SPECIFICATION 1 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Charlie 2G and 3G

Field Test Display Specification

Status: Approved
Version: 1.0
Doc. number: DTS08337-EN-1.0
Date: 8.4.2004
Author: Jari.P.Jokinen
Approval: Tero Tamminiemi
Function: Field Testing
File Name: Charlie_FTD_specification_1.0.doc
File location: Notes: \\eslns47\NMP\PCP\WCDMA\IBU DocMan

Change history:

1.0 8.4.2004 Jari Jokinen Approved Modified and approved

0.1 6.4.2004 Jari Jokinen Draft Charlie 2G FTD v. 1.0
and Charlie 3G FTD v.
0.4 were put together
 SPECIFICATION 2 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

1 INTRODUCTION..........................................................................................................................9
2 USING THE FIELD TEST DISPLAYS ..........................................................................................9
2.1 General..................................................................................................................................9
2.2 Activating the Field Test Displays ..........................................................................................9
2.3 Deactivating the Field Test Displays ....................................................................................10
2.4 Field Test Display modes.....................................................................................................10
2.4.1 Modes belonging in the use of the displays...................................................................10
2.4.2 Modes belonging in the field test display data...............................................................11
Signal and battery level ..................................................................................................................12
3 Information on the displays ........................................................................................................12
Group 01: GSM Signaling displays, which can be visible to network operators ..............................14
Display 01.01: Information of the serving cell (Version: 3.25, Status: Approved) ........................14
Display 01.02: More information of the serving cell (Version: 1, Status: Approved) ....................16
Display 01.03: Information of the serving cell, 1st and 2nd neighbor (Version: 3.25, Status:
Approved) ..................................................................................................................................17
Display 01.04: Information of the 3rd, 4th and 5th neighbor (Version: 3.25, Status: Approved) ..18
Display 01.05: Information of the 6th, 7th and 8th neighbor (Version: 3.25, Status: Approved)...20
Display 01.06: Network selection display (Version: 1, Status: Approved) ...................................21
Display 01.07: System information bits for serving cell (Version: 3.19, Status: Approved)..........22
Display 01.08: Paging repeat period, TMSI, periodic location update, AFC and AGC (Version: 3.19,
Status: Approved) ......................................................................................................................23
Display 01.09: Network parameters (Version: 4.0, Status: Approved) ........................................24
Display 01.10: Ciphering, hopping DTX status and IMSI (Version: 1, Status: Approved) ............25
Display 01.11: Uplink DTX switching display (Version: 1, Status: Approved)..............................26
Display 01.12: Storing and removing BTS_TEST carrier (Version: 3.13, Status: Approved) .......27
Display 01.13: Toggle Cell Barred Status (Version: 1, Status: Approved)...................................28
Display 01.14: Modify "last used band" (Version: 1, Status: Approved) ......................................29
Group 02: GSM Registration and Mobility Displays ........................................................................31
Display 02.01: Reset Registration and Mobility counters (Version: 1, Status: Approved)............31
Display 02.02: Neighbor Measurement Counter Display (Version: 1, Status: Approved) ............31
Display 02.03: Search and reselection counter display (Version: 1, Status: Approved) ..............32
Display 02.04: Location update attempts counters (Version: 1, Status: Approved) .....................33
Display 02.05: Handover display, INTER CELL (Version: 1, Status: Approved)..........................33
Display 02.06: Handover display, INTRA CELL (Version: 1, Status: Approved).........................34
Display 02.07: L2 display (Version: 1, Status: Approved) ...........................................................35
Group 03: GSM memory handling..................................................................................................37
Display 03.01: SIM information 1 (Version: 1, Status: Approved) ...............................................37
Display 03.02: SIM information 2 (Version: 1, Status: Approved) ...............................................37
Group 04: GSM Test Timers, SMS and Call Counter Displays .......................................................39
Display 04.01: Reset test timers to zero and restart them (Version: 1, Status: Approved) ..........39
Display 04.02: Enable or disable test timers (Version: 1, Status: Approved)...............................39
Display 04.03: Test timer display (Version: 1, Status: Approved) ...............................................40
Display 04.04: Reset SMS and Call Counters to zero (Version: 1, Status: Approved) ................41
With this display all counters listed on the Display 04.05: Call attempts counters (Version: 1, Status:
Approved), .................................................................................................................................41
Display 04.05: Call attempts counters (Version: 1, Status: Approved) ........................................41
Display 04.06: Information about reasons for call clearing (Version: 1, Status: Approved) .........42
Display 04.07: SMS attempts counters (Version: 1, Status: Approved) ......................................43
Display 04.08: SMS timeout counters (Version: 1, Status: Approved) ........................................43
 SPECIFICATION 3 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 04.09: Toggle transmitter functionality (Version: 1, Status: Approved) ...........................44

Group 05: GSM Data Displays .......................................................................................................46
Display 05.01: HSCSD, Timeslot information display (Version: 3.19, Status: Approved) ............46
Display 05.02: HSCSD, Timeslot power control level display (Version: 3.19, Status: Approved) 46
Display 05.03: Transparent data information (Version: 1, Status: Approved)..............................47
Display 05.04: Non transparent data (Version: 1, Status: Approved) ..........................................48
Display 05.05: Facsimile information (Version: 1, Status: Approved)..........................................49
Display 05.06: CSD Server, main data display (Version: 1, Status: Approved)...........................50
Display 05.07: CSD Server, active DTE info 1/2, call related info (Version: 3.13, Status: Approved)
...................................................................................................................................................52
Display 05.08: CSD Server, active DTE info 2/2, GPDS, socket, conference info (Version: 1, Status:
Approved) ..................................................................................................................................53
Display 05.09: GPRS Rel99 Display (Version: 1, Status: Approved) ..........................................54
Display 05.10: MAC Interface Display (Version: 1, Status: Approved) ........................................56
Display 05.11: CSD Server Main Data Display, Control 2001 (Version: 1, Status : Approved)....57
Display 05.12: Control DTE and Call Info Displays, Control 2001 (Version: 1, Status: Approved)58
Display 05.13: Active DTE Display xx, Control 2001 (Version: 1, Status: Approved) ..................59
Display 05.14: Active Call Display (Version: 1, Status: Approved) ..............................................61
Display 05.15: Common CSD Display (Version: 1, Status: Approved)........................................62
Display 05.16: Current BC-IE (Version: 1, Status: Approved) .....................................................63
Display 05.17: LLC (Version: 1, Status: Approved).....................................................................64
Group 06: GPRS Signaling displays...............................................................................................66
Display 06.01: Information of the current GPRS state and previous TBF configuration (Version:
3.17, Status: Approved)..............................................................................................................66
Display 06.02: Previous UL TBF establishment (Version: 3.15, Status: Approved).....................67
Display 06.03: Information of the GMM state (Version: 5.0, Status: Approved)...........................68
Display 06.04: Values of P-TMSI, RAC, SMS radio priority, Ciphering and Non-DRX parameters
(Version: 3.15, Status: Approved) ..............................................................................................69
Display 06.05: GPRS Network parameters (Version: 3.15, Status: Approved)...........................70
Display 06.06: Packet control channel parameters (Version: 4.0, Status: Approved)..................71
Display 06.07: (Packet) System information parameters (Version: 5.0, Status: Approved) .........71
Display 06.08: Cell re-selection parameters (serving cell) (Version: 3.15, Status: Approved) .....72
Display 06.09: GPRS information of the serving cell, 1st, 2nd, and 3rd neighbor (Version: 3.19, Status:
Approved) ..................................................................................................................................73
Display 06.10: GPRS information of the 4th,5th and 6th neighbor (Version: 3.15, Status: Approved)75
Display 06.11: GPRS information of the serving cell and 6 neighbors (Version: 3.16, Status:
Approved) ..................................................................................................................................76
Display 06.12: EGPRS specific parameters (Version: 3.24, Status: Approved) ..........................78
Display 06.13: EGPRS BEP parameters (Version: 5.0, Status: Approved) .................................79
Group 07: GPRS Data protocol displays ........................................................................................80
Display 07.01: Information of the first active PDP context (Version: 3.22, Status: Approved) ....80
Display 07.02: Information of the second active PDP context (Version: 3.22, Status: Approved)81
Display 07.03: Information of the RLC state (Version: 1, Status: Approved) ...............................82
Display 07.04: RLC parameters (Version: 1, Status: Approved) .................................................83
Display 07.05: RLC data block counters (Version: 1, Status: Approved) ....................................83
Display 07.06: LLC data block counters (Version: 1, Status: Approved) .....................................84
Display 07.07: LLC Ciphering parameters (Version: 1, Status: Approved)..................................84
Display 07.08: LLC parameters of the first SAPI (Version: 1, Status: Approved) ........................85
Display 07.09: LLC parameters of the second SAPI (Version: 1, Status: Approved)...................86
Display 07.10: SNDC Data counters (Version: 1, Status: Approved) ..........................................86
Display 07.11: PPP information (Version: 1, Status: Approved)..................................................87
Display 07.12: ERLC Data information_1 (Version: 3.32, Status: Approved) ..............................87
Display 07.13: ERLC Data information_2 (Version: 3.12, Status: Approved) ..............................88
 SPECIFICATION 4 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 07.14: ERLC Data counters (Version: 3.12, Status: Approved)......................................88

Display 07.15: System status (Version: 5.0, Status: Approved) ..................................................89
Display 07.16: Information of the selected PDP context (Version: 5.0, Status: Approved) ..........89
Display 07.17: QoS of the selected PDP context 1 (Version: Charlie spec) ................................91
Display 07.18: QoS of the selected PDP context 2 (Version: Charlie spec) ................................92
Display 07.19: PDCP parameters of the selected PDP context (Version: 3.22, Status: Approved)92
Display 07.20: RFC2507 parameters of the selected PDP context (Version: 3.22, Status: Approved)
...................................................................................................................................................93
Group 08: GPRS Measurement displays........................................................................................96
Display 08.01: Power control parameters (Version: 3.19, Status: Approved)..............................96
Display 08.02: The previous channel quality report (Version: 3.20, Status: Approved) ...............97
Display 08.03: NC and EM parameters (Version: 1, Status: REJECTED)...................................97
Display 08.04: The previous NC report, part 1 (Version: 1, Status: REJECTED) ........................98
Display 08.05: The previous NC report, part 2 (Version: 1, Status: REJECTED) ........................99
Display 08.06: The previous EM report, part 1 (Version: 1, Status: REJECTED)......................100
Display 08.07: The previous EM report, part 2 (Version: 1, Status: REJECTED)......................100
Display 08.08: Downlink power control parameters (Version: 1, Status: REJECTED) ..............101
Group 09: GPRS Test counter displays........................................................................................103
Display 09.02: TBF counters (Version: 5.0, Status: Approved) .................................................103
Display 09.10: GPRS attach and detach counters (Version: 5.0, Status:Approved)..................104
Display 09.11: Periodic routing area update counters (Version: 5.0, Status: Approved) ...........105
Display 09.12: Routing area update counters (Version: 5.0, Status: Approved)........................105
Display 09.13: PDP context counters (Version: 5.0, Status: Approved) ....................................106
Display 09.14: SMS over GPRS counters (Version: 5.0, Status: Approved) .............................107
Display 09.17: MS initiated cell re-selection counters (Version: 5.0, Status: Approved)............108
Display 09.18: Network initiated cell re-selection counters (Version: 5.0, Status: Approved) ....109
Group 10: GSM DSP displays ......................................................................................................110
Display 10.01: DSP Data Display 1 (Version: 1, Status: Approved) ..........................................110
Display 10.02: DSP Data Display 2 (Version: 1, Status: Approved) ..........................................110
Display 10.03: DSP Data Display 3 (Version: 1, Status: Approved) ..........................................111
Display 10.04: FER measuments for sub ch0: REAL, FULL and SUB values (Version: 3.24, Status:
Approved) ................................................................................................................................112
Display 10.05: FER measuments for sub ch1: REAL, FULL and SUB values (Version: 3.25, Status:
Approved) ................................................................................................................................113
Display 10.06: FER measuments for sub ch2: REAL, FULL and SUB values (Version: 3.25, Status:
Approved) ................................................................................................................................114
Group 11: CDSP GSM AMR displays...........................................................................................115
Display 11.01: AMR1:Information of the Active Mode Set (Version: 3.16, Status: Approved) ...115
Display 11.02: AMR2: Information of the mode control (Version: 3.16, Status: Approved)........116
Display 11.03: AMR3: Information of the link quality estimation (Version: 3.16, Status: Approved)
.................................................................................................................................................117
Display 11.04: AMR4: Control AMR FTD data pre processing (Version: 1, Status: Approved) .119
Display 11.05: AMR5: Control AMR algorithms (Version: 1, Status: Approved) ........................119
Group 12: CDSP SW Platform .....................................................................................................121
Display 12.01: CDSP version and date (Version: 3.13, Status: Approved) ...............................121
Display 12.02: Reset display (Version: 1, Status: Approved)....................................................121
Display 12.03: CDSP error and reset counters and MCU reset time (Version: 3.13, Status:
Approved) ................................................................................................................................122
Display 12.04: Counters for specific CDSP non-fatal errors (Version: 1, Status: Approved) .....123
Display 12.05: CDSP fatal error codes (Version: 3.13, Status: Approved) ................................124
Display 12.06: CDSP non-fatal error codes (Version: 1, Status: Approved)..............................125
Display 12.07: CDSP fatal error code timestamps (Version: 3.31, Status: Approved)...............126
Display 12.08: CDSP non-fatal error code timestamps (Version: 3.31, Status: Approved)........127
 SPECIFICATION 5 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 12.09: Counters for failed application starts (Version: 1, Status: Approved).................128
Display 12.10: Common CDSP test data display (Version: 3.22, Status: Approved).................129
Group 41: WCDMA CDSP displays..............................................................................................131
Display 41.01: RACH MSG TX profile (Version: 3.19, Status: Approved) .................................131
Display 41.02: Dedicated uplink channel power control status (Version: 3.24, Status: Approved)132
Display 41.03: Dedicated downlink channel power control status (Version: 3.19, Status: Approved)
.................................................................................................................................................133
Display 41.04: WCDMA AFC status (Version: 3.13, Status: Approved) ....................................134
Display 41.05: CDSP load status (Version: 3.19, Status: Approved) ........................................135
Display 41.06: Downlink receiver gain control status (Version: 3.28, Status: Approved)...........136
Display 41.07: WCDMA rake receiver status (Version: 3.13, Status: Approved).......................137
Display 41.08: WCDMA decoder status (Version: 3.13, Status: Approved) ..............................138
Display 41.09: Common WCDMA DSP CS scratchpad display (interactive) (Version: 3.19, Status:
Approved) ................................................................................................................................139
Display 41.10: FDD neighbour cell summary (Version: 3.13, Status: Approved).......................140
Display 41.11: FDD ranking summary (Version: 3.24, Status: Approved) .................................141
Display 41.12: FDD Frequency summary (Version: 3.13, Status: Approved)............................142
Display 41.13: FDD intra frequency neighbour summary (Version: 3.13, Status: Approved) ....143
Displays 41.14 – 41.15: FDD inter frequencies 1 and 2 neighbour summary (Version: 3.13, Status:
Approved) ................................................................................................................................146
Display 41.16: FDD mode GSM cell detection summary (Version: 3.13, Status: Approved) ....148
Display 41.17: FDD detailed cell info (interactive): (Version: 3.16, Status: Approved) .............149
Groups 42-45: WCDMA Layer 1 Field Test Displays....................................................................151
Group 46: WCDMA RAN System displays ...................................................................................152
Display Display 46.01: RRC Global Status (Version: 6.2, Status: Approved)............................152
Display 46.02: PEER message MSC (Version: 6.2, Status: Approved) ....................................152
Display 46.03: RNTI Values (Version: 6.2, Status: Approved) ..................................................154
Display 46.04: Ciphering Capability (Version: 6.2, Status: Approved).......................................155
Display 46.05: Cell Selection - Screen 2 (Version: 6.2, Status: Approved) ...............................155
Display 46.06: FDD BTS Carrier Lock Mode (Version: 6.2, Status: Approved) .........................156
Display 46.07: Counter Reset (Version: 6.2, Status: Approved) ...............................................156
Display 46.08: Call Failure Reasons (Version: 6.2, Status: Approved) .....................................157
Display 46.09: L1 State (Version: 6.2, Status: Approved) .........................................................158
Display 46.10: Cell Reselection - Screen 1 (Version: 6.2, Status: Approved) ...........................158
Display 46.11: Radio Access Bearer Information (Version: 6.2, Status: Approved) ..................159
Display 46.12: Radio Bearer Information (Version: 6.2, Status: Approved)...............................160
Display 46.13: Radio Bearer Information (Version: 6.2, Status: Approved)...............................161
Display 46.14: DPCH Change Count (Version: 6.2, Status: Approved) ....................................162
Display 46.15: Tracker Feature Enable/Disable (Version: 6.2, Status: Approved) ....................162
Display 46.27: Voice RLC-U Information (Version: 6.2, Status: Approved) ...............................163
Display 46.28: DTX Enable/Disable input (Version: 6.2, Status: Approved)..............................164
Display 46.60: 3G to 2G Reselections (Version: 6.2, Status: Approved)...................................164
Display 46.61: 3G to 2G ISHO #1 (Version: 6.2, Status: Approved) .........................................165
Display 46.62: 3G to 2G ISHO #2 (Version: 6.2, Status: Approved) .........................................166
Display 46.63: 3G to 2G ISHO #3 (Version: 6.2, Status: Approved) .........................................167
Group 47: WCDMA RRC displays ................................................................................................169
Display 47.01: RRC Global State Change Counters (Version: 6.2, Status: Approved)..............169
Display 47.02: Counters for Timeouts - Screen 1 (Version: 6.2, Status: Approved) ..................169
Display 47.03: Counters for Timeouts - Screen 2 (Version: 6.2, Status: Approved) ..................170
Display 47.04: Peer Message Count- Screen1 (Version: 6.2, Status: Approved)......................171
Display 47.05: Peer Message Count- Screen2 (Version: 6.2, Status: Approved)......................172
Display 47.06: Peer Message Count-Screen3 (Version: 6.2, Status: Approved).......................172
Display 47.07: Peer Message Count-Screen4 (Version: 6.2, Status: Approved).......................173
 SPECIFICATION 6 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 47.08: Peer Message Count-Screen5 (Version: 6.2, Status: Approved).......................174

Display 47.09: Peer Message Count-Screen6 (Version: 6.2, Status: Approved).......................175
Display 47.10: Peer Message Count-Screen7 (Version: 6.2, Status: Approved).......................176
Group 48: WCDMA RLC displays ................................................................................................177
Display 48.01: Set AM Bearer ID (Version: 6.2, Status: Approved)...........................................177
Display 48.02: RLC AM State information (Version: 6.2, Status: Approved) .............................177
Display 48.03: RLC AM Counters 1 (Version: 6.2, Status: Approved).......................................178
Display 48.04: RLC AM Counters 2 (Version: 6.2, Status: Approved).......................................178
Display 48.05: RLC AM Counters 3 (Version: 6.2, Status: Approved).......................................179
Display 48.06: RLC AM Counters 4 (Version: 6.2, Status: Approved).......................................180
Display 48.07: RLC AM Counters 5 (Version: 6.2, Status: Approved).......................................180
Display 48.08: RLC AM Counters 6 (Version: 6.2, Status: Approved).......................................181
Display 48.09: RLC AM Tx Buffer Occupancy (Version: 6.2, Status: Approved) .......................182
Group 49: WCDMA MAC displays................................................................................................183
Display 49.01: Basic Radio Bearer Information (Version: 6.2, Status: Approved) .....................183
Display 49.02: Basic DCH Information (Version: 6.2, Status: Approved) ..................................184
Display 49.04: Radio Bearer ID and SUB ID input (Version: 6.2, Status: Approved).................186
Display 49.05: Radio Bearer Information (Version: 6.2, Status: Approved)...............................186
Display 49.06: Input DCH ID (Version: 6.2, Status: Approved) .................................................188
Display 49.07: DCH Information (Version: 6.2, Status: Approved) ............................................189
Group 50: WCDMA WPH displays ...............................................................................................191
Display 50.01: WPH Connection counts (Version: 6.2, Status: Approved)................................191
Display 50.10: WPH L1 Received Error Codes (Version: 6.2, Status: Approved) .....................191
Display 50.11: WPH L1 Received Error Timestamp (Version: 6.2, Status: Approved) ..............192
Display 50.12: WPH L1 PId list before error (Version: 6.2, Status: Approved) ..........................193
Display 50.13: WPH L1 Rx signal list before error (Version: 6.2, Status: Approved).................194
Display 50.14: WPH L1 Tx signal list before error (Version: 6.2, Status: Approved) .................195
Display 50.15: WPH L1 list of previous warnings received before error (Version: 6.2, Status:
Approved) ................................................................................................................................196
Group 61: Common EM (Energy Management) displays..............................................................198
Display 61.01: Basic EM information (Version: 3.16, Status: Approved)...................................198
Display 61.02: Basic BATMON4 information (Version: 1, Status: Approved) ............................199
Display 61.03: Advanced BATMON4 algorithm information (Version: 1, Status: Approved)......200
Display 61.04: Battery Monitor setup and log information (Version: 1, Status: Approved).........201
Display 61.05: PSM (Phone State Monitor) information 1 (Version: 3.16, Status: Approved)....202
Display 61.06: PSM (Phone State Monitor) information 2 (Version: 1, Status: Approved).........203
Display 61.07: PSM (Phone State Monitor) information 3 (Version: 3.16, Status: Approved)....203
Display 61.08: Basic charging information (Version: 1, Status: Approved)................................204
Display 61.09: Extended charging information (Version: 1, Status: Approved) .........................205
Display 61.10: Extended charging information 2 (Version: 3.16, Status: Approved) .................207
Display 61.11: Configuration parameters etc. (Version: 3.16, Status: Approved)......................208
Display 61.12: Varying EM information 1 (Version: 3.15, Status: Approved).............................208
Display 61.13: Varying EM information 2 (Version: 3.15, Status: Approved).............................209
Group 62: Common general displays ...........................................................................................210
Display 62.01: Reasons for SW resets (Version: 3.32, Status: Approved) ................................210
Display 62.02: Counters for resets 1 (Version: 3.32, Status: Approved) ...................................211
Display 62.03: Counters for resets 2 (Version: 3.19, Status: Approved) ...................................212
Display 62.04: Counters for DSP resets (Version: 3.32, Status: Approved) .............................213
Display 62.06: Lights status control (Version: 1, Status: Approved)..........................................214
Display 62.07: Disabling R&D Test Displays (Version: 1, Status: Approved) ............................214
Display 62.08: Reliability Test Display (Version: 1, Status: Approved)......................................215
Display 62.10: Information about MCU and DSP software versions (Version: 3.23, Status:
Approved) ................................................................................................................................215
 SPECIFICATION 7 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 62.11: Information about HW version (Version: 3.18, Status: Approved)......................216

Display 62.12: Information about PPM (Version: 3.24, Status: Approved) ................................216
Group 63: Common OS status displays .......................................................................................218
Display 63.01: OS Block usage statistics (Blocks 1-8) (Version: 3.19, Status: Approved).........218
Display 63.02: OS Block usage statistics (Blocks 9-16) (Version: 3.19, Status: Approved).......219
Display 63.03: OS block allocation errors (Version: 3.32, Status: Approved)............................220
Display 63.04: Memory status before reset (Version: 3.19, Status: Approved) .........................220
Display 63.05: OS pre-reset error status (Version: 3.32, Status: Approved) .............................221
Display 63.06: OS current error status (Version: 3.31, Status: Approved) ................................222
Display 63.07: OS pre-reset warning status (Version: 3.31, Status: Approved) ........................222
Display 63.08: OS current warning status (Version: 3.31, Status: Approved) ...........................223
Display 63.09: OS pre-reset remark status (Version: 3.31, Status: Approved)..........................224
Display 63.10: OS current remark status (Version: 3.31, Status: Approved).............................224
Display 63.11: Heap system status (Version: 3.19, Status: Approved) .....................................225
Display 63.12: Heap top users (Version: 3.31, Status: Approved) ............................................226
Display 63.13: Failed assertions (Version: 3.19, Status: Approved)..........................................226
Display 63.14-63.29: Reserved for future use (Version: 1, Status: - ) .......................................227
Display 63.30: Information of OS_SYSTEM_STACK (Version: 3.19, Status: Approved) ..........227
Display 63.31: Select task set (Version: 3.19, Status: Approved) .............................................227
Displays 63.32 – 63.99: Information about tasks (Version: 3.31, Status: Approved) .................228
Group 64: Common Audio displays ..............................................................................................230
Display 64.01: Read DSP Memory (Version: 3.13, Status: Approved)......................................230
Display 64.02: Signal generators (Version: 3.13, Status: Approved).........................................231
Display 64.03: Accesory mode status (Version: 3.13, Status: Approved) .................................231
Display 64.04: Downlink audio display (Version: 3.13, Status: Approved) ................................232
Display 64.05: Uplink audio display (Version: 3.13, Status: Approved).....................................233
Display 64.06: Microphone Active Gain Control (AGC) (Version: 3.13, Status: Approved) .......233
Display 64.07: Acoustic Echo Canceller (AEC) (Version: 3.13, Status: Approved) ...................234
Display 64.08: Dynamic/Multi-Band Range Controller (DRC/MDRC) (Version: 3.13, Status:
Approved) ................................................................................................................................235
Display 64.09: Control DSP audio enhancements switch 1 (Version: 3.15, Status: Approved) .236
Display 64.10: Control DSP audio enhancements switch 2 (Version: 3.15, Status: Approved) .237
Display 64.11: Control DSP audio enhancements switch 3 (Version: 3.15, Status:Approved) ..238
Display 64.12: SpCs (Version: 3.13, Status: Approved)............................................................239
Display 64.13: SpC counters (Version: 3.16, Status: Approved)...............................................239
Group 65: Common PPC (Product Performance Counters) displays............................................241
Display 65.01: PPC Counters 1 (Version: 3.19, Status: Approved)...........................................241
Display 65.02: PPC Counters 2 (Version: 3.19, Status: Approved)...........................................241
Display 65.03: PPC Counters 3 (Version: 3.19, Status: Approved)...........................................242
Display 65.04: Camera PPCs (Version: 3.27, Status: Approved)..............................................242
Display 65.05: HW UI counters (Version: 3.28, Status: Approved) ...........................................243
Group 73: Common Accessory displays.......................................................................................245
Display 73.01: Accessory mode information 1 (Version: 1, Status: Approved)..........................245
Display 73.02: Accessory mode information 2 (Version: 1, Status: Approved)..........................245
Display 73.03: Accessory mode information 3 (Version: 1, Status: Approved)..........................246
Display 73.04: Vibra information (Version: 1, Status: Approved) ..............................................246
Display 73.06: Ambient light sensor information 1 (Version: 1, Status: Approved )...................247
Display 73.07: Ambient light sensor information 2 (Version: 1, Status: Approved )..................248
Group 74: Common Memory Management displays.....................................................................249
Display 74.01: Information of MeM component versions (Version: 1, Status: Approved) ..........249
Display 74.02: Information of PMM Plain area (Version: 1, Status: Approved) .........................249
Display 74.03: Information of PMM Classified area (Version: 1, Status: Approved) ..................250
Display 74.04: Information of PMM Protected area (Version: 1, Status: Approved) ..................250
 SPECIFICATION 8 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 74.05: PMM Storing information (Version: 1, Status: Approved) ..................................251

Display 74.06: PMM Error information 1 (Version: 1, Status: Approved)...................................252
Display 74.07: PMM Error information 2 (Version: 1, Status: Approved)...................................252
Display 74.08: Information of PMM Clean-up (Version: 1, Status: Approved) ...........................253
Group 81: Multimode protocol displays ....................................................................................253
Display 81.01: Force protocol between GSM and WCDMA (Version: 3.26, Status: Approved).253
Display 81.02: Toggle Integrity Protection Mode (Version: 3.26, Status: Approved) .................254
Group 99: Charlie specific displays ..............................................................................................256
Display 99.01: PPC Counters...................................................................................................256
Display 99.04: Einfo on FTD.....................................................................................................256
4 REFERENCES.........................................................................................................................257
 SPECIFICATION 9 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

1 INTRODUCTION

This document specifies the features of Charlie Field Test Displays. Field Test Display, i.e.
engineering test mode, is a configurable software feature that is available in application list.
Field Test Display is useful for testing mobile phones during development or for verifying the
operation of the network.

2 USING THE FIELD TEST DISPLAYS

2.1 General

When the Field Test Display is active, the phone can be used in a similar way than without it.
When application key is pressed FTD will stay on backround and it can be activated again by pressing
application key for about one second and after that select.

It is possibly to disable FTD from display 62.07 and after that FTD application icon will be deleted.
FTD can be restored installing it again.

NOTE: FTD application should not interfere phone operation, because of allmost all field testing will
be made so that FTD is in active mode. When phone will go to customer, FTD is not activated and
phone should not care of this. This will be a challenge to FTD application

During proper power off (use of power key or RE-CHARGE indication) some valuable data (e.g. the
number of current field test display) is stored onto the permanent memory. Next time when the phone
is powered on the lastly selected field test display will be automatically re-activated.

2.2 Activating the Field Test Displays

The Field Test Display is located in other folder and can be activated as follows:

1. Press application key

2. Scroll in the application list to other folder and from there field test display item
3. Press the Options button and Open or press rocker to select

The field test data display will then appear in a moment and first field test display is shown.
 SPECIFICATION 10 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

2.3 Deactivating the Field Test Displays

Test display can be deactivated by pressing Exit– key or

1. Press the Options button

2. Choose Exit

2.4 Field Test Display modes

2.4.1 Modes belonging in the use of the displays

There are tree Field Test Displays modes:

•Execute mode
• Data display mode
• Help mode

Different modes are marked in this specification as follows:

Execute mode: Data display mode:

************************** +++++++++++++++++++++++++++
* Execute display * + Parameter 1 aaaa +
* With this display it is * + Parameter 2 bbbb +
* possible to reset * + Parameter 3 cccc +
* registration / mobility * + Parameter 4 dddd +
* counters. Use options * + Parameter 5 eeee +
* to change. * + Parameter 6 ffff +
* * + Parameter 7 gggg +
* * + Pa 8 / Pa 9 hhhh iiii+
* * + Pa10 / Pa11 jjjj kkkk+
************************** +++++++++++++++++++++++++++
OPTIONS EXIT OPTIONS EXIT

The execute mode can be selected by choosing options from every execute display. Example, select
group 2 and display number 1, select options, select reset handover counters and confirm with Ok
button. Timers are reseted as soon as the OK button has been pressed from options menu and the
execute mode takes over.

