FDB2

A0(A60) Fire And Gas Damper

Halton FDB2 fire dampers are type-approved class A0(A60) fire and gas dampers for use in offshore, marine and navy ventilation systems. The FDB2 can be installed in rectangular or circular ducts. All fire dampers have a fusible link and they prevent the spread of fire and gases within the ventilation ductwork. When the blades are in the open position, the device does not cause significant pressure loss, noise or flow disturbance. Fire dampers are set from outside and can be installed in any position. An open-closed indicator is visible on the outside of the damper. Fire dampers with non-standard dimensions can be supplied on request. Type-approved by most recoganized classification societies, class A0 - A60 fire and gas damper when suitably insulated ATEX approved. Shock tested.
PART Frame Frame Blades Blades Maintenance-free bearings Shafts MATERIAL Carbon steel Stainless steel Steel Stainless steel Stainless steel Stainless steel

Blades contain silicone (effective up to 300 C) for low leakage in normal conditions and thermal expansion graphite seals (effective from 150 C) to increase tightness even up to 50% in a case of fire. Tightness substantially better than NORSOK requirements. (tested size 1000x1000 mm, VTT test report no. RTE4424/04) Nominal fuse release temperature 50 C, 74 C or 100 C. Other temperatures available Low weight due to patented double skin blade structure Automatic electrical, pneumatic or spring operation system available Maximum duct pressure for damper construction 5000 Pa and maximum air velocity 15 m/s. In case of high duct pressure, contact Halton Marine for finding the most suitable solution.
FINISHING Painted or galvanised Galvanized NOTE Bronze bearings optional -

FDB2 - A0(A60) Fire And Gas Damper

3

FDB2 DIMENSIONS AND MATERIAL THICKNESS FDB2 fire dampers meet international standards for both rectangular (width B 100-1200 mm and height H 100-1600 mm, 1 mm division) and circular ducts (100-1250 mm). Non-standard dimensions and flange drilling available on request. Standard flange width 27 mm. Flanges and drilling also available according to ISO 15138 standards. Modular construction sizes up to 2400x3200 mm are available. Standard frame material thickness 3 mm. Frame thickness 3-5 mm according to SOLAS available on request. Frame thickness according to SOLAS
DIMENSIONS If B or H > 100, but < 449 If B or H > 450, but < 649 If B or H > 650 S 3 4 5 L 210 212 215

Actuator effect in dimensions

ACTUATOR DIMENSIONS R Electrical Pneumatic PNL Pneumatic PNR Pneumatic PNR Spring GGA 326.1E Linear actuator 245/300 N Pneumatic rotating actuator AT100 Pneumatic rotating actuator AT200 Spring 100 170 170 190 140 A H<300 = 300 H>300 = H H<500 = 500 H>500 = H H<300 = 300 H>300 = H H<350 = 350 H>350 = H H

The above table contains only some examples of actuators and their effect on dimensions.

GENERAL FDB2 DRAWING

2 1
10

FDB2 CIRCULAR CONNECTIONS

150 n*150

150 n*150 18 30 R
MIN. 50

150 n*150 B+4 10 B+58

MIN. 50

361, S=3 365, S=4 370, S=5

10

GENERAL FDB2 DRAWING, TOP

10

FDB2 CIRCULAR, WITH CONNECTION FLANGES

240, BLADES IN OPEN POSITION

S, ACCORDING TO SOLAS

367, S=3 373, S=4 380, S=5

FDB2 - A0(A60) Fire And Gas Damper

4

S, ACCORDING TO SOLAS

215, S=5 212, S=4 210, S=3

160

S, ACCORDING TO SOLAS

ACTUATOR

H+58

H+4

150 n*150

B+58 FDB2 B+56 FDL max. FDL 1300 max. FDB2 1200 12.0
FLAT BARS TO BE SEALED WITH PYROCRYL SEALANT

DETAIL I

max. FDB2 1600

ACTUATOR

ACTUATOR

S max. FDL 1200

FLAT BAR CROSS STEEL 5*40

FLAT BAR STEEL 5*40

H+58 FDB2

H+56 FDL

ACTUATOR

10.0 FDB2

ACTUATOR

M10*20 8.8

S 10.0 FDB2 9.0 FDL

BOLTED FROM BOTH SIDES

FDB2 PRODUCT OPTIONS Halton FDB2 is available with following actuators: FDB2-EL: Electrical spring return motor; standard actuators being 24 V or 230 V or 120 V. The motor contains built-in open-closed limit switches. Separate junction box included in the EL -model. A wide range of eex-proof actuators available, including a one second closing time function as an option. FDB2-PNL: Pneumatic linear actuator, material AISI 316 FDB2-PNR: Pneumatic rotating actuator FDB2-SP: Manual spring-actuated damper with fusible link. DOT: manual override function available for PNL, PNR and EL models. A wide range of accessories available.

OPERATION PRINCIPLE In the event of a temperature rise in ductwork: FDB2-EL: fusible link releases and cuts off operating voltage to the spring return motor, allowing the spring to close the damper blades. The fire damper opens automatically when the fuse has been changed and the operating voltage to the motor is re-established. FDB2-PNL, FDB2-PNR: fusible link releases and cuts off operating pressure to the spring return actuator, allowing springs to close the damper blades. The fire damper opens automatically when the fuse has been changed and the pneumatic air supply is re-established. FDB2-SP: fusible link releases allowing the spring to close the damper blades. When the fuse has been changed, the fire damper must be reset into open position manually.

