Fundamentals of Multimedia, Chapter 15

Chapter 15
Computer and Multimedia Networks

15.1 Basics of Computer and Multimedia Networks 15.2 Multiplexing Technologies 15.3 LAN and WAN 15.4 Access Networks 15.5 Common Peripheral Interfaces 15.6 Further Exploration

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

15.1 Basics of Computer and Multimedia Networks

Computer networks are essential to modern computing. Multimedia networks share all major issues and technologies of computer networks. The ever-growing needs for various multimedia communications have made networks one of the most active areas for research and development. Various high-speed networks are becoming a central part of most contemporary multimedia systems.

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

OSI Network Layers

OSI Reference Model has the following network layers: 1. Physical Layer: Denes electrical and mechanical properties of the physical interface, and species the functions and procedural sequences performed by circuits of the physical interface. 2. Data Link Layer: Species the ways to establish, maintain and terminate a link, e.g., transmission and synchronization of data frames, error detection and correction, and access protocol to the Physical layer. 3. Network Layer: Denes the routing of data from one end to the other across the network. Provides services such as addressing, internetworking, error handling, congestion control, and sequencing of packets. 3
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

OSI Network Layers (Contd)

4. Transport Layer: Provides end-to-end communication between end systems that support end-user applications or services. Supports either connection-oriented or connectionless protocols. Provides error recovery and ow control. 5. Session Layer: Coordinates interaction between user applications on dierent hosts, manages sessions (connections), e.g., completion of long le transfers. 6. Presentation Layer: Deals with the syntax of transmitted data, e.g., conversion of dierent data formats and codes due to dierent conventions, compression or encryption. 7. Application Layer: Supports various application programs and protocols, e.g., FTP, Telnet, HTTP, SNMP, SMTP/MIME, etc. 4
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

TCP/IP Protocols
OSI Application Presentation Session Transport Network Data link Physical Transport TCP (connection-oriented) UDP (connectionless) IPv4, IPv6, RSVP X.25, Ethernet, Token ring, FDDI, PPP/SLIP, etc. 10/100Base-T, 1000Base-T, Fibre Channel, etc. Application FTP, Telnet, SMTP/MIME HTTP, SNMP, etc. TCP / IP

Internet Network access (LLC and MAC) Physical

Fig. 15.1: Comparison of OSI and TCP/IP protocol architectures

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Transport Layer TCP and UDP

TCP (Transmission Control Protocol) Connection-oriented. Established for packet switched networks only no circuits and data still have to be packetized. Relies on the IP layer for delivering the message to the destination computer specied by its IP address. Provides message packetizing, error detection, retransmission, packet resequencing and multiplexing. Although reliable, the overhead of retransmission in TCP may be too high for many real-time multimedia applications such as streaming video UDP can be used instead. 6
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

UDP (User Datagram Protocol)

Connectionless: the message to be sent is a single Datagram. The only thing UDP provides is multiplexing and error detection through a Checksum. The source port number in UDP header is optional since there is no acknowledgment. Much faster than TCP, however it is unreliable: In most real-time multimedia applications (e.g., streaming video or audio), packets that arrive late are simply discarded. Flow control, and congestion avoidance, more realistically error concealment must be explored for acceptable Quality of Service (QoS). 7
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Network Layer IP (Internet Protocol)

Two basic services: packet addressing and packet fragmentation. Packet addressing: The IP protocol provides for a global addressing of computers across all interconnected networks. For an IP packet to be transmitted within LANs, either broadcast based on hubs or point-to-point transmission based on switch is used. For an IP packet to be transmitted across WANs, Gateways or routers are employed, which use routing tables to direct the messages according to destination IP addresses. 8
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Network Layer IP (Internet Protocol) (Contd)

The IP layer also has to: translate the destination IP address of incoming packets to the appropriate network address. identify for each destination IP the next best router IP through which the packet should travel based on routing table. Routers have to communicate with each other to determine the best route for groups of IPs. The communication is done using Internet Control Message Protocol (ICMP). IP is connectionless provides no end-to-end ow control, packets could be received out of order, and dropped or duplicated. 9
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Network Layer IP (Internet Protocol) (Contd)

Packet fragmentation: performed when a packet travels over a network that only accepts packets of a smaller size. IP packets are split into the required smaller size, sent over the network to the next hop, and reassembled and resequenced. IP versions: IPv4 (IP version 4): IP addresses are 32 bit numbers, usually specied using dotted decimal notation (e.g. 128.77.149.63) running out of new IP addresses soon (projected in year 2008). IPv6 (IP version 6): The next generation IP (IPng) adopts 128-bit addresses, allowing 2128 3.4 1038 addresses. 10
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