During the data display mode, parameter text will define what parameter is visible, there is no help
mode so all needed information from that parameter is in that text field.

The rocker key (<,>^,v) offer an easy way to switch to another test displays without using the options
menu. Rocker (<,>) can be used to change different display groups, like Group1: GSM signaling
displays. Rocker (^,v) can be used to change different data displays from one group.

Display will support different colourcodes, all parameters which are in normal range are coloured with
green. When some parameter will go to critical level, example tx power is too low parameter is
coloured with red. NOTE Will be implmented if enough time to do that.
 SPECIFICATION 11 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Help mode: selection phase

+++++++++++++++++++++++++++
+ Parameter 1 aaaa +
+ Parameter 2 bbbb +
+ Parameter 3 cccc +
+ Parameter 4 dddd +
+ Parameter 5 eeee +
+ Parameter 6 ffff +
+ Parameter 7 gggg +
+ Pa 8 / Pa 9 hhhh iiii+
+ Pa10 / Pa11 jjjj kkkk+
+++++++++++++++++++++++++++
OPTIONS EXIT

It is possible to view help text from every parameter. By pressing

“copy-paste” button in Data mode, selection menu appears (highlight-
yellow) help text will appear by selecting parameter and by pressing
“rocker”. Help text’s are specified in description field for every
parameter.

Abbreviation Server Sub Block ID Mode Description (HELP TEXT)

bbb GSS FTD_SB_CARRIE R,I,O When mobile is on TCH: DCH carrier
R number of serving cell in decimal.
When mobile is NOT on TCH: CH means
carrier number of serving cell in decimal.
If hopping is on, used channels are
scrolled when display is updated

Help mode: help text phase, example

++++++++++++++++++++++++++++++
+ When mobile is on TCH: +
+ DCH carrier number of +
+ serving cell in decimal. +
+ When mobile is NOT on TCH: +
+ CH means carrier number +
+ of serving cell in decimal.+
+ If hopping is on, used +
+ channels are scrolled when +
+ display is updated. +
++++++++++++++++++++++++++++++
BACK

2.4.2 Modes belonging in the field test display data

The displayed data itself has three different modes:

• R = R&D Mode (allows all data presented on the display)

 SPECIFICATION 12 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

• O = Operator Mode (only network related displays presented on the display)

• I = Infra vendor mode (only network related and few R&D displays presented on the display)

The presented data are divided into displays so, that data with same mode are located in the own
displays. So, some displays can be activated/deactivated to be visible or not by the R&D people.

Signal and battery level

When Field Test Display is active, normal signal and battery level bars are visible.

3 INFORMATION ON THE DISPLAYS

Length of a field is shown in the display picture by amount of the letters. Two notations are currently
used. Examples of an old and new notations:

Old notation New notation

Field with 5 letters, field name aaaaa a(5)
a
Field with 4 letters, field name hhhh h(4)
h

If a value is not available, 'x' is shown for all the digits. If data to be displayed is shorter than the field
reserved to show that data, text is aligned left and numbers right.

In this specification the layouts of field test displays is drawn and all needed data items are shown in
each display. In the descriptive tables are mentioned the server, from which the data is got, the sub
block ID of the server message for the data, description of the data and the mode (R, I or O) for each
data item.

As so many field test display as possible are defined to be common. The rest of the displays are
divided based on protocol (GSM, TDMA, CDMA, PDC, WCDMA, TETRA). All displays are divided
into different groups based on that and in every group display numbering starts from 01.
 SPECIFICATION 13 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Format of the field is shown in Format column using next symbols:

Symbol Description
DW:D double word, 32bit value shown in decimal
DW:H double word, 32bit value shown in hexadecimal
W:D word, 16bit value shown in decimal
W:H word, 16bit value shown in hexadecimal
B:D byte, 8bit value shown in decimal
B:H byte, 8bit value shown in hexadecimal
S String
 SPECIFICATION 14 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 01: GSM Signaling displays, which can be visible to network operators

The network operators can activate these signaling displays. Before field test displays are visible,
mobile has to be modified. With the normal production mobile, field test displays are not working.

Display 01.01: Information of the serving cell (Version: 3.25, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Channel num abbb +
+ Rx level ccc +
+ Tx power lev ddd +
+ GPRS attach qq +
+ TS / TA e ff +
+ Rx / R time g mmmm +
+ C1 / C2 nnn ppp +
+ Band/ CHty rr oooo +
+ Amr U/AMR D x y +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a GSS FTD_SB_HOPPING R,I,O H, if carrier numbers are scrolled
when hopping is on. Otherwise '.'
bbb GSS FTD_SB_CARRIER R,I,O When mobile is on TCH: DCH carrier
number of serving cell in decimal.
When mobile is NOT on TCH: CH
means carrier number of serving cell
in decimal.
If hopping is on, used channels are
scrolled when display is updated
ERR means that mobile is out of
band.
ccc GSS FTD_SB_RX_LEVEL R,I,O Rx level in dBm, minus sign not
shown if <=-100
ddd GSS FTD_SB_TX_LEVEL R,I,O Tx power level. If transmitter is on,
symbol * is shown in front of the
power level value.
e GSS FTD_SB_TIME_SLOT R,I,O Time Slot, range is 0 – 7
ff GSS FTD_SB_TIMING_ADV R,I,O Timing advance, range is 0 - 63
g GSS FTD_SB_RX_QUALITY R,I,O Rx quality (sub), range is 0 - 7
mmmm GSS FTD_SB_RADIO_LINK_TIMEO R,I,O Radio Link Timeout value. If value is
UT negative, 0 is shown. Maximum value
is 64.
When mobile is NOT on TCH then xx
is show
nnn GSS FTD_SB_C1 R,I,O Value of the path loss criteria (C1).
Range is -99 - 999. ERR means that
the value is out of range, e.g.
because it was not able to be
calculated
 SPECIFICATION 15 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

ppp GSS FTD_SB_C2 R,I,O Value of the cell reselection criteria

(C2). Range is -99 - 999. If phone is
phase 1 then C1 value is shown. ERR
means that the value is out of range,
e.g. because it was not able to be
calculated.
rr GSS FTD_SB_CURR_BAND R,I,O Currently used band.Values:
9 = GSM900,
18 = GSM1800,
19 = GSM1900 ….. extensible for
future
oooo GSS FTD_SB_TYPE_OF_CURR_CH R,I,O Type of current channel
THR0: TCH HR subchannel 0
THR1: TCH HR subchannel 1
AHS0: TCH AHS subchannel 0
AHS1: TCH AHS subchannel 1
TFR: TCH FR
AFS: TCH AFS
TEFR: TCH EFR
F144: TCH FR data channel, speed
14.4 kbps
F96: TCH FR data channel, speed
9.6 kbps
F72: TCH FR data channel, speed
7.2 kbps
F48 : TCH FR data channel, speed
4.8 kbps
F24 : TCH FR data channel, speed
2.4 kbps
H480 : TCH HR data channel, speed
4.8 kbps, subch 0
H481 : TCH HR data channel, speed
4.8 kbps, subch 1
H240 : TCH HR data channel, speed
2.4 kbps, subch 0
H241 : TCH HR data channel, speed
2.4 kbps, subch 1
FA: TCH FR signaling only (FACCH)
channel
FAH0 : TCH HR signaling only
(FACCH) channel, subch 0
FAH1 : TCH HR signaling only
(FACCH) channel, subch 1
PCCC, PBCC, PAGC : GPRS packet
control channel
PNDR: GPRS non-DRX mode (in
PCCCH)
PDTC: GPRS traffic channel
NDRX: GPRS non-DRX mode (in
CCCH)
SDCC : SDCCH
AGCH : AGCH
CCCH : CCCH
CBCH : CCCH and cell broadcast
receiving on
BCCH : BCCH
SEAR : SEARCH
NSPS : MS is in No Serv Power Save
state
 SPECIFICATION 16 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

qq GPDS FTD_SB_GPDS_ATT_AND_PD R,I,O G if MS is GSM-GPRS attached,

P GP if attached and PDP context
created,
U if UMTS-GPRS attached,
UP if attached and PDP context
created,
otherwise empty.
x GSM_ FTD_SB_AMR_UL_MODE R,I,O Current absolute uplink mode on
DSP AMR channels, (0-7). 0=4.75, 1=5.15,
2=5.9, 3=6.7, 4=7.4, 5=7.95, 6=10.2,
7=12.2.
y GSM_ FTD_SB_AMR_DL_MODE R,I,O Current absolute downlink mode on
DSP AMR channels. See definition above.

Display 01.02: More information of the serving cell (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Paging mode aa +
+ max RACH retr b +
+ Roaming ind c +
+ BSIC value bdd +
+ CC cause ee +
+ Rx quality f +
+ CRO / Hopping ggg hh +
+ PenT / HCh iii j +
+ MAIO / HSN mm nn +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
aa GSS FTD_SB_PAGING_MODE R,I,O Paging mode
NO : normal paging
EX : extended paging
RO : paging reorganization
SB : same as before
b GSS FTD_SB_MAX_RAND_ACC R,I,O Maximum number of Random Access
_TRA retransmission
c GSS FTD_SB_ROAMING_IND R,I,O Roaming indicator, values are R or
empty.
bdd GSS FTD_SB_BSIC R,I,O Letter B and BSIC value, range is 0 -
63.
ee GSS FTD_SB_LAST_CALL_REL_ R,I,O Reason of last call release. Cause
REAS from messages disconnect and
release complete.
f GSS FTD_SB_ RX_QUALITY R,I,O RX quality (full), range is 0 – 7
ggg GSS FTD_SB_CELL_RESEL_OF R,I,O Cell reselect offset, range 0 - 126 dB.
FSET 0 - 63 * 2 dB. 'xxx' in active mode.
hh GSS FTD_SB_TEMP_OFFSET R,I,O Temporary offset, range 0 - 60 dB.
0 - 7 * 10 dB. 70 dB means infinite
time.
 SPECIFICATION 17 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

'xx' in active mode.

iii GSS FTD_SB_PENALTY_TIME R,I,O Penalty time, range 0 - 620 s.
0 - 31 * 20 s. 'xxx' in active mode
j GSS FTD_SB_HOPP_CH R,I,O Hopping channel
0 Single RF channel
1 RF hopping channel
mm GSS FTD_SB_MOB_ALLOC_IND R,I,O Mobile allocation index offset, MAIO
EX Range: 00 to 63 / xx when H=0
nn GSS FTD_SB_HSN R,I,O Hopping sequence number, HSN
Range: 00 to 63 / xx when H=0

Display 01.03: Information of the serving cell, 1st and 2nd neighbor (Version: 3.25, Status:
Approved)

Data Display:

+++++++++++++++++++++++++++
+ Serving cell info +
+ CH: C1: Rx: C2: +
+ aaa bbb ccc ddd +
+ 1. Neighbor info +
+ eee fff ggg hhh +
+ 2. Neighbor info +
+ iii jjj kkk lll +
+ 1. Neigbor ar mn +
+ 2. Neigbor ar op +
+++++++++++++++++++++++++++

1. row: serving cell information

2. row: 1. neighbor information
3. row: 2. neighbor information
4. row, mn: 1. neighbor information
4. row, op: 2. neighbor information

Abbr Server Sub Block ID Forma Mode Description

. t
aaa GSS FTD_SB_BCCH_CARRIER_ R,I,O Carrier number of serving cell in
SERV decimal
bbb GSS FTD_SB_C1S R,I,O C1 value of serving cell, range is -99 -
999, displayed only in idle mode. ERR
means that the value is out of range,
e.g. because it was not able to be
calculated.
Instead of C1 value, letter 'B' and BSIC
value will be displayed in active mode.
ccc GSS FTD_SB_RX_LEVEL R,I,O Rx level of serving cell in dBm, minus
sign not shown if <=-100
ddd GSS FTD_SB_C2S R,I,O C2 value of serving cell, range is -99 –
999. ERR means that the value is out
of range, e.g. because it was not able
to be calculated.
 SPECIFICATION 18 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

eee GSS FTD_SB_CARRIER_1_NEIG R,I,O Carrier number of 1. neighbor in

H decimal
fff GSS FTD_SB_C1_1_NEIGH R,I,O C1 of 1. neighbor value, range is -99 -
999, displayed only in idle mode. ERR
means that the value is out of range,
e.g. because it was not able to be
calculated.
Instead of C1 value, letter 'B' and BSIC
value will be displayed in active mode.
ggg GSS FTD_SB_RX_LEVEL_1_NEI R,I,O Rx level of 1. neighbor in dBm, minus
GH sign not shown if <=-100
hhh GSS FTD_SB_C2_1_NEIGH R,I,O C2 of 1. neighbor value, range is -99 –
999. ERR means that the value is out
of range, e.g. because it was not able
to be calculated.
iii GSS FTD_SB_CARRIER_2_NEIG R,I,O Carrier number of 2. neighbor in
H decimal
jjj GSS FTD_SB_C1_2_NEIGH R,I,O C1 value of 2. neighbor, range is -99 -
999, displayed only in idle mode. ERR
means that the value is out of range,
e.g. because it was not able to be
calculated.
Instead of C1 value, letter 'B' and BSIC
value will be displayed in active mode.
kkk GSS FTD_SB_RX_LEVEL_2_NEI R,I,O Rx level of 2. neighbor in dBm, minus
GH sign not shown if <=-100
lll GSS FTD_SB_C2_2_NEIGH R,I,O C2 value of 2. neighbor, range is -99 –
999. ERR means that the value is out
of range, e.g. because it was not able
to be calculated.
m GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden
_INFO_1 location area, otherwise location is
empty.
n GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L
1 is low priority, otherwise location is
empty.
o GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden
_INFO_2 location area, otherwise location is
empty.
p GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L
2 is low priority, otherwise location is
empty.

Display 01.04: Information of the 3rd, 4th and 5th neighbor (Version: 3.25, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ 3. Neighbor info +
+ aaa bbb ccc ddd +
+ 4. Neighbor info +
+ eee fff ggg hhh +
+ 5. Neighbor info +
+ iii jjj kkk lll +
+ 3. Neigbor ar mn +
 SPECIFICATION 19 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ 4. Neigbor ar op +
+ 5. Neigbor ar QR +
+++++++++++++++++++++++++++

1. row: 3. neighbor information

2. row: 4. neighbor information
3. row: 5. neighbor information
4. row, mn: 3. neighbor information
5. row, op: 4. neighbor information
6. row, qr: 5. neighbor information

Abbr Serve Sub Block ID Forma Mod Description

. r t e
aaa GSS FTD_SB_CARRIER_3_NEI R,I,O Carrier number of 3. neighbor in decimal
GH
bbb GSS FTD_SB_C1_3_NEIGH R,I,O C1 value of 3. neighbor, range is -99 - 999,
displayed only in idle mode. ERR means that
the value is out of range, e.g. because it was
not able to be calculated.
Instead of C1 value, letter 'B' and BSIC value
will be displayed in active mode.
ccc GSS FTD_SB_RX_LEVEL_3_NEI R,I,O Rx level of 3. neighbor in dBm, minus sign not
GH shown if <=-100
ddd GSS FTD_SB_C2_3_NEIGH R,I,O C2 value of 3. neighbor, range is -99 – 999.
ERR means that the value is out of range,
e.g. because it was not able to be calculated.
eee GSS FTD_SB_CARRIER_4_NEI R,I,O Carrier number of 4. neighbor in decimal
GH
fff GSS FTD_SB_C1_4_NEIGH R,I,O C1 value of 4. neighbor, range is -99 - 999,
displayed only in idle mode. ERR means that
the value is out of range, e.g. because it was
not able to be calculated.
Instead of C1 value, letter 'B' and BSIC value
will be displayed in active mode.
ggg GSS FTD_SB_RX_LEVEL_4_NEI R,I,O Rx level of 4. neighbor in dBm, minus sign not
GH shown if <=-100
hhh GSS FTD_SB_C2_4_NEIGH R,I,O C2 value of 4. neighbor, range is -99 – 999.
ERR means that the value is out of range,
e.g. because it was not able to be calculated.
iii GSS FTD_SB_CARRIER_5_NEI R,I,O Carrier number of 5. neighbor in decimal
GH
jjj GSS FTD_SB_C1_5_NEIGH R,I,O C1 value of 5. neighbor, range is -99 - 999,
displayed only in idle mode. ERR means that
the value is out of range, e.g. because it was
not able to be calculated.
Instead of C1 value, letter 'B' and BSIC value
will be displayed in active mode.
kkk GSS FTD_SB_RX_LEVEL_5_NEI R,I,O Rx level of 5. neighbor in dBm, minus sign not
GH shown if <=-100
lll GSS FTD_SB_C2_5_NEIGH R,I,O C2 value of 5. neighbor, range is -99 – 999.
ERR means that the value is out of range,
e.g. because it was not able to be calculated.
m GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden location
_INFO_3 area, otherwise location is empty.
n GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L is low
 SPECIFICATION 20 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

3 priority, otherwise location is empty.

o GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden location
_INFO_4 area, otherwise location is empty.
p GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L is low
4 priority, otherwise location is empty.
Q GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden location
_INFO_5 area, otherwise location is empty.
R GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L is low
5 priority, otherwise location is empty.

Display 01.05: Information of the 6th, 7th and 8th neighbor (Version: 3.25, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ 6. Neighbor info +
+ aaa bbb ccc ddd +
+ 7. Neighbor info +
+ eee fff ggg hhh +
+ 8. Neighbor info +
+ iii jjj kkk lll +
+ 6. Neigbor ar mn +
+ 7. Neigbor ar op +
+ 8. Neigbor ar qr +
+++++++++++++++++++++++++++

1. row: 6. neighbor information

2. row: 7. neighbor information
3. row: 8. neighbor information
4. row, ef: 6. neighbor information
5. row, gh: 7. neighbor information
6. row, ij: 8. neighbor information

Abbr Serve Sub Block ID Forma Mod Description

. r t e
aaa GSS FTD_SB_CARRIER_6_NEI R,I,O Carrier number of 6. neighbor in decimal
GH
bbb GSS FTD_SB_C1_6_NEIGH R,I,O C1 value of 6. neighbor, range is -99 - 999,
displayed only in idle mode. ERR means that
the value is out of range, e.g. because it was
not able to be calculated.
Instead of C1 value, letter 'B' and BSIC value
will be displayed in active mode.
ccc GSS FTD_SB_RX_LEVEL_6_NEI R,I,O Rx level of 6. neighbor in dBm, minus sign not
GH shown if <=-100
ddd GSS FTD_SB_C2_6_NEIGH R,I,O C2 value of 6. neighbor, range is -99 – 999.
ERR means that the value is out of range,
e.g. because it was not able to be calculated.
eee GSS FTD_SB_CARRIER_7_NEI R,I,O Carrier number of 7. neighbor in decimal
GH
fff GSS FTD_SB_C1_7_NEIGH R,I,O C1 value of 7. neighbor, range is -99 - 999,
displayed only in idle mode. ERR means that
 SPECIFICATION 21 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

the value is out of range, e.g. because it was

not able to be calculated.
Instead of C1 value, letter 'B' and BSIC value
will be displayed in active mode.
ggg GSS FTD_SB_RX_LEVEL_7_NEI R,I,O Rx level of 7. neighbor in dBm, minus sign not
GH shown if <=-100
hhh GSS FTD_SB_C2_7_NEIGH R,I,O C2 value of 7. neighbor, range is -99 – 999.
ERR means that the value is out of range,
e.g. because it was not able to be calculated.
iii GSS FTD_SB_CARRIER_8_NEI R,I,O Carrier number of 8. neighbor in decimal
GH
jjj GSS FTD_SB_C1_8_NEIGH R,I,O C1 value of 8. neighbor, range is -99 - 999,
displayed only in idle mode. ERR means that
the value is out of range, e.g. because it was
not able to be calculated.
Instead of C1 value, letter 'B' and BSIC value
will be displayed in active mode.
kkk GSS FTD_SB_RX_LEVEL_8_NEI R,I,O Rx level of 8. neighbor in dBm, minus sign not
GH shown if <=-100
lll GSS FTD_SB_C2_8_NEIGH R,I,O C2 value of 8. neighbor, range is -99 – 999.
ERR means that the value is out of range,
e.g. because it was not able to be calculated.
m GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden location
_INFO_6 area, otherwise location is empty.
n GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L is low
6 priority, otherwise location is empty.
o GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden location
_INFO_7 area, otherwise location is empty.
p GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L is low
7 priority, otherwise location is empty.
q GSS FTD_SB_LOCATION_AREA R,I,O F is shown if cell is in a forbidden location
_INFO_8 area, otherwise location is empty.
r GSS FTD_SB_CELL_PRIORITY_ R,I,O B is Barred, N is normal priority and L is low
8 priority, otherwise location is empty.

Display 01.06: Network selection display (Version: 1, Status: Approved)

This display shows the last registered network country code and network code as well as
the codes for four forbidden networks and the first 3 preferred networks.
Data Display:

+++++++++++++++++++++++++++
+ Last reg 1st forbidd +
+ aaaaaa eeeeee +
+ 1st pref 2nd forbidd +
+ bbbbbb ffffff +
+ 2nd pref 3rd forbidd +
+ cccccc gggggg +
+ 3rd pref 4th forbidd +
+ dddddd hhhhhh +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 22 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

1. row: last registered network - 1st forbidden network

2. row: 1st preferred network - 2nd forbidden network
3. row: 2nd preferred network - 3rd forbidden network
4. row: 3rd preferred network - 4th forbidden network

Abbr Serve Sub Block ID Forma Mode Description

. r t
a(6) GSS FTD_SB_LAST_REG R,I,O Last registred
network
b(6) GSS FTD_SB_1_PREF R,I,O 1. preferred network
c(6) GSS FTD_SB_2_PREF R,I,O 2. preferred network
d(6) GSS FTD_SB_3_PREF R,I,O 3. preferred network
st
e(6) GSS FTD_SB_1 _FORBIDDE R,I,O 1. forbidden PLMN in
N_NW SIM
nd
f(6) GSS FTD_SB_2 _FORBIDDE R,I,O 2. forbidden PLMN in
N_NW SIM
rd
g(6) GSS FTD_SB_3 _FORBIDDE R,I,O 3. forbidden PLMN in
N_NW SIM
th
h(6) GSS FTD_SB_4 _FORBIDDE R,I,O 4. forbidden PLMN in
N_NW SIM

Display 01.07: System information bits for serving cell (Version: 3.19, Status: Approved).

Data Display:

+++++++++++++++++++++++++++
+ Emergency cal a +
+ Attach detach b +
+ Half rate CH c +
+ C2 broadcast d +
+ SI 7&8 broad e +
+ Cell broad f +
+ Call Re-est g +
+ ECSC / 2-Ter h i +
+ Mband / GPRS j k +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block ID Forma Mod Description

r t e
a GSS FTD_SB_SYSTEM_INFO_ S R,I,O 1 is shown if emergency calls are supported,
BITS1 else 0
b GSS FTD_SB_SYSTEM_INFO_ S R,I,O 1 is shown if attach-detach-procedure is
BITS1 allowed, else 0
c GSS FTD_SB_SYSTEM_INFO_ S R,I,O 1 is shown if half rate channels are supported,
BITS1 else 0
d GSS FTD_SB_SYSTEM_INFO_ S R,I,O 1 is shown if C2 values are broadcast, else 0
BITS1
e GSS FTD_SB_SYSTEM_INFO_ S R,I,O 1 is shown if system information 7 and 8 are
 SPECIFICATION 23 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

BITS1 broadcast, else 0

f GSS FTD_SB_SYSTEM_INFO_ S R,I,O 1 is shown if cell broadcast is supported, else 0
BITS1
g GSS FTD_SB_SYSTEM_INFO_ S R,I,O 1 is shown if re-establishment is supported,
BITS1 else 0
h GSS FTD_SB_SYSTEM_INFO_ S R,I,O In idle mode 1 is shown if Early Classmark
BITS2 (ECSC) sending is supported, else 0. In
dedicated mode (conversation) X is shown.
i GSS FTD_SB_SYSTEM_INFO_ S R,I,O In idle mode 1 is shown if 2-Ter messages are
BITS2 supported, else 0.
In dedicated mode (conversation) X is shown.
j GSS FTD_SB_SYSTEM_INFO_ S R,I,O MultiBand reporting decimal value (0,1,2,3) is
BITS2 shown if supported. This is shown both in idle
and dedicated mode.
k GSS FTD_SB_GPRS_SUPPOR B:D R,I,O 1 is shown if GPRS is supported, else 0
T

The following is picked from Phase2+ ETSI GSM 05.08 version 5.4.0, Section 8.4.3 ""Additional cell
reporting requirements for multiband MS"".

For a multi band MS the number of cells, for each frequency band supported, which shall be included
in the measurement report is indicated by the parameter, MULTIBAND_REPORTING. The meaning
of different values of the parameter is specified as follows:

Value Meaning
0 (00) Normal reporting of the six strongest cells, with known and allowed NCC part of BSIC,
irrespective of the band used.
1 (01) The MS shall report the strongest cell, with known and allowed NCC part of BSIC, in each
of the frequency bands in the BA list, excluding the frequency band of the serving cell.
The remaining positions in the measurement report shall be used for reporting of cells in
the band of the serving cell. If there are still remaining positions, these shall be used to
report the next strongest identified cells in the other bands irrespective of the band used.
2 (10) The MS shall report the two strongest cells, with known and allowed NCC part of BSIC, in
each of the frequency bands in the BA list, excluding the frequency band of the serving
cell. The remaining positions in the measurement report shall be used for reporting of cells
in the band of the serving cell. If there are still remaining positions, these shall be used to
report the next strongest identified cells in the other bands irrespective of the band used.
3 (11) The MS shall report the three strongest cells, with known and allowed NCC part of BSIC,
in each of the frequency bands in the BA list, excluding the frequency band of the serving
cell. The remaining positions in the measurement report shall be used for reporting of cells
in the band of the serving cell. If there are still remaining positions, these shall be used to
report the next strongest identified cells in the other bands irrespective of the band used.

Display 01.08: Paging repeat period, TMSI, periodic location update, AFC and AGC (Version: 3.19,
Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ TMSI value aaaaaaaa +
 SPECIFICATION 24 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Curr T3212 bbb +

+ Initial T3212 ccc +
+ Paging repeat d +
+ Downlink fail ee +
+ TCH/SDCCH Ga ff +
+ VCTCXO AFC ggggg +
+ Channel num hhh +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
a(8) GSS FTD_SB_TMSI S R,I,O TMSI value in hex format
b(3) GSS FTD_SB_T3212 B:D R,I,O Current value of T3212 counter (range
is 000 - 'ccc', where 1 means 6 min
time. So, if this value is 2 less than
'ccc' then next periodic location
updating will be made within 2 * 6 min
= 12 minutes
c(3) GSS FTD_SB_T3212_TIMEOUT B:D R,I,O Timeout value of T3212 counter (range
is 000 - 240, where 1 means 6 min
time between location updates and
240 means 240 * 6 min = 24 h
between location updates. 000 means
that periodic location update is not in
use.) This value is received from the
network.
d GSS FTD_SB_PRP B:D R,I,O Value of paging repeat period (range is
2 - 9, when paging is in every second
multiframe, mobile takes more current
than if it were in every 9th multiframe)
e(2) GSS FTD_SB_DOWNLINK_SIGN B:D R,I,O Downlink signaling failure value. If
_FAIL value is negative, 0 is shown.
Maximum value is 45. When mobile is
on TCH then xx is shown
f(2) GSS FTD_SB_GAIN_ON_TCH B:D R,I,O Gain value on TCH/SDCCH, range is 0
- 93
g(5) GSS FTD_SB_VCTCXO_AFC_DA S R,I,O VCTCXO AFC DAC control, range is -
C 1024 - 1023
h(3) GSS FTD_SB_BCCH_CARRIER_ S R,I,O Serving cell channel number
SERV

Display 01.09: Network parameters (Version: 4.0, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Network parameters +
 SPECIFICATION 25 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Country code aaa +

+ Network code bbb +
+ Location area ccccc +
+ +
+ Serving cell +
+ Channel num ddd +
+ Cell +
+ identifier eeeeeeeeee +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
a(3) GSS FTD_SB_REG_MCC R,I,O MCC value in decimal (MCC=Mobile
Country Code)
b(3) GSS FTD_SB_REG_MNC R,I,O MNC value in decimal (MNC=Mobile
Network Code). Three digits are
shown only in DCS1900. In other
systems only two digits are shown.
c(5) GSS FTD_SB_LAC R,I,O LAC value in decimal (LAC=Location
Area Code)
d(3) GSS FTD_SB_BCCH_CARRIER_ R,I,O Serving cell channel number
SERV
e(10) GSS FTD_SB_CELL_ID DW:D R,I,O Cell Identifier in decimal format

LAC and CID may be in hex format in some projects. Or even both decimal and hexadecimal formats
may be shown on the same line.

Display 01.10: Ciphering, hopping DTX status and IMSI (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Updated only on TCH +
+ +
+ Cipherin val aaa +
+ +
+ Hopping val bbb +
+ +
+ DTX value ccc +
+ +
+ IMSI attach ddd +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Format Mode Description

aaa GSS FTD_SB_CIPH R,I,O Ciphering value, OFF/A51/A52
bbb GSS FTD_SB_HOPP_STATUS R,I,O Hopping value, ON/OFF
ccc GSS FTD_SB_DTX_VALUE R,I,O DTX value ON/OFF
ddd GSS FTD_SB_IMSI_ATT R,I,O IMSI attach
 SPECIFICATION 26 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

ON : IMSI attach on
OFF : IMSI attach off

These values are updated only on the TCH.

Display 01.11: Uplink DTX switching display (Version: 1, Status: Approved)

With this display it is possible to change MS to use DTX or not, if BS allows MS to decide it. This
display must be activated from MENU to change DTX state. When MENU is not active and the user is
scrolling field test displays with NEXT and PREVIOUS, the DTX state will not change.

