useful because it is easier to manipulate numbers on the block diagram than strings. Figure 4-8 shows the Month enumerated control, the selection of a data pair in the enumerated control, and the corresponding block diagram terminal.

LabVIEW Introduction Course Manual

4-14

ni.com

Lesson 4

Implementing a VI

Front Panel Control

Selecting an Item

Block Diagram Terminal

Figure 4-8. Month Enumerated Control

Dynamic
The dynamic data type stores the information generated or acquired by an Express VI. The dynamic data type appears as a dark blue terminal, shown at left. Most Express VIs accept and/or return the dynamic data type. You can wire the dynamic data type to any indicator or input that accepts numeric, waveform, or Boolean data. Wire the dynamic data type to an indicator that can best present the data. Indicators include graphs, charts, or numeric indicators. Most other VIs and functions in LabVIEW do not accept the dynamic data type. To use a built-in VI or function to analyze or process the data the dynamic data type includes, you must convert the dynamic data type. Use the Convert from Dynamic Data Express VI to convert the dynamic data type to numeric, Boolean, waveform, and array data types for use with other VIs and functions. When you place the Convert from Dynamic Data Express VI on the block diagram, the Configure Convert from Dynamic Data dialog box appears. The Configure Convert from Dynamic Data dialog box displays options that let you specify how you want to format the data that the Convert from Dynamic Data Express VI returns. When you wire a dynamic data type to an array indicator, LabVIEW automatically adds the Convert from Dynamic Data Express VI to the block diagram. Double-click the Convert from Dynamic Data Express VI to open the Configure Convert from Dynamic Data dialog box to control how the data appears in the array.

National Instruments Corporation

4-15

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

C. Documenting Code
Professional developers who maintain and modify VIs know the value of good documentation. Document the block diagram well to ease future modification of the code. In addition, document the front panel window well to explain the purpose of the VI and the front panel objects. Use tip strips, descriptions, VI Properties, and good design to document front panel windows.

Tip Strips and Descriptions

Tip strips are brief descriptions that appear when you move the cursor over a control or indicator while a VI runs. For example, you might add a tip strip to indicate that a temperature is in degrees Celsius or explain how an input works in an algorithm. Descriptions provide additional information about specific controls and indicators. Descriptions appear in the Context Help window when you move the cursor over the object. To add tip strips and descriptions to controls, right-click the control or indicator and select Description and Tip from the shortcut menu.

VI Properties
Use the Documentation component of the VI Properties dialog box to create VI descriptions and to link from VIs to HTML files or to compiled help files. To display VI Properties right-click the VI icon on the front panel or block diagram and select VI Properties from the shortcut menu or select FileVI Properties. Then select Documentation from the Categories drop-down menu. You cannot access this dialog box while a VI runs. This page includes the following components: VI descriptionContains the text that appears in the Context Help window if you move the cursor over the VI icon. Use <B> and </B> tags around any text in the description you want to format as bold. You also can use the VI Description property to edit the VI description programmatically. Help tagContains the HTML filename or index keyword of the topic you want to link to in a compiled help file. You also can use the Help:Document Tag property to set the help tag programmatically. Help pathContains the path to the HTML file or to the compiled help file you want to link to from the Context Help window. If this field is empty, the Detailed help link does not appear in the Context Help window, and the Detailed help button is dimmed. BrowseDisplays a file dialog box to use to navigate to an HTML file or to a compiled help file to use as the Help path.

LabVIEW Introduction Course Manual

4-16

ni.com

Lesson 4

Implementing a VI

Naming Controls and Indicators

Giving controls and indicators logical and descriptive names adds usability to front panels. For example, if you name a control Temperature, a user may not know which units to use. However, naming a control Temperature C adds more information to the front panel. You now know to enter temperatures in metric units.

Graphical Programming
While the graphical nature of LabVIEW aids in self-documentation of block diagrams, extra comments are helpful when modifying your VIs in the future. There are two types of block diagram commentscomments that describe the function or operation of algorithms and comments that explain the purpose of data that passes through wires. Both types of comments are shown in the following block diagram. You can insert standard labels with the Labeling tool, or by inserting a free label from the Functions ProgrammingStructuresDecorations subpalette. By default, free labels have a yellow background color.

Figure 4-9. Documenting a Block Diagram

Use the following guidelines for commenting your VIs: Use comments on the block diagram to explain what the code is doing. While LabVIEW code can be self-documenting because it is graphical, use free labels to describe how the block diagram functions. Do not show labels on function and subVI calls because they tend to be large and unwieldy. A developer looking at the block diagram can find the name of a function or subVI by using the Context Help window. Use small free labels with white backgrounds to label long wires to identify their use. Labeling wires is useful for wires coming from shift registers and for long wires that span the entire block diagram. Refer to the Case Structures section of this lesson for more information about shift registers.

National Instruments Corporation

4-17

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Label structures to specify the main functionality of the structure. Label constants to specify the nature of the constant. Use free labels to document algorithms that you use on the block diagrams. If you use an algorithm from a book or other reference, provide the reference information.

LabVIEW Introduction Course Manual

4-18

ni.com

Lesson 4

Implementing a VI

Exercise 4-1
Goal

Determine Warnings VI
Create and document a simple VI.

Scenario
You must create a portion of a larger project. The lead developer gives you the inputs of the VI, the algorithm, and the expected outputs. Create and document a VI based on the given design.

Design Inputs and Outputs

Type Numeric control Numeric control Numeric control String indicator Name
Current Temp

Properties Double-precision, floating-point Double-precision, floating-point Double-precision, floating-point Three potential values: Heatstroke Warning, No Warning, and Freeze Warning

Max Temp

Min Temp

Warning Text

Round LED indicator

Warning?

National Instruments Corporation

4-19

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Flowchart

Current Temp >=Max Temp?

No

Yes

Warning Text = Heatstroke Warning

Warning Text = No Warning

Current Temp <= Min Temp?

No

Yes

Warning Text = Freeze Warning

Pass current value of Warning Text

Warning Text = No Warning?

No

Yes

Warning ? = False

Warning ? = True

Figure 4-10. Determine Warnings VI Flowchart

LabVIEW Introduction Course Manual

4-20

ni.com

Lesson 4

Implementing a VI

Implementation
Follow the instructions given below to create a front panel similar to Figure 4-11. This front panel retrieves from the user the current temperature, the maximum temperature, and the minimum temperature, and displays to the user the warning string and the warning Boolean LED. This VI is part of the temperature weather station project studied throughout the course. 1. Open a blank VI and create the following front panel.

Figure 4-11. Determine Warnings VI Front Panel

2. Save the new VI. Select FileSave. Save the VI as Determine Warnings.vi in the <Exercises>\ LabVIEW Basics I\Determine Warnings directory. 3. Create a numeric control for the current temperature. Add a numeric control to the front panel window. Change the label of the numeric control to Current Temp. Right-click the control, select Representation, and confirm that the representation type is set to double precision. This subVI could be used for Fahrenheit, Kelvin, or any other temperature scale, as long as all inputs use the same scale. Therefore, it is not necessary to add scale units to the labels.
Tip

National Instruments Corporation

4-21

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

4. Create a numeric control for the maximum temperature. Hold down the <Ctrl> key and click and drag the Current Temp numeric control to create a copy of the control. Change the label text of the new numeric control to Max Temp. 5. Create a numeric control for the minimum temperature. Hold down the <Ctrl> key and click and drag the Max Temp numeric control to create a copy of the control. Change the label text of the new numeric control to Min Temp. 6. Create a string indicator for the warning text. Add a string indicator to the front panel window. Change the label text of the string indicator to Warning Text. 7. Create a Round LED or other Boolean indicator for the warning Boolean. Add a Round LED to the front panel window. Change the label text of the Boolean indicator to Warning?. 8. Switch to the block diagram.
Tip If you do not want to view terminals as icons on the block diagram, select Tools Options, then select Block Diagram from the Category list. Remove the checkmark from the Place front panel terminals as icons item.

Follow the instructions given below to create a block diagram similar to Figure 4-12.

LabVIEW Introduction Course Manual

4-22

ni.com

Lesson 4

Implementing a VI

Figure 4-12. Determine Warnings VI Block Diagram

9. Compare Current Temp and Max Temp. Add a Greater Or Equal? function to the block diagram. Wire the Current Temp control to the x input of the Greater Or Equal? function. Wire the Max Temp control to the y input of the Greater Or Equal? function. 10. Compare Current Temp and Min Temp. Add a Less Or Equal? function to the block diagram. Wire the Current Temp control to the x input of the Less Or Equal? function. Wire the Min Temp control to the y input of the Less Or Equal? function. 11. If the Current Temp is equal to or greater than the Max Temp, generate a Heatstroke Warning string, otherwise generate a No Warning string. Add the Select function to the block diagram to the right of the Greater Or Equal? function. Wire the output of the Greater Or Equal? function to the s input of the Select function. Add a string constant to the block diagram to the upper left of the Select function.

National Instruments Corporation

4-23

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Enter Heatstroke Warning in the string constant. Wire the Heatstroke Warning string to the t input of the Select function. Hold down the <Ctrl> key and click and drag the Heatstroke Warning string constant to the lower left of the Select function to create a copy of the constant. Enter No Warning in the second string constant. Wire the No Warning string to the f input of the Select function. 12. If the Current Temp is equal to or less than the Min Temp, generate a Freeze Warning string, otherwise use the string generated in step 11. Create a copy of the Select function and place it to the right of the Less Or Equal? function. Wire the output of the Less Or Equal? function to the s input of the Select function. Create a copy of the string constant and place it to the upper left of the Select function. Enter Freeze Warning in the string constant. Wire the Freeze Warning string to the t input of the Select function. Wire the output of the previous Select function to the f input of the new Select function. 13. Display the generated text. Wire the output of the second Select function to the Warning Text indicator. 14. Generate the Warning? Boolean control by determining if the value of Warning Text is equal to No Warning. Add a Not Equal? function to the left of the Warning? Boolean control. Wire the output of the second Select function to the x input of the Not Equal? function.

LabVIEW Introduction Course Manual

4-24

ni.com

Lesson 4

Implementing a VI

Wire the No Warning string constant to the y input of the Not Equal? function. Wire the output of the Not Equal? function to the Warning? control. 15. Document the code using the following suggestions on the front panel. Create tip strips for each control and indicator stating the purpose and units of the object. To access tip strips, right-click an object, and select Description and Tip. Document the VI Properties, giving a general description of the VI, a list of inputs and outputs, your name, and the date the VI was created. To access the VI Properties dialog box, select File VI Properties. Document the block diagram algorithm with a free label. 16. Save the VI.

Test
1. Test the VI by entering a value for Current Temp, Max Temp, and Min Temp, and running the VI for each set. Table 4-1 shows the expected Warning Text string and Warning? Boolean value for each set of input values.
Table 4-1. Testing Values for Determine Warnings VI

Current Temp 30 25 10 30 30 30

Max Temp 10 10 10

Min Temp

Warning Text
Heatstroke Warning No Warning Freeze Warning

Warning? True False True

What happens if you input a Max Temp value that is less than the Min Temp? What would you expect to happen? You learn to handle issues like this one in Exercise 4-6. 2. Save and close the VI.

End of Exercise 4-1

National Instruments Corporation

4-25

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

D. While Loops
Similar to a Do Loop or a Repeat-Until Loop in text-based programming languages, a While Loop, shown in Figure 4-13 , executes a subdiagram until a condition occurs. The following illustration shows a While Loop in LabVIEW, a flowchart equivalent of the While Loop functionality, and a pseudo code example of the functionality of the While Loop.

Code No Code Condition met? Yes End 1 2 3 Repeat (code); Until Condition met; End;

LabVIEW While Loop

Flowchart

Pseudo Code

Figure 4-13. While Loop

The While Loop is located on the Structures palette. Select the While Loop from the palette then use the cursor to drag a selection rectangle around the section of the block diagram you want to repeat. When you release the mouse button, a While Loop boundary encloses the section you selected. Add block diagram objects to the While Loop by dragging and dropping them inside the While Loop.
Tip

The While Loop always executes at least once. The While Loop executes the subdiagram until the conditional terminal, an input terminal, receives a specific Boolean value. The conditional terminal in a While Loop behaves the same as in a For Loop with a conditional terminal. However, because the For Loop also includes a set iteration count, it does not run infinitely if the condition never occurs. The While Loop does not include a set iteration count and runs infinitely if the condition never occurs.

LabVIEW Introduction Course Manual

4-26

ni.com

Lesson 4

Implementing a VI

If a conditional terminal is Stop if True, you place the terminal of a Boolean control outside a While Loop, and the control is FALSE when the loop starts, you cause an infinite loop, as shown in the following example. You also cause an infinite loop if the conditional terminal is Continue if True and the control outside the loop is set to TRUE.

Changing the value of the control does not stop the infinite loop because the value is only read once, before the loop starts. To stop an infinite loop, you must abort the VI by clicking the Abort Execution button on the toolbar. You also can perform basic error handling using the conditional terminal of a While Loop. When you wire an error cluster to the conditional terminal, only the TRUE or FALSE value of the status parameter of the error cluster passes to the terminal. Also, the Stop if True and Continue if True shortcut menu items change to Stop if Error and Continue while Error. The iteration terminal, shown as follows, is an output terminal that contains the number of completed iterations.

The iteration count always starts at zero. During the first iteration, the iteration terminal returns 0. In the following block diagram, the While Loop executes until the Random Number function output is greater than or equal to 10.00 and the Enable control is True. The And function returns True only if both inputs are True. Otherwise, it returns False.

National Instruments Corporation

4-27

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

In the following example, there is an increased probability of an infinite loop. Generally, the desired behavior is to have one condition met to stop the loop, rather than requiring both conditions to be met.

Figure 4-14. Possible Infinite Loop

Structure Tunnels
Tunnels feed data into and out of structures. The tunnel appears as a solid block on the border of the While Loop. The block is the color of the data type wired to the tunnel. Data pass out of a loop after the loop terminates. When a tunnel passes data into a loop, the loop executes only after data arrive at the tunnel. In the following block diagram, the iteration terminal is connected to a tunnel. The value in the tunnel does not get passed to the Iterations indicator until the While Loop finishes executing.

Figure 4-15. While Loop Tunnel

Only the last value of the iteration terminal displays in the Iterations indicator.

LabVIEW Introduction Course Manual

4-28

ni.com

Lesson 4

Implementing a VI

Using While Loops for Error Handling

You can wire an error cluster to the conditional terminal of a While Loop or a For Loop with a conditional terminal to stop the iteration of the loop. If you wire the error cluster to the conditional terminal, only the TRUE or FALSE value of the status parameter of the error cluster passes to the terminal. If an error occurs, the loop stops. In a For Loop with a conditional terminal, you also must wire a value to the count terminal or auto-index an input array to set a maximum number of iterations. The For Loop executes until an error occurs or until the number of set iterations completes. If you wire an error cluster to the conditional terminal, the shortcut menu items Stop if True and Continue if True change to Stop on Error and Continue while Error. In Figure 4-16, the error cluster and a stop button are used together to determine when to stop the loop. This is the recommended method for stopping most loops.

Figure 4-16. Stopping a While Loop

National Instruments Corporation

4-29

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Exercise 4-2
Goal

Auto Match VI
Use a While Loop and an iteration terminal and pass data through a tunnel.

Scenario
Create a VI that continuously generates random numbers between 0 and 1000 until it generates a number that matches a number selected by the user. Determine how many random numbers the VI generated before the matching number.

Design
Table 4-2. Inputs and Outputs

Type Input

Name
Number to Match

Properties Double-precision, floating-point between 0 and 1000, coerce to nearest whole number, default value = 50 Double-precision, floating-point Integer

Output Output

Current Number

Number of Iterations

LabVIEW Introduction Course Manual

4-30

ni.com

Lesson 4

Implementing a VI

Flowchart

Generate a Random Number Between 0 and 1

No

Multiply by 1000

Round to Nearest Integer Value

Display Value to User

= Number to Match?

Yes

Add 1 to Iteration Terminal

Display Number of Iterations

Figure 4-17. Auto Match Flowchart

National Instruments Corporation

4-31

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Implementation
Open a blank VI and build the following front panel. Modify the controls and indicators as shown in the following front panel and as described in the following steps.

1. Open a blank VI. 2. Save the VI as Auto Match.vi in the <Exercises>\LabVIEW Basics I\Auto Match directory. 3. Create the Number to Match input. Add a numeric control to the front panel window. Label the control Number to Match. 4. Set the properties for the Number to Match control so that the default value is 50, the data range is from 0 to 1000, the increment value is 1, and the digits of precision is 0. Right-click the Number to Match control and select Data Entry from the shortcut menu. The Data Entry page of the Numeric Properties dialog box appears. Set the Default Value to 50. Set the Minimum value to 0 and select Coerce from the Response to value outside limits pull-down menu. Set the Maximum value to 1000 and select Coerce from the Response to value outside limits pull-down menu. Set the Increment value to 1 and select Coerce to Nearest from the Response to value outside limits pull-down menu.

LabVIEW Introduction Course Manual

4-32

ni.com

Lesson 4

Implementing a VI

Select the Display Format tab. Select Floating Point and change Precision Type from Significant digits to Digits of precision. Enter 0 in the Digits text box and click OK. 5. Create the Current Number output. Add a numeric indicator to the front panel window. Label the indicator Current Number. Right-click the indicator and select AdvancedSynchronous Display. 6. Set the digits of precision for the Current Number output to 0. Right-click the Current Number indicator and select Display Format from the shortcut menu. The Display Format page of the Numeric Properties dialog box appears. Select Floating Point and change Precision Type to Digits of precision. Enter 0 in the Digits text box and click OK. 7. Create the # of iterations output. Place a numeric indicator on the front panel. Label the indicator # of iterations. 8. Set the representation for the # of iterations output to a long integer. Right-click the # of iterations indicator. Select RepresentationI32 from the shortcut menu.

National Instruments Corporation

4-33

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Create the following block diagram. Refer to the following steps for instructions.

9. Generate a random number integer between 0 and 1000. Add the Random Number (0-1) function to the block diagram. The Random Number (0-1) function generates a random number between 0 and 1. Add the Multiply function to the block diagram. The Multiply function multiplies the random number by the y input to produce a random number between 0 and y. Wire the output of the Random Number function to the x input of the Multiply function. Right-click the y input of the Multiply function, select Create Constant from the shortcut menu, enter 1000, and press the <Enter> key to create a numeric constant. Wire the output of the Multiply function to the input of the Round To Nearest function. Add the Round To Nearest function to the block diagram. This function rounds the random number to the nearest integer. Wire the output of the Round To Nearest function to the Current Number indicator.

LabVIEW Introduction Course Manual

4-34

ni.com

Lesson 4

Implementing a VI

10. Compare the randomly generated number to the value in the Number to Match control. Add the Not Equal? function to the block diagram. This function compares the random number with Number to Match and returns True if the numbers are not equal; otherwise, it returns False. Wire the output of the Round To Nearest function to the x input of the Not Equal? function. Wire the Number to Match numeric control to the y input of the Not Equal? function. Wire the output of the Not Equal? function to the conditional terminal. 11. Repeat the algorithm until the Not Equal? function returns True. Add a While Loop from the Structures palette to the block diagram. Right-click the conditional terminal and select Continue if True from the shortcut menu. 12. Display the number of random numbers generated to the user by adding one to the iteration terminal value. Wire the iteration terminal to the border of the While Loop. A blue tunnel appears on the While Loop border.
Tip Each time the loop executes, the iteration terminal increments by one. Wire the iteration value to the Increment function because the iteration count starts at 0. The iteration count passes out of the loop upon completion.

Add the Increment function to the block diagram. This function adds 1 to the While Loop count. 13. Save the VI.

National Instruments Corporation

4-35

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Test
1. Display the front panel. 2. Change the number in Number to Match to a number that is in the data range, which is 0 to 1000 with an increment of 1. 3. Run the VI. 4. Change Number to Match and run the VI again. Current Number updates at every iteration of the loop because it is inside the loop. # of iterations updates upon completion because it is outside the loop. 5. To see how the VI updates the indicators, enable execution highlighting. On the block diagram toolbar, click the Highlight Execution button to enable execution highlighting. Execution highlighting shows the movement of data on the block diagram from one node to another so you can see each number as the VI generates it. 6. Run the VI and observe the data flow. 7. Try to match a number that is outside the data range. 8. Change Number to Match to a number that is out of the data range. Run the VI. LabVIEW coerces the out-of-range value to the nearest value in the specified data range. 9. Close the VI.

End of Exercise 4-2

LabVIEW Introduction Course Manual

4-36

ni.com

Lesson 4

Implementing a VI

E. For Loops
A For Loop executes a subdiagram a set number of times. Figure 4-18 shows a For Loop in LabVIEW, a flowchart equivalent of the For Loop functionality, and a pseudo code example of the functionality of the For Loop.

N=100

i=0 i=i+1 Code i=N? Yes End; End 1 2 3 No Code N=100; i=0; Until i=N: Repeat (code; i=i+1);

LabVIEW For Loop

Flowchart

Pseudo Code

Figure 4-18. For Loop

The For Loop is located on the Structures palette. You also can place a While Loop on the block diagram, right-click the border of the While Loop, and select Replace with For Loop from the shortcut menu to change a While Loop to a For Loop. The count terminal, shown as follows, is an input terminal whose value indicates how many times to repeat the subdiagram.

The iteration terminal, shown as follows, is an output terminal that contains the number of completed iterations.

The iteration count always starts at zero. During the first iteration, the iteration terminal returns 0. If the iteration count exceeds 2,147,483,647, or 231, the iteration terminal will remain at 2,147,483,647 for all further iterations. If you need to keep count of more than 2,147,483,647 iterations, you can use shift registers with a greater integer range. The For Loop differs from the While Loop in that the For Loop executes a set number of times. A While Loop stops executing the subdiagram only if the value at the conditional terminal exists.

National Instruments Corporation

4-37

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

The following For Loop generates a random number every second for 100 seconds and displays the random numbers in a numeric indicator.

Figure 4-19. For Loop Example

Adding a Conditional Terminal to a For Loop

If necessary, you can add a conditional terminal to configure a For Loop to stop when a Boolean condition or an error occurs. A For Loop with a conditional terminal executes until the condition occurs or until all iterations are complete, whichever happens first. For Loops you configure for a conditional exit have a red glyph in the count terminal as well as a conditional terminal in the lower right corner. After you configure the For Loop to exit conditionally, the loop appears similar to Figure 4-20. The following For Loop generates a random number every second until 100 seconds has passed or the user clicks the stop button.

Figure 4-20. For Loop Configured for a Conditional Exit

LabVIEW Introduction Course Manual

4-38

ni.com

Lesson 4

Implementing a VI

To add a conditional terminal to a For Loop, right-click on the For Loop border and select Conditional Terminal from the shortcut menu. Then wire the conditional terminal and the count terminal.

Figure 4-21. Adding a Conditional Terminal to a For Loop

Numeric Conversion
LabVIEW can represent numeric data types as signed or unsigned integers, floating-point numeric values, or complex numeric values, as discussed in the LabVIEW Data Types section of this lesson. Normally, when you wire different representation types to the inputs of a function, the function returns an output in the larger or wider format. LabVIEW chooses the representation that uses more bits. If the number of bits is the same, LabVIEW chooses unsigned over signed integers. For example, if you wire a DBL and an I32 to a Multiply function, the result is a DBL, as shown in Figure 4-22. LabVIEW coerces the 32-bit signed integer because it uses fewer bits than the double-precision, floating-point numeric value. The lower input of the Multiply function shows a grey dot, called a coercion dot, that indicates LabVIEW coerced the data.

Coercion Dot

Figure 4-22. Numeric Conversion Example

National Instruments Corporation

4-39

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

However, the For Loop count terminal works in the opposite manner. If you wire a double-precision, floating-point numeric value to the 32-bit count terminal, LabVIEW coerces the larger numeric value to a 32-bit signed integer. Although the conversion is contrary to normal conversion standards, it is necessary, because a For Loop can only execute an integer number of times.

Coercion Dot

Figure 4-23. Coercion on a For Loop

LabVIEW Introduction Course Manual

4-40

ni.com

Lesson 4

Implementing a VI

Exercise 4-3
Goal

Concept: While Loops versus For Loops

Understand when to use a While Loop and when to use a For Loop.

Description
For the following scenarios, decide whether to use a While Loop or a For Loop.

Scenario 1
Acquire pressure data every second for one minute. 1. If you use a While Loop, what is the condition that you need to stop the loop? 2. If you use a For Loop, how many iterations does the loop need to run? 3. Is it easier to implement a For Loop or a While Loop?

Scenario 2
Acquire pressure data until the pressure is 1400 psi. 1. If you use a While Loop, what is the condition that you need to stop the loop? 2. If you use a For Loop, how many iterations does the loop need to run? 3. Is it easier to implement a For Loop or a While Loop?

National Instruments Corporation

4-41

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Scenario 3
Acquire pressure and temperature data until both values are stable for two minutes. 1. If you use a While Loop, what is the condition that you need to stop the loop? 2. If you use a For Loop, how many iterations does the loop need to run? 3. Is it easier to implement a For Loop or a While Loop?

Scenario 4
Output a voltage ramp starting at zero, increasing incrementally by 0.5 V every second, until the output voltage is equal to 5 V. 1. If you use a While Loop, what is the condition that you need to stop the loop? 2. If you use a For Loop, how many iterations does the loop need to run? 3. Is it easier to implement a For Loop or a While Loop?

LabVIEW Introduction Course Manual

4-42

ni.com

Lesson 4

Implementing a VI

Answers Scenario 1
Acquire pressure data every second for one minute. 1. While Loop: Time = 1 minute 2. For Loop: 60 iterations 3. Both are possible.

Scenario 2
Acquire pressure data until the pressure is 1400 psi. 1. While Loop: Pressure = 1400 psi 2. For Loop: unknown 3. A While Loop. Although you can add a conditional terminal to a For Loop, you still need to wire a value to the count terminal. Without more information, you do not know the appropriate value to wire to the count terminal.

Scenario 3
Acquire pressure and temperature data until both values are stable for two minutes. 1. While Loop: [(Last Temperature = Previous Temperature) for 2 minutes or more] and [(Last Pressure = Previous Pressure) for 2 minutes or more] 2. For Loop: unknown 3. A While Loop. Although you can add a conditional terminal to a For Loop, you still need to wire a value to the count terminal. Without more information, you do not know the appropriate value to wire to the count terminal.

Scenario 4
Output a voltage ramp starting at zero, increasing incrementally by 0.5 V every second, until the output voltage is equal to 5 V. 1. While Loop: Voltage = 5 V 2. For Loop: 11 iterations 3. Both are possible.

End of Exercise 4-3

National Instruments Corporation

4-43

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

F. Timing a VI
When a loop finishes executing an iteration, it immediately begins executing the next iteration, unless it reaches a stop condition. Most often, you need to control the iteration frequency or timing. For example, if you are acquiring data, and you want to acquire the data once every 10 seconds, you need a way to time the loop iterations so they occur once every 10 seconds. Even if you do not need the execution to occur at a certain frequency, you need to provide the processor with time to complete other tasks, such as responding to the user interface. This section introduces some methods for timing your loops.

Wait Functions
Place a wait function inside a loop to allow a VI to sleep for a set amount of time. This allows your processor to address other tasks during the wait time. Wait functions use the millisecond clock of the operating system. The Wait Until Next ms Multiple function monitors a millisecond counter and waits until the millisecond counter reaches a multiple of the amount you specify. Use this function to synchronize activities. Place this function in a loop to control the loop execution rate. For this function to be effective, your code execution time must be less than the time specified for this function. The execution rate for the first iteration of the loop is indeterminate. The Wait (ms) function waits until the millisecond counter counts to an amount equal to the input you specify. This function guarantees that the loop execution rate is at least the amount of the input you specify.
Note The Time Delay Express VI behaves similar to the Wait (ms) function with the addition of built-in error clusters. Refer to Lesson 3, Troubleshooting and Debugging VIs, for more information about error clusters.

Elapsed Time
In some cases, it is useful to determine how much time elapses after some point in your VI. The Elapsed Time Express VI indicates the amount of time that elapses after the specified start time. This Express VI keeps track of time while the VI continues to execute. This Express VI does not provide the processor with time to complete other tasks. You will use the Elapsed Time Express VI in the Weather Station course project.

LabVIEW Introduction Course Manual

4-44

ni.com

Lesson 4

Implementing a VI

G. Iterative Data Transfer

When programming with loops, you often must access data from previous iterations of the loop in LabVIEW. For example, if you are acquiring one piece of data in each iteration of a loop and must average every five pieces of data, you must retain the data from previous iterations of the loop. Shift registers transfer values from one loop iteration to the next. Feedback Nodes are another method for retaining information from a previous iteration. Refer to the Feedback Node topic of the LabVIEW Help for more information about Feedback Nodes.
Note

Shift registers are similar to static variables in text-based programming languages. Use shift registers when you want to pass values from previous iterations through the loop to the next iteration. A shift register appears as a pair of terminals, shown as follows, directly opposite each other on the vertical sides of the loop border.

The terminal on the right side of the loop contains an up arrow and stores data on the completion of an iteration. LabVIEW transfers the data connected to the right side of the register to the next iteration. After the loop executes, the terminal on the right side of the loop returns the last value stored in the shift register. Create a shift register by right-clicking the left or right border of a loop and selecting Add Shift Register from the shortcut menu. A shift register transfers any data type and automatically changes to the data type of the first object wired to the shift register. The data you wire to the terminals of each shift register must be the same type. You can add more than one shift register to a loop. If you have multiple operations that use previous iteration values within your loop, use multiple shift registers to store the data values from those different processes in the structure, as shown in the following figure.

National Instruments Corporation

4-45

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Initializing Shift Registers

Initializing a shift register resets the value the shift register passes to the first iteration of the loop when the VI runs. Initialize a shift register by wiring a control or constant to the shift register terminal on the left side of the loop, as shown in the following block diagram.

In the previous block diagram, the For Loop executes five times, incrementing the value the shift register carries by one each time. After five iterations of the For Loop, the shift register passes the final value, 5, to the indicator and the VI quits. Each time you run the VI, the shift register begins with a value of 0. If you do not initialize the shift register, the loop uses the value written to the shift register when the loop last executed or, if the loop has never executed, the default value for the data type. Use an uninitialized shift register to preserve state information between subsequent executions of a VI. The following block diagram shows an uninitialized shift register.

LabVIEW Introduction Course Manual

4-46

ni.com

Lesson 4

Implementing a VI

In the previous block diagram, the For Loop executes five times, incrementing the value the shift register carries by one each time. The first time you run the VI, the shift register begins with a value of 0, which is the default value for a 32-bit integer. After five iterations of the For Loop, the shift register passes the final value, 5, to the indicator, and the VI quits. The next time you run the VI, the shift register begins with a value of 5, which was the last value from the previous execution. After five iterations of the For Loop, the shift register passes the final value, 10, to the indicator. If you run the VI again, the shift register begins with a value of 10, and so on. Uninitialized shift registers retain the value of the previous iteration until you close the VI.

Stacked Shift Registers

Stacked shift registers let you access data from previous loop iterations. Stacked shift registers remember values from multiple previous iterations and carry those values to the next iterations. To create a stacked shift register, right-click the left terminal and select Add Element from the shortcut menu. Stacked shift registers can occur only on the left side of the loop because the right terminal transfers the data generated from only the current iteration to the next iteration, as shown in the following block diagram.

If you add another element to the left terminal in the previous block diagram, values from the last two iterations carry over to the next iteration, with the most recent iteration value stored in the top shift register. The bottom terminal stores the data passed to it from the previous iteration.

National Instruments Corporation

4-47

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Exercise 4-4
Goal

Average Temperature VI
Use a While Loop and shift registers to average data.

Scenario
The Temperature Monitor VI acquires and displays temperature. Modify the VI to average the last three temperature measurements and display the running average on the waveform chart.

Design
Figure 4-24 and Figure 4-25 show the Temperature Monitor VI front panel and block diagram.

Figure 4-24. Temperature Monitor VI Front Panel

Figure 4-25. Temperature Monitor VI Block Diagram

To modify this VI, you need to retain the temperature values from the previous two iterations, and average the values. Use a shift register with an additional element to retain data from the previous two iterations. Initialize the shift register with a reading from the temperature sensor. Chart only the average temperature.

LabVIEW Introduction Course Manual

4-48

ni.com

Lesson 4

Implementing a VI

Implementation
1. Test the VI. If you have hardware, follow the instructions in the Hardware Installed column. Otherwise, follow the instructions in the No Hardware Installed column. Hardware Installed Open the Temperature Monitor VI in the
<Exercises>\LabVIEW Basics I\ Average Temperature directory.

No Hardware Installed Open Temperature Monitor (Demo) VI in the

<Exercises>\LabVIEW Basics I\ No Hardware Required\Average Temperature directory.

Select FileSave As and rename the VI Average Temperature.vi in the

<Exercises>\LabVIEW Basics I\ Average Temperature directory.

Select FileSave As and rename the VI Average Temperature.vi in the

<Exercises>\LabVIEW Basics I\ No Hardware Required\Average Temperature directory.

On the DAQ Signal Accessory, flip the temperature sensor noise switch to the On position. This switch introduces noise to the temperature reading. Run the VI. Place your finger on the temperature sensor of the DAQ Signal Accessory to increase the temperature reading. You can quickly move your finger across the sensor to increase the reading even more through friction. Notice the number of spikes in the reading.

Run the VI. Notice the variation in the simulated temperature reading.

2. Stop the VI by changing the state of the Power switch on the front panel. Notice that the Power switch immediately switches back to the On state. The mechanical action of the switch controls this behavior. In the following steps, modify the VI to reduce the number of temperature spikes. 3. Display the block diagram.

National Instruments Corporation

4-49

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

4. Modify the block diagram as shown in Figure 4-26.

Figure 4-26. Average Temperature VI Block Diagram

Right-click the right or left border of the While Loop and select Add Shift Register from the shortcut menu to create a shift register. Right-click the left terminal of the shift register and select Add Element from the shortcut menu to add an element to the shift register. Press the <Ctrl> key while you click the Thermometer VI and drag it outside the While Loop to create a copy of the subVI. The Thermometer VI returns one temperature measurement from the temperature sensor and initializes the left shift registers before the loop starts. Place the Compound Arithmetic function on the block diagram. Configure this function to return the sum of the current temperature and the two previous temperature readings. Use the Positioning tool to resize the Compound Arithmetic function to have three left terminals.

Place the Divide function on the block diagram. This function returns the average of the last three temperature readings. Wire the functions together as shown in Figure 4-26. Right-click the y input of the Divide function and select Create Constant. Enter 3 and press the <Enter> key. 5. Save the VI.

LabVIEW Introduction Course Manual

4-50

ni.com

Lesson 4

Implementing a VI

Test
1. Run the VI. 2. If you have hardware installed, place your finger on the temperature sensor of the DAQ Signal Accessory to increase the temperature reading. During each iteration of the While Loop, the Thermometer VI takes one temperature measurement. The VI adds this value to the last two measurements stored in the left terminals of the shift register. The VI divides the result by three to find the average of the three measurementsthe current measurement plus the previous two. The VI displays the average on the waveform chart. Notice that the VI initializes the shift register with a temperature measurement. 3. Stop the VI by changing the state of the Power switch on the front panel. 4. Close the VI.

End of Exercise 4-4

National Instruments Corporation

4-51

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

H. Plotting Data
You already used charts and graphs to plot simple data. This section explains more about using and customizing charts and graphs.

Waveform Charts
The waveform chart is a special type of numeric indicator that displays one or more plots of data typically acquired at a constant rate. Waveform charts can display single or multiple plots. Figure 4-27 shows the elements of a multiplot waveform chart. Two plots are displayed: Raw Data and Running Avg.

3 5

1 2

Label Y-scale

3 4

X-scale Scale Legend

5 6

Graph Palette Plot Legend

Figure 4-27. Waveform Charts

You can configure how the chart updates to display new data. Right-click the chart and select AdvancedUpdate Mode from the shortcut menu to set the chart update mode. The chart uses the following modes to display data: Strip ChartShows running data continuously scrolling from left to right across the chart with old data on the left and new data on the right. A strip chart is similar to a paper tape strip chart recorder. Strip Chart is the default update mode. Scope ChartShows one item of data, such as a pulse or wave, scrolling partway across the chart from left to right. For each new value, the chart plots the value to the right of the last value. When the plot reaches the right border of the plotting area, LabVIEW erases the plot

LabVIEW Introduction Course Manual

4-52

ni.com

Lesson 4

Implementing a VI

and begins plotting again from the left border. The retracing display of a scope chart is similar to an oscilloscope. Sweep ChartWorks similarly to a scope chart except it shows the old data on the right and the new data on the left separated by a vertical line. LabVIEW does not erase the plot in a sweep chart when the plot reaches the right border of the plotting area. A sweep chart is similar to an EKG display.

Figure 4-28 shows an example of each chart update mode. The scope chart and sweep chart have retracing displays similar to an oscilloscope. Because retracing a plot requires less overhead, the scope chart and the sweep chart display plots significantly faster than the strip chart.

Figure 4-28. Chart Update Modes

Wiring Charts
You can wire a scalar output directly to a waveform chart. The waveform chart terminal shown in Figure 4-29 matches the input data type.

Figure 4-29. Wiring a Single Plot to a Waveform Chart

National Instruments Corporation

4-53

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Waveform charts can display multiple plots together using the Bundle function located on the Cluster & Variant palette. In Figure 4-30, the Bundle function bundles the outputs of the three VIs to plot on the waveform chart.

Figure 4-30. Wiring Multiple Plots to a Waveform Chart

The waveform chart terminal changes to match the output of the Bundle function. To add more plots, use the Positioning tool to resize the Bundle function. Refer to Lesson 5, Relating Data, for more information about the Bundle function.

Waveform Graphs
VIs with a graph usually collect the data in an array and then plot the data to the graph. Figure 4-31 shows the elements of a graph.

11

2 3 4 5

10 6 9

7 8

1 2 3

Plot Legend Cursor Grid Mark

4 5 6

Mini-Grid Mark Scale Legend Cursor Mover

7 8 9

Cursor Legend Graph Palette X-Scale

10 Y-Scale 11 Label

Figure 4-31. Waveform Graph

LabVIEW Introduction Course Manual

4-54

ni.com

Lesson 4

Implementing a VI

The graphs located on the Graph Indicators palette include the waveform graph and XY graph. The waveform graph plots only single-valued functions, as in y = f(x), with points evenly distributed along the x-axis, such as acquired time-varying waveforms. XY graphs display any set of points, evenly sampled or not. Resize the plot legend to display multiple plots. Use multiple plots to save space on the front panel and to make comparisons between plots. XY and waveform graphs automatically adapt to multiple plots.

Single Plot Waveform Graphs

The waveform graph accepts several data types for single-plot waveform graphs. The graph accepts a single array of values, interprets the data as points on the graph, and increments the x index by one starting at x = 0. The graph accepts a cluster of an initial x value, a delta x, and an array of y data. The graph also accepts the waveform data type, which carries the data, start time, and delta t of a waveform. Refer to the Waveform Graph VI in the labview\examples\ general\graphs\gengraph.llb for examples of the data types that a waveform graph accepts.

Multiplot Waveform Graphs

The waveform graph accepts several data types for displaying multiple plots. The waveform graph accepts a 2D array of values, where each row of the array is a single plot. The graph interprets the data as points on the graph and increments the x index by one, starting at x = 0. Wire a 2D array data type to the graph, right-click the graph, and select Transpose Array from the shortcut menu to handle each column of the array as a plot. This is particularly useful when you sample multiple channels from a DAQ device because the device can return the data as 2D arrays with each channel stored as a separate column. Refer to the (Y) Multi Plot 1 graph in the Waveform Graph VI in the labview\examples\general\graphs\gengraph.llb for an example of a graph that accepts this data type. The waveform graph also accepts a cluster of an initial x value, a delta x value, and a 2D array of y data. The graph interprets the y data as points on the graph and increments the x index by delta x, starting at the initial x value. This data type is useful for displaying multiple signals that are sampled at the same regular rate. Refer to the (Xo = 10, dX = 2, Y) Multi Plot 2 graph in the Waveform Graph VI in the labview\examples\general\ graphs\gengraph.llb for an example of a graph that accepts this data type.

National Instruments Corporation

4-55

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

The waveform graph accepts a plot array where the array contains clusters. Each cluster contains a 1D array that contains the y data. The inner array describes the points in a plot, and the outer array has one cluster for each plot. The following front panel shows this array of the y cluster.

Use a plot array instead of a 2D array if the number of elements in each plot is different. For example, when you sample data from several channels using different time amounts from each channel, use this data structure instead of a 2D array because each row of a 2D array must have the same number of elements. The number of elements in the interior arrays of an array of clusters can vary. Refer to the (Y) Multi Plot 2 graph in the Waveform Graph VI in the labview\examples\general\graphs\gengraph.llb for an example of a graph that accepts this data type. The waveform graph accepts a cluster of an initial x value, a delta x value, and array that contains clusters. Each cluster contains a 1D array that contains the y data. You use the Bundle function to bundle the arrays into clusters and you use the Build Array function to build the resulting clusters into an array. You also can use the Build Cluster Array function, which creates arrays of clusters that contain the inputs you specify. Refer to the (Xo = 10, dX = 2, Y) Multi Plot 3 graph in the Waveform Graph VI in the labview\examples\general\graphs\gengraph.llb for an example of a graph that accepts this data type. The waveform graph accepts an array of clusters of an x value, a delta x value, and an array of y data. This is the most general of the multiple-plot waveform graph data types because you can indicate a unique starting point and increment for the x-scale of each plot. Refer to the (Xo = 10, dX = 2, Y) Multi Plot 1 graph in the Waveform Graph VI in the labview\examples\ general\graphs\gengraph.llb for an example of a graph that accepts this data type. The waveform graph also accepts the dynamic data type, which is for use with Express VIs. In addition to the data associated with a signal, the dynamic data type includes attributes that provide information about the signal, such as the name of the signal or the date and time the data was acquired. Attributes specify how the signal appears on the waveform graph. When the dynamic data type includes multiple channels, the graph displays a plot for each channel and automatically formats the plot legend and x-scale time stamp.

