Scribd
Upload
170 views

Danfoss RFI

The document discusses radio frequency interference (RFI) from frequency converters and standards for limiting interference emissions. It provides: 1) An overview of RFI generated by variable frequency drives and how filters are used to reduce conducted and radiated interference. 2) Details on the EN 61800-3 product standard which classifies drive systems into categories C1-C4 based on their environment and voltage/current levels. 3) A comparison of the new EN 61800-3 categories to the EN 55011 environment standard classes, noting facility operators must follow EN 55011 while manufacturers must conform to EN 61800-3.

Uploaded by

ASM_213
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
170 views

Danfoss RFI

The document discusses radio frequency interference (RFI) from frequency converters and standards for limiting interference emissions. It provides: 1) An overview of RFI generated by variable frequency drives and how filters are used to reduce conducted and radiated interference. 2) Details on the EN 61800-3 product standard which classifies drive systems into categories C1-C4 based on their environment and voltage/current levels. 3) A comparison of the new EN 61800-3 categories to the EN 55011 environment standard classes, noting facility operators must follow EN 55011 while manufacturers must conform to EN 61800-3.

Uploaded by

ASM_213
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Practical aspects of high-frequency interference (RFI)

Radio frequency interference


Frequency converters generate variable rotating eld frequencies at corresponding motor voltages due to variable-width rectangular current pulses. The steep pulse edges contain high-frequency components. Motor cables and frequency converters radiate these components and conduct them into the mains system via the cable. Manufacturers use radio frequency interference (RFI) lters (also called mains lters or EMC lters) to reduce the level of this type of interference on the mains feed. They serve to protect devices against high-frequency conducted interference (noise immunity) and to reduce the amount of high-frequency interference emitted by a device over the mains cable or by radiation from the mains cable. The lters are intended to limit these interference emissions to a specied statutory level, which means that as much as possible they should be tted in the equipment as standard. As with mains chokes, with RFI lters the quality of the lter to be used must be clearly dened. Specic limits for interference levels are dened in the EN 61800-3 product standard and the EN 55011 generic standard. EN 61800-3 product standard (2005-07) for electrical drive systems
Classication by category C1 C2 C3 C4

Environment

Environment 1

Environment 1 or 2 (operator decision)

Environment 2

Environment 2

Voltage/current

< 1000 V

> 1000 V In > 400 A Connection to IT network EMC plan required Values exceed Class A2

EMC expertise Limits according to EN 55011

No requirement Class B

Installation and commissioning by an EMC expert Class A1 (plus warning notice) Class A2 (plus warning notice)

Classication of the new categories C1 to C4 of the EN 61800-3 product standard

Standards and directives dene limits


Two standards must be observed for the comprehensive assessment of radio frequency interference. The rst is the EN 55011 environment standard, which denes the limits according to the basic environment: either industrial (classes A1 and A2) or residential (class B). In addition, the EN-61800-3 product standard for electrical drive systems, which came into eect in June 2007, denes new categories (C1 to C4) for

device application areas. Although they are comparable to the previous classes in terms of limits, they allow a wider range of application within the scope of the product standard.

Note: Facility operators must comply with EN 55011 in case of problems. Converter manufacturers must conform to EN 61800-3.

Comparison of limit values*


Still valid First version Mandatory from 2007

EN 55011
(Environment)

EN 61800-3
(Product standard)

EN 61800-3
(Revised standard)

Class B
(Residential area) Group 1+2

Environment 1
(Environment) Class B1

Environment 1
(Residential area) Category C1

Class A
(Industry)
Group 1 (HF Internal)

Environment 2
(Industry) Class A1
No reference!

!
Category C2

!
Class A2

Environment 2
(Industry) Category C3 Category C4

Group 2 (HF External)

Comparison of the new categories C1 to C4 dened by the EN 61800-3 product standard and classes A and B of the EN 55011 environment standard.

* Radiation

1 Four steps to an optimal system: Step 1

You might also like