PRODUCT CATAL O G

200 8

N O TES

www.trinamic.com for detailed information and datasheets

PRODUCT S E L E C T O R

D I S C L A I MER

TR I N AM IC

PR O D U C T C A T AL O G

2008

L I FE SUPPORT POLICY

TRINAMIC Motion Control GmbH & Co. KG does not authorize or warrant any of its products for use in life support systems, without the specific written consent of TRINAMIC Motion Control GmbH & Co. KG. Life support systems are equipment intended to support or sustain life, and whose failure to perform, when properly used in accordance with instructions provided, can be reasonably expected to result in personal injury or death. The information in this catalogue has been assembled carefully and is believed to be correct. However TRINAMIC can take no responsibility for all data to be correct. Please refer to the corresponding data sheets available on www.trinamic.com or on CD for detailed information. All product and company names herein may be trademarks of their registered owners. 05.11.2008 / V6.0, Printed in Germany. 2008 TRINAMIC Motion Control GmbH & Co. KG

NO RESPONSIBILITY IS TAKEN FOR THE C O RRECTNESS OF THIS INFORMATION

TRADEMARKS

COPYRIGHT

www.trinamic.com for detailed information and datasheets

PRODUCT C A T E G O R Y O V E R V I E W

C O N T EXT

I NT EG RA TE D CI RC UI TS
ICs for motion control

M OD UL ES
modules for motion control

25

I NT ER FA CE S
bus interface converters

72

P ANd ri ve s
mechatronic drives

76

M OT OR S
stepper and BLDC motors

88

www.trinamic.com for detailed information and datasheets

PRODUCT S E L E C T O R

I N T E G R A T E D C I R C U ITS

M o t i o n Control ler
TMC 428 TMC 454 TMC 457

Three axis stepper motor controller with integrated sequencer Stepper motor controller with integrated sequencer and encoder feedback Stepper and piezo motor controller with integrated sequencer, encoder feedback and easyPID feedback control

7 8 9

Inte r fa ce Controller
TMC 401 TMC 423

Step-/direction to SPI converter for TMC23x/24x stepper driver family triple incremental encoder interface and companion IC for the TMC428

10 11

Hi g h Precision Sequ encer for Stepper Mo to rs

TMC 332

Microstep sequencer for 2-phase and 3-phase stepper motors

12

Powe r Driver for Step per M otors

TMC 236 TMC 246 TMC 239 TMC 249

Microstep driver for up to 1.5A Microstep driver for up to 1.5A with stallGuard Microstep driver for external MOSFETs for up to 4A Microstep driver for external MOSFETs for up to 4A with stallGuard

13 14 15 16

G a te d river for BL DC and Step per Mo to rs

TMC 603

Three phase motor driver with BLDC back EMF commutation hallFX and current sensing

17

www.trinamic.com for detailed information and datasheets

PRODUCT S E L E C T O R

I N T E G R A T E D C I R C U ITS

M OS F E Ts
TMC 32NP/NP2 TMC 34NP

Complementary 30V MOSFET half bridge / full bridge Complementary 30V MOSFET half bridge

18 19

Integra ted Motion Control ler and Driver fo r Ste ppe r Mo to rs

TMC 211 TMC 222 TMC 223

Microstep motor controller & driver for up to 0.8A with LIN interface Microstep motor controller & driver for up to 0.8A with IIC interface Microstep motor controller & driver for up to 0.8A with IIC interface and sensorless stall detection

20 21 22

Eva lua t ion Boards

TMC 428A-EVAL TMC 249-HVHR

Evaluation board for TMC428, TMC246A, and TMC249A with stallGuard Evaluation board for TMC249 with high voltage and high resolution can be used as add on for TMC428A-Eval

23 24

TMC 457-EVAL TMC 332-EVAL TMC 603-EVAL

Evaluation board for TMC457 Evaluation board for TMC332 Evaluation board for TMC603 board for TMC211 board for TMC222

9 12 17 20 21 22 11

TMC 211-Evalboard Evaluation TMC 222-Evalboard Evaluation TMC 223-EVAL TMC 32NPx-EVAL

Evaluation board for TMC223 Complementary 30V MOSFET Half Bridge / Full Bridge

www.trinamic.com for detailed information and datasheets

MOTION C O N T R O L L E R

I N T E G R A T E D C I R C U ITS

T MC 428
T h r e e A xi s S t e p p e r M o t o r C o n t r ol l e r w i t h I n te g r a t e d S e q ue n c er

M A IN CH A R AC T ER IS T IC S
INFO

The TMC428 is a revolutionary miniaturized low cost and high performance stepper motor controller for up to three motors. It integrates all real time critical tasks in reliable, dedicated hardware: An integrated motion ramp profile generator as well as an adaptable microstep sequencer with microstep RAM table. Advanced stop- and reference switch handling allows for precise and fast referencing as well as on-the-fly position checking. Automatic motor current control gives high motor dynamics while saving energy. The interrupt output can generate precise position pulses. The TMC428 directly connects to SPI drivers or to step-/direction drivers. A second SPI interface allows communication with a host microcontroller. The host microcontroller just needs to do high-level control tasks, e.g. giving the command: Drive motor 2 to position 1000. The TMC428 then automatically calculates the motion ramp based on velocity and acceleration parameters. The TMC423 adds encoder functionality to the TMC428. Evaluation Boards, application notes, spreadsheets for parameter calculation, C code examples and schematics are available in order to support short design-in times.
ELECTRICAL DATA INTERFACE

unique minaturized stepper motor controller realized as low power 0.35 CMOS device up to three stepper motors up to 64 times microstepping full step frequencies up to 20 kHz alteration of parameters at any time driver status information read back for C power down mode ideally suited motor drivers are TMC236, TMC239, TMC246 and TMC249 SPI C interface easy-to-use protocol for C serial 4-wire driver interface (SPI) step-/direction output 3.3V or 5V operation CMOS / TTL compatible IOs
PACKAGE

miniature SSOP16 package SO24 package available RoHS compliant

REF 1,2,3

TMC428
Interrupt controller
Ramp& Pulsegenerator
MicrostepController (incl. sequencer)
to driver

CLK

SPI

to C

SPI

serial interface

interface

Driver

serial

to driver

SPI

10 m m

3,3..5V DC
RAM

to driver

SPI

ORDER CODE

D E S C R I PT I O N

TMC428-I TMC428-PI24 TMC428A-EVAL

3-axis controller SSOP16-package 3-axis controller SOP24-package Evaluation board for TMC428, TMC246 and TMC249 with stallGuard

www.trinamic.com for detailed information and datasheets

MOTION C O N T R O L L E R

I N T E G R A T E D C I R C U ITS

T MC 454
S t e p p e r M o t o r C o n t r ol l e r w i t h I n te g r a t e d S e q ue n c er a n d E n c od e r I n f .

M A IN CH A R AC T ER IS T IC S
INFO

The TMC454 is a high-end motion controller for all common 2-, 3-, and 5-phase stepper motors. It provides encoder feedback for high reliability or high position resolution drives. A large set of motion control features is included on this IC. The various function blocks are hardwired and ready-to-use. All processes can be serialized using the instruction based interface. A complete linear & S-shaped ramp generation unit is integrated within the TMC454. All dynamic parameters can be adjusted for a given application in a very broad range. The CPU is relieved from all time critical tasks like ramp calculation or microstep generation. Thus CPU and software engineer can focus on higher level motion control jobs. In many applications, the TMC454 reduces the time time-to-market, and it saves costs for software development and hardware engineering. The TMC454 turns stepper motors into easy to use peripherals! The TMC454 is upwards function compatible to its predecessor TMC453.
ELECTRICAL DATA INTERFACE

upwards function and software compatible to TMC453 controls 2-, 3-, and 5-phase stepper motors full step, half step, sine-step relieves CPU from all time critical tasks incremental encoder interface pulse generation from mHz to MHz S-shaped and linear ramp generation PID controller for holding the position synchronization of multiple TMC454 direct SPI interface for TMC246/TMC249 stepper driver IC family high resolution microstep drive using external SPI DACs interrupt controller 3.3V / 1.5V supply parallel interface (3.3V), with additional control output for optional 5V level shifter serial IIC bus interface
PACKAGE

FBGA144 (1 mm fine pitch, 11 mm * 11 mm) RoHS compliant

RAM
8-bit Parallel

TMC454
step/dir

IIC

REF

CLK

PID controller

Rampgenerator

Command FIFO

analog motor control

PWM DAC

1.5V DC
3.3V DC

SPI DAC interface

TMC249 interface

appropriate

Driver

Step/Dir

Encoder

ABN

Encoder Interface

Microstepcontroller (incl. sequencer)

Interrupt controller
10-bit digital

ORDER CODE

D E S C R I PT I O N

TMC454-BC

1-axis motion controller with encoder feedback

www.trinamic.com for detailed information and datasheets

MOTION C O N T R O L L E R F O R S T E P P E R A N D P I E Z O M O T O R S

I N T E G R A T E D C I R C U ITS

T MC 457
S t e p p e r a n d P i e z o M ot o r C o n t r o l le r ( S - s h a p e R a m ps) w i t h E n co d e r I n t e r f ac e , e a s y P I D F e e d b a c k C on t r ol a n d I n t eg r a t e d S e q u en c e r

M A IN CH A R AC T ER IS T IC S
INFO

The TMC457 is a high-end single axis micro stepping motion controller for 2-phase bipolar stepper motors, piezo motors (Piezo LEGS). Via step / direction interface 3-phase stepper motors can also be controlled (requires additional TMC332). It adds to any microcontroller or processor with SPI interface. It is intended for applications, where a precise and fast, jerk-free motion profile is desired. The TMC457 supports linear and S-shaped velocity ramps. Its chopSync feature allows high speed movement avoiding resonances. An encoder can be added for extremely quick and precise positioning using the internal hardware PID regulator easyPID and for increased reliability / fault detection. For maximum flexibility all motion control parameters (target position, target velocity, acceleration, deceleration and bow) can be changed on-the-fly at any time during motion.
+1.5V +3.3V

S-shaped and linear ramps with on-the-fly alteration of all parameters programmable high resolution sequencer with (12bit, 8192 entry) micro step LUT table integrated sequencer incr. encoder interface with flexible up- and down scaling to match drive resolution fast and stable easyPID PID controller 32 bit registers from mHz to MHz reference switch processing virtual stop sw. (programmable soft limits) position pulse output to trigger ext. events synchronization of multiple axis via step/direction input integrated chopSync for high velocities analog high resolution motor driver control via external dual -low cost- 12 bit DAC energy saving by automatic load angle dependent current control

one capacitor per supply pin

100n

+1.5V

GND

100n

+3.3V

RES

RES
I

TMC457
CLK

ELECTRICAL DATA INTERFACE

3.3V IO/ 1.5V core SPI interface to microcontroller step / direction output (with progr. timing) stallGuard interface for TMC246/TMC249 family stepper motor drivers

CLK

ENABLE

Interface Section

Motion profile generation

S-Ramp generator

Sequencer
O

NSCS

STEP_OUT

Host CPU SPI Interface

SCK

SDI

SPI bus interface

Register Block

target

SDO

Trapezoid Ramp generator

Pulse generator

Output Pulse generator

STEP/ DIR

DIR_OUT

XSTEP_OUT

HIRES_OUT

Step/Dir Output

STDBY_OUT

NINT

Interrupt control

control & status

Position Counter

Microstep RAM 8192*12

POSCOMP

Position compare

2 phase stepper & piezo sequencer

PHA PHB

Optional Step/ Dir Input

STEP_IN

DIR_IN

STEP DIR Prescaler

easyPID PID controller

I
O

NCS_DAC SCK_DAC SDO_DAC_A SDO_DAC_B PZO_EN

Classic stepper driver Analog control of Stepper / Piezo via DAC (LTC2622) TMC246 / TMC249 stepper driver

PACKAGE

FBGA144 package 13 x 13 mm RoHS compliant

PID Stop / Reference Switches Optional Incremental Encoder

STOPL
I

TMC24x SPI interface

STOPR

Stop input processing & virtual stop switches

NCS_DRV SCK_DRV SDO_DRV SDI_DRV NANA_SPI

Encoder
quadrature decoder
Encoder Scaler & Counter

ChopSync

ChopClk

ENC_A ENC_B ENC_N

synchronized chopper clock

10 m m

ORDER CODE

D E S C R I PT I O N

TMC457-BC Related product: TMC457-Eval

1-axis motion controller with encoder feedback, FBGA144 package

Evaluation board for TMC457

www.trinamic.com for detailed information and datasheets

INTERFAC E C O N T R O L L E R

I N T E G R A T E D C I R C U ITS

T MC 401
S t e p / Di r e c t i o n t o S P I co n v e r t e r

M A IN CH A R AC T ER IS T IC S
INFO

The TMC401 converts step/direction signals into SPI datagrams that can be used to drive a TMC236, TMC239, TMC246 or TMC249 stepper motor driver chip directly. It provides five different microstep resolutions (from 1/32 to 1/2) as well as two full step resolution modes. The stallGuard bits of a TMC246 or TMC249 motor driver are output on three pins, in order to allow an easy usage of the stallGuard feature. Also the overtemperature pre-warning bit is output on one extra pin (and can be used to shut off the driver when there is an overtemperature pre-warnINTERFACE

step / directon signal to SPI converter allow step-/direction control for TMC236, TMC246, TMC239, TMC249 drivers outputs for stallGuard value and driver OTPW flag resolution control from fullstep up to 1/32 microsteps optional power down control mixed decay selectable step-/direction input up to 245kHz SPI output
ELECTRICAL DATA

ing condition). The TMC401 also provides a feature that reduces the motor current to 25% when there have not been any step pulses for at least one second. This features can be enabled or disabled. Mixed Decay can also be enabled or disabled using a dedicated pin. The evaluation board contains the TMC401 and different driver configurations of the TMC249 wit external MOSFETs.

5V supply 5V CMOS / TTL compatible IOs TQFP32 package RoHS compliant

PACKAGE

+5V DC

Step/Dir

Power Down feature Mixed Decay Step resolution

StallGuard
3
3

TMC401
Sequencer

e.g. TMC246

Driver

Step Motor
10 m m

Valid
Error
Temperatur prewarning

StallGuard and Error Bit Decoder

interface

Driver

serial

to driver

SPI

Disable

ORDER CODE

D E S C R I PT I O N

TMC401-PI TMC32NPx-EVAL

Step / direction to SPI converter in TQFP-32 package Evaluation board for TMC401-PI, TMC249A-LA & TMC32NP-MLP, TMC249A-SA & TMC32NP2-SM8 and TMC249A-LA & TMC34NP-PSO

www.trinamic.com for detailed information and datasheets

10

INTERFAC E C O N T R O L L E R

I N T E G R A T E D C I R C U ITS

T MC 423
T r i p l e In c r e m e n t a l E n c o d e r I n t e r f a c e a nd C o m p a n i on I C f o r t h e T M C428

M A IN CH A R AC T ER IS T IC S
INFO

The TMC423 is a triple incremental encoder input chip, which interfaces to any SPI compatible controller. It integrates 24 bit counters one for each encoder to provide a high position resolution without CPU interaction. The TMC423 is intended as a companion chip for the TMC428 but not limited to this. Both ICs together enable the realization of a motion control system of three axis with encoder feedback. This provides position verification or stabilization by implementation of some additional software. Further, the TMC423 allows dynamic resolution adaptation for direct comparison of encoder counters with motors using different micro step resolution. All encoder counters can be latched synchronously, or whenever
PACKAGE INTERFACE ELECTRICAL DATA

incremental encoder interface for three 2 or 3 channel encoders TMC428 step / direction interface extension TMC428 reference switch interface TMC428 interrupt de-multiplexer control of LED 6 x 4 Matrix control of key 6 x 4 matrix SPI interface to microcontroller 2.5V and 5V supply required 20mA LED driver outputs 5V CMOS / TTL compatible IOs TQFP100 RoHS compliant

a null channel event occurs, providing a position on strobe holding function. The TMC423 also provides a step / direction output with programmable signal shaping for the TMC428 as well as a multiplexer function for the TMC428 reference switches. Additionally, the TMC423 can drive an LED matrix and read out a switch matrix, to support systems with keyboard user interaction.

TMC423
1-3 1-3 3x Encoder Encoder Encoder

6x4 LED 6x4 Key

3x Encoder Interface

SPI to C

Matrix control

Motion Controller
3

stop switches

Ref. Demux
3x step/dir converter

REF switches

e.g. TMCM428

SPI

3x 3x 3x Driver Driver Driver step/dir

step/dir step/dir

ORDER CODE

D E S C R I PT I O N

TMC423

3-axis encoder interface TQFP100 package

www.trinamic.com for detailed information and datasheets

11

HIGH PRE C I S I O N S E Q U E N C E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T MC 332
M i c r o s t ep S e q u e n c e r f o r 2p h a s e a nd 3 - p h a s e M ot o r s w i t h I n te g r a t e d P W M U n i ts a n d C l o se d L o o p C u r re n t R e g u l a t or

M A IN CH A R AC T ER IS T IC S
INFO

The TMC332 is a high precision micro step sequencer with integrated PWM units. Internal micro step counters with programmable step width make the handling of the physical units comfortable. The TMC428 step direction interface of the TMC332 is directly compatible to the driver chain interface of the TMC428 motion controller. The other step direction interface is a classical two wire step direction interface. Parameterizing of the TMC332 takes place over a common SPI micro controller interface. The integrated sine wave look up table can output either 2 sine waves with a phase shift of 90 for 2-phase stepper motors or 3 sine waves with +/- 120 phase shift for 3-phase motors. The gate control block of the TMC332 provides the gate control signals for the power stage half bridges, including programmable break before make timing and over current protection. Incremental encoders (ABN) to evaluate the physical motor position can be connected to the TMC332. The TMC332 also contains a current measurement unit and a current regulator, requiring only a few inexpensive external components. Switching to fullstep and the chopSync feature allow high velocity operation.
INTERFACE ELECTRICAL DATA

high precision micro step sequencer for smooth motion applications 2-phase stepper motor control 3-phase stepper motor control 9 bit PWM units, 8 bit PWM scaler 4 bit PWM sub-modulation for scaling quantization compensation PWM frequency programmable programmable break-before-make timing integrated current measurement ADC (just 2 LM339, 1 LM324 and some RC required) integrated current regulation manual or automatic microstep to fullstep switching for higher speeds chopSync for high velocity operation operation with 3.3V compatible IOs / 1.5V core voltage 16 MHz clock frequency classical two wire step direction interface TMC428 driver chain step direction interface common SPI interface for parameterizing of TMC332 and TMC428

ChopSync PWM (FS Mode)

PACKAGE
Gate Control

FBGA144 package 13 x 13 mm RoHS compliant

TMC428 SPI Driver Chain Interface

Sequencer
Step / Direction

SIN LUT (xy / uvw)

PWM (xy / uvw)

SPI (Register Interface)

Control Logic / Register Bank

10 mm

ABN Decoder

3 Encoder position compare units

Current Measurement Control Unit (Ix, Iy / Iu, Iv, Iw / IRMS)

P Controller

ORDER CODE

D E S C R I PT I O N

TMC332-BC Related product: TMC332-Eval

Micro step sequencer, FBGA144 package

Evaluation board for TMC332

www.trinamic.com for detailed information and datasheets

12

POWER DR I V E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T M C 236
M i cr o s t e p D r i v er f o r u p t o 1 . 5A

M A IN CH A R AC T ER IS T IC S
INFO

The TMC236 is a smart power microstepping driver for bipolar stepper motors. It provides an SPI interface as well as the classical analog/ digital control. A full set of protection and diagnostic features makes this device very rugged. The integrated low-RDS-ON TrenchFET power MOSFETs give an extremely high efficiency and allow driving of a high motor current of up to 1.5A per phase without cooling measures even at high environment temperatures. The small footprint and high efficiency make the device a perINTERFACE

full protection and diagnostics low power dissipation 16 times microstepping via SPI, 64 times using additional shift register, even more via analog control mixed decay for smooth operation programmable slope control for low EME internal or external chopper clock standby and shutdown mode easy-to-use SPI interface classical analog interface
ELECTRICAL DATA

fect solution for embedded motion control and even for battery powered designs. The evaluation can be done with the TMC246, as the only difference is the additional stallGuard feature.
PACKAGE

up to 1500 mA coil current (peak) 7V to 34V motor supply (TMC236A) 3.3V or 5V operation for digital part standard PQFP-44 package RoHS compliant

C/CLK

TMC236
OSC

IN A

IN B

2x 4 bit DACs

PWM control & Gate Driver

Coil A

internal Driver Stage

Current monitoring
Step Motor

10 mm

SPI

Control & Diagnostics

PWM control & Gate Driver
Temp / Volt protection
Coil B

ERROR

3.3 / 5V DC 7..34V DC

internal Driver Stage

ORDER CODE

DE S C R I P T I O N

TMC236A-PA TMC428A-EVAL

1.5A driver, PQFP-44 Evaluation board for TMC428, TMC246A and TMC249A with stallGuard

www.trinamic.com for detailed information and datasheets

13

POWER DR I V E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T M C 246
M i cr o s t e p D r i v er f o r u p t o 1 . 5A w i th s t a ll G u a r d

M A IN CH A R AC T ER IS T IC S
INFO

The TMC246 is a smart power microstepping driver for bipolar stepper motors. The integrated unique sensorless stall detection stallGuard makes it a good choice for applications where a reference point is needed, but where a switch cannot be used. The ability to predict an overload makes the TMC246 an optimum choice for drives, where a high reliability is desired. It provides an SPI interface as well as the classical analog / digital control. A full set of protection and diagnostic features makes this device very rugged. The integrated low-RDS-ON TrenchFET power MOSFETs give an extremely high efficiency and allow driving of a high motor current of up to 1.5A per phase without cooling measures even at high environment temperatures. The small footprint and high efficiency make the device a perfect solution for embedded motion control and even for battery
PACKAGE ELECTRICAL DATA INTERFACE

sensorless stall detection StallGuard full protection and diagnostics low power dissipation 16 times microstepping via SPI, 64 times using additional shift register, even more via analog control mixed decay for smooth operation programmable slope control for low EME internal or external chopper clock standby and shutdown mode easy-to-use SPI interface classical analog interface up to 1500 mA coil current (peak) 7V to 34V motor supply (TMC246A) 3.3V or 5V operation for digital part standard PQFP-44 package RoHS compliant

powered designs.

