Web Site: www.ijaiem.org Email: [email protected], editorijaiem@gmail.

com Volume 2, Issue 4, April 2013 ISSN 2319 - 4847

Review wireless and global system for mobile communication System through wireless network
Mr. Sachin R. Dave1, Prof. Mr. Chetan. J. Shelke2
M.E (CSE) Scholar, 2Assistant Professor, Department of CSE P. R. Patil College of Engineering and Technology Amravati-444602, India.
1

ABSTRACT
The field of wireless and mobile communication has a remarkable history that spans over a century of technology innovations from Marconi's first transatlantic transmission in 1899 to the worldwide adoption of cellular mobile services by over four billion people today. Wireless has become one of the most pervasive core technology enablers for a diverse variety of computing and communications applications ranging from third-generation/fourth-generation (3G/4G) cellular devices, broadband access, indoor Wi-Fi networks, vehicle -to-vehicle (V2V) systems to embedded sensor and radio-frequency identification (RFID) applications. This has led to an accelerating pace of research and development in the wireless area with the promise of significant new breakthroughs over the next decade and beyond. This paper provides a perspective of some of the research frontiers of wireless and mobile communications, identifying early stage key technologies of strategic importance and the new applications that they will enable. Specific new radio technologies discussed include dynamic spectrum access (DSA), white space, cognitive software-defined radio (SDR), antenna beam steering and multiple-input-multiple-output (MIMO), 60-GHz transmission, and cooperative communications. Taken together, these approaches have the potential for dramatically increasing radio link speeds from current megabit per second rates to gigabit per second, while also improving radio system capacity and spectrum efficiency significantly. The paper also introduces a number of emerging wireless/mobile networking concepts including ad hoc and mesh, delay-tolerant routing, and mobile content caching, providing a discussion of the protocol capabilities needed to support each of these usage scenarios. In conclusion, the paper briefly discusses the impact of these wireless technologies and networking techniques on the design of emerging audiovisual and multimedia applications as they migrate to mobile- Internet platforms.

Keywords: BTS, BSC, MSC, GMSC

1. INTRODUCTION
The mobile communication began is 1897 and evolved remarkable since then wireless system have been dramatically fast in past ten year or so. The concept of mobile cellular communication was first developed by the bell laboratories in 1960 and 1970. The features growth of consumer based mobile and portable communication system will be depend on the allocation of radio frequency spectrum and the regulatory decision. Before 1935 the radio system used in automobile. Such as police vans and other municipal corporation vehicles were based on amplitude modulation (AM) but the AM system suffered from noise produced by the automobile ignition system. In 1935edwin Armstrong demonstrated the frequency modulation (FM) and then from late 1930. F.M was adopted as modulation technique for mobile communication system all over the world.

2. Information on GSM Architecture

A basic cellular system which consist of mobile stations base stations and a mobile switching center (MSC). The mobile switching center is sometimes called a mobile telephone switching office (MTSO). Each mobile communicates via radio with one of the base station and may be handed off to any number of base stations throughout the duration of a call. The mobile station contains a transceiver an antenna and control circuitry, and may be mounted in a vehicle or used as a portable hand held unit. The base station consist of several transmitters and receivers which simultaneously handle full duplex communications and generally have towers which support several transmitting and receiving antennas. The base station serves as a bridge between all mobile users in the cell and connect the simultaneous mobile calls via telephone lines or microwave links to the MSC. The MSC coordinates the activities of all of the base stations and connects the entire cellular system to the PSTN. A typical MSC handles 100,000 cellular subscriber and 5,000 simultaneous conversions at a time, and accommodates all billing and system maintenance functions as well. In large cities several MSC are used by a single carrier.

