Electronics Final Year Project
Electronics Final Year Project
Although the appearance and capabilities of robots vary vastly, all robots share the features
of a mechanical, movable structure under some form of control. The control of robot involves three
distinct phases: perception, processing and action, generally, the preceptor are sensors mounted on
the robot, processing is done by the on board microcontroller or processor ,and the task (action) is
performed using motors with some other actuators.
PROJECT OVERVIEW
In this project, the robot is controlled by the mobile phone that makes a call to the
mobile phone attached to the robot .In the course of a call, if any button is pressed; a tone
corresponding to the button pressed is heared at the other end of the call. This tone is called ‘dual
tone-multiple-frequency’ (DTMF) tone .The robot perceives the DTMF tone with the help of the
phone stacked in the robot.
The received tone is processed by the ATmega16 microcontroller with the help of
DTMF decoder MT8870.The decoder decodes the DTMF tone into its equivalent binary digit and this
binary number is sent to the microcontroller. The microcontroller is programmed to take a decision
for any given input and outputs its decision to motor drivers in order to drive the motor for forward or
backward motion or a turn.
The mobile that makes a call to the mobile stacked in the robot as a remote. So this
simple robotic project does not require the construction of receiver and transmitter units.
DTMF signaling is used for telephone signaling over the line in voice-frequency
band to the call switching center. The version of DTMF used for telephone tone dialing is known as
‘Touch Tone’.
DTMF assigns a specific frequency (consisting of two separate tones) to each key
so that it can easily be identified by the electronics circuit. The signal generated by the DTMF
encoder is a direct algebraic summation, in real time, of the amplitude of two sine (cosine) waves of
different frequency, i.e., pressing ‘5’ will send a tone made by adding 1336Hz and 770Hz to the other
end of end of the line .The tones and assignment in a DTMF system are shown in table I.
CIRCUIT DESCRIPTION:
Fig.1 shows the block diagram of the microcontroller-based mobile phone-
operated land rover. The important components of this rover are a DTMF decoder, microcontroller
and motor driver.
An MT8870 series DTMF decoder is used here. All types of the MT8870 series use
digital counting techniques to detect and decode all the 16DTMF tone pairs into 4-bit code output.
The built in dial tone rejection circuit eliminates the need for pre-filtering. When the input signal given
at pin 2(IN-) in single-ended input configuration is recognised to be effective, the correct 4-bit
decode signal of the DTMF tone is transferred to Q1 (PIN11) through Q4 (PIN14) outputs.
Table II shows the DTMF data output table of MT8870.Q1through Q4 output of the
DTMF decoder (IC1) are connected to port pins PA0 through PA3 of ATmega16 microcontroller (IC2)
after inversion by N1 through N4,respectively.
SOFTWARE DESCRIPTION:
Software is written in ‘C’language and compiled using code vision AVR ‘c’compilerT
The source program is converted into hex code by the compiler .Burn this hex co0de into
ATmega16AVR microcontroller.
The source program is well commented and easy to understand .First include the
register name defined specifically for ATmega16 and also declare the variable .Set port A as input
and port D as output. The program will run forever by using ‘while’loop read port A and test the
received input using ‘switch’ statement. The corresponding data will output at port D after testing of
the received data.
WORKING:
In order to control the robot, you need to make a call to the cell phone attached to
the robot (through head phone) from any phone, which sends DTMF tunes on pressing the numeric
buttons. The cell phone in the robot is kept in ‘auto answer’mode.So after a ring, the cellphone
accepts the call.
Now you may press any button on your mobile to perform action as listed in the
table III.The DTMF tones thus produced are received by the cellophane in the robot .These tones
are fed to the circuit by the head set of cellphone.The MT8870 decodes the received tone and sends
the equivalent binary number to the microcontroller .According to the program in the microcontroller,
the robot start moving.
When you press key ‘2’ (in binary 00000010) on your mobile phone, the
microcontroller output’10001001’binary equivalent. Port pins PD0,PD3 and PD7 are high .The high
output at PD0 of the microcontroller drives the motor driver(L293D).Port pins PD0 and PD3 drive the
motor M1 and M2 in forward direction(as per table III).
Similarly, motor M1 and M2 move for left turn, right turn, backward motion and stop condition as per
table III.
CONSTRUCTION:
When constructing any robot, one major mechanical constraint is the
number of motor being used. You can have either two wheel or four wheel drive .Though four wheel
drive is more complex than two wheel drive, it provide more torque and better control. Two-wheel
drive, on the other hand very easy to construct.
Top view of a four-wheel-driven land rover is shown in fig 3.The chassis used in this
model is a 10*18cm^2 sheet made up of parax .Motor are fixed to the bottom of this sheet and the
circuit is affixed firmly on the top of the sheet. Cellophane is mounted on the sheet as shown in the
picture.
In the four-wheel drive system the two motor on a side are controlled in parallel. So
a single motor driver IC can drive the rover. For this robot, beads affixed with glue act as support
wheels.
FURTHER APPLICATION:
The land rover can be further improved to serve specific purpose .It require four
controls to roam around .The remaining eight controls can be configured to serve other purposes,
with some modification in the source program of the microcontroller.
ROBOT.C
#include<reg51.h>
Void main (void)
{