Executive Display:

***************************
* Execute display *
* With this display it is *
* possible to change MS *
* to use DTX or not. Use *
* options to change *
* *
* DTX mode aaaaaaaaaa*
* Default DTX bbb *
* DTX from BS ccc *
***************************

Abbr Serve Sub Block ID Forma Mod Description

. r t e
EXE GSS FTD_SB_DTX_STATUS_CH N/A R,I,O Toggle DTX status.
ANGE
a(10) GSS FTD_SB_DTX_STATUS R,I,O Status of switched mode.
DTX:ON : MS uses DTX
DTX:OFF : MS does not use DTX
DTX:DEF : MS use default state of DTX.
Defined in MS_PAR.H
NOTALLOWED: BS does not allow MS to
decide if it uses DTX or not.

bbb GSS FTD_SB_DTX_DEF R,I,O Default state of DTX. Defined in MS_PAR.H.

The value is either ON or OFF
ccc GSS FTD_SB_DTX_FROM_BS R,I,O Is DTX value from BS
MAY : BS allows MS to decide if it uses dtx or
not on uplink.
USE : BS controls MS to use dtx (on uplink)
NOT : BS controls MS not to use dtx (on uplink)
 SPECIFICATION 27 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 01.12: Storing and removing BTS_TEST carrier (Version: 3.13, Status: Approved)

This display is used to change BTS_TEST carrier on permanent memory. If BTS_TEST carrier is
stored on permanent memory each time the mobile sends a search list it uses only the carrier number
stored on Mobile Station permanent memory. Also the neighbor information from system information
messages is ignored. If the BTS_TEST carrier is not stored, then the mobile behaves normally (i.e.
does the neighbor measurements according the GSM specifications).

Executive Displays:

***************************
* Execute display *
* With this display it is *
* possible to change *
* BTS_TEST carrier. Use *
* options to change *
* *
* BTS TEST locked on *
* channel xxxx *
* *
***************************

Mobile is searching only one frequency. Neighbor measurements are not done.

***************************
* Execute display *
* With this display it is *
* possible to change *
* BTS_TEST carrier. Use *
* options to change *
* *
* BTS TEST OFF *
* *
* *
***************************

Mobile is behaving normally. Neighbor measurements are done.

To store BTS test carrier, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 0112 (TEST GROUP;TEST DISPLAY) to the query
prompt.
5. Test input promt will be shown on the display, enter the channel number in display.
 SPECIFICATION 28 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

6. Confirm with the Ok button.

7. Switch power off and on.
8. If activation succeeded, there is text "BTS TEST LOCKED, CH:…" in display 12 of group 1.

To deactivate BTS tests, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 0112 (TEST GROUP;TEST DISPLAY) to the query
prompt.
5. Test input promt will be shown on the display, enter the 3333 as a channel number in display
6. Confirm with the Ok button.
7. Switch power off and on.
8. If deactivation succeeded, there is text "BTS TEST OFF" in display 12 of group 1.

The legal carrier numbers:

Band Carrier Numbers

GSM450 259-293
GSM480 306-340
GSM 850 128-251
GSM900 1-124
GSM1800 512-885
GSM1900 512-810
E-GSM 0, 975 – 1023
R-GSM 955-974

Abbr. Server Sub Block ID Forma Mod Description

t e
xxxx NETWOR FTD_SB_BTS_STA R,I,O BTS test
K TUS status
INPUT NETWOR FTD_SB_BTS_TES DW:D R,I,O BTS test
K T

Display 01.13: Toggle Cell Barred Status (Version: 1, Status: Approved)

Executive Displays:

***************************
* Execute display *
* With this display it is *
* possible to change *
* Call bearer status.Use *
* options to change *
* *
* CALL BEARER *
* xxxxxxxx *
 SPECIFICATION 29 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

* *
***************************

This test is meant to be used when some cells are tested prior taking them into commercial
use. By setting the barring on in the base station normal GSM phones will not try to register
these barred cells. By selecting cell barring reversed, the MS will only use the cells to be
tested. However, if at the same time it is wanted that MS will be capable to use normal
network cell barring ignored can be set. This display will show the cell barring mode.

NOTE! If a cell has been selected before barring state is changed the selected cell may have different
barring state than what the display shows. After reselection the cell barring state is working for sure.

To change Cell Barring status, perform following steps:

1. Press the Menu button.

2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in executive mode by entering 0113 (TEST GROUP;TEST DISPLAY) to the
query prompt.
5. Confirm with the Ok button.
6. If activation succeeded, there is text "CELL BARR …" in display 13 of group 1.

Abbr. Server Sub Block ID Forma Mode Description

t
Cell barr GSS FTD_SB_CELL_BARR_IND_STATUS_ R,I,O Toggle Cell Barring
exe CHANGE status
Cell barr GSS FTD_SB_CELL_BARR_STATUS_IND R,I,O Cell Barring status
stat

Display 01.14: Modify "last used band" (Version: 1, Status: Approved)

This display is applicable only in phones having both European and American frequencies.

With this display it is possible to manipulate the "last used band". In multi-band products this
paramater is used at startup to decide which band shall be searched first. In most cases the last used
band is the most promising band to find networks in. Nevertheless, for testing purposes it is helpful to
have influence on this decision.
If at startup no "last used band" is found in the memory, the "Default" setting (Europe or America)
will be effective.

Executive Display:

***************************
* Execute display *
* With this display it is *
 SPECIFICATION 30 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

* possible to set band *

* which will be searched *
* first after startup *
* *
* Use options to set. *
* *
* *
***************************

1. Press the Menu button.

2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 01.14 (TEST GROUP;TEST DISPLAY) to the query
prompt.
5. Test input prompt will activate, enter the desired band code (see the table below) in display.
6. Confirm with the Ok button.
7. REMOVE BATTERY or POWER SUPPLY

NOTE: In normal operation the last used band is saved to the memory at power-down. If this value is
written via Test Display 01.14, the phone MUST NOT be powerd off normally afterwards, because
then the user-set value will be overwritten. The power supply has be interrupted instead.

Abbr. Server Sub Block ID Forma Mod Description

t e
a(2) GSS FTD_SB_LAST_USED_BAND_ B:D R,I,O Last used band, see the table
READ below
INPUT GSS FTD_SB_LAST_USED_BAND_ DW:D R,I,O Write value to memory
SET

Band codes:

Band Code Meaning

9 GSM900
18 GSM1800
19 GSM1900
Other Delete stored value
 SPECIFICATION 31 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 02: GSM Registration and Mobility Displays

Display 02.01: Reset Registration and Mobility counters (Version: 1, Status: Approved)

With this display all timers listed on the displays in this group can be reset.

Executive Display:

***************************
* Execute display *
* With this display it is *
* possible to reset *
* registration / mobility *
* counters. Displays *
* 02/02 – 02/07 *
* Use options to change. *
* *
* *
***************************

Abbr. Server Sub Block ID Form Mode Description

at
EXE GSS FTD_SB_RESET_HANDOVE N/A R Reset handover
RS counters.

Display 02.02: Neighbor Measurement Counter Display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Neighbor counter display+
+ PSW meas +
+ attempts aaaa +
+ Sync meas +
+ attempts bbbb +
+ BCCH meas +
+ attempts cccc +
+ BCCH meas +
+ ext att dddd +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa GSS FTD_SB_NEIGH_PS R Counter for neighbor PSW measurement
W_ATT attempts
bbbb GSS FTD_SB_NEIGH_SYN R Counter for neighbor synchronization
C_ATT measurement attempts
 SPECIFICATION 32 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

cccc GSS FTD_SB_NEIGH_BC R Counter for neighbor BCCH measurement

CH_ATT attempts
dddd GSS FTD_SB_BCCH_EXT R Counter for neighbor BCCH Ext measurement
_ATT attempts

Counter values are shown in hexadecimal form. On poweroff the values of the counter displays are
stored onto the permanent memory, where they will be read during power on. To initialize the counters
to zero, select Display 02.01: Reset Registration and Mobility counters. Counters are automatically
reset to zero when they exceed their maximum value.

Display 02.03: Search and reselection counter display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Search/reselect counters+
+ GSM 900 PSW aaaaa +
+ GSM 1800 PSW bbbbb +
+ GSM 900 sync ccccc +
+ GSM 1800 sync ddddd +
+ 900-900 res eeeee +
+ 1800-1800 res fffff +
+ 900-1800 res ggggg +
+ 1800-900 res hhhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaaa GSS FTD_SB_NO_PSW_FO R GSM900 counter for MDI_NO_PSW_FOUND
UND_GSM message received from DSP in decimal form
(max 99999).
bbbbb GSS FTD_SB_NO_PSW_FO R GSM1800 counter for MDI_NO_PSW_FOUND
UND_DCS message received from DSP in decimal form
(max 99999).
ccccc GSS FTD_SB_SYNC_GSM R GSM900 counter for synchronization
measurement attempts in decimal form. If
counter value is over 99999 then five x are
shown.
ddddd GSS FTD_SB_SYNC_DCS R GSM1800 counter for synchronization
measurement attempts in decimal form. If
counter value is over 99999 then five x are
shown.
eeeee GSS FTD_SB_RESEL_GSM R Counter for GSM900->GSM900 cell
_GSM reselections in decimal form (max 99999).
fffff GSS FTD_SB_RESEL_DCS R Counter for GSM1800->GSM1800 cell
_DCS reselections in decimal form (max 99999).
ggggg GSS FTD_SB_RESEL_GSM R Counter for GSM900->GSM1800 cell
_DCS reselections in decimal form (max 99999).
hhhhh GSS FTD_SB_RESEL_DCS R Counter for GSM1800->GSM900 cell
_GSM reselections in decimal form (max 99999).
 SPECIFICATION 33 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

On power off the values of the counter displays are stored onto the permanent memory, where they
will be read during power on. To initialize the counters to zero, select Display 02.01: Reset
Registration and Mobility counters. Counters are automatically reset to zero when they exceed their
maximum value.

Display 02.04: Location update attempts counters (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Location update counters+
+ Fail reasons: +
+ Norm LU Aa +
+ Periodic&IMSI dd +
+ Counters: +
+ Norm LU total bbb +
+ Norm LU ok ccc +
+ Periodic tot eee +
+ periodic ok fff +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
Aa GSS FTD_SB_LAST_NORM R Reason of last normal location update failure
AL_LOC_UP_REASON
bbb GSS FTD_SB_NORMAL_LO R Count of normal location update attempts
C_UP_COUNT
ccc GSS FTD_SB_SUCC_LOC_ R Count of succeeded normal location updates
UP_COUNT
dd GSS FTD_SB_LAST_IMSI_A R Reason of last periodic or IMSI attach location
TT_FAIL_REASON update failure
eee GSS FTD_SB_LOC_UP_CO R Count of all periodic and IMSI attach location update
UNT_IMSI attempts
fff GSS FTD_SB_SUCC_LOC_ R Count of succeeded periodic and IMSI attach
UP_COUNT_IMSI location updates

On poweroff the values of the counter displays are stored onto the permanent memory, where they will
be read during power on. To initialize the counters to zero, select Display 02.01: Reset Registration
and Mobility counters. Counters are automatically reset to zero when they exceed their maximum
value.

Display 02.05: Handover display, INTER CELL (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ INTER CELL Handovers +
+ 900->900 OK aaaa +
+ 1800->1800 OK bbbb +
+ 900->1800 OK cccc +
 SPECIFICATION 34 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ 1800->900 OK dddd +
+ 9-9/18-18FAIL eee fff +
+ 9-18/18-9FAIL ggg hhh +
+ 9-9/18-18prev iii jjj +
+ 9-18/18-9prev kkk lll +
+++++++++++++++++++++++++++

Abbr Serve Sub Block ID Forma Mod Description

. r t e
aaaa GSS FTD_SB_HO_GSM_GSM R Counter of successful handovers (max
9999) from GSM900 to GSM900
bbbb GSS FTD_SB_HO_DCS_DCS R Counter of successful handovers (max
9999) from GSM1800 to GSM1800
cccc GSS FTD_SB_HO_GSM_DCS R Counter of successful handovers (max
9999) from GSM900 to GSM1800
dddd GSS FTD_SB_HO_DCS_GSM R Counter of successful handovers (max
9999) from GSM1800 to GSM900
eee GSS FTD_SB_FAILED_HO_GSM_G R Counter for failed handovers (max 999)
SM from GSM900 to GSM900
fff GSS FTD_SB_FAILED_HO_DCS_D R Counter for failed handovers (max 999)
CS from GSM1800 to GSM1800
ggg GSS FTD_SB_FAILE_HO_GSM_DC R Counter for failed handovers (max 999)
S from GSM900 to GSM1800
hhh GSS FTD_SB_FAILED_HO_DCS_G R Counter for failed handovers (max 999)
SM from GSM1800 to GSM900
iii GSS FTD_SB_BACK_TO_PREV_GS R Counter of successful back to previous
M_GSM channel attempts (max 999) from
GSM900 to GSM900
jjj GSS FTD_SB_BACK_TO_PREV_DC R Counter of successful back to previous
S_DCS channel attempts (max 999) from
GSM1800 to GSM1800
kkk GSS FTD_SB_BACK_TO_PREV_GS R Counter of successful back to previous
M_DCS channel attempts (max 999)from
GSM900 to GSM1800
lll GSS FTD_SB_BACK_TO_PREV_DC R Counter of successful back to previous
S_GSM channel attempts (max 999) from
GSM1800 to GSM900

Counters will stop when they reach their maximum. To initialize the counters to zero Display 02.01:
Reset Registration and Mobility counters.

Display 02.06: Handover display, INTRA CELL (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ INTRA CELL Handovers +
+ 900->900 OK aaaa +
+ 1800->1800 OK bbbb +
+ 900->1800 OK cccc +
+ 1800->900 OK dddd +
+ 9-9/18-18FAIL eee fff +
+ 9-18/18-9FAIL ggg hhh +
 SPECIFICATION 35 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ 9-9/18-18prev iii jjj +

+ 9-18/18-9prev kkk lll +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa GSS FTD_SB_INTRA_HO_ R Counter of successful INTRA CELL handovers
GSM_GSM (max 9999) from GSM900 to GSM900
bbbb GSS FTD_SB_INTRA_HO_ R Counter of successful INTRA CELL handovers
DCS_DCS (max 9999) from GSM1800 to GSM1800
cccc GSS FTD_SB_INTRA_HO_ R Counter of successful INTRA CELL handovers
GSM_DCS (max 9999) from GSM900 to GSM1800
dddd GSS FTD_SB_INTRA_HO_ R Counter of successful INTRA CELL handovers
DCS_GSM (max 9999) from GSM1800 to GSM900
eee GSS FTD_SB_FAILED_INT R Counter of failed INTRA CELL handovers (max
RA_HO_GSM_GSM 999) from GSM900 to GSM900
fff GSS FTD_SB_FAILED_INT R Counter of failed INTRA CELL handovers (max
RA_HO_DCS_DCS 999) from GSM1800 to GSM1800
ggg GSS FTD_SB_FAILED_INT R Counter of failed INTRA CELL handovers (max
RA_HO_GSM_DCS 999) from GSM900 to GSM1800
hhh GSS FTD_SB_FAILED_INT R Counter of failed INTRA CELL handovers (max
RA_HO_DCS_GSM 999) from GSM1800 to GSM900
iii GSS FTD_SB_INTRA_BAC R Counter of successful back to previous normal
K_TO_PREV_GSM_G INTRA CELL channel attempts (max 999) from
SM GSM900 to GSM900
jjj GSS FTD_SB_INTRA_BAC R Counter of successful back to previous normal
K_TO_PREV_DCS_D INTRA CELL channel attempts (max 999) from
CS GSM1800 to GSM1800
kkk GSS FTD_SB_INTRA_BAC R Counter of successful back to previous normal
K_TO_PREV_GSM_D INTRA CELL channel attempts (max 999) from
CS GSM900 to GSM1800
lll GSS FTD_SB_INTRA_BAC R Counter of successful back to previous normal
K_TO_PREV_DCS_G INTRA CELL channel attempts (max 999) from
SM GSM1800 to GSM900

Counters will stop when they reach their maximum. To initialize the counters to zero, select Display
02.01: Reset Registration and Mobility counters.

Display 02.07: L2 display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ L2 retransmission +
+ T200 MS 900 aaaa +
+ +
+ T200 BS 900 bbbb +
+ +
+ T200 MS 1800 cccc +
+ +
+ T200 BS 1800 dddd +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 36 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
aaaa GSS FTD_SB_T200_EXP_ R GSM900: Counts how many times T200 in MS
MS_GSM has expired and therefore L2 transmission has
been repeated.
bbbb GSS FTD_SB_T200_EXP_B R GSM900: Counts how many times T200 in BS
S_GSM (network) has expired and therefore L2
transmission has been repeated
cccc GSS FTD_SB_T200_EXP_ R GSM1800: Counts how many times T200 in MS
MS_DCS has expired and therefore L2 transmission has
been repeated (for dualband phones).
dddd GSS FTD_SB_T200_EXP_B R GSM1800: Counts how many times T200 in BS
S_DCS (network) has expired and therefore L2
transmission has been repeated (for dualband
phones)

Counters will stop when they reach their maximum. To initialize the counters to zero Display 02.01:
Reset Registration and Mobility counters.
 SPECIFICATION 37 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 03: GSM memory handling

Display 03.01: SIM information 1 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ SIM information 1 +
+ +
+ SIM voltage aaaaa +
+ SIM baudrate bbb +
+ Clk stop allo c +
+ Clk stop cond dddddddd +
+ Pin1/Pin2 att f g +
+ Puk1/Puk2 att hh ii +
+ ATR retrans j +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(5) SIM FTD_SB_SIM_VOL_SEL S R Sim voltage selection type (3, 1V8
or 1V8/3)
b(3) SIM FTD_SB_SIM_BAUDRAT W:D R Sim baudrate (372, 64, 32 or 0)
E
c SIM FTD_SB_CLOCK_STOP_ S R Clock stop allowed, Y or N
ALL
d(8) SIM FTD_SB_CLOCK_STOP_ S R Clock stop condition, High or low
COND (preferred)
f SIM FTD_SB_PIN1_ATT B:D R Pin1 attempts left (0,1,2,3)
g SIM FTD_SB_PIN2_ATT B:D R Pin2 attempts left (0,1,2,3)
hh SIM FTD_SB_PUK1_ATT B:D R Puk1 attempts left (0-10)
ii SIM FTD_SB_PUK2_ATT B:D R Puk2 attempts left (0-10)
j SIM FTD_SB_ATR_RETRANS B:D R ATR retransmission counter (0-9)

Display 03.02: SIM information 2 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ SIM information 2 +
+ Service table +
+ from 6F38 aaaaaaaaaa+
+ Customer serv +
+ profile 6F15 bbbbbbbbbb+
+ Customer serv +
+ profile 6F98 cccccccccc+
+ ATR historic +
+ bytes dddddddddd+
 SPECIFICATION 38 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(10) SIM FTD_SB_SIM_SERV_TA R The service table form the sim card file 6F38.
B The readout of the service table is
compressed so that each service is
reprecented with one bit. 1 for Allocated
Activated otherwise 0.
b(10) SIM FTD_SB_SIM_CSP1 R The Customer service profile from file 6F15
on binary form.
c(10) SIM FTD_SB_SIM_CSP2 R The Customer service profile from file 6F98
on binary form
d(10) SIM FTD_SB_SIM_HIST_DAT R Max. first 5 historical bytes from the ATR on
A binary form.
 SPECIFICATION 39 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 04: GSM Test Timers, SMS and Call Counter Displays

Display 04.01: Reset test timers to zero and restart them (Version: 1, Status: Approved)

With this display all timers listed on the Display 04.02. can be reset.

Executive Display:

***************************
* Execute display *
* With this display it is *
* possible to reset *
* test timers to zero. *
* Display 04/03. *
* Use options to change. *
* *
* *
* *
***************************

Abbr. Server Sub Block ID Forma Mode Description

t
EXE GSS FTD_SB_RESET_TEST_TIMERS N/A R Reset and restart Test timers

Display 04.02: Enable or disable test timers (Version: 1, Status: Approved)

This display will only use to start or stop the timers. When looking the status of timers user
should use the Display 04.03: Test timer display (Version: 1, Status: Approved)

Executive Display:

***************************
* Execute display *
* With this display it is *
* possible to start and *
* stop test timers *
* Display 04/03. *
* Use options to change. *
* *
* *
* XXX *
* *
***************************

XXX ON or OFF
 SPECIFICATION 40 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

On power off the values of the timer displays are stored onto the permanent memory, where they will
be read during power on. To initialize the counters to zero, use Display 04.01: Reset test timers to
zero and restart them.

Also the current state of timer disabling/enabling is stored onto the permanent memory.

Abbr. Server Sub Block ID Form Mode Description

at
EXE GSS FTD_SB_ENAB_OR_DISAB_TEST_TIME N/A R Enable / DisableTimers
RS
b(6) GSS FTD_SB_TEST_TIMER_STATE R State of timers,
ON/OFF

Display 04.03: Test timer display (Version: 1, Status: Approved)

Data Display:
+++++++++++++++++++++++++++
+ Test timer display +
+ +
+ Power on time aaaa +
+ Service time bbbb +
+ No-serv time cccc +
+ Trans on time dddd +
+ Timers state eee +
+ +
+ +
+++++++++++++++++++++++++++

A Server Sub Block ID Form Mode Description

at
aaaa GSS FTD_SB_POWER_ON_TI R Timer for how long the phone has been
MER powered on
bbbb GSS FTD_SB_SERV_TIMER R Timer for how long the phone has been in
service
cccc GSS FTD_SB_NSPS_TIMER R Timer for NO-SERV POWER-SAVE state
dddd GSS FTD_SB_TRANSMIT_TIM R Timer for how long the transmitter has been
ER on
eee GSS FTD_SB_TEST_TIMER_S R State of timers, ON/OFF
TATE

All the values are shown in one minute resolution. The accuracy of the timers is about one second.
The display uses following format for timers: HHMM where HH is hours and MM is minutes.

NOTE: When the maximum usage time of the phone is required (e.g. idle time measurement) then
ALL field test displays must be deactivated! See chapter Errore. L'origine riferimento non è stata
trovata. Errore. L'origine riferimento non è stata trovata., how to deactivate the field test displays.
 SPECIFICATION 41 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 04.04: Reset SMS and Call Counters to zero (Version: 1, Status: Approved)

With this display all counters listed on the Display 04.05: Call attempts counters (Version: 1,
Status: Approved),

Display 04.07: SMS attempts counters and Display 04.08: SMS timeout counters can be reset.

Executive Display:

***************************
* Execute display *
* With this display it is *
* possible to reset *
* SMS and Call counters *
* to zero. Displays 04/05 *
* 05/07, 04/08 *
* Use options to change *
* *
* *
* *
***************************

Abbr. Server Sub Block ID Format Mode Description

EXE GSS FTD_SB_RESET_T N/A R Reset SMS & Call counter
EST_COUNTERS displays

Display 04.05: Call attempts counters (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Call attempts counters +
+ +
+ CC cause Aa +
+ Release dire bb +
+ MO attempts ccc +
+ MO call ok ddd +
+ MT attempts eee +
+ MT call ok fff +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
Aa GSS FTD_SB_LAST_CALL R Reason of last call release: Cause from
 SPECIFICATION 42 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

_REL_REAS messages disconnect and release complete

bb GSS FTD_SB_LAST_CALL R Direction of last call release:
_REL_DIRECTION UN : Unknown
MO : Mobile originated
MT : Mobile terminated
IN : Internal (ME CS sw)
ccc GSS FTD_SB_MO_CALL_ R Count of all MO call attempts made
COUNT
ddd GSS FTD_SB_MO_CALL_ R Count of succeeded MO calls
OK_COUNT
eee GSS FTD_SB_MT_CALL_C R Count of all call setups received
OUNT
fff GSS FTD_SB_MT_CALL_ R Count of succeeded MT calls
OK_COUNT

On poweroff the values of the counter displays are stored onto the permanent memory, where they will
be read during power on. To initialize the counters to zero, select Display 04.04: Reset SMS and Call
Counters to zero. Counters are automatically reset to zero when they exceed their maximum value.

Display 04.06: Information about reasons for call clearing (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Information from call +
+ clearing reasons +
+ +
+ CC cause aaaa +
+ +
+ MM cause bbbb +
+ +
+ RR cause cccc +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa GSS FTD_SB_CC_CAUS R CC cause value, see section 10.5.4.11/GSM
E 04.08. '*' is shown in front of cause value if cause
is made up by CC layer in MS
bbbb GSS FTD_SB_MM_CAUS R MM cause value, see section 10.5.3.6/GSM 04.08.
E '*' is shown in front of cause value if cause is
made up by MM layer in MS
cccc GSS FTD_SB_RR_CAUS R RR cause value, see section 10.5.2.31/GSM
E 04.08. '*' is shown in front of cause value if cause
is made up by RR layer in MS

All cause values are shown in decimal form.

 SPECIFICATION 43 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 04.07: SMS attempts counters (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ SMS attempts counters +
+ Last MO fail aa +
+ MO all bbb +
+ MO Ok ccc +
+ Last MT fail dd +
+ MT all eee +
+ MT Ok fff +
+ Broad sche gggg +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
aa GSS FTD_SB_LAST_MO_SMS_F R Reason of last sending failure
AIL
bbb GSS FTD_SB_MO_SMS_COUNT R Count of all MO short message
attempts
ccc GSS FTD_SB_MO_SMS_OK_CO R Count of succeeded MO short
UNT message attempts
dd GSS FTD_SB_LAST_MT_SMS_F R Reason of last receiving failure
AIL
eee GSS FTD_SB_MT_SMS_COUNT R Count of all MT short message
attempts
fff GSS FTD_SB_MT_SMS_OK_CO R Count of succeeded MT short
UNT message attempts
gggg GSS FTD_SB_CB_SCHEDULE_ R Count of all received cell broadcast
MSG schedule messages
On poweroff the values of the counter displays are stored onto the permanent memory, where they will
be read during power on. To initialize the counters to zero Display 04.04: Reset SMS and Call
Counters to zero. Counters are automatically reset to zero when they exceed their maximum value.

Display 04.08: SMS timeout counters (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ SMS timeout counters +
+ +
+ TR1M aaa +
+ TR2M bbb +
+ TRAM cc +
 SPECIFICATION 44 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ TC1M ddd +
+ TC2M eee +
+ CB schedule ff +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
aaa GSS FTD_SB_TR1M_COUNT R Counter for TR1M timeouts
bbb GSS FTD_SB_TR2M_COUNT R Counter for TR2M timeouts
cc GSS FTD_SB_TRAM_COUNT R Counter for TRAM timeouts
ddd GSS FTD_SB_TC1M_COUNT R Counter for TC1M timeouts
eee GSS FTD_SB_TC2M_COUNT R Counter for TC2M timeouts
ff GSS FTD_SB_CB_SCHEDULE_C R Counter for CB schedule timeouts
OUNT
On poweroff the values of the counter displays are stored onto the permanent memory, where they will
be read during power on. To initialize the counters to zero, select Display 04.04: Reset SMS and Call
Counters to zero. Counters are automatically reset to zero when they exceed their maximum value.

Display 04.09: Toggle transmitter functionality (Version: 1, Status: Approved)

When selected, disables transmitter functionality if enabled and vice versa. New setting is
valid until next power off or until new execute of this display.

Executive Display:

***************************
* Execute display *
* With this display it is *
* possible to disable *
* or enable transmitter *
* Use options to change. *
* *
* xxxxxxxx *
* *
* *
***************************
Options
Enabled or disabled

This FTD can be used to simulate easily situations when the MS can hear the network (i.e. receiving
signal is good enough), but the network can not receive any messages from the MS.

Location updating attempts or MO call establishment attempts can be failed (random access failure) by
this FTD and field testing of these failures is much easier now.

Next periodic location updating can be checked from the Display 01.08: Paging repeat
period, TMSI, periodic location update, AFC and AGC (Version: 3.19, Status: Approved) by
taking the difference of current T3212 counter value and T3212 timeout value.
 SPECIFICATION 45 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
aaaaaaaa GSS FTD_SB_TOGGLE_TRANS_STATUS R Transmitter status
EXE GSS FTD_SB_TOGGLE_TRANS_STATUS N/A R Toggle transmitter
_CHANGE functionality
 SPECIFICATION 46 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 05: GSM Data Displays

Display 05.01: HSCSD, Timeslot information display (Version: 3.19, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ HSCSD Timeslot +
+ information display +
+ +
+ Timeslot 01234567 +
+ RX rrrrrrrr +
+ TX tttttttt +
+ Main CH Ts x +
+ Main CH power yy +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
rrrrrrrr GSS FTD_SB_RX_TIMESL R,I,O Each bit can have value 1 or 0, 1 indicating that
OT_ALLOC timeslot is part of multislot allocation in downlink
direction.
tttttttt GSS FTD_SB_TX_TIMESL R,I,O Each bit can have value 1 or 0, 1 indicating that
OT_ALLOC timeslot is part of multislot allocation in uplink
direction.
x GSS FTD_SB_MAIN_CH_P R,I,O Value from 0 to 7 indicating the place of main
LACE channel. In case of GPRS multislot allocation,
this is not valid "x".
yy GSS FTD_SB_MAIN_CH_P R,I,O Value from 0-31 indicating main channel power
WR_CONTROL control level. In case of GPRS multislot
allocation, this is not valid "xx".

