Scribd
Upload
157 views

Curso Leak Detection

The document discusses methods for leak detection in closed vessels. It describes two main methods: vacuum methods where the vessel is evacuated and pressure increases are measured, and overpressure methods where the vessel is pressurized and pressure decreases are measured. It then provides details on several leak detection techniques for localizing and quantifying leaks including pressure rise methods, sniffing with detectors, and integral hood tests. Finally, it covers the operating principles and parameters of helium leak detectors used to precisely measure leak rates.

Uploaded by

Durgamadhaba Mishra
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
157 views

Curso Leak Detection

The document discusses methods for leak detection in closed vessels. It describes two main methods: vacuum methods where the vessel is evacuated and pressure increases are measured, and overpressure methods where the vessel is pressurized and pressure decreases are measured. It then provides details on several leak detection techniques for localizing and quantifying leaks including pressure rise methods, sniffing with detectors, and integral hood tests. Finally, it covers the operating principles and parameters of helium leak detectors used to precisely measure leak rates.

Uploaded by

Durgamadhaba Mishra
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 21

Chapter 6 Leak detection

1. Leak rate

V p qL = t

mbar ls-1

A leak rate of 1 mbar ls-1 exists in a closed vessel having a volume of 1 liter when the pressure increases by 1 mbar within one second, or in case of an overpressure it decreases by 1 mbar within one second.

2. Leak Detection Methods


z Vacuum Methods The equipment to be tested is evacuated. The pressure ratio between inside and outside is 0:1. z Overpressure Methods The equipment to be tested is pressurized with a search gas or a search gas mixture. The pressure ratio between inside and outside is over 1:1.
5

General Notes 1. The lowest leak rates can only be measured by employing the vacuum method, whereby the following applies: The lower the leak rate, the higher the requirements are concerning cleanness and ultimate vacuum. 2. If possible the test objects should be tested under the same conditions that will be used in their final application, i.e. parts for vacuum operation should be tested according to the vacuum method and parts for overpressure operation should be tested using the overpressure method.

2.1 Leak Testing Based on Vacuum Methods


1. Pressure Rise Method
a) shows the theoretical pressure rise if there is only a leak. b) shows the pressure rise due to outgassing from the surfaces of the test object. c) shows the pressure rise as it occurs in practice, where outgassing and leak rate add.

2. Local Leak Detection

1 Test object 2 Leak detector 3 Search gas cylinder 4 Vacuum pump 5 Spray gun for search gas
8

3. Integral Method

1 Test object 2 Leak detector 3 Search gas cylinder 4 Vacuum pump 5 Hood 6 Spray gun for search gas 7 Sniffer probe
9

2.2 Leak Testing Based on Overpressure Methods


1. Pressure Drop Method The test object is filled with a gas determination of gross leaks applying soap solutions or similar, leaks can be located.

10

2. Local Leak Detection with Leak Detectors Sniffing

1 Test object 2 Leak detector 3 Search gas cylinder 7 Sniffer probe


11

3. Integral Method Hood Test

1 Test object 2 Leak detector 3 Search gas cylinder 5 Hood 7 Sniffer probe
12

4. Integral Method Vacuum Hood Test

1 Test object 2 Leak detector 3 Search gas cylinder 4 Vacuum pump 5 Hood
13

5. Integral Method Bombing-Test


This method is used for testing hermetically sealed components such as transistors, IC-packages or dry reed relays.

Operating principle:
1.The test objects are placed in a vessel which is pressurized with the search gas - preferably helium. 2. At a fairly high search gas pressure and after a period of up to several hours it is tried to enrich the search gas inside leaky test objects. 3. After this, the test objects are transferred to a vacuum chamber 4. Their total leak rate is determined in the same way as in the vacuum hood test.

14

3. Helium Leak Detectors


3.1. Applications: a. Localization of leaks b. Quantitative determination of the leak rate, i.e. the gas flow through the leak. A leak detector is therefore a helium flow meter.

15

3.2 Operating Principle a. Evacuating the part which is to be tested. b. Gas from the outside may enter through an existing leak due to the pressure difference present. c. If only helium is brought in front of the leak , this helium flows through the leak and is pumped out by the leak detector. d. The helium partial pressure present in the leak detector is measured by a sector mass spectrometer and is displayed as a leak rate. e. Leak rate. is usually given in terms of volume flow of the helium (pV-flow).
16

3.3 Parameters of helium leak detector


Measurement range (detection limits)

The lowest and the highest detectable leak rate The sum of noise amplitude and zero drift per minute Response time. Time it takes from spraying the test object with helium until a measured value is displayed by the leak detector. Response time for helium tA = 3V/SHe (for 95% of the final value) with V = Volume of the test object SHe = Volume flow rate for helium at the point of the test object
17

3.4 Operation mode


1. Main Flow Method 2. Counterflow Method 3. Partial Flow Method

18

Main Flow Method


Advantages: Highest sensitivity, detection limit i.e. low

Short response time due to a high volume flow rate at the inlet. Disadvantage a liquid nitrogen cold trap

19

Counterflow Method
The test object is connected to the forevacuum The entire gas flow (especially water vapor) does not contribute to the pressure increase in the mass spectrometer. A cold trap is no longer required! Advantages: No liquid nitrogen is required High permissible inlet pressures (i.e. pressure within the test object)

20

Partial Flow Method


Higher leak rates Operation at higher inlet pressures At pressures above the normal inlet pressure (main flow: above 10-2 mbar, counterflow: above 10-1 mbar) In the case of high helium leak rates, The inlet valve is closed The main flow is allowed to enter the partial flow pump, whereas only a small part enters the leak detector. Thus the total pressure and the helium pressure are dropped to values suitable for operation of the leak detector. .
21

You might also like