C/CLK

TMC246
OSC

IN A

IN B

2x 4 bit DACs

PWM control & Gate Driver

Coil A

internal Driver Stage

SPI

Control & Diagnostics & Stallguard

10 mm
Current monitoring

Step Motor

ERROR

PWM control & Gate Driver

Coil B

3.3 / 5V DC 7..34V DC

internal Driver Stage

Temp / Volt protection

ORDER CODE

DE S C R I P T I O N

TMC246A-PA TMC428A-EVAL

1.5A driver with stallGuard, PQFP-44 Evaluation board for TMC428, TMC246A and TMC249A with stallGuard

www.trinamic.com for detailed information and datasheets

14

POWER DR I V E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T M C 239
M i cr o s t e p D r i v er f o r E x t e rn a l M OS F E T s for up to 4A

M A IN CH A R AC T ER IS T IC S
INFO

The TMC239 is a smart high current microstepping driver for bipolar stepper motors. It provides an SPI interface as well as the classical analog / digital control. A full set of protection and diagnostic features makes this device very rugged. It directly drives external MOSFETs for currents of up to 4A. (A list of compatible power MOSFETs is given within the datasheet.) This way it reaches an extremely high efficiency and allows driving of a high motor current without cooling measures even at high environment temperatures. With the new chip-scale QFN package a 4A motor driver can be realized on the size of a stamp! The high motor current makes this device ideal for miniaturized highly dynamic and high torque drive systems. The evaluation can be done with the TMC249 as the only difference is the additional stallGuard feature.
ELECTRICAL DATA INTERFACE

full protection and diagnostics low power dissipation 16 times microstepping via SPI, 64 times using additional shift register, even more via analog control mixed decay for smooth operation programmable slope control for low EME internal or external chopper clock standby and shutdown mode easy-to-use SPI interface classical analog interface up to 4000 mA coil current (peak) with just 4 external dual MOSFETS 7V to 34V motor supply (TMC239A), up to 60V using a few add. components higher current / voltage using additional gate drivers 3.3V or 5V operation for digital part
PACKAGE

standard SO28 package chip size QFN32 package RoHS compliant

C/CLK

TMC239
OSC

IN A

IN B

2x 4 bit DACs

PWM control & Gate Driver

Coil A

SPI

Control & Diagnostics

Current monitoring
PWM control & Gate Driver

Step Motor

10 mm

ERROR

3.3 / 5V DC 7..34V DC

Temp / Volt protection

Coil B

ORDER CODE

DE S C R I P T I O N

TMC239A-SA TMC239A-LA Related product: TMC428A-EVAL

4A driver for external MOSFETs, SO28 4A driver for external MOSFETs, QFN32 TMC32NP, TMC32NP2, TMC34NP Evaluation board for TMC428, TMC246A and TMC249A with stallGuard

www.trinamic.com for detailed information and datasheets

15

POWER DR I V E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T M C 249
M i cr o s t e p D r i v er f o r E x t e rn a l M OS F E T s for up to 4A w i th s t a ll G u a r d

M A IN CH A R AC T ER IS T IC S
INFO

The TMC249 is a smart high current microstepping driver for bipolar stepper motors. The integrated unique sensorless stall detection stallGuard makes it a good choice for applications where a reference point is needed, but where a switch cannot be used. The ability to predict an overload makes the TMC249 an optimum choice for drives where a high reliability is desired. It provides an SPI interface as well as the classical analog/ digital control. A full set of protection and diagnostic features makes this device very rugged. It directly drives external MOSFETs for currents of up to 4A. (A list of compatible power MOSFETs is given within the datasheet.) This way it reaches an extremely high efficiency and allows driving of a high motor current without cooling measures even at high environment temperatures. With the new chip-scale QFN package a 4A motor driver can be realized on the size of a stamp! The high motor current makes this device ideal for miniaturized highly dynamic and high torque drive systems.
ELECTRICAL DATA INTERFACE

sensorless stall detection StallGuard full protection and diagnostics low power dissipation 16 times microstepping via SPI, 64 times using additional shift register, even more via analog control mixed decay for smooth operation programmable slope control for low EME internal or external chopper clock standby and shutdown mode easy-to-use SPI interface classical analog interface up to 4000 mA coil current (peak) with just 4 external dual MOSFETS 7V to 34V motor supply (TMC249A), up to 60V using a few add. components higher current / voltage using additional gate drivers 3.3V or 5V operation for digital part
PACKAGE

standard SO28 package chip size QFN32 7x7 mm package RoHS compliant

C/CLK

TMC249
OSC

IN A

IN B

2x 4 bit DACs

PWM control & Gate Driver

Coil A

SPI

Control & Diagnostics & Stallguard

Current monitoring
PWM control & Gate Driver
Coil B

Step Motor

10 mm

ERROR

3.3 / 5V DC 7..34V DC

Temp / Volt protection

ORDER CODE

DE S C R I P T I O N

TMC249A-SA TMC249A-LA Related product: TMC428A-EVAL

4A driver with stallGuard for external MOSFETs, SO28 4A driver with stallGuard for external MOSFETs, QFN32 TMC32NP, TMC32NP2, TMC34NP Evaluation board for TMC428, TMC246A and TMC249A with stallGuard

www.trinamic.com for detailed information and datasheets

16

GATEDRIV E R

I N T E G R A T E D C I R C U ITS

T MC 603
T h r e e P ha s e M o t o r D ri v e r w i t h B L DC B a c k E M F Co m m ut a t i o n ha l l F X a n d Cu r r ent Sensing

M A IN CH A R AC T ER IS T IC S
INFO

The TMC603 is a three phase BLDC motor driver IC for highly compact and energy efficient drive solutions. Control algorithms previously only found in much more complex servo drives can now be realized with a minimum of external components. The TMC603 directly drives 6 external N-channel MOSFETs for motor currents up to 20A and up to 50V. It integrates current measurement without the need for high current sense resistors, and the sensorless commutation circuitry hallFX. Its integrated support for sine commutation as well as for back EMF sensing and commutation saves cost and allows for maximum drive efficiency. Depending on the desired commutation scheme and the bus interface requirements, the TMC603 forms a complete motor driver system in combination with an external 8 bit processor or with a more powerful 32 bit processor. Protection and diagnostic features as well as a step down switching regulator further reduce system cost and increase reliability.
INTERFACE ELECTRICAL DATA

low power dissipation integrated phase current measurement via RDSon of power MOSFETs sensorless back EMF commutation hallFX (hall sensor like signals - phase shift free) integrated break-before-make logic: no special microcontroller PWM hardware required integrated overcurrent / short to GND and undervoltage protection and diagnostics integrated step down switching regulator up to 500mA / 300kHz up to 20A motor current 9V to 50V operating voltage EMV optimized current controlled gate drivers - up to 150mA internal QGD protection: Supports latest generation of power MOSFETs 3.3V or 5V interface QFN52 package 8 x 8 mm RoHS compliant

The TMC603 also supports control of three phase stepper motors

PACKAGE

as well as two phase stepper motors using two devices.

10 mm

ORDER CODE

D E S C R I PT I O N

TMC603-LA Related product: TMC603-Eval

Driver for external 20A MOSFETs, QFN52 package

Evaluation board for TMC603

www.trinamic.com for detailed information and datasheets

17

MOSFETS

I N T E G R A T E D C I R C U ITS

T M C 32 N P- M L P

T M C 32 N P 2-SM 8
C o mp l e m e nt a r y 30 V M OS F E T H a lf B r i dg e / Fu l l Br i d ge

M A IN CH A R AC T ER IS T IC S
INFO

The TMC32NP-MLP is a miniature N & P channel MOSFET complementary pair, ideally suited for motor drive applications. It perfectly complements the TMC239A-LA / TMC249A-LA stepper motor drivers, in order to build a 2A (4 devices) / 4A (8 devices) stepper motor driver the size of a stamp. The TMC32NP2-SM8 is a miniature N & P channel MOSFET full bridge, ideally suited for motor drive applications. It perfectly complements the TMC239A-SA / TMC249A-SA stepper motor drivers, in order to build a 1.5A / 2.5A peak current capability (5 seconds) stepper motor driver on a two layer PCB. Using just one small fullbridge, a DC motor can be operated in four quadrant mode. The evaluation board has different stepper driver MOSFET configurations and allows SPI control via a TMC428A-EVAL board as well as step / direction control using a TMC401.

ELECTRICAL DATA N TYPE

0.12 RDSon max. @ VGS= 10V 0.18 RDSon max. @ VGS= 4.5V ID= 2.9A max. cont. current (MLP) ID= 2.7A max. cont. current (SM8) 30V VBRDSS max. 0.21 RDSon max. @ VGS= -10V 0.33 RDSon max. @ VGS= -4.5V ID= -2.1A max. cont. current (MLP) ID= -2.0A max. cont. current (SM8) -30V VBRDSS max. extremly compact package low on resistance low gate charge stepper motor drives DC motor drives chip size 2x3 mm dual die package MLP 8 pin SOT223 6.7x7 mm package SM8 RoHS compliant

ELECTRICAL DATA N TYPE

HIGHLIGHTS

APPLICATIONS

PACKAGE

D1

D2

TMC32NP -MLP

S1

D1 D1 D2 D2

G1
G1 S1

G2 S2

S2 G2

S1 G1 D1, D2 G2 S2

S4 G4 D3, D4 G3 S3

G3

TMC32NP2 -SM8

G4 D3, D4 S1, S4 D1, D2

S2, S3
G2 G1

10 mm

ORDER CODE

DE S C R I P T I O N

TMC32NP-MLP TMC32NP2-MLP Related product: TMC32NPx-EVAL

Complementary 30V MOSFET half bridge (MLP package) Complementary 30V MOSFET full bridge (SM8 package) These devices ideally complement the TMC239 & TMC249 Evaluation board for TMC401-PI, TMC249A-LA & TMC32NP-MLP, TMC249A-SA & TMC32NP2-SM8 and TMC249A-LA & TMC34NP-PSO

www.trinamic.com for detailed information and datasheets

18

MOSFETS

I N T E G R A T E D C I R C U ITS

T M C 34 N P- P SO
C o mp l e m e nt a r y 30 V M OS F E T H a lf B r i dg e / Fu l l Br i d ge

M A IN CH A R AC T ER IS T IC S
INFO

The TMC34NP-PSO is a miniature N & P channel MOSFET complementary pair, ideally suited for motor drive applications. It perfectly complements the TMC239A-LA / TMC249A-LA stepper motor drivers, in order to build a 4A stepper motor driver the size of a stamp. The evaluation board has different stepper driver MOSFET configurations and allows SPI control via a TMC428A-EVAL board as well as step / direction control using a TMC401.

ELECTRICAL DATA N TYPE

35m RDSon max. @ VGS= 10V 50m RDSon max. @ VGS= 4.5V ID= 7.7A max. cont. current 30V VBRDSS max. 51m RDSon max. @ VGS= -10V 75m RDSon max. @ VGS= -6V ID= -6.4A max. cont. current -30V VBRDSS max. extremly compact package with good thermal properties low on resistance low gate charge stepper motor drives DC motor drives 3.3 x 3.3 mm dual die SMT package PPAK 1212 RoHS compliant

ELECTRICAL DATA P TYPE

HIGHLIGHTS

APPLICATIONS

PACKAGE

G1
G1 S1

TMC34NP -PSO

S1 S2

D D D D

10 mm

G2 S2

G2

ORDER CODE

DE S C R I P T I O N

TMC34NP-PSO Related product: TMC32NPx-EVAL

complementary 30V MOSFET half bridge (PPAK1212 package) These devices ideally complement the TMC239 & TMC249 Evaluation board for TMC401-PI, TMC249A-LA & TMC32NP-MLP, TMC249A-SA & TMC32NP2-SM8 and TMC249A-LA & TMC34NP-PSO

www.trinamic.com for detailed information and datasheets

19

INTEGRAT E D M O T I O N C O N T R O L L E R AND DRIV E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T M C 211
M i cr o s t e p C o nt r o l l er / D ri v e r for up to 0.8A w i th L I N I n t e r fa c e

M A IN CH A R AC T ER IS T IC S
INFO

The TMC211 is a single chip microstepping motor driver and motion controller with integrated sequencer, bipolar stepper motor driver and LIN slave interface. It is specially intended for de-centralized mechatronic functions. A user-programmable OTP memory is integrated to store motor parameters and configuration settings. The TMC211 allows up to four bit of micro stepping and is capable of driving a phase current of up to 800 mA peak. After initialization, it performs all time critical tasks autonomously based on target positions and velocity parameters. Together with an inexpensive microcontroller the TMC211 forms a complete motion control system. For using the evaluation board together with the PC software a USB-2-X interface is needed.
ELECTRICAL DATA INTERFACE

build-in ramp generator for autonomous positioning programmable speed and acceleration on-the-fly alteration of target position up to 16 times microstepping reference switch input read out full protection and diagnostics automatic fast decay and slow decay low power stand-by mode physical and data link layers conform to LIN rev. 1.2 field programmable node addresses up to 800 mA coil current (peak) supply voltage 8V to 29V
PACKAGE

standard SO20 package RoHS compliant

TMC211
REF

Position Controller
3

Decoder Sequencer

PWM regulator

HW address

internal Driver Stage

10 mm

Step Motor
PWM regulator

LIN

Memory

Control & Diagnostics

Sinewave table DACs

internal Driver Stage

8..29V DC

Temperature protection

Oscillator

ORDER CODE

DE S C R I P T I O N

TMC211-SA TMC211-EvalBoard Related product:

Stepper IC with LIN in SO20 package Evaluation board for TMC211 USB-2-X V2 interface converter, TMCM-Motor

www.trinamic.com for detailed information and datasheets

20

INTEGRAT E D M O T I O N C O N T R O L L E R AND DRIV E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T M C 222
M i cr o s t e p C o nt r o l l er / D ri v e r for up to 0.8A w i th I I C I n t e r fa c e

M A IN CH A R AC T ER IS T IC S
INFO

The TMC222 is a single chip micro stepping motor driver and motion controller with integrated sequencer, bipolar stepper motor driver and two wire serial slave interface (IIC). It is specially intended for de-centralized mechatronic functions. A user-programmable OTP memory is integrated to store motor parameters and configuration settings. The TMC222 allows up to four bit of micro stepping and is capable of driving a phase current of up to 800 mA peak. After initialization, it performs all time critical tasks autonomously based on target positions and velocity parameters. Together with an inexpensive microcontroller the TMC222 forms a complete motion control system. For using the evaluation board together with the PC software a USB-2-X interface is needed.
PACKAGE ELECTRICAL DATA INTERFACE

build-in ramp generator for autonomous positioning programmable speed and acceleration on-the-fly alteration of target position up to 16 times microstepping reference switch input read out full protection and diagnostics automatic fast decay and slow decay low power stand-by mode two wire serial interface (IIC bus) field programmable node addresses (32) up to 800 mA coil current (peak) supply voltage 8V to 29V standard SO20 package chip size QFN32 7x7 mm package RoHS compliant

TMC222
REF
HW address
1

Position Controller

Decoder Sequencer

PWM regulator

internal Driver Stage

Step Motor

10 mm

IIC

Memory

Control & Diagnostics

Sinewave table DACs

PWM regulator

internal Driver Stage

8..29V DC

Temperature protection

Oscillator

ORDER CODE

DE S C R I P T I O N

TMC222-SI TMC222-LI TMC222-EvalBoard Related product:

Stepper IC with I2C in SO20 package Stepper IC with I2C in QFN32 package Evaluation board for TMC222 USB-2-X V2 interface converter, TMCM-Motor

www.trinamic.com for detailed information and datasheets

21

INTEGRAT E D M O T I O N C O N T R O L L E R AND DRIV E R F O R S T E P P E R M O T O R S

I N T E G R A T E D C I R C U ITS

T M C 223
M i cr o s t e p C o nt r o l l er / D ri v e r for up to 0.8A w i th I I C I n t e r fa c e a n d S t a l l D e t e ct i o n

M A IN CH A R AC T ER IS T IC S
INFO

The TMC223 is a single chip micro stepping motor driver and motion controller with integrated sequencer, bipolar stepper motor driver and two wire serial slave interface (IIC). It is compatible to the TMC222, but features an additonal sensorless stall detection, eliminating the need for mechanical reference switches. The TMC223 is specially intended for de-centralized mechatronic functions. A user-programmable OTP memory is integrated to store motor parameters and configuration settings. The TMC223 allows up to four bit of micro stepping and is capable of driving a phase current of up to 800 mA peak. After initialization, it performs all time critical tasks autonomously based on target positions and velocity parameters. Together with an inexpensive microcontroller the TMC223 forms a complete motion control system. For using the evaluation board together with the PC software a USB-2-X interface is needed.
PACKAGE ELECTRICAL DATA INTERFACE

sensorless stall detection build-in ramp generator for autonomous positioning programmable speed and acceleration on-the-fly alteration of target position up to 16 times microstepping reference switch input read out full protection and diagnostics automatic fast decay and slow decay low power stand-by mode two wire serial interface (IIC bus) field programmable node addresses (32) up to 800 mA coil current (peak) supply voltage 8V to 29V standard SO20 package chip size QFN32 7x7 mm package RoHS compliant

TMC223
REF

Position Controller
1

Decoder Sequencer

PWM regulator

HW address

internal Driver Stage

10 mm
Step Motor

IIC

Memory

Control & Diagnostics

Sinewave table DACs

PWM regulator

internal Driver Stage

8..29V DC

Temperature protection

Oscillator

Stall Detection

ORDER CODE

DE S C R I P T I O N

TMC223-SI TMC223-LI TMC223-EVAL Related product:

Stepper IC with LIN in SO20 package Stepper IC with I2C in QFN32 package Evaluation board for TMC223 USB-2-X V2 interface converter, TMCM-Motor

www.trinamic.com for detailed information and datasheets

22

EVALUATI O N B O A R D

I N T E G R A T E D C I R C U ITS

T M C 428 A EVA L
1 0 mm

E v al u a t i on B o ar d w i th T M C4 2 8 , TM C 2 4 6A & T MC 2 4 9A a n d s t a l lG u a r d

M A IN CH A R AC T ER IS T IC S
INFO

The TMC428A evaluation board allows you to explore all functions of the TMC428 and to develop your TMC428 applications. It is equipped with the TMC246A and TMC249A motor drivers for high performance motor control. You will learn everything about the usage and features of the chipset and get the possibility to explore your motion control application and to optimize its parameters. The evaluation board comes with a PC software which gives you access to every bit of the TMC428. The TMC428A-Eval is a complete plug and play solution, additionally only a PC, a motor and a power supply are required!

ELECTRICAL DATA

motor coil current 1A RMS (TMC246) and 1A / 2A RMS (TMC249) power supply 12V to 30V DC RS232 interface to PC user CPU board and / or user driver board can be attached via SPI

INTERFACE

FEATURES

PC control or stand alone operation all parameters can be displayed on the PC and modified interactively test specific motion profiles microstep curve can be optimized to match your motor parameters allows to use integrated or external reference switches driver ICs: Trinamic TMC246 and TMC249 allows to evaluate stallGuard allows to evaluate all driver specific settings RoHS compliant

OTHER

TMC428 Eval
REFSwitches
6

REF 1,2,3

Driver
TMC246

Step Motor

RS-232

ATmega8

CLK 8MHz

Motion Controller TMC428

high power

Function keys

Driver
TMC249

10..28V DC

5V Power Supply

3,3 / 5V DC

MOSFET Driver Stage

Step Motor

ORDER CODE

DESCRIPTION

TMC428A-EVAL TMCM-MOTOR

Evaluation board for TMC428, TMC246A and TMC249A with stallGuard Testmotor with 42 mm flange and about 1A maximum coil current

www.trinamic.com for detailed information and datasheets

23

EVALUATI O N B O A R D

I N T E G R A T E D C I R C U ITS

T M C 249- H VHR
E v al u a t io n B o ar d f o r T M C249 w i th H i gh V o l ta g e a nd H igh R e so l u t io n
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMC249-HVHR is an add on-board for the TMC428A-EVAL, which demonstrates operation of the TMC249 with an increased voltage of up to 45V and add-on circuitry for 64 microsteps.

