Models PT-10 and PT-20

www.vishay.com

Vishay Dale

Through-Hole Transformers Pulse, Trigger Type

FEATURES
Choice of printed configurations circuit or bobbin-type

Designed to transfer high amplitude or long duration pulses without saturation Designed for low-cost trigger source isolation in half and full wave SCR power control circuits, including motor speed controls, heater controls and incandescent lighting controls Compliant to RoHS Directive 2002/95/EC

STANDARD ELECTRICAL SPECIFICATIONS

DASH NUMBER 101 (1) 102 (1) 103 (1) 104 105 106 (1) 107 108 109 110 111 113 114 115 (1) 116 (1) 117 (1) 118 119 120 (1) 121
(1)

TURNS RATIO 1:1 10 % 1:1 10 % 1:1 10 % 1:1 10 % 1:1 10 % 1:1:1 10 % 1:1:1 10 % 1:1:1 10 % 1:1:1 10 % 1:1:1 10 % 2:1 10 % 2:1 10 % 2:1 10 % 2:1 10 % 2:1:1 10 % 2:1:1 10 % 2:1:1 10 % 2:1:1 10 % 2:1:1 10 % 5:1 10 % 5:1:1 10 %

FIGURE 1/3 1/3 1/3 1/3 1/3 2/4 2/4 2/4 2/4 2/4 1/3 1/3 1/3 1/3 2/4 2/4 2/4 2/4 2/4 1/3 2/4

PRIMARY IND. MIN. (H) 200 500 1000 2000 5000 200 500 1000 2000 (1) 5000 500 1000 2000 5000 200 500 1000 2000 5000 5000 5000

LEAKAGE IND. MAX. (H) 3 6 12 13 15 3 6 12 13 15 6 10 12 15 8 11 15 60 75 1500 1500

INTERWINDING CAPACITY MAX. (pF) 800 1500 2000 2800 3500 800 1500 2000 2800 3500 1000 1300 1800 2400 700 1000 1300 2000 2100 400 400

DCR MAX. () 1.5-1.5 4.5-4.5 8-8 12-12 18-18 2-2-2 6-6-6 10-10-10 15-15-15 27-27-27 4-2 10-2 10-5 18-10 4-2-2 6-2-2 5-2-2 10-5-5 20-10-10 19-3 20-4-4

UNIPOLAR ET (V-s) 570 912 1283 1853 2850 570 912 1283 1853 2850 912 1288 1881 2850 570 912 1311 1881 2850 2850 2850

112 (1)

Note (1) Standard items in PT-10 Model. Other dash numbers available on request. All dash numbers standard in PT-20 model

ELECTRICAL SPECIFICATIONS
Primary Inductance Values: From 200 H to 5000 H Turns Ratio: 1:1, 1:1:1, 2:1, 2:1:1 and 5:1 Temperature Range: - 10 C to + 70 C Dielectric Test at 60 Hz: 1600 VRMS (Windings to case) AC Line Voltage at 60 Hz: 240 VRMS maximum in test circuits shown

MATERIAL SPECIFICATIONS
Bobbin: Nylon Leads: Tinned, solderable PT-10 = Polyurethane insulated magnet wire for clip or bracket mounting PT-20 = Tinned copper 0.025 [0.635] sq. for printed circuit mounting Header: Thermoset plastic Covering: Thermoplastic

Revision: 06-Dec-11

Document Number: 34073 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Models PT-10 and PT-20

www.vishay.com

Vishay Dale

CIRCUIT DIAGRAMS
Load Load

Line

Line

Transformer Coupled Unijunction Transistor Triggering Circuit

Transformer Coupled Breakdown Diode Triggering Circuit

DIMENSIONS in inches (millimeters)

PT-10
0.593 0.062 [15.06 1.57] Dia. RED GRN. 0.010 [0.254] Dia., 4 Leads 0.828 0.062 [21.03 1.57] RED GRN.

PT-10
0.593 0.062 [15.06 1.57] Dia. NAT. GRN. RED 0.010 [0.254] Dia., 6 Leads 0.828 0.062 [21.03 1.57] NAT. GRN. RED

1 3

2 4 1.50 [38.10] Min. Typ.

5 3 1

6 4 2

1.50 [38.10] Min. Typ. RED 1 GRN. 3 NAT. 5

RED 1

GRN. 3

PRI.

SEC.

PRI.

SEC.

TER.

Figure 1

2 RED

4 GRN.

Figure 2
0.800 [20.32] Max. 0.250 [6.35] Min.

2 RED

4 GRN.

6 NAT.

PT-20
0.968 [24.59] Max. 0.775 [19.68] Max.

PT-20
0.968 [24.59] Max. 0.775 [19.68] Max. 0.250 [6.35] Min.

0.800 [20.32] Max.

2 0.600 [15.24] 1

4 0.600 [15.24] 3 0.300 [7.62] Ref. 0.250 [6.35] Ref. 1 3

2 5 1

4 6 3 0.300 [7.62] Ref. 0.250 [6.35] Ref.

0.500 [12.70]

0.025 [0.635]Sq. 4 Leads

0.500 [12.70]

0.025 [0.635]Sq 6 Leads 5

PRI.

SEC.

PRI.

SEC.

TER.

Figure 3

Figure 4

PART MARKING
- Vishay Dale - Model - Style - Dash number Revision: 06-Dec-11 Document Number: 34073 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Models PT-10 and PT-20

www.vishay.com

Vishay Dale

ORDERING INFORMATION
PT MODEL 10 STYLE 101 DASH NUMBER EB PACKAGE CODE e2 JEDEC LEAD (Pb)-FREE STANDARD

GLOBAL PART NUMBER

P T 0 1 STYLE 0 E B 1 0 1

MODEL

PACKAGE CODE

DASH NUMBER

Revision: 06-Dec-11

Document Number: 34073 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice

www.vishay.com

Vishay

Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishays knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customers responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customers technical experts. Product specifications do not expand or otherwise modify Vishays terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards.

Revision: 02-Oct-12

Document Number: 91000