LabVIEW Introduction Course Manual

4-56

ni.com

Lesson 4

Implementing a VI

Single Plot XY Graphs

The XY graph accepts three data types for single-plot XY graphs. The XY graph accepts a cluster that contains an x array and a y array. Refer to the (X and Y arrays) Single Plot graph in the XY Graph VI in the labview\ examples\general\graphs\gengraph.llb for an example of a graph that accepts this data type. The XY graph also accepts an array of points, where a point is a cluster that contains an x value and a y value. Refer to the (Array of Pts) Single Plot graph in the XY Graph VI in the labview\examples\general\ graphs\gengraph.llb for an example of a graph that accepts this data type. The XY graph also accepts an array of complex data, in which the real part is plotted on the x-axis and the imaginary part is plotted on the y-axis.

Multiplot XY Graphs
The XY graph accepts three data types for displaying multiple plots. The XY graph accepts an array of plots, where a plot is a cluster that contains an x array and a y array. Refer to the (X and Y arrays) Multi Plot graph in the XY Graph VI in the labview\examples\general\graphs\ gengraph.llb for an example of a graph that accepts this data type. The XY graph also accepts an array of clusters of plots, where a plot is an array of points. A point is a cluster that contains an x value and a y value. Refer to the (Array of Pts) Multi Plot graph in the XY Graph VI in the labview\examples\general\graphs\gengraph.llb for an example of a graph that accepts this data type. The XY graph also accepts an array of clusters of plots, where a plot is an array of complex data, in which the real part is plotted on the x-axis and the imaginary part is plotted on the y-axis.

National Instruments Corporation

4-57

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Exercise 4-5
Goal

Temperature Multiplot VI
Plot multiple data sets on a single waveform chart and customize the chart view.

Scenario
Modify the VI from Exercise 4-4 to plot both the current temperature and the running average on the same chart. In addition, allow the user to examine a portion of the plot while the data is being acquired.

Design
Figure 4-32 shows the front panel for the existing VI (Average Temperature VI) and Figure 4-33 shows the block diagram.

Figure 4-32. Average Temperature VI Front Panel

To allow the user to examine a portion of the plot while the data is being acquired, display the scale legend and the graph palette for the waveform chart. Also, expand the legend to show additional plots. To modify the block diagram in Figure 4-33, you must modify the chart terminal to accept multiple pieces of data. Use a Bundle function to combine the average temperature and the current temperature into a cluster to pass to the Temperature History chart terminal.

LabVIEW Introduction Course Manual

4-58

ni.com

Lesson 4

Implementing a VI

Figure 4-33. Average Temperature VI Block Diagram

Implementation
1. Open the VI created in Exercise 4-4. If you have hardware, follow the instructions in the Hardware Installed column. Otherwise, follow the instructions in the No Hardware Installed column. Hardware Installed Open Average Temperature VI in the
<Exercises>\LabVIEW Basics I\ Average Temperature directory.

No Hardware Installed Open Average Temperature VI in the

<Exercises>\LabVIEW Basics I\ No Hardware Required\Average Temperature directory.

Select FileSave As and rename the VI Temperature Multiplot.vi in the

<Exercises>\LabVIEW Basics I\ Temperature Multiplot directory.

Select FileSave As and rename the VI Temperature Multiplot.vi in the

<Exercises>\LabVIEW Basics I\ No Hardware Required\Temperature Multiplot directory.

Select the Substitute Copy for Original option to close the Average Temperature VI and work in the Temperature Multiplot VI. You can create the directory if it does not exist.
Tip

National Instruments Corporation

4-59

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

In the steps below, you modify the block diagram similar to that shown in Figure 4-34. Modify the block diagram first, then modify the front panel.

Figure 4-34. Temperature Multiplot VI Block Diagram

2. Open the block diagram. 3. Pass the current temperature and the average temperature to the Temperature History chart terminal. Delete the wire connecting the Divide function to the Temperature History chart terminal. Add a Bundle function between the Divide function and the Temperature History chart indicator. If necessary, enlarge the While Loop to make space. Wire the output of the Divide function to the top input of the Bundle function. Wire the current temperature to the bottom input of the Bundle function. The current temperature is the output of the Thermometer subVI inside the While Loop. Wire the output of the Bundle function to the Temperature History chart indicator.

LabVIEW Introduction Course Manual

4-60

ni.com

Lesson 4

Implementing a VI

In the following steps, modify the front panel similar to the one shown in Figure 4-35.

Figure 4-35. Temperature Multiplot VI Front Panel

4. Open the front panel. 5. Show both plots in the plot legend of the waveform chart. Use the Positioning tool to resize the plot legend to two objects, using the top middle resizing node. Rename the top plot Running Avg. Rename the bottom plot Current Temp. Change the plot type of Current Temp. Use the Operating tool to select the plot in the plot legend and choose the plots you want. The order of the plots listed in the plot legend is the same as the order of the items wired to the Bundle function on the block diagram.
Tip

6. Show the scale legend and graph palette of the waveform chart. Right-click the Temperature History waveform chart and select Visible ItemsScale Legend from the shortcut menu. Right-click the Temperature History waveform chart and select Visible ItemsGraph Palette from the shortcut menu. 7. Save the VI.

National Instruments Corporation

4-61

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Test
1. Run the VI. Use the tools in the scale legend and the graph palette to examine the data as it generates. 2. Change the Power switch to the Off position to stop the VI. 3. Close the VI when you are finished.

End of Exercise 4-5

LabVIEW Introduction Course Manual

4-62

ni.com

Lesson 4

Implementing a VI

I. Case Structures
A Case structure, shown as follows, has two or more subdiagrams, or cases.

Only one subdiagram is visible at a time, and the structure executes only one case at a time. An input value determines which subdiagram executes. The Case structure is similar to switch statements or if...then...else statements in text-based programming languages. The case selector label at the top of the Case structure, shown as follows, contains the name of the selector value that corresponds to the case in the center and decrement and increment arrows on each side.

Click the decrement and increment arrows to scroll through the available cases. You also can click the down arrow next to the case name and select a case from the pull-down menu. Wire an input value, or selector, to the selector terminal, shown as follows, to determine which case executes.

You must wire an integer, Boolean value, string, or enumerated type value to the selector terminal. You can position the selector terminal anywhere on the left border of the Case structure. If the data type of the selector terminal is Boolean, the structure has a TRUE case and a FALSE case. If the selector terminal is an integer, string, or enumerated type value, the structure can have any number of cases. If you do not specify a default case for the Case structure to handle out-of-range values, you must explicitly list every possible input value. For example, if the selector is an integer and you specify cases for 1, 2, and 3, you must specify a default case to execute if the input value is 4 or any other unspecified integer value. Right-click the Case structure border to add, duplicate, remove, or rearrange cases, and to select a default case.

National Instruments Corporation

4-63

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Selecting a Case
Figure 4-36 shows a VI that uses a Case structure to execute different code dependent on whether a user selects C or F for temperature units. The top block diagram shows the True case in the foreground. In the middle block diagram, the False case is selected. To select a case, enter the value in the case selector identifier or use the Labeling tool to edit the values. After you select another case, that case displays on the block diagram, as shown in the bottom block diagram of Figure 4-36.

Figure 4-36. Changing the Case View of a Case Structure

If you enter a selector value that is not the same type as the object wired to the selector terminal, the value appears red. This indicates that the VI will not run until you delete or edit the value. Also, because of the possible round-off error inherent in floating-point arithmetic, you cannot use floating-point numbers as case selector values. If you wire a floating-point value to the case, LabVIEW rounds the value to the nearest even integer. If you type a floating-point value in the case selector label, the value appears red to indicate that you must delete or edit the value before the structure can execute.

LabVIEW Introduction Course Manual

4-64

ni.com

Lesson 4

Implementing a VI

Input and Output Tunnels

You can create multiple input and output tunnels for a Case structure. Inputs are available to all cases, but cases do not need to use each input. However, you must define an output tunnel for each case. Consider the following example: a Case structure on the block diagram has an output tunnel, but in at least one of the cases, there is no output value wired to the tunnel. If you run this case, LabVIEW does not know what value to return for the output. LabVIEW indicates this error by leaving the center of the tunnel white. The unwired case might not be the case that is currently visible on the block diagram. To correct this error, display the case(s) that contain(s) the unwired output tunnel and wire an output to the tunnel. You also can right-click the output tunnel and select Use Default If Unwired from the shortcut menu to use the default value for the tunnel data type for all unwired tunnels. When the output is wired in all cases, the output tunnel is a solid color. Avoid using the Use Default If Unwired option. Using this option does not document the block diagram well, and can confuse other programmers using your code. The Use Default If Unwired option also makes debugging code difficult. If you use this option, be aware that the default value used is the default value for the data type that is wired to the tunnel. For example, if the tunnel is a Boolean data type, the default value is FALSE. Refer to Table 4-3 for a list of default values for data types.
Table 4-3. Data Type Default Values

Data Type Numeric Boolean String

0 FALSE

Default Value

empty ()

National Instruments Corporation

4-65

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Examples
In the following examples, the numeric values pass through tunnels to the Case structure and are either added or subtracted, depending on the value wired to the selector terminal.

Boolean Case Structure

The following example is a Boolean Case structure. The cases overlap each other to simplify the illustration.

If the Boolean control wired to the selector terminal is True, the VI adds the numeric values. Otherwise, the VI subtracts the numeric values.

Integer Case Structure

The following example is an integer Case structure.

Integer is a text ring control located on the Text Controls palette that associates numeric values with text items. If the Integer wired to the selector terminal is 0 (add), the VI adds the numeric values. If the value is 1 (subtract), the VI subtracts the numeric values. If Integer is any other value than 0 (add) or 1 (subtract), the VI adds the numeric values, because that is the default case.

LabVIEW Introduction Course Manual

4-66

ni.com

Lesson 4

Implementing a VI

String Case Structure

The following example shows a string Case structure.

If String is add, the VI adds the numeric values. If String is subtract, the VI subtracts the numeric values.

Enumerated Case Structure

The following example is an enumerated Case structure.

An enumerated type control gives users a list of items from which to select. The data type of an enumerated type control includes information about the numeric values and string labels in the control. The case selector displays the string label for each item in the enumerated type control when you select Add Case For Every Value from the Case structure shortcut menu. The Case structure executes the appropriate case subdiagram based on the current item in the enumerated type control. In the previous block diagram, if Enum is add, the VI adds the numeric values. If Enum is subtract, the VI subtracts the numeric values.

National Instruments Corporation

4-67

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Using Case Structures for Error Handling

The following example shows a Case structure where an error cluster defines the cases.

Figure 4-37. No Error Case

Figure 4-38. Error Case

When you wire an error cluster to the selector terminal of a Case structure, the case selector label displays two casesError and No Errorand the border of the Case structure changes colorred for Error and green for No Error. If an error occurs, the Case structure executes the Error subdiagram. When you wire an error cluster to the selection terminal, the Case structure recognizes only the status Boolean element of the cluster.

LabVIEW Introduction Course Manual

4-68

ni.com

Lesson 4

Implementing a VI

Exercise 4-6
Goal

Determine Warnings VI
Modify a VI to use a Case structure to make a software decision.

Scenario
You created a VI where a user inputs a temperature, a maximum temperature, and a minimum temperature. A warning string generates depending on the relationship of the given inputs. However, a situation could occur that causes the VI to work incorrectly. The user could enter a maximum temperature that is less than the minimum temperature. Modify the VI to generate a different string to alert the user to the error: "Upper Limit < Lower Limit." Set the Warning? indicator to True to indicate the error.

Design
Modify the flowchart created for the original Determine Warnings VI as shown in Figure 4-39.

Min. Temp Min Temp >= Max Temp Yes

No

Current Temp Min Temp >= Max Temp Max Temp Yes Output Heatstroke Warning and TRUE

No

Current Temp Min. Temp Yes Output Freeze Warning and TRUE

No

Output No Warning and FALSE

Create Error

Output Upper Limit < Lower Limit and TRUE

Figure 4-39. Modified Determine Warnings Flowchart

The original block diagram for the Determine Warnings VI appears in Figure 4-40. This VI must have a Case structure added to execute the code if the maximum temperature is greater than or equal to the minimum

National Instruments Corporation

4-69

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

temperature. Otherwise, the code will not execute. Instead, a new string is generated and the Warning? indicator is set to True.

Figure 4-40. Determine Warnings VI Block Diagram

Implementation
Complete the following instructions to modify the block diagram similar to that shown in Figure 4-41. This VI is part of the temperature weather station project.

Figure 4-41. Determine Warnings VI Block Diagram

1. Open the Determine Warnings VI in the <Exercises>\LabVIEW Basics I\Determine Warnings directory. 2. Open the block diagram.

LabVIEW Introduction Course Manual

4-70

ni.com

Lesson 4

Implementing a VI

3. Create space on the block diagram to add the Case structure. The Max Temp and Min Temp controls and the Warning Text and Warning? indicators should be outside of the new Case structure, because both cases of the Case structure use these indicators and controls. Select the Min Temp and Max Temp control terminals.
Tip

To select more than one item press the <Shift> key while you select the items. While the terminals are still selected, use the left arrow key on the keyboard to move the controls to the left.

Tip

Press and hold the <Shift> key to move the objects in five pixel increments. Select the Warning Text and Warning? indicator terminals. Align the terminals by selecting Align ObjectsLeft Edges. While the terminals are still selected, use the right arrow key on the keyboard to move the indicators to the right. 4. Compare Min Temp and Max Temp. Add the Greater? function to the block diagram. Wire the Min Temp output to the x input of the Greater? function. Wire the Max Temp output to the y input of the Greater? function. Add a Case structure around the block diagram code, except for the excluded terminals. Wire the output of the Greater? function to the case selector of the Case structure. 5. If Min Temp is less than Max Temp, execute the code that determines the warning string and indicator. While the True case is visible, right-click the border of the Case structure, and select Make This Case False from the shortcut menu. When you create a Case structure around existing code, the code is automatically placed in the True case.

National Instruments Corporation

4-71

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

6. If Min Temp is greater than Max Temp, create a custom string for the Warning Text indicator and set the Warning? indicator to True, as shown in Figure 4-42.

Figure 4-42. Determine Warnings VI Block Diagram

Select the True case. Right-click the string output tunnel. Select CreateConstant. Enter Upper Limit < Lower Limit in the constant. Right-click the Warning? output tunnel. Select CreateConstant. Use the Operating tool to change the constant to a True constant. 7. Save the VI.

Test
1. Switch to the front panel of the VI. 2. Resize the Warning Text indicator to a length to accommodate the new string.

LabVIEW Introduction Course Manual

4-72

ni.com

Lesson 4

Implementing a VI

3. Test the VI by entering values from Table 4-4 for Current Temp, Max Temp, and Min Temp, and running the VI for each set of data. Table 4-4 shows the expected Warning Text and Warning? Boolean value for each set of data.
Table 4-4. Testing Values for Determine Warnings.vi

Current Temp
30 25 10 25

Max Temp
30 30 30 20

Min Temp
10 10 10 30

Warning Text
Heatstroke Warning No Warning Freeze Warning Upper Limit < Lower Limit

Warning? True False True True

4. Save and close the VI.

End of Exercise 4-6

National Instruments Corporation

4-73

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

J. Formula Nodes
When you want to use a complicated equation in LabVIEW, you do not have to wire together various arithmetic functions on the block diagram. You can develop equations in a familiar, mathematical environment and then integrate the equations into an application. The Formula Node is a convenient text-based node you can use to perform mathematical operations on the block diagram. You do not have to access any external code or applications, and you do not have to wire low-level arithmetic functions to create equations. In addition to text-based equation expressions, the Formula Node can accept text-based versions of if statements, while loops, for loops, and do loops, which are familiar to C programmers. These programming elements are similar to what you find in C programming but are not identical. Formula Nodes are useful for equations that have many variables or are otherwise complicated and for using existing text-based code. You can copy and paste the existing text-based code into a Formula Node rather than recreating it graphically. Create the input and output terminals of the Formula Node by right-clicking the border of the node and selecting Add Input or Add Output from the shortcut menu, then enter the variable for the input or output. Enter the equation in the structure. Each equation statement must terminate with a semicolon (;). You also can use Formula Nodes for decision making. The following block diagram shows two different ways of using an if-then statement in a Formula Node. The two structures produce the same result.

LabVIEW Introduction Course Manual

4-74

ni.com

Lesson 4

Implementing a VI

The Formula Node can perform many different operations. Refer to the LabVIEW Help for more information about functions, operations, and syntax for the Formula Node. The Formula Express VI uses a calculator interface to create mathematical formulas. You can use this Express VI to perform most math functions that a basic scientific calculator can compute. Refer to the LabVIEW Help for more information about the Formula Express VI.
Note

National Instruments Corporation

4-75

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Exercise 4-7
Goal

Self-Study: Square Root VI

Create a VI that uses a Case structure to make a software decision.

Scenario
Create a VI that calculates the square root of a number the user enters. If the number is negative, display the following message to the user: Error...Negative Number.

Design Inputs and Outputs

Table 4-5. Inputs and Outputs

Type Input Output

Number

Name

Properties Double-precision, floating point; default value of 25 Double-precision, floating point

Square Root Value

Flowchart

Number

0?

No

Display Error Dialog

Yes Find Square Root of Number

Figure 4-43. Square Root VI Flowchart

LabVIEW Introduction Course Manual

4-76

ni.com

Lesson 4

Implementing a VI

Implementation
1. Open a blank VI and build the front panel shown in Figure 4-44.

Figure 4-44. Square Root VI Front Panel

2. Add a numeric control to the front panel window. Name the numeric control Number. 3. Add a numeric indicator to the front panel window. Rename the numeric indicator Square Root Value. Build the block diagram shown in Figure 4-45.

Figure 4-45. Square Root VI Block Diagram

4. Determine whether Number is greater than or equal to zero, because you cannot calculate the square root of a negative number. Add the Greater or Equal to 0? function to the right of the Number control. This function returns True if Number is greater than or equal to 0. Wire Number to the input of the Greater or Equal to 0? function. 5. If Number is less than 0, display a dialog box that informs the user of the error. Add the Case structure to the block diagram. Click the decrement or increment button to select the False case. Add a numeric constant to the False case.

National Instruments Corporation

4-77

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Right-click the numeric constant and select RepresentationDBL. Enter -99999 in the numeric constant. Wire the numeric constant to the right edge of the Case structure. Wire the new tunnel to the Square Root Value indicator. Add the One Button Dialog function to the False case. This function displays a dialog box that contains a message you specify. Right-click the message input of the One Button Dialog function and select CreateConstant from the shortcut menu. Enter Error...Negative Number in the constant. Finish wiring the False case as shown in Figure 4-45. 6. If Number is greater than or equal to 0, calculate the square root of the number. Select the True case of the Case structure. Place the Square Root function in the True case. This function returns the square root of Number. Wire the function as shown in Figure 4-46.

Figure 4-46. True Case of Square Root VI

7. Save the VI as Square Root.vi in the <Exercises>\LabVIEW Basics I\Square Root directory.

LabVIEW Introduction Course Manual

4-78

ni.com

Lesson 4

Implementing a VI

Test
1. Display the front panel. 2. Enter a positive number in the Number control. 3. Run the VI. 4. Enter a negative number in the Number control. Do not run this VI continuously. Under certain circumstances, continuously running this VI could result in an endless loop.
Caution

5. Run the VI. If Number is positive, the VI executes the True case and returns the square root of Number. If Number is negative, the VI executes the False case, returns 99999, and displays a dialog box with the message Error...Negative Number. 6. Close the VI.

End of Exercise 4-7

National Instruments Corporation

4-79

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Exercise 4-8
Goal

Self-Study: Determine Warnings VI (Challenge)

Modify an existing VI to use the Formula Node or a Case structure to make a software decision.

Scenario
In the Determine Warnings VI from Exercise 4-1, you used the Select function to pass a string based on a decision. Revise this block diagram to use either a Formula Node or a Case structure (or a combination of both) to complete the same purpose.

Design Inputs and Outputs

Table 4-6. Determine Warnings VI Inputs and Outputs

Type Numeric Control Numeric Control Numeric Control String Indicator

Name
Current Temp

Properties Double-precision, floating-point Double-precision, floating-point Double-precision, floating-point Three potential values: Heatstroke Warning, No Warning, or Freeze Warning

Max Temp

Min Temp

Warning Text

Round LED

Warning?

Flowchart
Figure 4-47 shows the flowchart you used in Exercise 4-1 to create the Determine Warnings VI.

LabVIEW Introduction Course Manual

4-80

ni.com

Lesson 4

Implementing a VI

Current Temp >=Max Temp?

No

Yes

Warning Text = Heatstroke Warning

Warning Text = No Warning

Current Temp <= Min Temp?

No

Yes

Warning Text = Freeze Warning

Pass current value of Warning Text

Warning Text = No Warning?

No

Yes

Warning ? = False

Warning ? = True

Figure 4-47. Determine Warnings VI Flowchart

National Instruments Corporation

4-81

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Implementation
As part of the challenge, no implementation instructions are given for this exercise. Start from the VI located in the <Exercises>\ LabVIEW Basics I\Determine Warnings Challenge directory. If you need assistance, open the solution VIs. The solutions are located in the <Solutions>\LabVIEW Basics I\Exercise 4-8 directory.

End of Exercise 4-8

LabVIEW Introduction Course Manual

4-82

ni.com

Lesson 4

Implementing a VI

Exercise 4-9
Goal

Self-Study: Determine More Warnings VI

Manipulate strings using String functions.

Scenario
You have a VI that determines whether a Heatstroke Warning or a Freeze Warning has occurred, based on temperature input. You must expand this VI so that it also determines whether a High Wind Warning has occurred based on a wind speed reading and a maximum wind speed setting. The warnings must be displayed as a single string. For example, if a Heatstroke Warning and a High Wind Warning has occurred, the string should read: Heatstroke and High Wind Warning.

Design Inputs and Outputs

Table 4-7. Determine More Warnings VI Inputs and Outputs

Type Numeric Control Numeric Control Numeric Control Numeric Control Numeric Control String Indicator

Name
Current Temp

Properties Double-precision, floating-point Double-precision, floating-point Double-precision, floating-point Double-precision, floating-point Double-precision, floating-point Potential values: Heatstroke Warning, Freeze Warning, Heatstroke and High Wind Warning, Freeze and High Wind Warning, High Wind Warning and No Warning Boolean

Max Temp

Min Temp

Current Wind Speed Max Wind Speed

Warning Text

Boolean Indicator

Warning?

National Instruments Corporation

4-83

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Flowchart
The flowchart shown in Figure 4-48 is used for the Determine Warnings VI. This VI does not take wind data. Modify this flowchart to determine the High Wind Warning as well.

Current Temp >=Max Temp?

No

Yes

Warning Text = Heatstroke Warning

Warning Text = No Warning

Current Temp <= Min Temp?

No

Yes

Warning Text = Freeze Warning

Pass current value of Warning Text

Warning Text = No Warning?

No

Yes

Warning ? = False

Warning ? = True

Figure 4-48. Determine Warnings VI Flowchart

LabVIEW Introduction Course Manual

4-84

ni.com

Lesson 4

Implementing a VI

The modified flowchart shown in Figure 4-49 determines the High Wind Warning in addition to the warnings already determined.

Min Temp No Max Temp Yes

No

Current Temp Min Temp >= Max Temp? Max Temp Yes Create Heatstroke String Output Upper Limit < Lower Limit and TRUE

No

Current Temp Min Temp >= Min. Temp? Max Temp Yes

No

Current Wind Min Temp >= Max Wind? Max Temp Yes

No

Create Empty String

Create Freeze String

Create Empty String

Create High Wind String

Create Empty String

Combine Strings Combine and Display Warning Text; Determine and Display Warning?

Figure 4-49. Determine More Warnings VI Flowchart

VI Architecture
There are many ways to write this VI. In this exercise, you use Case structures to determine what string to pass, and the Concatenate Strings function to merge strings together.

National Instruments Corporation

4-85

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Implementation
A portion of this VI has already been built for you. The front panel of the VI is shown in Figure 4-50. This front panel retrieves values from the user for the current temperature, the maximum temperature, the minimum temperature, the current wind speed, and the maximum wind speed and displays to the user the warning string and the warning LED. The Weather Station project in this course does not use this VI.

Figure 4-50. Determine More Warnings Front Panel

1. Open the Determine More Warnings.vi in the <Exercises>\ LabVIEW Basics I\Determine More Warnings directory. Create a block diagram similar to Figure 4-51. 2. Open the block diagram. 3. Use Figures 4-51 through 4-55 to assist you in building the block diagram code. 4. You use the following block diagram objects in this exercise: Case structure. Empty String constant. Space constant. Equal? function. Concatenate Strings function.

LabVIEW Introduction Course Manual

4-86

ni.com

Lesson 4

Implementing a VI

National Instruments Corporation

4-87

LabVIEW Introduction Course Manual

Figure 4-51. Determine More Warnings Block Diagram

Lesson 4

Implementing a VI

Figure 4-52. True Cases for When Temperature and Wind Warnings Are Not Generated

Figure 4-53. True Case for When a Temperature Warning is Generated

Figure 4-54. False Cases for When Wind and Temperature Warnings Are Generated

LabVIEW Introduction Course Manual

4-88

ni.com

Lesson 4

Implementing a VI

Figure 4-55. False Case for When a Wind Warning is Generated

5. Save the VI.

Test
1. Test the following values to be sure your VI works as expected.
Table 4-8. Weather Test Values

Name
Current Temp Max Temp Min Temp Current Wind Speed Max Wind Speed Warning Text 20 25 15 25 30

Test 1
30 25 15 25 30

Test 2
10 25 15 25 30

Test 3
30 25 15 35 30

Test 4
10 25 15 35 30

Test 5
20 25 15 35 30

Test 6

No Warning

Heatstroke Warning

Freeze Warning

Heatstroke and High Wind Warning True

Freeze and High Wind Warning True

High Wind Warning

Warning?

False

True

True

True

2. Close and save the VI when you are finished.

End of Exercise 4-9

National Instruments Corporation

4-89

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Self-Review: Quiz
1. Which of the following identifies the control or indicator on the block diagram? a. Caption b. Location c. Label d. Value 2. Which of the following structures must run at least one time? a. While Loop b. For Loop 3. Which of the following is ONLY available on the block diagram? a. Control b. Constant c. Indicator d. Connector pane 4. Which mechanical action causes a Boolean control in the False state to change to True when you click it and stay True until you release it and LabVIEW has read the value? a. Switch until released b. Switch when released c. Latch until released d. Latch when released

National Instruments Corporation

4-91

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Self-Review: Quiz Answers

1. Which of the following identifies the control or indicator on the block diagram? a. Caption b. Location c. Label d. Value 2. Which of the following structures must run at least one time? a. While Loop b. For Loop 3. Which of the following is ONLY available on the block diagram? a. Control b. Constant c. Indicator d. Connector pane 4. Which mechanical action causes a Boolean control in the False state to change to True when you click it and stay True until you release it and LabVIEW has read the value? a. Switch until released b. Switch when released c. Latch until released d. Latch when released

National Instruments Corporation

4-93

LabVIEW Introduction Course Manual

Lesson 4

Implementing a VI

Notes

LabVIEW Introduction Course Manual

4-94

ni.com

Relating Data

Sometimes it is beneficial to group data related to one another. Use arrays and clusters to group related data in LabVIEW. Arrays combine data of the same data type into one data structure, and clusters combine data of multiple data types into one data structure. Use type definitions to define custom arrays and clusters. This lesson explains arrays, clusters, and type definitions, and applications where using these can be beneficial.

Topics
A. Arrays B. Clusters C. Type Definitions

National Instruments Corporation

5-1

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

A. Arrays
An array consists of elements and dimensions. Elements are the data that make up the array. A dimension is the length, height, or depth of an array. An array can have one or more dimensions and as many as (231) 1 elements per dimension, memory permitting. You can build arrays of numeric, Boolean, path, string, waveform, and cluster data types. Consider using arrays when you work with a collection of similar data and when you perform repetitive computations. Arrays are ideal for storing data you collect from waveforms or data generated in loops, where each iteration of a loop produces one element of the array.

Restrictions
You cannot create arrays of arrays. However, you can use a multidimensional array or create an array of clusters where each cluster contains one or more arrays. Also, you cannot create an array of subpanel controls, tab controls, .NET controls, ActiveX controls, charts, or multiplot XY graphs. Refer to the Clusters section of this lesson for more information about clusters. An example of a simple array is a text array that lists the nine planets of our solar system. LabVIEW represents this as a 1D array of strings with nine elements. Array elements are ordered. An array uses an index so you can readily access any particular element. The index is zero-based, which means it is in the range 0 to n 1, where n is the number of elements in the array. For example, n = 9 for the nine planets, so the index ranges from 0 to 8. Earth is the third planet, so it has an index of 2. Figure 5-1 shows an example of an array of numerics. The first element shown in the array (3.00) is at index 1, and the second element (1.00) is at index 2. The element at index 0 is not shown in this image, because element 1 is selected in the index display. The element selected in the index display always refers to the element shown in the upper left corner of the element display.

Index Display

Element Display

Figure 5-1. Array Control of Numerics

LabVIEW Introduction Course Manual

5-2

ni.com

Lesson 5

Relating Data

Creating Array Controls and Indicators

Create an array control or indicator on the front panel by placing an array shell on the front panel, as shown in the following figure, and dragging a data object or element, which can be a numeric, Boolean, string, path, refnum, or cluster control or indicator, into the array shell.

Figure 5-2. Placing a Numeric Control in an Array Shell

If you attempt to drag an invalid control or indicator, such as an XY graph, into the array shell, you are unable to place the control or indicator in the array shell. You must insert an object in the array shell before you use the array on the block diagram. Otherwise, the array terminal appears black with an empty bracket and has no data type associated with it.

Two-Dimensional Arrays
The previous examples use 1D arrays. A 2D array stores elements in a grid. It requires a column index and a row index to locate an element, both of which are zero-based. The following figure shows an 8 column by 8 row 2D array, which contains 8 8 = 64 elements.

To create a multidimensional array on the front panel, right-click the index display and select Add Dimension from the shortcut menu. You also can resize the index display until you have as many dimensions as you want.

National Instruments Corporation

5-3

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Initializing Arrays
You can initialize an array or leave it unitialized. When an array is initialized, you defined the number of elements in each dimension and the contents of each element. An uninitialized array contains a fixed number of dimensions but no elements. Figure 5-3 shows an uninitialized 2D array control. Notice that the elements are all dimmed. This indicates that the array is uninitialized.

Figure 5-3. 2D Uninitialized Array

In Figure 5-4, six elements are initialized. In a 2D array, after you initialize an element in a row, the remaining elements in that row are initialized and populated with the default value for the data type. For example, in Figure 5-4, if you enter 4 into the element in the first column, third row, the elements in the second and third column in the third row are automatically populated with a 0.

Figure 5-4. An Initialized 2D Array with Six Elements

Creating Array Constants

To create an array constant on the block diagram, select an array constant on the Functions palette, place the array shell on the block diagram, and place a string constant, numeric constant, a Boolean constant, or cluster constant in the array shell. You can use an array constant to store constant data or as a basis for comparison with another array.

Auto-Indexing Array Inputs

If you wire an array to or from a For Loop or While Loop, you can link each iteration of the loop to an element in that array by enabling auto-indexing. The tunnel image changes from a solid square to the image shown at left to indicate auto-indexing. Right-click the tunnel and select Enable Indexing or Disable Indexing from the shortcut menu to toggle the state of the tunnel.

LabVIEW Introduction Course Manual

5-4

ni.com

Lesson 5

Relating Data

Array Inputs
If you enable auto-indexing on an array wired to a For Loop input terminal, LabVIEW sets the count terminal to the array size so you do not need to wire the count terminal. Because you can use For Loops to process arrays one element at a time, LabVIEW enables auto-indexing by default for every array you wire to a For Loop. You can disable auto-indexing if you do not need to process arrays one element at a time. In Figure 5-5, the For Loop executes a number of times equal to the number of elements in the array. Normally, if the count terminal of the For Loop is not wired, the run arrow is broken. However, in this case the run arrow is not broken.

Figure 5-5. Array Used to Set For Loop Count

If you enable auto-indexing for more than one tunnel or if you wire the count terminal, the actual number of iterations becomes the smaller of the choices. For example, if two auto-indexed arrays enter the loop, with 10 and 20 elements respectively, and you wire a value of 15 to the count terminal, the loop still only executes 10 times, indexing all elements of the first array but only the first 10 elements of the second array.

Array Outputs
When you auto-index an array output tunnel, the output array receives a new element from every iteration of the loop. Therefore, auto-indexed output arrays are always equal in size to the number of iterations.

National Instruments Corporation

5-5

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

The wire from the output tunnel to the array indicator becomes thicker as it changes to an array at the loop border, and the output tunnel contains square brackets representing an array, as shown Figure 5-6.

Figure 5-6. Auto-Indexed Output

Right-click the tunnel at the loop border and select Enable Indexing or Disable Indexing from the shortcut menu to enable or disable auto-indexing. Auto-indexing for While Loops is disabled by default. For example, disable auto-indexing if you need only the last value passed out of the tunnel.

Creating Two-Dimensional Arrays

You can use two For Loops, nested one inside the other, to create a 2D array. The outer For Loop creates the row elements, and the inner For Loop creates the column elements, as shown in Figure 5-7.

Figure 5-7. Creating a 2D Array

LabVIEW Introduction Course Manual

5-6

ni.com

Lesson 5

Relating Data

Exercise 5-1
Goal

Concept: Manipulating Arrays

Manipulate arrays using various LabVIEW functions.

Description
You are given a VI and asked to enhance it for a variety of purposes. For each part of this exercise, begin with the Array Investigation.vi located in the <Exercises>\LabVIEW Basics I\Manipulating Arrays directory. The front panel of this VI is shown in Figure 5-8.

Figure 5-8. Array Investigation VI Front Panel

Figure 5-9 shows the block diagram of this VI.

Figure 5-9. Array Investigation VI Block Diagram

This exercise is divided into parts. You are given the scenario for each part first. Refer to the end of this exercise for detailed implementation instructions for each part.

Part 1: Iterate, Modify, and Graph Array

Modify the Array Investigation VI so that after the array is created, the array is indexed into For Loops where you multiply each element of the array by 100 and coerce each element to the nearest whole number. Graph the resulting 2D array to an intensity graph.

National Instruments Corporation

5-7

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Part 2: Simplified Iterate, Modify, and Graph Array

Modify the Array Investigation VI or the solution from Part 1 to accomplish the same goals without using the nested For Loops.

Part 3: Create Subset Arrays

Modify the Array Investigation VI so that the VI creates a new array that contains the contents of the third row, and another new array that contains the contents of the second column.

Part 1: Implementation
Modify the Array Investigation VI so that after the array is created, the array is indexed into For Loops where you multiply each element of the array by 100 and coerce each element to the nearest whole number. Graph the resulting 2D array on an intensity graph. 1. Open Array Investigation.vi located in the <Exercises>\ LabVIEW Basics I\Manipulating Arrays directory. 2. Save the VI as Array Investigation Part 1.vi. 3. Add an intensity graph to the front panel of the VI and autoscale the X and Y axes, as shown in Figure 5-10. To autoscale the axes, right-click the intensity graph and select X ScaleAutoScale X and Y Scale AutoScale Y.

LabVIEW Introduction Course Manual

5-8

ni.com

Lesson 5

Relating Data

Figure 5-10. Array Investigation Part 1 VI Front Panel

4. Open the block diagram of the VI. In the following steps, you create a block diagram similar to Figure 5-11.

Figure 5-11. Array Investigation Part 1 VI Block Diagram

5. Iterate the Array. Add a For Loop to the right of the existing code. Add a second For Loop inside the first For Loop. Wire the array indicator terminal to the interior For Loop border. This creates an auto-indexed input tunnel on both For Loops.

National Instruments Corporation

5-9

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

6. Multiply each element of the array by 100. Add a Multiply function to the interior For Loop. Wire the indexed input tunnel to the x input of the Multiply function. Right-click the y input and select CreateConstant from the shortcut menu. Enter 100 in the constant. 7. Round each element to the nearest whole number. Add a Round To Nearest function to the right of the Multiple function. Wire the output of the Multiply function to the input of the Round To Nearest function. 8. Create a 2D array on the output of the For Loops to recreate the modified array. Wire the output of the Round To Nearest function to the outer For Loop. This creates an auto-indexed output tunnel on both For Loops. 9. Wire the output array to the Intensity Graph indicator. 10. Switch to the front panel. 11. Save the VI. 12. Enter values for Rows and Columns. 13. Run the VI.

Part 2: Implementation
Modify Part 1 to accomplish the same goals without using the nested For Loops. 1. Open Array Investigation Part 1.vi if it is not still open. 2. Save the VI as Array Investigation Part 2.vi. 3. Open the block diagram. 4. Right-click the border of the interior For Loop, containing the Multiply function and the Round to Nearest function, and select Remove For Loop.

LabVIEW Introduction Course Manual

5-10

ni.com

Lesson 5

Relating Data

5. Right-click the border of the remaining For Loop and select Remove For Loop from the shortcut menu. Your block diagram should resemble Figure 5-12.

Figure 5-12. Array Investigation Part 2 VI Block Diagram

6. Save the VI. 7. Switch to the front panel. 8. Enter values for Rows and Columns. 9. Run the VI. Notice that the VI behaves the same as the solution for Part 1. This is because mathematical functions are polymorphic. For example, because the x input of the Multiply function is a two-dimensional array, and the y input is a scalar, the Multiply function multiplies each element in the array by the scalar, and outputs an array of the same dimension as the x input.

Part 3: Implementation
Modify Array Investigation VI so that the VI creates a new array that contains the contents of the third row, and another new array that contains the contents of the second column. 1. Open Array Investigation.vi located in the <Exercises>\ LabVIEW Basics I\Manipulating Arrays directory. 2. Save the VI as Array Investigation Part 3.vi. 3. Open the block diagram of the VI.

National Instruments Corporation

5-11

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

In the following steps, you build a block diagram similar to that shown in Figure 5-13.

Figure 5-13. Array Investigation Part 3 VI Block Diagram

4. Retrieve the third row of data from Array using the Index Array function. Add the Index Array function to the block diagram. Wire Array to the array input of the Index Array function. The Index Array function accepts an n-dimensional array. After you wire the input array to the Index Array function, the input and output terminal names change to match the dimension of the array wired. Therefore, wire the input array to the Index Array function before wiring any other terminals.
Tip

Right-click the index(row) input of the Index Array function. Select CreateConstant from the shortcut menu. Enter 2 in the constant to retrieve the third row. Remember that the index begins at zero. Right-click the subarray output of the Index Array function. Select CreateIndicator from the shortcut menu. Name the indicator Third Row. 5. Retrieve the second column of data from the Array using the Index Array function. Add another Index Array function to the block diagram. Wire Array to the array input of the Index Array function. Right-click the disable index(col) input of the Index Array function.

LabVIEW Introduction Course Manual

5-12

ni.com

Lesson 5

Relating Data

Select CreateConstant. Enter 1 in the constant to retrieve the second column because the index begins at zero. Right-click the subarray output of the Index Array function. Select CreateIndicator. Name the indicator Second Column. 6. Save the VI. 7. Switch to the front panel. 8. Enter values for Rows and Columns. 9. Run the VI.

End of Exercise 5-1

National Instruments Corporation

5-13

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

B. Clusters
Clusters group data elements of mixed types. An example of a cluster is the LabVIEW error cluster, which combines a Boolean value, a numeric value, and a string. A cluster is similar to a record or a struct in text-based programming languages. Bundling several data elements into clusters eliminates wire clutter on the block diagram and reduces the number of connector pane terminals that subVIs need. The connector pane has, at most, 28 terminals. If your front panel contains more than 28 controls and indicators that you want to pass to another VI, group some of them into a cluster and assign the cluster to a terminal on the connector pane. Most clusters on the block diagram have a pink wire pattern and data type terminal. Error clusters have a dark yellow wire pattern and data type terminal. Clusters of numeric values, sometimes referred to as points, have a brown wire pattern and data type terminal. You can wire brown numeric clusters to Numeric functions, such as Add or Square Root, to perform the same operation simultaneously on all elements of the cluster.

Order of Cluster Elements

Although cluster and array elements are both ordered, you must unbundle all cluster elements at once or use the Unbundle By Name function to access specific cluster elements. Clusters also differ from arrays in that they are a fixed size. Like an array, a cluster is either a control or an indicator. A cluster cannot contain a mixture of controls and indicators.

Creating Cluster Controls and Indicators

Create a cluster control or indicator on the front panel by placing a cluster shell on the front panel, as shown in the following figure, and dragging a data object or element, which can be a numeric, Boolean, string, path, refnum, array, or cluster control or indicator, into the cluster shell. Resize the cluster shell by dragging the cursor while you place the cluster shell.

Figure 5-14. Creation of a Cluster Control

LabVIEW Introduction Course Manual

5-14

ni.com

Lesson 5

Relating Data

Figure 5-15 is an example of a cluster containing three controls: a string, a Boolean switch, and a numeric. A cluster is either a control or an indicator; it cannot contain a mixture of controls and indicators.

Figure 5-15. Cluster Control Example

Creating Cluster Constants

Functions palette, place the cluster shell on the block diagram, and place a string constant, numeric constant, a Boolean constant, or cluster constant in the cluster shell. You can use a cluster constant to store constant data or as a basis for comparison with another cluster. If you have a cluster control or indicator on the front panel window and you want to create a cluster constant containing the same elements on the block diagram, you can either drag that cluster from the front panel window to the block diagram or right-click the cluster on the front panel window and select CreateConstant from the shortcut menu.

Cluster Order
Cluster elements have a logical order unrelated to their position in the shell. The first object you place in the cluster is element 0, the second is element 1, and so on. If you delete an element, the order adjusts automatically. The cluster order determines the order in which the elements appear as terminals on the Bundle and Unbundle functions on the block diagram. You can view and modify the cluster order by right-clicking the cluster border and selecting Reorder Controls In Cluster from the shortcut menu.

National Instruments Corporation

5-15

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

The toolbar and cluster change, as shown in Figure 5-16.