15.2 Multiplexing Technologies

Basics of Multiplexing 1. FDM (Frequency Division Multiplexing) Multiple channels are arranged according to their frequency: For FDM to work properly, analog signals must be modulated so that the signal occupies a bandwidth Bs centered at fc carrier frequency unique for each channel. The receiver uses a band-pass lter tuned for the particular channel-of-interest to capture the signal, and then uses a demodulator to decode it. Basic modulation techniques: Amplitude Modulation (AM), Frequency Modulation (FM), Phase Modulation (PM), and Quadrature Amplitude Modulation (QAM). 11
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

2. WDM (Wavelength Division Multiplexing): A variation of FDM for data transmission in optical bers: Light beams representing channels of dierent wavelengths are combined at the source, and split again at the receiver. The capacity of WDM is tremendous a huge number of channels can be multiplexed (aggregate bit-rate can be up to dozens of terabits per second). Two variations of WDM:
(a) DWDM (Dense WDM): employs densely spaced wavelengths so as to allow a larger number of channels than WDM (e.g., more than 32). (b) WWDM (Wideband WDM): allows the transmission of color lights with a wider range of wavelengths (e.g., 1310 to 1557 nm for long reach and 850 nm for short reach) to achieve a larger capacity than WDM.

12

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

3. TDM (Time Division Multiplexing) A technology for directly multiplexing digital data: If the source data is analog, it must rst be digitized and converted into PCM (Pulse Code Modulation). Multiplexing is performed along the time (t) dimension. Multiple buers are used for m (m > 1) channels. Two variations of TDM:
(a) Synchronous TDM: Each of the m buers is scanned in turn and treated equally. If, at a given time slot, some sources (accordingly buers) do not have data to transmit the slot is wasted. (b) Asynchronous TDM: Only assign k (k < m) time slots to scan the k buers that are likely to have data to send (based on statistics) has the potential of having a higher throughput given the same carrier data rate.

13

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

TDM Carrier Standards

T1 carrier is basically a Synchronous TDM of 24 voice channels (23 for data, and 1 for synchronization). Four T1 carriers are multiplexed to yield a T2. T3, T4 are further created in a similar fashion. ITU-T standard with Level 1 (E1): starting at 2.048 Mbps, in which each frame consists of 32 time slots (30 for data, and 2 for framing and synchronization).

14

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Table 15.1 Comparison of TDM Carrier Standards Format Num of channels T1 T2 T3 T4 24 96 672 4032 Data Rate (Mbps) 1.544 6.312 44.736 274.176 E1 E2 E3 E4 E5 Format Num of channels 32 128 512 2048 8192 Data Rate (Mbps) 2.048 8.448 34.368 139.264 565.148

15

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

ISDN (Integrated Services Digital Network)

In 1980s, the ITU-T started to develop ISDN (Integrated Services Digital Network) to meet the needs of various digital services. By default, ISDN refers to Narrowband ISDN. The ITUT has developed Broadband ISDN (B-ISDN). Its default switching technique is ATM (Asynchronous Transfer Mode). ISDN dened several types of full-duplex channels:
B (Bearer) channel: 64 kbps each for data transmission. Mostly circuit-switched, also support Packet Switching. D (Delta) channel: 16 kbps or 64 kbps takes care of call set-up, call control (call forwarding, call waiting, etc.), and network maintenance.

16

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Main specications of ISDN

ISDN adopts the technology of Synchronous TDM (Time Division Multiplexing) in which the above channels are multiplexed. Two type of interfaces were available: Basic Rate Interface: Provides two B-channels and one D-channel (at 16 kbps). The total of 144 kbps (64 2 + 16) is multiplexed and transmitted over a 192 kbps link. Primary Rate Interface: Provides 23 B-channels and one D-channel (at 64 kbps) in North America and Japan (t in T1); 30 B-channels and two D-channels (at 64 kbps) in Europe (t in E1). 17

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

SONET (Synchronous Optical NETwork)

A standard initially developed by Bellcore for optical bers. It uses the technology of circuit switching.
SONET adopts the technology of Synchronous TDM (Time Division Multiplexing). An STS-1 (OC-1) frame consists of 810 TDM bytes. It is transmitted in 125 sec, i.e., 8,000 frames per second. Hence a data rate of 810 8 8, 000 = 51.84 Mbps for STS-1 (OC-1). All other STS-N (OC-N) signals are further multiplexing of STS-1 (OC-1) signals. For example, three STS-1 (OC-1) are multiplexed for each STS-3 (OC-3) at 155.52 Mbps.