Volume 2, Issue 4, April 2013

Page 185

Web Site: www.ijaiem.org Email: [email protected], [email protected] Volume 2, Issue 4, April 2013 ISSN 2319 - 4847
2.1 Local Call for Mobile to Mobile

Figure 1 Local call for mobile to mobile 2.2 STD Call for Mobile to Mobile

Figure 2 STD call for mobile to mobile

3. Base Transceiver Station (BTS)

A base transceiver station (BTS) or cell site is a piece of equipment that facilitates wireless communication between user equipment (UE) and a network. UEs are devices like mobile phones (handsets), WLL phones, computers with wireless internet connectivity, Wi-Fi and Wi-MAX gadgets etc. The network can be that of any of the wireless communication technologies like GSM, CDMA, WLL, WAN, Wi-Fi, WI-MAX etc. BTS is also referred to as the radio base station (RBS), node B (in 3G Networks) or, simply, the base station (BS). For discussion of the LTE standard the abbreviation eNB for evolved node B is widely used. Though the term BTS can be applicable to any of the wireless communication standards, it is generally and commonly associated with mobile communication technologies like GSM and CDMA. In this regard, a BTS forms part of the base station subsystem (BSS) developments for system management. It may also have equipment for encrypting and decrypting communications, spectrum filtering tools (band pass filters) etc. antennas may also be considered as components of BTS in general sense as they facilitate the functioning of BTS. Typically a BTS will have several transceivers (TRXs) which allow it to serve several different frequencies and different sectors of the cell (in the case of sectaries base stations). A BTS is controlled by a parent base station controller via the base station control function (BCF). The BCF is implemented as a discrete unit or even incorporated in a TRX in compact base stations. The BCF provides an operations and maintenance (O&M) connection to the network management system (NMS), and manages operational states of each TRX, as well as software handling and alarm collection. The basic structure and functions of the BTS remains the same regardless of the wireless technologies.

Volume 2, Issue 4, April 2013

Page 186

Web Site: www.ijaiem.org Email: [email protected], [email protected] Volume 2, Issue 4, April 2013 ISSN 2319 - 4847
The BTS contain actual radio component i.e. transmitter and receivers and are distributed over entire service area Base transceivers Station must be located in relatively large numbers at offices, roof spaces, Cellars etc. Equipment must therefore be compact robust and capable of full remote control operation. The control functions are carried out by BCS and Transceiver function by the BTS contains all the radio frequency Transmit / receive equipment. Micro BTS are applicable for indoor or outdoor usage with a flexible and redundant configuration to include the following: The maximum output power per carrier measured at the antenna connector after all stages of combining. Connection to the standard external antenna with optional support for internal diversity antennas. BTS also does the functions related channel coding/decoding , Interleaving, encryption, frame building, modulation/ demodulation, RF Transceiver, antenna diversity, law-noise amplification etc. 3.1 A BTS in general has the following parts: 1. Transceiver (TRX) Quite widely referred to as the driver receiver (DRX). DRX are either in the form of single (sTRU), double (dTRU) or a composite Double Radio Unit (DRU). It basically does transmission and reception of signals. Also does sending and reception of signals to/from higher network entities. 2. Power amplifier (PA) Amplifies the signal from DRX for transmission through antenna; may be integrated with DRX. 3. Combiner Combines feeds from several DRXs so that they could be sent out through a single antenna. Allows for a reduction in the number of antenna used. 4. Duplexer For separating sending and receiving signals to/from antenna. Does sending and receiving signals through the same antenna ports (cables to antenna). 5. Antenna This is the structure that lays underneath the BTS; it can be installed as it is or disguised in some way 6. Alarm extension system Collects working status alarms of various units in the BTS and extends them to operations and maintenance (O&M) monitoring stations. 7. Control function Control and manages the various units of BTS including any software. On-the-spot configurations, status changes, software upgrades, etc. are done through the control function. 8. Baseband receiver unit (BBxx). Frequency hopping, signal DSP, etc.