1 3

1 2

Confirm Button Cancel Button

3 4

Cluster Order Cursor Current Order

New Order

Figure 5-16. Reordering a Cluster

The white box on each element shows its current place in the cluster order. The black box shows the new place in the order for an element. To set the order of a cluster element, enter the new order number in the Click to set to text box and click the element. The cluster order of the element changes, and the cluster order of other elements adjusts. Save the changes by clicking the Confirm button on the toolbar. Revert to the original order by clicking the Cancel button. To wire clusters to each other, both clusters must have the same number of elements. Corresponding elements, determined by the cluster order, must have compatible data types. For example, if a double-precision floating-point numeric value in one cluster corresponds in cluster order to a string in the another cluster, the wire on the block diagram appears broken and the VI does not run. If the numeric values are different representations, LabVIEW coerces them to the same representation.

Using Cluster Functions

Use the Cluster functions to create and manipulate clusters. For example, you can perform tasks similar to the following: Extract individual data elements from a cluster. Add individual data elements to a cluster. Break a cluster out into its individual data elements.

LabVIEW Introduction Course Manual

5-16

ni.com

Lesson 5

Relating Data

Use the Bundle function to assemble a cluster, use the Bundle function and Bundle by Name function to modify a cluster, and use the Unbundle function and the Unbundle by Name function to disassemble clusters. You also can place the Bundle, Bundle by Name, Unbundle, and Unbundle by Name functions on the block diagram by right-clicking a cluster terminal on the block diagram and selecting Cluster & Variant Palette from the shortcut menu. The Bundle and Unbundle functions automatically contain the correct number of terminals. The Bundle by Name and Unbundle by Name functions appear with the first element in the cluster. Use the Positioning tool to resize the Bundle by Name and Unbundle by Name functions to show the other elements of the cluster.

Assembling Clusters
Use the Bundle function to assemble a cluster from individual elements or to change the values of individual elements in an existing cluster without having to specify new values for all elements. Use the Positioning tool to resize the function or right-click an element input and select Add Input from the shortcut menu.

Figure 5-17. Assembling a Cluster on the Block Diagram

Modifying a Cluster
If you wire the cluster input, you can wire only the elements you want to change. For example, the Input Cluster shown in Figure 5-18 contains three controls.

Figure 5-18. Bundle Used to Modify a Cluster

If you know the cluster order, you can use the Bundle function to change the Command value by wiring the elements shown in Figure 5-19.

National Instruments Corporation

5-17

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

You can also use the Bundle by Name function to replace or access labeled elements of an existing cluster. The Bundle by Name function works like the Bundle function, but instead of referencing cluster elements by their cluster order, it references them by their owned labels. You can access only elements with owned labels. The number of inputs does not need to match the number of elements in output cluster. Use the Operating tool to click an input terminal and select an element from the pull-down menu. You also can right-click the input and select the element from the Select Item shortcut menu. In Figure 5-19, you can use the Bundle by Name function to change New Command and New Function.

Figure 5-19. Bundle By Name Used to Modify a Cluster

Use the Bundle by Name function for data structures that might change during development. If you add a new element to the cluster or modify its order, you do not need to rewire the Bundle by Name function because the names are still valid.

Disassembling Clusters
Use the Unbundle function to split a cluster into its individual elements. Use the Unbundle by Name function to return the cluster elements whose names you specify. The number of output terminals does not depend on the number of elements in the input cluster. Use the Operating tool to click an output terminal and select an element from the pull-down menu. You also can right-click the output terminal and select the element from the Select Item shortcut menu. For example, if you use the Unbundle function with the following cluster, it has four output terminals that correspond to the four controls in the cluster. You must know the cluster order so you can associate the correct Boolean terminal of the unbundled cluster with the corresponding switch in the cluster. In this example, the elements are ordered from top to bottom starting with element 0. If you use the Unbundle by Name function, you can have an arbitrary number of output terminals and access individual elements by name in any order.

LabVIEW Introduction Course Manual

5-18

ni.com

Lesson 5

Relating Data

Figure 5-20. Unbundle and Unbundle By Name

Error Clusters
LabVIEW contains a custom cluster called the error cluster. LabVIEW uses error clusters to pass error information. An error cluster contains the following elements: statusBoolean value that reports TRUE if an error occurred. code32-bit signed integer that identifies the error numerically. sourceString that identifies where the error occurred.

Refer to Lesson 3, Troubleshooting and Debugging VIs, for more information about using error clusters. Refer to the Handling Errors topic of the LabVIEW Help for more information about using error clusters.

National Instruments Corporation

5-19

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Exercise 5-2
Goal

Concept: Clusters
Create clusters on the front panel window, reorder clusters, and use the cluster functions to assemble and disassemble clusters.

Description
In this exercise, follow the instructions to experiment with clusters, cluster order, and cluster functions. The VI you create has no practical applications, but is useful for understanding cluster concepts. 1. Open a blank VI. 2. Save the VI as Cluster Experiment.vi in the <Exercises>\ LabVIEW Basics I\Clusters directory. In the following steps, you create a front panel similar to Figure 5-21.

Figure 5-21. Cluster Experiment VI Front Panel

3. Add a stop button to the front panel window. 4. Add a numeric indicator to the front panel window. 5. Add a round LED to the front panel. 6. Rename the LED Boolean 2.

LabVIEW Introduction Course Manual

5-20

ni.com

Lesson 5

Relating Data

7. Create a cluster named Cluster, containing a numeric, two toggle switches, and a slide. Add a cluster shell to the front panel. Add a numeric control to the cluster. Add two vertical toggle switches to the cluster. Rename the Boolean toggle switches to Boolean 1. Add a horizontal fill slide to the cluster. 8. Create Modified Cluster, containing the same contents as Cluster, but indicators instead of controls. Create a copy of Cluster. Relabel the copy Modified Cluster. Right-click the shell of Modified Cluster, and select Change to Indicator from the shortcut menu. 9. Create Small Cluster, containing a Boolean indicator and a numeric indicator. Create a copy of Modified Cluster. Relabel the copy Small Cluster. Delete the second toggle switch. Delete the horizontal fill slide indicator. Right-click Small Cluster and select AutosizingSize to Fit. Relabel the numeric indicator to Slide value. Resize the cluster as needed. 10. Verify the cluster order of Cluster, Modified Cluster, and Small Cluster. Right-click the boundary of Cluster and select Reorder Controls in Cluster from the shortcut menu. Confirm the cluster order shown in Figure 5-22.

National Instruments Corporation

5-21

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Click the Confirm button on the toolbar to set the cluster order and exit the cluster order edit mode. Right-click the boundary of Modified Cluster and select Reorder Controls in Cluster from the shortcut menu. Confirm the cluster orders shown in Figure 5-22. Modified Cluster should have the same cluster order as Cluster. Click the Confirm button on the toolbar to set the cluster order and exit the cluster order edit mode. Right-click the boundary of Small Cluster and select Reorder Controls in Cluster from the shortcut menu. Click the OK button on the toolbar to set the cluster order and exit the cluster order edit mode. Confirm the cluster orders shown in Figure 5-22.

Figure 5-22. Cluster Orders

LabVIEW Introduction Course Manual

5-22

ni.com

Lesson 5

Relating Data

In the following steps, build the block diagram shown in Figure 5-23.

Figure 5-23. Cluster Experiment VI Block Diagram

11. Add the While Loop from the Structures palette to the block diagram. 12. Disassemble Cluster. Add the Unbundle function to the block diagram. Wire Cluster to the input of the Unbundle function to resize the function automatically. 13. Assemble Small Cluster. Add the Bundle function to the block diagram. Wire the Bundle function as shown in Figure 5-23. 14. Assemble Modified Cluster. Add the Unbundle by Name function to the block diagram. Wire the Cluster to the Unbundle by Name function. Resize the Unbundle by Name function to have two output terminals. Select Numeric in the first node, and Boolean 1 in the second node. If a label name is not correct, use the Operating tool to select the correct item. Add the Increment function to the block diagram.

National Instruments Corporation

5-23

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Wire the Numeric output of the Unbundle By Name function to the input of the Increment function. This function adds one to the value of Numeric. Add the Not function to the block diagram. Wire the Boolean 1 output of the Unbundle By Name function to the x input of the Not function. This function returns the logical opposite of the value of Boolean. Add the Bundle by Name function to the block diagram. Wire Cluster to the input cluster input. Resize this function to have two input terminals. Select Numeric in the first node and Boolean 1 in the second node. If a label name is not correct, use the Operating tool to select the correct item. Wire the output of the Increment function to Numeric. Wire the output of the Not function to Boolean 1. Wire the output of the Bundle By Name function to the Modified Cluster indicator. 15. Add a wait function to provide the processor with time to complete other tasks. Add the Wait Until Next ms Multiple function to the block diagram. Right-click the millisecond multiple terminal of the Wait Until Next ms Multiple function. Select CreateConstant from the shortcut menu. Enter 100 in the constant. 16. Complete the block diagram and wire the objects as shown in Figure 5-23. 17. Save the VI. 18. Display the front panel. 19. Run the VI.

LabVIEW Introduction Course Manual

5-24

ni.com

Lesson 5

Relating Data

20. Enter different values in Cluster and notice how values entered in Cluster affect the Modified Cluster and Small Cluster indicators. Is this the behavior you expected? 21. Click the Stop button when you are done. 22. Change the cluster order of Modified Cluster. Run the VI. How did the changed order affect the behavior? 23. Close the VI. Do not save changes.

End of Exercise 5-2

National Instruments Corporation

5-25

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

C. Type Definitions
You can use type definitions to define custom arrays and clusters.

Custom Controls
Use custom controls and indicators to extend the available set of front panel objects. You can create custom user interface components for an application that vary cosmetically from built-in LabVIEW controls and indicators. You can save a custom control or indicator you created in a directory or LLB and use the custom control or indicator on other front panels. You also can create an icon for the custom control or indicator and add it to the Controls palette. Refer to the Creating Custom Controls, Indicators, and Type Definitions topic of the LabVIEW Help for more information about creating and using custom controls and type definitions. Use the Control Editor window to customize controls and indicators. For example, you can change the size, color, and relative position of the elements of a control or indicator and import images into the control or indicator. You can display the Control Editor window in the following ways: Right-click a front panel control or indicator and select Advanced Customize from the shortcut menu. Use the Positioning tool to select a front panel control or indicator and select EditCustomize Control. Use the New dialog box.

The Control Editor appears with the selected front panel object in its window. The Control Editor has two modes, edit mode and customize mode. The Control Editor window toolbar indicates whether you are in edit mode

or in customize mode. The Control Editor window opens in edit mode. Click

the Edit Mode button to change to customize mode. Click the Customize Mode button to return to edit mode. You also can switch between modes by selecting OperateChange to Customize Mode or OperateChange to Edit Mode. Use edit mode to change the size or color of a control or indicator and to select options from its shortcut menu, just as you do in edit mode on a front panel.

LabVIEW Introduction Course Manual

5-26

ni.com

Lesson 5

Relating Data

Use customize mode to make extensive changes to controls or indicators by changing the individual parts of a control or indicator.

Edit Mode
In the edit mode, you can right-click the control and manipulate its settings as you would in the LabVIEW programming environment.

1 2

Edit Mode Type Definition Status

3 4

Text Align Objects

5 6

Distribute Objects Reorder Objects

Customize Mode
In the customize mode, you can move the individual components of the control around with respect to each other. For a listing of what you can manipulate in customize mode, select WindowShow Parts Window.

1 2

Customize Mode Type Definition Status

3 4

Text Align Objects

5 6

Distribute Objects Reorder Objects

One way to customize a control is to change its type definition status. You can save a control as a control, a type definition, or a strict type definition, depending on the selection visible in the Type Def. Status ring. The control option is the same as a control you would select from the Controls palette. You can modify it in any way you need to, and each copy you make and change retains its individual properties.

Saving Custom Controls

After creating a custom control, you can save it for use later. By default, controls saved on disk have a .ctl extension. You also can use the Control Editor to save controls with your own default settings. For example, you can use the Control Editor to modify the defaults of a waveform graph, save it, and later recall it in other VIs.

National Instruments Corporation

5-27

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Type Definitions
Use type definitions and strict type definitions to link all the instances of a custom control or indicator to a saved custom control or indicator file. You can make changes to all instances of the custom control or indicator by editing only the saved custom control or indicator file, which is useful if you use the same custom control or indicator in several VIs. When you place a custom control or indicator in a VI, no connection exists between the custom control or indicator you saved and the instance of the custom control or indicator in the VI. Each instance of a custom control or indicator is a separate, independent copy. Therefore, changes you make to a custom control or indicator file do not affect VIs already using that custom control or indicator. If you want to link instances of a custom control or indicator to the custom control or indicator file, save the custom control or indicator as a type definition or strict type definition. All instances of a type definition or a strict type definition link to the original file from which you created them. When you save a custom control or indicator as a type definition or strict type definition, any data type changes you make to the type definition or strict type definition affect all instances of the type definition or strict type definition in all the VIs that use it. Also, cosmetic changes you make to a strict type definition affect all instances of the strict type definition on the front panel. Type definitions identify the correct data type for each instance of a custom control or indicator. When the data type of a type definition changes, all instances of the type definition automatically update. In other words, the data type of the instances of the type definition change in each VI where the type definition is used. However, because type definitions identify only the data type, only the values that are part of the data type update. For example, on numeric controls, the data range is not part of the data type. Therefore, type definitions for numeric controls do not define the data range for the instances of the type definitions. Also, because the item names in ring controls do not define the data type, changes to ring control item names in a type definition do not change the item names in instances of the type definition. However, if you change the item names in the type definition for an enumerated type control, the instances update because the item names are part of the data type. An instance of a type definition can have its own unique caption, label, description, tip strip, default value, size, color, or style of control or indicator, such as a knob instead of a slide. If you change the data type in a type definition, LabVIEW converts the old default value in instances of the type definition to the new data type, if possible. LabVIEW cannot preserve the instance default value if the data type changes to an incompatible type, such as replacing a numeric control

LabVIEW Introduction Course Manual

5-28

ni.com

Lesson 5

Relating Data

or indicator with a string control or indicator. When the data type of a type definition changes to a data type incompatible with the previous type definition, LabVIEW sets the default value of instances to the default value for the new data type. For example, if you change a type definition from a numeric to a string type, LabVIEW replaces any default values associated with the old numeric data type with empty strings.

Strict Type Definitions

A strict type definition forces everything about an instance to be identical to the strict type definition, except the caption, label, description, tip strip, and default value. As with type definitions, the data type of a strict type definition remains the same everywhere you use the strict type definition. Strict type definitions also define other values, such as range checking on numeric controls and the item names in ring controls. The only VI Server properties available for strict type definitions are those that affect the appearance of the control or indicator, such as Visible, Disabled, Key Focus, Blinking, Position, and Bounds. You cannot prevent an instance of a strict type definition from automatically updating unless you remove the link between the instance and the strict type definition. Type definitions and strict type definitions create a custom control using a cluster of many controls. If you need to add a new control and pass a new value to every subVI, you can add the new control to the custom control cluster. This substitutes having to add the new control to the front panel of each subVI and making new wires and terminals.

National Instruments Corporation

5-29

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Exercise 5-3
Goal

Type Definition
Explore the differences between a type definition and a strict type definition.

Description
1. Open a blank VI. 2. Create a custom control with a strict type definition status. Add a numeric control to the front panel window. Right-click the control and select AdvancedCustomize from the shortcut menu. The Control Editor opens. Select Strict Type Def. from the Control Type pull-down menu. Right-click the numeric control and select Representation Unsigned Long from the shortcut menu. Select FileSave. Name the control U32 Numeric.ctl in the <Exercises>\ LabVIEW Basics I\Type Definition directory. Close the Control Editor window. Click Yes when asked if you would like to replace the original control. 3. Explore the strictly defined custom numeric. Right-click the numeric control and select Properties from the shortcut menu. Notice that the only options available are Appearance, Documentation, and Key Navigation. All other properties are defined by the strict type definition. Click Cancel to exit the Properties dialog box. Right-click the numeric control again. Notice that representation is not available on the shortcut menu. Also notice that you can open the type definition or disconnect from the type definition.

LabVIEW Introduction Course Manual

5-30

ni.com

Lesson 5

Relating Data

4. Change the type definition status to type definition. Right-click the numeric control and select Open Type Def. from the shortcut menu. Select Type Def. from the Control Type pull-down menu. Save the control. Close the Control Editor window. 5. Explore the type defined custom numeric. Right-click the numeric control and select Properties from the shortcut menu. Notice that more items are available, such as data entry, and format and precision. Click Cancel to exit the Properties dialog box. Right-click the numeric control again. Notice that Representation is dimmed on the shortcut menu because the type definition defines the data type. Also notice that you can choose whether to auto-update with the type definition. 6. Add another instance of the custom control to the front panel window and disconnect it from the type definition. Select Select a Control from the Controls palette. Select the U32 Numeric.ctl from the <Exercises>\ LabVIEW Basics I\Type Definition directory. Click OK. Right-click the new control and select Disconnect from Type Def from the shortcut menu. Right-click the control again and notice that you can now change the Representation because the numeric is no longer linked to the type definition. 7. Close the VI when you are finished. You do not need to save the VI.

End of Exercise 5-3

National Instruments Corporation

5-31

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Self-Review: Quiz
1. You can create an array of arrays. a. True b. False 2. You have two input arrays wired to a For Loop. Auto-indexing is enabled on both tunnels. One array has 10 elements, the second array has five elements. A value of 7 is wired to the Count terminal, as shown in Figure 5-24. What is the value of the Iterations indicator after running this VI?

Figure 5-24. What is the Value of the Iteration Indicator?

3. You customize a control, select Control from the Type Def. Status pull-down menu, and save the control as a .ctl file. You then use an instance of the custom control on your front panel window. If you open the .ctl file and modify the control, does the control on the front panel window change? a. Yes b. No 4. You are inputting data that represents a circle. The circle data includes an x position, a y position, and a radius. All three pieces of data are double-precision. In the future, you might need to store the color of the circle, represented as an integer. How should you represent the circle on your front panel window? a. Three separate controls for the two positions and the radius. b. A cluster containing all of the data. c. A custom control containing a cluster. d. A type definition containing a cluster. e. An array with three elements.

National Instruments Corporation

5-33

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Self-Review: Quiz Answers

1. You can create an array of arrays. a. True b. False 2. You have two input arrays wired to a For Loop. Auto-indexing is enabled on both tunnels. One array has 10 elements, the second array has five elements. A value of 7 is wired to the Count terminal, as shown in the following figure. What is the value of the Iterations indicator after running this VI?

Figure 5-25. What is the value of the Iteration indicator?

Value of Iterations = 4 LabVIEW does not exceed the array size. This helps to protect against programming error. LabVIEW mathematical functions work the same wayif you wire a 10 element array to the x input of the Add function, and a 5 element array to the y input of the Add function, the output is a 5 element array. Although the for loop runs 5 times, the iterations are zero based, therefore the value of the Iterations indicators is 4. 3. You customize a control, select Control from the Type Def. Status pull-down menu, and save the control as a .ctl file. You then use an instance of the custom control on your front panel window. If you open the .ctl file and modify the control, does the control on the front panel window change? a. Yes b. No

National Instruments Corporation

5-35

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

4. You are inputting data that represents a circle. The circle data includes an x position, a y position, and a radius. All three pieces of data are double precision. In the future, you might need to store the color of the circle, represented as an integer. How should you represent the circle on your front panel window? a. Three separate controls for the two positions and the radius. b. A cluster containing all of the data. c. A custom control containing a cluster. d. A type definition containing a cluster. e. An array with three elements.

LabVIEW Introduction Course Manual

5-36

ni.com

Lesson 5

Relating Data

Notes

National Instruments Corporation

5-37

LabVIEW Introduction Course Manual

Lesson 5

Relating Data

Notes

LabVIEW Introduction Course Manual

5-38

ni.com

Storing Measurement Data

You have learned how to acquire data and how to display it, but storage of your data is usually a very important part of any project. In this lesson, you learn about storing data.

Topics
A. Understanding File I/O B. Understanding High-Level File I/O C. Understanding Low-Level File I/O

National Instruments Corporation

6-1

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

A. Understanding File I/O

File I/O writes data to or reads data from a file. A typical file I/O operation involves the following process. 1. You create or open a file. After the file opens, a unique identifier called a refnum represents the file. Refer to the Building the Front Panel topic of the LabVIEW Help for more information about refnums. 2. The File I/O VI or function reads from or writes to the file. 3. You close the file.

1 2

Open File Read/Write File

3 4

Close File Check for Errors

Figure 6-1. Steps in a Typical File I/O Operation

File Formats
LabVIEW can use or create the following file formats: Binary, ASCII, LVM, and TDMS. BinaryBinary files are the underlying file format of all other file formats. ASCIIAn ASCII file is a specific type of binary file that is a standard used by most programs. It consists of a series of ASCII codes. ASCII files are also called text files. LVMThe LabVIEW measurement data file (.lvm) is a tab-delimited text file you can open with a spreadsheet application or a text-editing application. The .lvm file includes information about the data, such as the date and time the data was generated. This file format is a specific type of ASCII file created for LabVIEW. TDMSThis file format is a specific type of binary file created for National Instruments products. It actually consists of two separate filesa binary file that contains data and stores properties about the data, and a binary index file that provides consolidated information on all the attributes and pointers in the binary file.

LabVIEW Introduction Course Manual

6-2

ni.com

Lesson 6

Storing Measurement Data

In this course, you learn about creating text (ASCII) files. Use text files when you want to access the file from another application, if disk space and file I/O speed are not crucial, if you do not need to perform random access read or writes, and if numeric precision is not important. You used an LVM file in Lesson 2, Navigating LabVIEW. To learn more about binary and TDMS files, refer to the LabVIEW Help or the LabVIEW Basics II: Development course.

LabVIEW Data Directory

You can use the default LabVIEW Data directory to store the data files LabVIEW generates, such as .lvm or .txt files. LabVIEW installs the LabVIEW Data directory in the default file directory for your operating system to help you organize and locate the data files LabVIEW generates. By default, the Write LabVIEW Measurement File Express VI stores the .lvm files it generates in this directory, and the Read LabVIEW Measurement File Express VI reads from this directory. The Default Data Directory constant and the Default Data Directory property also return the LabVIEW Data directory by default. Select ToolsOptions and select Paths from the Category list to specify a different default data directory. The default data directory differs from the default directory, which is the directory you specify for new VIs, custom controls, VI templates, or other LabVIEW documents you create.

National Instruments Corporation

6-3

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

B. Understanding High-Level File I/O

Some File I/O VIs perform all three steps of a file I/O processopen, read/write, and close. If a VI performs all three steps, it is referred to as a high-level VI. However, these VIs may not be as efficient as the low-level VIs and functions designed for individual parts of the process. If you are writing to a file in a loop, use low-level file I/O VIs. If you are writing to a file in a single operation, you can use the high-level file I/O VIs instead. LabVIEW includes the following high-level file I/O VIs: Write to Spreadsheet FileConverts a 2D or 1D array of single-precision numbers to a text string and writes the string to a new ASCII file or appends the string to an existing file. You also can transpose the data. The VI opens or creates the file before writing to it and closes it afterwards. You can use this VI to create a text file readable by most spreadsheet applications. Read From Spreadsheet FileReads a specified number of lines or rows from a numeric text file beginning at a specified character offset and converts the data to a 2D single-precision array of numbers. The VI opens the file before reading from it and closes it afterwards. You can use this VI to read a spreadsheet file saved in text format. Write to Measurement FileAn Express VI that writes data to a text-based measurement file (.lvm) or a binary measurement file (.tdms) format. You can specify the save method, file format (.lvm or .tdms), header type, and delimiter. Read from Measurement FileAn Express VI that reads data from a text-based measurement file (.lvm) or a binary measurement file (.tdms) format. You can specify the file name, file format, and segment size.

Avoid placing the high-level VIs in loops, because the VIs perform open and close operations each time they run.
Tip

LabVIEW Introduction Course Manual

6-4

ni.com

Lesson 6

Storing Measurement Data

Exercise 6-1
Goal

Spreadsheet Example VI
Save a 2D array in a text file so a spreadsheet application can access the file and to explore how to display numeric data in a table.

Description
Complete the following steps to examine a VI that saves numeric arrays to a file in a format you can access with a spreadsheet. 1. Open the Spreadsheet Example VI located in the <Exercises>\ LabVIEW Basics I\Spreadsheet Example directory. The following front panel window is already built.

2. Run the VI. The VI generates a 2D array of 128 rows 3 columns. The first column contains data for a sine waveform, the second column contains data for a noise waveform, and the third column contains data for a cosine waveform. The VI plots each column in a graph and displays the data in a table. 3. When the Choose file to write dialog box appears, save the file as wave.txt in the <Exercises>\LabVIEW Basics I\ Spreadsheet Example directory and click the OK button. Later, you will examine this file. 4. Display and examine the block diagram for this VI.

National Instruments Corporation

6-5

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

The Sine Pattern VI returns a numeric array of 128 elements containing a sine pattern. The constant 90.0, in the second instance of the Sine Pattern VI, specifies the phase of the sine pattern or cosine pattern. The Uniform White Noise VI returns a numeric array of 128 elements containing a noise pattern. The Build Array function builds the following 2D array from the sine array, noise array, and cosine array. Sine Array Noise Array Cosine Array

The Transpose 2D Array function rearranges the elements of the 2D array so element [i,j] becomes element [j,i], as follows. S N C

The Write To Spreadsheet File VI formats the 2D array into a spreadsheet string and writes the string to a file. The string has the following format, where an arrow ( ) indicates a tab, and a paragraph symbol () indicates an end of line character.

LabVIEW Introduction Course Manual

6-6

ni.com

Lesson 6

Storing Measurement Data

The Number To Fractional String function converts an array of numeric values to an array of strings that the table displays. 5. Close the VI. Do not save changes. This example stores only three arrays in the file. To include more arrays, increase the number of inputs to the Build Array function.
Note

6. Open the wave.txt file using a word processor, spreadsheet application, or text editor and view its contents. Open a word processor, spreadsheet application, or text editor, such as Notepad or WordPad. Open wave.txt. The sine waveform data appear in the first column, the random waveform data appear in the second column, and the cosine waveform data appear in the third column. 7. Exit the word processor or spreadsheet application and return to LabVIEW.

End of Exercise 6-1

National Instruments Corporation

6-7

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

C. Understanding Low-Level File I/O

Low-level file I/O VIs and functions each perform only one piece of the file I/O process. For example, there is one function to open an ASCII file, one function to read an ASCII file, and one function to close an ASCII file. Use low-level functions when file I/O is occurring within a loop.

Disk Streaming with Low-Level Functions

You also can use File I/O functions for disk streaming operations, which save memory resources by reducing the number of times the function interacts with the operating system to open and close the file. Disk streaming is a technique for keeping files open while you perform multiple write operations, for example, within a loop. Wiring a path control or a constant to the Write to Text File function, the Write to Binary File function, or the Write To Spreadsheet File VI adds the overhead of opening and closing the file each time the function or VI executes. VIs can be more efficient if you avoid opening and closing the same files frequently. To avoid opening and closing the same file, you need to pass a refnum to the file into the loop. When you open a file, device, or network connection, LabVIEW creates a refnum associated with that file, device, or network connection. All operations you perform on open files, devices, or network connections use the refnums to identify each object. The examples in Figure 6-2 and Figure 6-3 show the advantages of using disk streaming. In Figure 6-2, the VI must open and close the file during each iteration of the loop. Figure 6-3 uses disk streaming to reduce the number of times the VI must interact with the operating system to open and close the file. By opening the file once before the loop begins and closing it after the loop completes, you save two file operations on each iteration of the loop.

Figure 6-2. Non-Disk Streaming Example

LabVIEW Introduction Course Manual

6-8

ni.com

Lesson 6

Storing Measurement Data

Figure 6-3. Disk Streaming Example

National Instruments Corporation

6-9

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

Exercise 6-2
Goal

Temperature Log VI
Modify a VI to create an ASCII file using disk streaming.

Description
You have been given a VI that plots the current temperature and the average of the last three temperatures. Modify the VI to log the current temperature to an ASCII file. 1. Open the Temperature Multiplot.vi located in the
<Exercises>\LabVIEW Basics I\Temperature Multiplot

directory. 2. Save the VI as Temperature Log.vi. Select FileSave As and rename the VI Temperature Log.vi in the <Exercises>\LabVIEW Basics I\Temperature Log directory. Select the Substitute Copy for Original option. Create the directory if it does not already exist. In the steps below, you modify the block diagram similar to that shown in Figure 6-4.

Figure 6-4. Temperature Log VI Block Diagram

3. Resize the While Loop to add room for the file I/O functions.

LabVIEW Introduction Course Manual

6-10

ni.com

Lesson 6

Storing Measurement Data

4. Create a file or replace an existing file for the data log. Add the Open/Create/Replace File function to the left of the While Loop. Right-click the operation input of the Open/Create/Replace File function, and select CreateConstant. Select replace or create in the enumerated constant that appears. 5. Write the temperature data to file, adding an End of Line constant to each piece of data. Add a Number to Fractional String function inside the While Loop. Add an End of Line constant inside the While Loop. Add a Concatenate Strings function inside the While Loop. Add a Write to Text File function inside the While Loop. Wire the inputs of the Write to Text File function as shown in Figure 6-4. 6. Stop the loop if an error occurs or if the user turns off the Power switch. Delete the wire connecting the Power Boolean control to the conditional terminal. Add an Exclusive Or function next to the conditional terminal. Add an Unbundle By Name function to the While Loop. Wire the conditional terminal as shown in Figure 6-4. 7. Close the file and handle any errors that may have occurred. Add a Close File function to the right of the While Loop. Add a Simple Error Handler VI to the right of the Close File function. Finishing wiring the block diagram as shown in Figure 6-4. 8. Save the VI.

National Instruments Corporation

6-11

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

9. Test the VI. Run the VI. Give the text file a name and a location. Turn the Power switch to Off after the VI has been running for a few samples. Navigate to the text file created and explore it. 10. Close the VI and text file when you have finished.

End of Exercise 6-2

LabVIEW Introduction Course Manual

6-12

ni.com

Lesson 6

Storing Measurement Data

Exercise 6-3
Goal

Self-Study: Read VCard VI

Read an ASCII file into LabVIEW.

Scenario
The business card contacts for your company are stored in the Windows Address Book. You must extract specific data from an individual business card into a LabVIEW text display.

Design Inputs and Outputs

In this VI, the output appears in a dialog box and the inputs are from a file. Therefore, there are no inputs or outputs necessary on the front panel window of this VI.

Flowchart
To understand how to design this program, you must first view the text file created by the Address Book. 1. Open WordPad from StartAll ProgramsAccessoriesWordPad. 2. Select FileOpen. 3. Navigate to the <Exercises>\LabVIEW Basics I\Read VCard directory. 4. Change the file type to All Documents. 5. Select one of the business card files in this directory. This is an example of the text file created.
Start of VCard text file

BEGIN:VCARD VERSION:2.1 N:McGillicuttey;Heather;Louise;Ms. FN:Heather Louise McGillicuttey NICKNAME:Lou ORG:National Instruments;Internal Affairs TITLE:President NOTE:I am an imaginary person.

National Instruments Corporation

6-13

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

TEL;WORK;VOICE:512-555-1212 TEL;HOME;VOICE:512-555-1212 TEL;CELL;VOICE:512-555-1212 TEL;PAGER;VOICE:512-555-1212 TEL;WORK;FAX:512-555-1212 TEL;HOME;FAX:512-555-1212 ADR;WORK:;Corner;11500 N. Mopac Expressway;Austin;Texas;78759;USA LABEL;WORK;ENCODING=QUOTED-PRINTABLE:Corner=0D=0A11500 N. Mopac Expressway=0D=0AAustin, Texas 78759=0D=0AUSA ADR;HOME:;;111 Easy Street;Austin;Texas;78759;USA LABEL;HOME;ENCODING=QUOTED-PRINTABLE:111 Easy Street=0D=0AAustin, Texas 78759=0D=0AUSA EMAIL;PREF;INTERNET:[email protected] REV:20050818T150422Z END:VCARD

End of VCard text file

Notice that the file contains the following characters: beginning and end tagsyou can use the end tag to determine when to stop reading the file end of line characters after each tag a colon between the tag and the corresponding data a semicolon separating different parts of a each data element

All of this information is useful when writing a VI meant to parse data.

LabVIEW Introduction Course Manual

6-14

ni.com

Lesson 6

Storing Measurement Data

No

Open File

Read one line of data from file

Seperate the data into two strings at the colon

End of File?

Yes

Close File

Create an array of clusters (tag and display name) for data of interest

Add string to a tag array and a data array.

Use tag name to determine index of data of interest

No

Get data from specificed index

Replace semicolons with carriage returns

End of data of interest?

Add new row to an array of display names and data

Yes

Display 2D Array of data

Figure 6-5. Read VCard VI Flowchart

This algorithm consists of two loops. One loop reads the data from the business card file, line by line. The second loop chooses which pieces of data to display, replaces each tag name with a more meaningful name, and replaces the semicolons with end of line characters. The flowchart elements in Figure 6-5 with a thicker border represent VIs that have already been built for you for this exercise.

National Instruments Corporation

6-15

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

Implementation
1. Create a business card entry in the Windows Address Book. Open the Address Book from StartAll ProgramsAccessories Address Book. Select FileNew Contact. Fill in some or all of the fields with your information or an imaginary contact. Click OK when you have finished. Select FileExportBusiness Card (vCard). Navigate to the <Exercises>\LabVIEW Basics I\ Read VCard directory. Click Save. Select FileExit to close the Windows Address Book. 2. Open a blank VI. 3. Save the VI as Read VCard.vi in the <Exercises>\LabVIEW Basics I\Read VCard directory. 4. Open the block diagram. In the following steps, you create a block diagram similar to Figure 6-6. In this block diagram, you read the vCard you just created as a 2D array of strings. The first dimension of the array contains the tags; the second dimension contains the data.

Figure 6-6. Read VCard VI Block Diagram

LabVIEW Introduction Course Manual

6-16

ni.com

Lesson 6

Storing Measurement Data

5. Open the text file. Add an Open/Create/Replace File function to the block diagram. You do not need to wire any of the inputs of this function to use the default settings. 6. Read the data from the text file. Add a While Loop from the Structures palette to the block diagram to the right of the Open/Create/Replace File function. Add a Read From Text File function inside the While Loop. Right-click the Read From Text File function and select Read Lines to read the file by line. Wire the refnum out output of the Open/Create/Replace File function to the file (use dialog) input of the Read From Text File function. Wire the error out output of the Open/Create/Replace File function to the error in input of the Read From Text File function. Add a Match Pattern function after the Read from Text File function. Wire the text output of the Read Text function to the string input of the Match Pattern function. Right-click the regular expression terminal of the Match Pattern function and select CreateConstant from the shortcut menu. Enter a colon (:) in the string constant. Wire the before substring terminal of the Match Pattern function to create an output tunnel from the While Loop. Right-click the output tunnel and select Enable Indexing from the shortcut menu. Wire the after substring terminal of the Match Pattern function to create an output tunnel from the While Loop. Right-click the output tunnel and select Enable Indexing from the shortcut menu.

National Instruments Corporation

6-17

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

7. Stop the While Loop if an error occurs or when the end of the file has been reached. Wire the error out output of the Read From Text File function to create an output tunnel on the While Loop. Right-click the tunnel and select Replace with Shift Register from the shortcut menu. Your cursor should change into a shift register, indicating that you should choose the input side of the shift register. Click the error input tunnel on the right side of the While Loop to change the input tunnel to a shift register. Add an Unbundle By Name function inside the While Loop. Wire the error out output from the Read from Text File function to the Unbundle By Name function. Add an Or function in the While Loop. Wire the status element of the error cluster to the x input of the Or function. Add an Equal? function in the While Loop. Wire the before substring output of the Match Pattern function to the y input of the Equal? function. Right-click the x input of the Equal? function. Select CreateConstant. Enter END into the String Constant. Use all capitals, as case is important. Wire the output of the Equal? function to the y input of the Or function. Wire the output of the Or function to the conditional terminal of the While Loop. 8. Close the text file. Wire the refnum out output of the Read From Text File function to create an output tunnel on the While Loop.

LabVIEW Introduction Course Manual

6-18

ni.com

Lesson 6

Storing Measurement Data

Right-click the tunnel and select Replace with Shift Register. Your cursor should change into a shift register, indicating that you should choose the input side of the shift register. Click the left refnum input tunnel of the While Loop to replace the tunnel with a shift register. Add a Close File input to the right of the While Loop. Wire the refnum output tunnel to the refnum input input of the Close File function. Wire the error output tunnel to the error in input of the Close File function. 9. Display the arrays generated on the output of the While Loop. Right-click the substring indexed output tunnel and select Create Indicator from the shortcut menu. Name the array indicators Tags. Right-click the bottom array output tunnel and select Create Indicator from the shortcut menu. Name the array indicators Data. 10. Check for errors. Add a Simple Error Handler VI to the right of the Close File function. Wire the error out output from the Close File function to the error in input of the Simple Error Handler VI. 11. Save the VI. 12. Open the front panel window. 13. Expand the indicators to show multiple elements of the arrays. 14. Run the VI. 15. Select the VCard File when the dialog box opens.

National Instruments Corporation

6-19

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

Figure 6-7 shows an example of the front panel after running this VI. Notice that it is very similar to opening the text file. The names used for each category are not very clear. In the rest of this exercise, you modify the VI so that it parses the data for you, making it more legible to a user.

Figure 6-7. Read VCard VI Front Panel without Data Parsing

In the following steps, you add to the block diagram to parse the data in the arrays. To simplify this process, two VIs have already been built for you. One of these VIs creates an array where each array element is a cluster containing a tag and a replacement name for the tag. The second VI opens a dialog box that displays the final data in a table. 16. Switch to the block diagram. 17. Delete the tag and data array indicators. 18. Delete the wire connecting the Close File function to the Simple Error Handler.

LabVIEW Introduction Course Manual

6-20

ni.com

Lesson 6

Storing Measurement Data

National Instruments Corporation

6-21

LabVIEW Introduction Course Manual

Figure 6-8. Read VCard VI Block Diagram

Lesson 6

Storing Measurement Data

19. Move the Simple Error Handler out of the way. You use this VI later in this exercise. 20. Access the array of tags and replacement names. Place the Vcard Tags VI to the right of the Close File function. This VI is located in the <Exercises>\LabVIEW Basics I\ Read VCard directory.
Tip Use the Select a VI category of the Functions palette to locate a VI that is not part of the Functions palette. After you have placed the VI on the block diagram, you can double-click the VI to open it and examine its block diagram.

Wire the error out output of the Close File function to the error in input of the Vcard Tags VI. 21. Create a 2D array containing the replacement names and the corresponding data. Add a For Loop to the right of the Vcard Tags VI. Wire the Array terminal from the Vcard Tags VI to create an input tunnel on the For Loop. Notice that indexing has automatically been enabled. Add an Unbundle by Name function inside the For Loop. Wire the indexed input tunnel to the Unbundle by Name function. Expand the Unbundle by Name function to show two elements. Add a Search 1D Array function to the right of the Unbundle by Name function. Wire the Field Tag element of the Unbundle by Name function to the element input of the Search 1D Array function. Wire the tag array to the 1D array input of the Search 1D Array function. The tag array is the top indexed output tunnel of the While Loop. Disable indexing on the For Loop tag array input tunnel. Add an Index Array function to the right of the Search 1D Array function.

LabVIEW Introduction Course Manual

6-22

ni.com

Lesson 6

Storing Measurement Data

Wire the data array to the array terminal of the Index Array function. The data array is the bottom indexed output tunnel of the While Loop. Disable indexing on the For Loop data array input tunnel. Wire the index of element output from the Search 1D Array function to the index input of the Index Array function. Add a Search and Replace String function to the right of the Index Array function. Wire the element output of the Index Array to the input string input of the Search and Replace String function. Right-click the search string terminal of the Search and Replace String function and select CreateConstant. Enter a semicolon (;) in the string constant. Place an End of Line constant below the string constant. Wire the End of Line Constant to the replace string input of the Search and Replace String function. Right-click the replace all?(F) input of the Search and Replace String function and select CreateConstant from the shortcut menu. Use the Operating tool to change the constant to True. Add a Trim Whitespace VI to the right of the Search and Replace String function. Wire the result string output for the Search and Replace String function to the input of the Trim Whitespace VI. Add a Build Array function to the right of the Trim Whitespace VI. Resize the Build Array function to have two nodes. Wire the Field Name element of the Unbundle by Name function to the top node of the Build Array function. Wire the trimmed string output of the Trim Whitespace VI to the bottom node of the Build Array function. You now have a 2D array with meaningful descriptions in the first dimension and corresponding data in the second dimension.

National Instruments Corporation

6-23

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

22. Display the generated array. Wire the output of the Build Array function to create an output tunnel on the For Loop. Confirm that the output tunnel is auto-indexed. Place the Table Dialog VI, located in the <Exercises>\ LabVIEW Basics I\Read VCard directory, to the right of the For Loop. Wire the indexed output tunnel to the Contact Information input of the Table Dialog VI. Wire the error cluster from the Vcard Tags VI to the Table Dialog VI. Replace the error cluster tunnels with shift registers. Move the Simple Error Handler VI to the right of the Table Dialog VI. Wire the error out terminal of the Table Dialog VI to the error in terminal of the Simple Error Handler VI. 23. Switch to the front panel window. 24. Save the VI.

Test
1. Run the VI. 2. When prompted, navigate to the business card file you created earlier in this exercise. 3. Close the Table Dialog window to stop the VI. 4. Close the VI when you have finished.

