Scribd
Upload
217 views2 pages

Siemens MC45 (DIL/NetPC DNP/9200 - microHOWTO)

This document provides instructions for sending SMS messages using a Siemens MC45 GSM modem connected to a DIL/NetPC DNP/9200. It outlines 4 steps: 1) Copying necessary files, 2) Changing file permissions, 3) Rebooting and initializing the modem, 4) Using AT commands within minicom to send a text message by specifying the recipient number, entering the message body, and finishing with CTRL-Z. The Siemens AT command manual is provided for details on other commands.

Uploaded by

Alex
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
217 views2 pages

Siemens MC45 (DIL/NetPC DNP/9200 - microHOWTO)

This document provides instructions for sending SMS messages using a Siemens MC45 GSM modem connected to a DIL/NetPC DNP/9200. It outlines 4 steps: 1) Copying necessary files, 2) Changing file permissions, 3) Rebooting and initializing the modem, 4) Using AT commands within minicom to send a text message by specifying the recipient number, entering the message body, and finishing with CTRL-Z. The Siemens AT command manual is provided for details on other commands.

Uploaded by

Alex
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DIL/NetPC DNP/9200 microHOWTO

How to send a SMS with the Siemens MC45 GSM Modem


SMS (Short Message Service) is a way to transfer short text messages over a GSM-based mobile phone network. Messages are sent via a store-and-forward mechanism to a Short Message Service Centre (SMSC), which will attempt to send the message to the recipient and possibly retry if the user is not reachable at a given moment. The DIL/NetPC DNP/9200 and the evaluation board DNP/EVA9 support SMS, if the Sony Ericsson or Siemens MC45 GSM modem is installed. It is also necessary to insert a SIM card with a valid GSM phone network provider contract or a prepaid account to the DNP/EVA9 SIM card holder. 1. Step: Copy all files from the directory /gsm of the DNP/9200 starter kit CD-ROM (version 1.2 or later) to the DNP/9200 directory /flash. Please use the following TFTP commands for this job: tftp tftp tftp tftp g g g g l l l l autoinit.sh 192.168.0.1 minicom 192.168.0.1 minirc.dfl 192.168.0.1 mod_pwr 192.168.0.1

2. Step: The two files minicom and mod_pwr needs executable rights. Please use the following Linux shell command lines and change the rights: chmod +x minicom chmod +x mod_pwr

3. Step: Reboot your DIL/NetPC DNP/9200. The DNP/9200 executes mod_pwr over the shell script autoinit.sh within the Linux booting phase and turns the Siemens MC45 GSM modem power on. Then run a Telnet session and enter the following two commands: cd /flash ./minicom With the help of these two commands we run the minicom program, a simple terminal emulation for the DNP/9200. This program allows us to use the Siemens MC45 GSM modem with AT commands.

SSV EMBEDDED SYSTEMS 2006, mHT9200-16.doc, Rev. 1.00.

DIL/NetPC DNP/9200 microHOWTO

4. Step: Within the minicom terminal emulation window, please execute the following AT commands (use the enter key after each AT command line the Siemens MC45 GSM modem responds with OK): at at+cpin? at+cpin=... pin number ... at+cmgf=1 at+csmp=17,167,0,0

The first AT commands initializes the Siemens MC45 GSM modem with the PIN number (this number depends on your SIM card) and some SMS mode parameters. Then enter the at+cmgs command for sending the SMS: at+cmgs=... recipient phone number ... The GSM modem responds to the at+cmgs command with a single > character. Now enter your text message and finish the text with CTRL-Z. After that, the GSM modem sends the SMS to the recipient. For more details about the GSM modem AT commands, please see the Siemens Mobile GSM Modem: MC45 AT Command Set Manual. This manual is a part of your DNP/9200 starter kit CD-ROM Please note: The AT command sample shown within the last picture use the PIN number 3774 and the recipient phone number +491736110914. Please replace these placeholders with your numbers. For leaving the minicom terminal emulation program, please enter CTRL-A followed by the single character X. That is all. 2

SSV EMBEDDED SYSTEMS 2006, mHT9200-16.doc, Rev. 1.00.

You might also like