4. GSM Antenna
GSM, or Global System for Mobile Communication, is a system for transmitting mobile communication information. GSM uses a wide variety of antenna types. Indeed, as long as it is able to capture a GSM signal, almost any kind of antenna can potentially function as a GSM antenna. However, a few primary types of GSM antennas are in use today, and a review of these types is a good place to start in learning more about how GSM works. 4.1 TYPES OF GSM ANTENNAS: 1. GSM Antennas in General In general, GSM antennas must be small in size---small enough to be able to fit even inside a laptop bag. In addition, the antenna should have a gain of about 8 dBi. To operate at GSM antennas, the antenna must be able to receive both the standard and the extended GSM bands, 880 MHz (megahertz) to 960 MHz 2. Directional and Omnidirectional GSM antennas will be either directional or omnidirectional. Omnidirectional antennas, also known as helical antennas, can receive signals from any direction. Directional antennas usually have more gain, that is, more sensitivity to signal, than omnidirectional antennas. Directional antennas accomplish this greater sensitivity because they are able to focus their energy patterns onto a smaller area than omnidirectional antennas. However, to receive signal, directional antennas must be pointed in the specific direction from which the signal is emanating.

Volume 2, Issue 4, April 2013

Page 187

Web Site: www.ijaiem.org Email: [email protected], [email protected] Volume 2, Issue 4, April 2013 ISSN 2319 - 4847

3. Monopole Antennas Monopole antennas consist of a small pole placed upon a planar piece of metal or a series of wires radiated out from the pole. Monopole antennas are omnidirectional in nature and have equal gain in all directions. 4. Yagi-Uda Antennas Yagi-Uda antennas, more often referred to simply as Yagi antennas, are directional antennas made up of a dipole element, a reflector dish and one or more director elements. Yagi antennas are much more complicated in design than most other types of GSM antennas. 5. Multiband Antennas Multiband antennas can also be used to pick up GSM signals. They are able to pick up many sorts of different signals, including the GSM frequency, which is usually the 800 MHz or 1900 MHz bands. Multiband antennas can come in many different models. Tri-band antennas can be tuned to pick up three different bands, while duo-band antennas can pick up two different bands. 4.2 Parameter of GSM Antenna: GSM-02 Frequency Range(MHz)890-960/1710-1890 Bandwidth(MHz) 70/180 VSWR <=2Gain(dBi) 3 , Max Input power(W) 50 Input Impedance(Ohm) 50 Polarization Type Vertical Antenna Length(mm) 94 Connector Type SMA Straight/Right Angle connector Storage Temperature -30 Degree Celsius to +75 Degree Celsius Operating Temperature -30 Degree Celsius to+75 Degree Celsius

5. Base Station Controller (BSC)

The BSC controls one or several BTS and acts as a bridge between BTS and MSC. One or more BSC are linked to an MSC. There may be one or several BTSs. BSCV performs the radio processing functions such as management of Radio resources, radio channel management, local connection management etc. This also process information required for decision on hand over of calls to other radio interfaces. The BSC supports various BSC-BTS configurations and has a separate transcoding and rate adoption unit for speech coding and data Rate adaptation that can be either co-located with MSC or at separate Convenient side for optimum use of links. BSC also performs internal hand over, radio resource management and interface management.

6. Mobile Switching Center

The mobile switching center (MSC) is the primary service delivery node for GSM/CDMA, responsible for routing voice calls and SMS as well as other services (such as conference calls, FAX and circuit switched data).The MSC sets up and Releases the end-to-end connection, handles mobility and hand-over requirements during the call and takes care of charging and real time pre-paid account monitoring. 1. Location registration is to be handled by MSC in order to ensure inter working between the MS and the VLR. 2. Inter BSC handover and inter MSC handover shall be performed by the MSC. 3. To perform the exchange of signaling information with other entities like VLR of other MSC. 4. As SSP to perform the exchange of signaling information with SCP. 5. As inter working unit of providing in services to mobile scribers to interrogate EIR for getting Equipment information. 6. To handle inter working for grp-3 fax calls. 7. To support transfer of encryption parameters between VLR and BSS. 8. To provide special security functions like checking of IMeI. 9. To support the SMS. 10. To generate traffic and performance reports. 11. To generate call event records and trace records. 12. To support authentication of subscriber and equipment checking through operator control. 13. To support hot billing.