Display 05.02: HSCSD, Timeslot power control level display (Version: 3.19, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Main CH TS x +
+ Main CH power yy +
+ Pwr level TS0 aa +
+ Pwr level TS1 bb +
+ Pwr level TS2 cc +
+ Pwr level TS3 dd +
+ Pwr level TS4 ee +
+ Pwr level TS5 ff +
+ Pwr TS6 / TS7 gg hh +
+++++++++++++++++++++++++++
 SPECIFICATION 47 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
x GSS FTD_SB_MAIN_CH_P R,I,O Value from 0 to 7 indicating the place of main
LACE channel. In case of GPRS multislot allocation,
this is not valid "x".
yy GSS FTD_SB_MAIN_CH_P R,I,O Value from 0-31 indicating main channel power
WR_CONTROL control level. In case of GPRS multislot
allocation, this is not valid "xx".
aa GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 0.
ROL_TS_0
bb GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 1.
ROL_TS_1
cc GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 2.
ROL_TS_2
dd GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 3.
ROL_TS_3
ee GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 4.
ROL_TS_4
ff GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 5.
ROL_TS_5
gg GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 6.
ROL_TS_6
hh GSS FTD_SB_PWR_CONT R,I,O Power control level for timeslot 7.
ROL_TS_7

Display 05.03: Transparent data information (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Transparent data info +
+ Num of CH's Aaa +
+ Connect speed Bbbb +
+ Connect type cccc +
+ Connect mode dddd +
+ Mode status eee +
+ SB stat bit fff +
+ X stat bit gg +
+ V.80 hhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
Aaa CSD FTD_SB_TB_NUM_CHAN R Number of channels. Value 1+1 or 2+2.
Applicable only in GSM mode,
otherwise show xxx.
Bbbb CSD FTD_SB_TB_CON_SPEED R Connection speed in kbit/s.
2.4 : 2400 bit/s
4.8 : 4800 bit/s
9.6 : 9600 bit/s
14.4 : 14400 bit/s
 SPECIFICATION 48 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

19.2 : 19200 bit/s

28.8 : 28800 bit/s
32: 32000 bits/s
33.6: 33600 bits/s
56: 56000 bits/s
64: 64000 bits/s
cccc CSD FTD_SB_TB_CON_TYPE R Connection type.
Asyn :When connection is
asynchronous
Syn :When connection is synchronous
dddd CSD FTD_SB_TB_CON_MODE R Connection mode.
Buff : Connection is in buffered mode
V.80 : Connection is in V.80 mode
eee CSD FTD_SB_TB_STATUS_CON_ R Status of connection mode.
MODE SCN : When synchronizing
CON : When connected
Applicable only in GSM mode,
otherwise show xxx.
fff CSD FTD_SB_TB_STATUS_SB R Status bit SB value 0 or 1.
SB0: Status ON
SB1: Status OFF
Applicable only in GSM mode,
otherwise show xxx.
gg CSD FTD_SB_TB_STATUS_X R Status bit X value 0 or 1.
X0 : Status ON
X1 : Status OFF
Applicable only in GSM mode,
otherwise show xx.
hhhh CSD FTD_SB_TB_V80_SM R When V.80 is used the sub mode is
shown.
Tran : Transparent
Fram : Framed

Display 05.04: Non transparent data (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Non Transparent data +
+ +
+ Sent I-farmes aaaaaaaa +
+ X-bit out bb +
+ Re-trans cccccccc +
+ Uplink buff dd +
+ Received I-fr eeeeeeee +
+ X-bit in ff +
+ SREJ frames gggggggg +
+ Downlink buff hh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
 SPECIFICATION 49 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

aaaaaaaa CSD FTD_SB_NTB_ R Number of sent I-frames. 32-bit hex number

NUM_SENT_I_FRAM and range is 0 - FFFFFFFF.
E
bb CSD FTD_SB_NTB_ R X-bit out value 0 or 1.
STATUS_XOUT X0 : Status OFF
X1 : Status ON
cccccccc CSD FTD_SB_NTB_ R Number of retransmitted frames. 32-bit hex
NUM_RETRANS_FR number and range is 0 - FFFFFFFF.
AME
dd CSD FTD_SB_NTB_UPLI R Uplink buffer overflow. 8-bit hex number and
NK_ range is 0 – FF. If not supported xx is shown.
BUF
eeeeeeee CSD FTD_SB_NTB_ R Number of received I-frames. 32-bit hex
NUM_RECV_I_FRA number and range is 0 - FFFFFFFF.
ME
ff CSD FTD_SB_NTB_ R X-bit in. Value is 0 or 1.
STATUS_XIN X0 : Status OFF
X1 : Status ON
gggggggg CSD FTD_SB_NTB_ R Number of SREJ'ed frames. 32-bit hex
NUM_SREJ_FRAME number and range is 0 - FFFFFFFF.
S
hh CSD FTD_SB_NTB_ R Downlink buffer overflow. 8-bit hex number
DOWNLINK_BUF and range is 0 - FF. If not supported xx is
shown.

Display 05.05: Facsimile information (Version: 1, Status: Approved)

Note! This display is not yet updated for 3G phones.

Data Display:

+++++++++++++++++++++++++++
+ Fax call pha aa +
+ Fax class bb +
+ Err corr mode c +
+ MO or MT dd +
+ TrSpd / DTE eee ff +
+ Cts / Cls2St ggg hh +
+ Cls2Us / Cls1 ii j +
+ Flow / OtDT k llll +
+ OfDT / GSM st mmmm n +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa CSD FTD_SB_FAX_PHAS R Shows the phase of the facsimile call when
E Class is 2 or 2.0.
0 : no call (default and in Class 1)
BR : Phase B receive
BT :Phase B transmit
CR : Phase C receive
CT : Phase C transmit
DR : Phase D receive
 SPECIFICATION 50 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

DT : Phase D transmit
E : Phase E
bb CSD FTD_SB_FAX_CLAS R Selected fax class.
S 0 : Not selected yet (default)
1 : Class 1
2 : Class 2
20 : Class 2.0
c CSD FTD_SB_FAX_ECM R Error correction mode.
1 : Used
0 : Not used
dd CSD FTD_SB_FAX_DIR R MO: Mobile originated
MT: mobile terminated.
eee CSD FTD_SB_FAX_ R Negotiated image transfer speed.
IMAGE_TRANS_SPE 0 : not yet negotiated (default)
ED 24 : 2400 bit/s
48 : 4800 bit/s
72 : 7200 bit/s
96 : 9600 bit/s
120 : 12000 bit/s
144 : 14400 bit/s
ff CSD FTD_SB_FAX_ R Number of different DTE sessions for which fax
NUM_SESSIONS has created tables. Range is
0 – 99, default is 0.
ggg CSD FTD_SB_FAX_ R Call termination status, value range is
CALL_TERM_STATU 0 – FF as specified in Appendix A tables A.1 &
S A.2 for Class 2.0 and 0-255 for Class 2 (tables
A.3 & A.4). Default is 0.
hh CSD FTD_SB_FAX_ R Class 2/2.0 substate. 8-bit hex number and
CLASS2_SUBSTATE range is 0 – 2C. (Appendix A,
S Table A.5 )
ii CSD FTD_SB_FAX_ R Class 2/2.0 utility state. 8-bit hex number and
CLASS2_UTIL_STAT range is 0 –1C.
E (Appendix A, Table A.6)
j CSD FTD_SB_FAX_ R Class 1 substate. Range is 0 – 9.
CLASS1_SUBSTATE (Appendix A, Table A.7)
k CSD FTD_SB_FAX_ R Flow control enabled by fax.
FLOW_CTRL 1 : ON
0 : OFF
llll CSD FTD_SB_FAX_ R Buffer towards DTE overflowed, number of lost
TO_DTE_BUF octets shown. Range is 0 – 9999.
m(4) CSD FTD_SB_FAX_ R Buffer from DTE overflowed, number of lost
FROM_DTE_BUF octets shown. Range is 0 – 9999.
n CSD FTD_SB_FAX_ R State of the GSM fax module. Range is 0 – 8.
GSM_STATE (Appendix A, table A.8)

Display 05.06: CSD Server, main data display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ CSD Server main data +
+ DTE ID aaaaaaaaaaaa+
+ TCH ID b +
+ DTE context c +
+ Conf call st def +
 SPECIFICATION 51 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ State machin gggg +

+ GPDS connect h +
+ Pend trans iii +
+ Pend timeout jjjjjj +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(12) CSD FTD_SB_CSDS_ R Existing DTE IDs. Each character represents a
MDD1_DTE_ID DTE (upto 12 separate sessions). DTE ID is 4-bit
hex number and range is 0 – C and x.
x : session doesn't exists
Example: the value 01345xxxxxxx means that
there are five DTE sessions with DTE IDs a0 = 0,
a1 = 1, a2 = 3, a3 = 4 and a4 = 5. F means that the
session ai , i ∈ [5 - 11] doesn't exists.
b CSD FTD_SB_CSDS_ R TCH ID. 4-bit hex number and range is
MDD1_TCH_ID 0 – C and x.
x : Not active
c CSD FTD_SB_CSDS_ R Number of call contexts within DTEs. Range is 0 -
MDD1_NUM_OF_ 6.
CALLS
def CSD FTD_SB_CSDS_ R d = Conference call active.
MDD1_CONFERE A : Active,
NCE x : Not active.
e = Conference call state.
A : Active
H : On hold
x : Not active.
f = DTE ID of conference owner DTE. 4-bit hex
number and range is 0 - C and x.
x : Conference not active.
g(4) CSD FTD_SB_CSDS_ R State Machine state information. 4-bit hex
MDD1_STATE numbers.
g0 = Main state. Range is 0 – 8.
g1 = State branching condition. Range is
0 – F.
g2 = Next state. Range is 0 – 8.
g3 = Call stack depth. Range is 0 – 4.
h CSD FTD_SB_CSDS_ R Number of GPDS connections. 4-bit hex number
MDD1_NUM_ and range is 0 – B.
GPDS_
CONNECTIONS
iii CSD FTD_SB_CSDS_ R Number of pending transactions. Range is 0 -
MDD1_NUM_OF_ 999.
TRANSACTIONS
j(6) CSD FTD_SB_CSDS_ R Number of delta elements (pending time-outs) for
MDD1_MB_ a timer. There are six timers and each of the
TIMER_STATUS timers use one digit (k).
Range is 0 – Z (0 – 40).
j0 : DTR.
j1 : HANGUP.
j2 : ALERT.
j3 : GENERIC.
j4 : DIAL_DELAY.
j5 : USSD_REPLY.
 SPECIFICATION 52 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 05.07: CSD Server, active DTE info 1/2, call related info (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ DTE ID a +
+ Num of calls b +
+ Csta / Cmode cccc dd +
+ TCH ID / Cdi e ff +
+ AcID / HcID gg hh +
+ PeT / Ct inf iii ll +
+ Ctr / NCtr jj kk +
+ SM st / LeID mmmm nnnn+
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a CSD FTD_SB_CSDS_ R DTE ID. 8-bit hex number and range is
ADTE1_DTE_ID 0 – C and x.
x : Not active
b CSD FTD_SB_CSDS_ R Number of calls. Range is 0 – 2.
ADTE1_NUM_OF_
CALLS
cccc CSD FTD_SB_CSDS_ R Current call state.
ADTE1_CALL_STA IDLE : IDLE
TE MTCO : MT CONNECTING
WCON : WAITING CONNECT
CONN : CONNECTED
DISC : DISCONNECTING
dd CSD FTD_SB_CSDS_ R Call mode.
ADTE1_CALL_MO 0 : EMERGENCY
DE 1 : SPEECH
2 : DATA
3 : FAX
A0 : ALT SPEECH DATA
A1 : ALT DATA SPEECH
A2 : ALT SPEECH FAX
A3 : ALT FAX SPEECH
A4 : SPEECH THEN DATA
A5 : UNDEFINED
e CSD FTD_SB_CSDS_ R TCH ID. 8-bit hex number and range is
ADTE1_TCH_ID 0 – C and x.
x : No TCH channel active.
ff CSD FTD_SB_CSDS_ R Call direction.
ADTE1_CALL_DIR MO : Mobile Originated
MT : Mobile Terminated
gg CSD FTD_SB_CSDS_ R Active call ID. 8-bit hex number and range is 0
ADTE1_ACTIVE_C – 9 and 80 – 83.
ALL_ID 0 : CSDC_CALL_ID_NONE
1 – 9 : Call id from CALL server
 SPECIFICATION 53 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

80 : CSDC_CALL_ID_ALL
81 : CSDC_CALL_ID_ACTIVE
82 : CSDC_CALL_ID_HOLD
83 : CSDC_CALL_ID_CONFERENCE
hh CSD FTD_SB_CSDS_ R Held call ID. 8-bit hex number and range is 0 –
ADTE1_ON_HOLD 9 and 80 – 83.
_CALL_ID Interpretation, as above.
iii CSD FTD_SB_CSDS_ R Number of pending transactions. Range is 0 –
ADTE1_NUM_OF_ 999.
PENDING_TRANS
jj/kk CSD FTD_SB_CSDS_ R jj = Call termination reason. 8-bit hex number
ADTE1_CALL_ and range is 0 – 13.
TERM_REASON kk = Network related call termination reason. 8-
bit hex number and range is
1 – 7F.
ll CSD FTD_SB_CSDS_ R l0 = Call termination origin.
ADTE1_CALL_ C : Client
TERM_ORIG_AND S : Server
_DIR N : Network
l1 = Call termination direction.
O : Mobile Originated
T : Mobile Terminated
U : Unspecified / Unknown
mmm CSD FTD_SB_CSDS_ R SM State information. 4-bit hex numbers.
m ADTE1_SM_ m0 = Main state. Range is 0 – 8.
STATE_INFO m1 = State branching condition. Range is 0 – F.
m2 = Next state. Range is 0 – 8.
m3 = Call stack depth. Range is 0 – 4.
nnnn CSD FTD_SB_CSDS_ R Last event id. 16-bit hex value and range is 0 –
ADTE1_LAST_EVE 7FFF.
NT

Display 05.08: CSD Server, active DTE info 2/2, GPDS, socket, conference info (Version: 1,
Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ CSD server DTE,GPDS +
+ DTE ID a +
+ Act call ID bb +
+ GPDS ID,stat cc +
+ GPRS quality dddddd +
+ Socket conn ee +
+ DTE ID f +
+ Conff call st g +
+ Conff call ID hhhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a CSD FTD_SB_CSDS_ R DTE ID. 8-bit hex number and range is
ADTE2_DTE_ID 0 – C and x.
x : No DTE ID available
 SPECIFICATION 54 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

bb CSD FTD_SB_CSDS_ R Active call ID. 8-bit hex number and range is 0 – 9
ADTE2_ACTIVE_ and 80 – 83.
CALL_ID 0 : CSDC_CALL_ID_NONE
1 – 9 : Call id from CALL server
80 : CSDC_CALL_ID_ALL
81 : CSDC_CALL_ID_ACTIVE
82 : CSDC_CALL_ID_HOLD
83 : CSDC_CALL_ID_CONFERENCE
cc CSD FTD_SB_CSDS_ R c0 = GPDS context id. 4-bit hex number and range is
ADTE2_GPDS_ 0 – 7.
CID_AND_STAT c1 = GPDS status value A or D.
E A : Attached
D : Detached
dddddd CSD FTD_SB_CSDS_ R GPRS Quality of service. 4-bit hex numbers.
ADTE2_GPDS_ D0 : Precedence class. Range is 0 – 3.
QOS D1 : Delay class. Range is 0 – 4.
D2 : Reliability class. Range is 0 – 5.
D3 : Peak throughput class.
Range is 0 – 9.
d4 and d5: Mean throughput class. Range is 0 – 13
(8-bit hex).
ee CSD FTD_SB_CSDS_ R Socket connection.
ADTE2_SOCKET 00 : No
_INFO 01 : Yes
f CSD FTD_SB_CSDS_ R DTE ID of a conference owner. 8-bit hex number
ADTE2_ and range is 0 – C and x.
CONFERENCE_ x : No DTE ID available
OWNER
g CSD FTD_SB_CSDS_ R Conference call status.
ADTE2_ A : Active
CONFERENCE_ H : Held
STATUS
h(5) CSD FTD_SB_CSDS_ R Call ids in a conference. Each hi (0 < i < 4) is a call
ADTE2_ id of a participating call.
CONFERENCE_ Each hi is in range 1 – 9.
PARTICIPANTS

Display 05.09: GPRS Rel99 Display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Context info aa b cc dd+
+ Act user cid ee +
+ PDP type fff +
+ QoS gggg +
+ Max up/down hhh iii +
+ SDU error jj +
+ Neg QoS up kkk +
+ Neg Qos down lll +
+ Residual BER mmm +
+++++++++++++++++++++++++++
 SPECIFICATION 55 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

To change GPRS context, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 0509 (TEST GROUP;TEST DISPLAY) to the query
prompt.
5. Test input prompt will be shown on the display, enter the context number in display.
6. Confirm with the Ok button.
7. If change succeeded, the new session information are displayed in display 09 of group 05.

Abbr. Server Sub Block ID Forma Mod Description

t e
aa CSD FTD_SB_GPRS99_ R User context id.
CONTEXT_ID Range is 1 - 10.
b CSD FTD_SB_GPRS99_ R GPRS context state.
CONTEXT_STATE A : Attached
D : Detached
cc CSD FTD_SB_GPRS99_ R GPDS context id. 8-bit hex number.
GPDS_CONTEXT_ID Range is 0 - FF.
dd CSD FTD_SB_GPRS99_ R Number of GPDS connections.
NBR_GPDS_CONNE Range is 0 – 99.
CTIONS
ee CSD FTD_SB_GPRS99_ R Active user cid.
ACT_USER_CID Range is 1 - 10.
fff CSD FTD_SB_GPRS99_ R PDP type.
PDP_TYPE IP : Internet Protocol
IP6 : Internet Protocol version 6
PPP : Point to Point Protocol
gggg CSD FTD_SB_GPRS99_N R Negotiated Qos profile.
EQ_QOS g0 : Traffic class (0-3)
g1 : Delivery order (0-1)
g2 : Delivery of erroneous SDUs (0-2)
g3 : Traffic handling priority (0-2)
hhh CSD FTD_SB_GPRS99_N R Negotiated Qos profile's maximum uplink
EQ_MAX_UL bitrate. Range is 0-64 kbit/s.
iii CSD FTD_SB_GPRS99_N R Negotiated Qos profile's maximum downlink
EQ_MAX_DL bitrate.
Range is 0-384 kbit/s.
jj CSD FTD_SB_GPRS99_S R SDU error ratio.
DER 00 : 0E0 (Subscribed)
11 : E
12 : E2
13 : E3
14 : E4
15: E5
15 : E6
73 : 7E3
FF : Default
kkk CSD FTD_SB_GPRS99_N R Negotiated Qos profile's quaranteed uplink
EQ_GUA_UL bitrate. Range is 0-64 kbit/s.
lll CSD FTD_SB_GPRS99_N R Negotiated Qos profile's quaranteed downlink
EQ_GUA_DL bitrate.
Range is 0-384 kbit/s.
mm CSD FTD_SB_GPRS99_R R Residual bit error rate.
 SPECIFICATION 56 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

BER 00 : 0E0 (Subscribed)

12 : E2
13 : E3
14 : E4
15 : E5
16 : E6
43 : 4E3
52 : 5E2
53 : 5E3
68 : 6E8
FF : Default
INPUT CSD FTD_SB_GPRS99_C DW:D R Change GPRS context.
HANGE_CONTEXT

Display 05.10: MAC Interface Display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ MAC Interface display +
+ +
+ Allowed frame +
+ combinations +
+ +
+ aaaaaaaaa +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(9) CSD FTD_SB_MAC_ALLOWE R Allowed frame combinations for CSD-MAC to
D_COMB use. Each character represents one
combination, 0 means that combination is not
allowed. If zero frame is allowed, then it will be
marked as 1.

an : n = associated transmission frame

a1 = zeroth frame
a9 = eighth frame

Example: 112040008
Means that legal combination of frames
are 0,1,2,4 and 8.
 SPECIFICATION 57 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 05.11: CSD Server Main Data Display, Control 2001 (Version: 1, Status : Approved)

Data Display:

This display is applicable for Kenny.

+++++++++++++++++++++++++++
+ Call mode A +
+ DTE/Calls bb cc +
+ Pending trans ddd +
+ RS Irda e f +
+ UAU UAN ggg hhh +
+ UCU UCN iii jjj +
+ UDU UDN kkk lll +
+ BT/Socket m n +
+ DCP/Unknown o p +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
A CSD FTD_SB_CSDS_ R Active call mode.
MAIN_ACT_CALL_MOD G : GSM
E W : WCDMA
bb CSD FTD_SB_CSDS_ R Number of DTE sessions.
MAIN_NBR_DTE Range: 0 – 50.
cc CSD FTD_SB_CSDS_ R Number of connected calls.
MAIN_NBR_CALL Range: 0 – 99.
ddd CSD FTD_SB_CSDS_ R Number of pending transactions.
MAIN_PENDING_TRAN Range is 0-999.
S
e CSD FTD_SB_CSDS_ R A DTE of the type RS232 connected.
MAIN_RS232 R : If connected
x : No RS232 connection
f CSD FTD_SB_CSDS_ R A DTE of the type IrDA connected.
MAIN_IRDA I : If connected
x : No IrDa connection
ggg CSD FTD_SB_CSDS_ R A DTE of the type USB connected.
MAIN_USB_UAU (AT cmd, unsolicited responses)
UAU : If connection
xxx : No connection
hhh CSD FTD_SB_CSDS_ R A DTE of the type USB connected.
MAIN_USB_UAN (AT cmd, no unsolicited responses)
UAN : If connection
xxx : No connection
iii CSD FTD_SB_CSDS_ R A DTE of the type USB connected.
MAIN_USB_UCU (Modem ctrl, unsolicited responses)
UCU : If connection
xxx : No connection
 SPECIFICATION 58 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

jjj CSD FTD_SB_CSDS_ R A DTE of the type USB connected.

MAIN_USB_UCN (Modem ctrl, no unsolicited responses)
UCN : If connection
xxx : No connection
kkk CSD FTD_SB_CSDS_ R A DTE of the type USB connected.
MAIN_USB_UDU (Modem data, unsolicited responses)
UDU : If connection
xxx : No connection
lll CSD FTD_SB_CSDS_ R A DTE of the type USB connected.
MAIN_USB_UDN (Modem data, no unsolicited responses)
UDN : If connection
xxx : No connection
m CSD FTD_SB_CSDS_MAIN_ R A DTE of the type Bluetooth connected.
BT B : If connected
x : No Bluetooth connection
n CSD FTD_SB_CSDS_MAIN_ R A DTE of the type Socket connected.
SCK S : If connected
x : No Socket connection
o CSD FTD_SB_CSDS_MAIN_ R A DTE of the type DCP connected.
DCP D : If connected
x : No DCP connection
p CSD FTD_SB_CSDS_MAIN_ R An unknown DTE type connected.
UNK U : Unknown connection
x : No unknown connection

Display 05.12: Control DTE and Call Info Displays, Control 2001 (Version: 1, Status: Approved)

Data Display:

Next display is applicable for Kenny.

+++++++++++++++++++++++++++
+ DTE and Call info +
+ +
+ Locked session +
+ +
+ DTE aaa +
+ Call bb +
+ +
+ +
+ +
+++++++++++++++++++++++++++

To change DTE or Call session, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 0512 (TEST GROUP;TEST DISPLAY) to the query
prompt.
5. Test input prompt will be shown on the display, enter the session number in display.
6. Confirm with the Ok button.
 SPECIFICATION 59 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

7. If change succeeded, the new session information are displayed in group 5 display 13 for DTE and
display 14 for Call. Also locked session information are changed in display 12 of group 5.

Abbreviation Description
XX Locked DTE session.
DTE session type.
XX = 1 : RS232
XX = 2 : IRDA
XX = 3 : Bluetooth
XX = 4 : USB AT command, no unsolicited responses
XX = 5 : USB AT command, unsolicited responses
XX = 6 : USB modem control, no unsolicited responses
XX = 7 : USB modem control, unsolicited responses
XX = 8 : USB modem data, no unsolicited responses
XX = 9 : USB modem data, unsolicited responses
XX = 10 : Socket
XX = 11 : DCP
XX = 12 : Unknown
Locked Call session.
2y y : Call ID. Range is 1 – 7.
30 30 : MO call being created
31 31 : MT call being created

Abbr. Serve Sub Block ID Forma Mode Description

r t
a(3) CSD FTD_SB_CSDS_INFO_DT R Show locked DTE session.
E_STATE
bb CSD FTD_SB_CSDS_INFO_CA R Show locked Call session.
LL_STATE
INPUT CSD FTD_SB_CSDS_INFO_CH DW:D R Change DTE or Call display's session.
ANGE_DISPLAY

This display is used for selecting the Call or DTE session the information of which the user wants to
browse.

The CSD server Main Display indicates the total number of existing DTE sessions as well as what types
of DTEs are included. The user selects the DTE session which he wants to browse by indicating the type
of this session.

Call display is selected by entering the Call ID of the call to be browsed. The user finds the correct Call
IDs from the display of the DTE session which owns the call. The user may also request the information
of an MO or MT call that is in the process of being created by typing 30 (MO) or 31 (MT).

Display 05.13: Active DTE Display xx, Control 2001 (Version: 1, Status: Approved)

Data Display:

Display is applicable for Kenny.

 SPECIFICATION 60 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++
+ Active DTE display +
+ +
+ DTE session ID aaa +
+ DTE type bbbbb +
+ Control state ccc +
+ Call ID ddddddd +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(3) CSD FTD_SB_CSDS_ R DTE Session ID.
DTE_SESSION_ID Range is 0 – 255.
b(5) CSD FTD_SB_CSDS_ R DTE type.
DTE_TYPE NONE : Not active
RS : RS232
IRDA : Infra Red Data Association
BT : Bluetooth
SCKT : Socket
DCP : Data Control Protocol
FF : Unknown

Universal Serial Bus

USATN : AT, no unsolicited responses
USATU : AT, unsolicited responses
USMCN: Modem control, no unsolicited
responses
USMCU: Modem control, unsolicited responses
USMDN: Modem data, no unsolicited responses
USMDU: Modem data, unsolicited responses
c(3) CSD FTD_SB_CSDS_ R Control state.
DTE_CTRL_STATE WC: CSDC_WAIT_FOR_COMMAND
CP: CSDC_COMMAND_PROCESSING
WRA:CSDC_WAIT_FOR_REMOTE_ACK
PNC: CSDC_PROCESS_NEXT_CMD
SRM: CSDC_SMS_READ_MODE
d(7) CSD FTD_SB_CSDS_ R Associated call ids.
DTE_CID dn : n = associated call id.
Range is 1 - 7.

Example: the values 1xxx5xx means that

associated call ids are 1 and 5.
 SPECIFICATION 61 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 05.14: Active Call Display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Call ID aaa +
+ Call mode bb +
+ Call type c +
+ Service ddd +
+ Call state eeee +
+ Call dir ff +
+ DTE ID ggg +
+ System h +
+ Cid iii +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaa CSD FTD_SB_CSDS_ R Call ID. Range is 1 – 7.
CALL_ID
bb CSD FTD_SB_CSDS_ R Current Call Mode.
CALL_CURRENT_ EM : EMERGENCY
MODE SP : SPEECH
DA : DATA
FA : FAX
SF : ALT SPEECH FAX
FS : ALT FAX SPEECH
UN : UNDEFINED
c CSD FTD_SB_CSDS_ R Call Type
CALL_TYPE S: Single
D: Dual
ddd CSD FTD_SB_CSDS_ R Service
CALL_SERVICE A: ASYNC
S: SYNC
F1: Fax Class 1
F2: Fax Class 2
F20: Fax Class 2.0
eeee CSD FTD_SB_CSDS_ R Current call state.
CALL_STATE IDLE : CSDC_IDLE
OCM : CSDC_ONLINE_CMD_MODE
DCG : CSDC_DATA_CONNECTING
DCD : CSDC_DATA_CONNECTED
MTA : CSDC_MT_CALL_ANSWERED
MTCG : CSDC_MT_CALL_CONNECTING
MOCG : CSDC_MO_CALL_CONNECTING
VC : CSDC_VOICE_CONNECTED
FCD : CSDC_FAX_CONNECTED
REL : CSDC_CALL_RELEASING
DTMF : CSDC_DTMF_TRANSMIT
ff CSD FTD_SB_CSDS_ R Call direction.
CALL_DIR MO : Mobile Originated
 SPECIFICATION 62 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

MT : Mobile Terminated
ggg CSD FTD_SB_CSDS_ R DTE session ID. Range is 0 – 255.
CALL_SESSION_ID
h CSD FTD_SB_CSDS_ R System.
CALL_SYSTEM G : GSM
W : WCDMA
iii CSD FTD_SB_CSDS_ R TCH/RAB ID. RAB ID if system is WCDMA and
CALL_TCH_RAB_I TCH ID for GSM. In WCDMA system this is left
D empty if RAB ID has not been received. Range is 0
– 255.

Display 05.15: Common CSD Display (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Received TCH aaaaaaaa +
+ Dbug1 bb +
+ Dbug2 cccccccc +
+ Dbug3 dd +
+ Dbug4 eeeeeeee +
+ Dbug5 ff +
+ Dbug6 gggggggg +
+ Dbug7 hh +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(8) CSD FTD_SB_COMMON_NU R Number of received TCH overrun and
M_TCH_OVERRUNS underrun indications from TCH pipe. 32-bit
hex number and range is 0 - FFFFFFFF.
b(2) CSD FTD_SB_COMMON_DE R For general debugging use. String with max.
BUG_1 length 2 +1. (*
c(8) CSD FTD_SB_COMMON_DE R For general debugging use. 32-bit hex number
BUG_2 and range is 0 - FFFFFFFF. (*
d(2) CSD FTD_SB_COMMON_DE R For general debugging use. 8-bit hex number
BUG_3 and range is 0 – FF. (*
e(8) CSD FTD_SB_COMMON_DE R For general debugging use. 32-bit hex number
BUG_4 and range is 0 - FFFFFFFF. (*
f(2) CSD FTD_SB_COMMON_DE R For general debugging use. String with max.
BUG_5 length 2 +1. (*
g(8) CSD FTD_SB_COMMON_DE R For general debugging use. 32-bit hex number
BUG_6 and range is 0 - FFFFFFFF. (*
h(2) CSD FTD_SB_COMMON_DE R For general debugging use. 8-bit hex number
 SPECIFICATION 63 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

BUG_7 and range is 0 – FF. (*

(* See csd_common_ftd.h for more information how to activate debugging fields.

