Scribd
Upload
75 views2 pages

Product Sensor Web-UK

The document describes a Kimax 2 sensor set that includes multiple sensors, displays, fittings, and accessories for measuring axle load on vehicles. The sensor set uses air pressure sensors to calculate axle load within 2% accuracy. It has adjustable alarms and can interface with other devices. The sensor set is modular and can be configured for different vehicle types and axle configurations.

Uploaded by

Ema Russi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
75 views2 pages

Product Sensor Web-UK

The document describes a Kimax 2 sensor set that includes multiple sensors, displays, fittings, and accessories for measuring axle load on vehicles. The sensor set uses air pressure sensors to calculate axle load within 2% accuracy. It has adjustable alarms and can interface with other devices. The sensor set is modular and can be configured for different vehicle types and axle configurations.

Uploaded by

Ema Russi
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Sensor Set includes:

Sensor

Kimax 2 sensor 3 x 2 sensors Part number 10113 1 x display unit, universal 6 x air pressure throttle dia. 6mm 6 x T-fitting dia. 8mm / 6mm / 8mm Kimax 2 sensor 3 sensors Part number 10116 3 x air pressure throttle dia. 6 mm 3 x T-fitting dia. 8mm / 6mm / 8mm

Axle load measurement Trailer version - direct on your chassis Kimax 2 sensor is a slave unit without display intended for communication with Kimax 2 radio or Kimax 2 universal through divice bus. The Kimax 2 On-Board Load Control is an electronic weighing system which can be used in all vehicles whose axles or axle groups are equipped within air suspension system. Due to the modular construction, the product is very flexible and can be
Tonne

Kimax 2 uses the linearity between air pressure and load of the single axles. By using two reference points for each axle (empty weight and weight at maximum load) and the currently measured air pressure, Kimax 2 calculates the current axle load with an accuracy of 2 % of the maximum load for each axle.
Kimax 2 12,0 10,0 8,0 6,0 4,0 2,0 0,0 Front Rear Lo - front Hi - front Lo - rear Hi - rear

individually adapted to most vehicle conditions.

Kimax 2 sensor has two seperately adjustable alarm levels Alarm 1 is indicated by a flashing diode for the individual axle on the connected Kimax 2 radio or Kimax 2 universal display unit. Alarm 2 which switches in an internal "relay" when the total weight for this vehicle is exceeded. The relay signal can be used as ON/OFF input for another unit, for example an FM 200 on-board computer or a thacograph.

1,00

2,00

3,00

4,00

5,00 Bar

6,00

7,00

8,00

9,00

Basic operation
Depending on load of the vehichle, the level valve maintain a constant height of the chassis above ground surface by regulating the pressure in the pods.

Basic semitrailer installation with best accuracy


2 air sensors on each axle offer you the best accuracy, even you operate your lift-axle. The influence of inclination or slightly uphill/downhill standing is partly compensated in this configuration, as well as weighing accuracy is unaffected on the distribution of goods loaded on the vehicle.

Basic trailer installation with best accuracy


2 air sensors on each axle offer you the best accuracy, even you operate your lift-axle. The influence of inclination or slightly uphill/downhill standing is partly compensated in this configuration, as well as weighing accuracy is unaffected on the distribution of goods loaded on the vehicle.

Air circuits and sensors On all vehicles you get best accuracy with two independent air inlets for each axle, one for each pneumatic circuit (right and left) per axle or axle group, Kimax 2 calculates the current axle load on each axle from two reference values LO and HI. When less accuracy is enough for you, one air inlet on each axle or axle group is available too. Using a single SG sensor on a front axle typically offer you the same. accuracy compared with an front axle with air suspension. For heavy load vehicles hydraulic sensors are available too.

Technical Specifications
Supply voltage Current consumption Alarm 2 Measuring accuracy Air connection Maximum pressure Operating pressure Device bus 10 ... 30 Volt direct current max. 90 mA output open collector NPN max. 0.2 A/ 50 VDC 2 % of maximum load at 0 C - +50 C Quick release connection, 6 mm hose 15.5 bar (225 psi ) range 0 to 10.5 bar(0 to 150 psi ) Power line communication

Operating temperature -25 C...+70 C

Optional versions: Kimax 2 is exactly as flexible as your vehicle: Do you have a tractor equipped with steel springs on front axle and air suspension on rear axles combined with a lift axle? No problem! Do you have a truck with 2 front axles equipped with steel springs and two rear axles divided in left hand and right hand air circuits? No problem! Do you want to couple a trailer or semitrailer on the above vehicles, we do it! Do you want to couple a low bed trailer equipped with hydraulic suspension on a tractor equipped with air suspension? No problem! Do you want to swap from one trailer to another trailer, you just do it! Individual calibration values are stored in the Kimax unit on each vehicle.

Storage temperature Dimensions Weight Approval

-40 C...+70 C 180 x 135 x 60 mm approx. 750 g CE and e1

Kimax 1 and Kimax 2 are a series of high quality well proven on-board scales for use on trucks, buses and loading equipment. For detailed product selection guide please go to Kimax.com. Kimax 1 and Kimax 2 are registered trademarks owned by Sense-Tech Weighing Systems. Sense -Tech Weighing Systems are used all over the world. From the hectic harbours of Amsterdam to the dusty outback of Australia. And everywhere in between.

Associated units Kimax 2 sensor is a slave unit which is able to communicate with both Kimax 2 radio and Kimax 2 universal

Weighing Systems

Sense-Tech Weighing Systems ApS Bygade 43 A DK-7173 Vonge Tel. +45 7670 3001 Fax. +45 7670 3002, Email: [email protected] www.sense-tech.com

You might also like