End of Exercise 6-3

LabVIEW Introduction Course Manual

6-24

ni.com

Lesson 6

Storing Measurement Data

Self-Review: Quiz
1. Your continuously running test program logs to a single file the results of all tests that occur in one hour as they are calculated. If you are concerned about the execution speed of your program, should you use low-level or high-level File I/O VIs? a. Low-level file I/O VIs b. High-level file I/O VIs 2. If you want to view data in a text editor such as Notepad, what file format should you use to save the data? a. ASCII b. TDMS

National Instruments Corporation

6-25

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

Self-Review: Quiz Answers

1. Your continuously running test program logs to a single file the results of all tests that occur in one hour as they are calculated. If you are concerned about the execution speed of your program, should you use low-level or high-level File I/O VIs? a. Low-level file I/O VIs b. High-level file I/O VIs 2. If you want to view data in a text editor such as Notepad, what file format should you use to save the data? a. ASCII b. TDMS

National Instruments Corporation

6-27

LabVIEW Introduction Course Manual

Lesson 6

Storing Measurement Data

Notes

LabVIEW Introduction Course Manual

6-28

ni.com

Developing Modular Applications

This lesson describes how to develop modular applications. The power of LabVIEW lies in the hierarchical nature of the VI. After you create a VI, you can use it on the block diagram of another VI. There is no limit on the number of layers in the hierarchy. Using modular programming helps you manage changes and debug the block diagram quickly.

Topics
A. Understanding Modularity B. Building the Icon and Connector Pane C. Using SubVIs

National Instruments Corporation

7-1

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

A. Understanding Modularity
Modularity defines the degree to which a program is composed of discrete modules such that a change to one module has minimal impact on other modules. Modules in LabVIEW are called subVIs. A VI within another VI is called a subVI. A subVI corresponds to a subroutine in text-based programming languages. When you double-click a subVI, a front panel and block diagram appear, rather than a dialog box in which you can configure options. The front panel includes controls and indicators. The block diagram includes wires, front panel icons, functions, possibly subVIs, and other LabVIEW objects that also might look familiar. The upper right corner of the front panel window and block diagram window displays the icon for the VI. This icon is the same as the icon that appears when you place the VI on the block diagram. As you create VIs, you might find that you perform a certain operation frequently. Consider using subVIs or loops to perform that operation repetitively. For example, the following block diagram contains two identical operations.

Figure 7-1. Block Diagram with Two Identical Operations

LabVIEW Introduction Course Manual

7-2

ni.com

Lesson 7

Developing Modular Applications

Figure 7-2. Block Diagram with SubVIs for Identical Operations

The example calls the Temperature VI as a subVI twice on its block diagram and functions the same as the previous block diagram. You also can reuse the subVI in other VIs. The following pseudo-code and block diagrams demonstrate the analogy between subVIs and subroutines. Function Code
function average (in1, in2, out) { out = (in1 + in2)/2.0; }

Calling Program Code

main { average (point1, point2, pointavg) }

SubVI Block Diagram

Calling VI Block Diagram

B. Building the Icon and Connector Pane

After you build a VI front panel and block diagram, build the icon and the connector pane so you can use the VI as a subVI. The icon and connector pane correspond to the function prototype in text-based programming languages. Every VI displays an icon, such as the one shown as follows, in the upper right corner of the front panel and block diagram windows.

National Instruments Corporation

7-3

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

A VI icon is a graphical representation of a VI that appears on the block diagram and the Functions palette. It can contain text, images, or a combination of both. If you use a VI as a subVI, the icon identifies the subVI on the block diagram of the VI. You can double-click the icon to customize or edit it. Customizing the icon is recommended, but optional. Using the default LabVIEW icon does not affect functionality.
Note

You also need to build a connector pane, shown as follows, to use the VI as a subVI.

The connector pane is a set of terminals that correspond to the controls and indicators of that VI, similar to the parameter list of a function call in text-based programming languages. The connector pane defines the inputs and outputs you can wire to the VI so you can use it as a subVI. A connector pane receives data at its input terminals and passes the data to the block diagram code through the front panel controls and receives the results at its output terminals from the front panel indicators.

Creating an Icon
The default icon contains a number that indicates how many new VIs you have opened since launching LabVIEW. Create custom icons to replace the default icon by right-clicking the icon in the upper right corner of the front panel or block diagram and selecting Edit Icon from the shortcut menu or by double-clicking the icon in the upper right corner of the front panel. You also can drag a graphic from anywhere in your file system and drop it in the upper right corner of the front panel or block diagram. LabVIEW converts the graphic to a 32 32 pixel icon. Refer to the National Instruments Web site at ni.com/info and enter the info code expnr7 for standard graphics to use in a VI icon. Depending on the type of monitor you use, you can design a separate icon for monochrome, 16-color, and 256-color mode. LabVIEW uses the monochrome icon for printing unless you have a color printer. Use the tools on the left side of the Icon Editor dialog box to create the icon design in the editing area. The normal size image of the icon appears in the appropriate box to the right of the editing area, as shown in Figure 7-3.

LabVIEW Introduction Course Manual

7-4

ni.com

Lesson 7

Developing Modular Applications

Figure 7-3. Icon Editor Window

Use the Edit menu to cut, copy, and paste images from and to the icon. When you select a portion of the icon and paste an image, LabVIEW resizes the image to fit into the selection area. You also can drag a graphic from anywhere in your file system and drop it in the upper right corner of the front panel window or block diagram window. LabVIEW converts the graphic to a 32 32 pixel icon. Use the Copy from option on the right side of the Icon Editor dialog box to copy from a color icon to a black-and-white icon and vice versa. After you select a Copy from option, click the OK button to complete the change.
Note If you do not draw a complete border around a VI icon, the icon background appears transparent. When you select the icon on the block diagram, a selection marquee appears around each individual graphic element in the icon.

Use the Icon Editor tools to perform the following tasks: Use the Pencil tool to draw and erase pixel by pixel. Use the Line tool to draw straight lines. To draw horizontal, vertical, and diagonal lines, press the <Shift> key while you use this tool to drag the cursor. Use the Color Copy tool to copy the foreground color from an element in the icon. Use the Fill tool to fill an outlined area with the foreground color. Use the Rectangle tool to draw a rectangular border in the foreground color. Double-click this tool to frame the icon in the foreground color.

National Instruments Corporation

7-5

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

Use the Filled Rectangle tool to draw a rectangle with a foreground color frame and filled with the background color. Double-click this tool to frame the icon in the foreground color and fill it with the background color. Use the Select tool to select an area of the icon to cut, copy, move, or make other changes. Double-click this tool and press the <Delete> key to delete the entire icon. Use the Text tool to enter text into the icon. Double-click this tool to select a different font. The Small Fonts option works well in icons. Use the Foreground/Background tool to display the current foreground and background colors. Click each rectangle to display a color palette from which you can select new colors. The upper left rectangle indicates the foreground color, the lower right rectangle indicates the background color. Use the options on the right side of the editing area to perform the following tasks: Show TerminalsDisplays the terminal pattern of the connector pane OKSaves the drawing as the icon and returns to the front panel window CancelReturns to the front panel window without saving any changes

The menu bar in the Icon Editor dialog box contains more editing options under the Edit menu such as Undo, Redo, Cut, Copy, Paste, and Clear.

Setting up the Connector Pane

Define connections by assigning a front panel control or indicator to each of the connector pane terminals. To define a connector pane, right-click the icon in the upper right corner of the front panel and select Show Connector from the shortcut menu to display the connector pane. The connector pane appears in place of the icon. When you view the connector pane for the first time, you see a connector pattern. You can select a different pattern by right-clicking the connector pane and selecting Patterns from the shortcut menu. Each rectangle on the connector pane represents a terminal. Use the rectangles to assign inputs and outputs. The default connector pane pattern is 4 2 2 4. If you anticipate changes to the VI that would require a new input or output, keep the default connector pane pattern to leave extra terminals unassigned. The following front panel has four controls and one indicator, so LabVIEW displays four input terminals and one output terminal on the connector pane.

LabVIEW Introduction Course Manual

7-6

ni.com

Lesson 7

Developing Modular Applications

Figure 7-4. Slope VI Front Panel

Selecting and Modifying Terminal Patterns

Select a different terminal pattern for a VI by right-clicking the connector pane and selecting Patterns from the shortcut menu. For example, you can select a connector pane pattern with extra terminals. You can leave the extra terminals unconnected until you need them. This flexibility enables you to make changes with minimal effect on the hierarchy of the VIs. You also can have more front panel controls or indicators than terminals. A solid border highlights the pattern currently associated with the icon. You can assign up to 28 terminals to a connector pane. The most commonly used pattern is shown at left. This pattern is used as a standard to assist in simplifying wiring. Figure 7-5 shows an example of the standard layout used for terminal patterns. The top inputs and outputs are commonly used for passing references and the bottom inputs and outputs are used for error handling.

Figure 7-5. Example Terminal Pattern Layout Note

Assigning more than 16 terminals to a VI can reduce readability and usability.

National Instruments Corporation

7-7

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

Assigning Terminals to Controls and Indicators

After you select a pattern to use for the connector pane, you must assign a front panel control or indicator to each of the connector pane terminals. When you link controls and indicators to the connector pane, place inputs on the left and outputs on the right to prevent complicated, unclear wiring patterns in your VIs. To assign a terminal to a front panel control or indicator, click a terminal of the connector pane, then click the front panel control or indicator you want to assign to that terminal. Click an open space on the front panel. The terminal changes to the data type color of the control to indicate that you connected the terminal. You also can select the control or indicator first and then select the terminal.
Note Although you use the Wiring tool to assign terminals on the connector pane to front panel controls and indicators, no wires are drawn between the connector pane and these controls and indicators.

LabVIEW Introduction Course Manual

7-8

ni.com

Lesson 7

Developing Modular Applications

C. Using SubVIs
To place a subVI on the block diagram, click the Select a VI button on the Functions palette. Navigate to the VI you want to use as a subVI and double-click to place it on the block diagram. You also can place an open VI on the block diagram of another open VI. Use the Positioning tool to click the icon in the upper right corner of the front panel or block diagram of the VI you want to use as a subVI and drag the icon to the block diagram of the other VI.

Opening and Editing SubVIs

To display the front panel of a subVI from the calling VI, use the Operating or Positioning tool to double-click the subVI on the block diagram. To display the block diagram of a subVI from the calling VI, press the <Ctrl> key and use the Operating or Positioning tool to double-click the subVI on the block diagram. You can edit a subVI by using the Operating or Positioning tool to double-click the subVI on the block diagram. When you save the subVI, the changes affect all calls to the subVI, not just the current instance.

Setting Required, Recommended, and Optional Inputs and Outputs

In the Context Help window, the labels of required terminals appear bold, recommended terminals appear as plain text, and optional terminals appear dimmed. The labels of optional terminals do not appear if you click the Hide Optional Terminals and Full Path button, shown as follows, in the Context Help window.

You can designate which inputs and outputs are required, recommended, and optional to prevent users from forgetting to wire subVI terminals. Right-click a terminal in the connector pane and select This Connection Is from the shortcut menu. A checkmark indicates the terminal setting. Select Required, Recommended, or Optional. You also can select Tools OptionsFront Panel and put a checkmark in the Connector pane terminals default to required checkbox. This option sets terminals on the connector pane to Required instead of Recommended. This applies to connections made using the wiring tool and to subVIs created using Create SubVI. You can select Dynamic Dispatch Input (Required) or Dynamic Dispatch Output (Recommended) for dynamic dispatch member VIs.
Note

National Instruments Corporation

7-9

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

For terminal inputs, required means that the block diagram on which you placed the subVI will be broken if you do not wire the required inputs. Required is not available for terminal outputs. For terminal inputs and outputs, recommended or optional means that the block diagram on which you placed the subVI can execute if you do not wire the recommended or optional terminals. If you do not wire the terminals, the VI does not generate any warnings. Inputs and outputs of VIs in vi.lib are already marked as Required, Recommended, or Optional. LabVIEW sets inputs and outputs of VIs you create to Recommended by default. Set a terminal setting to required only if the VI must have the input or output to run properly.

Creating a SubVI from an Existing VI

You can simplify the block diagram of a VI by converting sections of the block diagram into subVIs. Convert a section of a VI into a subVI by using the Positioning tool to select the section of the block diagram you want to reuse and selecting EditCreate SubVI. An icon for the new subVI replaces the selected section of the block diagram. LabVIEW creates controls and indicators for the new subVI, automatically configures the connector pane based on the number of control and indicator terminals you selected, and wires the subVI to the existing wires. Figure 7-6 shows how to convert a selection into a subVI.

Figure 7-6. Creating a New SubVI

The new subVI uses a default pattern for the connector pane and a default icon. Double-click the subVI to edit the connector pane and icon, and to save the subVI.
Note Do not select more than 28 objects to create a subVI because 28 is the maximum number of connections on a connector pane. If your front panel contains more than 28 controls and indicators that you want to use programmatically, group some of them into a cluster and assign the cluster to a terminal on the connector pane.

LabVIEW Introduction Course Manual

7-10

ni.com

Lesson 7

Developing Modular Applications

Exercise 7-1
Goal

Determine Warnings VI
Create the icon and connector pane for a VI so that you can use the VI as a subVI.

Scenario
You have created a VI that determines a warning string based on the inputs given. Create an icon and a connector pane so that you can use this VI as a subVI.

Design
The subVI contains the following inputs and outputs:
Table 7-1. Determine Warnings SubVI Inputs and Outputs

Inputs Current Temp Max Temp Min Temp

Outputs Warning Text Warning?

Use the standard connector pane to assure room for future expansion. Add error clusters to the VI so that the code runs if there is no error, but does not run if there is an error.

Implementation
1. Open the Determine Warnings VI in the <Exercises>\LabVIEW Basics I\Determine Warnings directory. 2. Add an error input cluster and an error output cluster to the VI. Add an Error In 3D.ctl to the front panel. Add an Error Out 3D.ctl to the front panel. 3. Select a connector pane pattern for the VI. Right-click the icon in the upper-right corner of the window and select Show Connector from the shortcut menu. Right-click the connector pane in the upper-right corner of the window, select Patterns, from the shortcut menu, and choose the pattern shown at left.
National Instruments Corporation 7-11 LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

4. Connect the inputs and outputs to the connector as shown in Figure 7-7.

Connections

Connector Pane

Figure 7-7. Connector Pane Connections for Determine Warnings VI

Using the wiring tool, click the upper-left terminal of the connector pane. Click the corresponding front panel control, Current Temp. Notice that the connector pane terminal fills in with a color to match the data type of the control connected to it. Click the next terminal in the connector pane. Click the corresponding front panel control, Max Temp. Continue wiring the connector pane until all controls and indicators are wired, and the Context Help window matches that shown in Figure 7-7. 5. Create an icon. Right-click the connector pane and select Edit Icon. The Icon Editor window opens. Use the tools in the Icon Editor window to create an icon. Make the icon as simple or as complex as you want, however, it should be representative of the function of the VI. Figure 7-8 shows a simple example of an icon for this VI.

LabVIEW Introduction Course Manual

7-12

ni.com

Lesson 7

Developing Modular Applications

Figure 7-8. Sample Warning Icon

Click OK when you are finished to close the Icon Editor window.
Tip Double-click the selection tool to select the existing graphic. Press the <Delete> key to delete the graphic. Then, double-click the rectangle tool to automatically create a border for the icon.

Double-click the text tool to modify fonts. You can select Small Fonts to choose fonts smaller than 9 points in size.
Tip

6. Right-click the connector pane and select Show Icon from the shortcut menu to return to Icon view. 7. Save the VI. 8. Switch to the block diagram. 9. Set the VI to execute if no error occurs, and not execute if an error occurs. Surround the block diagram code with a Case structure as shown in Figure 7-9. Leave the Warning Text and Warning? indictors outside of the Case structure.

National Instruments Corporation

7-13

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

Figure 7-9. No Error Case of Determine Warnings VI

Wire the error in control to the case selector terminal. Confirm that the block diagram is in the No Error case. If it is not, switch to the case containing the code, right-click the Case structure and select Make this Case No Error from the shortcut menu. Wire the error cluster through the Case structure to the error out indicator as shown in Figure 7-9. Switch to the Error case. Wire the error cluster through the case to the error out tunnel. Right-click the Warning? tunnel and select CreateConstant from the shortcut menu. Use the Operating tool to change the constant to True. Right-click the Warning Text tunnel and select CreateConstant from the shortcut menu. Enter Error in the constant.

LabVIEW Introduction Course Manual

7-14

ni.com

Lesson 7

Developing Modular Applications

Confirm that you have completed the Error case as shown in Figure 7-10.

Figure 7-10. Error Case of Determine Warnings VI

If an error enters the VI, the VI outputs Error in Warning Text, and True in Warning? and passes the error out of the VI. If an error does not enter the VI, the VI operates as originally designed. 10. Save and close the VI.

Test
Use a blank VI to test the subVI. 1. Open a blank VI. 2. Open the block diagram. 3. Place the Determine Warnings subVI on the block diagram of the blank VI by selecting the Select a VI option on the Functions palette and navigating to the <Exercises>\LabVIEW Basics I\Determine Warnings directory. 4. Create controls and indicators for each item in the subVI. Right-click the Current Temp input and select CreateControl from the shortcut menu. Right-click the Max Temp input and select CreateControl from the shortcut menu.

National Instruments Corporation

7-15

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

Right-click the Min Temp input and select CreateControl from the shortcut menu. Right-click the Warning Text output and select CreateIndicator from the shortcut menu. Right-click the Warning? output and select CreateIndicator from the shortcut menu. 5. Switch to the front panel. 6. Enter test values in Current Temp, Max Temp, and Min Temp. 7. Run the VI. 8. After you have finished testing, close the test VI. You do not need to save the test VI.

End of Exercise 7-1

LabVIEW Introduction Course Manual

7-16

ni.com

Lesson 7

Developing Modular Applications

Self-Review: Quiz
1. On a subVI, which setting causes an error if the terminal is not wired? a. Required b. Recommended c. Optional 2. You must create an icon to use a VI as a subVI. a. True b. False

National Instruments Corporation

7-17

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

Self-Review: Quiz Answers

1. On a subVI, which setting causes an error if the terminal is not wired? a. Required b. Recommended c. Optional 2. You must create an icon to use a VI as a subVI. a. True b. False: you should customize the icon, but the default icon is enough for functionality.

National Instruments Corporation

7-19

LabVIEW Introduction Course Manual

Lesson 7

Developing Modular Applications

Notes

LabVIEW Introduction Course Manual

7-20

ni.com

Acquiring Data

A data acquisition (DAQ) system uses a data acquisition device to pass a conditioned electrical signal to a computer for software analysis and data logging. You can choose a data acquisition device that uses a PCI bus, a PCI Express bus, a PXI bus, or the computer USB or IEEE 1394 port. This lesson explains the hardware used in a data acquisition system, how to configure the devices and how to program analog input and output, counters, and digital input and output.

Topics
A. Using Hardware B. Communicating with Hardware C. Simulating a DAQ Device D. Measuring Analog Input E. Generating Analog Output F. Using Counters G. Using Digital I/O

National Instruments Corporation

8-1

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

A. Using Hardware
A typical DAQ system has three basic types of hardwarea terminal block, a cable, and a DAQ device, as shown in Figure 8-1.

2 3

NATIONAL INSTRUMENTS

NATIONAL INSTRUMENTS

5 1

1 2

Signal Terminal Block

3 4

Cable DAQ Device

Computer

Figure 8-1. Typical DAQ System

After you have converted a physical phenomenon into a measurable signal with or without signal conditioning, you need to acquire that signal. To acquire a signal, you need a terminal block, a cable, a DAQ device, and a computer. This hardware combination can transform a standard computer into a measurement and automation system.

Using a Terminal Block and Cable

A terminal block provides a place to connect signals. It consists of screw or spring terminals for connecting signals and a connector for attaching a cable to connect the terminal block to a DAQ device. Terminal blocks have 100, 68, or 50 terminals. The type of terminal block you should choose depends on two factorsthe device and the number of signals you are measuring. A terminal block with 68 terminals offers more ground terminals to connect a signal to than a terminal block with 50 terminals. Having more ground terminals prevents the need to overlap wires to reach a ground terminal, which can cause interference between the signals.

LabVIEW Introduction Course Manual

8-2

ni.com

Lesson 8

Acquiring Data

Terminal blocks can be shielded or non-shielded. Shielded terminal blocks offer better protection against noise. Some terminal blocks contain extra features, such as cold-junction compensation, that are necessary to properly measure a thermocouple. A cable transports the signal from the terminal block to the DAQ device. Cables come in 100-, 68-, and 50-pin configurations. Choose a configuration depending on the terminal block and the DAQ device you are using. Cables, like terminal blocks, are shielded or non-shielded. Refer to the DAQ section of the National Instruments catalog or to ni.com/ products for more information about specific types of terminal blocks and cables.

DAQ Signal Accessory

Figure 8-2 shows the terminal block you are using for this course, the DAQ Signal Accessory.

Power Quadrature A Encoder B

B Relay DIO 5 200mA Max

A B 68-pin Device (Diff Mode) Lab/1200 Series (NRSE Mode) 50-pin MIO Device (Diff Mode) 24 Pulses/rev Digital Trigger Digital Port 0 3 2 1 0 Counters Frequency Frequency Range Adjust 13kHz-1MHz 1kHz-100kHz Lo Hi 100Hz-10kHz Analog Analog Function Out In Generator Temp Sensor Noise Off On Temp Sensor Mic Ch 6

DAQ
Signal Accessory Ch 0 1 1 2

V*100 = C Ch 0

Figure 8-2. DAQ Signal Accessory

National Instruments Corporation

8-3

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

The DAQ Signal Accessory is a customized terminal block designed for learning purposes. It has three different cable connectors to accommodate many different DAQ devices and spring terminals to connect signals. You can access three analog input channels, one of which is connected to the temperature sensor, and two analog output channels. The DAQ Signal Accessory includes a function generator with a switch to select the frequency range of the signal, and a frequency knob. The function generator can produce a sine wave or a square wave. A connection to ground is located between the sine wave and square wave terminal. A digital trigger button produces a TTL pulse for triggering analog input or output. When you press the trigger button, the signal goes from +5 V to 0 V and returns to +5 V when you release the button. Four LEDs connect to the first four digital lines on the DAQ device. The LEDs use reverse logic, so when the digital line is high, the LED is off and vice versa. The DAQ Signal Accessory has a quadrature encoder that produces two pulse trains when you turn the encoder knob. Terminals are provided for the input and output signals of two counters on the DAQ device. The DAQ Signal Accessory also has a relay, a thermocouple input, and a microphone jack.

Using DAQ Devices

Most DAQ devices have four standard elementsanalog input, analog output, digital I/O, and counters. You can transfer the signal you measure with the DAQ device to the computer through a variety of different bus structures. For example, you can use a DAQ device that plugs into the PCI or PCI Express bus of a computer, a DAQ device connected to the PCMCIA socket of a laptop, or a DAQ device connected to the USB port of a computer. You also can use PXI/CompactPCI to create a portable, versatile, and rugged measurement system. If you do not have a DAQ device, you can simulate one in Measurement & Automation Explorer (MAX) to complete your software testing. You learn to simulate a device in the Simulating a DAQ Device section of this lesson. Refer to the DAQ section of the NI catalog or to ni.com/products for more information about specific types of DAQ devices.

LabVIEW Introduction Course Manual

8-4

ni.com

Lesson 8

Acquiring Data

B. Communicating with Hardware

National Instruments data acquisition devices have a driver engine that communicates between the device and the application software. There are two different driver engines to choose from: NI-DAQmx and Traditional NI-DAQ. You can use LabVIEW to communicate with these driver engines. You have already used the DAQ Assistant in LabVIEW to communicate with your data acquisition device. The DAQ Assistant is an Express VI that communicates with NI-DAQmx. In addition, you can use MAX to configure your data acquisition devices. In this section, you learn about the driver engines and about using MAX to configure your data acquisition device.

Using NI-DAQ
NI-DAQ 7.x contains two NI-DAQ driversTraditional NI-DAQ (Legacy) and NI-DAQmxeach with its own application programming interface (API), hardware configuration, and software configuration. NI-DAQ 8.0 and later come with only NI-DAQmx, the replacement for Traditional NI-DAQ (Legacy). Traditional NI-DAQ (Legacy) is an upgrade to NI-DAQ 6.9.x, the earlier version of NI-DAQ. Traditional NI-DAQ (Legacy) has the same VIs and functions and works the same way as NI-DAQ 6.9.x. You can use Traditional NI-DAQ (Legacy) on the same computer as NI-DAQmx, which you cannot do with NI-DAQ 6.9.x. However, you cannot use Traditional NI-DAQ (Legacy) on Windows Vista. NI-DAQmx is the latest NI-DAQ driver with new VIs, functions, and development tools for controlling measurement devices. The advantages of NI-DAQmx over previous versions of NI-DAQ include the DAQ Assistant for configuring channels and measurement tasks for a device; increased performance, including faster single-point analog I/O and multithreading; and a simpler API for creating DAQ applications using fewer functions and VIs than earlier versions of NI-DAQ.

Note (Windows) LabVIEW supports NI-DAQmx and the DAQ Assistant. (Linux) LabVIEW supports NI-DAQmx but not the DAQ Assistant. (Mac OS) LabVIEW

supports NI-DAQmx Base but not the DAQ Assistant. Traditional NI-DAQ (Legacy) and NI-DAQmx support different sets of devices. Refer to the National Instruments Web site at ni.com/daq for the list of supported devices. NI-DAQ 8.x comes with the latest version of the software driver, which is called NI-DAQmx. NI-DAQmx replaces Traditional NI-DAQ (Legacy).

National Instruments Corporation

8-5

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

NI-DAQmx and Traditional NI-DAQ (Legacy) have their own APIs, hardware configurations, and software configurations. LabVIEW supports NI-DAQmx on Windows and Linux and NI-DAQmx Base on Windows, Linux, and Mac OS. Refer to the NI-DAQ Readme for more information about platforms supported by NI-DAQ software.
Note

NI-DAQmx (Windows and Linux)

NI-DAQmx is the latest NI-DAQ driver with the following advantages over Traditional NI-DAQ (Legacy):
(Windows) DAQ Assistant, a graphical way to configure virtual channels

and measurement tasks for a device and to generate NI-DAQmx code based on virtual channels and tasks. Increased performance, including faster single-point analog I/O and multithreading. NI-DAQmx simulated devices for testing and modifying applications without plugging in hardware. Simpler, more intuitive APIs for creating DAQ applications using fewer functions and VIs than earlier versions of NI-DAQ. Expanded functionality for LabVIEW, including Property Nodes and waveform data type support. Improved support and performance for the LabVIEW Real-Time Module.

Traditional NI-DAQ (Legacy)

Traditional NI-DAQ (Legacy) is an upgrade of the earlier version of NI-DAQ. Traditional NI-DAQ (Legacy) has the same VIs and functions and works the same way as NI-DAQ 6.9.3, except you can use Traditional NI-DAQ (Legacy) and NI-DAQmx on the same computer, and some hardware is no longer supported. (Windows Vista) You cannot use Traditional NI-DAQ (Legacy) on Windows Vista.

Who Can Use NI-DAQmx

You should install and use NI-DAQmx if one of the following situations apply: You are a new NI-DAQ user. You are using devices supported by NI-DAQmx. Refer to the NI-DAQ Readme for a list of supported devices. You are using Windows Vista/XP/2000 or Linux.

LabVIEW Introduction Course Manual

8-6

ni.com

Lesson 8

Acquiring Data

Note (Linux) Refer to the National Instruments Web site for information about which Linux distributions NI-DAQmx supports. (Mac OS) LabVIEW supports a Base version of NI-DAQmx for Mac OS. Refer to the National Instruments Web site to download the NI-DAQmx Base driver.

Who Must Use Traditional NI-DAQ (Legacy)

You should use NI-DAQmx if you can. Install and use Traditional NI-DAQ (Legacy) if one of the following situations apply: You have a device that is not supported by NI-DAQmx, such as the AT E Series multifunction DAQ devices. You are using a version of LabVIEW earlier than version 7.0. You are upgrading from NI-DAQ 6.9.x and have existing applications that you do not want to port to NI-DAQmx.

Note The earliest version of NI application software supported by Traditional NI-DAQ (Legacy) is version 6.0. LabVIEW versions 6.x and 7.x can use Traditional NI-DAQ (Legacy) from the NI-DAQ 8.x distribution.

This lesson describes the NI-DAQmx API. When programming an NI measurement device, you can use NI application software such as LabVIEW, LabWindows/CVI, and Measurement Studio, or open ADEs that support calling dynamic link libraries (DLLs) through ANSI C interfaces. Using NI application software greatly reduces development time for data acquisition and control applications regardless of which programming environment you use: LabVIEW supports data acquisition with the LabVIEW DAQ VIs, a series of VIs for programming with NI measurement devices. For C developers, LabWindows/CVI is a fully integrated ANSI C environment that provides the LabWindows/CVI Data Acquisition library for programming NI measurement devices. Measurement Studio development tools are for designing your test and measurement software in Microsoft Visual Studio .NET. Measurement Studio includes tools for Visual C#, Visual Basic .NET, and Visual C++ .NET.

DAQ Hardware Configuration

Before using a data acquisition device, you must confirm that the software can communicate with the device by configuring the devices. The devices are already configured for the computers in this class.

National Instruments Corporation

8-7

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Windows
The Windows Configuration Manager keeps track of all the hardware installed in the computer, including National Instruments DAQ devices. If you have a Plug & Play (PnP) device, such as an E Series MIO device, the Windows Configuration Manager automatically detects and configures the device. If you have a non-PnP device, or legacy device, you must configure the device manually using the Add New Hardware option in the Windows Control Panel. You can verify the Windows Configuration by accessing the Device Manager. You can see Data Acquisition Devices, which lists all DAQ devices installed in the computer. Double-click a DAQ device to display a dialog box with tabbed pages. The General tab displays overall information regarding the device. The Resources tab specifies the system resources to the device such as interrupt levels, DMA, and base address for software-configurable devices. The NI-DAQ Information tab specifies the bus type of the DAQ device. The Driver tab specifies the driver version and location for the DAQ device.

Measurement & Automation Explorer

LabVIEW installs MAX, which establishes all device and channel configuration parameters. After installing a DAQ device in the computer, you must run this configuration utility. MAX reads the information the Device Manager records in the Windows Registry and assigns a logical device number to each DAQ device. Use the device number to refer to the device in LabVIEW. Access MAX by double-clicking the icon on the desktop or selecting ToolsMeasurement & Automation Explorer in LabVIEW. The following window is the primary MAX window. MAX is also the means for SCXI and SCC configuration.

1: AT-MIO-64E-3

LabVIEW Introduction Course Manual

8-8

ni.com

Lesson 8

Acquiring Data

The device parameters that you can set using the configuration utility depend on the device. MAX saves the logical device number and the configuration parameters in the Windows Registry. The plug and play capability of Windows automatically detects and configures switchless DAQ devices, such as the NI PCI-6024E. When you install a device in the computer, the device is automatically detected.

Scales
You can configure custom scales for your measurements. This is very useful when working with sensors. It allows you to bring a scaled value into your application without having to work directly with the raw values. For example, in this course you use a temperature sensor that represents temperature with a voltage. The conversion equation for the temperature is: Voltage x 100 = Celsius. After a scale is set, you can use it in your application program, providing the temperature value, rather than the voltage.

National Instruments Corporation

8-9

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

C. Simulating a DAQ Device

You can create NI-DAQmx simulated devices in NI-DAQmx 7.4 or later. Using NI-DAQmx simulated devices, you can try NI products in your application without the hardware. When you later acquire the hardware, you can import the NI-DAQmx simulated device configuration to the physical device using the MAX Portable Configuration Wizard. With NI-DAQmx simulated devices, you also can export a physical device configuration onto a system that does not have the physical device installed. Then, using the NI-DAQmx simulated device, you can work on your applications on a portable system and upon returning to the original system, you can easily import your application work.

Creating NI-DAQmx Simulated Devices

To create an NI-DAQmx simulated device, complete the following steps: 1. Right-click Devices and Interfaces and select Create New. 2. A dialog box prompts you to select a device to add. Select NI-DAQmx Simulated Device and click Finish. 3. In the Choose Device dialog box, select the category of devices for the device you want to simulate. 4. Select the device and click OK. In the configuration tree in MAX, the icons for NI-DAQmx simulated devices are yellow. If you select a PXI device, you are prompted to select a chassis number and PXI slot number. If you select an SCXI chassis, the SCXI configuration panels open. If you select a CompactDAQ chassis, you must right-click the empty slots to add C Series devices.

Removing NI-DAQmx Simulated Devices

To remove an NI-DAQmx simulated device, complete the following steps: 1. Expand Devices and InterfacesNI-DAQmx Devices. 2. Right-click the NI-DAQmx simulated device you want to delete. 3. Click Delete.
Note In the configuration tree in MAX, the icons for NI-DAQmx simulated devices are yellow. The icons for physical devices are green.

LabVIEW Introduction Course Manual

8-10

ni.com

Lesson 8

Acquiring Data

Exercise 8-1
Goal

Concept: MAX
Use MAX to examine, configure, and test a device.

Description
Complete the following steps to examine the configuration for the DAQ device in the computer using MAX. Use the test routines in MAX to confirm operation of the device. If you do not have a DAQ device, you can simulate a device using the instructions in Part A. Creating a Simulated Device.
Note Portions of this exercise that can only be completed with the use of a real device and a DAQ signal accessory are marked Hardware Installed. Some of these steps have alternative instructions for simulated devices and are marked No Hardware Installed.

1. Launch MAX by double-clicking the icon on the desktop or by selecting ToolsMeasurement & Automation Explorer in LabVIEW. MAX searches the computer for installed National Instruments hardware and displays the information.

Part A. Creating a Simulated Device

2. Create an NI-DAQmx simulated device to allow you to complete the exercises in this chapter without hardware. If you have a DAQ device installed, you can skip this step and go to Part B. Expand Devices and Interfaces. Right-click NI-DAQmx Devices and select Create New NI-DAQmx DeviceNI-DAQmx Simulated Device. In the Choose Device dialog box, select M Series DAQ NI PCI 6225. Click OK.

Part B. Examining the DAQ Device Settings

3. Expand the Devices and Interfaces section. 4. Expand the NI-DAQmx Devices section to view the installed National Instruments devices that use the NI-DAQmx driver.

National Instruments Corporation

8-11

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

5. Select the device listed in the NI-DAQmx Devices section. Figure 8-3 shows the PCI-MIO-16E-4 device.

Figure 8-3. MAX with Device and Interfaces Expanded

MAX displays the National Instruments hardware and software in the computer. The device number appears in quotes following the device name. The Data Acquisition VIs use this device number to determine which device performs DAQ operations. MAX also displays the attributes of the device such as the system resources that the device uses.
Note You might have a different device installed, and some of the options shown might be different. Click the Show Help/Hide Help button in the top right corner of MAX to hide the online help and show the DAQ device information. However, the Show Help/Hide Help button only appears in certain cases.

6. Select the Device Routes tab to see detailed information about the internal signals that can be routed to other destinations on the device, as shown in Figure 8-4. This is a powerful resource that gives you a visual representation of the signals that are available to provide timing and synchronization with components that are on the device and other external devices.

LabVIEW Introduction Course Manual

8-12

ni.com

Lesson 8

Acquiring Data

Figure 8-4. Device Routes

7. Select the Calibration tab, as shown in Figure 8-5, to see information about the last time the device was calibrated both internally and externally.

Figure 8-5. Calibration

National Instruments Corporation

8-13

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

8. Right-click the NI-DAQmx device in the configuration tree and select Self-Calibrate to calibrate the DAQ device using a precision voltage reference source and update the built-in calibration constants. When the device has been calibrated, the Self Calibration information updates in the Calibration tab. Skip this step if you are using a simulated device.

Part C. Testing the DAQ Device Components

9. Click the Self-Test button to test the device. This tests the system resources assigned to the device. The device should pass the test because it is already configured. 10. Click the Test Panels button to test the individual functions of the DAQ device, such as analog input and output. The Test Panels dialog box appears. Use the Analog Input tab to test the various analog input channels on the DAQ device. Click the Start button to acquire data from analog input channel 0. If you have a DAQ Signal Accessory, channel Dev1/ai0 is connected to the temperature sensor. Place your finger on the sensor to see the voltage rise. You also can move the Noise switch to On on the DAQ Signal Accessory to see the signal change in this tab. When you are finished, click the Stop button. If you are using a simulated device, a sine wave is shown on all input channels. Experiment with the setting on this tab. When you are finished, click the Stop button.

Click the Analog Output tab to set up a single voltage or sine wave on one of the DAQ device analog output channels. Change the output Mode to Sinewave Generation and click the Start button. LabVIEW generates a continuous sine wave on analog output channel 0. If you have hardware installed, wire Analog Out Ch0 to Analog In Ch1 on the DAQ Signal Accessory. If you have hardware installed, click the Analog Input tab and change the channel to Dev1/ai1. Click the Start button to acquire data from analog input channel 1. LabVIEW displays the sine wave from analog output channel 0. Click the Digital I/O tab to test the digital lines on the DAQ device. Set lines 0 through 3 as output and toggle the Logic Level checkboxes. If you have a DAQ signal accessory, toggling the boxes

LabVIEW Introduction Course Manual

8-14

ni.com

Lesson 8

Acquiring Data

turns the LEDs on or off. The LEDs use negative logic. Click Start to begin the digital output test. Click Stop to stop the digital output test. If you have hardware installed, click the Counter I/O tab to determine if the DAQ device counter/timers are functioning properly. To verify counter/timer operation, change the counter Mode tab to Edge Counting and click the Start button. The Counter Value increments rapidly. Click Stop to stop the counter test. Click the Close button to close the Test Panel and return to MAX.

Part D. Setting a Custom Scale

Complete this section only if you have hardware installed. If you do not have hardware installed, you are finished with this exercise. 11. Create a custom scale for the temperature sensor on the DAQ Signal Accessory. The sensor conversion is linear, and uses the following the formula Voltage x 100 = Celsius.

Figure 8-6. Temperature Scale

Right-click the Scales section and select Create New from the shortcut menu.
National Instruments Corporation 8-15 LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Select NI-DAQmx Scale. Click Next. Select Linear. Name the scale Temperature. Click Finish. Change the Scaling Parameters Slope to 100. Enter Celsius as the Scaled Units. Click the Save button on the toolbar to save the scale. You use this scale in later exercises. 12. Close MAX by selecting FileExit.

End of Exercise 8-1

LabVIEW Introduction Course Manual

8-16

ni.com

Lesson 8

Acquiring Data

D. Measuring Analog Input

Analog input is the process of measuring an analog signal and transferring the measurement to a computer for analysis, display or storage. An analog signal is a signal that varies continuously. Analog input is most commonly used to measure voltage or current. You can use many types of devices to perform analog input, such as multifunction DAQ (MIO) devices, high-speed digitizers, digital multimeters (DMMs) and Dynamic Signal Acquisition (DSA) devices.

Performing Analog-to-Digital Conversion

Acquiring an analog signal with a computer requires a process known as analog-to-digital conversion, which takes an electrical signal and translates it into digital data so that a computer can process it. Analog-to-digital converters (ADCs) are circuit components that convert a voltage level into a series of ones and zeroes. ADCs sample the analog signal on each rising or falling edge of a sample clock. In each cycle, the ADC takes a snapshot of the analog signal, so that the signal can be measured and converted into a digital value. A sample clock controls the rate at which samples of the input signal are taken. Because the incoming, or unknown signal is a real world signal with infinite precision, the ADC approximates the signal with fixed precision. After the ADC obtains this approximation, the approximation can be converted to a series of digital values. Some conversion methods do not require this step, because the conversion generates a digital value directly as the ADC reaches the approximation.

Using Task Timing

When performing analog input, the task can be timed to Acquire 1 Sample, Acquire n Samples, or Acquire Continuously.

Acquire 1 Sample
Acquiring a single sample is an on-demand operation. In other words, the driver acquires one value from an input channel and immediately returns the value. This operation does not require any buffering or hardware timing. For example, if you periodically monitor the fluid level in a tank, you would acquire single data points. You can connect the transducer that produces a voltage representing the fluid level to a single channel on the measurement device and initiate a single-channel, single-point acquisition when you want to know the fluid level.

National Instruments Corporation

8-17

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Acquire n Samples
One way to acquire multiple samples for one or more channels is to acquire single samples in a repetitive manner. However, acquiring a single data sample on one or more channels over and over is inefficient and time consuming. Moreover, you do not have accurate control over the time between each sample or channel. Instead you can use hardware timing, which uses a buffer in computer memory, to acquire data more efficiently. Programmatically, you need to include the timing function and specify the sample rate and the sample mode (finite). As with other functions, you can acquire multiple samples for a single channel or multiple channels. With NI-DAQmx, you also can gather data from multiple channels. For example, you might want to monitor both the fluid level in the tank and the temperature. In such a case, you need two transducers connected to two channels on the device.

Acquire Continuously
If you want to view, process, or log a subset of the samples as they are acquired, you need to continually acquire samples. For these types of applications, set the sample mode to continuous.

Using Task Triggering

A device controlled by NI-DAQmx reacts to a stimulus that causes the device to take a specific action. Every NI-DAQmx action needs a stimulus or cause. Two common actions include producing a sample and starting a waveform acquisition. After the stimulus occurs, the action is performed. The causes for actions are called triggers. For example, a start trigger starts data acquisition. The reference trigger establishes the reference point in a set of input samples. Data acquired up to the reference point is pretrigger data. Data acquired after the reference point is posttrigger data.

LabVIEW Introduction Course Manual

8-18

ni.com

Lesson 8

Acquiring Data

Exercise 8-2
Goal

Triggered Analog Input VI

Acquire an analog signal using a DAQ device and a digital trigger.

Scenario
Create a VI that measures the voltage signal on channel AI1 of the DAQ device. The VI begins measuring when a digital trigger is pressed and the Power switch on the front panel is on. The VI stops measuring when the Power switch on the front panel is off.

Design User Interface Inputs and Outputs

Type Waveform Chart Vertical Toggle Switch Name
Analog Input Data

Properties X-Scale range: 1/100 second

Power

External Inputs and Outputs

Inputs: AI1 of the data acquisition device. Connect the sine function generator to channel analog input 1 on the DAQ Signal Accessory with a wire. You also can use a DAQ Simulated Device to acquire data.

National Instruments Corporation

8-19

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Implementation
In the following steps, you build the front panel shown in Figure 8-7.