Continuus Server: tresw15
Database Path: /opt/ccm_dbs/tr_dcom
Project Name: csd4_sw
Directory: csd4_sw/common
Filename: csd_common_ftd.h

Display 05.16: Current BC-IE (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ +
+ BC-IE1 BC-IE2 aa bb +
+ BC-IE3 BC-IE4 cc dd +
+ BC-IE5 BC-IE6 ee ff +
+ BC-IE7 BC-IE8 gg hh +
+ BC-IE9 BC-IE10 ii jj +
+ BC-IE11 BC-IE12 kk ll +
+ BC-IE13 BC-IE14 mm nn +
+ +
+++++++++++++++++++++++++++

Abbr Serve Sub Block ID Forma Mod Description

. r t e
aa CSD FTD_SB_BC_IE_OCTE B:H R 1. octet of the BC-IE, which is length. . Range is
T_1 00-FF.
bb CSD FTD_SB_BC_IE_OCTE B:H R 2. octet of the current BC-IE. Range is 00-FF.
T_2
cc CSD FTD_SB_BC_IE_OCTE B:H R 3. octet of the current BC-IE. Range is 00-FF.
T_3
dd CSD FTD_SB_BC_IE_OCTE B:H R 4. octet of the current BC-IE. Range is 00-FF.
T_4
ee CSD FTD_SB_BC_IE_OCTE B:H R 5. octet of the current BC-IE. Range is 00-FF.
T_5
ff CSD FTD_SB_BC_IE_OCTE B:H R 6. octet of the current BC-IE. Range is 00-FF.
T_6
 SPECIFICATION 64 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

gg CSD FTD_SB_BC_IE_OCTE B:H R 7. octet of the current BC-IE. Range is 00-FF.

T_7
hh CSD FTD_SB_BC_IE_OCTE B:H R 8. octet of the current BC-IE. Range is 00-FF.
T_8
ii CSD FTD_SB_BC_IE_OCTE B:H R 9. octet of the current BC-IE. Range is 00-FF.
T_9
jj CSD FTD_SB_BC_IE_OCTE B:H R 10. octet of the current BC-IE. Range is 00-FF.
T_10
kk CSD FTD_SB_BC_IE_OCTE B:H R 11. octet of the current BC-IE. Range is 00-FF.
T_11
ll CSD FTD_SB_BC_IE_OCTE B:H R 12. octet of the current BC-IE. Range is 00-FF.
T_12
mm CSD FTD_SB_BC_IE_OCTE B:H R 13. octet of the current BC-IE. Range is 00-FF.
T_13
nn CSD FTD_SB_BC_IE_OCTE B:H R 14. octet of the current BC-IE. Range is 00-FF.
T_14

Display 05.17: LLC (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ +
+ LLC1 aa +
+ LLC2 bb +
+ LLC3 cc +
+ LLC4 dd +
+ LLC5 ee +
+ LLC6 ff +
+ LLC7 gg +
+ +
+++++++++++++++++++++++++++

Abbr Serve Sub Block ID Forma Mod Description

. r t e
aa CSD FTD_SB_LLC_OCT B:H R 1. octet of the LLC, which is length. .
ET_1 Range is 00-FF.
bb CSD FTD_SB_LLC_OCT B:H R 2. octet of the LLC. Range is 00-FF.
ET_2
cc CSD FTD_SB_LLC_OCT B:H R 3. octet of the LLC. Range is 00-FF.
ET_3
dd CSD FTD_SB_LLC_OCT B:H R 4. octet of the LLC. Range is 00-FF.
ET_4
ee CSD FTD_SB_LLC_OCT B:H R 5. octet of the LLC. Range is 00-FF.
ET_5
ff CSD FTD_SB_LLC_OCT B:H R 6. octet of the LLC. Range is 00-FF.
ET_6
 SPECIFICATION 65 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

gg CSD FTD_SB_LLC_OCT B:H R 7. octet of the LLC. Range is 00-FF.

ET_7
 SPECIFICATION 66 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 06: GPRS Signaling displays

Display 06.01: Information of the current GPRS state and previous TBF configuration (Version:
3.17, Status: Approved)

If MS is not GPRS attached, xxx is shown in all displays.

+++++++++++++++++++++++++++
+ GPRS state and TBF conf.+
+ Hopping/Carrier a b(4)+
+ RX lev / Tadv c(3) d(2)+
+ DL TS / UP TS e f +
+ DL CS / UP CS g h +
+ Tadv I / TFI i j +
+ MAC / Cha type k(4) l(4)+
+ GPRS State m +
+ USF values n(8) +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block ID Form Mode Description

r at
a GSS FTD_SB_GPRS_HOPPI S R,I,O H, if carrier numbers are scrolled when
NG hopping is on. Otherwise empty.
b(4) GSS FTD_SB_GPRS_CARRI W:D R,I,O Carrier number in decimal.
ER If hopping is on, used channels are scrolled
when display is updated
c(3) GSS FTD_SB_GPRS_RX_LE R,I,O Rx level in dBm, minus sign not shown if <=-
VEL 100
d(2) GSS FTD_SB_GPRS_TIMING R,I,O The latest value for timing advance, range 0-
_ADV 63
e GPDS FTD_SB_RLC_DL_SLO B:D R,I,O Downlink time slot count in the latest TBF
TS configuration, range 0-8
f GPDS FTD_SB_RLC_UL_SLO B:D R,I,O Uplink time slot count in the latest TBF
TS configuration, range 0-8.
g GPDS FTD_SB_RLC_DLRX_C B:D R,I,O The Channel Coding Scheme of the latest
S downlink data block, range 1-4.
h GPDS FTD_SB_RLC_ULTX_C B:D R,I,O The Channel Coding Scheme of the latest
S uplink data block, range 1-4.
I(2) GSS FTD_SB_PH_TAI S R,I,O The latest value for timing advance index,
range 0-15. If continuous timing advance
is/was not in use, xx is shown.
j(2) GPDS FTD_SB_MAC_DL_TFI S R,I,O TFI of the latest TBF configuration, range 0-
31. If there is/was no downlink TBF in the
latest TBF configuration, xx is shown.
k(4) GPDS FTD_SB_MAC_ALLOC_ S R,I,O MAC mode, i.e. resource allocation method,
MODE used during the latest TBF configuration:
DYN
EDYN
FIXD
DUSF: USF granularity in use
EUSF: USF granularity in use
F_HD: Fixed Half Duplex
l(4) GSS FTD_SB_GPRS_TYPE_ S Type of current channel
 SPECIFICATION 67 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

OF_CURR_CH In GPRS idle mode, if PBCCH supported in

cell:
PCCC, PBCC, PAGC, PNDR (non-DRX
state):
In GPRS idle mode, if PBCCH not supported
in cell:
AGCH, NDRX (non-DRX state), CCCH,
BCCH
In GPRS transfer mode:
PDTC
Other possibilities are the same as in Display
1 in group 1.

m GPDS FTD_SB_GMM_R_AND_ S R,I,O R if MS is in READY state,

S S if GPRS is suspended and otherwise empty,
n(8) GSS FTD_SB_PH_USF R,I,O USF values of the current TBF configuration,
the first value corresponding timeslot 0, next
timeslot 1 and so on. The range of each USF
value is 0-7. If there is no uplink TBF, or
dynamic allocation was not used in the latest
TBF configuration, xxxxxxxx is shown. If there
is an uplink TBF but not all the 8 time slots are
used, x is shown in place of the unused time
slots.

Display 06.02: Previous UL TBF establishment (Version: 3.15, Status: Approved)

+++++++++++++++++++++++++++
+ UL TBF establighment +
+ +
+ Estab cause a(8) +
+ +
+ Channel req b(5) +
+ +
+ Result of TBF c(7) +
+ +
+ Access type d(7) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(8) GPDS FTD_SB_MAC_UL_ S R,I,O The establishment cause of the previous TBF
TBF_EST_CAUSE establishment:
ONE-PHAS: one-phase access request
SHORT: short access request
TWO-PHAS: two-phase access request
PAGE RES: paging response
CELL UPD: cell update
GMM SIGN: GMM or SM procedure
SINGLE B: single block without TBF
establishment
These correspond the establishment causes in
PACKET CHANNEL REQUEST.
 SPECIFICATION 68 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

b(5) GPDS FTD_SB_MAC_CH_ S R,I,O PRACH: if PACKET CHANNEL REQUEST

REQ_TYPE was sent (PCCCH)
RACH: if CHANNEL REQUEST was sent
(CCCH)
e GPDS FTD_SB_MAC_RADI B:D R,I,O Radio priority, range 1-4.
O_PRIORITY
c(7) GPDS FTD_SB_MAC_TBF S R,I,O Result of the TBF establishment:
_EST_RES OK: TBF establishment succeeded.
REJECT: IMM ASS REJECT (CCCH) or
PACKET ACCESS REJECT (PCCCH)
received from the network.
TIMEOUT: No response to (P)RACH from the
network.
QUEUE: CS channel description received in
IMM ASS (CCCH) or PACKET QUEUING
NOTIFICATION received (PCCCH) and the
TBF was not established (the final result may
still be OK if the TBF was established correctly
after queueing).
FAILURE: TBF establishment failed due to
any other reason.
d(7) GPDS FTD_SB_MAC_TBF S R,I,O The used access type, 1-PHASE or 2-PHASE
_EST_REALIZED access. This informs the finally used method,
regardless of the requested access type. If the
TBF establishment failed, xxxxxx is shown.

Display 06.03: Information of the GMM state (Version: 5.0, Status: Approved)

+++++++++++++++++++++++++++
+ GMM state information +
+ +
+ NW oper mode a(3) +
+ GPRS attach b(8) +
+ GMM state c +
+ MS state d(5) +
+ READY timeout e(3) +
+ T3312 timer f(3) +
+ T3312 / exp g(3) h +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(3) GPDS FTD_SB_GMM_NW S R,I,O Network operation mode
_MODE NW1
NW2
NW3
b(8) GPDS FTD_SB_GMM_ATT S R,I,O The status of GPRS attach:
ACH_TYPE (xxxxxxxx displayed in all these displays in
case no GPRS attach is made)
BOTH: Both IMSI and GPRS attach made
GPRS: GPRS attach only

c GPDS FTD_SB_GMM_ATT S R,I,O The state of GMM

ACH_STATUS c: main state of GMM
 SPECIFICATION 69 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

X idle
R registered
D deregistered

d(5) GPDS FTD_SB_GMM_REA R,I,O READY: MS is in READY state

DY_TMR_STATUS FORCE: MS is in standby state after receiving
"force to standby" indication
STAND: MS is in standby state
(xxxx shown if in IDLE state)
e(3) GPDS FTD_SB_GMM_REA R,I,O The used timeout value for READY timer. Unit
DY_TMR_TIMEOUT seconds. xxx if READY timer is deactivated
f(3) GPDS FTD_SB_GMM_RAU R,I,O Current value of T3312 timer, timer for
_TMR_CURRENT periodical routing area updates. Range is 000
– 186 and unit is minutes.
g(3) GPDS FTD_SB_GMM_RAU R,I,O Timeout value of T3312 timer. Range 000 –
_TMR_TIMEOUT 186 and unit is minutes. xxx if T3312 timer is
deactivated
h GPDS FTD_SB_GMM_PRE S R,I,O F if READY timer expiry preventation
VENT_READY_EXPI mechanism is activated, otherwise empty.
RY

Display 06.04: Values of P-TMSI, RAC, SMS radio priority, Ciphering and Non-DRX parameters
(Version: 3.15, Status: Approved)

+++++++++++++++++++++++++++
+ Ciphering and non-DRX +
+ parameters +
+ +
+ P-TMSI a(8) +
+ RAI b(4) +
+ Ciphering c(4) +
+ SPLIT_PG_CYC d(3) +
+ Non-DRX timer e(2) +
+ SMS radio pri f +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(8) GPDS FTD_SB_GMM_PTM R,I,O P-TMSI value in hex format
SI_VALUE
b(4) GPDS FTD_SB_GMM_RAI R,I,O RAI (Routing Area Indicator) in hex format
_VALUE
c(4) GPDS FTD_SB_GMM_CIP R,I,O Ciphering value (negotiated by GMM):
HERING_VALUE OFF/GEA1/GEA2 Note! Even if the value here
would show that ciphering is used, LLC may
still send and receive unciphered blocks.
d(3) GPDS FTD_SB_GMM_SPL R,I,O SPLIT_PG_CYCLE value indicated by MS.
IT_PG_CYCLE_VAL 704 if non-DRX is used, otherwise range is 1-
UE 352. 0 is shown if SPLIT_PG_CYCLE is not in
use in CCCH.
e(2) GPDS FTD_SB_GMM_NO R,I,O non-DRX timer indicated by MS. (The actually
N_DRX_TMR used value is a minimum of this and the
network parameter.) 0 if no non-DRX mode is
 SPECIFICATION 70 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

used after transfer mode, otherwise range is

1-64 seconds.
f GPDS FTD_SB_GMM_SM R,I,O SMS radio priority, range 1-4. If MO SMS via
S_PRIORITY GPRS is not allowed, x is shown.

Display 06.05: GPRS Network parameters (Version: 3.15, Status: Approved)

+++++++++++++++++++++++++++
+ GPRS network parameters +
+ +
+ CTRL_ACK type a(4) +
+ ACCESS_BURST b(2) +
+ DRX_TIMER_MAX c(2) +
+ SPLIT support d +
+ Paging mode e(2) +
+ NC mode f(3) +
+ T3168 timer g +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(4) FTD_SB_MAC_CTRL R,I,O The value of CONTROL_ACK_TYPE
_ACK_TYPE 4ACC: PACKET CONTROL
ACKNOWLEDGEMENT is sent as 4 access
bursts.
CTRL: PACKET CONTROL
ACKNOWLEDGEMENT is sent as RLC/MAC
control block.
b(2) FTD_SB_MAC_ACC_ R,I,O The value of ACCESS_BURST_TYPE, either 8
BURST_TYPE or 11 [bits].
c(2) FTD_SB_MAC_DRX_ R,I,O The value of DRX_TIMER_MAX, range 1 – 64
TIMER_MAX seconds.
d FTD_SB_MAC_SPLIT R,I,O The value of
_PG_CYCLE_ON_CC SPLIT_PG_CYCLE_CCCH_SUPPORTED,
CH range 0-1. If PBCCH is supported, x is shown.
e(2) FTD_SB_MAC_PAGE R,I,O Paging mode:
_MODE NO: normal paging
EX: extended paging
RO: paging reorganization
SB: same as before
f(3) FTD_SB_MAC_NCM R,I,O NC mode indicated in system information. If
ODE_BROADCAST GPRS not supported, xxx is shown.
NC0: No measurement reports, MS decides of
the cell re-selections
NC1: Measurement reports. MS decides of the
cell re-selections
NC2: Measurement reports. The network
commands the cell re-selections.
g FTD_SB_MAC_T3168 R,I,O The value of T3168 timer, range 0-7,
_VALUE corresponding 0.5s, 1s,…, 4s.
 SPECIFICATION 71 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 06.06: Packet control channel parameters (Version: 4.0, Status: Approved)

If PCCCH is not supported, xxx is shown in all fields

+++++++++++++++++++++++++++
+ PCCCH parameters +
+ +
+ BS_PBCCH_BLKS a +
+ BS_PCC_CHANS b(2)+
+ BS_PAG_BLCKS_RES c(2)+
+ BS_PCC_REL d +
+ BS_PRACH_BLKS e(2)+
+ Hopping of PBCCH g +
+ Hopping of PCCCH h +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a GPDS FTD_SB_BS_PBCCH R,I,O Value of BS_PBCCH_BLKS, range 1-4.
_BLKS
g GSS FTD_SB_PBCCH_HO R,I,O Hopping of PBCCH
PPING H if PBCCH is hopping, otherwise empty
b(2) GPDS FTD_SB_BS_PCC_C R,I,O Value of BS_PCC_CHANS, range 1-16.
HANS
h GSS FTD_SB_PCCCH_HO R,I,O Hopping of PCCCH
PPING H if PCCCH is hopping, otherwise empty (also if
BS_PCC_CHANS=1)
c(2) GPDS FTD_SB_BS_PAG_BL R,I,O Value of BS_PAG_BLCKS_RES, range 0-12.
KS_RES
d GPDS FTD_SB_BS_PCC_R R,I,O Value of BS_PCC_REL, range 0-1.
EL
e(2) GPDS FTD_SB_BS_PRACH R,I,O Value of BS_PRACH_BLKS, range 0-12.
_BLKS

Display 06.07: (Packet) System information parameters (Version: 5.0, Status: Approved)

+++++++++++++++++++++++++++
+ System information +
+ +
+ Sys 13 / Sys 5 a(4) b +
+ PSI repeat/ LR c(2)d(2)+
+ PSI_HR/ Status e(2) f +
 SPECIFICATION 72 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ MSCR / SGSNR g h +
+ SI ind/NW EXT i j +
+ CCN / PFC mode k l +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(4) GSS FTD_SB_PH_SI13_L R,I,O The location of System information 13.
OCATION NORM: SI 13 available at BCCH Norm
EXT: SI 13 available at BCCH Ext
b GPDS FTD_SB_MAC_PSI5_ R,I,O The availability of Packet system information 5
BROADCAST (optional)
0: PSI 5 not supported
1: PSI 5 supported
c(2) GPDS FTD_SB_MAC_PSI1_ R,I,O The value of PSI_REPEAT_PERIOD, range 1-
REPEAT_PERIOD 16. If PBCCH is not supported, xx is shown.
d(2) GPDS FTD_SB_MAC_PSI_C R,I,O The value of PSI_COUNT_LR, range 0-63. If
OUNT_LR PBCCH is not supported, xx is shown.
e(2) GPDS FTD_SB_MAC_PSI_C R,I,O The value of PSI_COUNT_HR, range 0-63. If
OUNT_HR PBCCH is not supported, xx is shown.
f GPDS FTD_SB_MAC_PSI_S R,I,O The value of PSI_STATUS_IND, range 0-1. If 1,
TATUS network supports the PACKET PSI_STATUS
message. If PBCCH is not supported, x is shown.
g GSS FTD_SB_PH_MSCR B:D R,I,0 Value of MSCR bit, range 0-1.
If 0, MSC is Release ’98 or older, or info not
availaible
If 1, MSC is Release ’99 onwards
h GSS FTD_SB_PH_SGSNR B:D R;I;O Value of SGSNR bit, range 0-1
If 0, SGSN is Release ’98 or older, or info not
available
If 1, SGSN is Release ’99 onwards
i GSS FTD_SB_PH_SI_STA B:D R;I;O The value of SI_STATUS_IND, range 0-1. If 1,
TUS_IND network supports the PACKET SI_STATUS
message. If PBCCH is supported, x is shown.
j GSS FTD_SB_PH_EXT_UT B:D R;I;O The value of NW_EXT_UTBF, range 0-1. If 1,
BF network supports the extended UL TBF mode
(Rel4).
k GSS FTD_SB_PH_CCN_A B:D R;I;O The value of CCN_ACTIVE, range 0-1. If 1,
CTIVE network supports Cell Change Notification
procedures (Rel4)
l GSS FTD_SB_PH_PFC_FE B:D R;I;O The value of PFC_FEATURE_MODE, range 0-1.
ATURE_MODE If 1, network supports packet flow context
procedures.

Display 06.08: Cell re-selection parameters (serving cell) (Version: 3.15, Status: Approved)

xx is shown in all fields if MS performs cell re-selections with GSM cell re-selection algorithm, i.e. if
PBCCH is not supported and if neither PACKET MEAS ORDER nor PACKET CELL CHANGE
ORDER has been received. xx is also shown in a specific field if the value is not available
+++++++++++++++++++++++++++
+ Cell re-selection param +
 SPECIFICATION 73 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ +
+ RXLEV_ACCESS_MIN a(2) +
+ CELL_RESELECT_HYS b(2) +
+ RA_RESELECT_HYSTE c(2) +
+ C31_HYST d +
+ C32_QUAL e +
+ RANDOM_ACC_RETRY f +
+ T_RESEL g(4) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(2) GSS FTD_SB_G R,I,O The value of GPRS_RXLEV_ACCESS_MIN, range 0-63.
PRS_RXLE
V_ACC_MIN
b(2) GSS FTD_SB_ R,I,O The value of GPRS_CELL_RESELECT_HYSTERESIS,
GPRS_CEL range 0-14 [dB].
L_RESEL_H
YST
c(2) GSS FTD_SB_ R,I,O The value of RA_RESELECT_HYSTERESIS, range 0-14
RA_RESEL_ [dB].
HYST
d GSS FTD_SB_ R,I,O The value of C31_HYST, range 0-1.
C31_HYST
e GSS FTD_SB_ R,I,O The value of C32_QUAL, range 0-1.
C32_QUAL
f GSS FTD_SB_ R,I,O The value of RANDOM_ACCESS_RETRY, range 0-1.
RAND_ACC
_RETRY
g(4) GSS FTD_SB_ R,I,O The value of T_RESEL, range 5-300 [seconds].
T_RESEL

Display 06.09: GPRS information of the serving cell, 1st, 2nd, and 3rd neighbor (Version: 3.19,
Status: Approved)

2. row: serving cell information

4. row: 1. neighbor information
6. row: 2. neighbor information
8. row: 3. neighbor information

xx is shown in all fields if MS performs cell re-selections with GSM cell re-selection algorithm, i.e. if
PBCCH is not supported and if neither PACKET MEAS ORDER nor PACKET CELL CHANGE
ORDER has been received.
+++++++++++++++++++++++++++
+ GPRS Serving cell info +
+ CH: Rx: PRI: C32:+
+ aaa bbb c ddd +
+ 1. Neighbor info +
+ eee fff g hhh +
+ 2. Neighbor info +
+ iii jjj k lll +
 SPECIFICATION 74 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ 3. Neighbor info +
+ mmm nnn o ppp +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(3) GSS FTD_SB_GPRS_CAR R,I,O Carrier number in decimal.
RIER_SERV
b(3) GSS FTD_SB_GPRS_RX_ R,I,O Rx level in dBm, minus sign not shown if <=-100.
LEVEL_SERV
c GSS FTD_SB_PRIOR_CLA R,I,O PRIORITY_CLASS, range 0-7. Shown only when
SS_SERV C31>=0, otherwise left empty. If HCS parameters
are not available (optional), x is shown.
d(3) GSS FTD_SB_C32_SERV R,I,O C32 value. For the serving cell, C32 equals C1.
The neighbours are sorted first based on the
priority class (biggest priority on top). Within each
priority class the neighbours are sorted based on
C32 value. The neighbors are sorted based on
only C32, if all the C31 values are negative (c-
fields empty) or if priorities are not available (x
shown in c-fields).
e(3) GSS FTD_SB_GPRS_CAR R,I,O Carrier number in decimal.
RIER_1_NEIGH
f(3) GSS FTD_SB_GPRS_RX_ R,I,O Rx level in dBm, minus sign not shown if <=-100.
LEVEL_1_NEIGH
g GSS FTD_SB_PRIOR_CLA R,I,O PRIORITY_CLASS, range 0-7. Shown only when
SS_1_NEIGH C31>=0, otherwise left empty. If HCS parameters
are not available (optional), x is shown.
h(3) GSS FTD_SB_C32_1_NEI R,I,O C32 value. For the serving cell, C32 equals C1.
GH The neighbours are sorted first based on the
priority class (biggest priority on top). Within each
priority class the neighbours are sorted based on
C32 value. The neighbors are sorted based on
only C32, if all the C31 values are negative (c-
fields empty) or if priorities are not available (x
shown in c-fields).
i(3) GSS FTD_SB_GPRS_CAR R,I,O Carrier number in decimal.
RIER_2_NEIGH
j(3) GSS FTD_SB_GPRS_RX_ R,I,O Rx level in dBm, minus sign not shown if <=-100.
LEVEL_2_NEIGH
k GSS FTD_SB_PRIOR_CLA R,I,O PRIORITY_CLASS, range 0-7. Shown only when
SS_2_NEIGH C31>=0, otherwise left empty. If HCS parameters
are not available (optional), x is shown.
l(3) GSS FTD_SB_C32_2_NEI R,I,O C32 value. For the serving cell, C32 equals C1.
GH The neighbours are sorted first based on the
priority class (biggest priority on top). Within each
priority class the neighbours are sorted based on
C32 value. The neighbors are sorted based on
only C32, if all the C31 values are negative (c-
fields empty) or if priorities are not available (x
shown in c-fields).
m(3) GSS FTD_SB_GPRS_CAR R,I,O Carrier number in decimal.
RIER_3_NEIGH
n(3) GSS FTD_SB_GPRS_RX_ R,I,O Rx level in dBm, minus sign not shown if <=-100.
LEVEL_3_NEIGH
o GSS FTD_SB_PRIOR_CLA R,I,O PRIORITY_CLASS, range 0-7. Shown only when
SS_3_NEIGH C31>=0, otherwise left empty. If HCS parameters
 SPECIFICATION 75 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

are not available (optional), x is shown.

p(3) GSS FTD_SB_C32_3_NEI R,I,O C32 value. For the serving cell, C32 equals C1.
GH The neighbours are sorted first based on the
priority class (biggest priority on top). Within each
priority class the neighbours are sorted based on
C32 value. The neighbors are sorted based on
only C32, if all the C31 values are negative (c-
fields empty) or if priorities are not available (x
shown in c-fields).

Display 06.10: GPRS information of the 4th,5th and 6th neighbor (Version: 3.15, Status: Approved)

2. row: 4. neighbor information

4. row: 5. neighbor information
6. row: 6. neighbor information

xx is shown in all fields if MS performs cell re-selections with GSM cell re-selection algorithm, i.e. if
PBCCH is not supported and if neither PACKET MEAS ORDER nor PACKET CELL CHANGE
ORDER has been received.

+++++++++++++++++++++++++++
+ +
+ 4. Neighbor info +
+ CH: Rx: PRI: C32:+
+ aaa bbb c ddd +
+ 5. Neighbor info +
+ eee fff g hhh +
+ 6. Neighbor info +
+ iii jjj k lll +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(3) GSS FTD_SB_G R,I,O Carrier number in decimal.
PRS_CARRI
ER_4_NEIG
H
b(3) GSS FTD_SB_G R,I,O Rx level in dBm, minus sign not shown if <=-100.
PRS_RX_LE
VEL_4_NEI
GH
c GSS FTD_SB_PR R,I,O PRIORITY_CLASS, range 0-7. Shown only when C31>=0,
IOR_CLASS otherwise left empty. If HCS parameters are not available
_4_NEIGH (optional), x is shown.
d(3) GSS FTD_SB_C3 R,I,O C32 value. The neighbours are sorted first based on the
2_4_NEIGH priority class (biggest priority on top). Within each priority
class the neighbours are sorted based on C32 value. The
neighbors are sorted based on only C32, if all the C31
values are negative (c-fields empty) or if priorities are not
 SPECIFICATION 76 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

available (x shown in c-fields).

e(3) GSS FTD_SB_G R,I,O Carrier number in decimal.
PRS_CARRI
ER_5_NEIG
H
f(3) GSS FTD_SB_G R,I,O Rx level in dBm, minus sign not shown if <=-100.
PRS_RX_LE
VEL_5_NEI
GH
g GSS FTD_SB_PR R,I,O PRIORITY_CLASS, range 0-7. Shown only when C31>=0,
IOR_CLASS otherwise left empty. If HCS parameters are not available
_5_NEIGH (optional), x is shown.
h(3) GSS FTD_SB_C3 R,I,O C32 value. The neighbours are sorted first based on the
2_5_NEIGH priority class (biggest priority on top). Within each priority
class the neighbours are sorted based on C32 value. The
neighbors are sorted based on only C32, if all the C31
values are negative (c-fields empty) or if priorities are not
available (x shown in c-fields).
i(3) GSS FTD_SB_G R,I,O Carrier number in decimal.
PRS_CARRI
ER_6_NEIG
H
j(3) GSS FTD_SB_G R,I,O Rx level in dBm, minus sign not shown if <=-100.
PRS_RX_LE
VEL_6_NEI
GH
k GSS FTD_SB_PR R,I,O PRIORITY_CLASS, range 0-7. Shown only when C31>=0,
IOR_CLASS otherwise left empty. If HCS parameters are not available
_6_NEIGH (optional), x is shown.
l(3) GSS FTD_SB_C3 R,I,O C32 value. The neighbours are sorted first based on the
2_6_NEIGH priority class (biggest priority on top). Within each priority
class the neighbours are sorted based on C32 value. The
neighbors are sorted based on only C32, if all the C31
values are negative (c-fields empty) or if priorities are not
available (x shown in c-fields).

Display 06.11: GPRS information of the serving cell and 6 neighbors (Version: 3.16, Status:
Approved)

1. row: serving cell information

2. row: 1. neighbor on the left, 4. neighbor on the right
3. row: 2. neighbor on the left, 5. neighbor on the right
4. row: 3. neighbor on the left, 6. neighbor on the right

xx is shown in all fields if MS performs cell re-selections with GSM cell re-selection
algorithm, i.e. if PBCCH is not supported and if neither PACKET MEAS ORDER nor
PACKET CELL CHANGE ORDER has been received.