Volume 2, Issue 4, April 2013

Page 188

Web Site: www.ijaiem.org Email: [email protected], [email protected] Volume 2, Issue 4, April 2013 ISSN 2319 - 4847 7. Gateway MSC
The Gateway MSC (G-MSC) is the MSC that determines which visited MSC the subscriber who is being called is currently located at. It also interfaces with the PSTN. All mobile to mobile calls and PSTN to mobile calls are routed through a G-MSC. The term is only valid in the context of one call since any MSC may provide both the gateway function and the Visited MSC function, however, some manufacturers design dedicated high capacity MSCs which do not have any BSSs connected to them. These MSCs will then be the Gateway MSC for many of the calls they handle.

Figure 3 Gateway mobile switching Center 7.1 Home location register (HLR): The HLR database is used for storage and management of subscriptions. The home location register stores permanent data about subscribers, including a subscriber's service profile, location information, and activity status. 7.2 Visitor location register (VLR): The VLR database contains temporary information about subscribers that is needed by the mobile services switching center (MSC) in order to service visiting subscribers. When a mobile station roams into a new mobile services switching center (MSC) area, the visitor location register (VLR) connected to that MSC will request data about the mobile station from the HLR, reducing the need for interrogation of the home location register (HLR). 8. CONCLUSION This paper mainly introduces the development of mobile communication systems. In the first section, we briefly review the history of wireless communication and its applications. In the second section we focus on the wireless mobile communication and divide the development course of mobile communication into four generations. The concept of mobile wireless communication began in the 1920s. Some technologies had been developed such as frequency modulation (FM). Originally it was applied to the military communications and then introduced to the civil fields. However, it was the 1970s when mobile wireless communication became a real industry and the mobile telephones were sold as a real commodity. Up to now, mobile wireless communication has gone through two generations in the past twenty years. And currently it is heading for the third generation and beyond the third generation. In the following, the features of each generation are presented. REFERENCES [1] Text book Theodore S. Rupport, Wireless Communication (Principles and practices) 2nd Edition 2004. [2] Text book William C. y. Lee, Mobile Cellular Telecommunication MC Grow Hill 1995[8], [3] S.jain R. shah W. Brunette G. Borriello, and S. Roy, Exploiting mobility for energy efficient data collection wireless network,vol,pp,327- 339/2006 [4] Teleman wireless communication certificate course/notes. [5] www.trincoll.edu/depts/cpsc/Wireless communication/index.html [6] http://dmoz.org/Science/Math/Applications/Communication_Theory/ Mobile communication/Historical [7] Text book James F. Kurose Computer Networking (A Top-Down Approach Featuring the Internet 4th Edition, Addison Wesley 2008. [8] Telecomarticle.blogspot.in [9] En.wikipedia.org/wiki/Base_transceiver_station/Network_switching_subsystm [10] www.ehow.com/list_7279317_types_gsm-antnna.html

Volume 2, Issue 4, April 2013

Page 189

Web Site: www.ijaiem.org Email: [email protected], [email protected] Volume 2, Issue 4, April 2013 ISSN 2319 - 4847
[11] xylec.enccplaza.net/gsm-antenna114953-24849.html. [12] www.tutorialpoint.com/gsm/gsm_network_switching_ sys. AUTHORS Mr. Sachin R. Dave, Received Bachelors degree in Computer Science & Engineering from sant Gadge baba Amravati University in 2009 & pursuing Master degree from P.R. Patil college of Engineering Amravati-44402 India. Prof.Mr.Chetan J. shelke, Received Master degree in Computer Science & Engineering from sant Gadge baba Amravati University in 2011.Working as Assistant professor in Computer science & Engineering at P.R. Patil college of Engineering Amravati-44402 India

Volume 2, Issue 4, April 2013

Page 190