Figure 8-7. Triggered Analog Input front panel

1. Open a blank VI. 2. Create the Analog Input Data waveform chart. Add a Waveform Chart to the front panel window. Rename the waveform chart Analog Input Data. Resize the waveform chart to expand the x-axis. 3. Create the Power vertical toggle switch. Add a vertical toggle switch to the front panel window. Rename the switch Power. Create two free labels, Off and On, using the Labeling tool. Add the free labels as shown in Figure 8-7. 4. Save the VI as Triggered Analog Input.vi in the <Exercises>\ LabVIEW Basics I\Triggered Analog Input directory.

LabVIEW Introduction Course Manual

8-20

ni.com

Lesson 8

Acquiring Data

In the following steps, you create the block diagram shown in Figure 8-8.

Figure 8-8. Triggered Analog Input Block Diagram

5. Set up the DAQ Assistant to acquire data on AI1 at 50 KHz when the digital trigger is pressed. If you are using a simulated device, acquire the data without using a trigger. Switch to the block diagram. Add the DAQ Assistant Express VI to the block diagram. Select Acquire SignalsAnalog InputVoltage for the measurement to make. Select Dev1ai1 for the physical channel. Click the Finish button. Set the Signal Input Range on the Settings tab to a range of 1 to 1 Volts. Set the Acquisition Mode to Continuous Samples. Set the Samples to Read to 5000. The number of samples defines the amount of data removed from the buffer at one time. Set the Rate (Hz) to 50 KHz. If you are using the DAQ Signal Accessory, switch to the Triggering tab. If you are using a NI-DAQmx Simulated Device, click the OK button and skip to step 6. Set the Trigger Type in the Start Trigger section of the Triggering tab to Digital Edge. Set the Trigger Source to PFI0.

National Instruments Corporation

8-21

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Set the Edge to Rising. Click the OK button to close the Analog Input Voltage Task Configuration dialog box. 6. When prompted, allow LabVIEW to auto-generate a While Loop. Notice that it creates the While Loop and a Stop button for you. 7. Delete the Stop button; you use the Power switch instead. 8. Add the Power terminal to the While Loop. 9. Wire the Power terminal to the Stop input of the DAQ Assistant. 10. Convert the acquired data to an array of numerics to graph the data by sample number rather than time. Add a Convert from Dynamic Data Express VI to the While Loop. In the Config dialog box Select 1D array of scalars - automatic in the Resulting data type listbox. Click OK. 11. Confirm that the block diagram is wired as shown in Figure 8-8. 12. Switch to the front panel. 13. Save the VI.

Test
1. If you are using the DAQ Signal Accessory, confirm that a wire connects the sine function generator to analog in Ch 1. 2. Use the Operating Tool to add the Power switch in the On position.

LabVIEW Introduction Course Manual

8-22

ni.com

Lesson 8

Acquiring Data

3. Run the VI, then follow the instructions in either the Hardware Installed column or the No Hardware Installed column to begin acquiring data. Hardware Installed Press and release the Digital Trigger button on the DAQ Signal Accessory. The waveform chart should start displaying a sine wave. Change the frequency of the sine wave using the Frequency Adjust dial on the DAQ Signal Accessory. No Hardware Installed The waveform chart should start displaying a sine wave. You do not use a trigger because there is no physical trigger to switch.

4. Switch the Power switch to the Off position when you are finished. The VI should stop. 5. What happens if you start the VI with the Power switch in the Off position? Is this desired behavior? 6. Modify the Power switch so that it returns to the On position after it is clicked, and the On position is the default value. Use the Operating tool to add the Power switch to the On position. Right-click the Power switch and select Data OperationsMake Current Value Default from the shortcut menu. Right-click the Power switch and select Mechanical ActionLatch When Pressed from the shortcut menu. 7. Run the VI. Does the Power switch behave as you expect? 8. Stop and close the VI.

End of Exercise 8-2

National Instruments Corporation

8-23

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

E. Generating Analog Output

Analog output is the process of generating electrical signals from your computer. Analog output is generated by performing digital-to-analog (D/A) conversions. The available analog output types for a task are voltage and current. To perform a voltage or current task, a compatible device must be installed that can generate that form of signal.

Performing Task Timing

When performing analog output, the task can be timed to Generate 1 Sample, Generate n Samples, or Generate Continuously.

Generating 1 Sample
Use single updates if the signal level is more important than the generation rate. For example, generate one sample at a time if you need to generate a constant, or DC, signal. You can use software timing to control when the device generates a signal. This operation does not require any buffering or hardware timing. For example, if you need to generate a known voltage to stimulate a device, a single update would be an appropriate task.

Generating n Samples
One way to generate multiple samples for one or more channels is to generate single samples in a repetitive manner. However, generating a single data sample on one or more channels over and over is inefficient and time consuming. Moreover, you do not have accurate control over the time between each sample or channel. Instead, you can use hardware timing, which uses a buffer in computer memory to generate samples more efficiently. You can use software timing or hardware timing to control when a signal is generated. With software timing, the rate at which the samples are generated is determined by the software and operating system instead of by the measurement device. With hardware timing, a TTL signal, such as a clock on the device, controls the rate of generation. A hardware clock can run much faster than a software loop. A hardware clock is also more accurate than a software loop. Some devices do not support hardware timing. Consult the device documentation if you are unsure if the device supports hardware timing.
Note

LabVIEW Introduction Course Manual

8-24

ni.com

Lesson 8

Acquiring Data

Programmatically, you need to include the timing function, specifying the sample rate and the sample mode (finite). As with other functions, you can generate multiple samples for a single channel or multiple channels. Use Generate n Samples if you want to generate a finite, time-varying signal, such as an AC sine wave.

Generating Continuously
Continuous generation is similar to Generate n Samples, except that an event must occur to stop the generation. If you want to continuously generate signals, such as generating a non-finite AC sine wave, set the timing mode to continuous.

Performing Task Triggering

When a device controlled by NI-DAQmx does something, it performs an action. Two very common actions are producing a sample and starting a generation. Every NI-DAQmx action needs a stimulus or cause. When the stimulus occurs, the action is performed. Causes for actions are called triggers. A start trigger starts the generation.

Performing Digital-to-Analog Conversion

Digital-to-analog conversion is the opposite of analog-to-digital conversion. In digital-to-analog conversion, the computer generates the data. The data might have been acquired earlier using analog input or may have been generated by software on the computer. A digital-to-analog converter (DAC) accepts this data and uses it to vary the voltage on an output pin over time. The DAC generates an analog signal that the DAC can send to other devices or circuits. A DAC has an update clock that tells the DAC when to generate a new value. The function of the update clock is similar to the function of the sample clock for an analog-to-digital converter (ADC). At each cycle the clock, the DAC converts a digital value to an analog voltage and creates an output as a voltage on a pin. When used with a high speed clock, the DAC can create a signal that appears to vary constantly and smoothly.

National Instruments Corporation

8-25

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

F. Using Counters
A counter is a digital timing device. You typically use counters for event counting, frequency measurement, period measurement, position measurement, and pulse generation. Count RegisterStores the current count of the counter. You can query the count register with software. SourceAn input signal that can change the current count stored in the count register. The counter looks for rising or falling edges on the source signal. Whether a rising or falling edge changes the count is software selectable. The type of edge selected is referred to as the active edge of the signal. When an active edge is received on the source signal, the count changes. Whether an active edge increments or decrements the current count is also software selectable. GateAn input signal that determines if an active edge on the source changes the count. Counting can occur when the gate is high, low, or between various combinations of rising and falling edges. Gate settings are made in software. OutputAn output signal that generates pulses or a series of pulses, otherwise known as a pulse train.

When you configure a counter for simple event counting, the counter increments when an active edge is received on the source. In order for the counter to increment on an active edge, the counter must be armed or started. A counter has a fixed number it can count to as determined by the resolution of the counter. For example, a 24-bit counter can count to: 2(Counter Resolution) 1 = 224 1 = 16,777,215 When a 24-bit counter reaches the value of 16,777,215, it has reached the terminal count. The next active edge forces the counter to roll over and start at 0.

LabVIEW Introduction Course Manual

8-26

ni.com

Lesson 8

Acquiring Data

Exercise 8-3
Goal

Count Events VI
Use the DAQ Assistant to input a counter value.

Scenario
You have been asked to create a VI that counts pulses from the quadrature encoder on the DAQ Signal Accessory.

Design
Note

Complete this exercise only if you have hardware installed.

Quadrature Encoder
A 24-pulse per revolution mechanical quadrature encoder measures the position of a shaft as it rotates. The DAQ signal accessory quadrature encoder is a knob located in the upper central portion of the top panel. The quadrature encoder produces two pulse train outputs corresponding to the shaft position as you rotate the knob. Depending on the direction of rotation, phase A leads phase B by 90 or phase B leads phase A by 90. The DAQ Signal Accessory internally connects phase B of the quadrature encoder to the Up/Down line for Counter 0 (DIO6). Connect phase A of the quadrature encoder to the Source of Counter 0 (PFI8).

User Interface Inputs and Outputs

Type Numeric Indicator Stop Button Name
Number of Events stop (F)

Properties Double

External Inputs
Counter 0 Source (PFI8): Phase A of quadrature encoder Counter 0 Up/Down (DIO6): Phase B of quadrature encoder

Implementation
1. Open a blank VI. 2. Create an indicator for the current count. Add a numeric indicator to the front panel window.

National Instruments Corporation

8-27

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Label the numeric indicator Number of Events. Right-click the Number of Events indicator and select Display Format. Set the Digits to 8. 3. Save the VI as Count Events.vi in the <Exercises>\LabVIEW Basics I\Count Events directory. 4. Switch to the block diagram. 5. Configure the DAQ Assistant Express VI to use the counter to perform event counting.

Figure 8-9. Count Events VI Block Diagram

Add the DAQ Assistant Express VI to the block diagram. Select Acquire SignalsCounter InputEdge Count for the measurement to make. Select Dev1ctr0 for the physical channel. Click the Finish button. Change the Active Edge pull-down menu to Falling. Change the Count Direction pull-down menu to Externally Controlled. Click the OK button to close the configuration dialog box. When asked, allow LabVIEW to auto-generate a While Loop.

LabVIEW Introduction Course Manual

8-28

ni.com

Lesson 8

Acquiring Data

6. Finish building the block diagram. Use Figure 8-9 as a guide to assist you. LabVIEW can convert the dynamic type automatically, or you can use the From DDT Express VI to convert it.
Note

7. Save the VI.

Test
1. On the DAQ Signal Accessory, confirm that the A output of the quadrature encoder is wired to the SOURCE input of counter 0. 2. Run the VI.
Caution

If the VI does not work as you expect, you may need to reset the DAQ Device

in MAX. 3. Rotate the quadrature encoder knob on the DAQ Signal Accessory. Notice that the Number of Events indicator increments as you rotate the knob. The quadrature encoder knob produces pulses as you rotate the knob. The counter counts these pulses. Rotate the quadrature encoder knob in the other direction. Notice that the Number of Events indicator increments when you rotate the knob clockwise, and decrements when you rotate the knob counterclockwise. 4. Stop the VI. 5. Save and close the VI.

End of Exercise 8-3

National Instruments Corporation

8-29

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

G. Using Digital I/O

Digital signals are electrical signals that transfer digital data over a wire. These signals typically have only two stateson and off, also known as high and low, or 1 and 0. When sending a digital signal across a wire, the sender applies a voltage to the wire and the receiver uses the voltage level to determine the value being sent. The voltage ranges for each digital value depend on the voltage level standard being used. Digital signals have many uses; the simplest application of a digital signal is controlling or measuring digital or finite state devices such as switches and LEDs. Digital signals also can transfer data; you can use them to program devices or communicate between devices. In addition, you can use digital signals as clocks or triggers to control or synchronize other measurements. You can use the digital lines in a DAQ device to acquire a digital value. This acquisition is based on software timing. On some devices, you can configure the lines individually to either measure or generate digital samples. Each line corresponds to a channel in the task. You can use the digital port(s) in a DAQ device to acquire a digital value from a collection of digital lines. This acquisition is based on software timing. You can configure the ports individually to either measure or generate digital samples. Each port corresponds to a channel in the task.

LabVIEW Introduction Course Manual

8-30

ni.com

Lesson 8

Acquiring Data

Exercise 8-4
Goal

Optional: Digital Count VI

Use the DAQ Assistant for digital I/O.

Scenario
Write a VI that converts the number of events generated by the quadrature encoder to a digital number to display on the LEDs on the DAQ Signal Accessory. Because there are only four LEDs, you are limited to a number between 0 and 15 (24). For numbers greater than 15 and less than 0, the LEDs should continue changing as though there were more LEDs available.

Design
Note

Complete this exercise only if you have hardware installed.

Digital I/O
Each LED is wired to a digital line on the DAQ device. The lines are numbered 0, 1, 2, and 3, starting with the LED on the right. You can write to these lines individually or as a digital port. However, the digital port includes all 8 DIO lines. Because the quadrature encoder uses DIO6 for up/down counting, you cannot write to DIO6. Therefore, in this example, you should write a Boolean array to digital lines 04.

Flowchart
When a number is converted to a Boolean array, the number of elements in the array depends on the representation of the number used. If the number is 32-bytes, there are 32 elements in the Boolean array. However, because there are only four LEDs, you only need the first four elements of the array.

National Instruments Corporation

8-31

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Modify the Count Events VI as shown in the following flowchart.

Acquire Counter 0 Output

Convert Output to a Boolean Array

Reduce the Array to a 4 Element Array

Write Boolean Array to Digital Lines 0 - 3

No Stop? Yes

Figure 8-10. Digital Count Flowchart

LabVIEW Introduction Course Manual

8-32

ni.com

Lesson 8

Acquiring Data

Implementation
1. Open Count Events.vi in the <Exercises>\LabVIEW Basics I\Count Events directory. 2. Save the VI as Digital Count.vi. 3. Switch to the block diagram of the VI.

Figure 8-11. Digital Count VI Block Diagram

4. Delete the wire connected to the Number of Events indicator. 5. Enlarge the While Loop and increase the amount of space between the DAQ Assistant and the conditional terminal. 6. Convert the count to a Boolean array. Add a Convert From Dynamic Data Express VI to the right of the data output of the DAQ Assistant. Set the resulting data type to Single Scalar. Click OK to close the Configuration dialog box. Add a Number to Boolean Array function to the right of the Convert From Dynamic Data Express VI. Wire as shown in Figure 8-11. 7. Create a subarray containing the first four elements of the Boolean array. Add the Array Subset function to the right of the Number to Boolean Array function. Wire the output of the Number to Boolean Array function to the array input of the Array Subset function. Right-click the index input and select CreateConstant from the shortcut menu.

National Instruments Corporation

8-33

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Set the constant to 0. Right-click the length input and select CreateConstant from the shortcut menu. Set the constant to 4. 8. Configure digital lines 03 for edge counting. Add the DAQ Assistant Express VI to the While Loop. Select Generate SignalsDigital OutputLine Output for the measurement to make. Select Dev1line 0line 3 for the physical channels and click the Finish button.
Note

Press the <Ctrl> key to select multiple lines. For each line, select Invert Line because the LEDs use negative logic. Click the OK button to close the configuration dialog box.

Note In this exercise, you use individual lines rather than a port because DIO6 is used by Phase B of the Quadrature Encoder.

9. Wire the block diagram as shown in Figure 8-11. 10. Save the VI.

Test
1. Display the front panel. 2. Run the VI. 3. Turn the quadrature encoder and observe the changes on the DAQ Signal Accessory. 4. Stop and close the VI.

End of Exercise 8-4

LabVIEW Introduction Course Manual

8-34

ni.com

Lesson 8

Acquiring Data

Self-Review: Quiz
1. You are reading a signal at 50 kHz. You want to acquire the signal until a stop trigger is pressed. Which task timing should you use? a. Acquire 1 Sample b. Acquire n Samples c. Acquire Continuously 2. Your VI monitors a factory floor. Part of the VI controls an LED that alerts users to the status of the system. Which task timing should you use? a. Generate 1 Sample b. Generate n Samples c. Generate Continuously

National Instruments Corporation

8-35

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Self-Review: Quiz Answers

1. You are reading a signal at 50kHz. You want to acquire the signal until a stop trigger is pressed. Which task timing should you use? a. Acquire 1 Sample b. Acquire n Samples c. Acquire Continuously 2. Your VI monitors a factory floor. Part of the VI controls an LED that alerts users to the status of the system. Which task timing should you use? a. Generate 1 Sample b. Generate n Samples c. Generate Continuously

National Instruments Corporation

8-37

LabVIEW Introduction Course Manual

Lesson 8

Acquiring Data

Notes

LabVIEW Introduction Course Manual

8-38

ni.com

Instrument Control

This lesson describes how to control stand-alone instruments using a GPIB or serial interface. Use LabVIEW to control and acquire data from instruments with the Instrument I/O Assistant, the VISA API, and instrument drivers.

Topics
A. Using Instrument Control B. Using GPIB C. Using Serial Port Communication D. Using Other Interfaces E. Software Architecture F. Using the Instrument I/O Assistant G. Using VISA H. Using Instrument Drivers

National Instruments Corporation

9-1

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

A. Using Instrument Control

When you use a PC to automate a test system, you are not limited to the type of instrument you can control. You can mix and match instruments from various categories. The most common categories of instrument interfaces are GPIB, serial, modular instruments, and PXI modular instruments. Additional types of instruments include image acquisition, motion control, USB, Ethernet, parallel port, NI-CAN, and other devices. When you use PCs to control instruments, you need to understand properties of the instrument, such as the communication protocols to use. Refer to the instrument documentation for information about the properties of an instrument.

B. Using GPIB
The ANSI/IEEE Standard 488.1-1987, also known as General Purpose Interface Bus (GPIB), describes a standard interface for communication between instruments and controllers from various vendors. GPIB, or General Purpose Interface Bus, instruments offer test and manufacturing engineers the widest selection of vendors and instruments for general-purpose to specialized vertical market test applications. GPIB instruments are often used as stand-alone benchtop instruments where measurements are taken by hand. You can automate these measurements by using a PC to control the GPIB instruments. IEEE 488.1 contains information about electrical, mechanical, and functional specifications. The ANSI/IEEE Standard 488.2-1992 extends IEEE 488.1 by defining a bus communication protocol, a common set of data codes and formats, and a generic set of common device commands. GPIB is a digital, 8-bit parallel communication interface with data transfer rates of 1 Mbyte/s and higher, using a three-wire handshake. The bus supports one system controller, usually a computer, and up to 14 additional instruments. The GPIB protocol categorizes devices as controllers, talkers, or listeners to determine which device has active control of the bus. Each device has a unique GPIB primary address between 0 and 30. The Controller defines the communication links, responds to devices that request service, sends GPIB commands, and passes/receives control of the bus. Controllers instruct Talkers to talk and to place data on the GPIB. You can address only one device at a time to talk. The Controller addresses the Listener to listen and to read data from the GPIB. You can address several devices to listen.

LabVIEW Introduction Course Manual

9-2

ni.com

Lesson 9

Instrument Control

Data Transfer Termination

Termination informs listeners that all data has been transferred. You can terminate a GPIB data transfer in the following three ways: The GPIB includes an End Or Identify (EOI) hardware line that can be asserted with the last data byte. This is the preferred method. Place a specific end-of-string (EOS) character at the end of the data string itself. Some instruments use this method instead of or in addition to the EOI line assertion. The listener counts the bytes transferred by handshaking and stops reading when the listener reaches a byte count limit. This method is often a default termination method because the transfer stops on the logical OR of EOI, EOS (if used) in conjunction with the byte count. Thus, you typically set the byte count to equal or exceed the expected number of bytes to be read.

Data Transfer Rate

To achieve the high data transfer rate that the GPIB was designed for, you must limit the number of devices on the bus and the physical distance between devices. You can obtain faster data rates with HS488 devices and controllers. HS488 is an extension to GPIB that most NI controllers support.
Note Refer to the National Instruments GPIB support Web site at ni.com/support/ gpibsupp.htm for more information about GPIB.

C. Using Serial Port Communication

Serial communication transmits data between a computer and a peripheral device, such as a programmable instrument or another computer. Serial communication uses a transmitter to send data one bit at a time over a single communication line to a receiver. Use this method when data transfer rates are low or you must transfer data over long distances. Most computers have one or more serial ports, so you do not need any extra hardware other than a cable to connect the instrument to the computer or to connect two computers to each other.

National Instruments Corporation

9-3

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

1 3
76.6F

RS-232 Instrument

RS-232 Cable

Serial Port

Figure 9-1. Serial Instrument Example

You must specify four parameters for serial communication: the baud rate of the transmission, the number of data bits that encode a character, the sense of the optional parity bit, and the number of stop bits. A character frame packages each transmitted character as a single start bit followed by the data bits. Baud rate is a measure of how fast data moves between instruments that use serial communication. Data bits are transmitted upside down and backwards, which means that inverted logic is used and the order of transmission is from least significant bit (LSB) to most significant bit (MSB). To interpret the data bits in a character frame, you must read from right to left and read 1 for negative voltage and 0 for positive voltage. An optional parity bit follows the data bits in the character frame. The parity bit, if present, also follows inverted logic. This bit is included as a means of error checking. You specify ahead of time for the parity of the transmission to be even or odd. If you choose for the parity to be odd, the parity bit is set in such a way so the number of 1s add up to make an odd number among the data bits and the parity bit. The last part of a character frame consists of 1, 1.5, or 2 stop bits that are always represented by a negative voltage. If no further characters are transmitted, the line stays in the negative (MARK) condition. The transmission of the next character frame, if any, begins with a start bit of positive (SPACE) voltage.

LabVIEW Introduction Course Manual

9-4

ni.com

Lesson 9

Instrument Control

The following figure shows a typical character frame encoding the letter m.

Idle

Start Bit

Data Bits

Parity Bit

Stop Bits

Idle

Space Mark

Bit Time

Character Frame

Figure 9-2. Character Frame for the Letter m

RS-232 uses only two voltage states, called MARK and SPACE. In such a two-state coding scheme, the baud rate is identical to the maximum number of bits of information, including control bits, that are transmitted per second. MARK is a negative voltage, and SPACE is positive. The previous illustration shows how the idealized signal looks on an oscilloscope. The following is the truth table for RS-232: Signal > +3 V = 0 Signal < 3 V = 1 The output signal level usually swings between +12 V and 12 V. The dead area between +3 V and 3 V is designed to absorb line noise. A start bit signals the beginning of each character frame. It is a transition from negative (MARK) to positive (SPACE) voltage. Its duration in seconds is the reciprocal of the baud rate. If the instrument is transmitting at 9,600 baud, the duration of the start bit and each subsequent bit is about 0.104 ms. The entire character frame of eleven bits would be transmitted in about 1.146 ms. Interpreting the data bits for the transmission yields 1101101 (binary) or 6D (hex). An ASCII conversion table shows that this is the letter m. This transmission uses odd parity. There are five ones among the data bits, already an odd number, so the parity bit is set to 0.

Data Transfer Rate

You can calculate the maximum transmission rate in characters per second for a given communication setting by dividing the baud rate by the bits per character frame.

National Instruments Corporation

9-5

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

In the previous example, there are a total of eleven bits per character frame. If the transmission rate is set at 9,600 baud, you get 9,600/11 = 872 characters per second. Notice that this is the maximum character transmission rate. The hardware on one end or the other of the serial link might not be able to reach these rates, for various reasons.

Serial Port Standards

The following examples are the most common recommended standards of serial port communication: RS232 (ANSI/EIA-232 Standard) is used for many purposes, such as connecting a mouse, printer, or modem. It also is used with industrial instrumentation. Because of improvements in line drivers and cables, applications often increase the performance of RS232 beyond the distance and speed in the standards list. RS232 is limited to point-to-point connections between PC serial ports and devices. RS422 (AIA RS422A Standard) uses a differential electrical signal as opposed to the unbalanced (single-ended) signals referenced to ground with RS232. Differential transmission, which uses two lines each to transmit and receive signals, results in greater noise immunity and longer transmission distances as compared to RS232. RS485 (EIA-485 Standard) is a variation of RS422 that allows you to connect up to 32 devices to a single port and define the necessary electrical characteristics to ensure adequate signal voltages under maximum load. With this enhanced multidrop capability, you can create networks of devices connected to a single RS485 serial port. The noise immunity and multidrop capability make RS485 an attractive choice in industrial applications that require many distributed devices networked to a PC or other controller for data collection and other operations.

D. Using Other Interfaces

There are devices made to communicate with serial or GPIB instruments through the Ethernet, USB, or IEEE 1394 (FireWire) ports, which bypasses the need for a serial port or GPIB device on your computer. When using these devices, program them just as you would if they were using the serial port or a GPIB device. USB and ethernet interfaces transform USB ports or ethernet ports into asynchronous serial ports for communication with serial instruments. You can install and use these interfaces as standard serial ports from your existing applications.

LabVIEW Introduction Course Manual

9-6

ni.com

Lesson 9

Instrument Control

USB, ethernet, and IEEE 1394 controllers transform any computer with these ports into a full-function, Plug and Play, IEEE-488.2 controller that can control up to 14 programmable GPIB instruments.

E. Software Architecture
The software architecture for instrument control using LabVIEW is similar to the architecture for DAQ. Instrument interfaces such as GPIB include a set of drivers. Use MAX to configure the interface. Virtual Instrument Software Architecture (VISA), is a common API to communicate with the interface drivers and is the preferred method used when programming for instrument control in LabVIEW, because VISA abstracts the type of interface used. Many LabVIEW VIs for instrument control use the VISA API. For example, the Instrument I/O Assistant is a LabVIEW Express VI that can use VISA to communicate with message-based instruments and convert the response from raw data to an ASCII representation. Use the Instrument I/O Assistant when an instrument driver is not available. In LabVIEW, an instrument driver is a set of VIs written to communicate with an instrument. GPIB drivers are available on the LabVIEW Installer CD-ROM and most GPIB drivers are available for download at ni.com/support/gpib/versions.htm. Always install the newest version of these drivers unless otherwise instructed in the release notes.
Note

MAX (Windows; GPIB)

Use MAX to configure and test the GPIB interface. MAX interacts with the various diagnostic and configuration tools installed with the driver and also with the Windows Registry and Device Manager. The driver-level software is in the form of a DLL and contains all the functions that directly communicate with the GPIB interface. The Instrument I/O VIs and functions directly call the driver software. Open MAX by double-clicking the icon on the desktop or by selecting ToolsMeasurement & Automation Explorer in LabVIEW. The following example shows a GPIB interface in MAX after clicking the Scan For Instruments button on the toolbar.

National Instruments Corporation

9-7

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Figure 9-3. GPIB Interface in Measurement and Automation Explorer

Configure the objects listed in MAX by right-clicking each item and selecting an option from the shortcut menu. You learn to use MAX to configure and communicate with a GPIB instrument in the next exercise.

LabVIEW Introduction Course Manual

9-8

ni.com

Lesson 9

Instrument Control

Exercise 9-1
Goal

Concept: GPIB Configuration with MAX

Learn to configure the NI Instrument Simulator and use MAX to examine the GPIB interface settings, detect instruments, and communicate with an instrument. This lesson uses one of the following NI Instrument Simulators. Follow the instructions for the Instrument Simulator you are using.
BAUD RATE DATA FORMAT S MODE OFF

ON
GPIB ADDRESS G MODE ON

OFF

Figure 9-4. NI Instrument Simulator A with DIP Switches

Figure 9-5. NI Instrument Simulator B Rear Panel

If you are using NI Instrument Simulator A, shown in Figure 9-4, follow the instructions in part A of this exercise. If you are using NI Instrument Simulator B, shown in Figure 9-5, follow the instructions in part B of this exercise.

Part A: NI Instrument Simulator A Description

1. Configure the NI Instrument Simulator. Power off the NI Instrument Simulator. Set the left bank of switches on the side of the box to match Figure 9-6. Power on the NI Instrument Simulator.

National Instruments Corporation

9-9

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Verify that both the Power and Ready LEDs are lit.
OFF

ON 1 2

GPIB Address

G Mode

Figure 9-6. GPIB Configuration Settings for the NI Instrument Simulator A

2. Launch MAX by double-clicking the icon on the desktop or selecting ToolsMeasurement & Automation Explorer in LabVIEW. 3. View the settings for the GPIB interface. Expand the Devices and Interfaces section to display the installed interfaces. If a GPIB interface is listed, the NI-488.2 software is correctly loaded on the computer. Select the GPIB interface. Examine but do not change the settings for the GPIB interface. 4. Communicate with the GPIB instrument. Make sure the GPIB interface is still selected in the Devices and Interfaces section. Click the Scan for Instruments button on the toolbar. Expand the GPIB interface that is selected in the Devices and Interfaces section. One instrument named Instrument0 appears. Click Instrument0 to display information about it in the right pane of MAX. Notice that the NI Instrument Simulator has a GPIB primary address (PAD) of 2. Click the Communicate with Instrument button on the toolbar. An interactive window appears. You can use it to query, write to, and read from that instrument. Enter *IDN? in Send String and click the Query button. The instrument returns its make and model number in String Received as shown in Figure 9-7. You can use this window to debug

LabVIEW Introduction Course Manual

9-10

ni.com

Lesson 9

Instrument Control

instrument problems or to verify that specific commands work as described in the instrument documentation.

Figure 9-7. Communication with the GPIB Instrument

Enter MEAS:DC? in Send String and click the Query button. The NI Instrument Simulator returns a simulated voltage measurement. Click the Query button again to return a different value. Click the Exit button when done. 5. Set a VISA alias of devsim for the NI Instrument Simulator so you can use the alias instead of having to remember the primary address. While Instrument0 is selected in MAX, select the VISA Properties tab. Enter devsim in the VISA Alias on My System field. You will use this alias throughout this lesson. 6. Select FileExit to exit MAX. 7. Click Yes when prompted to save the instrument.

Part B: NI Instrument Simulator B Description

1. Configure the NI Instrument Simulator. Power off the NI Instrument Simulator. Set the configuration switch on the rear panel to CFG, as shown in Figure 9-8.

National Instruments Corporation

9-11

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Figure 9-8. NI Instrument Simulator B

Power on the NI Instrument Simulator using the power switch on the front of the unit. Verify that the Power LED is lit and the Ready LED is flashing. Launch the NI Instrument Simulator Wizard from Start ProgramsNational InstrumentsNI Instrument Simulator. Follow the onscreen instructions in the wizard to configure the NI Instrument Simulator for the default settings for serial and GPIB. Verify that both the Power and Ready LEDs are lit. 2. Launch MAX by either double-clicking the icon on the desktop or by selecting ToolsMeasurement & Automation Explorer in LabVIEW. 3. View the settings for the GPIB interface. Expand the Devices and Interfaces section to display the installed interfaces. If a GPIB interface is listed, the NI-488.2 software is correctly loaded on the computer. Select the GPIB interface. Examine but do not change the settings for the GPIB interface. 4. Communicate with the GPIB instrument. Make sure the GPIB interface is still selected in the Devices and Interfaces section. Click the Scan for Instruments button on the toolbar. Expand the GPIB interface that is selected in the Devices and Interfaces section. One instrument named Instrument0 appears. Click Instrument0 to display information about it in the right pane of MAX. Notice the NI Instrument Simulator has a GPIB primary address (PAD).

LabVIEW Introduction Course Manual

9-12

ni.com

Lesson 9

Instrument Control

Click the Communicate with Instrument button on the toolbar. An interactive window appears. You can use it to query, write to, and read from that instrument. Enter *IDN? in Send String and click the Query button. The instrument returns its make and model number in String Received as shown in Figure 9-9. You can use this window to debug instrument problems or to verify that specific commands work as described in the instrument documentation.

Figure 9-9. Communication with the GPIB Instrument

Enter MEASURE:VOLTAGE:DC? in Send String and click the Query button. The NI Instrument Simulator returns a simulated voltage measurement. Click the Query button again to return a different value. Click the Exit button when done. 5. Set a VISA alias of devsim for the NI Instrument Simulator so you can use the alias instead of having to remember the primary address. While Instrument0 is selected in MAX, select the VISA Properties tab. Enter devsim in the VISA Alias on My System field. You will use this alias throughout this lesson. 6. Select FileExit to exit MAX. 7. Click Yes when prompted to save the instrument.

End of Exercise 9-1

National Instruments Corporation

9-13

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

F. Using the Instrument I/O Assistant

The Instrument I/O Assistant is a LabVIEW Express VI which you can use to communicate with message-based instruments and convert the response from raw data to an ASCII representation. You can communicate with an instrument that uses a serial, Ethernet, or GPIB interface. Use the Instrument I/O Assistant when an instrument driver is not available. The Instrument I/O Assistant organizes instrument communication into ordered steps. To use Instrument I/O Assistant, you place steps into a sequence. As you add steps to the sequence, they appear in the Step Sequence window. Use the view associated with a step to configure instrument I/O. To launch the Instrument I/O Assistant, place the Instrument I/O Assistant Express VI on the block diagram in LabVIEW. The Instrument I/O Assistant Express VI is available in the Instrument I/O category of the Functions palette. The Instrument I/O Assistant configuration dialog box appears. If it does not appear, double-click the Instrument I/O Assistant icon. Complete the following steps to configure the Instrument I/O Assistant. 1. Select an instrument. Instruments that have been configured in MAX appear in the Select an instrument pull-down menu. 2. Choose a Code generation type. VISA code generation allows for more flexibility and modularity than GPIB code generation. 3. Select from the following communication steps using the Add Step button: Query and ParseSends a query to the instrument, such as *IDN? and parses the returned string. This step combines the Write command and Read and Parse command. WriteSends a command to the instrument. Read and ParseReads and parses data from the instrument

4. After adding the desired number of steps, click the Run button to test the sequence of communication that you have configured for the Express VI. 5. Click the OK button to exit the Instrument I/O Assistant configuration dialog box. LabVIEW adds input and output terminals to the Instrument I/O Assistant Express VI on the block diagram that correspond to the data you receive from the instrument.

LabVIEW Introduction Course Manual

9-14

ni.com

Lesson 9

Instrument Control

To view the code generated by the Instrument I/O Assistant, right-click the Instrument I/O Assistant icon and select Open Front Panel from the shortcut menu. This converts the Express VI to a subVI. Switch to the block diagram to see the code generated.
Note After you convert an Express VI to a subVI, you cannot reconvert the subVI to an Express VI.

National Instruments Corporation

9-15

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Exercise 9-2
Goal

Concept: Instrument I/O Assistant

Configure a serial or GPIB instrument and communicate with the instrument using the Instrument I/O Assistant. Select the exercise instructions that correspond to your instrument simulator and communication method from the following choices: NI Instrument Simulator A, serial communication, complete the instructions in the Part A: Serial with NI Instrument Simulator A Description section of this exercise. NI Instrument Simulator A, GPIB communication, complete the instructions in the Part B: GPIB with NI Instrument Simulator A Description section of this exercise. NI Instrument Simulator B, serial communication, complete the instructions in the Part C: Serial with NI Instrument Simulator B Description section of this exercise. NI Instrument Simulator B, GPIB communication, complete the instructions in the Part D: GPIB with NI Instrument Simulator B Description section of this exercise.

Part A: Serial with NI Instrument Simulator A Description

1. Configure the NI Instrument Simulator A to communicate through the serial port. Power off the NI Instrument Simulator. Set the left bank of switches on the side of the box to match Figure 9-10.
1 2 3 OFF

ON

S Mode

Data Format

Baud Rate

Figure 9-10. Serial Configuration Settings for the NI Instrument Simulator A

Make sure the NI Instrument Simulator is connected to a serial port on the computer with a serial cable.

LabVIEW Introduction Course Manual

9-16

ni.com

Lesson 9

Instrument Control

Make a note of the port number. Power on the NI Instrument Simulator. Verify that the Power, Ready, and Listen LEDs are lit to indicate that the device is in serial communication mode. You create a block diagram similar to the one in Figure 9-11 in the following steps.

Figure 9-11. Serial IIOA A VI Block Diagram

2. Open a blank VI. 3. Save the VI as Serial IIOA Read A.vi in the <Exercises>\ LabVIEW Basics I\Instrument IO Assistant directory. 4. Open the block diagram. 5. Configure the Instrument I/O Express VI to communicate with the NI Instrument Simulator. Place the Instrument I/O Express VI on the block diagram. The Instrument I/O Assistant dialog box appears.

National Instruments Corporation

9-17

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Figure 9-12. Serial Configuration of the Instrument I/O Assistant

From the Select an instrument pull-down menu, choose COM1 (or COM2 depending on the connection port of the NI Instrument Simulator). From the Termination Character pull-down menu, choose \n. Click the Add Step button. Click Write. In the command field, enter *IDN?. Click the Add Step button. Click Read and Parse.

LabVIEW Introduction Course Manual

9-18

ni.com

Lesson 9

Instrument Control

Note The Instrument Simulator returns the byte size of the response, the termination character, the response, then another termination character. Therefore, after *IDN? is sent to the instrument, the response must be read twice; once to retrieve the size of the response, and once to retrieve the response.

Click the Add Step button. Click Read and Parse again. Click the Run button (not the Run this step button). The Run button runs the entire sequence. Return to the first Read and Parse step. Click the Auto parse button. The value returned is the size in bytes of the query response. Rename Token to String Length in the Token name text box. Select the second Read and Parse step. Click the Auto parse button. The value returned is the identification string of the NI Instrument Simulator. Rename Token to String in the Token name text box. The configuration window should be similar to Figure 9-12. Click OK to return to the block diagram. 6. Create an indicator for the response from the instrument. Right-click the String terminal. Select CreateIndicator from the shortcut menu. 7. Create an indicator for the response length from the instrument. Right-click the String Length terminal. Select CreateIndicator from the shortcut menu.
Tip To allow LabVIEW to handle errors automatically, do not connect a Simple Error Handler VI to error out.

8. Display the front panel window. It should be similar to Figure 9-13.

National Instruments Corporation

9-19

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Figure 9-13. Serial IIOA A VI Front Panel Window

9. Save the VI. 10. Run the VI. 11. Examine the code generated by the I/O Assistant. Right-click the I/O Assistant and select Open Front Panel. Click the Convert button when asked if you want to convert to a subVI. View the code generated by the I/O Assistant. Where is the command *IDN? written to the Instrument Simulator? Select FileClose to exit the subVI. Do not save changes. 12. Close the VI when finished.

Part B: GPIB with NI Instrument Simulator A Description

1. Configure the NI Instrument Simulator A to communicate through the GPIB interface. Power off the NI Instrument Simulator. Set the left bank of switches on the side of the box to match Figure 9-14.
OFF

ON 1 2

GPIB Address

G Mode

Figure 9-14. GPIB Configuration Settings for the NI Instrument Simulator A

LabVIEW Introduction Course Manual

9-20

ni.com

Lesson 9

Instrument Control

Make sure the NI Instrument Simulator is connected to the GPIB device. Power on the NI Instrument Simulator. Verify that both the Power and Ready LEDs are lit. 2. Open a blank VI. 3. Save the VI as GPIB IIOA Read A.vi in the <Exercises>\ LabVIEW Basics I\Instrument IO Assistant directory. You create a block diagram similar to the one in Figure 9-15 in the following steps.

Figure 9-15. GPIB IIOA A VI Block Diagram

4. Open the block diagram. 5. Configure the Instrument I/O Express VI to communicate with the NI Instrument Simulator. Place the Instrument I/O Express VI on the block diagram. The Instrument I/O Assistant dialog box appears.

National Instruments Corporation

9-21

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Figure 9-16. GPIB Configuration of the Instrument I/O Assistant

Select devsim from the Select an instrument pull-down menu. Select VISA Code Generation from the Code generation type pull-down menu. Click the Add Step button. Click Query and Parse to write and read from the Instrument Simulator. Enter *IDN? as the command. Click the Run this step button. If no error warning appears in the lower half of the dialog box, this step has successfully completed. To parse the data received, click the Auto parse button. Rename Token by typing ID String in the Token name text box.

LabVIEW Introduction Course Manual

9-22

ni.com

Lesson 9

Instrument Control

Click the Add Step button. Click Query and Parse. Enter MEAS:DC? as the command. Click the Run this step button. To parse the data received, click the Auto parse button. The data returned is a random numeric value. Rename Token by typing Voltage in the Token name text box. The configuration window should be similar to Figure 9-16. Click the OK button to exit the I/O Assistant and return to the block diagram. 6. Create an indicator for the ID String. Right-click the ID String terminal and select CreateIndicator from the shortcut menu. 7. Create an indicator for the voltage. Right-click the Voltage terminal and select CreateIndicator from the shortcut menu.
Tip To allow LabVIEW to handle errors automatically, do not connect a Simple Error Handler VI to error out.

8. Display the front panel window. The front panel window should be similar in Figure 9-17.

Figure 9-17. GPIB IIOA A VI Front Panel Window

9. Save the VI. 10. Run the VI. Resize the string indicator if necessary.

National Instruments Corporation

9-23

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

11. Examine the code generated by the I/O Assistant. Right-click the I/O Assistant and select Open Front Panel. Click the Convert button when prompted to convert to a subVI. View the code generated by the I/O Assistant. Where is the command *IDN? written to the Instrument Simulator? Where is the voltage being read? Select FileClose to exit the subVI. Do not save changes. 12. Close the VI when finished.

Part C: Serial with NI Instrument Simulator B Description

1. Verify that the Power and Ready LEDs are lit. 2. Open a blank VI. 3. Save the VI as Serial IIOA Read B.vi in the <Exercises>\ LabVIEW Basics I\Instrument IO Assistant directory. You create a block diagram similar to the one in Figure 9-18 in the following steps.

Figure 9-18. Serial IIOA A VI Block Diagram

4. Open the block diagram. 5. Configure the Instrument I/O Express VI to communicate with the NI Instrument Simulator. Place the Instrument I/O Express VI on the block diagram. The Instrument I/O Assistant dialog box appears.

LabVIEW Introduction Course Manual

9-24

ni.com

Lesson 9

Instrument Control

Figure 9-19. Serial Configuration of the Instrument I/O Assistant

From the Select an instrument pull-down menu, choose COM1 (or COM2 depending on the connection port of the NI Instrument Simulator). From the Termination Character pull-down menu, choose \n. Click the Add Step button. Click Query and Parse to write and read from the Instrument Simulator. Enter *IDN? as the command. Click the Run this step button. If no error warning appears in the lower half of the dialog box, this step has successfully completed. Click the Separator(s) text box and delete its contents.