+++++++++++++++++++++++++++
+ Serving cell a c d +
+ 1. neighbor b c d +
+ 2. neighbor b c d +
+ 3. neighbor b c d +
 SPECIFICATION 77 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ 4. neighbor b c d +
+ 5. neighbor b c d +
+ 6. neighbor b c d +
+ a=MS READY b=Same RA +
+ c=CELL_BAR d=EXC_ACC +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block Forma Mod Description

r ID t e
Display row 1: serving cell information
a GSS FTD_SB_G R,I,O R if MS is in READY state and therefore applies hysteresis
MM_STAT for cell re-selection.
E
c GSS FTD_SB_C R,I,O The value of CELL_BAR_ACCESS_2. x is shown if PBCCH
ELL_BAR_ is not supported.
ACC_2
d GSS FTD_SB_E R,I,O The value of EXC_ACC. x is shown if PBCCH is not
XC_ACC supported.
st
Display row 2, left side: 1 neighbor
b GSS FTD_SB_S R,I,O The value of SAME_RA_AS_SERVING_CELL:
AME_RA_A 1: cell belongs to the same routing area as the serving cell
S_SRV_CE 0: cell belongs to the different routing area as the serving
LL_1_NEIG cell
H
c GSS FTD_SB_C R,I,O The value of CELL_BAR_ACCESS_2. x is shown if PBCCH
ELL_BAR_ is not supported.
ACC_2_1_
NEIGH
d GSS FTD_SB_E R,I,O The value of EXC_ACC. x is shown if PBCCH is not
XC_ACC_1 supported.
_NEIGH
Display row 3, left side: 2nd neighbor
b GSS FTD_SB_S R,I,O The value of SAME_RA_AS_SERVING_CELL:
AME_RA_A 1: cell belongs to the same routing area as the serving cell
S_SRV_CE 0: cell belongs to the different routing area as the serving
LL_2_NEIG cell
H
c GSS FTD_SB_C R,I,O The value of CELL_BAR_ACCESS_2. x is shown if PBCCH
ELL_BAR_ is not supported.
ACC_2_2_
NEIGH
d GSS FTD_SB_E R,I,O The value of EXC_ACC. x is shown if PBCCH is not
XC_ACC_2 supported.
_NEIGH
rd
Display row 4, right side: 3 neighbor
b GSS FTD_SB_S R,I,O The value of SAME_RA_AS_SERVING_CELL:
AME_RA_A 1: cell belongs to the same routing area as the serving cell
S_SRV_CE 0: cell belongs to the different routing area as the serving
LL_3_NEIG cell
H
c GSS FTD_SB_C R,I,O The value of CELL_BAR_ACCESS_2. x is shown if PBCCH
ELL_BAR_ is not supported.
ACC_2_3_
NEIGH
d GSS FTD_SB_E R,I,O The value of EXC_ACC. x is shown if PBCCH is not
XC_ACC_3 supported.
 SPECIFICATION 78 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

_NEIGH
th
Display row 2, right side: 4 neighbor
b GSS FTD_SB_S R,I,O The value of SAME_RA_AS_SERVING_CELL:
AME_RA_A 1: cell belongs to the same routing area as the serving cell
S_SRV_CE 0: cell belongs to the different routing area as the serving
LL_4_NEIG cell
H
c GSS FTD_SB_C R,I,O The value of CELL_BAR_ACCESS_2. x is shown if PBCCH
ELL_BAR_ is not supported.
ACC_2_4_
NEIGH
d GSS FTD_SB_E R,I,O The value of EXC_ACC. x is shown if PBCCH is not
XC_ACC_4 supported.
_NEIGH
th
Display row 3, right side: 5 neighbor
b GSS FTD_SB_S R,I,O The value of SAME_RA_AS_SERVING_CELL:
AME_RA_A 1: cell belongs to the same routing area as the serving cell
S_SRV_CE 0: cell belongs to the different routing area as the serving
LL_5_NEIG cell
H
c GSS FTD_SB_C R,I,O The value of CELL_BAR_ACCESS_2. x is shown if PBCCH
ELL_BAR_ is not supported.
ACC_2_5_
NEIGH
d GSS FTD_SB_E R,I,O The value of EXC_ACC. x is shown if PBCCH is not
XC_ACC_5 supported.
_NEIGH
th
Display row 4, right side: 6 neighbor
b GSS FTD_SB_S R,I,O The value of SAME_RA_AS_SERVING_CELL:
AME_RA_A 1: cell belongs to the same routing area as the serving cell
S_SRV_CE 0: cell belongs to the different routing area as the serving
LL_6_NEIG cell
H
c GSS FTD_SB_C R,I,O The value of CELL_BAR_ACCESS_2. x is shown if PBCCH
ELL_BAR_ is not supported.
ACC_2_6_
NEIGH
d GSS FTD_SB_E R,I,O The value of EXC_ACC. x is shown if PBCCH is not
XC_ACC_6 supported.
_NEIGH

Display 06.12: EGPRS specific parameters (Version: 3.24, Status: Approved)

+++++++++++++++++++++++++++
+ EGPRS parameters +
+ +
+ EDGE Supported a +
+ Packet Channel +
+ request supported b +
+ BEP period or +
+ Bep period2 c(2) +
 SPECIFICATION 79 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Used link qual +

+ measurement mode d(2) +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a GSS FTD_SB_EGPRS_SUPPORT B:D R,I,O 1=EGPRS supported in cell; 0=not
supported
b GSS FTD_SB_EGPRS_PACKET B:D R,I,O 1=EGPRS packet channel request
CHANNEL _REQUEST supported in cell; 0=not supported
c(2) GSS FTD_SB_EGPRS_BEP_PER B:H R,I,O BEP_PERIOD, or BEP_PERIOD2
when received
d(2) GPDS FTD_SB_EGPRS_LQ_MEAS_ ? R,I,O Used link quality measurement
MODE mode

Display 06.13: EGPRS BEP parameters (Version: 5.0, Status: Approved)

+++++++++++++++++++++++++++
+ EGPRS BEP parameters +
+ +
+ GMSK Bit error +
+ probapility a +
+ 8-PSK Bit error +
+ probapility b +
+ GMSK Bit error +
+ variation c(2) +
+ 8-PSK Bit error +
+ variation d(2) +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(2) GPDS FTD_SB_EGPRS_ B:D R This field contains the mean value of the Bit
BEP_MEAN_GPSK Error Probability of the channel averaged over
all time slots in the TBF for GMSK, refer to
3GPP TS 05.08.
Range 0-31
b GPDS FTD_SB_EGPRS_ B:D R This field contains the mean value of the Bit
BEP_CV_GPSK Error Probability of the channel averaged over
all time slots in the TBF for 8 PSK, refer to
3GPP TS 05.08.
Range 0-7
c(2) GPDS FTD_SB_EGPRS_ B:D R This field contains the variation co-efficient for
BEP_MEAN_8PSK the Bit Error Probability averaged over all time
slots of the TBF for GMSK, refer to 3GPP TS
05.08.
Range 0-31
d GPDS FTD_SB_EGPRS_ B:D R This field contains the variation co-efficient for
BEP_CV_8PSK the Bit Error Probability averaged over all time
slots of the TBF for 8 PSK, refer to 3GPP TS
05.08.
Range 0-7
 SPECIFICATION 80 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 07: GPRS Data protocol displays

Display 07.01: Information of the first active PDP context (Version: 3.22, Status: Approved)

If no PDP context is active, xx is shown in all fields. In 2G/3G products, xx is shown in all fields
except NSAPI and SAPI.

+++++++++++++++++++++++++++
+ 1. active PDP context +
+ +
+ NSAPI / SAPI a(2) b +
+ Relia / Delay c d +
+ Prece / peak e f +
+ Mean / prior g(2) h +
+ VanJac/V.42bis i j +
+ PDP addr of PDP context +
+ k(3).l(3).m(3).n(3) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa GPDS FTD_SB_GPDS_NSA R,I,O NSAPI of the PDP context, range 5-15.
PI_1
b GPDS FTD_SB_GPDS_SAPI R,I,O SAPI of the PDP context: 3,5,9 or B (=11)
_1
c GPDS FTD_SB_SN_RELC_1 R,I,O The negotiated reliability class of the PDP
context, range 1-5.
d GPDS FTD_SB_SN_DELC_1 R,I,O The negotiated delay class of the PDP context,
range 1-4.
e GPDS FTD_SB_SN_PREC_ R,I,O The negotiated precedence class of the PDP
1 context, range 1-3

f GPDS FTD_SB_SN_PTPC_1 R,I,O The negotiated peak throughput, range 1-9.

gg GPDS FTD_SB_SN_MTPC_ R,I,O The negotiated mean throughput, range 1-18 or
1 B (=best effort).
h GPDS FTD_SB_SN_RPRI_1 R,I,O The radio priority of the PDP context, range 1-4.
i GPDS FTD_SB_SN_HCOMP R,I,O P if protocol compression (VanJacobsen)
_1 isnegotiated to be usedotherwise empty.
j GPDS FTD_SB_SN_DCOMP R,I,O D if data compression (V.42bis) is negotiated to
_1 be used
otherwise empty.
kkk GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 1.
_ADDRESS_1_1 Format IPv4 address.
lll GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 2.
_ADDRESS_1_2 Format IPv4 address.
mmm GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 3.
_ADDRESS_1_3 Format IPv4 address.
nnn GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 4.
_ADDRESS_1_4 Format IPv4 address.
 SPECIFICATION 81 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 07.02: Information of the second active PDP context (Version: 3.22, Status: Approved)

If no PDP context is active, xx is shown in all fields. In 2G/3G products, xx is shown in all fields
except NSAPI and SAPI.

+++++++++++++++++++++++++++
+ 2. active PDP context +
+ +
+ NSAPI / SAPI a(2) b +
+ Relia / Delay c d +
+ Prece / peak e f +
+ Mean / prior g(2) h +
+ VanJac/V.42bis i j +
+ PDP addr of PDP context +
+ k(3).l(3).m(3).n(3) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa GPDS FTD_SB_GPDS_NSA R,I,O NSAPI of the PDP context, range 5-15.
PI_2
b GPDS FTD_SB_GPDS_SAPI R,I,O SAPI of the PDP context: 3,5,9 or B (=11)
_2
c GPDS FTD_SB_SN_RELC_2 R,I,O The negotiated reliability class of the PDP
context, range 1-5.
d GPDS FTD_SB_SN_DELC_2 R,I,O The negotiated delay class of the PDP context,
range 1-4.
e GPDS FTD_SB_SN_PREC_ R,I,O The negotiated precedence class of the PDP
2 context, range 1-3

f GPDS FTD_SB_SN_PTPC_2 R,I,O The negotiated peak throughput, range 1-9.

gg GPDS FTD_SB_SN_MTPC_ R,I,O The negotiated mean throughput, range 1-18 or
2 B (=best effort).
h GPDS FTD_SB_SN_RPRI_2 R,I,O The radio priority of the PDP context, range 1-4.
i GPDS FTD_SB_SN_HCOMP R,I,O P if protocol compression (VanJacobsen) is
_2 negotiated to be used
otherwise empty.
j GPDS FTD_SB_SN_DCOMP R,I,O D if data compression (V.42bis) is negotiated to
_2 be used
otherwise empty.
kkk GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 1.
_ADDRESS_2_1 Format IPv4 address.
lll GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 2.
_ADDRESS_2_1 Format IPv4 address.
mmm GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 3.
_ADDRESS_2_3 Format IPv4 address.
nnn GPDS FTD_SB_GPDS_PDP R,I,O The PDP address of the PDP context, part 4.
_ADDRESS_2_4 Format IPv4 address.
 SPECIFICATION 82 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 07.03: Information of the RLC state (Version: 1, Status: Approved)

If no TBF is active, xx is shown in all fields.

+++++++++++++++++++++++++++
+ RLC state information +
+ Downlink TS a +
+ Coding scheme b +
+ RLC mode down c(c) +
+ Uplink TS d +
+ Coding scheme e +
+ RLC mode up f(4) +
+ UL TBF g(g) +
+ N3102 state i(2) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a GPDS FTD_SB_RLC_DL_SL R,I,O Downlink time slot count, range 1-8. If no
OTS downlink TBF is active, x is shown.
b GPDS FTD_SB_RLC_DL_C R,I,O Channel coding scheme in downlink direction,
H_CODE range 1-4. If no downlink TBF is active, x is
shown.
cccc GPDS FTD_SB_RLC_DL_M R,I,O RLC mode in downlink direction. If no downlink
ODE TBF is active, xxxxx is shown.
ACK: RLC in acknowledged mode
UNAC: RLC in unacknowledged mode
d GPDS FTD_SB_RLC_UL_SL R,I,O Upink time slot count, range 1-8. If no upink TBF
OTS is active, x is shown.
e GPDS FTD_SB_RLC_UL_C R,I,O Channel coding scheme in uplink direction,
H_CODE range 1-4. If no uplink TBF is active, x is shown.
ffff GPDS FTD_SB_RLC_UL_M R,I,O RLC mode in uplink direction. If no uplink TBF is
ODE active, xxxx is shown.
ACK: RLC in acknowledged mode
UNAC: RLC in unacknowledged mode
ggggg GPDS FTD_SB_RLC_ENDIN R,I,O xxxxx when no UL TBF is active
G_MODE CLOSE when UL TBF is close-ended TBF
OPEN when UL TBF is open-ended TBF
ii GPDS FTD_SB_RLC_N3102 R,I,O The state of N3102 counter, range 0-PAN_MAX
(negative values are also shown as 0). If the
counter is disabled, x is shown.
 SPECIFICATION 83 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 07.04: RLC parameters (Version: 1, Status: Approved)

xx is shown in the fields when the values are not available (e.g. no GPRS support in the cell, no GPRS
attach performed).

+++++++++++++++++++++++++++
+ RLC parameters +
+ +
+ T3192 timer a(2) +
+ BS_CV_MAX c(2) +
+ PAN_DEC d +
+ PAN_INC e +
+ PAN_MAX f(f) +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa GPDS FTD_SB_RLC_T3192 R,I,O The value of T3192 timer, range 0-7,
corresponding 0.5s, 1s,…, 4s.
Bb GPDS FTD_SB_RLC_BS_C R,I,O The value of BS_CV_MAX, range 1-15. Tells
V_MAX how many radio block periods the countdown
procedure lasts in the end of UL TBF.
c GPDS FTD_SB_RLC_PAN_ R,I,O The value of PAN_DEC, range 0-7. If PAN_DEC
DEC and PAN_INC are equal to 0, N3102 counter is
disabled.
d GPDS FTD_SB_RLC_PAN_I R,I,O The value of PAN_INC, range 0-7. If PAN_DEC
NC and PAN_INC are equal to 0, N3102 counter is
disabled.
ee GPDS FTD_SB_RLC_PAN_ R,I,O The value of PAN_MAX, range 4-32.
MAX

Display 07.05: RLC data block counters (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ RLC data block counters +
+ +
+ Received blocks b(4) +
+ Sent blocks d(4) +
+ Missing DL blocks f(4) +
+ Req retrans uplink h(4) +
 SPECIFICATION 84 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
bbbb GPDS FTD_SB_RLC_BLOC R,I,O Counter for received RLC data blocks
KS_RECV
dddd GPDS FTD_SB_RLC_BLOC R,I,O Counter for sent RLC data blocks
KS_SENT
ffff GPDS FTD_SB_RLC_BLOC R,I,O Counter for detected missing downlink data
KS_MISS blocks
hhhh GPDS FTD_SB_RLC_BLOC R,I,O Counter for requested re-transmissions of the
KS_RESENT uplink RLC data blocks

Display 07.06: LLC data block counters (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ LLC data block counters +
+ +
+ Received +
+ PDU'S bbbb +
+ Sent PDU’s dddd +
+ Missing +
+ downl PDU's ffff +
+ Re-trans +
+ uplink PDU'S hhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
bbbb GPDS FTD_SB_LLC_PDU_R R,I,O Counter for received LLC PDUs
ECV
dddd GPDS FTD_SB_LLC_PDU_S R,I,O Counter for sent LLC PDUs
ENT
ffff GPDS FTD_SB_LLC_PDU_ R,I,O Counter for detected missing or erroneous??
MISS downlink LLC PDUs
hhhh GPDS FTD_SB_LLC_PDU_R R,I,O Counter for re-transmitted uplink LLC PDUs
ESENT

Display 07.07: LLC Ciphering parameters (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ LLC ciphering parameters+
+ +
+ LSB of Kc a(8) +
+ MSB of Kc b(8) +
 SPECIFICATION 85 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ UL overflow I c(4) +
+ DL overflow I d(4) +
+ UL overflow UI e(4) +
+ DL overflow UI f(4) +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaaaaaa GPDS FTD_SB_LLC_KC1 R,I,O LSB of Kc (bits 0-31) in hex format
bbbbbbbb GPDS FTD_SB_LLC_KC2 R,I,O MSB of Kc (bits 32-63) in hex format
cccc GPDS FTD_SB_LLC_OC_I_UL R,I,O Uplink overflow counter for I frames
dddd GPDS FTD_SB_LLC_OC_I_DL R,I,O Downlink overflow counter for I frames
eeee GPDS FTD_SB_LLC_OC_UI_UL R,I,O Uplink overflow counter for UI frames
ffff GPDS FTD_SB_LLC_OC_UI_DL R,I,O Downlink overflow counter for UI
frames

Display 07.08: LLC parameters of the first SAPI (Version: 1, Status: Approved)

xx is shown in all fields if there is no LLC SAPIs activated?

+++++++++++++++++++++++++++
+ LLC parameters 1. SAPI +
+ +
+ SAPI a(2) +
+ N201-I b(4) +
+ N201-U c(4) +
+ N200 / T200 d(2) e(4) +
+ kU / kD f(3) g(3) +
+ mU h(5) +
+ mD I(5) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa GPDS FTD_SB_GPDS_SAP R,I,O The SAPI identity: 3,5,9 or 11.
I_1
bbbb GPDS FTD_SB_LLC_N201_I R,I,O The value of N201-I (maximum information field
_1 for I frames), range 140-1520.
cccc GPDS FTD_SB_LLC_N201_ R,I,O The value of N201-U (maximum information field
U_1 for U and UI frames), range 140-1520.
dd GPDS FTD_SB_LLC_N200_ R,I,O The value of N200 (maximum number of
1 retransmissions), range 1-15.
eeee GPDS FTD_SB_LLC_T200_ R,I,O The value of T200 (retransmission timeout),
1 range 1-4095.
fff GPDS FTD_SB_LLC_KU_1 R,I,O The value of kU (uplink window size), range 1-
255.
ggg GPDS FTD_SB_LLC_KD_1 R,I,O The value of kD (downlink window size), range
1-255.
 SPECIFICATION 86 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 07.09: LLC parameters of the second SAPI (Version: 1, Status: Approved)

xx is shown in all fields if there is no LLC SAPIs activated.

+++++++++++++++++++++++++++
+ LLC parameters 2. SAPI +
+ +
+ SAPI a(2) +
+ N201-I b(4) +
+ N201-U c(4) +
+ N200 / T200 d(2) e(4) +
+ kU / kD f(3) g(3) +
+ mU h(5) +
+ mD I(5) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa GPDS FTD_SB_GPDS_SAP R,I,O The SAPI identity: 3,5,9 or 11.
I_2
bbbb GPDS FTD_SB_LLC_N201_I R,I,O The value of N201-I (maximum information field
_2 for I frames), range 140-1520.
cccc GPDS FTD_SB_LLC_N201_ R,I,O The value of N201-U (maximum information field
U_2 for U and UI frames), range 140-1520.
dd GPDS FTD_SB_LLC_N200_ R,I,O The value of N200 (maximum number of
2 retransmissions), range 1-15.
eeee GPDS FTD_SB_LLC_T200_ R,I,O The value of T200 (retransmission timeout),
2 range 1-4095.
fff GPDS FTD_SB_LLC_KU_2 R,I,O The value of kU (uplink window size), range 1-
255.
ggg GPDS FTD_SB_LLC_KD_2 R,I,O The value of kD (downlink window size), range
1-255.

Display 07.10: SNDC Data counters (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ SNDC data counters +
+ +
+ Received NPDU’s b(4) +
+ Sent NPDU’s d(4) +
+ Aborted NPDU f(4) +
+ Resent NPDU’s h(4) +
+ +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 87 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
bbbb GPDS FTD_SB_SN_NPDU_RECV R,I,O Counter for received NPDUs
dddd GPDS FTD_SB_SN_NPDU_SENT R,I,O Counter for sent NPDUs
ffff GPDS FTD_SB_SN_NPDU_ABORT R,I,O Counter for aborted NPDU receptions
hhhh GPDS FTD_SB_SN_NPDU_RESENT R,I,O Counter for resent NPDUs

Display 07.11: PPP information (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PPP information +
+ +
+ PPP HDLC FCS failures +
+ bbbb +
+ PPP max receive unit +
+ dddd +
+ PPP max transmit unit +
+ ffff +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
bbbb GPDS FTD_SB_PDI_FCS_F R,I,O Counter for PPP HDLC FCS failures
AIL
dddd GPDS FTD_SB_PDI_MRU R,I,O Negotiated PPP Maximum Receive Unit Value.
ffff GPDS FTD_SB_PDI_MTU R,I,O Negotiated PPP Maximum Transmit Unit Value.

Display 07.12: ERLC Data information_1 (Version: 3.32, Status: Approved)

+++++++++++++++++++++++++++
+ ERLC Data information 1 +
+ +
+ Used MCS UL B(4) +
+ +
+ Used MCS DL d(4) +
+ +
+ Resegmentation bit f +
+ +
+ Pre-emptive bit h +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
b(4) GPDS FTD_SB_ERLC_MCS_UPLINK S R,I,O Used MCS for uplink.
Coding 1,2,3,4,5,6,7,8,9,3P,6P
d(4) GPDS FTD_SB_ERLC_MSC_DOWNL S R,I,O Used MCS for downlink
INK Coding 1,2,3,4,5,6,7,8,9,3P,6P
f GPDS FTD_SB_ERLC_RESEGMENT R,I,O Value of resegmentation bit
_BIT
h GPDS FTD_SB_ERLC_PRE_EMPTIV R,I,O Value of pre-emptive transmission bit
 SPECIFICATION 88 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 07.13: ERLC Data information_2 (Version: 3.12, Status: Approved)

+++++++++++++++++++++++++++
+ ERLC Data information 2 +
+ +
+ Used window size for UL +
+ b(5) +
+ +
+ +
+ Used window size for UL +
+ d(5) +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
bbbbb GPDS FTD_SB_ERLC_WINDOW_UP R,I,O Used window size for uplink
LINK
ddddd GPDS FTD_SB_ERLC_WINDOW_DO R,I,O Used window size for downlink
WNLIN

Display 07.14: ERLC Data counters (Version: 3.12, Status: Approved)

+++++++++++++++++++++++++++
+ ERLC Data counters +
+ +
+ MS out of memory counter+
+ b(5) +
+ +
+ +
+ MCS changes during TBF +
+ d(5) +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
 SPECIFICATION 89 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

b(5) GPDS FTD_SB_ERLC_MS_OUT_OF R,I,O MS_OUT_OF_MEMORY counter

_MEM
d(5) GPDS FTD_SB_ERLC_LINK_ADAPT R,I,O Number of MCS changes during TBF
ATIONS

Display 07.15: System status (Version: 5.0, Status: Approved)

In 2G only products, xx is shown in all counter fields.

+++++++++++++++++++++++++++
+ System status +
+ +
+ System status a(2) +
+ SMS sig req b(5) +
+ Data serv req c(5) +
+ GSM serv req d(5) +
+ Inter-sys HO e(5) +
+ Active PDP f(2) +
+ Active CID h(12) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(2) GPDS FTD_SB_GPDS_ATT S R,I,O Status of the system:
_AND_PDP G if GSM,
GP if attached to GSM and PDP context created,
U if UMTS,
UP if attached to UMTS and PDP context
created,
empty if not attached.
b(5) GPDS FTD_SB_GPDS_MSL W:D R,I,O Counter for SMS signalling service requests.
_SMS_SERV_REQ_C
OUNTER
c(5) GPDS FTD_SB_GPDS_MSL W:D R,I,O Counter for data service requests.
_DATA_SERV_REQ_
COUNTER
d(5) GPDS FTD_SB_GPDS_MSL W:D R,I,O Counter for GSM service requests.
_GSM_SERV_REQ_C
OUNTER
e(5) GPDS FTD_SB_GPDS_MSL W:D R,I,O Counter for inter-system handovers.
_INTSYS_HO_COUN
TER
f(2) GPDS FTD_SB_GPDS_CON B:D R,I,O Number of active PDP contexts, range 0-10.
TEXT_COUNT
h(12) GPDS FTD_SB_GPDS_ACTI S R,I,O Active CIDs (6 first) after each other, range 0-10
VE_CIDS for each. Example when 4 active PDP contexts: “
0 1 2 3”.

Display 07.16: Information of the selected PDP context (Version: 5.0, Status: Approved)
 SPECIFICATION 90 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

To change PDP context, perform following steps:

1. Press the Options button.
2. Select Change PDP context
3. Press the Select button.
4. “INPUT” prompt will be shown on the display, enter the PDP context identifier (CID) in display.
5. Confirm with the Ok button.

If change succeeded, the new PDP context information is displayed. If no PDP context is active, xx is
shown in all fields. In 2G only products, xx is shown in most of the fields.

+++++++++++++++++++++++++++
+ PDP context information +
+ Change PDP use options +
+ CID / SAPI a(2) b(2)+
+ NSAPI / be id c(2) d(2)+
+ Flow id/Pr lev e(3) f +
+ H Comp/D comp g h +
+ PDP context address +
+ I(3).j(3).k(3).l(3) +
+ Primary CID m(2) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
INPU GPDS FTD_SB_GPDS_CHA DW : R,I,O Context identifier (CID), range 0-10.
T NGE_CONTEXT D
a(2) GPDS FTD_SB_GPDS_CID B:D R,I,O CID of the PDP context, range 0-10.
b(2) GPDS FTD_SB_GPDS_SAPI B:D R,I,O SAPI of the PDP context: 1,3,5,7,9 or 11.
c(2) GPDS FTD_SB_GPDS_NSA B:D R,I,O NSAPI of the PDP context, range 5-15.
PI
d(2) GPDS FTD_SB_GPDS_MSL B:D R,I,O The radio bearer ID of the PDP context, range 5-
_RBID 32.
e(3) GPDS FTD_SB_GPDS_MSL B:D R,I,O The packet flow ID of the PDP context, range 0-
_PFID 127.
f GPDS FTD_SB_GPDS_MSL B:D R,I,O Radio priority level of the corresponding NSAPI,
_RPRI range 1-4.
g GPDS FTD_SB_GPDS_MSL S R,I,O Header compression to be used:
_HCOMP V - VanJacobsen (RFC1144),
D - Degermark (RFC2507),
R - RoHC (RFC3095),
otherwise 'x' is shown.
h GPDS FTD_SB_GPDS_MSL S R,I,O Data compression to be used:
_DCOMP 2 - V.42bis
4 - V.44,
otherwise 'x' is shown.
i(3) GPDS FTD_SB_GPDS_PDP B:D R,I,O First byte of the PDP address in IPv4 format. If
_ADDRESS_V4_1 IPv6 is used 'xxx' is shown.
j(3) GPDS FTD_SB_GPDS_PDP B:D R,I,O Second byte of the PDP address in IPv4 format.
_ADDRESS_V4_2 If IPv6 is used 'xxx' is shown.
k(3) GPDS FTD_SB_GPDS_PDP B:D R,I,O Third byte of the PDP address in IPv4 format. If
_ADDRESS_V4_3 IPv6 is used 'xxx' is shown.
l(3) GPDS FTD_SB_GPDS_PDP B:D R,I,O Last byte of the PDP address in IPv4 format. If
_ADDRESS_V4_4 IPv6 is used 'xxx' is shown.
m(2) GPDS FTD_SB_GPDS_REL B:D R,I,O Empty if primary context. CID of the related
 SPECIFICATION 91 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

ATED PRIM_CID primary PDP context, range 0-10, if secondary

context.

Display 07.17: QoS of the selected PDP context 1 (Version: Charlie spec)

To change PDP context, perform following steps:

1. Press the Options button.
2. Select Change PDP context
3. Press the Select button.
4. “INPUT” prompt will be shown on the display, enter the PDP context identifier (CID) in display.
5. Confirm with the Ok button.

If change succeeded, the new QoS information is displayed. If no PDP context is active, xx is shown
in all fields.

+++++++++++++++++++++++++++
+ PDP context QoS info 1 +
+ Context ID a(2) +
+ Trafic class b +
+ Erroneous SDU c +
+ Delivery order d +
+ Max SDU size e(3) +
+ Bit error rate f +
+ SDU error rate g +
+ Max bit UL/ DL h(3) I(3)+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID For Mode Description

mat
INPU GPDS FTD_SB_GPDS_CHA DW : R,I,O Context identifier (CID), range 0-10.
T NGE_CONTEXT D
a(2) GPDS FTD_SB_GPDS_CID B:D R,I,O CID of the PDP context, range 0-10.
b GPDS FTD_SB_GPDS_SM_T B:D R,I,O The traffic class, range 1-4.
RAC
c GPDS FTD_SB_GPDS_SM_D B:D R,I,O The delivery of the erroneous SDUs, range 1-3.
OES
d GPDS FTD_SB_GPDS_SM_D B:D R,I,O The delivery order, range 1-2.
ELO
e(3) GPDS FTD_SB_GPDS_SM_ B:D R,I,O Maximum SDU size, range 1-153.
MSDU
f GPDS FTD_SB_GPDS_SM_R B:D R,I,O The residual Bit Error Rate (BER), range 1-9.
BER
g GPDS FTD_SB_GPDS_SM_S B:D R,I,O The SDU error ratio, range 1-7.
DER
h(3) GPDS FTD_SB_GPDS_SM_ B:D R,I,O Maximum bit rate for uplink, range 1-254.
MBRU
i(3) GPDS FTD_SB_GPDS_SM_ B:D R,I,O Maximum bit rate for downlink, range 1-254.
MBRD
 SPECIFICATION 92 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 07.18: QoS of the selected PDP context 2 (Version: Charlie spec)

+++++++++++++++++++++++++++
+ PDP context QoS info 1 +
+ Trafic priority j +
+ Transfer delay k(2) +
+ Guar bit rate UL l(3) +
+ Guar bit rate DL m(3) +
+ Neg Rel class n +
+ Neg Del class o +
+ Neg preced calss p +
+ Peak / mean Thru q r(2)+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID For Mode Description

mat
j GPDS FTD_SB_GPDS_SM_T B:D R,I,O The traffic handling priority, range 1-3.
RHP
k(2) GPDS FTD_SB_GPDS_SM_T B:D R,I,O The transfer delay, range 1-62.
RDL
l(3) GPDS FTD_SB_GPDS_SM_ B:D R,I,O Guaranteed bit rate for uplink, range 1-254.
GBRU
m(3) GPDS FTD_SB_GPDS_SM_ B:D R,I,O Guaranteed bit rate for downlink, range 1-254.
GBRD
n GPDS FTD_SB_GPDS_SM_R B:D R,I,O The negotiated reliability class, range 1-5.
ELC
o GPDS FTD_SB_GPDS_SM_D B:D R,I,O The negotiated delay class, range 1-4.
ELC
p GPDS FTD_SB_GPDS_SM_P B:D R,I,O The negotiated precedence class, range 1-3
REC
q GPDS FTD_SB_GPDS_SM_P B:D R,I,O The negotiated peak throughput, range 1-9.
TPC
r(2) GPDS FTD_SB_GPDS_SM_ B:D R,I,O The negotiated mean throughput, range 1-31.
MTPC

Display 07.19: PDCP parameters of the selected PDP context (Version: 3.22, Status: Approved)

To change PDP context, perform following steps:

6. Press the Options button.
7. Select Change PDP context
8. Press the Select button.
9. “INPUT” prompt will be shown on the display, enter the PDP context identifier (CID) in display.
10. Confirm with the Ok button.
 SPECIFICATION 93 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

If change succeeded, new PDCP parameters are displayed. If no PDCP radio bearer is active, xx is
shown in all fields.

