Scribd
Upload
1K views

Determining Coefficient of Friction

The document describes an experiment to determine how mass affects the coefficient of kinetic friction. The experiment involved pulling masses of 400g, 700g, and 1000g across a table surface and measuring the frictional force with a spring scale. Contrary to the hypothesis that friction decreases with increasing mass, the results showed friction increased with mass. The largest 1000g mass had the highest coefficient of 0.248, while the smallest 400g mass had the lowest of 0.128. Sources of error were the uneven mass surfaces and imprecise spring scale. The experiment did not validate the initial hypothesis and could be improved with a more accurate force measuring tool.

Uploaded by

jahajaha_svensson609
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC or read online on Scribd
1K views

Determining Coefficient of Friction

The document describes an experiment to determine how mass affects the coefficient of kinetic friction. The experiment involved pulling masses of 400g, 700g, and 1000g across a table surface and measuring the frictional force with a spring scale. Contrary to the hypothesis that friction decreases with increasing mass, the results showed friction increased with mass. The largest 1000g mass had the highest coefficient of 0.248, while the smallest 400g mass had the lowest of 0.128. Sources of error were the uneven mass surfaces and imprecise spring scale. The experiment did not validate the initial hypothesis and could be improved with a more accurate force measuring tool.

Uploaded by

jahajaha_svensson609
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC or read online on Scribd
You are on page 1/ 5

Christina Svensson

Mr Wardle
SPH3U- 02
29.10.2008
02.11.2008

Determining coefficients of friction

1
Purpose:
Investigate the coefficient of kinetic friction for two materials and determine how mass
affect the coefficient of friction.

Question:
How does the mass of an object affect the coefficient of friction?

Hypothesis:
For an increase in the normal force, there will be a corresponding decrease in the
coefficient of friction.

Fg=m x g
Fg=Fn
Ff=M x Fn
∑ M= Ff / Fn

Design:
This investigation of factors (in this case mass) affecting the coefficient of friction, we
attached a certain mass to a spring scale (which measure force in Newtons) and pulled it
across a table. The masses being used was 400 g, 700 g and 1000 g.

Independent variables:
- Mass of object attached to the spring scale.
Dependent variables:
- Uneven surface
- Force of mass, N, shown on the spring scale.
Controlled variables:
-

Materials:
- Spring scale
- 3 x 200 g mass
- 1 x 100 g mass
- 1 x 1000 g mass

Procedure:
1. Obtained the masses needed for the experiment
2. Attached the 1st mass (2 x 200 g) to the spring and pulled it across the table.
Observe the spring and record data. Repeat procedure 3 times with the same mass.
3. Same procedure was repeated with 700 g and 1000 g. Record data.
4. Cleaned up lab area

2
Observations:
Refer to Table 1: Force of kinetic friction on selected masses. The data could be in error
because the surface of the mass being used was slightly uneven, and that would lead to
errors in calculations.

Analysis:
Refer to Table 3: Coefficient of kinetic friction. As the results clearly shows, my results
were wrong, and I have not proved my hypothesis. The smallest mass (400 g) had the
smallest coefficient; 0.128 ± 10.83, while the largest mass (1000 g) had the greatest;
0.248 ± 2.89%. This lab did not validate my hypothesis. As mentioned in my observation;
my results might have been in error because of the uneven surface of the mass used.

Evaluation:
This lab was not a good lab. It was supposed to prove my hypothesis, which it did not do.
My uncertainty for the 400 g mass is to large, and if I were to do it again, I would use a
more accurate toll for measuring the force of friction. My errors were also big; I used
cube-shaped masses, and they rolled around while pulling it over the table’s surface,
causing the measuring of force of friction to constantly change (“needle” jumped up and
down).

3
Appendix

Table 1: Force of kinetic friction on selected masses


Surface: Mass (g): Mass (N) Try 1 (N): Try 2 (N): Try 3 (N):

Table 400 4 0.4 0.5 0.5


Table 700 7 1.5 1.5 1.5
Table 1000 10 1.7 1.7 1.8

Table 2: Force of kinetic friction (average with uncertainties).


Mass: 400 g 700 g 1000 g

Average of tries: 0.5 N ± 10.83% 1.5 N ± 3.33% 1.7 N ± 2.89

Uncertainty: Try 1) 0.05 / 0.4 Try 1) 0.05 / 1.5 Try 1) 0.05 / 1.7
= 0.125 ~ 0.333 ~ 0.294
= 12.5% ~ 3.33% ~ 2.94%

Try 2) 0.05 / 0.5 Try 2) 0.05 / 1.5 Try 2) 0.05 / 1.7


= 0.1 ~ 0.333 ~ 0.294
= 10% ~ 3.33% ~ 2.94%

Try 3) 0.05 / 0.5 Try 3) 0.05 / 1.5 Try 3) 0.05 / 1.8


= 0.1 ~ 0.333 ~ 0.0278
= 10% ~ 3.33% ~ 2.78%

4
Table 3: Coefficient of kinetic friction
Mass (m): Normal Force (Fn) Force of Friction Coefficient of friction ( μ )
(Ff); data recorded
of spring scale
(average ±
uncertainties).
400 g Fn = F g Ff = 0.5 N ± 10.83% = F f / Fn
Fg = g x m = 0.5 N / 3.92 N
= 9.8 m/s2 x 0.4 kg = 0.128 ± 10.83
= 3.92 N
700 g Fn = 9.8 m/s2 x 0.7 kg Ff = 1.5 N ± 3.33% = F f / Fn
= 6.86 N = 1.5 N / 9.8 N
= 0.153 ± 3.33%

1000 g Fn = 9.8 m/s2 x 1.0 kg Ff = 1.7 N ± 2.89% = F f / Fn


= 9.8 N = 1.7 N / 6.86 N
= 0.248 ± 2.89%

You might also like