FEATURES

64 times microstepping via SPI sensorless stall detection stallGuard SPI and analog signals on connectors 0.7A / 1.4A RMS coil current 20V to 45V motor supply voltage 3.3V or 5V operation for digital part power supply 12V to 30V DC RoHS compliant

INTERFACE ELECTRICAL DATA

OTHER

TMC249 HVHR
Connect to 428Eval
SPI

8 bit shift Register CD4094 for 64step

TMC249

Zener diode level shifter

MOSFET Driver Stage

Step Motor

20..48V DC

ORDER CODE

D E S C R I PT I O N

TMC249-HVHR

High voltage / high resolution evaluation board for TMC249 as an add-on for TMC428A-EVAL (incl. 10 pin cable)

www.trinamic.com for detailed information and datasheets

24

PRODUCT S E L E C T O R

M O D U LES

M o d u les for stepp er m otors Sta n d a lone opera tion (screw te rmi nal conne c tors or si mi lar )
TMCM-023 TMCM-078 IDX

3-axis step / direction driver 2A / 28.5V 1-axis step / direction driver 7A / 75V 1-axis step / direction driver 5A / 75V with RS-485 1-axis controller / driver 3.5A / 48V with encoder inf. 1-axis controller / driver 3.5A / 48V with encoder inf. 3-axis controller / driver 1.1A / 34V 3-axis controller / driver 2.8A / 28.5V with opt. encoder inf. and opt. CANopen firmware 6-axis controller / driver 1.1A / 34V 6-axis controller / driver 1.1A / 34V with encoder inf. for 19 rack 6-axis controller / driver 1.1A / 34V + data aquisition 6-axis controller / driver 1.4A / 48V

29 31 32 34 39 43 48 49 50 51 52

7505

TMCM-102 MONOpack2 TMCM-310 TMCM-351 TMCM-610 TMCM-611 TMCM-612 SIXpack2

Mo to r mounta ble
TMCM-013-42 TMCM-110-42 TMCM-111-42 TMCM-111-56

1-axis 42mm motor mounted step / direction driver 1.1A / 30V with RS-485 1-axis 42mm motor mounted controller / driver 1.1A / 34 1-axis 42mm motor mounted controller / driver 2.8A / 28.5V 1-axis 56mm motor mounted controller / driver 5.0A / 36V

28 36 37 38

www.trinamic.com for detailed information and datasheets

25

PRODUCT S E L E C T O R

M O D U LES

Fo r m o u nting on base boa rd

TMCM-035 TMCM-101 TMCM-103 TMCM-301 TMCM-302 TMCM-303 TMCM-323 TMCM-341 TMCM-342 TMCM-343

1-axis step / direction or SPI driver 3.5A / 50V 1-axis controller / driver 3A / 28.5V with encoder inf. 1-axis controller / driver 2.0A / 28.5V with encoder inf. and opt. CANopen firmware 3-axis controller for SPI driver 3-axis controller for step / direction driver 3-axis controller / driver 1.1A / 34V 3-axis encoder interface with SPI 3-axis controller for SPI driver with opt. CANopen firmware 3-axis controller for step / direction driver with opt. CANopen firmware 3-axis controller / driver 1.1A / 34V with opt. CANopen firmware

30 33 35 40 41 42 44 45 46 47

M o d u les for BLDC m otors

TMCM-160 TMCM-163 TMCM-170 TMCM-171

1-axis BLDC controller / driver 5A / 40V 1-axis motor mounted BLDC controller / driver 10A / 36V 1-axis motor mounted BLDC servo controller / driver 10A / 48V with encoder inf. 1-axis BLDC servo controller / driver 20A / 48V with encoder inf.

53 54 55 56

M o d u les for piezo m otors

TMCM-090

1-axis piezo motor driver

57

www.trinamic.com for detailed information and datasheets

26

PRODUCT S E L E C T O R

M O D U LES

Base b oards for m odules

BB-035 BB-101 BB-103 BB-160 BB-301 BB-301 S BB-302 BB-303 BB-323 BB-611 TMCM-EVAL

Baseboard for TMCM-035 Baseboard for TMCM-101 Baseboard for TMCM-103 Baseboard for TMCM-160 Baseboard for TMCM-301//TMCM-341 and 3 x TMCM-035 Baseboard for TMCM-301 and 3 x TMCM-035 with 24V I/Os Baseboard for TMCM-302/TMCM-342 Baseboard for TMCM-303/TMCM-343 Baseboard for TMCM-323 and TMCM-302/TMCM-342 or TMCM-303/TMCM-343 Baseboard for TMCM-611 Evaluation baseboard for TMCM-100, TMCM-301/-341, TMCM-302/-342 or TMCM-303/-343

61 58 59 60 62 63 64 65 66 67 68

A ccess oires for m od ules

TMCM-MOTOR

Test motor

69

Sof tware for modules

TMCL-IDE TMCL-PC

PC-Tools: Integrated Development Environment for TMCL (free download) PC based TMCL interpreter for control of multiple modules (free download)

70 71

www.trinamic.com for detailed information and datasheets

27

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 013-42
1 - Ax i s M o to r M ou n t e d S t ep / Di r e c t io n D r iv e r 1 . 1A / 30 V w i th R S -4 8 5

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-013-42 is a step / direction stepper motor driver for integration directly on a 42 mm / NEMA-17 motor. The TMCM013-LA supports 42 mm / NEMA-17 linear actuators. The parameters like motor current and Step resolution can be changed easily using the RS-485 interface with an ASCII protocol (e.g. with Hyperterminal). Also the firmware of the module can be updated via the serial interface. All settings are stored in an internal EEPROM, so that no bus system is required in the application. The module is fully protected and comes with a standalone reference search feature, using the integrated reference

ELECTRICAL DATA

up to 1.1A RMS coil current (1.5A peak) supply voltage 7V to 30V DC two-phase bipolar motors with 0.3A to 1A coil current Step / Direction input (5 24V signal) with up to 350kHz microstep frequency driver disable input RS485 host interface (optional use / use for parameterization) local input for reference switches optically isolated inputs for Step, Direction and Disable up to 256 times adjustable microstep resolution adjustable standby current reference search and turn CW / CCW via RS485 TRINAMIC driver technology: no heatsink required stallGuard for reference search full protection / diagnostics

SUPPORTED MOTORS

INTERFACE

FEATURES

switch input or stallGuard. The module can be used in step-/direction mode, remote controlled via a RS485 interface, or even as an option in a pseudo DC motor mode. The possibility to adjust the micro step resolution delivers either very high accuracy or high speed.

TMCM-013
RS-485

SOFTWARE

ASCII protocol controlled using simple terminal software Piggy back for 42 mm (NEMA-17) motor or NEMA-17 linear actuator (axis protrudes through board) RoHS compliant

Step/Dir

Opto isolation

Sequencer

programmable

Driver
TMC246

Step Motor
REFSwitches

OTHER

7..30V DC

5V Power Supply

ORDER CODE

D E S C R I PT I O N

TMCM-013-42 TMCM-013-42-LA TMCM-013-CABLE

1-axis step / direction driver module 1.1A / 30V 1-axis step / direction driver module 1.1A / 30V for linear actuator Cable loom

www.trinamic.com for detailed information and datasheets

28

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 023
3 - Ax i s S t ep / Di r e c t io n D r iv e r 2 A / 2 8 .5 V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-023 is a simple and very compact step / direction driver for 3 stepper motors. It allows motor control via step and direction signals and automatically goes into a stand by mode. The drivers are very efficient, so that no heatsink is required if operated in room temperature environment. The module can be directly controlled by a PLC or by a step/di-

ELECTRICAL DATA

2.0A RMS coil current (2.8A peak) 7V to 28.5V DC supply voltage two-phase bipolar motors with about 2A coil current (or sligthly more) Step / Direction input (24V signal) (5V upon request) optically isolated inputs for Step and Direction 1/4 or 1/8 step resolution (selected by jumper) (1/16 upon request) up to 245kHz microstep frequency TRINAMIC driver technology: no heatsink required standby current reduction to 0.5A jumper for mixed-decay mode diagnostic LEDs signal failure status RoHS compliant size: 60 x 100 mm

SUPPORTED MOTORS

INTERFACE

FEATURES

rection controller module like the TMCM-302. All drivers operate completely independent. Please request for different motor current, different microstep resolution or different step/direction control voltage.

OTHER

TMCM-023
Step/Dir
Opto isolation

Step sequencer
Step sequencer
Step sequencer

Driver
TMC239

MOSFET Driver Stage

MOSFET Driver Stage

Step Motor

Step/Dir

Opto isolation

Driver
TMC239

Step Motor

Step/Dir

Opto isolation

Driver
TMC239

7..28.5V DC

5V Power Supply

MOSFET Driver Stage

Step Motor

ORDER CODE

D E S C R I PT I O N

TMCM-023

3-axis step / direction driver module 2A / 28.5V

www.trinamic.com for detailed information and datasheets

29

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 035
1 - Ax i s S t ep / Di r e c t io n o r S P I D r iv e r 3 . 5A / 48 V

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-035 is a compact motor driver module for highly dynamic or high-torque axis. It can be combined with the driver-less modules TMCM-301 or TMCM-302, or with any step / direction controller. Its small size and low power dissipation, together with the variety of three different control interfaces, make it an optimum solution for integration on any user board. The board can be connected to a baseboard or customized electronics with a pin connector. Applications are consumer and industrial controls, CNC power stages, lab automatization, robotics, pick- and place machines.

E LE C T RI C A L D A TA

up to 3.5A RMS coil current (5A peak) 14V to 50V DC motor supply voltage 5V DC logic supply voltage two-phase bipolar motors with 0.3A to 3.5A coil current Step / Direction input (TTL/CMOS signal) SPI interface classical analog interface up to 64 times microstepping via SPI 8, 16, 32 or 64 microstep resolution via step / direction interface (32 and 64 microsteps with new version V2.0), high resolution via analog control motor current setting via internal and / or external resistors up to 245kHz microstep frequency TRINAMIC driver technology: No heatsink required StallGuard optional for SPI operation standby current reduction programmable mixed-decay mode for good microstep performance mode

S U P P OR T E D M O T O RS

I N T E RF A C E

F E AT U R E S

SPI Step/Dir classic analog control

5V DC 15..50V DC
high power

Sequencer

Driver
TMC239

MOSFET Driver Stage

Step Motor

low EMC design for ease of use

O T H ER

68 pin connector carries all signals RoHS compliant size: 80 x 50 mm (credit card)

TMCM-035

ORDER CODE

D E S C RI P T I O N

TMCM-035/SG (-option) Related products

OPTIONS

1-axis driver 3.5A / 50V with StallGuard (V2.0) BB-035, BB-301, BB-301S, BB-100

H V

Horizontal pin connector (standard) Vertical pin connector (on request)

www.trinamic.com for detailed information and datasheets

30

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 078
1 - Ax i s S t ep / Di r e c t io n D r iv e r 7A / 75V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-078 is a high power single axis step / direction stepper motor driver. The TMCM-078 can be operated with supply voltages of up to 75V and up to 7A RMS (9.8A peak) motor coil currents. All major parameters can be set via DIP switches. Up to 256 micro-steps are supported for either high accuracy or high speed. The system features sensorless stall detection (stallGuard). The module is fully protected and comes with a stand-alone reference search feature. The housing is based on an aluminium plate which is used as a heatsink. All inputs and outputs are accessible either via screw connectors or by high density (2 mm) JST connectors.

ELECTRICAL DATA

up to 7A RMS coil current (9.8A peak) supply voltage 15V to 75V DC two-phase bipolar stepper motor with 0.7A to 7A RMS coil current differential Step / Direction input driver disable input input for reference switches general purpose input / output optically isolated inputs for Step, Direction and Disable up to 256 micro-step resolution (adjustable) adjustable standby current stallGuard for reference search full protection / diagnostics RS485 host interface for optional use pluggable screw terminal connectors for all signals with high density JST alternative robust aluminum housing RoHS compliant size: 145 x 96 x 33 mm

SUPPORTED MOTORS

INTERFACE

FEATURES

OTHER

TMCM-078
RS-485

Step/Dir

Opto isolation

Motion Controller

programmable

Driver
TMC249

MOSFET Driver Stage

Step Motor

15..75V DC

5V Power Supply

ORDER CODE

D E S C RI P T I O N

TMCM-078 Related products:

1-axis step / direction driver module 75V, 7A USB-2-485

www.trinamic.com for detailed information and datasheets

31

MODULES F O R S T E P P E R M O T O R S

M O D U LES

I DX

7505

1 0 mm

1 - Ax i s S t ep / Di r e c t io n D r iv e r 5A / 75V w i th R S -4 8 5

M A IN CH A R AC T ER IS T IC S
INFO

The IDX 7505 is a small and rugged step-/ direction stepper motor driver system with a supply voltage of up to 75V and up to 5A RMS motor coil current (ratings for IDX 7505; standard IDX ratings are 3.5A and max. 50V). The parameters of the IDX like motor current and Step resolution can be changed easily using the RS-485 interface with an ASCII protocol (e.g. with Hyperterminal). Also the firmware of the module can be updated via the serial interface. All settings are stored in an internal EEPROM, so that no bus system is required in the application. The module is fully protected and comes with a stand-alone reference search feature, using the integrated reference switch input or stallGuard. The motor, switches and power supply can be connected easily with screw terminal connectors. The housing is based on an aluminium plate which is used as a heatsink.

ELECTRICAL DATA

up to 5A RMS coil current (7A peak) supply voltage 12V to 75V DC two-phase bipolar motors with 0.7A to 5A coil current Step / Direction input (5 24V signal) with up to 350kHz microstep frequency driver disable input RS485 host interface (optional use / use for parameterization) local input for reference switches optically isolated inputs for Step, Direction and Disable up to 256 times adjustable microstep resolution adjustable standby current reference search and turn CW / CCW via RS485 stallGuard for reference search full protection / diagnostics ASCII protocol controlled using simpleterminal software Pluggable screw terminal connectors for all signals robust housing RoHS compliant size: 65 x 64 x 24 mm

SUPPORTED MOTORS

INTERFACE

FEATURES

SOFTWARE

OTHER

TMCM-IDX
RS-485

Step/Dir

Opto isolation

Motion Controller

programmable

Driver
TMC249

MOSFET Driver Stage

Step Motor

12..50V DC 12..75V DC

5V Power Supply

ORDER CODE

D E S C R I PT I O N

TMC IDX 7505 Related products:

1-axis step / direction driver 5A / 75V with RS-485 USB-2-485

www.trinamic.com for detailed information and datasheets

32

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 101
1 - Ax i s C o nt r o l le r / Dr i v e r 3 A / 2 8 .5 V w i th E n co d e r In f .

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-101 is a single axis 2-phase stepper motor controller and driver module. The built in encoder feedback makes it an optimum solution for high-reliability drives. It provides a complete motion control solution at a very small size for embedded applications. The board can be connected to a baseboard or customized electronics with a pin connector. The TMCM-101 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. The TMCM-101 can be controlled via the serial UART interface (e.g. using a RS-232 or RS-485 level shifter) or via CAN. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation, are performed on board. The TMCL program can be stored in the on-board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect motor overload or motor stall. The TMCM-101 is compatible to the TMCM-series of credit card sized module, but has an increased height of 70 mm.

ELECTRICAL DATA

up to 3A coil current RMS (4.2A peak) 7V to 28.5V motor supply voltage 5V DC logic supply voltage two-phase bipolar motors with 1A to 3A coil current incremental encoder (2 or 3 channel) RS232, RS485 or CAN 2.0b host interface inputs for reference and stop switches general purpose analog and digital I/Os 64 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) closed loop for highly dependable drives stallGuard for sensorless motor stall detection

SUPPORTED MOTORS

INTERFACE

FEATURES

OTHER

68 pin connector carries all signals RoHS compliant size: 80x70 mm

TMCM-101
CAN

RS-232 or RS-485

Motion Controller
UART
with TMC428

programmable

high power

Driver
TMC249

MOSFET Driver Stage

Step Motor
ABN
10 mm

5V DC 7..28.5V DC

TMCL Memory

Encoder Interface

Encoder

ORDER CODE

D E S C RI P T I O N

TMCM-101 (-option) Related products:

OPTIONS

1-axis controller / driver 3A, 28.5V BB-101

H V

Horizontal pin connector (standard) Vertical pin connector (on request)

www.trinamic.com for detailed information and datasheets

33

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 102
1 - Ax i s C o nt r o l le r / Dr i v e r 3 . 5A / 48 V w i th E n co d e r In f .

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-102 is a single axis 2-phase stepper motor controller and driver module with an aluminium profile for quick and robust mounting. The built in encoder feedback makes it an optimum solution for high-reliability drives. This drive is optimally suited for industrial high-reliability applications. The power stage has very low dissipation when compared to competitors products. Its interface add-on board concept allows for customer specific interface / connector selection. The TMCM-102 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL).

ELECTRICAL DATA

up to 3.5A RMS coil current (5A peak) 18V to 55V motor supply voltage two-phase bipolar motors with 1A to 3.5A coil current incremental encoder (2 or 3 channel, single ended)

SUPPORTED MOTORS

INTERFACE (WITH ADD ON-BOARD)

RS232, RS485, RS422, USB or CAN 2.0b host interface inputs for reference and stop switches general purpose analog and digital I/Os 64 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) closed loop for highly dependable drives stallGuard for sensorless motor stall detection

FEATURES

Using predefined TMCL high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation, are performed on board. The TMCL program can be stored in the on-board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect motor overload or motor stall.
SOFTWARE

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

Soft Stop

Adress switch

RS-485

USB

TMCM-102 Standard add-on board

ABN

optional simple to use ASCII protocol

REF-Switches

optional cmd. set similar to IMS IM483IE

OTHER

CAN
3

RS-422 (RS-232)

I/Os

Motion Controller
with TMC428

programmable

Encoder Interface
high power

RoHS compliant size: 76 x 70 mm

Encoder

TMCM-102
18..55V DC

Driver
TMC249

5V Power Supply

TMCL Memory

MOSFET Driver Stage

Step Motor

ORDER CODE

D E S C R I PT I O N

TMCM-102-IF TMCM-102

1-axis controller / driver 3.5A / 48V with interface add-on board (standard) 1-axis controller / driver 3.5A / 48V (on request)

www.trinamic.com for detailed information and datasheets

34

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 103
1 - Ax i s C o nt r o l le r / Dr i v e r 2 . 0A / 28 . 5 V w i th E n co d e r In f .

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-103 is a single axis 2-phase stepper motor controller and driver module. The built in encoder feedback makes it an optimum solution for high-reliability drives. It provides a complete motion control solution at a very small size for embedded applications. The board can be connected to a baseboard or customized electronics with its pin connectors. The TMCM-103 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. In addition CANopen is available for this product. The TMCM-103 can be controlled via RS-232 and via CAN. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation, are performed on board. The TMCL program can be stored in the on-board EEPROM for stand-alone operation. The firmware of the module can be updated via the RS-232 or the CAN interface. With the StallGuard feature it is possible to detect motor overload or motor stall.

ELECTRICAL DATA

up to 2.0A coil current RMS (2.8A peak) 7V to 28.5V motor supply voltage two-phase bipolar motors with 1A to 2.0A coil current incremental encoder (2 or 3 channel) RS232 and CAN 2.0b host interface inputs for reference and stop switches general purpose analog and digital I/Os dip-switches to adjust CAN-ID 64 times microstepping memory for 2048 TMCL commands ready for CANopen automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) closed loop for highly dependable drives possible stallGuard for sensorless motor stall detection chopSync for high motor velocity 2 x 16 pin connectors carry all signals RoHS compliant size: 43x49.53 mm

SUPPORTED MOTORS

INTERFACE

FEATURES

OTHER

CAN

programmable

Motion Controller
RS-232
TMCM-103
7...28.5V DC

high power

Driver
TMC249

with TMC428
CANopen Address Selector

MOSFET Driver Stage

Encoder Interface

Step Motor

ABN

Encoder

5V Power Supply

TMCL Memory

ORDER CODE

D E S C RI P T I O N

TMCM-103 (-option) Related products:

OPTIONS

1-axis controller / driver 2.8A, 28.5V BB-103

TMCL CANopen

TMCL firmware CANopen firmware

www.trinamic.com for detailed information and datasheets

35

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 110-42
1 - Ax i s M o to r M ou n t e d C o nt r o l le r / Dr i v e r 1 . 1A / 34 V

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-110-42 is an intelligent stepper motor controller and driver module to be mounted directly on a 42 mm flange motor. This module converts the motor into a compact mechatronic device with bus oriented or stand-alone control. The motor, switches, power and the multi purpose I/Os can be connected with small pluggable connectors. The TMCM-110-42 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. The TMCM-110-42 can be controlled via an RS-232, RS-485, I2C or CAN interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed onboard. The TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the optional stallGuard feature it is possible to detect motor overload or motor stall.

ELECTRICAL DATA

up to 1.1A coil current RMS (1.5A peak) 7V to 34V motor supply voltage two-phase bipolar motors with 0.3A to 1.1A coil current RS232, RS485, IC or CAN 2.0b host interface 2 inputs for reference and stop switches 1 general purpose input and 1 output up to 16 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless motor stall detection full step frequencies up to 20kHz dynamic current control TRINAMIC driver technology: no heatsink required stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

SUPPORTED MOTORS

INTERFACE

FEATURES

SOFTWARE

TMCM-110
RS-232 or RS-485 or IIC or CAN
programmable

TMCL Memory

Motion Controller
with TMC428

Driver
TMC246

Step Motor
REFSwitches
OTHER

pluggable JST connectors RoHS compliant size: 42x42 mm

7..30V DC

5V Power Supply

ORDER CODE

D E S C RI P T I O N

TMCM-110-42 (-option) TMCM-110-CABLE

OPTIONS

1-axis controller / driver module 1.1A / 34V Cable loom (3pcs)

232 485 IIC CAN

RS-232 interface RS-485 interface I2C interface CAN interface

www.trinamic.com for detailed information and datasheets

36

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 111-42
1 - Ax i s M o to r M ou n t e d C o nt r o l le r / Dr i v e r 2 . 8A / 28 . 5 V

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-111-42 is an intelligent stepper motor controller and driver module to be mounted directly on a 42 mm flange motor. This dual-PCB module converts the motor into a compact mechatronic device with bus oriented or stand-alone control. The motor, switches, power and the multi purpose I/Os can be connected with small pluggable connectors. The TMCM-111 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. The TMCM-111 can be controlled via an RS-232, RS-485, I2C or CAN interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. The TMCL program can be stored in the on-board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect motor overload or motor stall.