ITU-T developed a similar standard to SONET SDH (Synchronous Digital Hierarchy).

18

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Table 15.2:
SONET Electrical-Level STS-1 STS-3 STS-9 STS-12 STS-18 STS-24 STS-36 STS-48 STS-96 STS-192

Equivalency of SONET and SDH

SONET SDH Equivalent STM-1 STM-3 STM-4 STM-6 STM-8 STM-12 STM-16 STM-32 STM-64 Line Rate (Mbps) 51.84 155.52 466.56 622.08 933.12 1244.16 1866.24 2488.32 4976.64 9953.28 Payload Rate (Mbps) 50.112 150.336 451.008 601.344 902.016 1202.688 1804.032 2405.376 4810.752 9621.504

Optical-Level OC-1 OC-3 OC-9 OC-12 OC-18 OC-24 OC-36 OC-48 OC-96 OC-192

Table 15.2 lists the SONET electrical and optical levels, and their SDH equivalents and data rates. 19
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

ADSL (Asymmetric Digital Subscriber Line)

Adopts a higher data rate downstream and lower data rate upstream, hence asymmetric. Makes use of existing telephone twisted-pair lines to transmit QAM (Quadrature Amplitude Modulated) digital signals. Bandwidth on ADSL lines: 1 MHz or higher. ADSL uses FDM to multiplex three channels:
(a) the high speed (1.5 to 9 Mbps) downstream channel at the high end of the spectrum. (b) a medium speed (16 to 640 kbps) duplex channel. (c) a POTS (Plain Old Telephone Service) channel at the low end (next to DC, 0-4 kHz) of the spectrum.

20

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

ADSL Distance Limitation

ADSL is known to have the following distance limitation when only using ordinary twisted-pair copper wires:
Table 15.3: Maximum Distance of ADSL Using Twisted-Pair Wire Data Rate Wire Size Distance 1.544 Mbps 1.544 Mbps 6.1 Mbps 6.1 Mbps 0.5 mm 0.4 mm 0.5 mm 0.4 mm 5.5 km 4.6 km 3.7 km 2.7 km

Key technology for ADSL: Discrete Multi-Tone (DMT).

For a better transmission in potentially noisy channels, the DMT modem sends test signals to all subchannels rst. It then calculates the SNRs to dynamically determine the amount of data to be sent in each subchannel.

21

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Table 15.4 History of Digital Subscriber Lines

Name V.32 or V.34 DSL HDSL Meaning Voice Band Modems Digital Subscriber Line High Data Rate Digital Subscriber Line SDSL Single Line Digital Subscriber Line ADSL Asymmetric Digital Subscriber Line VDSL Very high data rate Digital Subscriber Line Data Rate 1.2 to 56 kbps 160 kbps 1.544 Mbps or 2.048 Mbps 1.544 Mbps or 2.048 Mbps 1.5 to 9 Mbps 16 to 640 kbps 13 to 52 Mbps 1.5 to 2.3 Mbps Down Up Down Up Duplex Mode Duplex Duplex Duplex

Table 15.4 oers a brief history of various digital subscriber lines (xDSL). 22
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

15.3 LAN and WAN

LAN (Local Area Network) is restricted to a small geographical area, usually to a relatively small number of stations. WAN (Wide Area Network) refers to networks across cities and countries. MAN (Metropolitan Area Network) is sometimes also used to refer to the network between LAN and WAN.

23

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Local Area Networks (LANs)

In IEEE 802 Reference Model for LANs, the functionality of the Data Link layer is enhanced, and it has been divided into two sublayers: Medium Access Control (MAC) layer:
(a) Assemble or disassemble frames upon transmission or reception. (b) perform addressing and error correction. (c) Access control to shared physical medium.

Logical Link Control (LLC) layer:

(a) Flow and error control. (b) MAC-layer addressing. (c) Interface to higher layers. LLC is above MAC in the hierarchy.