WEIGHTS OF STANDARD HALTON MARINE FDB2 DAMPERS (KG) without an actuator

H/Height mm B / Width (mm) 100 5 (5) 7 (7) 9 (9) 11 (11) 13 (16) 15 (18) 18 (25) 20 (27) 22 (31) 24 (33) 26 (36) 28 (39) 31 (42) 32 (45) 35 (48) 36 (51) 200 7 (7) 9 (9) 11 (11) 13 (13) 16 (19) 18 (21) 21 (28) 23 (31) 25 (35) 27 (37) 30 (41) 32 (44) 35 (47) 37 (50) 39 (53) 41 (56) 300 9 (9) 11 (11) 13 (13) 15 (15) 18 (22) 20 (24) 23 (32) 25 (35) 28 (39) 31 (41) 33 (45) 36 (48) 38 (52) 41 (55) 43 (58) 45 (61) 400 10 (10) 12 (12) 15 (15) 17 (17) 21 (25) 23 (27) 26 (35) 28 (38) 32 (42) 34 (45) 37 (49) 39 (52) 42 (56) 45 (59) 48 (63) 50 (66) 500 12 (13) 14 (16) 17 (19) 20 (22) 23 (27) 25 (30) 29 (39) 31 (42) 35 (46) 37 (50) 40 (54) 43 (57) 46 (61) 49 (64) 52 (68) 54 (72) 600 14 (15) 16 (18) 19 (21) 22 (24) 25 (30) 28 (33) 32 (42) 34 (46) 38 (50) 40 (54) 44 (58) 46 (61) 50 (66) 53 (69) 56 (73) 59 (77) 700 15 (22) 18 (26) 21 (30) 24 (33) 28 (38) 30 (41) 34 (46) 37 (50) 41 (54) 44 (58) 47 (62) 50 (66) 54 (70) 57 (74) 60 (78) 63 (82) 800 17 (25) 20 (28) 23 (32) 26 (36) 30 (41) 33 (45) 37 (50) 40 (53) 44 (58) 47 (62) 51 (67) 54 (70) 58 (75) 61 (79) 65 (83) 67 (87) 900 19 (27) 22 (31) 25 (35) 28 (39) 32 (44) 35 (48) 40 (53) 43 (57) 47 (62) 50 (66) 54 (71) 57 (75) 62 (80) 65 (84) 69 (89) 72 (92) 1000 20 (30) 23 (34) 27 (38) 30 (42) 35 (47) 38 (51) 42 (57) 46 (61) 50 (66) 53 (70) 58 (75) 61 (79) 65 (84) 69 (88) 73 (94) 76 (98) 1100 1200 22 (32) 24 (35) 25 (36) 27 (39) 29 (41) 31 (43) 32 (45) 34 (48) 37 (50) 39 (54) 40 (55) 43 (58) 45 (60) 48 (64) 49 (64) 51 (68) 53 (70) 56 (74) 57 (74) 60 (78) 61 (79) 65 (84) 65 (84) 68 (88) 69 (89) 73 (94) 73 (93) 77 (98) 77 (99) 82(104) 81 (103) 85 (108) D2 D mm Weight kg 8 (8) 8 (8) 12 (12) 13 (13) 19 (19) 20 (20) 27 (27) 35 (43) 46 (62) 62 (89) 83 (118) 113 (162)

100 200 300 400 500 600 700 800

900

1000
1100

1200 1300 1400 1500 1600

100 125 160 200 250 315 400 500 630 800 1000 1250

(Frame thickness according to SOLAS)

Examples of actuator weights: FDB2-EL GGA 326.1E 2,3 kg, GNA 326.1E 1,3 kg, BF230 +3,2 kg, BLF230 +1,7 kg, ExMax /Redmax +3,5 kg, FDB2-PNL Roder +4 kg, FDB2-PNR AT100 +2,1 kg, AT100 as AISI316 4,4 kg, AT200 +3,2kg, AT200 as AISI316 +6,2 kg, FDB2-SP +1 kg.

FDB2 - A0(A60) Fire And Gas Damper

5

V4M05Y2010/Halton Marine reserves the right to alter products without notice.

GENERAL FDB2 MODULE ASSEMBLY

9.0 FDL

2.0

FDB2-EL WIRING DIAGRAM

FDB2-PNR/PNL PNEUMATIC DIAGRAM

CLOSED 21 13

21 13 OPEN

POWER DAMPER DAMPER SUPPLY CLOSED OPEN

(-) (+) JUNCTION BOX PC IP66/67

1. SPRING RETURN ACTUATOR 2. QUICK EXHAUST VALVE 3. SILENCER 4. FUSIBLE LINK VALVE
12 13

9
22 14 22 14

1 3 7 2 3 6

1 2 3 4 5 6 7 8 9 10 11
THERMAL FUSE SM-072-A0-2A (72C)

5. OPTION: SOLENOID VALVE 6. MALE CONNECTOR 7. DOUBLE NIPPLE 8. PLASTIC TUBE 9. OPTION: OPEN/CLOSED SWITCHES 10. OPTION: MANUAL VALVE 11. PRESSURE REGULATOR
3 6 6

8 4

8
10

FUSIBLE LINK OPTION: 50/74/100C

12. MALE ELBOW 13. SPEED CONTROLLER

3 6

8
5

S2

S3

S4

S5

S1

S6

24 VDC 230 VAC

87

BF24/BF120/BF230 MOTOR BLF24/BLF230 MOTOR

IP 54

NOTICE! ADDITIONAL SOLENOID VALVE MAX 10 METER FROM FIRE DAMPER PNEU. INLET (5-10 BAR) FOR A PLASTIC TUBE 6 MM

11

FDB2 - A0(A60) Fire And Gas Damper

6