ELECTRICAL DATA

up to 2.8A coil current RMS (4A peak) 7V to 28.5V motor supply voltage two-phase bipolar motors with 1A to 2.8A coil current RS-232, RS-485, IC, or CAN 2.0b host interface 2 inputs for reference and stop switches 1 general purpose input and 1 output high accuracy 64 times microstepping high current for highly dynamic drive memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless motor stall detection full step frequencies up to 20kHz dynamic current control TRINAMIC driver technology: low power dissipation

SUPPORTED MOTORS

INTERFACE

FEATURES

Step/Dir

Sequencer

TMCM-111-42

SOFTWARE

IIC

TMCL Memory
high power

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

RS-232
RS-485
CAN

Motion Controller
with TMC428

programmable

Driver
TMC249

MOSFET Driver Stage

2

Step Motor
OTHER

I/Os

pluggable connectors RoHS compliant size: 42 x 42 mm (2 stacked PCBs)

7..28.5V DC

5V Power Supply

REFSwitches

ORDER CODE

D E S C RI P T I O N

TMCM-111-42 (-option) TMCM-111-42-CABLE

OPTIONS

1-axis 1-axis controller / driver module 2.8A / 28.5V Cable loom for TMCM-111-42 + motor conn.

485 CAN

RS-232, IIC and RS-485 interface RS-232, IIC and CAN interface

www.trinamic.com for detailed information and datasheets

37

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 111-56
1 - Ax i s M o to r M ou n t e d C o nt r o l le r / Dr i v e r 5 . 0A / 36 V

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-111-56 is an intelligent stepper motor controller and driver module to be mounted directly on a 56 mm flange motor. (Mechanical adaptation required please contact TRINAMIC.) This triple-PCB module converts the motor into a compact mechatronic device with bus-oriented or stand-alone control. The switches, interface and the multi purpose I/Os can be connected with small pluggable connectors. The TMCM-111 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. The TMCM-111 can be controlled via an RS-232, RS-485, I2C or CAN interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed onboard. The TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect motor overload or motor stall.

ELECTRICAL DATA

up to 5A coil current RMS (7A peak) 15V to 36V motor supply voltage two-phase bipolar motors with 2A to 5A coil current RS-232, RS-485, IC or CAN 2.0b host interface 2 inputs for reference and stop switches 1 general purpose input and 1 output high accuracy 64 times microstepping high current for highly dynamic drive memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless motor stall detection full step frequencies up to 20kHz dynamic current control TRINAMIC driver technology: low power dissipation

SUPPORTED MOTORS

INTERFACE

FEATURES

SOFTWARE

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

Step/Dir

Sequencer
IIC
RS-232

TMCM-111-56

TMCL Memory
high power

RS-485

Motion Controller
with TMC428

programmable

Driver
TMC249

MOSFET Driver Stage

2

Step Motor

OTHER

pluggable connectors / screw-terminals RoHS compliant diameter: 55 mm (3 stacked PCBs)

I/Os
2

CAN

14..36V DC

5V Power Supply

REFSwitches

ORDER CODE

D E S C RI P T I O N

TMCM-111-56 (-option) TMCM-111-56-CABLE

OPTIONS

1-axis module Cable loom for TMCM-111-56

485 CAN

RS-232, IIC and RS-485 interface RS-232, IIC and CAN interface

www.trinamic.com for detailed information and datasheets

38

MODULES F O R S T E P P E R M O T O R S

M O D U LES

M O NOpack 2
1 - Ax i s C o nt r o l le r / Dr i v e r 3 . 5A / 48 V w i th E n co d e r In f .

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The MONOpack2 2 is a highly integrated stepper motor controller unit in a robust housing. It provides a high motor power and dynamics. A variety of control interfaces and protocols provide a simple means of remote control or stand alone functionality for all purposes. Its optional incremental encoder feedback and a number of protection features makes drives very dependant and reliable.

ELECTRICAL DATA

up to 3.5A RMS coil current (5A peak) supply voltage 12V to 48V up to 406 times microstepping two-phase bipolar motors with 1A to 3.5A coil current optional incremental encoder (2 or 3 channel)

SUPPORTED MOTORS

INTERFACE

A Windows 95/98/ME/NT/2000/XP based PC software is supplied to explore the possibilities of the MONOpack2. When operated in TMCL mode (optional download / firmware update) you can program its stand-alone functionality using simple TMCL commands. In terms of software and current settings the new MONOpack2 is fully compatible to the old MONOpack and MONOpack Lt while providing a number of enhanced features.
SOFTWARE FEATURES

CAN, RS485 and RS232 and step / direction (differential) I/Os: Limit and reference switch inputs incremental encoder input highly dynamic and fast response drive automatic S-shaped ramp generation closed loop for exact position maintenance or positioning check / retry fully protected driver 3 Firmware modes: TMCL based stand-alone mode ASCII terminal mode MONOpack and Lt compatibility mode comes with PC-based demonstration and application development software

Monopack 2
RS-232

TMCL Memory

ABN

Encoder

OTHER

RS-485

CAN

Step/Dir

Complete Motion Controller

with TMC453

programmable

pluggable screw terminal connectors for all signals robust aluminum housing RoHS compatible size: 132 x 130 x 45 mm

high power

Sequencer

Driver
TMC239

MOSFET Driver Stage

Step Motor

14..48V DC

5V Power Supply

ORDER CODE

D E S C R I PT I O N

TMC MONOpack2

1-axis controller / driver 3.5A / 48V with encoder interface

www.trinamic.com for detailed information and datasheets

39

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 301
3 - Ax i s C o nt r o l le r f o r S P I D r i v e rs
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-301 is a triple axis stepper motor controller module for external power drivers with SPI interface. With its very small size it is dedicated to embedded applications. The board can be connected to a baseboard or customized electronics with a pin connector. The TMCM-301 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. The TMCM-301 can be controlled via its serial UART interface (e.g. using a RS-232 or RS-485 level shifter) or via CAN. A user TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation, are performed on board.

ELECTRICAL DATA SUPPORTED MOTORS/ DRIVERS INTERFACE

5V DC logic supply voltage two-phase bipolar motors using external SPI drivers (e.g. TMCM-035 or TMC249) UART (RS-232, RS-485) or CAN 2.0b host interface inputs for reference and stop switches general purpose analog and digital I/Os up to 64 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) supports stallGuard option for sensor-less motor stall detection full step frequencies up to 20kHz dynamic current control can be adapted to any SPI driver type stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

FEATURES

SOFTWARE

TMCM-301
16
I/Os

e.g. TMCM035

Driver
SPI

SPI

Step Motor
OTHER

68 pin connector carries all signals RoHS compliant size: 80 x 50 mm

CAN
RS-232 or RS-485

Motion Controller
with TMC428

programmable

e.g. TMCM035

Driver
SPI

Step Motor

UART
TMCL Memory
6

e.g. TMCM035

Driver

Step Motor

5V DC

REF-Switches

ORDER CODE

D E S C RI P T I O N

TMCM-301 (-option) Related products:

OPTIONS

3-axis controller module with SPI out BB-301, BB-301S, TMCM-EVAL

H V

Horizontal pin connector (standard) Vertical pin connector (on request)

www.trinamic.com for detailed information and datasheets

40

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 302
3 - Ax i s S t ep / Di r e c t io n C o nt r o l le r
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-302 is a triple axis stepper motor controller module for external power drivers with step / direction interface. With its very small size it is dedicated to embedded applications, where de-centralized high power drivers are desired. The board can be connected to a baseboard or customized electronics with a pin connector. The TMCM-302 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation

ELECTRICAL DATA

5V DC logic supply voltage TTL / CMOS step / direction outputs step / direction drivers (e.g. TMC401, TMCM-013, TMCM-023, TMCM-078, IDX7505 or TMCM-171) UART (RS-232, RS-485) or CAN 2.0b host interface inputs for reference and stop switches general purpose analog and digital I/Os three motion controllers for high step frequency memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) high dynamics: step frequencies up to 300kHz 1.8s step pulse length and step to direction delay

SUPPORTED DRIVERS

INTERFACE

FEATURES

rapid and fast development of motion control applications is guaranteed. The TMCM-302 can be controlled via the serial UART interface (e.g. using a RS-232 or RS-485 level shifter) or via CAN. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation, are performed on board. The TMCL operations can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface.
SOFTWARE

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

TMCM-302
16

TMCL Memory

I/Os

e.g. TMCM035

Driver
step/dir

step/dir

Step Motor
Step Motor
Step Motor
OTHER

CAN

RS-232 or RS-485

UART

Motion Controller
with TMC428
6

programmable

3x

e.g. TMCM035

Driver
step/dir

68 pin connector carries all signals RoHS compliant size: 80 x 50 mm

e.g. TMCM035

Driver

5V DC

REF-Switches

ORDER CODE

D E S C RI P T I O N

TMCM-302 (-option) Related products:

OPTIONS

3-axis step / direction controller module BB-302, BB-323-02, TMCM-EVAL, TMCM driver with step / direction input

H V

Horizontal pin connector (standard) Vertical pin connector (on request)

www.trinamic.com for detailed information and datasheets

41

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 303
3 - Ax i s C o nt r o l le r / Dr i v e r 1 . 1A / 34 V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-303 is a compact and versatile triple axis 2-phase stepper motor controller and driver module. It provides a complete motion control solution at a very small size for embedded applications. Using the integrated additional I/Os it even can do complete system control applications. The board can be connected to a baseboard or customized electronics with a pin connector. The TMCM-303 comes with the PC based software development environment TMCL-IDE. Using predefined TMCL (Trinamic Motion Control Language) high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. Host communication is possible via the serial UART interface (e.g. using a RS-232 or RS-485 level shifter) or via CAN. All time critical operations, e.g. ramp calculation are performed on board. A user TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the optional stallGuard feature it is possible to detect overload and stall of the motor.

ELECTRICAL DATA

up to 1.1A coil current RMS (1.5A peak) 7V to 34V motor supply voltage 5V DC logic supply voltage two-phase bipolar motors with 0.3A to 1.1A coil current UART (RS-232, RS-485) or CAN 2.0b host interface inputs for reference and stop switches general purpose analog and digital I/Os up to 16 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard option for sensorless motor stall detection full step frequencies up to 20kHz dynamic current control TRINAMIC driver technology: no heatsink required

SUPPORTED MOTORS

INTERFACE

FEATURES

TMCM-303
16

SOFTWARE

Driver
TMC246
programmable

Step Motor
Step Motor
Step Motor
REF-Switches
OTHER

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included 68 pin connector carries all signals RoHS compliant size: 80 x 50 mm

I/Os

CAN

RS-232 or RS-485

Motion Controller
with TMC428

Driver
TMC246

UART

Driver
TMC246
6

5V DC 7..34V DC

TMCL Memory

ORDER CODE

D E S C RI P T I O N

TMCM-303/SG (-option) Related products:

OPTIONS

3-axis controller / driver 1.1A / 34V with stallGuard BB-303, BB-323-03, TMCM-EVAL

H V

Horizontal pin connector (standard) Vertical pin connector (on request)

www.trinamic.com for detailed information and datasheets

42

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 310
3 - Ax i s C o nt r o l le r / Dr i v e r 1 . 1A / 34 V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-310 is a triple axis 2-phase stepper motor controller and driver module. It provides a complete single board motion control solution at low cost. Using the integrated additional I/Os it even can do complete system control applications. The motors and switches can be connected easily with screw terminals. The connection of the multi purpose I/Os can be done via a dual-in-line pin connector. The TMCM-310 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. The TMCM-310 can be controlled via the RS-232 or the optional CAN interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. A user TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect overload

ELECTRICAL DATA

up to 1.1A coil current RMS (1.5A peak) 8V to 34V supply voltage

SUPPORTED MOTORS

two-phase bipolar motors with 0.3A to 1.1A coil current RS-232 and optional CAN 2.0b host interface inputs for reference and stop switches general purpose analog and digital I/Os up to 16 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard feature for sensorless stall detection full step frequencies up to 20kHz dynamic current control TRINAMIC driver technology: no heatsink required

INTERFACE

FEATURES

SOFTWARE

and stall of the motor.

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

TMCM-310
16

TMCL Memory

Driver
TMC246

Step Motor

OTHER

pluggable / screw terminal connectors RoHS compliant size: 160 x 100 mm

I/Os

RS-232
CAN (option)

Motion Controller
with TMC428

programmable

Driver
TMC246

Step Motor

Driver
6

Step Motor
REF-Switches

7..34V DC

5V Power Supply

TMC246

ORDER CODE

D E S C R I PT I O N

TMCM-310/SG TMCM-310/SG-CAN

3-axis controller / driver module 1.1A / 34V with stallGuard 3-axis controller / driver module 1.1A / 34V with stallGuard and CAN

www.trinamic.com for detailed information and datasheets

43

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 323
3 - Ax i s E n co d e r I n t e r fa c e w i th S P I
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-323 is a triple axis encoder interface module. It extends the three-axis motion control modules for closed loop operation. With its very small size it is dedicated to embedded applications. The board can be connected to a baseboard or to customized electronics with a pin connector. The TMCM-323 interfaces the 3-axis TMCM modules TMCM-301, TMCM-302 or TMCM-303 via SPI. The TMCM-323 contains three real time counters for the incremental encoders so that the actual position data is available without software timing problems.

ELECTRICAL DATA SUPPORTED ENCODERS

5V DC logic supply voltage two or three channel encoders (differential or TTL/CMOS) SPI to host processor resolution option adapts encoder resolution to motor microstep resolution in fast hardware extends TMCM-301, TMCM-302 or TMCM-303 for position feedback (already integrated in the operating system) encoder frequencies up to 4M count/s N-channel event can snapshoot encoder counter 24 bit encoder counter resolution no additional SW required 68 pin connector carries all signals RoHS compliant size: 80 x 50 mm

INTERFACE FEATURES

SOFTWARE OTHER

SPI
Encoder

Motor

e.g. TMCM-301

ABN
5V DC

Encoder Interface
with TMC423

ABN ABN

Encoder

Motor

or

TMCM-302
or

TMCM-323

Encoder

Motor

TMCM-303

ORDER CODE

D E S C RI P T I O N

TMCM-323 (-option) Related products:

OPTIONS

3-axis Encoder BB-323

H V

Horizontal pin connector (standard) Vertical pin connector (on request)

www.trinamic.com for detailed information and datasheets

44

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 341
3 - Ax i s C o nt r o l le r f o r S P I D r i v e rs
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-341 is a triple axis stepper motor controller module for external power drivers with SPI interface (e.g. TMCM-035). With its very small size it is dedicated to embedded applications, where a compact solution is required. The board can be connected to a baseboard or customized electronics with a pin connector. The TMCM-341 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level com-

ELECTRICAL DATA SUPPORTED MOTORS/ DRIVERS INTERFACE

5V DC logic supply voltage two-phase bipolar motors using external SPI drivers (e.g. TMCM-035 or TMC249) UART (RS-232, RS-485, up to 115200 bit/s) or CAN 2.0b host interface (up to 1Mbit/s) or USB (optional) inputs for reference and stop switches general purpose analog and digital I/Os up to 64 times microstepping memory for 2048 TMCL commands ready for CANopen automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) supports stallGuard option for sensor-less motor stall detection full step frequencies up to 20kHz dynamic current control can be adapted to any SPI driver type stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

FEATURES

mands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. The TMCM-341 can be controlled via the serial UART interface (e.g. using a RS-232 or RS-485 level shifter), via CAN or optinal via USB. A user TMCL program can be stored in the on board EEPROM for stand-alone applications. An optional firmware allows to control the TMCM-341 via CANopen. The firmware of the module can be updated via the serial or the CAN interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation, are performed on board.
SOFTWARE

TMCM-341
16

SPI

Step Motor
Step Motor
Step Motor
OTHER

Driver
e.g. TMCM-035

I/Os
programmable
CAN

Motion Controller
with TMC428

SPI

Driver
e.g. TMCM-035
SPI

RS-232 or RS-485
5V DC

68 pin connector carries all signals RoHS compliant size: 80 x 50 mm

UART

TMCL Memory

Driver
6
e.g. TMCM-035

REF-Switches

ORDER CODE

D E S C RI P T I O N

TMCM-341 (-option) Related products:

OPTIONS

3-axis controller module with SPI out BB-301, BB-301S, TMCM-EVAL

H-TMCL V-TMCL H-CANopen V-CANopen

Horizontal pin connector with TMCL firmware Vertical pin connector with TMCL firmware Horizontal pin connector with CANopen firmware Vertical pin connector with CANopen firmware

www.trinamic.com for detailed information and datasheets

45

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 342
3 - Ax i s S t ep / Di r e c t io n C o nt r o l le r
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-342 is a triple axis stepper motor controller module for external power drivers with step / direction interface. With its very small size it is dedicated to embedded applications, where de-centralized high power drivers are desired. The board can be connected to a baseboard or customized electronics with a pin connector. The TMCM-342 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. The TMCM-342 can be controlled via the serial UART interface (e.g. using a RS-232 or RS-485 level shifter), via CAN or optinal via USB. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation, are performed on board. The TMCL operations can be stored in the on board EEPROM for stand-alone operation. An optional firmware allows to control the TMCM-342 via CANopen. The firmware of the module can be updated via the serial or via CAN interface.

ELECTRICAL DATA

5V DC logic supply voltage TTL / CMOS step / direction outputs step / direction drivers (e.g. TMC401, TMCM-013, TMCM-023, TMCM-078, IDX7505 or TMCM-171) UART (RS-232, RS-485, up to 115200 bit/s) or CAN 2.0b host interface (up to 1 Mbit/s) or USB (optional) inputs for reference and stop switches general purpose analog and digital I/Os three motion controllers for high step frequency memory for 2048 TMCL commands ready for CANopen automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) high dynamics: step frequencies up to 300kHz 1.8s step pulse length and step to direction delay

SUPPORTED DRIVERS

INTERFACE

FEATURES

TMCM-342
16

step/dir

Step
SOFTWARE

Driver
e.g. TMCM-035

I/Os
CAN

3x
programmable

Motor
Step Motor
Step Motor
OTHER

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included 68 pin connector carries all signals RoHS compliant size: 80 x 50 mm

RS-232 or RS-485
5V DC

Motion Controller
with TMC428

step/dir

Driver
e.g. TMCM-035
step/dir

UART

TMCL Memory

Driver
6
e.g. TMCM-035

REF-Switches

ORDER CODE

D E S C RI P T I O N

TMCM-342 (-option) Related products:

OPTIONS

3-axis step / direction controller module BB-302, BB-323-02, TMCM-EVAL, TMCM driver with step / direction input

H-TMCL V-TMCL H-CANopen V-CANopen

Horizontal pin connector with TMCL firmware Vertical pin connector with TMCL firmware Horizontal pin connector with CANopen firmware Vertical pin connector with CANopen firmware

www.trinamic.com for detailed information and datasheets

46

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 343
3 - Ax i s C o nt r o l le r / Dr i v e r 1 . 1A / 34 V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-343 is a compact and versatile triple axis 2-phase stepper motor controller and driver module. It provides a complete motion control solution at a very small size for embedded applications. Using the integrated additional I/Os it even can do complete system control applications. The board can be connected to a baseboard or customized electronics with a pin connector. The TMCM-343 comes with the PC based software development environment TMCL-IDE. Using predefined TMCL (Trinamic Motion Control Language) high level commands like move to position or constant rotation rapid and fast development of

ELECTRICAL DATA

up to 1.1A coil current RMS (1.5A peak) 7V to 34V motor supply voltage 5V DC logic supply voltage two-phase bipolar motors with 0.3A to 1.1A coil current UART (RS-232, RS-485, up to 115200 bit/s) or CAN 2.0b host interface (up to 1Mbit/s) or USB (optional) inputs for reference and stop switches general purpose analog and digital I/Os up to 64 times microstepping memory for 2048 TMCL commands ready for CANopen automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless motor stall detection full step frequencies up to 20kHz dynamic current control

SUPPORTED MOTORS

INTERFACE

FEATURES

motion control applications is guaranteed. Host communication is possible via the serial UART interface (e.g. using a RS-232 or RS-485 level shifter), via CAN or optional via USB. All time critical operations, e.g. ramp calculation are performed on board. A user TMCL program can be stored in the on board EEPROM for stand-alone operation. An optional firmware allows to control the TMCM-342 via CANopen. The firmware of the module can be updated via the serial or the CAN interface.
TMCM-343
16

Step

Driver
TMC246

I/Os
programmable

Motor

TRINAMIC driver technology: no heatsink required

SOFTWARE

CAN

Motion Controller
with TMC428

Step

Driver
TMC246

RS-232 or RS-485
7...34V DC
5V DC

UART

Motor

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

Step

TMCL Memory
6

Driver
TMC246

Motor
REF-Switches

ORDER CODE

D E S C RI P T I O N

TMCM-343 (-option) Related products:

OPTIONS

3-axis controller / driver 1.1A / 34V BB-303, BB-323-03, TMCM-EVAL

H-TMCL V-TMCL H-CANopen V-CANopen

Horizontal pin connector with TMCL firmware Vertical pin connector with TMCL firmware Horizontal pin connector with CANopen firmware Vertical pin connector with CANopen firmware

www.trinamic.com for detailed information and datasheets

47

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 351
3 - Ax i s C o nt r o l le r / Dr i v e r 2 . 8A / 24 V O p ti o n a l E n c o de r I n te r f ace O p ti o n a l C A N o pe n F i rm w a re

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-351 is a powerful triple axis 2-phase stepper motor controller/driver module with optional encoder interface. Using the integrated additional I/Os it even can do complete system control applications. The motors and switches can be connected easily with screw or crimp style connectors. The connection of the I/Os, the encoder and SPI can be done via a two row header. The TMCM-351 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. The TMCM-351 can be controlled via RS-232, RS485, CAN or USB interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. A user TMCL program can be stored in the on board EEPROM for stand-alone operation. An optional firmware allows to control the TMCM-351 via CANopen. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect overload and stall of the motor.
Step

ELECTRICAL DATA

up to 2.8A coil current RMS nom. 24V DC supply voltage (28.5V DC max)

SUPPORTED MOTORS

two-phase bipolar motors with up-to 2.8A coil current RS-232, RS-485, CAN 2.0b host and USB serial communication interfaces inputs for reference and stop switches general purpose analog and digital I/Os SPI connector with three chip select signals for I/O extension

INTERFACE

FEATURES

each axis individually programmable closed loop operation with TMCL possible up to 64 times microstepping memory for 2048 TMCL commands motion profile generation in real-time on the fly alteration of motion parameters dynamic current control stallGuard for sensorless stall detection integrated protection TRINAMIC driver technology: low power dissipation, no heatsink required

TMCM-351

high power

Driver
TMC249
programmable
high power

RS232
RS485
USB
CAN
20

MOSFET Driver Stage

Encoder
Motor Step

SOFTWARE

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included optional CANopen firmware (CiA 301, 402) pluggable screw or crimp style connectors RoHS compliant size: 160 x 100 mm

Motion Controller
with TMC428

Driver
TMC249

MOSFET Driver Stage

Encoder
Motor

high power

I/Os
TMCL Memory

Driver
TMC249
3-axes

MOSFET Driver Stage

Step
Encoder

Motor

OTHER

24V

5V Power Supply

Encoder Interface
TMC423
option

ABN

ORDER CODE

D E S C RI P T I O N

TMCM-351 (-option) TMCM-351-E (-opt.)