+++++++++++++++++++++++++++
+ PDCP parameters +
+ Radio bearer ID a +
+ PDU presense b +
+ Loss SRNS supp c +
+ Max window size d(5) +
+ Dis PDU recept e(5) +
+ Dis PDU transm f(5) +
+ S RX PDU/TX PDU g(5) +
+ T RX PDU/TX PDU i(5)j(5)+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
INPUT GPDS FTD_SB_GPDS_CHANGE_CO DW:D R,I,O Context identifier (CID), range 0-10.
NTEXT
a(2) GPDS FTD_SB_GPDS_PDCP_RBID B:D R,I,O The radio bearer ID of the PDP
context, range 5-32.
b GPDS FTD_SB_GPDS_PDCP_HEAD B:D R,I,O Indicates the presence of the PDCP
ER PDU header, range 0-1.
c GPDS FTD_SB_GPDS_PDCP_RELO B:D R,I,O Indicates whether the lossless SRNS
C relocation is supported, range 0-1.
d(5) GPDS FTD_SB_GPDS_PDCP_MAX_ W:D R,I,O Maximum window size, 0-65535.
WS
e(5) GPDS FTD_SB_GPDS_PDCP_RECV W:D R,I,O Number of discarded PDUs in
_DISC reception.
f(5) GPDS FTD_SB_GPDS_PDCP_SENT W:D R,I,O Number of discarded PDUs in
_DISC transmission.
g(5) GPDS FTD_SB_GPDS_PDCP_SEQ_ W:D R,I,O Number of PDUs received with
RECV sequence number.
h(5) GPDS FTD_SB_GPDS_PDCP_SEQ_ W:D R,I,O Number of PDUs sent with sequence
SENT number.
i(5) GPDS FTD_SB_GPDS_PDCP_PDU_ W:D R,I,O Total number of received PDUs.
RECV
j(5) GPDS FTD_SB_GPDS_PDCP_PDU_ W:D R,I,O Total number of sent PDUs.
SENT

Display 07.20: RFC2507 parameters of the selected PDP context (Version: 3.22, Status:
Approved)

To change PDP context, perform following steps:

11. Press the Options button.
12. Select Change PDP context
13. Press the Select button.
 SPECIFICATION 94 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

14. “INPUT” prompt will be shown on the display, enter the PDP context identifier (CID) in display.
15. Confirm with the Ok button.

If change succeeded, new RFC2507 parameters are displayed. If RFC2507 is not active, xx is shown in
all fields.

+++++++++++++++++++++++++++
+ PDCP parameters +
+ Radio bearer ID a(2) +
+ F_MAX_PERIOD b(5) +
+ F_MAX_TIME c(3) +
+ MAX_HEADER d(5) +
+ EXPECT_REORDING e +
+ TCP_SPACE f(3) +
+ NON_TCP_SPACE g(5) +
+ RX Pac/TX Pac h(5)i(5)+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
INPU GPDS FTD_SB_GPDS_CHA DW : R,I,O Context identifier (CID), range 0-10.
T NGE_CONTEXT D
a(2) GPDS FTD_SB_GPDS_CID B:D R,I,O CID of the PDP context, range 0-10.
b(5) GPDS FTD_SB_GPDS_RFC W:D R,I,O RFC2507 parameter F_MAX_PERIOD, range 1-
2507_MAX_PERIOD 65535.
c(3) GPDS FTD_SB_GPDS_RFC B:D R,I,O RFC2507 parameter F_MAX_TIME, range 1-
2507_MAX_TIME 255.
d(5) GPDS FTD_SB_GPDS_RFC W:D R,I,O RFC2507 parameter MAX_HEADER, range 60-
2507_MAX_HEADER 65535.
e GPDS FTD_SB_GPDS_RFC B:D R,I,O RFC2507 parameter EXPECT_REORDERING,
2507_EXP_REORD range 0-1.
f(3) GPDS FTD_SB_GPDS_RFC B:D R,I,O RFC2507 parameter TCP_SPACE, range 3-255.
2507_TCP_SPACE
g(5) GPDS FTD_SB_GPDS_RFC W:D R,I,O RFC2507 parameter NON_TCP_SPACE, range
2507_NON_TCP_SPA 3-65535.
CE
h(5) GPDS FTD_SB_GPDS_RFC W:D R,I,O Number of received context state packets.
2507_CTX_STATE_R
ECV
i(5) GPDS FTD_SB_GPDS_RFC W:D R,I,O Number of sent context state packets.
2507_CTX_STATE_S
ENT
 SPECIFICATION 95 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved
 SPECIFICATION 96 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 08: GPRS Measurement displays

Xx is shown in all the fields when the values are not available (e.g. no GPRS support in the cell, no
GPRS attach performed).

Display 08.01: Power control parameters (Version: 3.19, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Power control +
+ +
+ Alpha aaa +
+ TW / TT bb cc +
+ PSI4 / PB d eee +
+ PC channel ffff +
+ Ni value gg +
+ Gamma0-7 hh hh hh hh +
+ hh hh hh hh +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block Form Mode Description

r ID at
a(3) GSS FTD_SB_A B:D R,I,O The value of ALPHA, range 0.0-1.0.
LPHA
b(2) GSS FTD_SB_T B:D R,I,O The k value for T_AVG_W, range 0-25.
_AVG_W
c(2) GSS FTD_SB_T B:D R,I.O The k value for T_AVG_T, range 0-25.
_AVG_T
d GPD FTD_MAC B:D R,I.O The value of INT_MEAS_CHANNEL_LIST_AVAIL, range 0-
S _PSI4_BR 1. If 1, PSI4 is broadcasted. x is shown if PBCCH is not
OADCAST supported.
e(3) GSS FTD_SB_P B:D R,I.O The value of Pb, range 0 - -30 [dB]. xxx is shown if PBCCH
B is not supported.
f(4) GSS FTD_SB_P S R,I.O The value of PC_MEAS_CHAN, either BCCH or PDCH.
C_MEAS_
CHAN
g(2) GSS FTD_SB_ B:D R,I.O The k value for N_AVG_I, range 0-15.
N_AVG_I
h(2) x GSS FTD_SB_ B:D R,I.O The values of GAMMA_TN0, GAMMA_TN1,…,
8 GAMMA_T GAMMA_TN7, range 0-62 [dB] on each. xx is shown in
N0..7 place of unused time slots. (Thus, in packet idle mode, all of
them are xx.)
 SPECIFICATION 97 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 08.02: The previous channel quality report (Version: 3.20, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Prev channel quality +
+ +
+ +
+ Dlack/RESreq aaaaaaa +
+ C value bb +
+ RX quality c +
+ Var value dd +
+ IF0-7 hh hh hh hh +
+ hh hh hh hh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(7) GPDS FTD_SB_M S R,I,O DL_ACK if the previous channel quality report was sent
AC_QREP_ in PACKET DOWNLINK ACK/NACK message.
SENT_IN RES_REQ if the previous channel quality report was
sent in PACKET RESOURCE REQUEST
b(2) GPDS FTD_SB_M B:D R,I,O The reported C value, range 0-63.
AC_C_VAL
UE
c GPDS FTD_SB_M B:D R,I,O The reported RXQUAL value, downlink quality, range 0-
AC_RXQUA 7. If the previous channel quality report was included in
L PACKET RESOURCE REQUEST, x is shown.
d(2) GPDS FTD_SB_M B:D R,I.O The reported SIGN_VAR value, range 0-63. xx is shown
AC_SIGN_V if the parameter was not included in the channel quality
AR report (in two-phase access).
h(2) x 8 GPDS FTD_SB_M B:D R,I.O The reported I_LEVEL_TN0,
AC_QREP_I I_LEVEL_TN1,…,I_LEVEL_TN7 values, range 0-63 on
_TN0..7 each. xx is shown if the corresponding interference level
was not reported.

Display 08.03: NC and EM parameters (Version: 1, Status: REJECTED)

Data Display:

+++++++++++++++++++++++++++
+ NC and EM parameters +
+ +
+ NC mode a +
+ N I T b C d +
+ PSI5 eeee +
+ Ord/Type/Period f g h +
+ P/O iiii +
+ NCC jjj +
 SPECIFICATION 98 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ IFfr kkk +
+++++++++++++++++++++++++++

xx is shown in all fields if PBCCH is not supported and if neither PACKET MEAS ORDER nor
PACKET CELL CHANGE ORDER has been received.

Abbr. Server Sub Block Form Mode Description

ID at
a R,I,O The value of NETWORK_CONTROL_ORDER, range 0-2.
b The value of NC_NON_DRX_PERIOD, range 0-7.
C The value of NC_REPORTING_PERIOD_I, range 0-7.
d The value of NC_REPORTING_PERIOD_T, range 0-7.
eeee PSI5 if the current NC parameters were received in PSI5
message.
ORDE if the current NC parameters were received in
PACKET MEAS ODER or PACKET CELL CHANGE
ORDER.
f The value of EXT_MEASUREMENT_ORDER, range 0-1.
g The value of EXT_REPORTING_TYPE, range 1-3.
h The value of EXT_REPORTING_PERIOD, range 0-7.
iiii PSI5 if the current EM parameters were received in PSI5
message.
ORDE if the current EM parameters were received in
PACKET MEAS ODER or PACKET CELL CHANGE
ORDER.
jjj The value of NCC_PERMITTED, range 0-255. xxx is
shown if EXT_REPORTING_TYPE is not type 2.
kkk The carrier number (in decimal) where INT_FREQUENCY
refers. xxx is shown if INT_FREQUENCY is not
broadcasted (optional).

Display 08.04: The previous NC report, part 1 (Version: 1, Status: REJECTED)

Data Display:

+++++++++++++++++++++++++++
+ Prev NC report part1 +
+ +
+ RxL / IFLev aa bb +
+ +
+ Carrier BSIC RxLevel +
+ 1 ccc dd ee +
+ 2 ccc dd ee +
+ 3 ccc dd ee +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 99 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

If the previous NC measurement report included less than 3 measurement results, xx is shown in the
corresponding rows.

1.row 1.neighbor information

2.row 2.neighbor information
3.row 3.neighbor information

Abbr. Server Sub Block Form Mode Description

ID at
aa R,I,O The value of RXLEV_SERVING_CELL in the previous
transmitted NC measurement report (PACKET
MEASUREMENT REPORT), range 0-63.
bb The value of INTERFERENCE_SERVING_CELL, range 0-
63. xx is shown if the interference value was not reported.
ccc Carrier number in decimal.
dd BSIC value. xx is shown if BSIC was not reported.
ee RXLEVEL value, range 0-63 or in dBm.

Display 08.05: The previous NC report, part 2 (Version: 1, Status: REJECTED)

Data Display:

+++++++++++++++++++++++++++
+ Prev NC report part2 +
+ +
+ +
+ Carrier BSIC RxLevel +
+ 4 ccc dd ee +
+ 5 ccc dd ee +
+ 6 ccc dd ee +
+ +
+ +
+++++++++++++++++++++++++++

If the previous NC measurement report included less than 6 measurement results, xx is shown in the
corresponding rows.

4.row 4.neighbor information

5.row 5.neighbor information
6.row 6.neighbor information
 SPECIFICATION 100 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Forma Mode Description

t
Ccc R,I,O Carrier number in decimal.
Dd BSIC value. xx is shown if BSIC was not reported.
Ee RXLEVEL value, range 0-63.

Display 08.06: The previous EM report, part 1 (Version: 1, Status: REJECTED)

Data Display:

+++++++++++++++++++++++++++
+ Prev EM report part1 +
+ +
+ +
+ Carrier BSIC RxLevel +
+ 1 ccc dd ee +
+ 2 ccc dd ee +
+ 3 ccc dd ee +
+ 4 ccc dd ee +
+ +
+++++++++++++++++++++++++++

If the previous EM measurement report included less than 4 measurement results, xx is shown in the
corresponding rows.

1.row 1.neighbor information

2.row 2.neighbor information
3.row 3.neighbor information
4.row 4.neighbor information

Abbr. Server Sub Block ID Forma Mode Description

t
ccc R,I,O Carrier number in decimal.
dd BSIC value. xx is shown if BSIC was not reported.
ee RXLEVEL value, range 0-63.

Display 08.07: The previous EM report, part 2 (Version: 1, Status: REJECTED)

Data Display:

+++++++++++++++++++++++++++
+ Prev EM report part2 +
+ +
 SPECIFICATION 101 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ +
+ Carrier BSIC RxLevel +
+ 5 ccc dd ee +
+ 6 ccc dd ee +
+ +
+ IFLevel0-7 hh hh hh hh +
+ hh hh hh hh +
+++++++++++++++++++++++++++

If the previous EM measurement report included less than 6 measurement results, xx is shown in the
corresponding rows.

5.row 5.neighbor information

6.row 6.neighbor information

Abbr. Server Sub Block Form Mode Description

ID at
ccc R,I,O Carrier number in decimal.
dd BSIC value. xx is shown if BSIC was not reported.
ee RXLEVEL value, range 0-63.
hh x 8 The reported I_LEVEL_TN0,
I_LEVEL_TN1,…,I_LEVEL_TN7 values, range 0-63 on
each. xx is shown if the corresponding interference level
was not reported. in dBm if possible

Display 08.08: Downlink power control parameters (Version: 1, Status: REJECTED)

Data Display:

+++++++++++++++++++++++++++
+ Downlink power control +
+ +
+ BTS PWR CTRL a +
+ PO value bb +
+ PR value (A/B) c +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

xx is shown in the fields if there is no TBF active.

Abbr. Server Sub Block ID Forma Mode Description

t
a R,I,O The value of BTS_PWR_CTRL_MODE, either A or B
bb The value of P0, range 0-30 [dB].
c The value of PR mode:
A: PR Mode A is used
 SPECIFICATION 102 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

B: PR Mode B is used
 SPECIFICATION 103 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 09: GPRS Test counter displays

Display 09.02: TBF counters (Version: 5.0, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ TBF counters +
+ +
+ UL packet idle aaaaa +
+ UL TBF idle bbbbb +
+ UL packet tr ccccc +
+ UL TBF tr ddddd +
+ +
+ DL TBF idle fffff +
+ UL abnormal hhhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(5) GPDS FTD_SB_M W:D R,I,O Counter for UL TBF attempts in packet idle mode
AC_UL_TBF
_IDLE_ATT
EMPT
b(5) GPDS FTD_SB_RL W:D R,I,O Counter for successful UL TBFs, established in packet
C_UL_TBF_ idle mode
IDLE_SUCC
c(5) GPDS FTD_SB_M W:D R,I,O Counter for UL TBF attempts in packet transfer mode
AC_UL_TBF
_TRANS_AT
TEMPT
d(5) GPDS FTD_SB_RL W:D R,I,O Counter for successful UL TBFs, established in packet
C_UL_TBF_ transfer mode
TRANS_SU
CC
f(5) GPDS FTD_SB_M W:D R,I,O Counter for DL TBF establishments in packet idle mode
AC_DL_TBF
_COUNTER
h(5) GPDS FTD_SB_RL W:D R,I,O Counter for UL TBF abnormal releases, any reason
C_UL_TBF_
ABNORM_R
EL
 SPECIFICATION 104 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 09.10: GPRS attach and detach counters (Version: 5.0, Status:Approved)

Data Display:

+++++++++++++++++++++++++++
+ GPRS attach and detach +
+ +
+ Attach failure aa +
+ Attach attemps bbb +
+ Attach succeeded cccc +
+ NI detach cause hh +
+ NI detach counter iii +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(2) GPDS FTD_SB_G B:H R,I,O Cause of the last attach failure
MM_ATTAC
H_FAIL_CA
USE
b(3) GPDS FTD_SB_G W:D R,I,O Counter for the attach attempts
MM_ATTAC
H_ATTEMP
T
c(4) GPDS FTD_SB_G W:D R,I,O Counter for the succeededl attachs
MM_ATTAC
H_OK
h(2) GPDS FTD_SB_G B:H R,I,O Cause of the last network initiated detach
MM_NTW_I
NIT_DET_C
AUSE
i(3) GPDS FTD_SB_G W:D R,I,O Counter for network initiated detach
MM_NTW_I
NIT_DETAC
H
 SPECIFICATION 105 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 09.11: Periodic routing area update counters (Version: 5.0, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Periodic routing area +
+ update counters +
+ +
+ RA update cause aa +
+ RAU attemps bbbb +
+ RAU succeeded cccc +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(2) GPDS FTD_SB_G B:H R,I,O Cause of the last periodic routing area update failure
MM_PRAU_
FAIL_CAUS
E
b(4) GPDS FTD_SB_G W:D R,I,O Counter for the periodic RAU attempts
MM_PRAU_
ATTEMPT
c(4) GPDS FTD_SB_G W:D R,I,O Counter for the succeeded periodic RAUs
MM_PRAU_
OK

Display 09.12: Routing area update counters (Version: 5.0, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Routing area update +
+ counters +
+ +
+ RA update cause aa +
+ RAU attemps bbbb +
+ RAU succeeded cccc +
+ +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 106 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block Form Mode Description

ID at
a(2) GPDS FTD_SB_G B:H R,I,O Cause of the last routing area update failure
MM_RAU_F
AIL_CAUSE
b(4) GPDS FTD_SB_RA W:D R,I,O Counter for the RAU attempts
U_ATTEMP
T
c(4) GPDS FTD_SB_RA W:D R,I,O Counter for the succeeded RAUs
U_OK

Display 09.13: PDP context counters (Version: 5.0, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ PDP context counters +
+ +
+ PDP act failure aa +
+ PDP act attemps bbb +
+ PDP succeeded ccc +
+ PDP MS init deact gg +
+ PDP net init deact jj +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(2) GPDS FTD_SB_S B:H R,I,O Cause of the last MS initiated PDP context activation failure
M_MO_PDP
_FAIL_CAU
SE
b(3) GPDS FTD_SB_S W:D R,I,O Counter for the MS initiated PDP context activation
M_MO_PDP attempts
_ATTEMPT
c(3) GPDS FTD_SB_S W:D R,I,O Counter for the succeeded MS initiated PDP context
M_MO_PDP activations
_OK
 SPECIFICATION 107 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

g(2) GPDS FTD_SB_S B:H R,I,O Cause of the last MS initiated PDP context deactivation
M_MO_PDP
_DEAC_CA
USE
j(2) GPDS FTD_SB_S B:H R,I,O Cause of the last Network initiated PDP context
M_MT_PDP deactivation
_DEAC_CA
USE

Display 09.14: SMS over GPRS counters (Version: 5.0, Status: Approved)

The values in this display concern only SMS transferred via GPRS. Otherwise the SMS counters in
GSM displays are valid.

Data Display:

+++++++++++++++++++++++++++
+ SMS over GPRS counters +
+ +
+ Send failure aa +
+ MO SMS attemps bbb +
+ MO SMS send OK ccc +
+ Receive failure dd +
+ MT SMS attemps eee +
+ MT SMS receive OK fff +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block Form Mode Description

ID at
a(2) GSS FTD_SB_S B:H R,I,O Reason of last sending failure
MS_SEND_
FAIL_CAUS
E_GPRS
b(3) GSS FTD_SB_S W:D R,I,O Count of MO short message attempts via GPRS
MS_MO_AT
T_GPRS
c(3) GSS FTD_SB_S W:D R,I,O Count of succeeded MO short message sendings
 SPECIFICATION 108 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

MS_MO_GP
RS_OK
d(2) GSS FTD_SB_S B:H R,I,O Reason of last receiving failure
MS_REC_F
AIL_CAUSE
_GPRS
e(3) GSS FTD_SB_S W:D R,I,O Count of MT short message attempts via GPRS
MS_MT_AT
T_GPRS
f(3) GSS FTD_SB_S W:D R,I,O Count of succeeded MT short message receptions
MS_MT_GP
RS_OK

Display 09.17: MS initiated cell re-selection counters (Version: 5.0, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ MS init cell reselection+
+ counters +
+ +
+ CCCH => CCCH aaaa +
+ CCCH => PCCCH cccc +
+ PCCCH => CCCH eeee +
+ PCCCH => PCCCH gggg +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block ID Forma Mod Description

r t e
a(4) GPDS FTD_SB_MAC_ W:D R,I,O Counter for cell re-selection attempts from CCCH to
RESEL_C_C CCCH in NC0 or NC1 mode
c(4) GPDS FTD_SB_MAC_ W:D R,I,O Counter for cell re-selection attempts from CCCH to
RESEL_C_P PCCCH in NC0 or NC1 mode
e(4) GPDS FTD_SB_MAC_ W:D R,I.O Counter for cell re-selection attempts from PCCCH to
RESEL_P_C CCCH in NC0 or NC1 mode
g(4) GPDS FTD_SB_MAC_ W:D R,I,O Counter for cell re-selection attempts from PCCCH to
RESEL_P_P PCCCH in NC0 or NC1 mode
 SPECIFICATION 109 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 09.18: Network initiated cell re-selection counters (Version: 5.0, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Network init cell +
+ reselction counters +
+ +
+ CCCH =>CCCH aaaa bbbb +
+ CCCH =>PCCCH cccc dddd +
+ PCCCH =>CCCH eeee ffff +
+ PCCCH =>PCCCH gggg hhhh +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block ID Forma Mode Description

r t
a(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for network commanded cell re-selection
S _C_C_ATT attempts from CCCH to CCCH
b(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for succeeded network commanded cell
S _C_C_OK re-selections from CCCH to CCCH
c(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for network commanded cell re-selection
S _C_P_ATT attempts from CCCH to PCCCH
d(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for succeeded network commanded cell
S _C_P_OK re-selections from CCCH to PCCCH
e(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for network commanded cell re-selection
S _P_C_ATT attempts from PCCCH to CCCH
f(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for succeeded network commanded cell
S _P_C_OK re-selections from PCCCH to CCCH
g(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for network commanded cell re-selection
S _P_P_ATT attempts from PCCCH to PCCCH
h(4) GPD FTD_SB_MAC_PCCO W:D R,I,O Counter for succeeded network commanded cell
S _P_P_OK re-selections from PCCCH to PCCCH
 SPECIFICATION 110 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 10: GSM DSP displays

Display 10.01: DSP Data Display 1 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ DSP data display 1 +
+ +
+ 1 aaaa +
+ 2 bbbb +
+ 3 cccc +
+ 4 dddd +
+ 5 eeee +
+ 6 ffff +
+ 7 8 gggg hhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
aaaa GSM_DSP FTD_SB_DSP_DATA_1 R DSP specific data in hex format
bbbb GSM_DSP FTD_SB_DSP_DATA_2 R DSP specific data in hex format
cccc GSM_DSP FTD_SB_DSP_DATA_3 R DSP specific data in hex format
dddd GSM_DSP FTD_SB_DSP_DATA_4 R DSP specific data in hex format
eeee GSM_DSP FTD_SB_DSP_DATA_5 R DSP specific data in hex format
ffff GSM_DSP FTD_SB_DSP_DATA_6 R DSP specific data in hex format
gggg GSM_DSP FTD_SB_DSP_DATA_7 R DSP specific data in hex format
hhhh GSM_DSP FTD_SB_DSP_DATA_8 R DSP specific data in hex format

These values are updated 5-10 times/second.

Display 10.02: DSP Data Display 2 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ DSP data display 2 +
+ +
+ 9 aaaa +
+ 10 bbbb +
+ 11 cccc +
+ 12 dddd +
+ 13 eeee +
+ 14 ffff +
+ 15 16 gggg hhhh +
+++++++++++++++++++++++++++
 SPECIFICATION 111 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Forma Mode Description

t
aaaa GSM_DSP FTD_SB_DSP_DATA_9 R DSP specific data in hex format
bbbb GSM_DSP FTD_SB_DSP_DATA_10 R DSP specific data in hex format
cccc GSM_DSP FTD_SB_DSP_DATA_11 R DSP specific data in hex format
dddd GSM_DSP FTD_SB_DSP_DATA_12 R DSP specific data in hex format
eeee GSM_DSP FTD_SB_DSP_DATA_13 R DSP specific data in hex format
ffff GSM_DSP FTD_SB_DSP_DATA_14 R DSP specific data in hex format
gggg GSM_DSP FTD_SB_DSP_DATA_15 R DSP specific data in hex format
hhhh GSM_DSP FTD_SB_DSP_DATA_16 R DSP specific data in hex format

These values are updated 5-10 times/second.

Display 10.03: DSP Data Display 3 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ DSP data display 3 +
+ +
+ 17 aaaa +
+ 18 bbbb +
+ 19 cccc +
+ 20 dddd +
+ 21 eeee +
+ 22 ffff +
+ 23 24 gggg hhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
aaaa GSM_DSP FTD_SB_DSP_DATA_17 R DSP specific data in hex format
bbbb GSM_DSP FTD_SB_DSP_DATA_18 R DSP specific data in hex format
cccc GSM_DSP FTD_SB_DSP_DATA_19 R DSP specific data in hex format
dddd GSM_DSP FTD_SB_DSP_DATA_20 R DSP specific data in hex format
eeee GSM_DSP FTD_SB_DSP_DATA_21 R DSP specific data in hex format
ffff GSM_DSP FTD_SB_DSP_DATA_22 R DSP specific data in hex format
gggg GSM_DSP FTD_SB_DSP_DATA_23 R DSP specific data in hex format
hhhh GSM_DSP FTD_SB_DSP_DATA_24 R DSP specific data in hex format

These values are updated 5-10 times/second.

 SPECIFICATION 112 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 10.04: FER measuments for sub ch0: REAL, FULL and SUB values (Version: 3.24, Status:
Approved)

Data Display:

+++++++++++++++++++++++++++
+ FER meas for sub ch0 +
+ +
+ FER real aa +
+ Correct FACCH bb +
+ Erroneous TCH cc +
+ Erroneous FACCH dd +
+ Erroneous Full ff +
+ Used frames gg +
+ Erroneous frames hh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
a(2) GSM_DSP FTD_SB_DSP_DATA_25 B:D R,I,O FER REAL, a counter for correct
frames including TCH, FACCH,
SACCH
b(2) GSM_DSP FTD_SB_DSP_DATA_26 B:D R,I,O FER REAL, a counter for correct
FACCH frames
c(2) GSM_DSP FTD_SB_DSP_DATA_27 B:D R,I,O FER REAL, a counter for
erroneous TCH frames
d(2) GSM_DSP FTD_SB_DSP_DATA_28 B:D R,I,O FER REAL, a counter for
erroneous FACCH frames
f(2) GSM_DSP FTD_SB_DSP_DATA_29 B:D R,I,O FER FULL, a counter for
erroneous frames including
TCH, SACCH, FACCH and SID
frames
g(2) GSM_DSP FTD_SB_DSP_DATA_30 B:D R,I,O FER SUB, a counter for used
frames
h(2) GSM_DSP FTD_SB_DSP_DATA_31 B:D R,I,O FER SUB, a counter for
erroneous frames

These values are updated for every 480ms (One SACCH multiframe)
 SPECIFICATION 113 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 10.05: FER measuments for sub ch1: REAL, FULL and SUB values (Version: 3.25, Status:
Approved)

Data Display:

+++++++++++++++++++++++++++
+ FER meas for sub ch1 +
+ +
+ FER real aa +
+ Correct FACCH bb +
+ Erroneous TCH cc +
+ Erroneous FACCH dd +
+ Erroneous Full ff +
+ Used frames gg +
+ Erroneous frames hh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
a(2) GSM_DSP FTD_SB_DSP_DATA_32 B:D R,I,O FER REAL, a counter for correct
frames including TCH, FACCH,
SACCH
b(2) GSM_DSP FTD_SB_DSP_DATA_33 B:D R,I,O FER REAL, a counter for correct
FACCH frames
c(2) GSM_DSP FTD_SB_DSP_DATA_34 B:D R,I,O FER REAL, a counter for
erroneous TCH frames
d(2) GSM_DSP FTD_SB_DSP_DATA_35 B:D R,I,O FER REAL, a counter for
erroneous FACCH frames
f(2) GSM_DSP FTD_SB_DSP_DATA_36 B:D R,I,O FER FULL, a counter for
erroneous frames including
TCH, SACCH, FACCH and SID
frames
g(2) GSM_DSP FTD_SB_DSP_DATA_37 B:D R,I,O FER SUB, a counter for used
frames
h(2) GSM_DSP FTD_SB_DSP_DATA_38 B:D R,I,O FER SUB, a counter for
erroneous frames

These values are updated for every 480ms (One SACCH multiframe)
 SPECIFICATION 114 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 10.06: FER measuments for sub ch2: REAL, FULL and SUB values (Version: 3.25, Status:
Approved)

Data Display:

+++++++++++++++++++++++++++
+ FER meas for sub ch2 +
+ +
+ FER real aa +
+ Correct FACCH bb +
+ Erroneous TCH cc +
+ Erroneous FACCH dd +
+ Erroneous Full ff +
+ Used frames gg +
+ Erroneous frames hh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
a(2) GSM_DSP FTD_SB_DSP_DATA_39 B:D R,I,O FER REAL, a counter for correct
frames including TCH, FACCH,
SACCH
b(2) GSM_DSP FTD_SB_DSP_DATA_40 B:D R,I,O FER REAL, a counter for correct
FACCH frames
c(2) GSM_DSP FTD_SB_DSP_DATA_41 B:D R,I,O FER REAL, a counter for
erroneous TCH frames
d(2) GSM_DSP FTD_SB_DSP_DATA_42 B:D R,I,O FER REAL, a counter for
erroneous FACCH frames
f(2) GSM_DSP FTD_SB_DSP_DATA_43 B:D R,I,O FER FULL, a counter for
erroneous frames including
TCH, SACCH, FACCH and SID
frames
g(2) GSM_DSP FTD_SB_DSP_DATA_44 B:D R,I,O FER SUB, a counter for used
frames
h(2) GSM_DSP FTD_SB_DSP_DATA_45 B:D R,I,O FER SUB, a counter for
erroneous frames

These values are updated for every 480ms (One SACCH multiframe)
 SPECIFICATION 115 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 11: CDSP GSM AMR displays

Display 11.01: AMR1:Information of the Active Mode Set (Version: 3.16, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Channel type aaaa +
+ Active mode set bbbb +
+ Treshold 1 ccc +
+ Hysteresis 1 dd +
+ ICMI / ICM e f +
+ Treshold 2/3 ggg jjj +
+ Hysteresis 2/3 hh kk +
+ RATSCCH ii +
+ Noise suppression l +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
a(4) GSS FTD_SB_TYPE_OF_CURR_ R Channel type
CH
b(4) GSM_ FTD_SB_AMR1_MODESET R Active codec mode set , mode
DSP numbers in ACS are shown as digits
0 = 4.75
1 = 5.15
2 = 5.9
3 = 6.7
4 = 7.4
5 = 7.95
6 = 10.2
7 = 12.2

(1-4 digit hex without leading zeros)

c(3) GSM_ FTD_SB_AMR1_TH1 R first threshold, 999 if not in use
DSP
d(2) GSM_ FTD_SB_AMR1_HYS1 R first hysteresis, 99 if not in use
DSP
e GSM_ FTD_SB_AMR1_ICMI R ICMI (Initial codec mode indicator)
DSP 0=not signalled. 1=signalled.
f GSM_ FTD_SB_AMR1_ICM R Initial codec mode (ICM)
DSP If ICMI=0 mode selected by implicit
rule
If ICMI=1 signalled start mode used
(shown as absolute mode 0-7)
g(3) GSM_ FTD_SB_AMR1_TH2 R Second threshold, 999 if not in use
DSP
h(2) GSM_ FTD_SB_AMR1_HYS2 R Second hysteresis, 99 if not in use
DSP
i(2) GSM_ FTD_SB_AMR1_RATSCCH R Count RATSCCH messages, truncated
DSP (wrap around overflow) to 8 bits (print
two digit hex value)
Counter is reset at call setup and HO.
 SPECIFICATION 116 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

j(3) GSM_ FTD_SB_AMR1_TH3 R third threshold, 999 if not in use

DSP
k(2) GSM_ FTD_SB_AMR1_HYS3 R third hysteresis, 99 if not in use
DSP

l GSM_ FTD_SB_AMR1_NSCB R Noise Suppression Control bit:

DSP 0=noise suppression can be used;
1=noise suppression is turned off

Data display contains the information from MS multirate information signalling. From 8 possible
speech codec modes at most 4 belongs to active codec mode set. Active codecs are shown in display
using mode numbers which are shown as digits (0..7). Modeset display has that many digits as there
are modes in active set (1–4). Highest mode is shown left so that also mode 0, if included in the ACS,
is shown properly.