National Instruments Corporation

9-25

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

To parse the data received, click the Auto parse button. Rename Token by typing ID String in the Token name text box. Click the Add Step button. Click Query and Parse. Enter MEASURE:VOLTAGE:DC? as the command. Click the Run this step button. To parse the data received, click the Auto parse button. The data returned is a random numeric value. Rename Token by typing Voltage in the Token name text box. The configuration window should be similar to Figure 9-19. Click the OK button to exit the I/O Assistant and return to the block diagram. 6. Create an indicator for the ID String. Right-click the ID String terminal and select CreateIndicator from the shortcut menu. 7. Create an indicator for the voltage. Right-click the Voltage terminal and select CreateIndicator from the shortcut menu.
Tip To allow LabVIEW to handle errors automatically, do not connect a Simple Error Handler VI to error out.

8. Display the front panel window. The front panel window should be similar in Figure 9-20.

Figure 9-20. Serial IIOA A VI Front Panel Window

9. Save the VI.

LabVIEW Introduction Course Manual

9-26

ni.com

Lesson 9

Instrument Control

10. Run the VI. Resize the string indicator if necessary. 11. Examine the code generated by the I/O Assistant. Right-click the I/O Assistant and select Open Front Panel. Click the Convert button when prompted to convert to a subVI. View the code generated by the I/O Assistant. Where is the command *IDN? written to the Instrument Simulator? Where is the voltage being read? Select FileClose to exit the subVI. Do not save changes. 12. Close the VI when finished.

Part D: GPIB with NI Instrument Simulator B Description

1. Verify that the Power and Ready LEDs are lit. 2. Open a blank VI. 3. Save the VI as GPIB IIOA Read B.vi in the <Exercises>\ LabVIEW Basics I\Instrument IO Assistant directory. You create a block diagram similar to the one in Figure 9-21 in the following steps.

Figure 9-21. GPIB IIOA A VI Block Diagram

4. Open the block diagram. 5. Configure the Instrument I/O Express VI to communicate with the NI Instrument Simulator. Place the Instrument I/O Express VI on the block diagram. The Instrument I/O Assistant dialog box appears.

National Instruments Corporation

9-27

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Figure 9-22. GPIB Configuration of the Instrument I/O Assistant

Select devsim from the Select an instrument pull-down menu. Select VISA Code Generation from the Code generation type pull-down menu. Click the Add Step button. Click Query and Parse to write and read from the Instrument Simulator. Enter *IDN? as the command. Click the Run this step button. If no error warning appears in the lower half of the dialog box, this step has successfully completed. Click the Separator(s) text box and delete its contents. To parse the data received, click the Auto parse button.

LabVIEW Introduction Course Manual

9-28

ni.com

Lesson 9

Instrument Control

Rename Token by typing ID String in the Token name text box. Click the Add Step button. Click Query and Parse. Enter MEASURE:VOLTAGE:DC? as the command. Click the Run this step button. To parse the data received, click the Auto parse button. The data returned is a random numeric value. Rename Token by typing Voltage in the Token name text box. The configuration window should be similar to Figure 9-22. Click the OK button to exit the I/O Assistant and return to the block diagram. 6. Create an indicator for the ID String. Right-click the ID String terminal and select CreateIndicator from the shortcut menu. 7. Create an indicator for the voltage. Right-click the Voltage terminal and select CreateIndicator from the shortcut menu. To allow LabVIEW to handle errors automatically, do not connect a Simple Error Handler VI to error out.
Tip

8. Display the front panel window. The front panel window should be similar in Figure 9-23.

Figure 9-23. GPIB IIOA A VI Front Panel Window

9. Save the VI.

National Instruments Corporation

9-29

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

10. Run the VI. Resize the string indicator if necessary. 11. Examine the code generated by the I/O Assistant. Right-click the I/O Assistant and select Open Front Panel. Click the Convert button when prompted to convert to a subVI. View the code generated by the I/O Assistant. Where is the command *IDN? written to the Instrument Simulator? Where is the voltage being read? Select FileClose to exit the subVI. Do not save changes. 12. Close the VI when finished.

End of Exercise 9-2

LabVIEW Introduction Course Manual

9-30

ni.com

Lesson 9

Instrument Control

G. Using VISA
VISA is the lower layer of functions in the LabVIEW instrument driver VIs that communicates with the driver software. VISA by itself does not provide instrumentation programming capability. VISA is a high-level API that calls low-level drivers. VISA can control VXI, GPIB, serial, or computer-based instruments and makes the appropriate driver calls depending on the type of instrument used. When debugging VISA problems, remember that an apparent VISA problem could be an installation problem with one of the drivers that VISA calls. In LabVIEW, VISA is a single library of functions you use to communicate with GPIB, serial, VXI, and computer-based instruments. You do not need to use separate I/O palettes to program an instrument. For example, some instruments give you a choice for the type of interface. If the LabVIEW instrument driver were written with functions on the FunctionsAll FunctionsInstrument I/OGPIB palette, those instrument driver VIs would not work for the instrument with the serial port interface. VISA solves this problem by providing a single set of functions that work for any type of interface. Therefore, many LabVIEW instrument drivers use VISA as the I/O language.

VISA Programming Terminology

The following terminology is similar to that used for instrument driver VIs: ResourceAny instrument in the system, including serial and parallel ports. SessionYou must open a VISA session to a resource to communicate with it, similar to a communication channel. When you open a session to a resource, LabVIEW returns a VISA session number, which is a unique refnum to that instrument. You must use the session number in all subsequent VISA functions. Instrument DescriptorExact name of a resource. The descriptor specifies the interface type (GPIB, VXI, ASRL), the address of the device (logical address or primary address), and the VISA session type (INSTR or Event).

The instrument descriptor is similar to a telephone number, the resource is similar to the person with whom you want to speak, and the session is similar to the telephone line. Each call uses its own line, and crossing these lines results in an error. Table 9-1 shows the proper syntax for the instrument descriptor.

National Instruments Corporation

9-31

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Table 9-1. Syntax for Various Instrument Interfaces

Interface Asynchronous serial GPIB VXI instrument through embedded or MXIbus controller GPIB-VXI controller

Syntax
ASRL[device][::INSTR] GPIB[device]::primary address[::secondary address][::INSTR] VXI[device]::VXI logical address[::INSTR] GPIB-VXI[device][::GPIB-VXI primary address]::VXI logical address[::INSTR]

You can use an alias you assign in MAX instead of the instrument descriptor. If you choose not to use the Instrument I/O Assistant to automatically generate code for you, you can still write a VI to communicate with the instrument. The most commonly used VISA communication functions are the VISA Write and VISA Read functions. Most instruments require you to send information in the form of a command or query before you can read information back from the instrument. Therefore, the VISA Write function is usually followed by a VISA Read function. The VISA Write and VISA Read functions work with any type of instrument communication and are the same whether you are doing GPIB or serial communication. However, because serial communication requires you to configure extra parameters, you must start the serial port communication with the VISA Configure Serial Port VI.

LabVIEW Introduction Course Manual

9-32

ni.com

Lesson 9

Instrument Control

VISA and Serial

The VISA Configure Serial Port VI initializes the port identified by VISA resource name to the specified settings. Timeout sets the timeout value for the serial communication. Baud rate, data bits, parity, and flow control specify those specific serial port parameters. The error in and error out clusters maintain the error conditions for this VI. Figure 9-24 shows how to send the identification query command *IDN? to the instrument connected to the COM2 serial port. The VISA Configure Serial Port VI opens communication with COM2 and sets it to 9,600 baud, eight data bits, odd parity, one stop bit, and XON/XOFF software handshaking. Then, the VISA Write function sends the command. The VISA Read function reads back up to 200 bytes into the read buffer, and the Simple Error Handler VI checks the error condition.

Figure 9-24. Configuring Serial for VISA Example Note

You also can use the VIs and functions located on the Serial palette for parallel port communication. You specify the VISA resource name as being one of the LPT ports. For example, you can use MAX to determine that LPT1 has a VISA resource name of ASRL10::INSTR.

National Instruments Corporation

9-33

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Exercise 9-3
Goal

VISA Write and Read VI

Communicate with a serial or GPIB interface to an instrument using VISA functions.

Description
This VI uses VISA to communicate with either a serial or a GPIB interface to an instrument. The VI can send one buffer of data to the instrument and read one buffer back. If using GPIB, the user specifies how many bytes to read from the bus. If using serial, the VI determines how many bytes are available, and reads them all. 1. Open the VISA Write and Read.vi in the <Exercises>\ LabVIEW Basics I\VISA Write & Read directory.

Figure 9-25. VISA Write and Read VI Front Panel

2. Open the block diagram of the VI and examine the code. The GPIB portion is shown in Figure 9-26.

Figure 9-26. GPIB Portion of the VISA Write and Read VI Block Diagram

LabVIEW Introduction Course Manual

9-34

ni.com

Lesson 9

Instrument Control

Select the exercise instructions that correspond to your instrument simulator and communication method from the following choices: NI Instrument Simulator A, serial communication, follow the instructions in the Test A: Serial with NI Instrument Simulator A section. NI Instrument Simulator A, GPIB communication, follow the instructions in the Test B: GPIB with NI Instrument Simulator A section. Instrument Simulator B, serial communication, follow the instructions in the Test C: Serial with NI Instrument Simulator B section. NI Instrument Simulator B, GPIB communication, follow the instructions in the Test D: GPIB with NI Instrument Simulator B section.

Test A: Serial with NI Instrument Simulator A

1. Configure the NI Instrument Simulator A to communicate through the serial port. It may still be set up from the last exercise. Power off the NI Instrument Simulator. Set the left bank of switches on the side of the box to match Figure 9-27.
1 2 3 OFF

ON

S Mode

Data Format

Baud Rate

Figure 9-27. Serial Configuration Settings for NI Instrument Simulator A

Make sure the NI Instrument Simulator is connected to a serial port. Power on the NI Instrument Simulator. Verify that the Power, Ready, and Listen LEDs are lit. 2. Enter values into the controls in preparation for communicating with the instrument. You do not need to enter a value in the byte count, as this control is only used for GPIB communication. Select the serial port in the VISA resource name control. Select Serial with NI Instrument Simulator A from the Hardware Type enumerated control.

National Instruments Corporation

9-35

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Enter *IDN?\n in the write buffer. 3. Run the VI. 4. The top of the instrument simulator lists other commands that are recognized by this instrument. Try other commands in this VI.

Test B: GPIB with NI Instrument Simulator A

1. Configure the NI Instrument Simulator A to communicate through the GPIB interface. Power off the NI Instrument Simulator. Set the left bank of switches on the side of the box to match Figure 9-28.
OFF

ON 1 2

GPIB Address Set the GPIB Address

G Mode GPIB Mode

Figure 9-28. GPIB Configuration Settings for NI Instrument Simulator A

Make sure the NI Instrument Simulator is connected to the GPIB device. Power on the NI Instrument Simulator. Verify that both the Power and Ready LEDs are lit. 2. Enter values into the controls in preparation for communicating with the instrument. Select devsim in the VISA resource name control. Select GPIB with NI Instrument Simulator A from the Hardware Type enumerated control. Enter *IDN? in the write buffer.
Note Press the <Enter> key after entering *IDN? to ensure that the end of line character \n appears in the string control.

LabVIEW Introduction Course Manual

9-36

ni.com

Lesson 9

Instrument Control

3. Run the VI. 4. The top of the instrument simulator lists other commands that are recognized by this instrument. Try other commands in this VI. 5. Close the VI when finished.

Test C: Serial with NI Instrument Simulator B

1. Verify that the Power and Ready LEDs are lit. 2. Enter values into the controls in preparation for communicating with the instrument. Select the serial port in the VISA resource name control. Select Serial with NI Instrument Simulator A from the Hardware Type enumerated control. Enter *IDN?\n in the write buffer. 3. Run the VI. 4. The NI Instrument Simulator Help lists other commands that are recognized by this instrument. Try other commands in this VI.

Test D: GPIB with NI Instrument Simulator B

1. Verify that the Power and Ready LEDs are lit. 2. Enter values into the controls in preparation for communicating with the instrument. Select devsim in the VISA resource name control. Select GPIB with NI Instrument Simulator B from the Hardware Type enumerated control. Enter *IDN? in the write buffer.
Note Press the <Enter> key after entering *IDN? to ensure that the end of line character \n appears in the string control.

3. Run the VI. 4. The NI Instrument Simulator Help lists other commands that are recognized by this instrument. Try other commands in this VI. 5. Close the VI when finished.

End of Exercise 9-3

National Instruments Corporation 9-37 LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

H. Using Instrument Drivers

Imagine the following scenario. You wrote a LabVIEW VI that communicates with a specific oscilloscope in your lab. Unfortunately, the oscilloscope no longer works, and you must replace it. However, this particular oscilloscope is no longer made. You found a different brand of oscilloscope that you want to purchase, but your VI no longer works with the new oscilloscope. You must rewrite your VI. When you use an instrument driver, the driver contains the code specific to the instrument. Therefore, if you change instruments, you must replace only the instrument driver VIs with the instrument driver VIs for the new instrument, which greatly reduces your redevelopment time. Instrument drivers help make test applications easier to maintain because the drivers contain all the I/O for an instrument in one library, separate from other code. When you upgrade hardware, upgrading the application is easier because the instrument driver contains all the code specific to that instrument.

Understanding Instrument Drivers

A LabVIEW Plug and Play instrument driver is a set of VIs that control a programmable instrument. Each VI corresponds to an instrument operation, such as configuring, triggering, and reading measurements from the instrument. Instrument drivers help users get started using instruments from a PC and saves them development time and cost because users do not need to learn the programming protocol for each instrument. With open-source, well documented instrument drivers, end users can customize their operation for better performance. A modular design makes the driver easier to customize.

Locating Instrument Drivers

You can locate most LabVIEW Plug and Play instrument drivers in the Instrument Driver Finder. You can access the Instrument Driver Finder within LabVIEW by selecting ToolsInstrumentationFind Instrument Drivers or HelpFind Instrument Drivers. The Instrument Driver Finder connects you with ni.com to find instrument drivers. When you install an instrument driver, an example program using the driver is added to the NI Example Finder.

LabVIEW Introduction Course Manual

9-38

ni.com

Lesson 9

Instrument Control

Example Instrument Driver VI

The block diagram in Figure 9-29 initializes the Agilent 34401 digital multimeter (DMM), uses a configuration VI to choose the resolution and range, select the function, and enable or disable auto range, uses a data VIs to read a single measurement, closes the instrument, and checks the error status. Every application that uses an instrument driver has a similar sequence of events: Initialize, Configure, Data, and Close.

Figure 9-29. Agilent 34401 DMM Instrument Driver Example

This is an example program that is available in the NI Example Finder when you install the LabVIEW Plug and Play instrument driver for the Agilent 34401 DMM.

Understanding Instrument Drivers

Many programmable instruments have a large number of functions and modes. With this complexity, it is necessary to provide a consistent design model that aids both instrument driver developers as well as end users who develop instrument control applications. The LabVIEW Plug and Play instrument driver model contains both external structure and internal structure guidelines. The external structure shows how the instrument driver interfaces with the user and to other software components in the system. The internal structure shows the internal organization of the instrument driver software module. For the external structure of the instrument driver, the user interacts with the instrument driver using an API or an interactive interface. Usually, the interactive interface is used for testing or for end-users. The API is accessed through LabVIEW. The instrument driver communicates with the instrument using VISA.

National Instruments Corporation

9-39

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Internally, the VIs in an instrument driver are organized into six categories. These categories are summarized in the following table. Category Initialize Description The initialize VI establishes communication with the instrument and is the first instrument driver VI called. Configure VIs are software routines that configure the instrument to perform specific operations. After calling these VIs, the instrument is ready to take measurements or stimulate a system. Action/Status VIs command the instrument to carry out an action (i.e. arming a trigger) or obtain the current status of the instrument or pending operations. The data VIs transfer data to or from the instrument. Utility VIs perform a variety of auxiliary operations, such as reset and self-test. The close VI terminates the software connection to the instrument. This is the last instrument driver VI called.

Configure

Action/Status

Data Utility Close

LabVIEW Introduction Course Manual

9-40

ni.com

Lesson 9

Instrument Control

Exercise 9-4
Goal

Concept: NI Devsim VI
Install an instrument driver and explore the example programs that accompany the instrument driver.

Description
Install the instrument driver for the NI Instrument Simulator. After installation, explore the VIs that the instrument driver provides and the example programs that are added to the NI Example Finder. Select the exercise instructions that correspond to your instrument simulator the following choices: NI Instrument Simulator A, follow the instructions in Part A: NI Instrument Simulator A. NI Instrument Simulator B, follow the instructions in Part B: NI Instrument Simulator B.

Part A: NI Instrument Simulator A Install Instrument Driver

1. Exit LabVIEW. 2. Navigate to the <Exercises>\LabVIEW Basics I\Instrument Driver directory. This folder contains the LabVIEW Plug and Play instrument drivers for the Instrument Simulator. 3. Double-click the NI Instrument Simulator A Zip folder to extract the contents. 4. Extract to the C:\Program Files\National Instruments\ LabVIEW 8.5\instr.lib directory.

Explore Instrument Driver

5. Start LabVIEW. 6. Open a blank VI. 7. Switch to the block diagram. 8. Navigate to the NI Instrument Simulator category of the Functions palette. 9. Explore the palette using the Context Help window to familiarize yourself with the functionality.

National Instruments Corporation

9-41

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Use Example Programs

10. Select HelpFind Examples to start the NI Example Finder. 11. Confirm that you are browsing according to task. 12. Navigate to Hardware Input and OutputInstrument Drivers LabVIEW Plug and Play in the task structure. 13. Double-click NI Instrument Simulator Read DMM Measurement.vi to open the example program. This VI reads a single measurement from the Instrument Simulator. 14. Prepare the Instrument Simulator. This VI can communicate with the instrument through serial or GPIB. To communicate through serial, set the Instrument Simulator switches as shown in Figure 9-30.
1 2 3 OFF

ON

S Mode

Data Format

Baud Rate

Figure 9-30. Serial Configuration Settings for NI Instrument Simulator A

To communicate through GPIB, set the Instrument Simulator switches as shown in Figure 9-31.
OFF

ON 1 2

GPIB Address Set the GPIB Address

G Mode GPIB Mode

Figure 9-31. GPIB Configuration Settings for NI Instrument Simulator A

LabVIEW Introduction Course Manual

9-42

ni.com

Lesson 9

Instrument Control

15. Select the communication type on the VISA Resource Name control. If you are using serial, select the resource (COM1 or COM2) that the serial cable is connected to. If you are using GPIB, select the devsim VISA alias. 16. Run the VI. 17. Explore the block diagram of the VI. Do not save changes. 18. Close the VI. 19. Return to the NI Example Finder. 20. Double-click NI Instrument Simulator Read Oscilloscope Waveform.vi to open the next example program. This VI reads a single waveform from the Instrument Simulator. 21. Select the same VISA Resource Name you selected in step 15. 22. Run the VI. 23. Choose a different Waveform Function. 24. Run the VI again. 25. Explore the block diagram of the VI. 26. Close the VI and the NI Example Finder when you are finished. Do not save changes.

Part B: NI Instrument Simulator B Install Instrument Driver

1. Exit LabVIEW. 2. Navigate to the <Exercises>\LabVIEW Basics I\Instrument Driver directory. This folder contains the LabVIEW Plug and Play instrument drivers for the Instrument Simulator. 3. Double-click the NI Instrument Simulator B Zip folder to extract the contents. 4. Extract to the C:\Program Files\National Instruments\ LabVIEW 8.5\instr.lib directory.

National Instruments Corporation

9-43

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Explore Instrument Driver

5. Start LabVIEW. 6. Open a blank VI. 7. Switch to the block diagram. 8. Navigate to the NI Instrument Simulator category of the Functions palette. 9. Explore the palette using the Context Help window to familiarize yourself with the functionality.

Use Example Programs

10. Select HelpFind Examples to start the NI Example Finder. 11. Confirm that you are browsing according to task. 12. Navigate to Hardware Input and OutputInstrument Drivers LabVIEW Plug and Play in the task structure. 13. Double-click NI Instrument Simulator Read Measurement(Multimeter).vi to open the example program. This VI reads a single measurement from the Instrument Simulator. 14. Verify that the Power and Ready LEDs are lit on the NI Instrument Simulator. This VI can communicate with the instrument through serial or GPIB. 15. Select the communication type on the VISA Resource Name control. If you are using serial, select the resource (COM1 or COM2) that the serial cable is connected to. If you are using GPIB, select the devsim VISA alias. 16. Run the VI. 17. Explore the block diagram of the VI. Do not save changes. 18. Close the VI. 19. Return to the NI Example Finder. 20. Double-click NI Instrument Simulator Read Waveform(Oscilloscope).vi to open the next example program. This VI reads a single waveform from the Instrument Simulator.

LabVIEW Introduction Course Manual

9-44

ni.com

Lesson 9

Instrument Control

21. Select the same VISA Resource Name you selected in step 15. 22. Run the VI. 23. Choose a different Waveform Function. 24. Run the VI again. 25. Explore the block diagram of the VI. 26. Close the VI and the NI Example Finder when you are finished. Do not save changes.

End of Exercise 9-4

National Instruments Corporation

9-45

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Self Review: Quiz

1. Which instrument interface does not use the VISA API? a. Serial b. DAQ c. GPIB d. Ethernet 2. What API does the Instrument I/O Assistant use? a. C b. Visual Basic c. VISA d. NI-DAQmx 3. Which of the following is a way to inform listeners that all data has been transferred? a. Asserting the End or Identify (EOI) line. b. Placing a end-of-string (EOS) character at the beginning of the data being transferred. c. Using the VISA Close function. d. Turning off the power to the controller.

National Instruments Corporation

9-47

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Self Review: Quiz Answers

1. Which instrument interface does not use the VISA API? a. Serial b. DAQ c. GPIB d. Ethernet 2. What API does the Instrument I/O Assistant use? a. C b. Visual Basic c. VISA d. NIDAQmx 3. Which of the following is a way to inform listeners that all data has been transferred? a. Asserting the End or Identify (EOI) line. b. Placing a end-of-string (EOS) character at the beginning of the data being transferred. c. Using the VISA Close function. d. Turning off the power to the controller.

National Instruments Corporation

9-49

LabVIEW Introduction Course Manual

Lesson 9

Instrument Control

Notes

LabVIEW Introduction Course Manual

9-50

ni.com

Common Design Techniques and Patterns

10

The first step in developing a LabVIEW project is to explore the architectures that exist within LabVIEW. Architectures are essential for creating a successful software design. The most common architectures are usually grouped into design patterns. As a design pattern gains acceptance, it becomes easier to recognize when a design pattern has been used. This recognition helps you and other developers read and modify VIs that are based on design patterns. There are many design patterns for LabVIEW VIs. Most applications use at least one design pattern. In this course, you explore the State Machine design pattern. Learn more about design patterns in the LabVIEW Basics II: Development course.

Topics
A. Using Sequential Programming B. Using State Programming C. State Machines D. Using Parallelism

National Instruments Corporation

10-1

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

A. Using Sequential Programming

In Lesson 1, Problem Solving, you designed a flowchart for a Temperature Weather Station. The Temperature Weather Station VI completes the following steps: 1. Read the temperature 2. Test the temperature for limits and display warnings 3. Graph and log the temperature After you reach the end of the sequence of steps, you check to see if the stop button has been clicked, and, if not, the sequence repeats. Many of the VIs you write in LabVIEW accomplish sequential tasks. How you program these sequential task can be very different. Consider the block diagram in Figure 10-1. In this block diagram, a voltage signal is acquired, a dialog box prompts the user to turn on the power, the voltage signal is acquired again, and the user is prompted to turn off the power. However, in this example, there is nothing in the block diagram to force the execution order of these events. Any one of these events could happen first.

Figure 10-1. Unsequenced Tasks

In LabVIEW, you can complete sequential tasks by placing each task in a separate subVI, and wiring the subVIs in the order you want the to execute using the error cluster wires. However, in this example, only two of the tasks have a error cluster. Using the error clusters, you can force the execution order of the two DAQ Assistants, but not the One Button Dialog functions, as shown in Figure 10-2.

LabVIEW Introduction Course Manual

10-2

ni.com

Lesson 10

Common Design Techniques and Patterns

Figure 10-2. Partially Sequenced Tasks

You can use a Sequence structure to force the order of operations of block diagram objects. A Sequence structure contains one or more subdiagrams, or frames, that execute in sequential order; a frame cannot begin execution until everything in the previous frame has completed execution. Figure 10-3 shows an example of this VI using a Sequence structure to force execution order.

Figure 10-3. Tasks Sequenced with a Sequence Structure

To take advantage of the inherent parallelism in LabVIEW, avoid overusing Sequence structures. Sequence structures guarantee the order of execution, but prohibit parallel operations. Another negative to using Sequence structures is that you cannot stop the execution part way through the sequence. A good way to use Sequence structures for this example is shown in Figure 10-4.

National Instruments Corporation

10-3

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Figure 10-4. Tasks Sequenced with Sequence Structures and an Error Cluster

The best way to write this VI, however, is to enclose the One Button Dialog functions in a Case structure, and wire the error cluster to the case selector. Use Sequence structures sparingly because the hide code. Rely on data flow rather than sequence structures to control the order of execution.

Figure 10-5. Tasks Sequenced with an Error Cluster and Case Structures

LabVIEW Introduction Course Manual

10-4

ni.com

Lesson 10

Common Design Techniques and Patterns

B. Using State Programming

Although a Sequence structure and sequentially wired subVIs both accomplish the task, often your VIs require more complex programming: What if you must change the order of the sequence? What if you must repeat an item in the sequence more often than the other items? What if some items in the sequence execute only when certain conditions are met? What if you must stop the program immediately, rather than waiting until the end of the sequence?

Although your program may not have any of the above requirements, there is always the possibility that the program must be modified in the future. For this reason, a state programming architecture is a good choice, even if a sequential programming structure would be sufficient.

C. State Machines
The state machine design pattern is a common and very useful design pattern for LabVIEW. You can use the state machine design pattern to implement any algorithm that can be explicitly described by a state diagram or flowchart. A state machine usually implements a moderately complex decision-making algorithm, such as a diagnostic routine or a process monitor. A state machine, which is more precisely defined as a finite state machine, consists of a set of states and a transition function that maps to the next state. Finite state machines have many variations. The two most common finite state machines are the Mealy machine and the Moore machine. A Mealy machine performs an action for each transition. A Moore machine performs a specific action for each state in the state transition diagram. The state machine design pattern template in LabVIEW implements any algorithm described by a Moore machine.

Applying State Machines

Use state machines in applications where distinguishable states exist. Each state can lead to one or multiple states or end the process flow. A state machine relies on user input or in-state calculation to determine which state to go to next. Many applications require an initialization state, followed by a default state, where many different actions can be performed. The actions performed can depend on previous and current inputs and states. A shutdown state commonly performs clean up actions.

National Instruments Corporation

10-5

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

State machines are commonly used to create user interfaces. In a user interface, different user actions send the user interface into different processing segments. Each processing segment acts as a state in the state machine. Each segment can lead to another segment for further processing or wait for another user action. In a user interface application, the state machine constantly monitors the user for the next action to take. Process testing is another common application of the state machine design pattern. For a process test, a state represents each segment of the process. Depending on the result of each states test, a different state might be called. This can happen continually, resulting in an in-depth analysis of the process you are testing. The advantage of using a state machine is that after you have created a state transition diagram, you can create LabVIEW VIs easily.

State Machine Infrastructure

Translating the state transition diagram into a LabVIEW block diagram requires the following infrastructure components: While LoopContinually executes the various states Case StructureContains a case for each state and the code to execute for each state Shift RegisterContains state transition information State Functionality CodeImplements the function of the state Transition CodeDetermines the next state in the sequence

Figure 10-6 shows the basic structure of a state machine implemented in LabVIEW for a temperature data acquisition system.

While Loop

Shift Register

Case Structure

Figure 10-6. Basic Infrastructure of a LabVIEW State Machine

LabVIEW Introduction Course Manual

10-6

ni.com

Lesson 10

Common Design Techniques and Patterns

The flow of the state transition diagram is implemented by the While Loop. The individual states are represented by cases in the Case structure. A shift register on the While Loop keeps track of the current state and communicates the current state to the Case structure input.

Controlling State Machines

The best method for controlling the initialization and transition of state machines is the enumerated type control. Enums are widely used as case selectors in state machines. However, if the user attempts to add or delete a state from the enumerated type control, the remaining wires that are connected to the copies of this enumerated type control break. This is one of the most common obstacles when implementing state machines with enumerated type controls. One solution to this problem is to create a type defined enumerated type control. This causes all the enumerated type control copies to automatically update if you add or remove a state.

Transitioning State Machines

There are many ways to control what case a Case structure executes in a state machine. Choose the method that best suits the function and complexity of your state machine. Of the methods to implement transitions in state machines, the most common and easy to use is the single Case structure transition code, which can be used to transition between any number of states. This method provides for the most scalable, readable, and maintainable state machine architecture. The other methods can be useful in specific situations, and it is important for you to be familiar with them.

Default Transition
For the default transition, no code is needed to determine the next state, because there is only one possible state that occurs next. Figure 10-7 shows a design pattern that uses a default transition implemented for a temperature data acquisition system.

Figure 10-7. Single Default Transition

National Instruments Corporation

10-7

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Transition Between Two States

The following method involves making a decision on a transition between two states. There are several patterns commonly used to accomplish this. Figure 10-8 shows the Select function used to transition between two states.

Figure 10-8. Select Function Transition Code

This method works well if you know that the individual state always transitions between two states. However, this method limits the scalability of the application. If you need to modify the state to transition among more than two states, this solution would not work and would require a major modification of the transition code.

Transition Among Two or More States

Create a more scalable architecture by using one of the following methods to transition among states. Case StructureUse a Case structure instead of the Select function for the transition code. Figure 10-9 shows the Case structure transition implemented for a temperature data acquisition system.

Figure 10-9. Case Structure Transition Code

One advantage to using a Case structure is that the code is self-documenting. Because each case in the Case structure corresponds

LabVIEW Introduction Course Manual

10-8

ni.com

Lesson 10

Common Design Techniques and Patterns

to an item in the enum, it is easy to read and understand the code. A Case structure also is scalable. As the application grows, you can add more transitions to a particular state by adding more cases to the Case structure for that state. A disadvantage to using a Case structure is that not all the code is visible at once. Because of the nature of the Case structure, it is not possible to see at a glance the complete functionality of the transition code. Transition ArrayIf you need more of the code to be visible than a Case structure allows, you can create a transition array for all the transitions that can take place. Figure 10-10 shows the transition array implemented for a temperature data acquisition system.

Figure 10-10. Transition Array Transition Code

In this example, the decision making code provides the index that describes the next state. For example, if the code should progress to the Error Handler state next, the decision making code outputs the number 1 to the index input of the Index Array function. This design pattern makes the transition code scalable and easy to read. One disadvantage of this pattern is that you must use caution when developing the transition code because the array is zero-indexed. State Diagram ToolkitAnother pattern that implements the transition code is also used by the NI LabVIEW State Diagram Toolkit. This pattern uses a large Case structure for every state and a smaller While Loop that iterates through the state transitions until the proper state transition is met. Figure 10-11 shows the LabVIEW State Diagram Toolkit implementation for a temperature data acquisition system. The LabVIEW State Diagram Toolkit adds the State Diagram Editor function to LabVIEW to visually draw the logic that defines an application. As this visual representation of the logic is created, the State Diagram Editor generates the LabVIEW code that acts as the foundation of your application.

National Instruments Corporation

10-9

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Note The LabVIEW State Diagram Toolkit is not included in the LabVIEW Professional Development System, it is available for purchase separately.

Figure 10-11. State Diagram Toolkit State Machine

The following conditions must exist in the State Diagram Toolkit state machine: There must always be a default transition. The default transition must always have lowest priority so it is evaluated last. The default transition condition must always be TRUE. You can wire a Boolean constant to the condition output for the default transition.

LabVIEW Introduction Course Manual

10-10

ni.com

Lesson 10

Common Design Techniques and Patterns

Case Study: Course Project

The course project acquires a temperature every half second, analyzes each temperature to determine if the temperature is too high or too low, and alerts the user if there is a danger of heatstroke or freeze. The program logs the data if a warning occurs. If the user has not clicked the stop button, the entire process repeats. Figure 10-12 shows the state transition diagram for the course project.

Initialize

Acquistion

Time Elapsed = TRUE and Stop = FALSE

Analysis

Warning = TRUE Datalog

Time Elapsed = FALSE and Stop = FALSE Time Check Warning = FALSE

Stop = TRUE

Figure 10-12. State Transition Diagram for the Course Project

Figures 10-13 through 10-16 illustrate the states of the state machine that implements the state transition diagram detailed in Figure 10-12. If you have installed the exercises and solutions, the project is located in the <Exercises>\LabVIEW Basics I\Course Project directory, and you can further explore this state machine.
National Instruments Corporation 10-11 LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Figure 10-13. Acquisition State

Figure 10-14. Analysis State

LabVIEW Introduction Course Manual

10-12

ni.com

Lesson 10

Common Design Techniques and Patterns

Figure 10-15. Data Log State

Figure 10-16. Time Check State

National Instruments Corporation

10-13

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Exercise 10-1 State Machine VI

Goal
Create a VI that implements a state machine using a type-defined enum.

Scenario
You must design a template for a user interface state machine. The state machine must allow the user to activate Process 1 or Process 2 in any order. The state machine must also allow for expansion, because processes may be added in the future.

Design Inputs and Outputs

Table 10-1. Inputs and Outputs

Type Cancel Button Cancel Button Stop Button

Name
Process 1

Properties Boolean Text:

Process 1

Process 2

Boolean Text:
Process 2

Stop

State Transitions
Table 10-2. Inputs and Outputs

State Idle

Action Poll user interface for selection

Next State No button clicked: Idle State Process 1 clicked: Process 1 State Process 2 clicked: Process 2 State Stop clicked: Stop State Idle State Idle State Stop State

Process 1 Process 2 Stop

Execute Process 1 code Execute Process 2 code Stop the state machine

LabVIEW Introduction Course Manual

10-14

ni.com

Lesson 10

Common Design Techniques and Patterns

Implementation
In the following steps, you will create the front panel window shown in Figure 10-17.

Figure 10-17. State Machine VI Front Panel Window

1. Create a new project containing a blank VI. Select Empty Project from the Getting Started window. Select FileSave Project. Name the project State Machine.lvproj in the <Exercises>\ LabVIEW Basics I\State Machine directory. Select FileNew VI. Save the new VI as State Machine.vi in the <Exercises>\ LabVIEW Basics I\State Machine directory. 2. Create a menu cluster containing buttons for running process 1, running process 2, and stopping the VI. Place a cluster shell on the front panel window. Relabel the cluster Menu. Add a cancel button to the cluster shell. Relabel the cancel button Process 1. Change the Boolean text Run Process 1. Make a copy of the Process 1 button, and place the copy within the cluster shell. Rename the copied button Process 2. Change the Boolean text on the copied button to Run Process 2.

National Instruments Corporation

10-15

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Right-click each button and select Visible ItemsLabel to hide the labels. Add a stop button to the cluster shell. Right-click the Stop button and select Visible ItemsLabel to hide the label. Modify the Boolean text on the buttons using the Text Settings on the toolbar. Suggested text settings: 24 point bold Application Font. Enlarge and arrange the buttons within the cluster using the resizing tool and the following toolbar buttons: Align Objects, Distribute Objects, and Resize Objects. Right-click the cluster and select AutosizingSize to Fit. Right-click the cluster and select Visible ItemsLabel to hide the label. 3. Create the type-defined enum to control the state machine. Add an enum to the front panel window. Right-click the enum and select Edit Items. Modify the list as follows: Items
Idle Process 1 Process 2 Stop

Digital Display 0 1 2 3

Select OK to exit the Enum Properties dialog box. Relabel the enum control State Enum. Right-click the State Enum and select AdvancedCustomize. Select Type Def. from the Control Type pull-down menu. Right-click the Enum and select RepresentationU32.

LabVIEW Introduction Course Manual

10-16

ni.com

Lesson 10

Common Design Techniques and Patterns

Save the control as State Enum.ctl in the <Exercises>\ LabVIEW Basics I\State Machine directory. Close the Control Editor window. Click Yes when asked if you would like to replace the control. Switch to the block diagram. Right-click the State Enum and select Change to Constant. The enumerate control no longer appears on the front panel window. In the following steps, you create the block diagram shown in Figure 10-18. This block diagram contains four statesIdle, Process 1, Process 2 and Stop.

Figure 10-18. Idle State

4. Create the block diagram shown in Figure 10-18. Use the following tips to assist you: Wire the enum to the Case structure using a shift register on the While Loop. After you wire the enumerated constant to the case selector terminal of the Case structure, right-click the Case structure and select Add Case for Every Value to automatically add a case for each item in the enum. Copy the enum to use within the Case structure. The copy is also linked to the type-defined enum. Wire a False constant to the conditional terminal; the state machine should not stop from the Idle state.

National Instruments Corporation

10-17

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

In the Idle state, you convert the cluster to an array so that the array can be searched for any button clicked. The Search 1D Array function returns the index of the button clicked. Because the Idle State does not have a button associated with it, this index must be incremented by one. Use the Type Cast function to select the appropriate item from the enum constant. It is very important that the order of the cluster matches the order of the items in the enumerated constant.

Figure 10-19. Process 1 State

5. Complete the Process 1 state shown in Figure 10-19. Use the following tips to assist you: Use a One Button Dialog function to simulate the Process 1 code. Wire a False constant to the conditional terminal; the state machine should not stop from Process 1 state.

LabVIEW Introduction Course Manual

10-18

ni.com

Lesson 10

Common Design Techniques and Patterns

Figure 10-20. Process 2 State

6. Complete the Process 2 state shown in Figure 10-20. Use the following tips to assist you: Use a One Button Dialog function to simulate the Process 2 code. Wire a False constant to the conditional terminal; the state machine should not stop from the Process 2 state.

Figure 10-21. Stop State

7. Complete the Stop state shown in Figure 10-21. Use the following tips to assist you: Pass a True constant to the conditional terminal; the state machine should stop only from this state. 8. Save the VI when you have finished.

National Instruments Corporation

10-19

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Test
1. Switch to the front panel window. 2. Run the VI. Experiment with the VI to be sure it works as expected. If it does not, compare your block diagram to Figures 10-18 through 10-21. 3. Save and close the VI when you are finished.

End of Exercise 10-1

LabVIEW Introduction Course Manual

10-20

ni.com

Lesson 10

Common Design Techniques and Patterns

D. Using Parallelism
Often, you need to program multiple tasks so that they execute at the same time. In LabVIEW tasks can run in parallel if they do not have a data dependency between them, and if they are not using the same shared resource. An example of a shared resource is a file, or an instrument. You learn about LabVIEW design patterns for executing multiple tasks at the same time in the LabVIEW Basics II: Development course. These design patterns include parallel loops, master/slave, and producer/consumer.

National Instruments Corporation

10-21

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Summary
Using a state machine instead of a sequential programming structure provides the following benefits: You can change the order of the sequence. You can repeat individual items in the sequence. You can set a condition to determine when an item in the sequence should execute. You can stop the program at any point in the sequence.

LabVIEW Introduction Course Manual

10-22

ni.com

Lesson 10

Common Design Techniques and Patterns

Notes

National Instruments Corporation

10-23

LabVIEW Introduction Course Manual

Lesson 10

Common Design Techniques and Patterns

Notes

LabVIEW Introduction Course Manual

10-24

ni.com

Analyzing and Processing Numeric Data

Users generally start their work by acquiring data into an application or program, because their tasks typically require interaction with physical processes. In order to extract valuable information from that data, make decisions on the process, and obtain results, the data needs to be manipulated and analyzed. As an engineering-focused tool, LabVIEW makes hundreds of analysis functions available for researchers, scientists, and engineers, as well as students and professors. They can build these functions right into their applications to make intelligent measurements and obtain results faster.

Topics
A. Choosing the Correct Method for Analysis B. Analysis Categories

National Instruments Corporation

A-1

LabVIEW Introduction Course Manual

Appendix A

Analyzing and Processing Numeric Data

A. Choosing the Correct Method for Analysis

Users incorporate analysis into their applications and programs in different ways. There are certain considerations that help determine the way in which analysis should be performed.

Inline versus Offline Analysis

Inline analysis implies that the data is analyzed within the same application where it is acquired. This is generally the case when dealing with applications where decisions have to be made during run time and the results have direct consequences on the process, typically through the changing of parameters or executing of actions. This is typically the case in control applications. When dealing with inline analysis, it is important to consider the amount of data acquired and the particular analysis routines that are performed on that data. A proper balance must be found because they could easily become computationally intensive and have an adverse effect on the performance of the application. Other examples for inline analysis are applications where the parameters of the measurement need to be adapted to the characteristics of the measured signal. One case is where one or more signals need to be logged, but these change very slowly except for sudden bursts of high-speed activity. In order to reduce the amount of data logged, the application would have to quickly recognize the need for a higher sampling rate, and reduce it when the burst is over. By measuring and analyzing certain aspects of the signals the application can adapt to the circumstances and enable the appropriate execution parameters. Although this is only one example, there are thousands of applications where a certain degree of intelligencethe ability to make decisions based on various conditionsand adaptability are required, which can only be provided by adding analysis algorithms to the application. Decisions based on acquired data are not always made in an automated manner. Very frequently, those involved with the process need to monitor the execution and determine whether it is performing as expected or if one or more variables need to be adjusted. Although it is not uncommon for users to log data, extract it from a file or database and then analyze it offline to modify the process, many times the changes need to happen during run time. In these cases, the application must handle the data coming from the process, and then manipulate, simplify, format, and present the data in a way that it is most useful to the user. LabVIEW users can then take advantage of the many visualization objects to present that data in the most concise and useful manner. LabVIEW offers analysis and mathematical routines that natively work together with data acquisition functions and display capabilities, so that they

LabVIEW Introduction Course Manual

A-2

ni.com

Appendix A

Analyzing and Processing Numeric Data

can be easily built into any application. In addition, LabVIEW offers analysis routines for point-by-point execution; these routines are designed specifically to meet the needs of inline analysis in real-time applications. Users should consider certain aspects when deciding whether point-by-point routines are appropriate. Offline applications dont typically have the demand for results to be obtained in real-time fashion in order to make decisions on the process. Offline analysis applications require only that sufficient computational resources are available. The main intent of such applications is to identify cause and effect of variables affecting a process by correlating multiple data sets. These applications generally require importing data from custom binary or ASCII files and commercial databases such as Oracle, Access, and other SQL/ODBC-enabled databases. Once the data is imported into LabVIEW, users perform several or hundreds of available analysis routines, manipulate the data, and arrange it in a specific format for reporting purposes. LabVIEW provides functions to access any type of file format and database, seamlessly connect to powerful reporting tools such as NI DIAdem and the Report Generation Toolkit for Microsoft Office, and execute the latest data-sharing technologies such as XML, Web-enabled data presentation, and ActiveX.