OPTIONS

TMCM-351 without encoder interface TMCM-351 with encoder interface

TMCL CANopen

with TMCL firmware with CANopen firmware

www.trinamic.com for detailed information and datasheets

48

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 610
6 - Ax i s C o nt r o l le r / Dr i v e r 1 . 1A / 34 V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-610 is a six axis 2-phase stepper motor controller and driver module. It provides a complete single board motion control solution at low cost. Using the integrated additional I/Os it even can do complete system control applications. The motors and switches can be connected easily with screw terminals. The connection of the multi purpose I/Os can be done via a dualin-line pin connector. The TMCM-610 comes with the PC based software development environment TMCL-IDE. Using predefined TMCL (Trinamic Motion Control Language) high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. The TMCM-610 can be controlled via the USB or RS-232 interface. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. A user TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect overload and stall of the motor.

ELECTRICAL DATA

up to 1.1A coil current RMS (1.5A peak) 7V to 34V supply voltage two-phase bipolar motors with 0.3A to 1.1A coil current RS-232 and USB host interface inputs for reference and stop switches general purpose analog and digital I/Os up to 16 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless stall detection full step frequencies up to 20kHz dynamic current control TRINAMIC driver technology: no heatsink required

SUPPORTED MOTORS

INTERFACE

FEATURES

SOFTWARE

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor
OTHER

pluggable / screw terminal connectors RoHS compliant size: 160 x 120 mm

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

RS-232

TMCM-610

USB

Motion Controller
with TMC428

programmable

2x

I/Os

16
16

REFSwitches

7..34V DC

5V Power Supply

TMCL Memory

ORDER CODE

D E S C R I PT I O N

TMCM-610/SG

6-axis controller / driver module 1.1A / 34V with stallGuard

www.trinamic.com for detailed information and datasheets

49

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 611
6 - Ax i s C o nt r o l le r / Dr i v e r 1 . 1A / 34 V w i th E n co d e r In f . for 19 Rack

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-611 is a six axis 2-phase stepper motor controller and driver module for mounting in a 19 inch rack. It provides optional encoder feedback for every motor. The module allows a very high density multi axis control solution at aggressive pricing. The motors and encoders are connected directly via the front panel using 15 pin Mini DSUB connectors. An integrated seven segment status display and two status outputs on the back plane connector allow for quick diagnostics. The TMCM-611 comes with the PC based software development environment

ELECTRICAL DATA

up to 1.1A coil current RMS (1.5A peak) 7V to 34V supply voltage two-phase bipolar motors with 0.3A to 1.1A coil current (plus optional encoder) CAN or RS-485 interface via backplane, 8 address bits set via backplane inputs for reference and stop switches incremental encoder (2 or 3 channel) single ended / filtered inputs

SUPPORTED MOTORS

INTERFACE

FEATURES

TMCL-IDE. It can be controlled via its CAN interface. Using predefined TMCL (Trinamic Motion Control Language) high level commands like move to position or constant rotation rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations are performed on board. A user TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the CAN interface. With the stallGuard feature it is possible to detect overload and stall of the motor.
SOFTWARE

up to 78 axis in one rack (using one busconnector board) integrated display shows error / user status information up to 16 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters stallGuard sensorless stall detection dynamic current control stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor
Encoder Encoder Encoder Encoder Encoder Encoder Encoder

OTHER

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

Mini DSUB 15 connectors combined for motor and encoder, 64 pin for backplane RoHS compliant size: 6U (6HE), 4TE

CAN

TMCM-611

CAN addr

Motion Controller
with TMC428

programmable

2x

REFSwitches

5V DC
7..34V DC

TMCL Memory

with 2 x TMC423

Encoder Interface

6 x ABN

ORDER CODE

D E S C R I PT I O N

TMCM-611/SG-CAN TMCM-611/SG-485 Related products:

6-axis controller / driver module 1.1A / 34V with stallGuard and CAN 6-axis controller / driver module 1.1A / 34V with stallGuard and RS-485 BB-611-1, BB-611-2

www.trinamic.com for detailed information and datasheets

50

MODULES F O R S T E P P E R M O T O R S

M O D U LES

T M C M - 612
6 - Ax i s C o nt r o l le r / Dr i v e r 1 . 1A / 34 V + Da t a Aq u i s i ti o n

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-612 is a six axis 2-phase stepper motor controller and driver module with a high performance data acquisition part. The integrated 8 channel 16 bit ADC converter can be programmed to do a step-synchronous input voltage scan and store values at a high data rate. The module provides a high microstep resolution in order to do very exact positioning and measurement tasks. The measurement results can be transferred to a PC using the high-speed USB interface. A number of analog output channels and digital I/Os can be used to control further instrumentation. This feature set makes the module pre-destined for analytical instruments. The TMCM-612 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). User specific data acquisition extensions are available upon request. The TMCM-612 can be controlled via the high-speed USB interface or via its RS-232 interface.

ELECTRICAL DATA

up to 1.1A coil current RMS (1.5A peak) 12V to 34V supply voltage two-phase bipolar motors with 0.3A to 1.1A coil current RS-232 and USB host interface inputs for reference and stop switches general purpose analog and digital I/Os eight 16 bit ADC inputs (0...10V) eight 10 bit DAC outputs (0...10V) up to 64 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware 500kHz, 16 bit AD converter 128kbyte RAM for data aquisition stallGuard for sensorless motor stall detection full step frequencies up to 20kHz dynamic current control TRINAMIC driver technology: no heatsink required

SUPPORTED MOTORS

INTERFACE

FEATURES

SOFTWARE

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included pluggable connectors RoHS compliant size: 160 x 160 mm

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

Driver
TMC246

OTHER

RS-232
USB

TMCM-612

Motion Controller
with TMC428

programmable

2x

I/Os

16

12
ADC 16Bit

REFSwitches

7..34V DC

5V Power Supply

DATA Ram 128kB

TMCL Memory

DAC 10Bit

ORDER CODE

D E S C R I PT I O N

TMCM-612/SG

6-axis controller/driver and data aquisition module, stallGuard

www.trinamic.com for detailed information and datasheets

51

MODULES F O R S T E P P E R M O T O R S

M O D U LES

S I X pa ck 2
6 - Ax i s C o nt r o l le r / Dr i v e r 1 . 4A / 48 V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The SIXpack2 is a highly integrated stepper motor controller unit in a small and robust housing. Up to six 2-phase motors can be driven independently or with linear interpolation in any combination. With three interface options and integrated drivers it is easily integrated in all kinds of automatization environment where motion control is desired. The SIXpack can be remotecontrolled using a simple command set, which is identical for all inteface options.

ELECTRICAL DATA

up to 1.4A RMS coil current (2A peak) supply voltage 15V to 48V up to 16-times microstepping two-phase bipolar motors with 0.3A to 1.4A coil current CAN, RS-485 and RS-232 I/Os: Limit and reference switch input for each motor, one analog input per motor

SUPPORTED MOTORS

INTERFACE

FEATURES

An assembled cable for motor and reference switch connectors is available as an accessory. In terms of software and current settings the new SIXpack2 is fully upward-compatible to the old SIXpack and QUADpack.
SOFTWARE

highly dynamic and fast response drive on-the-fly change of position and velocity automatic ramp generation linear interpolation of up to 6 axis simple software protocol comes with PC evaluation software robust steel housing RoHS compliant size: 180 x 152 x 35 mm

OTHER

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor

Step Motor

Sixpack 2

MOSFET Driver Stage

MOSFET Driver Stage

MOSFET Driver Stage

MOSFET Driver Stage

MOSFET Driver Stage

MOSFET Driver Stage

RS-232 or RS-485

Driver
TMC239

Driver
TMC239

Driver
TMC239

Driver
TMC239

Driver
TMC239

Driver
TMC239

CAN

15..48V DC

5V Power Supply

Motion Controller
with TMC406
ADC 10Bit

programmable

6
7

REFSwitches

ORDER CODE

D E S C R I PT I O N

TMC SIXpack2 TMC SIXpack2CABLE

6-axis controller / driver unit 1.4A /48V SIXpack 2 motor connector cable

www.trinamic.com for detailed information and datasheets

52

MODULES F O R B L D C M O T O R S

M O D U LES

T M C M - 160
1 - Ax i s BL D C C o nt r o l le r / Dr i v e r 5A / 40V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-160 is a controller / driver module for general brushless DC motor applications. It integrates velocity and torque control as well as a hall sensor based positioning mode. The position resolution depends on the motor, i.e. a standard 8 pole motor gives a motor axis resolution of 15 degrees. The module can be used in stand alone operation or remote controlled via a RS232 or RS485 interface (ordering option). Its small form

ELECTRICAL DATA

up to 5A coil current (airflow might be required if operated cont. above 3A) 12V to 40V motor supply voltage (ask for 48V option)

SUPPORTED MOTORS

three phase BLDC motors with hall sensors from a few watts up to 180W velocity up to 100,000 rpm (el. field) RS232 or RS485 host interface analog and digital control inputs constant velocity drives, constant torque drives or positioning automatic positioning ramp generation on the fly alteration of motion parameters (e.g. position, velocity, acceleration) high efficiency, low power dissipation integrated protection: reverse polarity, overload / overtemperature

INTERFACE

factor (50 x 92 mm) allows for integration onto a user board as a plug-on module or for panel mounting, by connecting flat
FEATURES

ribbon cables to the two 2x13 2.54 mm standard header connectors. Multi-axis drives can be easily realized by integrating multiple modules on one baseboard. For Evaluation and small series the BB-160 baseboard has all needed features. The TMCM160 fits perfectly to the QBL4208 BLDC motors.

SOFTWARE

stand-alone operation or remote controlled operation PC based demonstration software allowssetting of all parameters

classic analog control

TMCM-160
RS-232 or RS-485

OTHER

two 2-row 2.54 mm connectors RoHS compliant size: 50 x 92 mm

Motion Controller

programmable

3-ph MOSFET Driver Stage

BLDC Motor

14..36V DC

5V Power Supply

HALL sensors

ORDER CODE

D E S C RI P T I O N

TMCM-160 (-option) Related products:

OPTIONS

1-axis BLDC controller / driver module 5A / 40V BB-160, QMot QBL4208

232 485

RS-232 interface RS-485 interface

www.trinamic.com for detailed information and datasheets

53

MODULES F O R B L D C M O T O R S

M O D U LES

T M C M - 163
1 - Ax i s Mo t o r Mo u n t e d B L DC C o nt r o l l er / D ri v e r 1 2 A / 3 8V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-163 is a controller / driver module for general brushless DC motor applications. It integrates velocity and torque control as well as a hall sensor based positioning mode. The position resolution depends on the motor, i.e. a standard 8 pole motor gives a motor axis resolution of 15 degrees. The module can be used in stand alone operation or remote controlled via RS-232 or RS-485 interfaces (ordering option). Its small form factor (43 x 43 x 20 mm3) allows for mounting directly at the motor. The TMCM-163 fits perfectly to the QBL4208 BLDC motors.

ELECTRICAL DATA

up to 12A coil current (contact to cooling plane might be required using gap pad) 14V to 38V motor supply voltage NEMA 17 mounting configuration three phase BLDC motors with hall sensors from a few watts up to 360W velocity up to 100,000 rpm (el. field) RS232 or RS485 host interface analog and digital control inputs constant velocity drives, constant torque drives or positioning automatic positioning ramp generation on the fly alteration of motion parameters (e.g. position, velocity, acceleration) high efficiency, low power dissipation integrated protection: overload / overtemperature

SUPPORTED MOTORS

INTERFACE

FEATURES

SOFTWARE

stand-alone operation or remote controlled operation PC-based demonstration software allows setting of all parameters

classic analog control

TMCM-163
RS-232 or RS-485

OTHER

pluggable connectors for interface flat connectors for motor and supply RoHS compliant size: 43 x 43 x 20 mm (two stacked PCBs)

Motion Controller

programmable

3-ph MOSFET Driver Stage

BLDC Motor

14..36V DC

5V Power Supply

HALL sensors

ORDER CODE

D E S C RI P T I O N

TMCM-163 (-option) V2 TMCM-163-CABLE Related products:

OPTIONS

1-axis BLDC controller / driver module 12A / 38V Cable loom for TMCM-163 QMot QBL 4208

232 485

RS-232 interface RS-485 interface

www.trinamic.com for detailed information and datasheets

54

MODULES F O R B L D C M O T O R S

M O D U LES

T M C M - 170
1 - Ax i s Mo t o r Mo u n t e d B L DC S e rv o C o nt r o l le r / Dr i v e r w i th E n co d e r In f . 1 0 A / 4 8V

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-170 is a controller / driver module for high performance servo drives based on brushless DC motors. It gives a high resolution like a stepper motor coupled with the high dynamic, high velocity and high reliability of a BLDC drive. A built-in ramp generator allows parameterized smooth positioning, with an external switch in order to provide for an absolute position reference. Its small form factor allows direct mounting on or into a motor-encoder assembly. The TMCM-170 integrates

ELECTRICAL DATA

up to 10A coil current (contact to cooling plane might be required using gap pad) 12V to 48V motor supply voltage three phase BLDC motors from a few watts up to 500W, optional hall sensors two or three channel encoder attached to mechanical axis min 256 steps resol. velocity up to 100,000 rpm (el. field) CAN and RS-232 or CAN and RS-485 digital input for absolute pos. reference servo drive allows ultra precise and fastpositioning automatic positioning ramp generation with all parameters changable on-the-fly different start-up modes for commutation 1024 entry 10 bit motor sine commutation table high efficiency, low power dissipation integrated protection: reverse polarity, overload / overtemperature

SUPPORTED MOTORS

INTERFACE

a position regulator and a ramp generator, to allow for velocity modes. The module can be remote controlled via an RS-232, RSFEATURES

485 or via a CAN interface (ordering option). The TMCM-170 fits perfectly to the QBL5704 BLDC motors.

SOFTWARE

RS-232 or RS-485

TMCM-170
Motion Controller
programmable

MOSFET Driver Stage

BLDC Motor

stand alone operation (analog control or TMCL program) or remote controlled operation PC-based demonstration software allows setting of all parameters

CAN

14..48V DC

5V Power Supply

Encoder Interface

ABN

OTHER

pluggable connectors for interface RoHS compliant diameter: 61 mm (two stacked PCBs)

Encoder

ORDER CODE

D E S C RI P T I O N

TMCM-170 (-option) TMCM-170-CABLE Related products:

OPTIONS

1-axis BLDC servo controller / driver module 10A / 48V Cable loom for TMCM-170 QMot QBL 5704

232 485

RS232 and CAN interface RS485 and CAN interface

www.trinamic.com for detailed information and datasheets

55

MODULES F O R B L D C M O T O R S

M O D U LES

T M C M - 171
1 - Ax i s B L DC S e rv o C o nt r o l le r / Dr i v e r 2 0 A / 4 8V w i th E n co d e r In f .

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-171 is a controller / driver module for high performance servo drives based on brushless DC motors. It combines the high resolution of a stepper motor coupled with the high dynamic, high velocity and high reliability of a BLDC drive. The motor and switches can be connected easily with pluggable screw terminals. A build-in ramp generator allows parameterized smooth positioning. The TMCM-171 supports BLDC motors with nearly any number of poles and incremental encoders with nearly any resolution. The TMCM-171 integrates a velocity regulator, a position regulator and a ramp generator. The module can be controlled remotely via CAN or RS-485 interface. Additionally, the TMCM171 is equipped with a step direction interface. Stand alone operation (either via TMCL program or via analog control) is also possible. The housing is based on an aluminium plate which is used as a heatsink. The TMCM-171 fits perfectly to the QBL5704 BLDC motors.

ELECTRICAL DATA

up to 20A coil current supply voltage 12V to 48V DC three phase BLDC motors from a few watts up to 1kW, optional hall sensors two or three channel encoders attached to mechanical axis min 256 steps resolution velocity up to 100,000 rpm (el. field) differential Step / Direction input CAN and RS-485 4 user programmable inputs (analog / digital) and 2 digital user programmable outputs (up to 50V/2A)

SUPPORTED MOTORS

INTERFACE

FEATURES

servo drive allows ultra precise and fast positioning automatic positioning ramp generation with all parameters changeable on-the-fly different start-up modes for commutation adaptable 256 entry 10 bit motor sine commutation table high efficiency , low power dissipation stand alone operation (analog or TMCL program) or remote controlled operation PC-based demonstration software allows setting of all parameters

SOFTWARE

RS-232 or RS-485
CAN

TMCM-171
Motion Controller
programmable

MOSFET Driver Stage

BLDC Motor

OTHER

pluggable screw terminal connectors for all signals with a small JST alternative robust aluminum housing RoHS compliant size: 145 x 96 x 33 mm

Step/Dir
14..48V DC

Opto isolation

5V Power Supply

Encoder Interface

ABN

Encoder

ORDER CODE

D E S C RI P T I O N

TMCM-171 Related products:

1-axis BLDC controller / driver module 20A / 48V USB-2-X, QMot QBL 5704

www.trinamic.com for detailed information and datasheets

56

MODULES F O R P I E Z O M O T O R S

M O D U LES

T M C M - 090
1 - Ax i s P i ez o M ot o r D ri v e r 3 k Hz / 48 V
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-090 is a compact piezo motor driver module for high precision and highly dynamic piezo axis. It is specially designed for four phase piezo motors, like the PIEZO MOTOR Piezo Legs. It can be combined with the driver-less modules TMCM-301 or TMCM-302 or with any step/direction controller. The TMCM-323 can be added for encoder feedback. Its small size makes it an optimum solution for integration on any user board. The board can be connected to a baseboard or customized electronics with a pin connector. Applications are optical and analytical instruments. Its high microstep resolution leads to a linear motor resolution of about 2nm per microstep.

ELECTRICAL DATA

up to 3 kHz cont. fullstepping rate (400nF load) 48V DC motor supply voltage 5V DC logic supply voltage Piezo Legs four phase motor Step / Direction input (TTL/CMOS signal) SPI interface up to 2048 times microstepping for highest motor precision supports four different waveforms: omega564, sine1s85, Rhomb, Rhomb F low EME design for the ease of use the module is pin compatible to the TMCM-035, and can be used on a baseboard designed for the TMCM-035 68 pin connector carries all signals RoHS compliant Size: 80 x 50 mm (credit card)

SUPPORTED MOTORS INTERFACE

FEATURES

OTHER

SPI

TMCM-090
high power

Step/Dir
5V DC 48V DC

Sequencer

Driver

Analog Power Stage

Piezo LEGS

ORDER CODE

D E S C RI P T I O N

TMCM-090 (-option) Related products:

OPTIONS

1-axis piezo motor driver 3kHz / 48V BB-035, BB-301, BB-100

H V

Horizontal pin connector (standard) Vertical pin connector (on request)

www.trinamic.com for detailed information and datasheets

57

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 1 01
B a se b o a rd f o r T M C M- 1 0 1

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The BB-101 is designed for the TMCM-101 single axis 2-phase stepper motor controller and driver module with encoder interface. This encoder feedback makes it an optimum solution for high-reliability closed loop drives. The BB-101 gives easy access to all important signals of the TMCM-101. Motor connection, power supply and limit switches are accessible via screw terminals while encoder connection and the I/Os of the TMCM-101 have 2 row RM2.54 industry standard connectors. The integrated switch-mode regulator provides the required 5V supply voltage for the TMCM-101. Thus only one power supply is required. The integrated level shifter enables direct connection to a PC or host controller via different interfaces.