24

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Ethernet
Ethernet: A packet-switched bus network, the most popular LAN to date. Message Addressing: An Ethernet address of the recipient is attached to the message, which is sent to everyone on the bus. Only the designated station will receive the message, while others will ignore it. CSMA/CD (Carrier Sense Multiple Access with Collision Detection) solves the problem of medium access control: Multiple stations could be waiting and then sending their messages at the same time, causing a collision. To avoid collision, the station that wishes to send a message must listen to the network (Carrier Sense) and wait until there is no trac on the network. 25
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Token Ring
Token Ring: Stations are connected in a ring topology, as the name suggests. Collision resolve scheme: A small frame, called a token, circulates on the ring while it is idle. To transmit, a source station S must wait until the token passes by, and then seizes the token and converts it into a front end of its data frame, which will then travel on the ring and be received by the destination station. The data frame will continue travelling on the ring until it comes back to Station S . The token is then released by S and put back onto the ring. 26
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

FDDI (Fiber Distributed Data Interface)

A successor of the original Token Ring. Its Medium Access Control (MAC) is very similar to the MAC for Token Rings. Has a dual ring topology with its primary ring for data transmission and secondary ring for fault tolerance. Once a station captures a token, the station is granted a time period, and can send as many data frames as it can within the time period. The token will be released as soon as the frames are transmitted (early token release). Primarily used in LAN or MAN backbones, and supports both synchronous and asynchronous modes. 27
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Wide Area Networks (WANs)

Instead of broadcast, the following switching technologies are used in WAN: Circuit Switching: An end-to-end circuit must be established that is dedicated for the entire duration of the connection at a guaranteed bandwidth. Initially designed for voice communications, it can also be used for data transmission narrow-band ISDN. In order to cope with multi-users and variable data rates, it adopts FDM or Synchronous TDM multiplexing techniques. Inecient for general multimedia communications, especially for variable (sometimes bursty) data rates. 28
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Wide Area Networks (WANs) (Contd)

Packet Switching: used for almost all data networks in which data rates tend to be very much variable, and sometimes bursty. Data is broken into small packets, usually of 1,000 bytes or less in length. The header of each packet will carry necessary control information such as destination address, routing, etc. X.25 was the most commonly used protocol for Packet Switching. Two approaches are available to switch and route the packets: datagram and virtual circuits.

29

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Wide Area Networks (WANs) (Contd)

Frame Relay: A cheaper version of packet switching with minimal services, working at the data link control layer. Frame Relay made the following major changes to X.25: Reduction of error-checking: no more acknowledgement, no more hop-to-hop ow control and error control. Reduction of layers: the multiplexing and switching of virtual circuits are changed from Layer 3 in X.25 to Layer 2. Layer 3 of X.25 is eliminated. Frames have a length up to 1,600 bytes. When a bad frame is received, it will simply be discarded very high data rate: ranging from T1 (1.5 Mbps) to T3 (44.7 Mbps). 30
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Wide Area Networks (WANs) (Contd)

Cell Relay ATM (Asynchronous Transfer Mode): Small and xed-length (53 bytes) packets are adopted cells. As shown in Fig. 15.2, the small packet size is benecial in reducing latency in ATM networks. When the darkened packet arrives slightly behind another packet of a normal size (e.g,. 1 kB): (a) It must wait for the completion of the others transmission, hence serialization delay. (b) Much less waiting time is needed for the darkened cell to be sent. Signicantly increases the network throughput especially benecial for real-time multimedia applications. 31
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

(a)

(b)

Fig. 15.2: Latency: (a) Serialization delay in a normal packet switching network. (b) Lower latency in a cell network.

32

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Fixed data rate Circuit switching Cell relay (ATM) Complexity Frame relay Packet switching Variable data rate

Fig. 15.3: Comparison of Dierent Switching Techniques. Fig. 15.3 compares the four switching technologies in terms of their bit rate and complexity. It can be seen that Circuit Switching is the least complex and oers constant (xed) data rate, and Packet Switching is the opposite.

33

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

ATM Cell Structure

A xed format: 53 bytes, of which the rst 5 bytes are for the cell header, followed by 48 bytes of payload. The ATM Layer has two types of interfaces: UNI (UserNetwork Interface) is local, between a user and an ATM network, and NNI (Network-Network Interface) is between ATM switches.