Programmatic versus Interactive Analysis

As LabVIEW users, scientists and engineers are very familiar with the many ways in which they can acquire data from hundreds of devices. They build intelligence into their applications to perform inline analysis and present results while the applications are running. In addition, they are aware that acquiring data and processing it for the sake of online visualization is not enough. Users typically store hundreds or thousands of megabytes of data in hard drives and data bases. After anywhere from one to hundreds of runs of the application, users proceed to extract information in order to make decisions, compare results, and make appropriate changes to the process, until the desired results are achieved. It is relatively easy to acquire amounts of data so large that it rapidly becomes unmanageable. In fact, with a fast DAQ board and enough channels, it may only take a few milliseconds to compile thousands of values. It is not a trivial task to make sense out of all that data. Engineers and scientists are typically expected to present reports, create graphs, and ultimately corroborate any assessments and conclusions with empirical data. Without the right tools, this can easily become a daunting task, resulting in lost productivity. In order to simplify the process of analyzing measurements, LabVIEW programmers create applications that provide dialogs and interfaces that others can use so that depending on their input, specific analysis routines are

National Instruments Corporation

A-3

LabVIEW Introduction Course Manual

Appendix A

Analyzing and Processing Numeric Data

performed on any given data set. By building this type of application, users build a certain degree of interactivity into their applications. For this to be efficient, the programmer must have extensive knowledge about the information and the types of analysis in which the user is interested. With LabVIEW, you can easily perform significant data reduction and formatting before storing it to disk, so that when the stored data is retrieved for further analysis, it is easier to handle. LabVIEW also provides hundreds of functions for generating reports based on the results and information obtained from the acquired data.

B. Analysis Categories
LabVIEW offers hundreds of built-in analysis functions that cover different areas and methods of extracting information from acquired data. You can use these functions as is, or modify, customize, and extend them to suit a particular need. These functions are categorized in the following groups: Measurement, Signal Processing, Mathematics, Image Processing, Control, Simulation, and Application Areas. Measurement Amplitude and Level Frequency (Spectral) Analysis Noise and Distortion Pulse and Transition Signal and Waveform Generation Time Domain Analysis Tone Measurements Digital Filters Convolution and Correlation Frequency Domain Joint Time-Frequency Analysis (Signal Processing Toolset) Sampling/Resampling Signal Generation Super-Resolution Spectral Analysis (Signal Processing Toolset) Transforms Time Domain Wavelet and Filter Bank Design (Signal Processing Toolset) Windowing

Signal Processing

LabVIEW Introduction Course Manual

A-4

ni.com

Appendix A

Analyzing and Processing Numeric Data

Mathematics Basic Math Curve Fitting and Data Modeling Differential Equations Interpolation and Extrapolation Linear Algebra Nonlinear Systems Optimization Root Finding Special Functions Statistics and Random Processes Blob Analysis and Morphology Color Pattern Matching Filters High-Level Machine Vision Tools High-Speed Grayscale Pattern Matching Image Analysis Image and Pixel Manipulation Image Processing Optical Character Recognition Region-of-Interest Tools PID and Fuzzy Control Simulation Simulation Interface (Simulation Interface Toolkit) Machine Condition Monitoring (Order Analysis Toolset) Machine Vision (IMAQ, Vision Builder) Motion Control Sound and Vibration (Sound and Vibration Analysis Toolset)

Image Processing

Control

Application Areas

For a complete list of LabVIEW analysis functions refer to ni.com/ analysis.

National Instruments Corporation

A-5

LabVIEW Introduction Course Manual

Appendix A

Analyzing and Processing Numeric Data

Exercise A-1
Goal

Concept: Analysis Types

Choose when to use inline, offline, programmatic, or interactive analysis for an application.

Description
For each scenario, determine which form(s) of analysis to use. Most scenarios use more than one form.

Scenario 1
The failure rate of your manufacturing line is related directly to the speed of production. You need to monitor the failure rate programmatically. If the failure rate is greater than 3%, decrease the speed of the line. If the failure rate is less than 2%, increase the speed of the line.
Inline Offline Programmatic Interactive

Scenario 2
You are listening to a radio station. The frequency components of the radio station signal are determined and recorded to file. If you have difficulty hearing the radio station, you tell the VI to pass the signal through a filter before recording the data.
Inline Offline Programmatic Interactive

Scenario 3
You are recording temperature and pressure data. Once a week, you prepare a report for your manager correlating the temperature and pressure trends during thunderstorms.
Inline Offline Programmatic Interactive

Scenario 4
You are performing stress analysis on a bridge. During rush hour, you must also record vibration data on the bridge. It is considered rush hour when more than 100 cars use the bridge in 5 minutes. A sensor records the number of cars crossing the bridge.
Inline Offline Programmatic Interactive

Refer to the following page for answers to these scenarios.

LabVIEW Introduction Course Manual

A-6

ni.com

Appendix A

Analyzing and Processing Numeric Data

Scenario 1
Inline Analysis Programmatic Analysis

Inline analysis determines the speed of the line and the failure rate. Programmatic analysis determines when to change the speed of the line.

Scenario 2
Inline Analysis Interactive Analysis

The user tells the VI when to apply the filter, which means the analysis is interactive. However, because the filtering happens immediately when the user specifies, the analysis is inline.

Scenario 3
Offline Analysis The data can be correlated at any point and does not need to occur as the data is acquired. When it is analyzed, it is usually analyzed programmatically. However, without more information, you cannot determine whether programmatic or interactive analysis is appropriate.

Scenario 4
Programmatic Analysis The VI uses the sensor to determine when rush hour is occurring and immediately begins recording the additional data. Since no information is given on how the data is analyzed, you cannot determine whether inline or offline analysis is appropriate.

End of Exercise A-1

National Instruments Corporation

A-7

LabVIEW Introduction Course Manual

Appendix A

Analyzing and Processing Numeric Data

Notes

LabVIEW Introduction Course Manual

A-8

ni.com

Measurement Fundamentals

This appendix explains concepts that are critical to acquiring and generating signals effectively. These concepts focus on understanding the parts of your measurement system that exist outside the computer. You will learn about transducers, signal sources, signal conditioning, grounding of your measurement system, and ways to increase the quality of your measurement acquisition. This lesson provides basic understanding of these concepts.

Topics
A. Using Computer-Based Measurement Systems B. Understanding Measurement Concepts C. Increasing Measurement Quality

National Instruments Corporation

B-1

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

A. Using Computer-Based Measurement Systems

The fundamental task of all measurement systems is the measurement and/or generation of real-world physical signals. Measurement devices help you acquire, analyze, and present the measurements you take. An example of a measurement system is shown in Figure B-1. Before a computer-based measurement system can measure a physical signal, such as temperature, a sensor or transducer must convert the physical signal into an electrical one, such as voltage or current. You may need to condition the electrical signal to obtain a better measurement of the signal. Signal conditioning may include filtering to remove noise or applying gain or attenuation to the signal to bring it into an acceptable measurement range. After conditioning the signal, measure the signal and communicate the measurement to the computer. This course teaches two methods of communicating the measured electrical signal to the computerwith a data acquisition (DAQ) device or with a stand-alone instrument (instrument control). Software controls the overall system, which includes acquiring the raw data, analyzing the data, and presenting the results. With these building blocks, you can obtain the physical phenomenon you want to measure into the computer for analysis and presentation.

LabVIEW Introduction Course Manual

B-2

ni.com

Appendix B

Measurement Fundamentals

Physical Phenomenon Light, Pressure, Temperature, etc. Sensors and Transducers

+ V

+ HV

+ mV

Signal Conditioning

Signal Conditioning

SC-2

345

MAINFR

SCX I
AME

Data Acquisition (DAQ) Board

Stand-alone Instrument

ON

STAND BY

6 7 8

GPIB Board/Serial Port/Other Communication

Driver Engines/API NI-DAQmx, NI-DAQmx Base

Driver Engines/API NI-488.2, NI-VISA, NI-Serial

Application Software LabVIEW, LabWindows/CVI, Measurement Studio, or Other Programming Environments

Figure B-1. Measurement System Overview

B. Understanding Measurement Concepts

This section introduces you to concepts you should be familiar with before taking measurements with a DAQ device and instruments.

Signal Acquisition
Signal acquisition is the process of converting physical phenomena into data the computer can use. A measurement starts with using a transducer to convert a physical phenomenon into an electrical signal. Transducers can generate electrical signals to measure such things as temperature, force, sound, or light. Table B-1 lists some common transducers.

National Instruments Corporation

B-3

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

Table B-1. Phenomena and Transducers

Phenomena Temperature

Transducer Thermocouples Resistance temperature detectors (RTDs) Thermistors Integrated circuit sensors Vacuum tube photosensors Photoconductive cells Microphones Strain gages Piezoelectric transducers Load cells Potentiometers Linear voltage differential transformers (LVDT) Optical encoders Head meters Rotational flowmeters Ultrasonic flowmeters pH electrodes

Light Sound Force and pressure

Position (displacement) Fluid flow

pH

Signal Sources
Analog input acquisitions use grounded and floating signal sources.

Grounded Signal Sources

A grounded signal source is one in which the voltage signals are referenced to a system ground, such as the earth or a building ground, as shown in Figure B-2. Because such sources use the system ground, they share a common ground with the measurement device. The most common examples of grounded sources are devices that plug into a building ground through wall outlets, such as signal generators and power supplies.

LabVIEW Introduction Course Manual

B-4

ni.com

Appendix B

Measurement Fundamentals

Vs

Ground

Figure B-2. Grounded Signal Source

Note The grounds of two independently grounded signal sources generally are not at the same potential. The difference in ground potential between two instruments connected to the same building ground system is typically 10 mV to 200 mV. The difference can be higher if power distribution circuits are not properly connected. This causes a phenomenon known as a ground loop.

Floating Signal Sources

In a floating signal source, the voltage signal is not referenced to any common ground, such as the earth or a building ground, as shown in Figure B-3. Some common examples of floating signal sources are batteries, thermocouples, transformers, and isolation amplifiers. Notice in Figure B-3 that neither terminal of the source is connected to the electrical outlet ground as in Figure B-2. Each terminal is independent of the system ground.

Vs

Ground

Figure B-3. Floating Signal Source

Signal Conditioning
Signal conditioning is the process of measuring and manipulating signals to improve accuracy, isolation, filtering, and so on. Many stand-alone instruments and DAQ devices have built-in signal conditioning. Signal conditioning also can be applied externally by designing a circuit to condition the signal or by using devices specifically made for signal conditioning. National Instruments has SCXI devices and other devices that are designed for this purpose. Throughout this section, different DAQ and SCXI devices illustrate signal conditioning topics.

National Instruments Corporation

B-5

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

To measure signals from transducers, you must convert them into a form a measurement device can accept. For example, the output voltage of most thermocouples is very small and susceptible to noise. Therefore, you might need to amplify the thermocouple output before you digitize it. This amplification is a form of signal conditioning. Common types of signal conditioning include amplification, linearization, transducer excitation, and isolation. Figure B-4 shows some common types of transducers and signals and the signal conditioning each requires.

Transducers/Signals Thermocouples

Signal Conditioning Amplification, Linearization, and Cold-Junction Compensation Current Excitation, Four-Wire and Three-Wire Configuration, Linearization Voltage Excitation, Bridge Configuration, and Linearization Isolation Amplifiers (Optical Isolation) Electromechanical Relays or Solid-State Relays

RTDs

Strain Gages

Common Mode or High Voltages Loads Requiring AC Switching or Large Current Flow Signals with High Frequency Noise

DAQ Device

Lowpass Filters

Figure B-4. Common Transducers and Signal Conditioning Types

Amplification
Amplification is the most common type of signal conditioning. Amplifying electrical signals improves accuracy in the resulting digitized signal and reduces the effects of noise. Amplify signals as close to the signal source as possible. Amplifying a signal near the device also amplifies any noise that attached to the signal. Amplifying near the signal source results in the largest signal-to-noise ratio (SNR). For the highest possible accuracy, amplify the signal so the maximum voltage range equals the maximum input range of the analog-to-digital converter (ADC).

LabVIEW Introduction Course Manual

B-6

ni.com

Appendix B

Measurement Fundamentals

Noise Instrumentaion Amplifier

+ Low-Level Signal

MUX Lead Wires External Amplifier ADC

DAQ Device

Figure B-5. Signal Amplification

If you amplify the signal at the DAQ device while digitizing and measuring the signal, noise might have entered the lead wire, which decreases SNR. However, if you amplify the signal close to the signal source with a SCXI module, noise has a less destructive effect on the signal, and the digitized representation is a better reflection of the original low-level signal. Refer to the National Instruments Web site at ni.com/info and enter the info code exd2hc for more information about analog signals.

Linearization
Many transducers, such as thermocouples, have a nonlinear response to changes in the physical phenomena you measure. LabVIEW can linearize the voltage levels from transducers so you can scale the voltages to the measured phenomena. LabVIEW provides scaling functions to convert voltages from strain gages, RTDs, thermocouples, and thermistors.

Transducer Excitation
Signal conditioning systems can generate excitation, which some transducers require for operation. Strain gages and RTDs require external voltage and currents, respectively, to excite their circuitry into measuring physical phenomena. This type of excitation is similar to a radio that needs power to receive and decode audio signals.

Isolation
Another common way to use signal conditioning is to isolate the transducer signals from the computer for safety purposes.
Caution When the signal you monitor contains large voltage spikes that could damage the computer or harm the operator, do not connect the signal directly to a DAQ device without some type of isolation.

You also can use isolation to ensure that differences in ground potentials do not affect measurements from the DAQ device. When you do not reference the DAQ device and the signal to the same ground potential, a ground loop

National Instruments Corporation

B-7

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

can occur. Ground loops can cause an inaccurate representation of the measured signal. If the potential difference between the signal ground and the DAQ device ground is large, damage can occur to the measuring system. Isolating the signal eliminates the ground loop and ensures that the signals are accurately measured.

Measurement Systems
You configure a measurement system based on the hardware you use and the measurement you acquire.

Differential Measurement Systems

Differential measurement systems are similar to floating signal sources in that you make the measurement with respect to a floating ground that is different from the measurement system ground. Neither of the inputs of a differential measurement system are tied to a fixed reference, such as the earth or a building ground. Handheld, battery-powered instruments and DAQ devices with instrumentation amplifiers are examples of differential measurement systems. A typical National Instruments device uses an implementation of an eight-channel differential measurement system as shown in Figure B-6. Using analog multiplexers in the signal path increases the number of measurement channels when only one instrumentation amplifier exists. In Figure B-6, the AIGND (analog input ground) pin is the measurement system ground.

LabVIEW Introduction Course Manual

B-8

ni.com

Appendix B

Measurement Fundamentals

MUX CH0+ CH1+ CH2+

CH7+

Instrumentation Amplifier +

MUX CH0 CH1 CH2

Vm

CH7

AIGND

Figure B-6. Typical Differential Measurement System

Referenced and Non-Referenced Single Ended

Referenced and non-referenced single-ended measurement systems are similar to grounded sources in that you make the measurement with respect to a ground. A referenced single-ended measurement system measures voltage with respect to the ground, AIGND, which is directly connected to the measurement system ground. Figure B-7 shows a 16-channel referenced single-ended measurement system.

National Instruments Corporation

B-9

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

MUX CH0 CH1 CH2

Instrumentation Amplifier +

CH15

Vm

AIGND

Figure B-7. Typical Referenced Single-Ended (RSE) Measurement System

DAQ devices often use a non-referenced single-ended (NRSE) measurement technique, or pseudodifferential measurement, which is a variant of the referenced single-ended measurement technique. Figure B-8 shows a NRSE system.
MUX CH0+ CH1+ CH2+

Instrumentation Amplifier +

CH15+

Vm

AISENSE AIGND

Figure B-8. Typical Non-Referenced Single-Ended (NRSE) Measurement System

In a NRSE measurement system, all measurements are still made with respect to a single-node analog input sense (AISENSE on E Series devices), but the potential at this node can vary with respect to the measurement system ground (AIGND). A single-channel NRSE measurement system is the same as a single-channel differential measurement system.

LabVIEW Introduction Course Manual

B-10

ni.com

Appendix B

Measurement Fundamentals

Signal Sources and Measurement Systems Summary

Figure B-9 summarizes ways to connect a signal source to a measurement system.
Signal Source Type Floating Signal Source (Not Connected to Building Ground) Grounded Signal Source

Input

Examples Ungrounded Thermocouples Signal Conditioning with Isolated Outputs Battery Devices

Examples Plug-in Instruments with Nonisolated Outputs

ACH(+)

+ V 1 Differential (DIFF)

ACH(+)

ACH()

+ V 1

ACH()

R AIGND AIGND

See text for information on bias resistors. NOT RECOMMENDED

ACH

Single-Ended Ground Referenced (RSE)

+ V 1

ACH

AIGND

+ V 1
+ Vg

AIGND

Ground-loop losses, Vg, are added to measured signal.

ACH ACH

+ V 1 Single-Ended Nonreferenced (NRSE)

AISENSE

+ V 1

AISENSE

AIGND

AIGND

See text for information on bias resistors.

Figure B-9. Signal Source and Measurement Systems Summary

National Instruments Corporation

B-11

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

C. Increasing Measurement Quality

When you design a measurement system, you may find that the measurement quality does not meet your expectations. You might want to record the smallest possible change in a voltage level. Perhaps you cannot tell if a signal is a triangle wave or a sawtooth wave and would like to see a better representation of the shape of a signal. Often, you want to reduce the noise in the signal. This section introduces methods for achieving these three increases in quality.

Achieving Smallest Detectable Change

The following factors affect the amount of detectable change in a voltage signal: The resolution and range of the ADC The gain applied by the instrumentation amplifier The combination of the resolution, range, and gain to calculate a property called the code width value

Resolution
Resolution is the smallest amount of input signal change that a device or sensor can detect. The number of bits used to represent an analog signal determines the resolution of the ADC. You can compare the resolution on a measurement device to the marks on a ruler. The more marks you have, the more precise your measurements. Similarly, the higher the resolution, the higher the number of divisions into which your system can break down the ADC range, and therefore, the smaller the detectable change. A 3-bit ADC divides the range into 23 or 8 divisions. A binary or digital code between 000 and 111 represents each division. The ADC translates each measurement of the analog signal to one of the digital divisions. The following figure shows a sine wave digital image as obtained by a 3-bit ADC. Clearly, the digital signal does not represent the original signal adequately, because the converter has too few digital divisions to represent the varying voltages of the analog signal. By increasing the resolution to 16 bits, however, the number of divisions of the ADC increases from 8 to 65,536 (216). The ADC now can obtain an extremely accurate representation of the analog signal.

LabVIEW Introduction Course Manual

B-12

ni.com

Appendix B

Measurement Fundamentals

10.00 8.75 7.50 6.25 5.00 3.75 2.50 1.25 0 0

111 110 101 100 011 010 001 000

16-bit

Amplitude (V)

3-bit

50

100 Time ( s)

150

200

Figure B-10. 3-Bit and 16-Bit Resolution Example

Device Range
Device range refers to the minimum and maximum analog signal levels that the ADC can digitize. Many measurement devices can select from several ranges (typically 0 to 10 V or 10 to 10 V), by changing from unipolar mode to bipolar mode or by selecting from multiple gains, allowing the ADC to take full advantage of its resolution to digitize the signal. Unipolar and Bipolar Modes Unipolar mode means that a device only supports a range of 0 V to +X V. Bipolar mode means that a device supports a range of X V to +X V. Some devices support only one mode or the other, while other devices can change from unipolar mode to bipolar mode. Devices that can change from unipolar to bipolar mode are able to select the mode that best fits the signal to measure. Chart 1 in Figure B-11 illustrates unipolar mode for a 3-bit ADC. The ADC has eight digital divisions in the range from 0 to 10 V. In bipolar mode, the range is 10.00 to 10.00 V, as shown in chart 2. The same ADC now separates a 20 V range into eight divisions. The smallest detectable difference in voltage increases from 1.25 to 2.50 V, and you now have a much less accurate representation of the signal. The device selects the best mode available based on the input limits you specify when you create a virtual channel.

National Instruments Corporation

B-13

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

1 10.00 8.75 7.50 6.25 5.00 3.75 2.50 1.25 0 0

111

2 10.00 7.50 5.00 2.50 0 2.50 5.00 7.50 10.00 0

111 110 101 100 011 010 001 000

Amplitude (V)

101 100 011 010 001 000

50

100

150

200

Amplitude (V)

110

50

100

150

200

Range = 0 to 10 V

Range = 10 to 10 V

Figure B-11. Range Example

Amplification
Amplification or attenuation of a signal can occur before the signal is digitized to improve the representation of the signal. By amplifying or attenuating a signal, you can effectively decrease the input range of an ADC and thus allow the ADC to use as many of the available digital divisions as possible to represent the signal. For example, Figure B-12 shows the effects of applying amplification to a signal that fluctuates between 0 and 5 V using a 3-bit ADC and a range of 0 to 10 V. With no amplification, or gain = 1, the ADC uses only four of the eight divisions in the conversion. By amplifying the signal by two before digitizing, the ADC uses all eight digital divisions, and the digital representation is much more accurate. Effectively, the device has an allowable input range of 0 to 5 V because any signal above 5 V, when amplified by a factor of two, makes the input to the ADC greater than 10 V.
10.00 8.75 7.5 6.25 V 5.00 3.75 2.50 1.25 0.00 sec Gain = 1 Gain = 2

111 110 101 100 011 010 001 000 Gain = 2 Gain = 1

Figure B-12. Amplification Example

LabVIEW Introduction Course Manual

B-14

ni.com

Appendix B

Measurement Fundamentals

The range, resolution, and amplification available on a DAQ device determine the smallest detectable change in the input voltage. This change in voltage represents one least significant bit (LSB) of the digital value and is also called the code width.

Code Width
Code width is the smallest change in a signal that a system can detect. Calculate code width using the following formula: 1 C = D ---------R (2 ) Where C is code width, D is device input range, and R is bits of resolution. Device input range is a combination of the gain applied to the signal and the input range of the ADC. For example, if the ADC input range is 10 to +10 V peak to peak and the gain is 2, the device input range is 5 to +5 V peak to peak, or 10 V. The smaller the code width, the more accurately a device can represent the signal. The formula confirms what you have already learned in the discussion on resolution, range, and gain: Larger resolution = smaller code width = more accurate representation of the signal Larger amplification = smaller code width = more accurate representation of the signal Larger range = larger code width = less accurate representation of the signal

Determining the code width is important in selecting a DAQ device. For example, a 12-bit DAQ device with a 0 to 10 V input range and an amplification of one detects a 2.4 mV change, while the same device with a 10 to 10 V input range would detect a change of 4.8 mV. 1 1 C = D ---------- = 10 ----------- = 2.4mV R 12 (2 ) (2 ) 1 1 C = D ---------- = 20 ----------- = 4.8mV R 12 (2 ) (2 )

National Instruments Corporation

B-15

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

Increasing Shape Recovery

The most effective way of increasing the shape recovery of a signal is to reduce your code width and increase your sampling frequency. To measure the frequency of your signal effectively, you must sample the signal at least at the Nyquist frequency. The Nyquist Theorem states that you must sample a signal at a rate greater than twice the highest frequency component of interest in the signal to capture the highest frequency component of interest. Otherwise, the high-frequency content aliases at a frequency inside the spectrum of interest, called the pass-band. The following formula illustrates the Nyquist Theorem: f sampling > 2 f signal Where fsampling is the sampling rate, and fsignal is the highest frequency component of interest in the measured signal. To determine how fast to sample, refer to Figure B-13, which shows the effects of various sampling rates. In case A, the sine wave of frequency f is sampled at the same frequency f. The reconstructed waveform appears as an alias at DC. However, if you increase the sampling rate to 2f, the digitized waveform has the correct frequency (same number of cycles) but appears as a triangle waveform. In this case f is equal to the Nyquist frequency. By increasing the sampling rate to well above f, for example 5f, you can more 4f accurately reproduce the waveform. In case C the sampling rate is at ---3 The Nyquist frequency in this case is ( 4f ) 3 = 2f ------------------2 3 Because f is larger than the Nyquist frequency, this sampling rate reproduces an alias waveform of incorrect frequency and shape. The faster the sample, the better the shape recovery of the signal. However, available hardware often limits the sampling rate.

LabVIEW Introduction Course Manual

B-16

ni.com

Appendix B

Measurement Fundamentals

A
Sampled at

B
Sampled at 2

C
Sampled at 4/3

Figure B-13. Effects of Sampling Rates

Decreasing Noise
To reduce noise take the following precautions: Use shielded cables or a twisted pair of cables. Minimize wire length to minimize noise the lead wires pick up. Keep signal wires away from AC power cables and monitors to reduce 50 or 60 Hz noise. Increase the SNR ratio by amplifying the signal close to the signal source. Acquire data at a higher frequency than necessary, then average the data to reduce the impact of the noise, as noise tends to average to zero.

National Instruments Corporation

B-17

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

Exercise B-1
Goal

Concepts: Measurement Fundamentals

Understand how resolution, voltage range, gain, and aliasing affect a measured signal.

Description
1. Open Resolution.vi in the <Exercises>\LabVIEW Basics I\ Measurement Fundamentals directory. This VI simulates the acquisition of a sine wave and the digitization that occurs with an analog to digital convertor (ADC). This VI contains the following controls and indicators: Input Signal VoltageThis input specifies the range of the signal being acquired. The default value of the control is 1 Volt. This means that the range of the signal is 2 Vvoltage between the highest point of the signal and the lowest point of the signal. Resolution (ADC)This input specifies the resolution of the ADC of the data acquisition device used to acquire the signal. The default value of the control is 3 bits. Device Input RangeThis input incorporates the input range of the ADC and the gain applied to the signal. The default value of the control is 1 Volts. This peak to peak voltage is equivalent to 2 V. Because the input range of the ADC is 10 V, this means that there is a gain of 10 applied to the signal. Code WidthThis output calculates the code width using the current values of the controls, where C is code width, D is device input range, and R is bits of resolution: 11 C = D ---------- = 2 --------- = 0.25V R 3 (2 ) (2 )

LabVIEW Introduction Course Manual

B-18

ni.com

Appendix B

Measurement Fundamentals

2. Run the VI and experiment with the values of the controls.

Figure B-14. Resolution VI Front Panel

Click the Run button to run the VI. Leave the default settings for the controls. The red plot demonstrates the actual input sinewave. The white plot demonstrates the output of the ADC. Notice that the white plot is a poor representation of the signal. You can see the code width of .25 V shown on the graph representing only 8 discrete levels. Change the Resolution (ADC). Notice that the signal representation quality increases as you increase the ADC resolution. Set the resolution to 3 bits. Change the Device Input Range. Notice that when the range is too large, the resolution is not efficiently divided among the signal range. When the input range is too small, part of the signal is cut off. Experiment further with different control values until you understand the importance of each input. It is important to ensure that the input signal range is as close to the device input range as possible.

National Instruments Corporation

B-19

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

3. Using the Resolution VI, determine the code width of an input signal that varies between 0.8 V using a DAQ device with a resolution of 16 bits. Assume that gain is efficiently applied. Code Width: 4. Determine the code width of an input signal that varies between 10 V using a DAQ device with a resolution of 8 bits. The device input range is set to 10 V. Code Width: 5. If the device input range is 1 V, and the resolution is 12 bits, what is the largest input signal you can read without cutting off the input signal? Input Signal Range: 6. Stop and close the VI when you are finished. 7. Open Aliasing.vi in the <Exercises>\LabVIEW Basics I\ Measurement Fundamentals directory. This VI simulates the acquisition of a waveform at a specific sampling frequency. As you adjust the sampling frequency and the frequency of the acquired waveform, you can observe the Nyquist Theorem in effect. This VI contains the following controls: Original Signal FrequencyThis input specifies the frequency of the signal being acquired. You can increase or decrease this frequency by turning the knob. Sampled WaveformThe input allows you to choose between a sine wave or a square wave. Use the sine wave input to experiment with the Nyquist Theorem, and the square wave to understand how the sampling frequency affects shape recovery. Sampling Rate (Hz)This input specifies the rate at which the DAQ device takes a sample of the acquired signal. According to the Nyquist Theorem, this rate should be at least twice the frequency of the sampled signal.

Sampled Signal

LabVIEW Introduction Course Manual

B-20

ni.com

Appendix B

Measurement Fundamentals

8. Run the VI and experiment with the values of the controls until the acquired frequency is wrong.

Figure B-15. Aliasing VI Front Panel

Set the Waveform Type to Sine. Set the Sampling Rate Hz to 10 MS/s (megasamples per second). Adjust the Frequency of the Sampled Signal, starting at the lowest frequency, and moving up until the frequency reported on the top chart is no longer correct. Notice how the Sampled plot becomes more distorted as you increase the Frequency of the Sampled Signal. After you have passed the Nyquist frequency (5 MHz in this case), the frequency recorded is no longer correct. This is an example of aliasing. 9. Try other values for the controls using a sine wave. 10. Set the Waveform Type to Square. Modify the controls to see how shape recovery is affected by the sampling frequency and the frequency of the signal. 11. Stop and close the VI when you are finished.

End of Exercise B-1

National Instruments Corporation

B-21

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

Self-Review: Quiz
1. Calculate the code width for signal acquired using a 16 bit DAQ device with a device input range of 5 V.

2. You are acquiring a triangle wave with a frequency of 1100 Hz. Which sampling frequency should you use for best shape recovery of the signal? a. 1 kHz b. 10 kHz c. 100 kHz d. 1000 kHz 3. You are acquiring a triangle wave with a frequency of 1100 Hz. You can sample the signal at the following rates. Which is the minimum sampling frequency you should use to reliably acquire the frequency of the signal? a. 1 kHz b. 10 kHz c. 100 kHz d. 1000 kHz

National Instruments Corporation

B-23

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

Self-Review: Quiz Answers

1. Calculate the code width for signal acquired using a 16 bit DAQ device with a device input range of 5 V. 1 1 C = D ---------- = 5 ----------- = 76.29V R 16 (2 ) (2 ) 2. You are acquiring a triangle wave with a frequency of 1100 Hz. Which sampling frequency should you use for best shape recovery of the signal? a. 1 kHz b. 10 kHz c. 100 kHz d. 1000 kHz 3. You are acquiring a triangle wave with a frequency of 1100 Hz. You can sample the signal at the following rates. Which is the minimum sampling frequency you should use to reliably acquire the frequency of the signal? a. 1 kHz b. 10 kHz c. 100 kHz d. 1000 kHz

National Instruments Corporation

B-25

LabVIEW Introduction Course Manual

Appendix B

Measurement Fundamentals

Notes

LabVIEW Introduction Course Manual

B-26

ni.com

CAN: Controller Area Network

A Controller Area Network (CAN) bus is a high-integrity serial bus system for networking intelligent devices. CAN busses and devices are common components in automotive and industrial systems. Using a CAN interface device, you can write LabVIEW applications to communicate with a CAN network.

Topics
A. History of CAN B. CAN Basics C. Channel Configuration D. CAN APIs E. CAN Programming in LabVIEW (Channel API)

National Instruments Corporation

C-1

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

A. History of CAN
In the past few decades, the need for improvements in automotive technology caused increased usage of electronic control systems for functions such as engine timing, anti-lock brake systems, and distributorless ignition. Originally, point-to-point wiring systems connected electronic devices in vehicles. More and more electronics in vehicles resulted in bulky wire harnesses that were heavy and expensive. To eliminate point-to-point wiring, automotive manufacturers replaced dedicated wiring with in-vehicle networks, which reduced wiring cost, complexity, and weight. In 1985, Bosch developed the Controller Area Network (CAN), which has emerged as the standard in-vehicle network. CAN provides a cheap, durable network that allows the devices to speak through the Electronic Control Unit (ECU). CAN allows the ECU to have one CAN interface rather than analog inputs to every device in the system. This decreases overall cost and weight in automobiles. Each of the devices on the network has a CAN controller chip and is therefore intelligent. All transmitted messages are seen by all devices on the network. Each device can decide if the message is relevant or if it can be filtered. As CAN implementations increased in the automotive industry, CAN (high speed) was standardized internationally as ISO 11898. Later, low-speed CAN was introduced for car body electronics. Finally, single-wire CAN was introduced for some body and comfort devices. Major semiconductor manufacturers such as Intel, Motorola, and Philips developed CAN chips. By the mid-1990s, CAN was the basis of many industrial device networking protocols, including DeviceNet and CANOpen.

Automotive Applications
Examples of CAN devices include engine controller (ECU), transmission, ABS, lights, power windows, power steering, instrument panel, and so on.

Automotive CAN Devices Instrument Panel Power Steering Power Windows Transmission Lights ABS

Figure C-1. Automotive CAN Devices

LabVIEW Introduction Course Manual

C-2

ni.com

Appendix C

CAN: Controller Area Network

Other CAN Markets

Comparing the requirements for automotive and industrial device networks showed the following similarities: the transition away from dedicated signal lines low cost resistance to harsh environments real-time capabilities

These similarities led to the use of CAN in industrial applications such as textile machinery, packaging machines, and production line equipment such as photoelectric sensors and motion. With its growing popularity in automotive and industrial applications, CAN has been increasingly used in a wide variety of applications. Usage in systems such as agricultural equipment, nautical machinery, medical apparatus, semiconductor manufacturing equipment, avionics, and machine tools validate the versatility of CAN.

Military Systems

Public Transportation

CAN Farm Machinery Avionics

Other Applications Including Medical Devices Printing Machines

Figure C-2. Other CAN Markets

National Instruments Corporation

C-3

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

B. CAN Basics
Benefits of CAN
Lower cost from reduced wiring compared to two wire, point-to-point wiring Highly robust protocol Built-in determinism Fault tolerance ReliableMore than a decade of use in the automotive industry

CAN Specifications
CAN data (up to 8 bytes in a frame) Maximum 1 Mbaud/s 40 Meters at 1 Mbaud/s 6 km at 10 kbaud/s Theoretical maximum of 2,032 nodes per bus Practical limit is approximately 100 nodes due to transceiver Most buses use 310 nodes Indicates message priority

Data fieldsArbitration ID (11 bit or 29 bit)

Types of CAN
High Speed CAN Up to 1 M bits/s transmission rate Up to 125 kbaud/s transmission rate Fault tolerant Up to 83.3 kbaud/s High-voltage pulse to wakeup sleeping devices Low Speed/Fault-Tolerant CAN

Single Wire

NI CAN Interface Devices

National Instruments provides four types of CAN interface devices that use the NI-CAN API described in this appendix. Each category of devices supports multiple form factors and is available in one or two port varieties.

LabVIEW Introduction Course Manual

C-4

ni.com

Appendix C

CAN: Controller Area Network

High-speed CAN 1 and 2 ports Maximum baud rate of 1Mb/s

Low-speed CAN 1 and 2 ports Maximum baud rate of 125 kbaud/s

Software Selectable CAN 1 and 2 ports (each port can be used as high-speed, low-speed, or single-wire CAN)

Single Wire CAN 1 and 2 ports Maximum baud rate of 83.3 kbaud/s

CAN Frame
CAN devices send data across the CAN Network on packets called frames. A typical CAN frame contains an arbitration ID, a data field, a remote frame, an error frame, and an overload frame.

Standard Frame Format

S O F 11-Bit Arbitration ID R I T D R E DLC 08 Data Bytes A 16-Bit CRC C K End of Frame

Extended Frame Format

S High 11-Bits O F of Arbitration ID R I Low 10-Bits T D E of Arbitration ID R DLC 08 Data Bytes A 16-Bit CRC C K End of Frame

Figure C-3. Standard and Extended CAN Frames

Arbitration ID
The arbitration ID determines the priority of the messages on the bus. If multiple nodes try to transmit a message onto the CAN bus at the same time, the node with the highest priority (lowest arbitration ID) automatically gets bus access. Nodes with a lower priority must wait until the bus becomes available before trying to transmit again. The waiting devices wait until the end of the frame section is detected.

National Instruments Corporation

C-5

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Device A transmits ID = 110 0100 0111 (647 hex) Device B transmits ID = 110 1100 0111 (6C7 hex)

1 1

0 0

0 0 0

1 1 1

1 1

0 1

Device B loses and goes idle until end of frame Device A wins, and proceeds

Figure C-4. CAN Arbitration

Data Field
The data field contains the actual data being transmitted. The CAN protocol supports two data field formats as defined in the Bosch Version 2.0 specifications, the essential difference being in the length of the arbitration ID. In the standard frame format (also known as 2.0A), the length of the ID is 11 bits. In the extended frame format (also known as 2.0B), the length of the ID is 29 bits. In NI-CAN terminology, a data field for which the individual fields are described is called a message. A message can contain one or more channels, which contain the data and other relevant information. In Figure C-5, the ABS message contains two channelsTemperature and Torque.
Message Overview: 0 1 2 3 4 5 6 7 CAN Data Frame 0 x 85 Temperature 4 bytes Arbitration ID RPMs 2 bytes 7 7 15 23 31 7 15 6 6 14 22 30 6 14 5 5 13 21 29 5 13 4 4 12 20 28 4 12 3 3 11 19 27 3 11 2 2 10 18 26 2 10 1 1 9 17 25 1 9 0 0 8 16 24 0 8

Data Field (8 bytes)

Figure C-5. CAN Message with Two Channels.

LabVIEW Introduction Course Manual

C-6

ni.com

Appendix C

CAN: Controller Area Network

Exercise C-0
Goal

Concept: CAN Device Setup

Connect CAN hardware and use MAX to view and test a CAN device.

Description
The exercises in this appendix use a 2-port CAN interface device and a CAN Demo Box. In this exercise, you set up your hardware, observe the configuration of the CAN device in MAX, and run a self-test to verify that the device functions correctly. 1. Connect the CAN hardware. Connect Port 1 on your CAN interface to the CAN input on the CAN Demo Box using a CAN cable. Connect the cable from your DAQ device to the 68-pin terminal on the CAN Demo Box. Use a wire to connect the following terminals on the CAN Demo Box. Gen terminal of the Function Generator Ch 0 terminal of the Analog In to CAN

2. Explore the CAN device and ports in MAX. Launch MAX. Expand Devices and Interfaces. The PCI-CAN/2 device is your CAN Interface Device. Expand PCI-CAN/2. CAN0 and CAN1 are physical ports on your CAN device. A single port interface has only one item.

National Instruments Corporation

C-7

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Select CAN0 and click the Properties button to display the Port Properties dialog box.

Figure C-6. Port Properties Dialog Box

Note

The Port Properties dialog box allows you to change the baud rate and other properties of the CAN Interface. The settings are already correct for the current configuration. You also can access the Port Properties dialog box by right-clicking a port and selecting Properties from the shortcut menu. Click OK to close the dialog box. 3. Test the CAN Interface Device. Select PCI-CAN/2 and observe the value of the Test Status property. The Test Status property displays Untested until you execute a self-test. Click the Self-test button located above the list of properties. Observe the value of the Test Status property after the test completes. Also notice that a small blue circle with a white check appears above the bottom right corner of the PCI-CAN/2 icon in the Configuration tree, indicating that the device has passed the self-test.

End of Exercise C-0

LabVIEW Introduction Course Manual

C-8

ni.com

Appendix C

CAN: Controller Area Network

C. Channel Configuration
You can configure Channels in MAX to enable LabVIEW to interpret your data fields. MAX allows you to load a set of channels from a database file or configure channels manually.

CAN Databases
To translate the data field into usable data, a CAN device comes with a database that describes the channels contained in the message. A CAN Database File (CANdb File) is a text file that contains this information. It allows you to find the data in a frame and convert it to engineering units. For each channel, CAN databases store the following data:
Channel name Location (Start bit) and size (number of bits) of the Channel within a given Message Byte Order (Intel/Motorola) Data type (signed, unsigned, and IEEE float) Scaling and units string Range Default Value Comment

With many software programs, you must manually convert the data field to usable data using the information contained in the database file. However, using National Instruments software, this conversion is done for you. You can load the channel configuration from the file into MAX, and then use it in your application through the NI-CAN driver.

Loading Channels From a Database

To import channel configurations from a Vector CANdb file into MAX, right-click the CAN Channels heading and select Import from CANdb File. <Shift>-click to select multiple channels, then select Import. If you need to select another set, you can select the channels and then import them again. When you finish importing, click Done to return to MAX.
Note You also can access a CAN database directly from the LabVIEW CAN API. However, loading the channels into MAX prevents you from having to specify a path in your LabVIEW programs and allows you to read and write from the channels using the MAX test panels.

National Instruments Corporation

C-9

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Figure C-7. Importing a CAN Database File In MAX

Explicitly Creating a Channel

If no database file exists, you can create channels in MAX. Complete the following steps to create channels within MAX: 1. Right-click the CAN Channels heading under Data Neighborhood and select Create Message. 2. Enter the message properties and click OK. After the message is created, it appears under CAN Channels. 3. Right-click the message name and select Create Channel. A configuration box appears similar to the one shown in Figure C-8. As you enter information about Start Bit and No. of Bits, the matrix is populated with dimmed boxes to indicate the bits that have already been used in channel definitions for that message. Blue boxes indicate the bits that are currently being defined.