ELECTRICAL DATA

15V to 28V DC power supply up to 3A coil current RMS (4.2A peak) RS-232 (optionally RS-485, CAN) 2x limit switches, all 16 general purpose analog or digital I/Os of the TMCM-101 supported local input 1 slot for TMCM-101 closed loop motion control and driver module, 3A / 28V up to 64 times adjustable microstep resolution integrated 5V power supply stallGuard for reference search screw terminal connectors for power supply, motor and reference switch connection RoHS compliant size: 80 x 60 mm with TMCM-101 plugged in: 80 x 130 mm

INTERFACE

FEATURES

OTHER

16

BB-101
I/Os

ABN

Encoder

CAN

RS-232 or RS-485

TMCM-101

Step Motor
2

15..28.5V DC

5V Power Supply

REF-Switches

ORDER CODE

D E S C RI P T I O N

BB-101 (-option)
OPTIONS

Baseboard for TMCM-101

232 485

RS-232 / CAN interface RS-485 / CAN interface

www.trinamic.com for detailed information and datasheets

58

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 1 03
B a se b o a rd f o r T M C M - 10 3

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The baseboard BB-103 provides a simple setup featuring the TMCM-103 1-axis stepper controller and driver with support for encoder feedback. This encoder feedback makes it an optimum solution for highly reliable closed loop drives. The BB-103 gives easy access to all important signals of the TMCM-103. Motor connection, power supply and encoder connection are accessible via pluggable screw terminals while the I/Os of the TMCM-103 have a 2 row RM2.54 industry standard connector.

ELECTRICAL DATA INTERFACE

24V DC supply voltage Interface: RS-232 or CAN (D-SUB) 2 inputs for reference and stop switches 2 general purpose analog and digital I/Os 2 digital outputs supports one TMCM-103 1-axis stepper controller / driver jumper for differential encoder termination jumper for CAN termination pluggable screw terminal connectors for power supply, motor and encoder reverse voltage / short circuit protection RoHS compliant size: 85 x 71 mm, 24 mm height

FEATURES

OTHER

I/Os

Step

CAN

TMCM-103
Motor

RS-232
7...28.5V DC

BB-103

ABN

Encoder
REF-Switches

ORDER CODE

D E S C RI P T I O N

BB-103

Baseboard for TMCM-103

www.trinamic.com for detailed information and datasheets

59

BASEBOAR D S F O R B L D C M O D U L E S

M O D U LES

B B - 1 60
B a se b o a rd f o r T M CM - 1 6 0

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The baseboard BB-160 allows to build a ready to use BLDC motor driver unit using the TMCM-160 driver module. It integrates velocity and torque (via current) control as well as a hall sensor based positioning mode. The position resolution depends on the motor, i.e. a standard 8 pole motor gives a motor axis resolution of 15 degrees. The module can be used in stand alone operation (analog control) or it can be remotely controlled via RS-232 (or RS-485). All important signals and the power supply lines can be connected easily. For motor, power supply and hall sensors screw terminals are available and for RS232 (or RS485) a 9-pin D-SUB connector. Some signals like the analog inputs are adjustable either onboard or they can be remote controlled.

ELECTRICAL DATA FEATURES

14V to 40V supply voltage fast prototyping of motion control applications with BLDC motors (e.g. lab use) ad-hoc evaluation of the TMCM-160 module without the need for developing a custom PCB BB-160 + TMCM-160 suitable even for series production RS-232 or RS-485 Interface screw connectors for motors and hall sensors for fast prototyping access to all control inputs of the TMCM-160 screw holes for reliable mounting beyond prototyping setting of motor voltage and current by two potentiometers

HIGHLIGHTS

OTHER

RoHS compliant size: 120 x 85 mm

BB-160
RS-232

TMCM-160

BLDC Motor

Motor off

Direction

classic Analog control

14..36V DC

Onboard controls
10V supply

HALL sensors
3 LEDs

ORDER CODE

D E S C R I PT I O N

BB-160

Baseboard for TMCM-160

www.trinamic.com for detailed information and datasheets

60

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 0 35
B a se b o a rd f o r T M C M- 0 3 5

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The baseboard BB-035 allows to build a ready to use stepper driver unit using the TMCM-035 driver module. All important signal and power lines are accessible via screw terminals, the step and direction inputs are equipped with opto couplers. The integrated switch-mode regulator provides the required 5V supply voltage for the TMCM-035.

ELECTRICAL DATA INTERFACE

15V to 50V DC supply voltage optically de-coupled step/direction input (differential / optical) SPI and analog inputs accessible via additional connector

FEATURES

1 slot for TMCM-035 power driver integrated 5V power supply protection: overvoltage suppressor and inverse polarity

OTHER

RoHS compliant size: 90 x 60 mm, 60 mm height

SPI classic analog control Step/Dir

15.. 50V DC

BB-035

TMCM-035
Opto isolation

Step Motor

5V Power Supply

current selection

ORDER CODE

D E S C R I PT I O N

BB-035

Baseboard for TMCM-035

www.trinamic.com for detailed information and datasheets

61

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 3 01
B a se b o a rd f o r o n e T M C M - 30 1 / T M CM - 3 41 a n d u p to 3 T MC M - 0 3 5
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The BB-301 baseboard is designed for the TMCM-301 or TMCM341 stepper controller to operate with up to three TMCM-035 power drivers. It provides a very small and cost effective solution for a motion control application for up to three size 57 mm stepper motors. All motor, switch and power lines are accessible via screw terminals. For the general purpose I/Os there is a dual-in-line pin connector. The integrated switch-mode regulator provides the required 5V supply voltage for the modules. The supply voltage input is protected against wrong polarity. The integrated level shifter enables direct connection to a PC or host controller via different interfaces.

ELECTRICAL DATA INTERFACE

15V to 50V DC supply voltage all options of the TMCM-301 are supported, additionally a USB interface type is available 6 x limit switch, 8 general purpose digital/analog in, 8 general purpose digital out

FEATURES

1 slot for the TMCM-301/TMCM-341 motion control module 3 slots for TMCM-035 power drivers 16 times microstepping for the motors integrated 5V power supply protection: overvoltage suppressor and inverse polarity

OTHER

screw terminal connectors for I/O signals RoHS compliant size: 90 x 87 mm, 60 mm height

20

BB-301
I/Os

TMCM-035

Step Motor

RS-232 or RS-485 or CAN

TMCM-301

TMCM-035
TMCM-035

Step Motor

SPI

Step Motor
REF-Switches

15.. 50V DC

5V Power Supply

ORDER CODE

D E S C RI P T I O N

BB-301 (-option)
OPTIONS

Baseboard for TMCM-301/TMCM-341 + 3x TMCM-035

232 485 CAN USB

RS-232 interface RS-485 interface CAN interface USB interface (on request)

www.trinamic.com for detailed information and datasheets

62

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 3 01 S
B a se b o a rd f o r o n e T M C M - 30 1 a n d u p to 3 T MC M - 0 3 5 w i th 2 4 V I / O s

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The BB-301S baseboard is designed for the TMCM-301 or TMCM341 stepper controller to operate with up to three TMCM-035 power drivers in a 24V industrial environment. It provides a small and cost effective solution for a motion control application for up to three size 57 mm stepper motors. All motor, switch, I/O and power lines are accessible via screw terminals. For each I/O there is a control LED. The integrated switch-mode regulator provides the required 5V supply voltage for the modules. The supply voltage input is protected against wrong polarity. The integrated level shifter enables direct connection to a PC, PLC or host controller via different interfaces. Several options are available.

ELECTRICAL DATA

15V to 50V DC supply voltage seperate +24V supply for I/Os all options of the TMCM-301 are supported 6 x limit switch (two per axis) (24V) 8 general purpose digital/analog in (24V), 8 general purpose digital out (24V, 1A, PNP transistor type output) 2 DAC outputs optional 1 slot for the TMCM-301/TMCM-341 motion control module 3 slots for TMCM-035 power drivers control LED for each input and output 16 microstep motor driver resolution integrated 5V power supply protection: overvoltage suppressor and inverse polarity

INTERFACE

FEATURES

20

I/Os 24V

BB-301S
TMCM-035
TMCM-301

Step Motor
Step Motor
Step Motor
REF-Switches

OTHER

screw terminal connectors for I/O signals RoHS compliant size: 133 x 100 mm, 60 mm height

USB
RS-232 or RS-485 or CAN

TMCM-035

TMCM-035
6

24V DC 24..48V DC

5V Power Supply

ORDER CODE

D E S C RI P T I O N

BB-301S (-option)
OPTIONS

Baseboard for TMCM-301/TMCM-341 + 3x TMCM-035

232 485 USB LAN

2ND OPTION

RS-232 interface RS-485 interface USB interface (on request) LAN/Ethernet interface (on request)
( A D D IT I O N A L )

+A +E

Analog-Outputs (on request) Encoder-Feedback with TMCM-323 (on request)

www.trinamic.com for detailed information and datasheets

63

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 3 02
B a se b o a rd f o r T M C M- 3 0 2 / TM C M - 3 42

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The baseboard BB-302 provides a simple setup featuring the TMCM-302 or the TMCM-342 high performance controller for external power motor driver with step / direction Interface. The step and direction outputs, switch inputs and the power lines are accessible via screw terminals. For the general purpose I/Os there is a dual-in-line pin connector. The step and direction outputs are equipped with differential drivers. The integrated

ELECTRICAL DATA INTERFACE

7V to 37V DC supply voltage all options of the TMCM-302 are supported 6 x limit switch (two per axis) , 8 general purpose digital/analog in, 8 general purpose digital out 5V differential step/direction outputs (can also be used as single ended outputs)

FEATURES

switch-mode regulator provides the required 5V supply voltage for the module. The supply voltage input is protected against wrong polarity. The integrated level shifter enables direct connection to a PC or other host controller.
OTHER

1 slot for the TMCM-302/TMCM-342 motion control module integrated 5V power supply differential step and direction outputs screw terminal connectors for motor control signals RoHS compliant size: 80 x 50 mm, 15 mm height

20

I/Os

BB-302
step/dir step/dir step/dir

SPI
RS-232 or RS-485 or CAN

TMCM-302

Driver Driver e.g. Driver TMCM035

e.g. TMCM035 e.g. TMCM035

Step Step Step 3x Motor Motor Motor

7.. 37V DC

5V Power Supply

REF-Switches

ORDER CODE

D E S C RI P T I O N

BB-302 (-option)
OPTIONS

Baseboard for TMCM-302/TMCM-342

232 485 CAN

RS-232 interface (standard) RS-485 interface CAN interface

www.trinamic.com for detailed information and datasheets

64

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 3 03
B a se b o a rd f o r T M CM - 3 0 3/ T M C M -3 4 3

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The BB-303 provides a simple setup featuring the TMCM-303 or TMCM-343 controller/driver. All important signal and power lines are accessible via screw terminals. The integrated switchmode regulator provides the required 5V supply voltage for the module. The supply voltage input is protected against wrong polarity. The integrated level shifter enables direct connection

ELECTRICAL DATA INTERFACE

7V to 34V DC supply voltage all options of the TMCM-303 are supported, an USB interface is available as an option 6 x limit switch (two per axis) , 8 general purpose digital/analog in, 8 general purpose digital out

FEATURES

to a PC via RS-232 cable (RS-485 or CAN optionally). A USB option is

OTHER

1 slot for the TMCM-303/TMCM-343 motion control and driver module integrated 5V power supply screw terminal connectors for motor signals RoHS compliant size: 80 x 50 mm, 15 mm height

20

I/Os

BB-303
Step Step Step 3x Motor Motor Motor
6

SPI
RS-232 or USB

TMCM-303

7.. 34V DC

5V Power Supply

REF-Switches

ORDER CODE

D E S C RI P T I O N

BB-303 (-option)
OPTIONS

Baseboard for TMCM-303/TMCM-343

232 485 CAN USB

RS-232 interface (standard) RS-486 Interface CAN interface USB interface (on request)

www.trinamic.com for detailed information and datasheets

65

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 3 23
B a se b o a rd f o r T M C M - 32 3 a n d T M C M- 3 0 2 / TM C M - 3 42 o r T M CM - 3 0 3/ T M C M -3 4 3
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The BB-323 provides a simple setup featuring a TMCM high performance controller and the TMCM-323 incremental encoder module. All important signal and power lines are accessible via screw terminals. Encoder input levels are indicated by LEDs. The integrated switch-mode regulator provides the required 5V supply voltage for the modules. The supply voltage input is protected against wrong polarity. The integrated level shifter enables direct connection to a PC via RS-232 cable (RS-485 or CAN on request).

ELECTRICAL DATA INTERFACE

7V to 34V DC supply voltage 5V differential or single ended inputs for the incremental encoder signals 5V differential step/direction outputs (can also be used as single ended outputs) all options of the TMCM controller are supported 6 x limit switch (two per axis) , 8 general purpose digital/analog in, 8 general purpose digital out

FEATURES

1 slot for the TMCM-323 encoder feedback module and 1 slot for the TMCM-302/TMCM-342 motion control module (option -02) or 1 slot for the TMCM-303/TMCM-343 motion control module (option -03) integrated 5V power supply differential step and direction outputs screw terminal connectors for motor control signals and encoder signals RoHS compliant size: 87 x 77 mm, 60 mm height (-02) 96.5 x 79 mm, 60 mm height (-03)

20

I/Os

SPI
RS-232 or RS-485

TMCM-302
6

Driver Driver e.g. Driver TMCM035

step/dir step/dir step/dir

e.g. TMCM035 e.g. TMCM035

Step Step Step 3x Motor Motor Motor

OTHER

BB-323-02
7.. 34V DC

REF-Switches

5V Power Supply

TMCM-323

ABN

3x 3x 3x Encoder Encoder Encoder

20

I/Os

SPI
RS-232, RS-485 or CAN

TMCM-303
6

Step Step Step 3x Motor Motor Motor

REF-Switches
ABN
3x 3x 3x Encoder Encoder Encoder

BB-323-03
7.. 34V DC

5V Power Supply

TMCM-323

ORDER CODE

D E S C RI P T I O N

BB-323 (-option)
OPTIONS

Baseboard for TMCM-323 and TMCM-302/TMCM-342 or TMCM-303/TMCM-343

02 03

Slot for TMCM-302/TMCM-342 controller module Slot for TMCM-303/TMCM-343 controller/driver module

www.trinamic.com for detailed information and datasheets

66

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

B B - 6 11
B a se b o a rd f o r T M C M - 61 1

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The BB-611-1 and BB-611-2 provide a simple setup featuring one and two TMCM-611 6-axis stepper controller and driver with support for encoder feedback. The integrated switch-mode regulator provides the required 5V supply voltage for the modules. The supply voltage input is protected against wrong polarity. The integrated level shifter enables direct connection to a PC via CAN or RS-485 cable.

ELECTRICAL DATA INTERFACE FEATURES

24V DC supply voltage Interface: RS-485 or CAN (D-SUB) one (-1) or two (-2) slots for the TMCM-611 6-axis stepper controller / driver one rotary selector for crate address one (-1) or two (-2) rotary selector for slot address integrated 5V power supply filter capacitors reverse voltage / short circuit protection mounting holes 19 rack (-2) RoHS compliant size: 64 x 100 mm, 60 mm height (-1) 95 x 129 mm, 60 mm height (-2)

OTHER

BB-611-01

RS-485 or CAN

TMCM-611
Address Selector

Step 6x 6x 6x 6x 6x 6x Motor

Encoder 6x Encoder Encoder Encoder Encoder Encoder

24V DC

5V Power Supply

ABN

BB-611-02

TMCM-611
Address

Step 6x 6x 6x 6x 6x 6x Motor

Encoder 6x Encoder Encoder Encoder Encoder Encoder

ABN
Step 6x 6x 6x 6x 6x 6x Motor

RS-485 or CAN

Selector

24V DC

TMCM-611
5V Power Supply
Address Selector

Encoder 6x Encoder Encoder Encoder Encoder Encoder

ABN

ORDER CODE

D E S C RI P T I O N

BB-611 (-option)
OPTIONS

Baseboard for TMCM-611

-1 -2

one slot for TMCM-611 stepper controller / driver two slots for TMCM-611 stepper controller / driver

www.trinamic.com for detailed information and datasheets

67

BASEBOAR D S F O R S T E P P E R M O D U L E S

M O D U LES

T M C M - EVA L
E v al u a t io n B a se b o a r d f o r T M C M- 1 0 0 , T M C M - 30 1 , T M CM - 3 0 2 o r T MC M - 3 0 3
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-EVAL is a baseboard which allows to evaluate the operation of the TMCM-Modules. All interface signals of the respective are available on screw terminal connectors. The inputs can be switched and the outputs are seen via LEDs. An integrated stepper motor driver TMC236 allows the operation of a 2 phase stepper motor when using the TMCM-100 or to the TMCM-301.

ELECTRICAL DATA

single DC supply voltage required (7V to 34V) Interface: RS-232, RS-485, CAN 8 digital/analog inputs (5V), with DIP-switch and screw connectors 8 digital outputs (5V) with control LEDs and screw connectors 2 switch inputs (5V) per axis on screw terminals

INTERFACE

FEATURES

1 slot for TMCM-Module (TMCM-100, -301, -302 or -303) integrated 5V switching voltage regulator 1 axis motor driver with 1.1A/34V (TMC236) used with TMCM-100, -301

OTHER

RoHS compliant size: 160 x 100 mm

8
I/Os

48

Status LEDs

TMCM-EVAL
Output variations depend on Module

RS-232
RS-485

Step Step Step 3x Motor Motor Motor

Step Motor
ABN

TMCM-303

TMC Module
100, 301, 302, or 303

Driver
TMC236

TMCM-100, 301 or 302

CAN

7..28.5V DC

5V Power Supply

22

DIP Switches

Encoder

Encoder for TMCM-100 only

ORDER CODE

D E S C R I PT I O N

TMCM-EVAL or TMCM-Baseboard TMCM-MOTOR

Evaluation baseboard for TMCM-100, TMCM-301, TMCM-302 or TMCM-303 Testmotor: 2-phase hybrid stepper motor with 42 mm flange

www.trinamic.com for detailed information and datasheets

68

ACCESSOR I E S F O R S T E P P E R M O D U L E S

M O D U LES

T M C M - M OTO R
T e st M o to r f o r T M C M M o d ules u p t o 1 .1 A c o il c u r re n t

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The TMCM-MOTOR allows to test the TMCM modules with a coil current of up to 1.1A RMS. The motor is a selected type from running production. Length, axis length and torque, as well as electrical parameters may vary. The modules can be adapted to the actual motor current rating. Please see motor label for actual data.

ELECTRICAL DATA FEATURES

0.8A to 1.2A RMS coil current (may vary) NEMA 17 mounting configuration flange 42.2 mm * 42.2 mm 5 mm axis diameter step angle 1.8 optimized for microstep operation 4 wire connection

ORDER CODE

D E S C R I PT I O N

TMCM-Motor

Testmotor: 2-phase hybrid stepper motor with 42 mm flange

www.trinamic.com for detailed information and datasheets

69

SOFTWARE

M O D U LES

T MC L-I D E
P C T o o l s: I n t e g r a t e d D e v e l o p me n t E n v i r o n me n t f o r T M C L ( T r i n a m i c Mo t i on Control Language)

The TMCL-IDE is an integrated development environment for

INFO

M A IN CH A R AC T ER IS T IC S

developing stand-alone TMCL applications and for configuring TMCM modules. The built-in editor with TMCL syntax highlighting allows comfortable editing of TMCL programs. TMCL programs can be assembled, debugged and downloaded into the module using all possible interfaces (RS232, RS485, USB, CAN or IIC). From version 1.70 the TMCL-IDE has an integrated true inSystem debugging tool. It is also possible to read back TMCL programs from a module for analyzing and modifying them. These features make it easy to develop and test even larger TMCL applications. The TMCL-IDE also contains other powerful tools that make it possible to easily find the best parameters for StallGuard and to calculate velocity and acceleration parameters. The TMCL-IDE comes free of charge with all Trinamic modules and can be downloaded from the website.

powerful TMCL editor with syntax highlighting TMCL assembler and disassembler Direct Mode dialogue for online execution of TMCL commands Configure Module dialogue for setting all important parameters of a module StallGuard Adjusting Tool for trying StallGuard parameters on-line StallGuard Profiler for finding the best StallGuard parameters easily parameter calculation tool that allows to calculate velocity and acceleration parameters easily tool for updating the firmware of a TMCM module integrated true inSystem debugging tool possible interfaces: RS232, RS485 (via RS232-RS485 converter, USB to RS485 converter or USB2X), CAN (via CANnes card or USB2X), IIC (via USB2X), USB (for TMCM-610 or TMCM-612) works with Windows 98, ME, NT4, 2000 and XP free download

ORDER CODE

D E S C R I PT I O N

TMCL-IDE

TMCL Integrated Develpoment Environment (free download)

www.trinamic.com for detailed information and datasheets

70

SOFTWARE

M O D U LES

T MC L- P C
PC based TMCL interpreter for multiple module control

M A IN CH A R AC T ER IS T IC S
INFO

TMCL-PC is a PC based version of the simple-to-use TMCL software. It allows the control of multiple modules via one PC, so that any kind of interaction between the motors and I/Os available on the different modules can be realized. This for example allows the BLDC motor modules to be inter-operated with stepper motor modules.