34

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

The structure of an ATM UNI cell header:

GFC VPI VCI C PT L P HEC

16 5 bytes

24

32

40

GFC = General Flow Control VPI = Virtual Path Identifier VCI = Virtual Channel Identifier
GFC: General Flow Control VPI: Virtual Path Identier VCI: Virtual Channel Identier

PT

= Payload Type

CLP = Cell Loss Priority HEC = Header Error Check

PT: Payload Type CLP: Cell Loss Priority HEC: Header Error Check

Fig. 15.4: ATM UNI Cell header 35

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

ATM Layers and Sublayers

As Fig. 15.5 shows, AAL corresponds to the OSI Transport and part of the Network layers. It consists of two sublayers: CS and SAR: CS provides interface (convergence) to user applications and SAR is in charge of cell segmentation and reassembly. The ATM layer corresponds to parts of the OSI Network and Data Link layers. Its main functions are ow control, management of virtual circuit and path, and cell multiplexing and demultiplexing. Two sublayers of ATM Physical layer: TC and PMD. PMD corresponds to the OSI Physical layer, whereas TC does header error checking and packing/unpacking cells. 36
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

OSI

ATM

Transport Network

CS AAL SAR ATM

Data link Physical Physical

TC PMD

AAL = ATM Adaptation Layer CS TC = Convergence Sublayer = Transmission Convergence SAR = Segmentation and Reassembly PMD = Physical Medium Dependent

Fig. 15.5 Comparison of OSI and ATM Layers. 37

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

15.4 Access Networks

An access network connects end users to the core network. It is also known as the last mile. Beside ADSL, discussed earlier, some known options for access networks are: Hybrid Fiber-Coax (HFC) Cable Network Optical bers connect the core network with Optical Network Units (ONUs) in the neighborhood, each of which typically serves a few hundred homes. All end users are then served by a shared coaxial cable. A potential problem of HFC is the noise or interference on the shared coaxial cable. Privacy and security on the upstream channel are also a concern.

38

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Fiber To The Curb (FTTC) Optical bers connect the core network with ONUs at the curb. Each ONU is then connected to dozens of homes via twisted-pair copper or coaxial cable. A star topology is used at the ONUs, so the media to the end user are not shared a much improved access network over HFC. Fiber To The Home (FTTH) Optical bers connect the core network directly with a small group of homes, providing the highest bandwidth. Since most homes have only twisted pairs and/or coaxial cables, the implementation cost of FTTH will be high.

39

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Terrestrial Distribution uses VHF and UHF spectra (approximately 40800 MHz). Each channel occupies 8 MHz in Europe and 6 MHz in the U.S., and each transmission covers about 100 kilometers in diameter. The standard is known as Digital Video BroadcastingTerrestrial (DVB-T). Since the return channel (upstream) is not supported in terrestrial broadcasting, a separate POTS or N-ISDN link is recommended for upstream in interactive applications. Satellite Distribution uses the Gigahertz spectrum. Each satellite covers an area of several thousand kilometers. Its standard is Digital Video Broadcasting-Satellite (DVBS). Similar to DVB-T, POTS or N-ISDN is proposed as a means of supporting upstream data in DVB-S. 40
Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

Table 15.6: Speed of Common Peripheral Interfaces

Type Serial Port Standard parallel port USB ECP/EPP parallel port IDE SCSI-1 SCSI-2 (Fast SCSI, Fast narrow SCSI) Fast wide SCSI (Wide SCSI) Ultra SCSI (SCSI-3, Ultra narrow SCSI) EIDE Wide Ultra SCSI (Fast 20) Ultra2 SCSI IEEE 1394 (FireWire, i.LINK) USB 2 Wide Ultra2 SCSI (Fast 40) Ultra3 SCSI Ultra ATA 133 Wide Ultra3 SCSI (Ultra 160 SCSI, Fast 80) HIPPI Ultra 320 SCSI Fiber Channel Ultra 640 SCSI Data-rate 115 kbps 115 kB/s 1.5 MB/s 3 MB/s 3.3 - 16.7 MB/s 5 MB/s 10 MB/s 20 MB/s 20 MB/s 33 MB/s 40 MB/s 40 MB/s 1.5 - 50 MB/s 60 MB/s 80 MB/s 80 MB/s 133 MB/s 160 MB/s 100 - 200 MB/s 320 MB/s 100 - 400 MB/s 640 MB/s

41

Li & Drew c Prentice Hall 2003

Fundamentals of Multimedia, Chapter 15

15.6 Further Exploration

Text books: Computer Networks by A.S. Tanenbaum Data & Computer Communications by W. Stalling Web sites: ing: Link to Further Exploration for Chapter 15.. includ-

SONET FAQ, etc. xDSL introductions at DSL Forum website. Introductions and White Papers on ATM. FAQ and White Papers on 10 Gigabit Ethernet at the Alliance website. IEEE 802 standards. IETF RFCs: IPv6 (Internet Protocol, Version 6).

42

Li & Drew c Prentice Hall 2003