LabVIEW Introduction Course Manual

C-10

ni.com

Appendix C

CAN: Controller Area Network

Figure C-8. Explicit Channel Configuration in MAX

4. Enter the channel properties and click the OK button. 5. Right-click and select Create Channel again for each channel contained in the message. 6. To save channel configurations to a file, right-click the CAN Channels heading and select Save Channel Configuration. Saving the channel configuration creates a custom database file for your device. The resulting NI-CAN database file uses file extension .ncd. You can access the NI-CAN database just like any other CAN database. By installing the NI-CAN database file along with your application, you can deploy your application to a variety of users. You can also test explicitly created channels using the Channel Test Panel.

National Instruments Corporation

C-11

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Exercise C-1
Goal

Channel Configuration
Learn how to load and test channels in MAX.

Description
Load channels from either an NI CAN database file or a Vector CAN Database file into MAX. Investigate the properties of messages and channels. Read data on a specific channel using MAX Test Panels. Finally, use the built-in CAN Bus Monitor feature in MAX to monitor the frame data being sent along the CAN bus. 1. Launch MAX and expand Data Neighborhood. 2. Load the database file for the CAN Demo Box. Right-click CAN Channels and select Import from CANdb File.

Navigate to <Exercises>\LabVIEW Basics I\CAN\ CAN Demo Box.dbc. You could choose to import the .ndc database files instead. To do so, select Load Channel Configuration instead of Import from CAN db File.
Tip

Select Add All Messages and Channels.

LabVIEW Introduction Course Manual

C-12

ni.com

Appendix C

CAN: Controller Area Network

Click Import. Click Done. 3. Test a channel in MAX Expand CAN Channels. A list of messages with predefined channels appears. Use these channels to communicate with your CAN Demo Box through your CAN Interface. Expand the message WAVEFORM0_SAW0_SWITCHES_FROM_CDB (0x710) to see the channels in that message, as shown in Figure C-9.

Figure C-9. WAVEFORM0_SAW0_SWITCHES_FROM_CDB (0x710) Message

Select the AnalogInToCANCh0 channel. Click the Test Panel button. You also can right-click the channel name and select Test Panel from the shortcut menu.
Tip

Click the Read tab if it is not already selected.

National Instruments Corporation

C-13

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Click the Start button to begin reading continuously. If the test panel is already reading when you open it, the start button is disabled and you do not need to click it.

Tip A periodic signal should appear. You can see the signal better by changing the scaling to Auto.

Experiment with changing the settings on the demo box itself. Use the Menu Select button to scroll through the different options. Click the Menu Select button until you see Func Gen Output. Click the <+> and <-> buttons to change which type of signal the Function Generator outputs. Select from the following choicesSine, Square, and Triangle. The screen displays which type is currently being output. Click the Menu Select button again until you see Func Gen Freq. Click the <+> and <-> buttons to increase and decrease the frequency of the signal the Function Generator outputs.

Click the Stop button in the MAX test panel to finish reading. Click the Close button to exit the Test Panel. 4. Monitor the CAN bus Expand My SystemDevices and InterfacesPCI-CAN/2. If selected, the device properties display in the window to the right. Expand PCI-CAN/2 and select CAN0. On the right, notice a list of attributes.

LabVIEW Introduction Course Manual

C-14

ni.com

Appendix C

CAN: Controller Area Network

Click the Bus Monitor button located above the attributes. Click the Start button to begin monitoring the CAN bus. If monitoring is already active, a Stop button appears in place of the Start button and you need not click a button.

Figure C-10. NI-CAN Bus Monitor

Unplug the connector between the CAN Interface and your demo box. The monitor ceases to show any transmissions because there is nothing being sent to or from the bus. Plug in the connector between the CAN Interface and your demo box. Notice periodic transmissions because the demo box is constantly transmitting to and receiving from the CAN Interface. Click the Stop button. Click the Reset button. 5. Save the bus monitor activity to file. Click the Options button. Place a checkmark in the Stream To Disk checkbox. Leave the remaining options at their default values. To specify where to stream the data, click the File Name button in the dialog box and navigate to a file path.

National Instruments Corporation

C-15

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Click the OK button. Click the Start button to begin monitoring and logging. After a few moments, click the Stop button. Click the Close button to close the bus monitor. 6. Open the log file that you specified in the previous steps and view its contents.

End of Exercise C-1

LabVIEW Introduction Course Manual

C-16

ni.com

Appendix C

CAN: Controller Area Network

D. CAN APIs
There are two APIs that you can use with NI-CAN hardware: Channel and Frame. Channel API High level Easy-to-use physical units Easy CAN/DAQ synchronization Not compatible with NI-CAN 1.6 or lower Lower-level, advanced API Command/response protocol Advanced CAN/DAQ synchronization Compatible with all versions of NI-CAN

Frame API

For a single NI-CAN port such as CAN0, you can use only one API at a time. For example, if you have one application that uses the Channel API and another application that uses the Frame API, you cannot use CAN0 with both at the same time. If you have a 2-port CAN card, you can connect CAN0 and CAN1 to the same CAN network, then use CAN0 with one application and CAN1 with the other. Alternately, you can use CAN0 for both applications, but run each application at a different time. In most cases, you should use the Channel API, because it simplifies programming and reduces development time. However, there are some situations in which the Frame API is necessary; for example: You are maintaining an application developed with NI-CAN version 1.6 or earlier. The Frame API is compatible with code developed in early CAN versions. You need to implement a command/response protocol in which you send a command to the device, and then the device replies by sending a response. Command/response protocols typically use a fixed pair of IDs for each device, and the ID does not determine the meaning of the data bytes. Your devices require use of remote frames. The Channel API does not provide support for remote frames, but the Frame API has extensive features to transmit and receive remote frames. You have advanced requirements for synchronizing CAN and DAQ cards. The Frame API provides RTSI features that are lower level than the synchronization features of the Channel API.

Note

This course covers only the Channel API.

National Instruments Corporation

C-17

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

E. CAN Programming in LabVIEW (Channel API)

The basic NI-CAN program consists of an initialization and start, a read or write data, and a clear. A Get Names VI is also frequently used to access the list of channels names in a database. The link between the functions is the task reference. A CAN task is a collection of CAN channels that have identical timing and the same communication directionread or write. A task can encompass several messages, but they must all be on the same interface or port.

CAN Init Start VI

The CAN Init Start VI initializes a task for the specified channel list and starts communication. The mode input determines whether the task is configured to read or write.

Figure C-11. CAN Init Start VI

CAN Get Names VI

The VI gets an array of CAN channel names or message names from MAX or a CAN database file. If you leave the file path input unwired, the channel names are retrieved from MAX. Otherwise, they are retrieved from the database file you specify. The mode input determines whether you are accessing channel names or message names.

Figure C-12. CAN Get Names VI

There are three ways to access channels in your application. specify a channel name that has been imported into MAX specify a database file and channel name for channels not in MAX use the CAN Get Names VI to access all channels in a database file

LabVIEW Introduction Course Manual

C-18

ni.com

Appendix C

CAN: Controller Area Network

To directly access a CAN channel from a CAN database, specify the channel name with the database path as a prefix. For example, if you use a channel named Switch0 in the C:\CAN Demo Box.DBC CAN Database, pass C:\CAN Demo Box.DBC::Switch0 to the Init Start function, as shown in Figure C-13. This figure also demonstrates how to read a channel available in MAX, and how to extract all channels from a database file.

Figure C-13. Specifying Channels in LabVIEW

CAN Read
The CAN Read VI reads samples from an input CAN task. Samples are obtained from received CAN messages. Right-click the icon and select Select Type from the shortcut menu to choose the output data type.

Figure C-14. CAN Read VI

National Instruments Corporation

C-19

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

CAN Write
The CAN Write VI writes samples to an output CAN task. Samples are placed into transmitted CAN messages. Right-click the icon and select Select Type from the shortcut menu to choose the write data type.

Figure C-15. CAN Write VI

CAN Clear
The CAN Clear VI stops communication for the task and clears the configuration.

Figure C-16. CAN Init Start VI

LabVIEW Introduction Course Manual

C-20

ni.com

Appendix C

CAN: Controller Area Network

Exercise C-2
Goal

Read and Write CAN Channels

Read and write channels from the CAN device using LabVIEW.

Description
Complete a VI that reads a single value at a time from the CAN Interface and graphs it on a chart. The channel being read is Analog Input on Channel 0 of the CAN Demo box.
Note Before beginning this exercise, load the CAN Demo Box.ncd or CAN Demo Box.dbc database into MAX. Also, wire the Function Generator Gen

output to the Analog In To CAN Ch0 input on the CAN demo box. You completed these steps in a previous exercise.

Part A: Read a Single Channel

1. Open Read CAN Channels VI, located in the <Exercises>\ LabVIEW Basics I\CAN directory. In the following steps, you complete the block diagram shown in Figure C-17.

Figure C-17. Read CAN Channels VI Block Diagram

2. Add the CAN Channel VIs to the block diagram. Add the CAN Init Start VI to the block diagram to the left of the While Loop. Right-click the channel list input of the CAN Init Start VI and select CreateControl.

National Instruments Corporation

C-21

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Right-click the interface input of the CAN Init Start VI and select CreateControl. Right-click the mode input of the CAN Init Start VI, select Create Constant. Select Input from the mode enum constant. Add the CAN Read VI to the block diagram inside the While Loop. Right-click the CAN Read VI and select Visible Items Polymorphic VI Selector. Selecting the menu item toggles the display of the polymorphic VI selector. A check mark indicates whether it is selected.
Note

Select Single-Chan Single-Samp Dbl from the pull-down menu on the CAN Read VI.
Tip You also can accomplish this by right-clicking the VI and selecting Select Type Single-Chan Single-Samp Dbl from the shortcut menu.

Add the CAN Clear VI to the block diagram to the right of the While Loop. 3. Wire the block diagram as shown in Figure C-17. 4. Switch to the front panel. 5. Test the VI. Set the interface control to CAN0. Enter AnalogInToCANCh0 into the first array element of the channel list control.
Tip You also can drag the name of the channel into the array element from MAX. The channel is found in the message WAVEFORM0_SAW0_FROM_CDB (0x710).

Run the VI. Experiment with CAN Demo Box. Change the signal time and frequency. Notice the changes taking effect on your chart.

LabVIEW Introduction Course Manual

C-22

ni.com

Appendix C

CAN: Controller Area Network

Your front panel should resemble the following figure.

Figure C-18. Read CAN Channels VI Front Panel

Click the Stop button to terminate the program. 6. Save the VI as Read CAN Channels.vi in the <Exercises>\ LabVIEW Basics I\CAN directory.

Part B: Read Two Channels

Modify the VI to read a second channel, Switch0. 1. Add a second channel to the front panel of the Read CAN Channels VI.

Figure C-19. Read CAN Channels (Multiple) VI Front Panel

Expand the number of array elements visible on the channel list control on the front panel of the Read CAN Channels VI. Enter Switch0 into the second array element of the channel list control. Add numeric indicator to the front panel.

National Instruments Corporation

C-23

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

2. Modify the block diagram as shown in Figure C-20 to display the second channel.

Figure C-20. Read CAN Channels (Multiple) VI Block Diagram

Switch to the block diagram. Delete the wire between the output of the CAN Read VI and the waveform chart. Select Multi-Chan Single-Samp 1D Dbl from the pull-down menu that appears below the CAN Read VI (the polymorphic VI selector). This specifies that the VI should read an array of doubles, one from each channel, every time that it executes. Add an Index Array function to the block diagram. Using the cursor, drag the border of the Index Array function to expand its size so that it returns two array elements instead of one. Wire the multi-chan single-samp 1D dbl output array from the CAN Read VI to the array input of the Index Array function. Right-click the index0 input of the Index Array function and select CreateConstant. Right-click the index1 input of the Index Array function and select CreateConstant.

LabVIEW Introduction Course Manual

C-24

ni.com

Appendix C

CAN: Controller Area Network

Enter 1 in the second constant. Connect the first output element of the Index Array function to the waveform chart indicator terminal and connect the second output element to the Switch0 indicator terminal. 3. Save the VI as Read CAN Channels (Multiple).vi in the <Exercises>\LabVIEW Basics I\CAN directory. 4. Switch to the front panel. 5. Test the VI. Run the VI. While it is running, experiment with changing the properties of the function generated by the CAN Demo Box. Experiment with changing the state of Switch0 as well. As you toggle the switch (Digital Input 0) on the CAN Demo Box, notice that the value of the numeric indicator changes. 6. Use another VI to modify the frequency of the waveform generated by the demo box. Open the Write CAN Channels VI, located in the <Exercises>\ LabVIEW Basics I\CAN directory. Ensure that the channel list has one element with the channel name FunctionGeneratorFrequency. Set the interface control to CAN0. Run the CAN Read Channels VI and the CAN Write Channels VI. Experiment with changing the Frequency Value control on the CAN Write Channels VI and see how it affects the chart for the CAN Read Channels VI. 7. Terminate the execution of both VIs by clicking their Stop buttons.

End of Exercise C-2

National Instruments Corporation

C-25

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Exercise C-3
Goal

Synchronize CAN & DAQ

Synchronize CAN and DAQ inputs in LabVIEW.

Description
There are two CAN and DAQ acquisitions inputting data simultaneously. Both the acquisitions are buffered, meaning that the timing is handled on the interface devices. Explore a VI that synchronizes the inputs by routing the clock signal from one of the devices to the other using a Real-Time Serial Interface (RTSI) cable to connect the two. 1. Open the Sync CAN & DAQ VI located in the <Exercises>\ LabVIEW Basics I\CAN directory. 2. Switch to the block diagram. 3. Explore the block diagram shown in Figure C-21. Notice that this VI reads from both the CAN and DAQ interfaces and uses RTSI to synchronize the timing.

Figure C-21. Sync CAN & DAQ VI Block Diagram

4. Switch to the front panel. 5. Set the control values: Interface: CAN0 Channel List: AnalogInToCANCh0

LabVIEW Introduction Course Manual

C-26

ni.com

Appendix C

CAN: Controller Area Network

Physical channels: Dev1/ai0 RTSI Terminal: RTSI0 Sample Rate: 1000.00 6. On the CAN Demo Box, attach two wires to jumper between the output of the Functions Generator, the input Analog In to CAN Ch0, and the input Analog In to DAQ Ch0. 7. Run the VI. Notice that the signals read from the CAN interface and the DAQ device are perfectly synchronized. To terminate the VI, click the Stop button. 8. Close the VI when you are finished.

End of Exercise C-3

National Instruments Corporation

C-27

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Self Review: Quiz

1. Which of the following is the maximum transmission rate of Low Speed or Fault-tolerant CAN? a. 1 Mbaud/s b. 83.3 kbaud/s c. 256 kbaud/s d. 125 kbaud/s 2. Which of the following is a reason to use NI-CAN channels? a. They allow associating bits/bytes of a CAN message/frame with meaningful names and scaling information. b. They allow access to the CAN message/frame in its entirety. c. They allow access to the CAN physical bus channel. d. They allow associating different types of CAN frames with user defined names. 3. Which of the following is a reason to use the NI-CAN Frame API? (multiple answers) a. It allows complete control of CAN frame communication on the bus. b. It simplifies programming and reduces development time. c. It allows advanced synchronization with National Instruments DAQ devices. d. It allows you to use both the Frame API and the Channel API on the same CAN device/node.

National Instruments Corporation

C-29

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Self Review: Quiz Answers

1. Which of the following is the maximum transmission rate of Low Speed or Fault-tolerant CAN? a. 1 Mbaud/s b. 83.3 kbaud/s c. 256 kbaud/s d. 125 kbaud/s 2. Which of the following is a reason to use NI-CAN channels? a. They allow associating bits/bytes of a CAN message/frame with meaningful names and scaling information. b. They allow access to the CAN message/frame in its entirety. c. They allow access to the CAN physical bus channel. d. They allow associating different types of CAN frames with user defined names. 3. Which of the following is a reason to use the NI-CAN Frame API? (multiple answers) a. It allows complete control of CAN frame communication on the bus. b. It simplifies programming and reduces development time. c. It allows advanced synchronization with National Instruments DAQ devices. d. It allows you to use both the Frame API and the Channel API on the same CAN device/node.

National Instruments Corporation

C-31

LabVIEW Introduction Course Manual

Appendix C

CAN: Controller Area Network

Notes

LabVIEW Introduction Course Manual

C-32

ni.com

Additional Information and Resources

This appendix contains additional information about National Instruments technical support options and LabVIEW resources.

National Instruments Technical Support Options

Visit the following sections of the National Instruments Web site at ni.com for technical support and professional services. SupportOnline technical support resources at ni.com/support include the following: Self-Help ResourcesFor answers and solutions, visit the award-winning National Instruments Web site for software drivers and updates, a searchable KnowledgeBase, product manuals, step-by-step troubleshooting wizards, thousands of example programs, tutorials, application notes, instrument drivers, and so on. Free Technical SupportAll registered users receive free Basic Service, which includes access to hundreds of Application Engineers worldwide in the NI Discussion Forums at ni.com/forums. National Instruments Application Engineers make sure every question receives an answer. For information about other technical support options in your area, visit ni.com/services or contact your local office at ni.com/contact. System IntegrationIf you have time constraints, limited in-house technical resources, or other project challenges, National Instruments Alliance Partner members can help. The NI Alliance Partners joins system integrators, consultants, and hardware vendors to provide comprehensive service and expertise to customers. The program ensures qualified, specialized assistance for application and system development. To learn more, call your local NI office or visit ni.com/alliance.

If you searched ni.com and could not find the answers you need, contact your local office or NI corporate headquarters. Phone numbers for our worldwide offices are listed at the front of this manual. You also can visit the Worldwide Offices section of ni.com/niglobal to access the branch office Web sites, which provide up-to-date contact information, support phone numbers, email addresses, and current events.

National Instruments Corporation

D-1

LabVIEW Introduction Course Manual

Appendix D

Additional Information and Resources

Other National Instruments Training Courses

National Instruments offers several training courses for LabVIEW users. These courses continue the training you received here and expand it to other areas. Visit ni.com/training to purchase course materials or sign up for instructor-led, hands-on courses at locations around the world.

National Instruments Certification

Earning an NI certification acknowledges your expertise in working with NI products and technologies. The measurement and automation industry, your employer, clients, and peers recognize your NI certification credential as a symbol of the skills and knowledge you have gained through experience. Visit ni.com/training for more information about the NI certification program.

LabVIEW Resources
This section describes how you can receive more information regarding LabVIEW.

LabVIEW Publications
The following publications offer more information about LabVIEW.

LabVIEW Books
Many books have been written about LabVIEW programming and applications. The National Instruments Web site contains a list of all the LabVIEW books and links to places to purchase these books.

info-labview Listserve
info-labview is an email group of users from around the world who discuss LabVIEW issues. The list members can answer questions about building LabVIEW systems for particular applications, where to get instrument drivers or help with a device, and problems that appear.

To subscribe to info-labview, send email to:

[email protected]

To subscribe to the digest version of info-labview, send email to:

[email protected]

To unsubscribe to info-labview, send email to:

[email protected]

LabVIEW Introduction Course Manual

D-2

ni.com

Appendix D

Additional Information and Resources

To post a message to subscribers, send email to:

[email protected]

To send other administrative messages to the info-labview list manager, send email to:
[email protected]

You might also want to search previous email messages at:

www.searchVIEW.net

The info-labview web page is available at:

www.info-labview.org

National Instruments Corporation

D-3

LabVIEW Introduction Course Manual

Index
A
ADC, 8-17 adding files to projects, 2-11 algorithms, designing, 1-3 aliasing (figure), B-17 alignment and spacing, 4-4 analog input task timing, 8-17 task triggering, 8-18 analog output, 8-24 DAC, 8-25 task timing, 8-24 task triggering, 8-25 analog-to-digital conversion, 8-17 analysis categories, A-4 inline versus offline, A-2 programmatic versus interactive, A-3 applications, developing modular, 7-1 arrays, 5-2 2D, 5-3 auto-indexing, 5-4 creating 2D arrays using auto-indexing, 5-6 creating constants, 5-4 creating controls and indicators, 5-3 dimensions, 5-2 examples of 1D arrays, 5-2 examples of 2D arrays, 5-3 initializing, 5-4 outputs, 5-5 restrictions, 5-2 auto-indexing creating 2D arrays, 5-6 using to set For Loop count, 5-5 automatic wiring, 2-25

B
block diagram, 2-20 automatic wiring, 2-25 controls, indicators, and constants (figure), 2-22 creating cluster constants, 5-15 data flow, 2-44 documenting code (figure), 4-17 figure, 2-20 nodes, 2-23 toolbar, 2-27 window, 2-3 wiring automatically, 2-25 wiring to charts, 4-53 Boolean controls and indicators, 2-15 values, 4-12 Booleans mechanical actions (figure), 4-6, 4-12 Breakpoint tool conditional breakpoints with probes, 3-15 debugging VIs, 3-16 breakpoints, 3-16 broken VIs causes, 3-9 common causes, 3-10 correcting, 2-50, 3-9 displaying errors, 3-9 Bundle By Name function, 5-17 Bundle function, 5-17

C
callers chain of, 3-17 displaying, 3-17 captions and labels, 4-2

National Instruments Corporation

I-1

LabVIEW Introduction Course Manual

Index

Case structures, 4-63 Boolean cases, 4-66 changing case views (figure), 4-64 enum cases, 4-67 error cases, 4-68 executing, 4-63 integer cases, 4-66 selecting cases, 4-64 selector terminals, 4-63 specifying a default case, 4-63 string cases, 4-67 certification (NI resources), D-2 chain of callers displaying, 3-17 chart update mode (figure), 4-53 charts update mode, 4-52 figure, 4-53 waveform, 4-52 figure, 4-52 wiring, 4-53 clusters, 5-14 assembling from individual elements, 5-17 constants, 5-14 creating, 5-14 creating constants, 5-15 disassembling, 5-18 error, 3-19, 5-19 order, 5-15 order of elements, 5-15 reordering, 5-15 figure, 5-16 replacing or accessing elements, 5-17 using functions, 5-16 wire patterns, 5-14 code, documenting, 4-16 coercion For Loops (figure), 4-40 numeric data, 4-38, 4-39 colors, 4-4

communicating with instruments, 9-38 serial, 9-3, C-9 VISA, 9-31 conditional breakpoints. See probes conditional terminals, 4-26 configuration software (Windows), 9-7 connector panel, 2-3 connector panes, 7-4 assigning terminals to controls and indicators, 7-8 configuring, 7-6 modifying layout, 7-7 setting inputs and outputs, 7-9 constants arrays, 5-4 clusters, 5-14, 5-15 Context Help window, 3-2 figure, 3-2 terminal appearance, 3-2, 7-9 control flow programming model, 2-44 control panels, limits, 7-10 controls, 2-14 assigning to connector pane, 7-8 custom, 5-26 numeric, 2-15 numeric (figure), 2-15 string display types, 4-13 type definitions, 5-28 controls and indicators Boolean, 2-15 creating arrays, 5-3 creating clusters, 5-14 defaults (figure), 4-3 designing, 4-2 figure, 4-3 limits, front panel, 7-10 naming, 4-17 numeric, 2-15 options, 4-3 showing terminals, 2-26 string, 2-16 figure, 2-16

LabVIEW Introduction Course Manual

I-2

ni.com

Index

controls palette, 2-16 figure, 2-16 controls, indicators, and constants, 2-21 conventions used in the manual, x conversion, numeric, 4-38, 4-39 correcting broken VIs, 2-50, 3-9 count terminals, 4-37 counters, 8-26 course conventions used in the manual, x goals, x requirements for getting started, ix software installation, ix creating clusters, 5-14 creating VIs, 2-47 acquire, 2-48 analyze, 2-48 present, 2-49 custom controls, 5-26 linking to a saved file, 5-28

D
DAC, 8-25 analog input, 8-17 DAQ analog output, 8-24 analog-to-digital conversion, 8-17 configuring hardware, 8-7 counters, 8-26 DAC, 8-25 devices, 8-4 digital I/O, 8-30 NI-DAQ, 8-5 scales, 8-9 Signal Accessory, 8-3 simulated devices creating, 8-10 removing, 8-10 simulating devices, 8-10 software architecture, 8-5 task timing, 8-24 task triggering, 8-25

terminal blocks & cables, 8-2 typical system (figure), 8-2 data acquiring, 8-1 disk streaming, 6-8 file formats, 6-2 measurement data, 6-1 numeric, A-1 plotting, 4-52 reading and writing, 6-2 figure, 6-2 relating, 5-1 undefined, 3-17 unexpected, 3-17 data coercion numeric, 4-38, 4-39 figure, 4-39 data flow. See dataflow data transfer rate, 9-3 serial, 9-5 data transfer termination, 9-3 data transfer, iterative, 4-45 data types, 2-25, 4-9 Boolean values, 4-12 default values, 4-65 dynamic, 4-15 enums, 4-14 numeric, 4-9 figure, 4-10 floating-point, 4-10 strings, 4-12 terminals, 4-9 database access, 2-24 dataflow, 2-44 figure, 2-45 observing, 3-12 dataflow programming model, 2-44 debugging automatic error handling, 3-18 breakpoints, 3-16 broken VIs, 2-50, 3-9 error handling, 3-18 execution, highlighting (figure), 3-13

National Instruments Corporation

I-3

LabVIEW Introduction Course Manual

Index

Probe tools, 3-13 probes, 3-14 single-stepping, 3-13 suspending execution, 3-16 techniques, 3-11 execution highlighting, 3-12 using execution highlighting, 3-12 using probes, 3-13 using the Breakpoint tool, 3-16 debugging and troubleshooting VIs, 3-1 decorations, 4-7 default cases, 4-63 design, 1-3 additional requirements, 1-3 algorithms, 1-3 flowchart, 1-4 inputs, 1-3 outputs, 1-3 state transition diagram, 1-5 techniques and patterns, 10-1 designing controls and indicators, 4-2 designing front panel windows, 4-2 device range ADC precision, B-13 description, B-13 devices, simulating, 8-10 diagnostic tools (NI resources), D-1 dialog box new (figure), 2-6 properties (figure), 2-18 property, 2-17 digital I/O, 8-30 digital-to-analog conversion, 8-25 dimensions, arrays, 5-2 directory paths. See probes disk streaming, 6-8 figure, 6-9 displaying chain of callers, 3-17 errors, 3-9 documentation LabVIEW Help, 3-3 NI resources, D-1

documenting code, 4-16 block diagrams (figure), 4-17 controls and indicators, 4-17 descriptions, 4-16 graphical programming, 4-17 tip strips, 4-16 VI properties, 4-16 drivers (NI resources), D-1 dynamic data types, 4-15

E
editing icons, 7-4 elapsed time, 4-44 Embedded Project Manager, 2-9 enums, 4-14 enums (figure), 4-14 error handling, 3-18, 3-19 using Case structures, 4-68 with While Loops, 4-29 error list (figure), 3-10 errors automatically handling, 3-18 broken VIs, 2-50, 3-9 checking & handling, 3-18 clusters, 3-19 codes, 3-19 displaying, 3-9 explaining, 3-20 finding, 3-9 handling, 3-18 automatically, 3-18 using For Loops, 4-29 using While Loops, 4-29 list, 3-9 methods to handle, 3-19 Run button, 2-50 window, 3-9 Example Finder. See NI Example Finder examples (NI resources), D-1

LabVIEW Introduction Course Manual

I-4

ni.com

Index

execution debugging VIs, 3-12 flow, 2-44 highlighting, 3-12 figure, 3-13 suspending, 3-16 to debug VIs, 3-16 explain error, 3-20

F
favorites, adding, 2-31 file I/O, 6-2 basic operation, 6-2 disk streaming, 6-8 figure, 6-2 overview, 6-4 refnums, 6-2 files formats, 6-2 LabVIEW Data Directory, 6-3 finding errors, 3-9 fixing VIs, 2-50, 3-9 flow of execution, 2-44 flowcharts, designing, 1-4 fonts and text, 4-6 For Loops, 4-37 auto-indexing arrays, 5-4 coercion (figure), 4-40 count terminals, 4-37 error handling, 4-29 figure, 4-37 iteration terminals, 4-37 setting count using auto-indexing, 5-5 stacked shift registers, 4-47 Formula Nodes, 4-74 entering C-like statements, 4-74 entering equations, 4-74 front pane window array controls and indicators, 5-3 front panel (figure), 2-20

front panel window, 2-2, 2-14 creating cluster controls and indicators, 5-14 figure, 2-14 toolbar, 2-18 front panel windows designing, 4-2 object, resizing, 4-8 front panels, controls, indicators, and constants (figure), 2-21 functions, 2-23 functions palette, 2-26 favorites, 2-31 figure, 2-27 furnace example, 1-4 figure, 1-4, 1-6

G
GPIB, 9-2 communicating with instruments, 9-38 configuration software (Windows), 9-7 data transfer rate, 9-3 data transfer termination, 9-3 interface (figure), 9-8 software architecture, 9-7, C-17 graphical programming, 4-17 graphs configuring, 4-54 multiple-plot waveform, 4-55 single-plot waveform, 4-55 waveform (figure), 4-54 XY, 7-2 grouping data in arrays, 5-2 data in clusters, 5-14 data in strings, 4-12

National Instruments Corporation

I-5

LabVIEW Introduction Course Manual

Index

H
hardware, 8-2 configuring, 8-5, 8-7 DAQ devices, 8-4 drivers, 8-5 interfaces, other, 9-6 MAX, 8-8 NI-DAQ, 8-5 terminal blocks & cables, 8-2 Windows, 8-8 help online, 3-3 technical support, D-1 hiding labels, 4-3 highlighting execution debugging VIs, 3-12

I
I/O communicating with instruments, 9-38 GPIB software architecture, 9-7, C-17 serial, 9-3, C-9 serial hardware overview, 9-6 VISA, 9-31 icon and connector panes, 7-3 icons, 2-3, 7-3 creating, 7-4 editing (figure), 7-5 implementation, 1-6 implementing VIs, 4-1 incrementally running VIs, 3-13 indicators, 2-14 assigning to connector pane, 7-8 numeric, 2-15 figure, 2-15 string display types, 4-13 type definitions, 5-28 indicators and controls Boolean, 2-15 creating arrays, 5-3 creating clusters, 5-14 defaults (figure), 4-3

designing, 4-2 naming, 4-17 numeric, 2-15 options, 4-3 showing terminals, 2-26 string, 2-16 figure, 2-16 initializing arrays, 5-4 shift registers, 4-46 inputs identifying, 1-3 setting, 7-9 inputs and outputs optional, 7-9 settings required, 7-9 installing the course software, ix instances of subVIs determining, 3-17 suspending execution, 3-16 instrument control, 9-1, 9-2 GPIB, 9-2 Instrument I/O Assistant, 9-14 interfaces, other, 9-6 instrument drivers categories, 9-40 definition, 9-38 example (figure), 9-19, 9-39 locating, 9-38 NI resources, D-1 understanding, 9-39 Instrument I/O Assistant, 9-14 instruments, types, 9-2 interfaces, 9-6 iteration terminals For Loops, 4-37 While Loops, 4-27 iterative data transfer, 4-45

LabVIEW Introduction Course Manual

I-6

ni.com

Index

K
KnowledgeBase, D-1

L
Labeling tool, 2-37 figure, 2-37 labels and captions, 4-2 hiding labels (figure), 4-3 LabVIEW data directory, 6-3 Getting Started Window (figure), 2-4 Help, 3-2, 3-3 navigating, 2-1 to 2-65 loops For Loops, 4-37 figure, 4-37 While Loops, 4-26

modularity, 7-2 figure, 7-3 multiple-plot waveform graphs, 4-55 multiplot XY graphs, 4-57

N
National Instruments support and services, D-1 navigating LabVIEW, 2-1 to 2-65 new projects, creating, 2-5 new VIs, creating, 2-5 NI Certification, D-2 NI Example Finder, 3-4 figure, 3-4 NI-DAQ simulated devices, creating, 8-10 simulated devices, removing, 8-10 nodes, 2-23 database access, 2-24 display modes (figure), 2-24 versus icons, 2-23 noise, decreasing, B-17 numeric controls and indicators, 2-15 numeric conversion, 4-38, 4-39 numerics, 4-9 complex numbers, 4-11 floating-point numbers, 4-10 integers, 4-11

M
maintenance, 1-7 MAX (Measurement & Automation Explorer), 8-8 measurement data, storing, 6-1 measurements concepts, B-3 fundamentals, B-1 increasing quality, B-12 noise, B-17 overview (figure), B-1, B-3 sampling rates (figure), B-17 scales, 8-9 shape recovery, B-16 signal conditioning, B-5 signal sources, B-4 smallest detectable change, B-12 systems, B-8 computer-based, B-2 menus, 4-7 figure, 4-5 shortcut, 2-17 modular applications, developing, 7-1

O
objects, wiring automatically on block diagram, 2-25 online help, 3-3 opening VIs, 2-6 Operating tool, 2-34 figure, 2-34 order in clusters, 5-15 of cluster elements, 5-15 of execution, 2-44 organizing project items, 2-12

National Instruments Corporation

I-7

LabVIEW Introduction Course Manual

Index

outputs identifying, 1-3 setting, 7-9

P
palettes controls, 2-16 figure, 2-16 Tools, 2-33 figure, 2-33 parallelism, 10-21 Parts of a VI. See VIs, parts phenomena, B-4 plotting data, 4-52 Positioning tool, 2-35 figure, 2-35 resizing (figure), 2-36 probes debugging VIs, 3-14 default, 3-15 generic, 3-14 indicators, 3-14 supplied, 3-15 types of, 3-14 problem solving, 1-1 programming parallelism, 10-21 sequential, 10-2 figure, 10-3 state machines, 10-5 programming examples (NI resources), D-1 project, 1-10 figure, 1-11 Project Explorer, 2-9 toolbars, project-related, 2-10 window, 2-9 figure, 2-10 project, state transition diagram figure, 1-11, 1-12

projects adding files, 2-11 creating, 2-10 new, 2-5 organizing, 2-12 removing files, 2-12 saving, 2-13 viewing files, 2-13 property dialog boxes, 2-17 figure, 2-18

R
Read from Measurement File VI, 6-4 Read From Spreadsheet File VI, 6-4 refnums, file I/O, 6-2 relating data, 5-1 removing project files, 2-12 requirements for getting started, ix resizing front panel objects, 4-8 Run button errors, 2-50

S
sampling rates (figure), B-17 saving projects, 2-13 VIs, 2-7 VIs as (figure), 2-8 scales, 8-9 scenario, 1-2 scope chart, 4-52 SCXI signal conditioning amplification, B-6 linearization, B-7 phenomena and transducers (table), B-4 transducer excitation, B-7 searching for controls, VIs, and functions, 2-30 figure, 2-30

LabVIEW Introduction Course Manual

I-8

ni.com

Index

selector terminals, 4-63 sequential programming (figure), 10-3 serial port communication, 9-3, C-9 character frame, 9-5 data transfer rate, 9-5 figure, 9-4 hardware overview, 9-6 shift registers initializing, 4-46 stacked, 4-47 shortcut menus, 2-17 figure, 2-17 signal conditioning, B-5 See also SCXI amplification, B-6 figure, B-6 linearization, B-7 phenomena and transducers (table), B-4 transducer excitation, B-7 signal sources, B-4 simulating devices, 8-10 single-plot waveform graphs, 4-55 single-plot XY graphs, 4-57 single-stepping debugging VIs, 3-13 smart probes. See probes software (NI resources), D-1 software development method, 1-2, 1-8 spacing and alignment, 4-4 starting a VI, 2-4 state machine design pattern Case structure, 10-8 controlling default transition, 10-7 multiple state transitions, 10-8 two-state transition, 10-8 State Diagram Toolkit, 10-9 transition array, 10-9

state machines, 10-5 applying, 10-5 controlling, 10-7 infrastructure, 10-6 infrastructure (figure), 10-6 transitioning, 10-7 state transition diagram, designing, 1-5 stepping through VIs debugging VIs, 3-13 stopping While Loops (figure), 4-29 strict type definitions, 5-29 string controls and indicators, 2-16 figure, 2-16 strings, 4-12 display types, 4-13 strip chart, 4-52 structure tunnels, 4-28 structures Case, 4-63 stacked shift registers, 4-47 tunnels, 4-65 subVIs, 2-23, 7-9 assigning controls and indicators to connector pane, 7-8 configuring the connector pane, 7-6 creating, 7-10 creating (figure), 7-10 creating icons, 7-4 determining current instance, 3-17 displaying chain of callers, 3-17 editing icons (figure), 7-5 icons, 7-3 modifying connector panes, 7-7 opening and editing, 7-9 setting inputs and outputs, 7-9 suspending execution, 3-16 supplied probes, 3-15 support, technical, D-1 suspending execution, 3-16 sweep chart, 4-52

National Instruments Corporation

I-9

LabVIEW Introduction Course Manual

Index

T
tab controls, 4-7 targets, 2-9 task timing, 8-17 analog output, 8-24 task triggering, 8-18 analog output, 8-25 technical support, D-1 templates, creating a VI, 2-5 terminals, 2-20 conditional, 4-26 Context Help window appearance, 3-2, 7-9 controls, indicators, and constants, 2-21 figure, 2-21, 2-22 count, 4-37 data types, 4-9 iteration on For Loops, 4-37 iteration on While Loops, 4-27 optional, 7-9 recommended, 7-9 required, 7-9 selector, 4-63 showing on block diagram, 2-26 testing, 1-7 text and fonts, 4-6 timing VIs, wait functions, 4-44 timing, elapsed time, 4-44 tips, user interface, 4-6 toolbars block diagram, 2-27 front panel window, 2-18 project-related, 2-10 tools Labeling, 2-37 figure, 2-37 Operating, 2-34 figure, 2-34 Positioning figure, 2-35 positioning, 2-35 figure, 2-36

wiring, 2-38 figure, 2-38 Tools palette, 2-33, 2-39 figure, 2-33 training (NI resources), D-2 transducers, B-4 excitation, B-7 figure, B-6 linearization, B-7 phenomena and transducers (table), B-4 troubleshooting, 3-9 and debugging VIs, 3-1 NI resources, D-1 tunnels, 4-65 While Loop figure, 4-28 type definitions, 5-26, 5-28 defining, 5-28 strict, 5-29

U
Unbundle By Name function, 5-17 Unbundle function, 5-17 undefined data, preventing, 3-18 unexpected data, 3-17 user interface decorations, 4-7 menus, 4-7 system controls, system controls, 4-6 tab controls, 4-7 tips and tools, 4-6 user probes. See probes using color, 4-4 Utilities, NI Example Finder, 3-4

V
viewing files in projects, 2-13 virtual instruments, 2-2 VIs, 2-2 acquire, 2-48 analyze, 2-48 broken, 2-50, 3-9

LabVIEW Introduction Course Manual

I-10

ni.com

Index

broken, causes, 3-9, 3-10 configuring the connector pane, 7-6 correcting, 2-50, 3-9 creating, 2-47 creating for a template, 2-5 creating subVIs, 7-10 figure, 7-10 error handling, 3-18 front panel window, 2-2 icons, 2-23, 7-2 implementing, 4-1 loading status (figure), 2-7 modularity, 7-2 figure, 7-3 new, 2-5 nodes, 2-23 opening, 2-6 parts block diagram, 2-3 icon and connector panel, 2-3 present, 2-49 running, 2-50 saving, 2-7 saving as (figure), 2-8 starting, 2-4 subVIs, 7-9 timing, 4-44 troubleshooting and debugging, 3-1 VISA, 9-31, 9-33 terminology, 9-31 with serial (figure), 9-14, 9-33

Web resources, D-1 While Loops, 4-26 auto-indexing arrays, 5-4 conditional terminals, 4-26 error handling, 4-29 figure, 4-26 iteration terminals, 4-27 stacked shift registers, 4-47 stopping, 4-29 stopping (figure), 4-29 tunnels, 4-28 windows, Project Explorer, 2-9 figure, 2-10 wires, 2-25 automatic, 2-25 common types, 2-25 data types, 2-25 wiring automatically, 2-25 charts, 4-53 tunnels, 4-65 Wiring tool, 2-38 figure, 2-38 with serial, 9-33 Write to Measurement File VI, 6-4 Write to Spreadsheet File VI, 6-4

X
XY graphs configuring, 4-54 multiplot, 4-57 single-plot, 4-57

W
wait functions, 4-44 waveform charts, 4-52 figure, 4-52 wiring, 4-53 waveform graphs figure, 4-54 multiple-plot, 4-55 single-plot, 4-55

National Instruments Corporation

I-11

LabVIEW Introduction Course Manual

Course Evaluation
Course _______________________________________________________________________________________ Location _____________________________________________________________________________________ Instructor _________________________________________ Date ____________________________________

Student Information (optional)

Name ________________________________________________________________________________________ Company _________________________________________ Phone ___________________________________

Instructor
Please evaluate the instructor by checking the appropriate circle. Instructors ability to communicate course concepts Instructors knowledge of the subject matter Instructors presentation skills Instructors sensitivity to class needs Instructors preparation for the class
Unsatisfactory Poor Satisfactory Good Excellent

Course
Training facility quality Training equipment quality Was the hardware set up correctly? The course length was Yes No Too much Just right Not enough Yes No Sometimes Yes No Too long Just right Too short

The detail of topics covered in the course was The course material was clear and easy to follow. Did the course cover material as advertised?

I had the skills or knowledge I needed to attend this course. Yes No If no, how could you have been better prepared for the course? ____________________________________________________________________ _____________________________________________________________________________________________ What were the strong points of the course? __________________________________________________________ _____________________________________________________________________________________________ What topics would you add to the course? ___________________________________________________________ _____________________________________________________________________________________________ What part(s) of the course need to be condensed or removed? ____________________________________________ _____________________________________________________________________________________________ What needs to be added to the course to make it better? ________________________________________________ _____________________________________________________________________________________________ How did you benefit from taking this course? ________________________________________________________ _____________________________________________________________________________________________ Are there others at your company who have training needs? Please list. ____________________________________ _____________________________________________________________________________________________ _____________________________________________________________________________________________ Do you have other training needs that we could assist you with? _________________________________________ _____________________________________________________________________________________________ How did you hear about this course? NI Web site NI Sales Representative Mailing Co-worker Other _____________________________________________________________________________________