FEATURES

executes the simple-to-use TMCL commands on a PC can inter-operate any combination of TMCL based modules from a central computer single stepping and debugging mode supports all interface options using the TRINAMIC interface adapters free download

ORDER CODE

D E S C R I PT I O N

TMCL-PC

PC based TMCL interpreter (free download)

www.trinamic.com for detailed information and datasheets

71

PRODUCT S E L E C T O R

I N T E R F A CES

Bus i nte r face conver ters

CANnes USB-2-X USB-2-485

CAN interface PCI card, CAN 2.0b, up to 1Mbit/s USB to CAN, IIC, RS485, SPI and LIN interface converter USB to RS485 interface converter with virtual COM port driver

73 74 75

www.trinamic.com for detailed information and datasheets

72

BUS INTE R F A C E C O N V E R T E R S

I N T E R F A CES

C A Nnes
C A N i n t e rf a c e PCI Card

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The CANnes card is a PCI card which provides a simple, easy to use CAN interface. It is equipped with a male and a female 9 pin Sub-D connector with standard CAN pin assignments. CAN bit rates between 10 and 1000 kBit/s (1MBit/s) are possible. The industry standard CAN controller SJA1000 is used together with the CAN bus driver 82C250 and optical isolation between the CAN controller and the CAN bus driver. A 120 ohms termination resistor is also provided. This resistor can be switched on and off either by a software controlled relay. Device drivers and function libraries are provided for the Windows (98/ME/2000 and NT4) operating systems and also for the Linux operating system. The CANnes cards is CE-approved and also meets FCC specifications. It can be used with every PC which is equipped with PCI slots fulfilling at least the PCI 2.1 standard.

FEATURES

supports CAN V2.0a and V2.0b (11 bit and 29 bit identifiers) CAN bit rates of up to 1Mbit/s 120 ohms termination resistor that can be switched on or off by software

SOFTWARE

simple CAN monitoring software supplied with this product easy programming and integration into user applications via simple DLL functions

OTHER

RoHS compliant

CANnes
PCI-Bus

PCI Bridge

CAN Controller

CAN

ORDER CODE

DESCRIPTION

TMC CANnes

CAN interface PCI-card

www.trinamic.com for detailed information and datasheets

73

BUS INTE R F A C E C O N V E R T E R S

I N T E R F A CES

U SB - 2 -X
USB t o C A N, II C , R S 4 8 5, SP I , LIN I n te r f a c e C o n ve r t e r
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The Engineers Swiss Army Knife for Serial Bus Systems The USB-2-X device is an interface converter that is equipped with a CAN interface, an IIC interface, a LIN interface, an SPI interface and an RS-485 interface. It is connected to the PC via an USB interface. The USB-2-X device is mainly designed for use with some of the Trinamic evaluation kits, but it can also be used in any other purpose where a connection between a PC and a CAN interface, an IIC interface, a LIN interface, an SPI interface or an RS485 interface is needed. The software supplied with this product can be used with every version of the Windows operating system that supports USB (Windows 98, Windows ME, Windows 2000, Windows XP). The USB-2-X device can be connected to USB 1.1 or USB 2.0 hosts and supports the full bitrate of 12MBit/s. It is fully powered by the bus, so no extra power supply is needed.

U SB host interface connection to USB 1.1 or USB 2.0 hosts possible (a cable is included) USB full speed device (12MBit/s) bus powered (no extra power supply needed) C AN CAN 2.0A and 2.0B compatible standard (11 bit) and extended (29 bit) identifier possible transceiver: ISO 11898 compatible maximum bit rate: 1MBit/s 120 ohms termination resistor can be activated with a jumper L IN compatible with LIN specification rev 1.3 up to 20kBit/s Industry standard transceiver IC single master up to 400kBit/s 7-bit addressing RS - 48 5 half duplex communication mode industry standard 75176 transceiver 2400, 9600 and 19200 bps supported S PI master functionality user defined bit rate up to 3.7MBit/s RoHS compliant

USB2X

USB

CAN

IIC

LIN

SPI

RS-485

ORDER CODE

DESCRIPTION

TMC USB-2-X V2

USB interface converter (with USB cable)

www.trinamic.com for detailed information and datasheets

74

BUS INTE R F A C E C O N V E R T E R S

I N T E R F A CES

U SB - 2-485
U S B t o R S4 8 5 I n te r f a c e C o n ve r t e r w i th V i r t ua l C O M P o rt D river
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The USB-2-485 device is a low-cost interface converter that supplies a simple-to-use RS485 interface to a PC with an USB port. The USB-2-485 device can be used erverywhere where an RS485 interface is needed, since it does not require special software. It can be operated with most simple terminal programes supporting the serial interface. The software supplied with this product can be used with every version of the Windows operating system that supports USB (Windows 98, Windows ME, Windows 2000, Windows XP). The USB-2-485 device can be connected to USB 1.1 or USB 2.0 hosts and supports the full bitrate of 12MBit/s. It is fully powered by the bus, so no extra power supply is needed.

U SB host interface connection to USB 1.1 or USB 2.0 hosts possible (a cable is included) USB full speed device (12MBit/s) bus powered (no extra power supply needed) RS 48 5 half duplex communication mode supports all standard baud rates up to 3Mb/s supported Software virtual COM port driver included can be used with standard terminal programs, e.g. Hyperterminal RoHS compliant

USB-2RS485

USB

RS-485

ORDER CODE

DESCRIPTION

TMC USB-2-485

USB interface converter (with USB Cable)

www.trinamic.com for detailed information and datasheets

75

PRODUCT S E L E C T O R

P A Nd r i ves

M e chat roni c drives wi th stepp e r m o to r

PD-108-28 PD-013-42 PD-110-42 PD-111-42 PD-140-42-SE

28 mm stepper motor with controller / driver and serial interface 42 mm stepper motor with step / direction driver 42 mm stepper motor with controller / driver and serial interface 42 mm high perform. stepper motor with controller / driver and serial interface 42 mm high perform. stepper motor with controller / driver and serial interface, integrated sensOstep encoder and optional CANopen firmware

77 78 79 80 81

PD-111-56 PD-109-57 PD-113-57-SE

56 mm high perform. stepper motor with controller / driver and serial interface 57 mm stepper motor with controller / driver and serial interface 57 mm stepper motor with controller / driver with serial interface, integrated sensOstep encoder

82 83 84

PD-113-60-SE

60 mm stepper motor with controller / driver with serial interface, integrated sensOstep encoder

84

PD-116-60-SE

60 mm stepper motor with controller / driver with serial interface, integrated sensOstep encoder and optional CANopen firmware

85

M e chat roni c drives wi th BLCD mo to r

PD-163-42 PD-170-57

42 mm BLDC motor with controller / driver and serial interface 57 mm BLCD encoder motor with controller / driver and serial interface

86 87

www.trinamic.com for detailed information and datasheets

76

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

P D - 108-28
2 8 mm / NE M A 1 1 S t ep p e r M o t o r w i t h C o nt r o l le r / Dr i v e r a n d S e r ia l I n te r f a c e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-108-28 is a full mechatronic solution including a 28 mm flange motor (NEMA11). It joins a convenient controller electronic and a sensOstep encoder with a range of different motor torques. The PD-108-28 offers two motor torque options and can be controlled via RS-485 serial interface. The power supply, interface and the multi purpose I/Os can be connected via a single small JST connectors. The PD-108-28 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept low since all time critical operations, e.g. ramp calculation are performed on board. Full remote control of device with feedback is possible. The firmware of the module can be updated via the serial interface.

ELECTRICAL DATA MOTOR DATA

9V to 28V supply voltage motor length: 32 mm / 51 mm max. torque 0.06 Nm / 0.12 Nm please also refer to the motor datasheet RS-485 2 general purpose inputs 2 general purpose outputs up to 16 times microstepping memory for 64 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) sensOstep Encoder for motor stall detection (e.g. end position reached, overload) dynamic current control stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

INTERFACE

FEATURES

SOFTWARE

PD-108-28

sensOstepTM

Encoder

Encoder

programmable

RS-485

TMCL Interpreter

Motion Controller TMC222

2

TMC222

Driver

Step Motor
Inputs

OTHER

8-pin pluggable JST connectors / cables included RoHS compliant

9..28V DC

5V Power Supply

Outputs

ORDER CODE

D E S C RI P T I O N

PD1-108-28-SE (-option) PD3-108-28-SE (-option)

OPTIONS

PANdrive 0.06 Nm with QSH2818-32-07-006 motor and sensOstep encoder PANdrive 0.12 Nm with QSH2818-51-07-012 motor and sensOstep encoder

485

RS-485 interface

www.trinamic.com for detailed information and datasheets

77

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

P D - 013-42
4 2 mm / NE M A 1 7 S t ep p e r M o t o r w i t h S t ep / Di r e c t io n D r iv e r
1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-013-42 is a full mechatronic solution including a 42 mm flange motor. It joins a convenient controller electronic with a range of different motor torques. The PD-013-42 offers three motor torques options and can be controlled via an optical isolated Step / Direction interface. The power supply, interface and the multi purpose I/Os can be connected with small JST connectors. The firmware of the module can be updated via the serial interface. With the integrated stallGuard feature it is possible to detect overload and stall of the motor.

ELECTRICAL DATA MOTOR TYPES

7V to 30V supply voltage motor length: 53 mm / 59 mm / 69 mm: max. torque 0.27Nm / 0.35Nm / 0.49Nm Step / Direction input (5 24V signal) with up to 350kHz microstep frequency driver disable input RS485 host interface (optional use / use for parameterization) 2 local inputs for reference switches optically isolated inputs for step, direction and disable up to 256 times adjustable microstep resolution adjustable standby current reference move and turn CW / CCW via RS-485 stallGuard for reference search ASCII protocol controlled using simple terminal software pluggable connectors for all signals / cable included RoHS compliant

INTERFACE

FEATURES

SOFTWARE

PD-013-42
RS-485

OTHER

Step/Dir

Opto isolation

Sequencer

programmable

Driver
TMC246

Step Motor
REFSwitches

7..30V DC

5V Power Supply

ORDER CODE

D E S C R I PT I O N

PD1-013-42 PD2-013-42 PD3-013-42

PANdrive 0.27 Nm with QSH4218-35-10-027 motor and step / direction PANdrive 0.35 Nm with QSH4218-41-10-035 motor and step / direction PANdrive 0.49 Nm with QSH4218-51-10-049 motor and step / direction

www.trinamic.com for detailed information and datasheets

78

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

P D - 110-42
4 2 mm / NE M A 1 7 S t ep p e r M o t o r w i t h C o nt r o l le r / Dr i v e r a n d S e r ia l I n te r f a c e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-110-42 is a full mechatronic solution including a 42 mm flange motor. It joins a convenient controller electronic with a range of different motor torques. The PD-110-42 offers three motor torque options and can be controlled via RS-232, RS-485, CAN or IIC interface. The power supply, interface and the multi purpose I/Os can be connected with small JST connectors. The PD-110-42 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. The TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect motor overload or motor stall.
PD-110-42
RS-232 or RS-485 or IIC or CAN
programmable

ELECTRICAL DATA MOTOR DATA

7V to 34V supply voltage total length: 53mm / 59mm / 69mm: max. torque 0.27Nm / 0.35Nm / 0.49Nm please also refer to the motor datasheet RS-232, RS-485, IC or CAN 2.0b host interface 2 inputs for reference and stop switches 1 general purpose input and 1 output up to 16 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless motor stall detection dynamic current control stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

INTERFACE

FEATURES

SOFTWARE

TMCL Memory

OTHER

Motion Controller
with TMC428

Driver
TMC246

Step Motor
REFSwitches

pluggable JST connectors / cables included RoHS compliant

7..30V DC

5V Power Supply

ORDER CODE

D E S C RI P T I O N

PD1-110-42 (-option) PD2-110-42 (-option) PD3-110-42 (-option)

OPTIONS

PANdrive 0.27Nm with QSH4218-35-10-027 motor PANdrive 0.35Nm with QSH4218-41-10-035 motor PANdrive 0.49Nm with QSH4218-51-10-049 motor

232 485 IIC CAN

RS-232 interface RS-485 interface I2C interface CAN interface

www.trinamic.com for detailed information and datasheets

79

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

P D - 111-42
42mm / NEMA17 High Performance Stepper Motor w it h C o nt r o l le r / Dr i v e r a n d S e r ia l I n te r f a c e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-111-42 is a full mechatronic solution including a 42 mm flange high torque motor. Its high motor current allows up to 1200 RPM movement and high precision 64 microsteps. The PD111-42 can be controlled via RS232, IIC, RS485 or CAN interface. The power supply, interface and the multi purpose I/Os can be connected with small JST connectors. The PD-111-42 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. The TMCL program can be stored in the on board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect

ELECTRICAL DATA MOTOR DATA

7V to 28.5V supply voltage total length: 74 mm: max. torque 0.46Nm up to 1200 RPM at 0.25Nm motor uses 2.8A RMS current RS-232, IC, RS-485 or CAN 2.0b host interface 2 inputs for reference and stop switches 1 general purpose input and 1 output up to 64 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless motor stall detection dynamic current control stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

INTERFACE

FEATURES

SOFTWARE

motor overload or motor stall.

Step/Dir

Sequencer

PD-111-42

OTHER

IIC

TMCL Memory
high power

pluggable JST connectors / cables included RoHS compliant

RS-232
RS-485
CAN

Motion Controller
with TMC428

programmable

Driver
TMC249

MOSFET Driver Stage

2

Step Motor

I/Os

7..28.5V DC

5V Power Supply

REFSwitches

ORDER CODE

D E S C RI P T I O N

PD-111-42 (-option)
OPTIONS

PANdrive 0.46 Nm with high speed motor

485 CAN

RS-485, RS-232 and I2C interface CAN, RS-232 and I2C interface

www.trinamic.com for detailed information and datasheets

80

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

P D - 140-42 -S E
4 2 mm / NE M A 1 7 S t ep p e r M o t o r w i t h C o nt r o l le r / Dr i v e r , E n co d e r a n d S e ri a l In t e r f ac e O p ti o n a l C A N o pe n

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PANdrive PD-140-42-SE is a mechatronic solution including a 42 mm flange motor, a controller board and a sensOstep encoder. It offers four motor torque options and can be controlled via CAN, RS-232, RS-485 or USB interface. Power supply, interface and multi purpose I/Os can be connected with small JST connectors. The chopSync feature allows high speed movement avoiding resonances. The PD-140-42-SE comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. The TMCL program can be stored in the onboard EEPROM for stand-alone operation. An optional firmware allows to control the PANdrive via CANopen.

ELECTRICAL DATA MOTOR DATA INTERFACE

7V to 28.5V supply voltage holding torque 0.22 / 0.36 / 0.44 / 0.70 Nm CAN 2.0b (up to 1Mbit/s) host, RS232 or RS485 interface and USB interface two inputs for reference and stop switches two 24V compatible general purpose inputs and two open-collector outputs

FEATURES

integrated sensOstep encoder for position identification and stall detection chopSync for high speed movement up to 16 times microstepping memory for 2048 TMCL commands motion profile calculation in hardware (RT) on the fly alteration of motion parameters (e.g. position, velocity, acceleration) dynamic current control stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

SOFTWARE

CAN or RS-232 or RS-485

USB
24V

PD-140-42-SE
programmable

TMCL Memory
high power

Motion Controller
with TMC428

Driver
TMC249

MOSFET Driver Stage

Step Motor
OTHER

optional CANopen firmware (CiA 301, 402) pluggable JST connectors / cables included RoHS compliant

sensOstep Encoder

5V Power Supply

ORDER CODE

D E S C RI P T I O N

PD1-140-42-SE (-option) PD2-140-42-SE (-option) PD3-140-42-SE (-option) PD4-140-42-SE (-option)

INTERFACE O P T I ON S

PANdrive 0.22 Nm, 48 mm length with QSH4218-34-20-022 motor PANdrive 0.36 Nm, 52 mm length with QSH4218-38-20-036 motor PANdrive 0.44 Nm, 61 mm length with QSH4218-47-20-044 motor PANdrive 0.70 Nm, 74 mm length with QSH4218-60-20-070 motor

232 485 CAN CANopen

USB & RS-232 interface (TMCL firmware) USB & RS-485 interface (TMCL firmware) USB & CAN interface (TMCL firmware) USB & CAN interface (CANopen firmware)

www.trinamic.com for detailed information and datasheets

81

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

P D - 111-56
5 6 mm / NE M A 2 3 H i gh P e rf o r m a nc e S t ep p e r M o t o r w i t h w i th C o nt r o l l er / D ri v e r a n d S e r ia l I n te r f a c e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-111-56 is a full mechatronic solution including a 56mm flange high torque motor. The low resistance of the motor coils and the supported high motor current allows highly dynamic operation. The driver electronics supports up-to 64 micro-steps. The PD-111-56 can be controlled via RS-232, IIC, RS-485 or CAN, interfaces. For connection of power supply and motor coils screw connectors are available. Communication interfaces and multi purpose I/Os can be connected via small JST connectors. The PD-111-56 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed on board. The TMCL program can be stored in the on board EEPROM for stand-alone operation. With the stallGuardTM feature it is possible to detect motor overload or motor stall.

ELECTRICAL DATA

15V to 36V supply voltage 5A RMS nominal motor current (7A peak) total length 85mm max. torque 0.78Nm up to 1200 RPM at 0,56Nm 5A RMS max. coil current RS-232, RS-485 or CAN 2.0b, I2C two inputs for reference and stop switches 1 general purpose input and output high accuracy 64 times micro-stepping high current for highly dynamic drive EEPROM for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuardTM for sensorless motor stall detection full step frequencies up to 20kHz dynamic current control stand alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

MOTOR DATA

INTERFACE

FEATURES

SOFTWARE

Step/Dir

Sequencer

PD-111-56

IIC

TMCL Memory
high power

RS-232
RS-485
CAN

Motion Controller
with TMC428

programmable

Driver
TMC249

MOSFET Driver Stage

2

Step Motor
OTHER

I/Os

pluggable JST connectors / cables included RoHS compliant

14..37V DC

5V Power Supply

REFSwitches

ORDER CODE

D E S C RI P T I O N

PD-111-56 (-option)
OPTIONS

PANdrive 0.78 Nm with high speed motor

485 CAN

RS-232, I2C and RS-485 interface RS-232, I2C and CAN interface

www.trinamic.com for detailed information and datasheets

82

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

PD - 10 9 -5 7
5 7 m m / N E M A2 3 S t e pp e r M o to r w i t h C o n tr o l l e r / D r i v er a n d S e r i a l I n t e r f ac e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-109-57 is a full mechatronic solution including a 57 mm flange motor (NEMA23). It combines a convenient controller electronic with a range of different motor types. The PD-109-57 offers three motor torque options and can be controlled via RS-232 or RS-485 interface. The power supply, interface and the multi purpose I/Os can be connected via two pluggable screw connectors. The PD-109-57 comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed onboard. The TMCL program can be stored in the on-board EEPROM for stand-alone operation. The firmware of the module can be updated via the serial interface. With the stallGuard feature it is possible to detect motor overload or motor stall.

EL EC TR I CA L DA T A

18V to 55V supply voltage 3A RMS nominal motor current (5A peak possible)

MO TO R D AT A

total length: 71 mm / 85 mm / 108 mm: max. torque 0.47Nm / 0.98Nm / 1.63Nm please also refer to the motor datasheet RS232 and RS485 host interface 2 inputs for reference and stop switches 1 general purpose input and 1 output up to 16 times microstepping memory for 2048 TMCL commands automatic ramp generation in hardware on the fly alteration of motion parameters (e.g. position, velocity, acceleration) stallGuard for sensorless motor stall detection optically isolated inputs dynamic current control stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

I NT E RF AC E

FE A TU RE S

SO F TW AR E

PD-109-57
Step/Dir
Opto isolation

TMCL Memory
programmable
high power

RS-232

Motion Controller
with TMC428

Driver
TMC249
I/Os

MOSFET Driver Stage

2

Step Motor

O T HE R

pluggable screw terminal connectors for all external signals RoHS compliant

RS-485

18..55V DC

5V Power Supply

REFSwitches

O RDE R COD E

DE SCRIP TION

PD1-109-57 (-option) PD2-109-57 (-option) PD3-109-57 (-option)

O PTI ON S

PANdrive 0.47 Nm with motor QSH5718-41-30-047 PANdrive 0.98 Nm with motor QSH5718-55-30-098 PANdrive 1.63 Nm with motor QSH5718-79-30-163

RS CAN

RS-232 and RS-485 interface CAN interface (ask for availability)

www.trinamic.com for detailed information and datasheets

83

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

PD - 11 3 -5 7 -S E PD - 11 3 -6 0 -S E
1 0 mm

5 7 m m / N E M A2 3 o r 6 0 m m / N E M A2 4 S t e pp e r M o to r w i t h C o n tr o l l e r / D r i v er , w i t h E n c o d er a n d S e r ia l I n t er f a c e

M A IN CH A R AC T ER IS T IC S
INFO

The PD-113-57/60-SE is a full mechatronic solution including a 57 or 60 mm flange motor (NEMA23/NEMA24). It combines a convenient controller electronic and a sensOstep encoder with a range of different motor types and can be controlled via RS-232 or RS485 interface. The chopSync feature allows high velocity operation avoiding resonances. The PD-113-57/60-SE comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed onboard.

EL EC TR I CA L DA T A

nom. 24V DC supply voltage (28.5V max.) up to 2.8A RMS coil current please also refer to the motor datasheet RS232 or RS485 interface 2 inputs for reference switches 2 general purpose inputs (+24V compatible) 2 general purpose outputs (open-collector) sensOstep encoder (max. 256 incr./rot.) chopSync for high velocity operation stallGuard for motor stall detection up to 16 times microstepping memory for 2048 TMCL commands motion profile calculation in real-time on the fly alteration of motion parameters dynamic current control integrated protection

MO TO R D AT A I NT E RF AC E

FE A TU RE S

PD-113-57/60-SE
RS232 or RS485
24V
programmable

TMCL Memory

Motion Controller
with TMC428

high power

Driver
TMC249

MOSFET Driver Stage

Step Motor

SO F TW AR E

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included

5V Power Supply

sensOstep Encoder
O T HE R

RoHS compliant

O RDE R COD E

DE SCRIP TION

PD1-113-57-SE (-option) PD2-113-57-SE (-option) PD1-113-60-SE (-option) PD2-113-60-SE (-option) PD3-113-60-SE (-option) PD4-113-60-SE (-option)
O PTI ON S

PANdrive 0.55 Nm, 65 mm length with motor QSH5718-41-28-055 PANdrive 1.01 Nm, 75 mm length with motor QSH5718-51-28-101 PANdrive 1.10 Nm, 69 mm length with motor QSH6018-45-28-110 PANdrive 1.65 Nm, 80 mm length with motor QSH6018-56-28-165 PANdrive 2.10 Nm, 89 mm length with motor QSH6018-65-28-210 PANdrive 3.10 Nm, 110 mm length with motor QSH6018-86-28-310

232 485

RS232 interface RS485 interface

www.trinamic.com for detailed information and datasheets

84

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

PD - 11 6 -6 0 -S E
6 0 m m / N E M A2 4 S t e pp e r M o to r w i t h C o n tr o l l e r / D r i v er , w i t h E n c o d er a n d S e r ia l I n t er f a c e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-116-60-SE is a full mechatronic solution including a 60 mm flange motor (NEMA24). It combines a convenient controller electronic and a sensOstep encoder with a range of different motor types. The PD-116-60-SE offers four motor torque options and can be controlled via RS-232 or CAN interface. Power supply, RS232 interface and multi purpose I/Os can be connected via a 15-pin D-Sub connector and CAN via a 9-pin D-Sub connector. The chopSync feature allows high speed movement avoiding resonances. The PD-116-60-SE comes with the PC based software development environment TMCL-IDE for the Trinamic Motion Control Language (TMCL). Using predefined TMCL high level commands like move to position or constant rotation a rapid and fast development of motion control applications is guaranteed. Communication traffic is kept very low since all time critical operations, e.g. ramp calculation are performed onboard. The TMCL program can be stored in the on-board EEPROM for stand-alone operation. An optional firmware allows to control the PD-116-60-SE via CANopen. The firmware of the module can be updated via the serial interface.

EL EC TR I CA L DA T A

nom. 24V DC supply voltage (28.5V max.) up to 2.8A RMS coil current holding torque 1.10 / 1.65 / 2.10 / 3.10 Nm please also refer to the motor datasheet CAN 2.0b (up-to 1Mbit/s) and RS232 interface five 24V compatible inputs (stop- and homeswitch) and 3 open-collector outputs

MO TO R D AT A

I NT E RF AC E

FE A TU RE S

sensOstep encoder (max. 4096 incr./rot.) chopSync for high velocity operation stallGuard for motor stall detection up to 64 times microstepping memory for 2048 TMCL commands rotary switches to adjust CAN-ID motion profile calculation in real-time on the fly alteration of motion parameters dynamic current control integrated protection TRINAMIC driver technology: low power dissipation, no heatsink required

SO F TW AR E

stand-alone operation using TMCL or remote controlled operation PC-based application development software TMCL-IDE included optional CANopen firmware (CiA 301, 402) 15-pin D-Sub connector (male) 9-pin D-Sub connector (male) RoHS compliant

PD-116-60-SE
CAN
programmable

TMCL Memory

RS232
Address Selector

Motion Controller
with TMC428

high power

Driver
TMC249

MOSFET Driver Stage

Step Motor
O T HE R

24V

5V Power Supply

sensOstep Encoder

O RDE R COD E

DE SCRIP TION

PD1-116-60-SE (-option) PD2-116-60-SE (-option) PD3-116-60-SE (-option) PD4-116-60-SE (-option)

O PTI ON S

PANdrive 1.10 Nm, 77 mm length with motor QSH6018-45-28-110 PANdrive 1.65 Nm, 88 mm length with motor QSH6018-56-28-165 PANdrive 2.10 Nm, 97 mm length with motor QSH6018-65-28-210 PANdrive 3.10 Nm, 118 mm length with motor QSH6018-86-28-310

TMCL CANopen

with TMCL firmware with CANopen firmware

www.trinamic.com for detailed information and datasheets

85

MECHATRO N I C D R I V E S W I T H S T E P P E R M O T O R

P A Nd r i ves

P D - 163-42
42mm / NEMA17 High Performance BLDC Motor w i th C o nt r o l le r / Dr i v e r a n d S e r ia l I n te r f a c e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-163-42 is a full mechatronic solution including a 42 mm brushless DC motor (NEMA 17). It combines a convenient BLDC controller/driver electronic (TMCM-163-42) with a range of different motor types with internal HALL sensor. The PD-163-42 offers two motor torque options and can be controlled via RS232 or RS485 interface. Power supply and motor coils are connected via flat connectors and communication interface and the multi-purpose I/Os can be connected via high density JST connectors. It integrates a PID-regulator for velocity control. In addition, the module supports positioning based on the motors hall sensor information.

ELECTRICAL DATA

12V to 38V supply voltage up to 12A coil current total length: 81 mm / 100 mm + module rated torque 0.185 Nm / 0.25 Nm max. peak torque 0.56 Nm / 0.75 Nm nominal 4000 RPM at rated torque number of poles: 8 please also refer to the motor datasheet RS-232 or RS-485 interface on the fly alteration of motion parameters (e.g. position, velocity, acceleration) remote controlled using TMCL commands high efficiency, low power dissipation electronics integrated protection: overload / overtemperature

MOTOR DATA

INTERFACE FEATURES

SOFTWARE

stand-alone (analog) operation or remote controlled operation PC-based demonstration software allows setting of all parameters

OTHER

pluggable conectors RoHS compliant

classic analog control

PD-163-42

RS-232 or RS-485

programmable

Motion Controller

3-ph MOSFET Driver Stage

HALL sensors

BLDC Motor

12V ...39V

5V Power Supply

ORDER CODE

D E S C RI P T I O N

PD3-163-42 (-option) PD4-163-42 (-option)

OPTIONS

PANdrive 0.185 Nm with BLDC motor PANdrive 0.250 Nm with BLDC motor

232 485

RS-232 interface RS-485 interface

www.trinamic.com for detailed information and datasheets

86

MECHATRO N I C D R I V E S W I T H B L D C M O T O R

P A Nd r i ves

P D - 170-57
5 7 mm d i am e t e r B L DC E n co d e r Mo t o r wi t h C o nt r o l le r / Dr i v e r a n d S e r ia l I n te r f a c e

1 0 mm

M A IN CH A R AC T ER IS T IC S
INFO

The PD-170-57 is a full mechatronic solution including a 57 mm brushless DC motor. It combines a convenient servo controller electronic (TMCM-170) and an optical encoder with a range of different motor types. The PD-170-57 offers two motor torque options and can be controlled via RS232, RS485 or CAN interface. The power supply can be connected via screw connectors and the interface and the multi-purpose I/Os can be connected via high density JST connectors. This PANdrive combines the high resolution commonly known from stepper motors with the high dynamic, high velocity and high reliability of a BLDC drive. It integrates a position regulator and a ramp generator. The ramp generators supports parameterized smooth positioning also with an external switch in order to support an absolute position reference.

ELECTRICAL DATA

12V to 48V supply voltage up to 10A coil current total length: 144 mm / 156 mm rated torque: 0.32 / 0.42 Nm number of poles: 4 please also refer to the motor datasheet RS-232, RS-485 or CAN 2.0b host interface servo drive allows ultra precise and fast positioning automatic positioning ramp generation with all parameters changeable on-the-fly different start up-modes for commutation and initialization high efficiency, low power dissipation electronics integrated protection: reverse polarity, overload / overtemperature

MOTOR DATA

INTERFACE

FEATURES

RS-232 or RS-485

PD-170-57
Motion Controller
programmable

3 channel encoder with 500 CPR giving a resolution of 2000 positions per revolution
MOSFET Driver Stage

BLDC Motor

SOFTWARE

CAN

stand alone operation (analog control or TMCL program) or remote controlled operation PC-based demostration software allows setting of all parameters

14..48V DC

5V Power Supply

Encoder Interface

Encoder
OTHER

Pluggable connectors for interface RoHS compliant

ORDER CODE

D E S C RI P T I O N

PD4-170-57-E (-option) PD5-170-57-E (-option)

OPTIONS

BLDC servo module with motor QBL5704-94-04-032 BLDC servo module with motor QBL5704-116-04-042

232 485

RS-232 and CAN interface RS-485 and CAN interface

www.trinamic.com for detailed information and datasheets

87

PRODUCT S E L E C T O R

M O T ORS

QM o t s tepper motors 2818 4218 5718 6018 8618

28 mm / NEMA11, 1.8 step angle 42 mm / NEMA17, 1.8 step angle 57 mm / NEMA23, 1.8 step angle 60 mm / NEMA24, 1.8 step angle 86 mm / NEMA34, 1.8 step angle

QSH QSH QSH QSH QSH

89 90 91 92 93

QM o t B LDC m otors 4208 5704

42 mm / NEMA17, 8 poles 57 mm diameter, 4 poles

QBL QBL

94 95

www.trinamic.com for detailed information and datasheets

88

QMOT STE P P E R M O T O R S

M O T ORS

Q SH

2818

1 0 mm

28 mm / NEMA11 1 . 8 s t ep a n g le h i gh t o rq u e h y br i d st e p p e r m o t o r

M A IN CH A R AC T ER IS T IC S
IN F O

These two phase hybrid stepper motors are optimized for microstepping and give a good fit to the TRINAMIC family of motor controllers and drivers. They can be used in very space critical applications and allow high RPM due to their low back EMF. They are also used in the 28mm PANdrive mechatronics familiy.

NEMA 11 mounting configuration flange max. 28 mm * 28 mm 5 mm axis diameter, 20 mm length, D-Cut step angle: 1.8 optimized for microstep operation optimum fit for TMC222 / TMC236 / TMC246 based driver circuits 4 wire connection neodymium magnets for maximum torque CE approved RoHS compliant

SPECIFICATI O N S

UNIT

-32-07-0 06

-5 1-07-012

Rated phase current Ph. resistance at 20C Ph. inductance (typ.) Holding torque (typ.) Detent torque Rotor inertia Weight (mass) Motor length Related PAN-drive

0.67 5.6

0.67 9.2 7.2 12

mH Ncm Ncm gcm2 kg mm Type

3.4 6

9 0.11 32.0 PD1-...-42

18 0.20 51.0 PD3-...-42

ORDER CODE

D E S C RI P T I O N

QSH2818-32-07-006 QSH2818-51-07-012

QMot Steppermotor 28 mm, 0.67A, 0.06 Nm QMot Steppermotor 28 mm, 0.67A, 0.12 Nm

www.trinamic.com for detailed information and datasheets

89

QMOT STE P P E R M O T O R S

M O T ORS

Q SH

4218

1 0 mm

42 mm / NEMA17 1 . 8 s t ep a n g le h i gh t o rq u e h y br i d st e p p e r m o t o r

M A IN CH A R AC T ER IS T IC S
IN F O

These two phase hybrid stepper motors are optimized for microstepping and give a good fit to the TRINAMIC family of motor controllers and drivers. They are also used in the 42 mm PANdrive mechatronics family.

NEMA 17 mounting configuration flange max. 42.2 mm * 42.2 mm 5 mm axis diameter, 20 mm length Step angle: 1.8 optimized for microstep operation optimum fit for TMC236 / TMC246 based driver circuits up to 40V operating voltage 4 wire connection neodymium magnets for maximum torque RoHS compliant

SPECIFICATI O N S

UNIT

-35-10 -027

-41-10-035

-51 -10-049

Rated phase current Ph. resistance at 20C Ph. inductance (typ.) Holding torque (typ.) Detent torque Rotor inertia Weight (mass) Motor length Related PAN-drive

1.0 2.95

1.0 2.86 6.74 35 1.6 66 0.30 39 PD2-...-42

1.0 3.00 5.5 49 2.5 90 0.38 49 PD3-...-42

mH Ncm Ncm gcm2 kg mm Type

4.45 27 1.6 45 0.23 34.5 PD1-...-42

ORDER CODE

D E S C RI P T I O N

QSH4218-35-10-027 QSH4218-41-10-035 QSH4218-51-10-049

QMot Steppermotor 42 mm, 1A, 0.27 Nm QMot Steppermotor 42 mm, 1A, 0.35 Nm QMot Steppermotor 42 mm, 1A, 0.49 Nm

www.trinamic.com for detailed information and datasheets

90

QMOT STE P P E R M O T O R S

M O T ORS

Q SH

5718

1 0 mm

57 mm / NEMA23 1 . 8 s t ep a n g le h i gh t o rq u e h y br i d st e p p e r m o t o r

M A IN CH A R AC T ER IS T IC S
IN F O

These two phase hybrid stepper motors are optimized for microstepping and give a good fit to the TRINAMIC family of motor controllers and drivers. They are also used in the 57 mm PANdrive mechatronics family.

NEMA 23 mounting configuration flange max. 57.2 mm * 57.2 mm 6.35 mm axis diameter, 20.6 mm length step angle: 1.8 optimized for microstep operation optimum fit for TMC239 / TMC249 based driver circuits up to 84V operating voltage 4 wire connection neodymium magnets for maximum torque CE approved RoHS compliant

SPECIFICATI O N S

UNIT

-41-30 -047

-55-30-098

-79 -30-163

Rated phase current Ph. resistance at 20C Ph. inductance (typ.) Holding torque (typ.) Detent torque Rotor inertia Weight (mass) Motor length Related PAN-drive

3.0 0.8

3.0 0.8 2.1 98 3.0 209 0.70 55.0 PD2-...-57

3.0 0.8 3.2 163 3.0 335 1.00 78.5 PD3-...-57

mH Ncm Ncm gcm2 kg mm Type

1.5 47 2.1 77 0.50 41.0 PD1-...-57

ORDER CODE

D E S C RI P T I O N

QSH5718-41-30-047 QSH5718-55-30-098 QSH5718-79-30-163

QMot Steppermotor 57 mm, 3.0A, 0.47 Nm QMot Steppermotor 57 mm, 3.0A, 0.98 Nm QMot Steppermotor 57 mm, 3.0A, 1.63 Nm

www.trinamic.com for detailed information and datasheets

91

QMOT STE P P E R M O T O R S

M O T ORS

Q SH

6018

1 0 mm

60 mm / NEMA24 1 . 8 s t ep a n g le h i gh t o rq u e h y br i d st e p p e r m o t o r

M A IN CH A R AC T ER IS T IC S
IN F O

These two phase hybrid stepper motors are optimized for microstepping and give a good fit to the TRINAMIC family of motor controllers and drivers.

NEMA 23 mounting configuration flange max. 60.5 mm * 60.5 mm 8 mm axis diameter, 25 mm length, D-Cut step angle: 1.8 optimized for microstep operation optimum fit for TMC239 / TMC249 base driver circuits up to 75V operating voltage 4 wire connection neodymium magnets for maximum torque CE approved RoHS compliant

SPECIFICATI O N S

UNIT

-45-28- 110

-56-28-1 65

-65-2 8-210

-86-28 -310

Rated phase current Ph. resistance at 20C Ph. inductance (typ.) Holding torque (typ.) Rotor inertia Weight (mass) Motor length

2.8 0.75

2.8 0.9 3.6 165 400 0.77 56.0

2.8 1.2 4.6 210 570 1.20 65.0

2.8 1.5 6.8 310 840 1.40 86.0

mH Ncm gcm2 kg mm

2 110 275 0.6 45.0

ORDER CODE

D E S C RI P T I O N

QSH6018-45-28-110 QSH6018-56-28-165 QSH6018-65-28-210 QSH6018-86-28-310

QMot Steppermotor 60 mm, 2.8A, 1.10 Nm QMot Steppermotor 60 mm, 2.8A, 1.65 Nm QMot Steppermotor 60 mm, 2.8A, 2.10 Nm QMot Steppermotor 60 mm, 2.8A, 3.10 Nm

www.trinamic.com for detailed information and datasheets

92

QMOT STE P P E R M O T O R S

M O T ORS

Q SH

8618

10 mm

86 mm / NEMA34 1 . 8 s t ep a n g le h i gh t o rq u e h y br i d st e p p e r m o t o r

M A IN CH A R AC T ER IS T IC S
IN F O

These two phase hybrid stepper motors are optimized for microstepping and give a good fit to the TRINAMIC family of motor controllers and drivers.

NEMA 34 mounting configuration flange max. 85.85 mm * 85.85 mm step angle: 1.8 optimized for microstep operation optimum fit for TMCM-078 driver module insulation class: B max. radial / axial force 220N / 60N neodymium magnets for maximum torque CE approved RoHS compliant

SPECIFICATI O N S

UNIT

-65-59- 340

-80-55-4 60

-118- 60-870

-156-6 2-128 0

Number of leads Wiring Rated phase current Ph. resistance at 20C Ph. inductance (typ.) Holding torque (typ.) Max. operating voltage Axis diameter Axis length Rotor inertia Weight (mass) Motor length

8 SER PAR 5.9 0.28 1.7 340

3.0 1.14

5.5 0.42 3.5 460 140 12.7 (D-cut) 31.75 1400 2.3 80.0

6.0 0.45 5.1 870 140 12.7 (notch) 31.75 2700 3.8 118.0

6.2 0.75 9 1280 160 15.875(notch) 31.75 4000 5.4 156.0

mH Ncm V mm mm gcm2 kg mm

6.8 340 100 12 31.75 1000 1.7 65.0

ORDER CODE

D E S C RI P T I O N

QSH8618-65-59-340 QSH8618-80-55-460 QSH8618-118-60-870 QSH8618-156-62-1280

QMot Steppermotor 86 mm, 3.0A (SER) / 5.9A (PAR), 3.40 Nm QMot Steppermotor 86 mm, 5.5A, 4.60 Nm QMot Steppermotor 86 mm, 6.0A, 8.70 Nm QMot Steppermotor 86 mm, 6.2A, 12.80 Nm

www.trinamic.com for detailed information and datasheets

93

QMOT BLD C M O T O R S

M O T ORS

QBL

4208

42 mm 8 po l e B L DC m o to r
1 0 mm

M A IN CH A R AC T ER IS T IC S
IN F O

These BLDC motors give a good fit to the TRINAMIC family of medium and high current BLDC motor modules.

No. of poles: 8 No. of phases: 3 nominal 4000 RPM at rated torque stepper compatible 42 mm flange 5 mm axis diameter, 20 mm length typical 24V operating voltage up to 48V possible integrated hall sensors CE approved RoHS compliant

SPECIFICATI O N S

UNIT

-41-04- 006

-61-04-0 13

-81-0 4-019

-100-0 4-025

Rated current (typ.) Line resistance Line inductance Rated torque (typ.) Max. peak torque Max. peak current Torque constant Weight (mass) Motor length Related PAN-drive

1.8 1.8

3.5 0.72 1.2 0.125 0.38 10.6 0.036 0.45 61 PD2-...-42

5.2 0.55 0.8 0.185 0.56 15.5 0.036 0.65 81 PD3-...-42

6.9 0.28 0.54 0.25 0.75 20 0.036 0.80 100 PD4-...-42

mH Nm Nm A Nm/A kg mm Type

2.6 0.0625 0.19 5.4 0.035 0.30 41 PD1-...-42

ORDER CODE

D E S C RI P T I O N

QBL4208-41-04-006 QBL4208-61-04-013 QBL4208-81-04-019 QBL4208-100-04-025

QMot BLDC motor 42 mm, 4000RPM, 0.06Nm QMot BLDC motor 42 mm, 4000RPM, 0.13Nm QMot BLDC motor 42 mm, 4000RPM, 0.19Nm QMot BLDC motor 42 mm, 4000RPM, 0.25Nm

www.trinamic.com for detailed information and datasheets

94

QMOT BLD C M O T O R S

M O T ORS

QBL

5704

57 mm 4 pole BLDC motor

1 0 mm

M A IN CH A R AC T ER IS T IC S
IN F O

These BLDC motors give a good fit to the TRINAMIC family of high current BLDC motor modules. They are also used in the PANdrive mechatronics family.

No. of poles: 4 No. of phases: 3 nominal 4000 RPM at rated torque round flange max. 57 mm 8 mm shaft diameter, 25 mm length 2nd shaft for encoder mounting typical 36V operating voltage, 24V or 48V possible integrated hall sensors CE approved RoHS compliant

SPECIFICATI O N S

UNIT

-94-04-3 2

-1 16-04-42

Rated current (typ.) Line resistance at 20C Line inductance (typ.) Rated torque (typ.) Max. peak torque Max. peak current Torque constant Weight (mass) Motor length Related PAN-drive

5 0.45

6.6 0.35 1 0.42 1.30 20.5 0.063 1.40 116.0 PD5-...-57

mH Nm Nm A Nm/A kg mm Type

1.4 0.32 0.98 16.5 0.063 1.20 94.0 PD4-...-57

ORDER CODE

D E S C RI P T I O N

QBL5704-94-04-032 QBL5704-116-04-042

QMot BLDC motor 57 mm, 4000RPM, 0.32Nm QMot BLDC motor 57 mm, 4000RPM, 0.42Nm

www.trinamic.com for detailed information and datasheets

95

T R I N A M IC Motion Control GmbH & Co. KG Sternstrasse 67 20357 Hamburg Germany

TEL FAX WEB

+49 (0)40 514 806 0 +49 (0)40 514 806 60 www.trinamic.com