In addition to active codec mode set display shows thresholds and hysteresis values for mode changes
according link quality. With 4 modes in active mode set three threshold/hysteresis values are needed.
Number is always 1 less than number of codecs in mode set. If number of active modes is less than 4
unused threshold and hysteresis values are filled with 9's.

Even though the information needed for display is known by L3 on call setup RATSCCH signalling
may override all values. That is why display information is always fetched from DSP.

Display 11.02: AMR2: Information of the mode control (Version: 3.16, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Mode up/downlink a b +
+ Rx level/quality ccc d +
+ Channel type eeee +
+ Mode command ffff +
+ Mode command gggggggg +
+ Mode ind hhhh +
+ Mode ind iiiiiiii +
+ Mode request jjjj +
+ Mode request kkkkkkkk +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Format Mode Description

.
a GSM_DS FTD_SB_AMR_UL_MODE R Current absolute uplink mode
P within modeset (0-7)
b GSM_DS FTD_SB_AMR_DL_MODE R Current absolute downlink
P mode within modeset (0-7)
c(3) GSS FTD_SB_RX_LEVEL R Rx level in dBm, minus sign not
shown if <=-100
d GSS FTD_SB_RX_QUALITY R Rx quality (sub), range is 0 - 7
 SPECIFICATION 117 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

e(4) GSS FTD_SB_TYPE_OF_CURR_C R Channel type

H
f(4) GSM_DS FTD_SB_AMR2_MODE_CMD R mode command history(Hex)
P _HI
g(8) GSM_DS FTD_SB_AMR2_MODE_CMD R mode command history (Hex)
P _LO
h(4) GSM_DS FTD_SB_AMR2_MODE_IND_ R mode indication downlink
P DL_HI history (Hex)
i(8) GSM_DS FTD_SB_AMR2_MODE_IND_ R mode indication downlink
P DL_LO history (Hex)
j(4) GSM_DS FTD_SB_AMR2_MODE_REQ R mode request history (Hex)
P _HI
k(8) GSM_DS FTD_SB_AMR2_MODE_REQ R mode request history (Hex)
P _LO

First line shows in compact form current channel type and basic quality information
including up and downlink AMR modes. All information in the first row is available also from
Display 01.01

Three history lines are used to print mode commands, mode indication to downlink
direction and mode requests. Mode indication to uplink is not that interesting as it reflects
mode commands after short delay. Mode requests might differ from mode indications
downlink as BTS is not required to obey mode request. It should be noted that mode
information in history lines in FTD is shown using absolute modes (0–7) even though in
actual inband transmission relative value within mode set is used (0–3).

With update rate 480 ms each digit in display corresponds mode related commands /
indications in history.

DSP history algorithm can be modified to maintain history as different averages on the
basis of the future needs without changing FTD display specification. See also executive
Display 11.04: AMR4: Control AMR FTD data pre processing (Version: 1, Status:
Approved)

Display 11.03: AMR3: Information of the link quality estimation (Version: 3.16, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Mode up/down a b +
+ Rx level/quality ccc d +
+ Channel type eeee +
+ Link quality est FFff +
+ Frame erasure% GGggg +
+ Fast fading HHhh +
+ Slow fading IIii +
+ Fading comp Jj +
+ Mode regs kkkk llllllll +
+++++++++++++++++++++++++++
 SPECIFICATION 118 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
a GSM_DSP FTD_SB_AMR_UL_MODE R Current absolute uplink
mode (0-7)
b GSM_DSP FTD_SB_AMR_DL_MODE R Current absolute
downlink mode (0-7)
c(3) GSS FTD_SB_RX_LEVEL R Rx level in dBm,
minus sign not shown if
<=-100
d GSS FTD_SB_RX_QUALITY R Rx quality (sub), range is
0-7
e(4) GSS FTD_SB_TYPE_OF_CURR_C R Channel type
H
FFff GSM_DSP FTD_SB_AMR3_LQE R Current link quality
estimate (dB) (floating
point number)
GGgg GSM_DSP FTD_SB_AMR3_FRAME_ERA R frame erasure %
g SURE (floating point number)
HHhh GSM_DSP FTD_SB_AMR3_FAST_FAD_F R Output of the fast fading
ILTER filter (floating point
number)
IIii GSM_DSP FTD_SB_AMR3_SLOW_FAD_ R slow fading filter output
FILTER (floating point number)
Jj GSM_DSP FTD_SB_AMR3_FAD_COMP R fading compensation
factor
k(4) GSM_DSP FTD_SB_AMR2_MODE_REQ_ R mode request history
HI (Hex)
l(8) GSM_DSP FTD_SB_AMR2_MODE_REQ_ R mode request history
LO (Hex)

First line is same as used in 'Display 11.02: AMR2: Information of the mode control
(Version: 3.16, Status: Approved)'.

With update rate 480 ms each digit in display corresponds mode related commands /
indication in history.

FFff, GGggg, HHhh, IIii and Jj represent floating point values. Decimal part is marked with lower case
letters in this specification and decimal point is not printed
 SPECIFICATION 119 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 11.04: AMR4: Control AMR FTD data pre processing (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ AMR FTD control +
+ +
+ XXXX +
+ +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
INPUT GSM_DSP FTD_SB_AMR4_CTRL_ DW:H R Control word for DSP for controlling
WORD pre processing of AMR mode
control related field test displays.
XXXX GSM_DSP FTD_SB_AMR4_CTRL_ R Control word for DSP for controlling
DISP pre processing of AMR mode
control related field test displays.

When display is selected, control word can be edited. Keyboard is in "text"-mode, so hex numbers 0-F
can be written. After editing of the control word is completed, request is sent to DSP.

Display 11.05: AMR5: Control AMR algorithms (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ AMR algorithm control +
+ +
+ XXXX +
+ +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 120 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
INPUT GSM_DSP FTD_SB_AMR5_CTRL_WOR DW:H R Control word for DSP for
D controlling AMR algorithms.
XXXX GSM_DSP FTD_SB_AMR5_CTRL_ALG R Control word for DSP for
O controlling AMR algorithms.

When display is selected, control word can be edited. Keyboard is in "text"-mode, so hex numbers 0-F
can be written. After editing of the control word is completed, request is sent to DSP.
 SPECIFICATION 121 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 12: CDSP SW Platform

Display 12.01: CDSP version and date (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ CDSP version and date +
+ +
+ Version aaaaaaaaaaaa +
+ Version bbbbbbbbbbbb +
+ Version cccccccccccc +
+ Date dddddd +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
a(12) ADSP_CO FTD_SB_ADSP_VERSION S R CDSP version string
RE _1
b(12) ADSP_CO FTD_SB_ADSP_VERSION S R CDSP version string
RE _2
c(12) ADSP_CO FTD_SB_ADSP_VERSION S R CDSP version string
RE _3
d(6) ADSP_CO FTD_SB_ADSP_VERSION S R CDSP version date. Format: ddmmyy
RE _DATE

Display 12.02: Reset display (Version: 1, Status: Approved)

With this display all counters and error codes in this group can be reset.

Note: Does not reset PPCs

Data Display:

+++++++++++++++++++++++++++
+ Reset counters +
+ +
+ +
+ +
+ +
+ +
+ +
+ +
+ +
 SPECIFICATION 122 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
EXE MON FTD_SB_ADSP_CLEAR_C N/A R Clears all counters and error codes in
NT this group. Note! This is not resetting
any PPC counters.

Display 12.03: CDSP error and reset counters and MCU reset time (Version: 3.13, Status:
Approved)

This display has counters for MCU originated CDSP resets, CDSP originated CDSP resets
(fatal CDSP errors) and non-fatal CDSP errors. The display also holds the time of the last
MCU originated CDSP reset.

Data Display:

+++++++++++++++++++++++++++
+ CDSP error and reset +
+ and MCU reset time +
+ +
+ MCU resets aaaa +
+ Fatal CDSP bbbb +
+ Non fatal CDSP cccc +
+ MCU reset time +
+ ddddddddddd +
+ +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block ID Forma Mod Description

r t e
a(4) MON FTD_SB_PPC_MCU_GEN_ADS W:D R Number of MCU originated CDSP
P_RESET resets.
b(4) MON FTD_SB_PPC_ADSP_ORI_RES W:D R Number of CDSP originated CDSP
ETS_TOTAL resets (fatal CDSP errors).
c(4) MON FTD_SB_PPC_ADSP_NON_FA W:D R Number of non-fatal CDSP errors.
TAL_ERRORS_TOTAL
d(11) MON FTD_SB_ADSP_MCU_RESET_ S R Date and time of the last MCU
DATE originated CDSP reset. Format:
ddmmyy hhmm

Note! These are not PPC counters.

 SPECIFICATION 123 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 12.04: Counters for specific CDSP non-fatal errors (Version: 1, Status: Approved)

This display holds information about specific non-fatal errors in the CDSP.

Data Display:

+++++++++++++++++++++++++++
+ Specific non-fatal CDSP +
+ +
+ CDSP unrec aaaa +
+ Signal error bbbb +
+ Res Res cccc dddd +
+ Res Res eeee ffff +
+ Res Res gggg hhhh +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

t e
a(4) ADSP_CORE FTD_SB_ADSP_SPECIFIC_ERR W:D R Counter for unrecognised
_CNT_1 messages received by
the CDSP.
b(4) ADSP_CORE FTD_SB_ADSP_SPECIFIC_ERR W:D R Counter for errors when a
_CNT_2 signal is meant for its
receiving process, but in
different state of the
process.
c(4) ADSP_CORE FTD_SB_ADSP_SPECIFIC_ERR W:D R Reserved.
_CNT_3
d(4) ADSP_CORE FTD_SB_ADSP_SPECIFIC_ERR W:D R Reserved.
_CNT_4
e(4) ADSP_CORER FTD_SB_ADSP_SPECIFIC_ERR W:D R Reserved.
_CNT_5
f(4) ADSP_CORE FTD_SB_ADSP_SPECIFIC_ERR W:D R Reserved.
_CNT_6
g(4) ADSP_CORE FTD_SB_ADSP_SPECIFIC_ERR W:D R Reserved.
_CNT_7
h(4) ADSP_CORE FTD_SB_ADSP_SPECIFIC_ERR W:D R Reserved.
_CNT_8

Note! These counters are not PPC counters.

 SPECIFICATION 124 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 12.05: CDSP fatal error codes (Version: 3.13, Status: Approved)

This display holds four last fatal error codes. The display works in a FIFO principle. When a
new error occurs all the errors are moved forward and if there are errors more than four,
the oldest error code is removed. There are separate queues for fatal and non-fatal error
codes. Also the ID of the last executed process is displayed after the error code. Codes
and process IDs are in hexadecimal numbers.´

Data Display:

+++++++++++++++++++++++++++
+ CDSP fatal error codes +
+ +
+ Last 4 fatal process +
+ +
+ aaaaaaaa bbb +
+ cccccccc ddd +
+ eeeeeeee fff +
+ gggggggg hhh +
+ +
+++++++++++++++++++++++++++

Abbr Serve Sub Block ID Forma Mod Description

. r t e
a(8) MON FTD_SB_PPC_ADSP_ORI_R DW:H R Last fatal error code.
ESETS_ERROR_CODES _1
b(3) MON FTD_SB_PPC_ADSP_ORI_R W:H R Last process running when the error
ESETS_ERROR_TASK_ID_1 occurred.
c(8) MON FTD_SB_PPC_ADSP_ORI_R DW:H R Last – 1 fatal error code.
ESETS_ERROR_CODES _2
d(3) MON FTD_SB_PPC_ADSP_ORI_R W:H R Last process running when the error
ESETS_ERROR_TASK_ID_2 occurred.
e(8) MON FTD_SB_PPC_ADSP_ORI_R DW:H R Last – 2 fatal error code.
ESETS_ERROR_CODES _3
f(3) MON FTD_SB_PPC_ADSP_ORI_R W:H R Last process running when the error
ESETS_ERROR_TASK_ID_3 occurred.
g(8) MON FTD_SB_PPC_ADSP_ORI_R DW:H R Last – 3 fatal error code.
ESETS_ERROR_CODES _4
h(3) MON FTD_SB_PPC_ADSP_ORI_R W:H R Last process running when the error
ESETS_ERROR_TASK_ID_4 occurred.
 SPECIFICATION 125 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 12.06: CDSP non-fatal error codes (Version: 1, Status: Approved)

This display holds four last non-fatal error codes. The display works in a FIFO principle.
When a new error occurs all the errors are moved forward and if there are errors more than
four, the oldest error code is removed. There are separate queues for fatal and non-fatal
error codes. Also the ID of the last executed process is displayed after the error code.
Codes and process IDs are in hexadecimal numbers.

Data Display:

+++++++++++++++++++++++++++
+ CDSP non-fatal errors +
+ +
+ Last 4 non-fat process +
+ +
+ aaaaaaaa bbb +
+ cccccccc ddd +
+ eeeeeeee fff +
+ gggggggg hhh +
+ +
+++++++++++++++++++++++++++

Abbr Serv Sub Block ID Forma Mod Description

. er t e
a(8) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR DW :H R Last non-fatal error code.
ORS_CODE_1
b(3) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR W :H R Last process running when
OR_TASK_ID _1 the error occurred.
c(8) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR DW :H R Last – 1 non-fatal error code.
ORS_CODE_2
d(3) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR W:H R Last process running when
OR_TASK_ID _2 the error occurred.
e(8) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR DW :H R Last – 2 non-fatal error code.
ORS_CODE_3
f(3) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR W:H R Last process running when
OR_TASK_ID _3 the error occurred.
g(8) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR DW:H R Last – 3 non-fatal error code.
ORS_CODE_4
h(3) MON FTD_SB_PPC_ADSP_NON_FATAL_ERR W:H R Last process running when
OR_TASK_ID _4 the error occurred.
 SPECIFICATION 126 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 12.07: CDSP fatal error code timestamps (Version: 3.31, Status: Approved)

This display holds timestamps for fatal error codes in display 12.05.

Data Display:

+++++++++++++++++++++++++++
+ CDSP fatal timestamps +
+ +
+ date time +
+ +
+ aaaaaa bbbb +
+ cccccc dddd +
+ eeeeee ffff +
+ gggggg hhhh +
+ +
+++++++++++++++++++++++++++

Abbr Serv Sub Block ID For Mod Description

. er mat e
a(6) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Date of the last fatal error. Format:
_CODE_DATE_1 ddmmyy
b(4) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Clock time of the last fatal error.
_CODE_TIME_1 Format:hhmm
c(6) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Date of the last – 1 fatal error. Format:
_CODE_DATE_2 ddmmyy
d(4) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Clock time of the last – 1 fatal error.
_CODE_TIME_2 Format: hhmm
e(6) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Date of the last – 2 fatal error. Format:
_CODE_DATE_3 ddmmyy
f(4) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Clock time of the last – 2 fatal error.
_CODE_TIME_3 Format: hhmm
g(6) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Date of the last – 3 fatal error. Format:
_CODE_DATE_4 ddmmyy
h(4) MON FTD_SB_ADSP_LAST_FATAL_ERR S R Clock time of the last - 3 fatal error.
_CODE_TIME_4 Format: hhmm
 SPECIFICATION 127 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 12.08: CDSP non-fatal error code timestamps (Version: 3.31, Status: Approved)

This display holds timestamps for non-fatal error codes in display 12.06.

Data Display:

+++++++++++++++++++++++++++
+ CDSP non-fatal timest. +
+ +
+ date time +
+ +
+ aaaaaa bbbb +
+ cccccc dddd +
+ eeeeee ffff +
+ gggggg hhhh +
+ +
+++++++++++++++++++++++++++

Abbr. Serve Sub Block ID Forma Mode Description

r t
a(6) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Date of the last non-fatal
RR_CODE_DATE_1 error. Format: ddmmyy
b(4) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Clock time of the last non-
RR_CODE_TIME_1 fatal error. Format: hhmm
c(6) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Date of the last – 1 non-
RR_CODE_DATE_2 fatal error. Format:
ddmmyy
d(4) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Clock time of the last – 1
RR_CODE_TIME_2 non-fatal error. Format:
hhmm
e(6) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Date of the last – 2 non-
RR_CODE_DATE_3 fatal error. Format:
ddmmyy
f(4) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Clock time of the last – 2
RR_CODE_TIME_3 non-fatal error. Format:
hhmm
g(6) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Date of the last – 3 non-
RR_CODE_DATE_4 fatal error. Format:
ddmmyy
h(4) MON FTD_SB_ADSP_LAST_NON_FATAL_E S R Clock time of the last - 3
RR_CODE_TIME_4 non-fatal error. Format:
hhmm
 SPECIFICATION 128 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 12.09: Counters for failed application starts (Version: 1, Status: Approved)

This display holds counters for failed application starts.

Data Display:

+++++++++++++++++++++++++++
+ Failed applicat. starts +
+ +
+ Audio aaaa +
+ Voice bbbb +
+ Midi cccc +
+ Video dddd +
+ +
+ Res Res eeee ffff +
+ Res Res gggg hhhh +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Format Mode Description

.
Aaaa ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Counter for
_CNT_1 failed audio
application start
requests.
bbbb ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Counter for
_CNT_2 failed voice
application start
requests.
Cccc ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Counter for
_CNT_3 failed midi
application start
requests.
Dddd ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Counter for
_CNT_4 failed video
application start
requests.
Eeee ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Reserved.
_CNT_5
Ffff ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Reserved.
 SPECIFICATION 129 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

_CNT_6
Gggg ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Reserved.
_CNT_7
Hhhh ADSP_CORE FTD_SB_ADSP_APP_START_FAIL W:D R Reserved.
_CNT_8

Display 12.10: Common CDSP test data display (Version: 3.22, Status: Approved)

This display prompts for a number, which is then sent to the CDSP. The CDSP responds
with four 12 character string, which are displayed by the FTD.

Data Display:

+++++++++++++++++++++++++++
+ Common CDSP test data +
+ +
+ +
+ aaaaaaaaaaaa +
+ bbbbbbbbbbbb +
+ cccccccccccc +
+ dddddddddddd +
+ +
+ +
+++++++++++++++++++++++++++

To select the test data to be show, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 1210 (CDSP SW platform; Common CDSP test data
display) to the query prompt.
5. “INPUT” prompt will be shown on the display, ented data number.
6. Confirm with the Ok button.
Abbr. Server Sub Block ID Forma Mod Description
t e
INPUT ADSP_COR FTD_SB_ADSP_TEST_IN DW:D R Select data to be shown by giving
E DEX the index of the data.
a(12) ADSP_COR FTD_SB_ADSP_TEST_DA S R CDSP test data.
E TA_1
b(12) ADSP_COR FTD_SB_ADSP_TEST_DA S R CDSP test data.
E TA_2
c(12) ADSP_COR FTD_SB_ADSP_TEST_DA S R CDSP test data.
E TA_3
d(12) ADSP_COR FTD_SB_ADSP_TEST_DA S R CDSP test data.
E TA_4
 SPECIFICATION 130 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved
 SPECIFICATION 131 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 41: WCDMA CDSP displays

The displays in this group show CDSP specific information.

Display 41.01: RACH MSG TX profile (Version: 3.19, Status: Approved)

RACH MSG TX profile shows detailed information about latest RACH message
transmission procedure.

Data Display:

+++++++++++++++++++++++++++
+ RACH MSG TX profile +
+ Initial TxtxPower aaa +
+ Po bbb Pp_m ccc SFN ddd +
+ A_slot ee SubChan fff +
+ Lenght g Sign_m hhhh +
+ Sign_rnd iiii Pre lll +
+ D_CH_G k C_CH_G j +
+ Message m data n +
+ Message tx power ooo +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Format Mode Description

.
a(3) WCDMA_D FTD_WDSP_SB_INI W:D R,I,O Initial transmission power, unit dBm.
SP_CS T_TX_PWR Value range –99 … +99.
b(3) WCDMA_D FTD_WDSP_SB_TX W:D R,I,O Po parameter, unit dBm. Value range –99
SP_CS _PO_PARAM … +99.
c(3) WCDMA_D FTD_WDSP_SB_TX W:D R,I,O Pp_m parameter, unit dBm. Value range –
SP_CS _PP_M_PARAM 99 … +99.
d(3) WCDMA_D FTD_WDSP_SB_TX W:H R,I,O Base sfn for transmission start timing in
SP_CS _START_TIMING hexadecimal format, value range 0x0 -
0xFFF
e(2) WCDMA_D FTD_WDSP_SB_TX B:D R,I,O First used access slot in decimal format,
SP_CS _FIRST_ACCESS_S value range 0 … 59
LOT
f(3) WCDMA_D FTD_WDSP_SB_TX W:H R,I,O Subchannel mask in hexadecimal format,
SP_CS _SUBCH_MASK value range 0x0 … 0xFFF
g WCDMA_D FTD_WDSP_SB_TX B:D R,I,O Message length, two values:
SP_CS _MSG_LEN 1: 10 ms
2: 20 ms
h(4) WCDMA_D FTD_WDSP_SB_TX W:H R,I,O Available signatures selection mask in
SP_CS _SIGSEL_MASK hexadecimal format, value range 0x0 …
0xFFFF
I(4) WCDMA_D FTD_WDSP_SB_TX W:H R,I,O Signature selection random seed in
SP_CS _SIGSEL_RND hexadecimal format, value range 0x0
…0xFFFF
j WCDMA_D FTD_WDSP_SB_TX B:H R,I,O Control channel gain in hexadecimal
SP_CS _CTRL_CH_GAIN format, value range 0x0 … 0xF
k WCDMA_D FTD_WDSP_SB_TX B:H R,I,O Data channel gain in hexadecimal format,
SP_CS _DATA_CH_GAIN value range 0x0 … 0xF
l(3) WCDMA_D FTD_WDSP_SB_TX W:H R,I,O Preamble transmission count in
SP_CS _PREAMP_COUNT hexadecimal format, value range 0x0
 SPECIFICATION 132 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

…0xFFF
m PN_WCDM FTD_WDSP_SB_TX B:D R,I,O Message transmission result, three
A_DSP_CS _MSG_RES values:
.
0: Message not transmitted
1: Message transmitted
2: Message transmission denied
n PN_WCDM FTD_WDSP_SB_TX B:D R,I,O Data channel spreading factor, four
A_DSP_CS _DATA_CH_SF values:
0: SF256
1: SF128
2: SF64
3: SF32
o(3) PN_WCDM FTD_WDSP_SB_TX W:D R,I,O Message transmission power, unit dBm.
A_DSP_CS _MSG_PWR Value range –99 … +99.

Display 41.02: Dedicated uplink channel power control status (Version: 3.24, Status: Approved)

This display gives a quick overview of the current uplink dedicated channel power control
status. From this display the operating point of the uplink power control can be seen

Data Display:

+++++++++++++++++++++++++++
+ Dedicated tx power info +
+ Tx min/max aaa bbb +
+ Tx current ccc +
+ Algo e step f SSDT g +
+ Tx loop h DPCCH i +
+ Comp mode j sync k +
+ PhCh min l PhCh max m +
+ PhCh average nnnnn +
+ Ul+ ooooo Ul- ppppp +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Format Mode Description

.
a(3) WCDM FTD_SB_WDSP_TX_MIN_ W:D R,I,O Minimum TX power during the
A_DSP_ PWR display update period, unit dBm.
CS Value range –99 … +99.
b(3) WCDM FTD_SB_WDSP_TX_MAX W:D R,I,O Maximum TX power during the
A_DSP_ _PWR display update period, unit dBm.
CS Value range –99 … +99.
c(3) WCDM FTD_SB_WDSP_TX_CUR W:D R,I,O Current TX power at display update
A_DSP_ _PWR time, unit dBm. Value range –99 …
CS +99.
e WCDM FTD_SB_WDSP_TX_PWR B:D R,I,O Current power control algorithm type,
A_DSP_ _CTRL_ALG 1 = power control algorithm 1
CS 2 = power control algorithm 2
f WCDM FTD_SB_WDSP_TX_PWR B:D R,I,O Current power control step size, unit
A_DSP_ _STEP dB, value range 1 .. 2.
CS
 SPECIFICATION 133 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Format Mode Description

.
g WCDM FTD_SB_WDSP_TX_SSD B:D R,I,O Current SSDT state values:
A_DSP_ T 0: not active
CS 1: active
h WCDM FTD_SB_WDSP_TX_DIV_ B:D R,I,O TX closed loop diversity state,
A_DSP_ MODE values:
CS 0: not active
1: Closed loop mode 1
2: Closed loop mode 2
I WCDM FTD_SB_WDSP_TX_DPC B:D R,I,O DPCCH frame format, value range 0
A_DSP_ CH_FFORM …5.
CS
j WCDM FTD_SB_WDSP_TX_CM_ B:D R,I,O Compressed mode used during
A_DSP_ MODE display update period, values:
CS 0: No compressed mode
1: Compressed mode active
k WCDM FTD_SB_WDSP_TX_OOS B:D R,I,O Out of sync state visited during
A_DSP_ display update period, values:
CS 0: No out of sync
1: Out of sync active
l WCDM FTD_SB_WDSP_TX_MIN_ B:H R,I,O Minimum PhCh bit rate used in the
A_DSP_ PHCH_BIT_RATE uplink frames during display update
CS period. Value range is 0 …12, shown
as hexadecimal number. Value
coding is as follows:
Range 0: 0
Range 1-6: 2^(L - 1) * 150
Range 8-12: (L - 6) * 9600

m WCDM FTD_SB_WDSP_TX_MAX B:H R,I,O Maximum PhCh bit rate used in the
A_DSP_ _PHCH_BIT_RATE uplink frames during display update
CS period. Value range is 0 …12, shown
as hexadecimal number. Value
coding is as follows:
Range 0: 0
Range 1-6: 2^(m - 1) * 150
Range 8-12: (m - 6) * 9600

n(5) WCDM FTD_SB_WDSP_TX_AVR W:D R,I,O Average PhCH frame bit rate during
A_DSP_ _PHCH_BIT_RATE display update period, value range 0
CS …57600
o(5) WCDM FTD_SB_WDSP_TX_NUM DW:D R,I,O Amount of derived "increase power"
A_DSP_ _OF_UL_INC_PWR_COM uplink power control commands
CS MANDS during display update period.
Value range 0 .. 99999.
p(5) WCDM FTD_SB_WDSP_TX_NUM DW:D R,I,O Amount of derived "decrease power"
A_DSP_ _OF_UL_DEC_PWR_COM uplink power control commands
CS MANDS during display update period.
Value range 0 … 99999.

Display 41.03: Dedicated downlink channel power control status (Version: 3.19, Status:
Approved)

This display gives a quick overview of the current downlik dedicated channel power control
status. From this display the operating point of the downlink power control can be seen
 SPECIFICATION 134 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Data Display:

+++++++++++++++++++++++++++
+ Dedicated tx power info +
+ +
+ SIR minimum aaaa +
+ SIR maximum bbbb +
+ SIR current cccc +
+ Downlink increase ddddd +
+ Downlink decrease eeeee +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(4) WCDM FTD_SB_WDSP_TARGET W:D R,I,O Minimum target SIR value during
A_DSP_ _SIR_MIN display update period. Unit is dBm /
CS 10.
Value range is –320 … 310.
b(4) WCDM FTD_SB_WDSP_TARGET W:D R,I,O Maximum target SIR value during
A_DSP_ _SIR_MAX display update period. Unit is dBm /
CS 10
Value range is –320 … 310.
c(4) WCDM FTD_SB_WDSP_TARGET W:D R,I,O Current target SIR at display update
A_DSP_ _SIR_CURRENT time. Unit is dBm / 10.
CS Value range is –320 … 310.
d(5) WCDM FTD_SB_WDSP_NUM_OF DW:D R,I,O Amount of sent "increase power"
A_DSP_ _DL_INC_PWR_COMMAN downlink power control commands
CS DS during display update period.
Value range is 0 … 99999
e(5) WCDM FTD_SB_WDSP_NUM_OF DW:D R,I,O Amount of sent "decrease power"
A_DSP_ _DL_DEC_PWR_COMMA downlink power control commands
CS NDS during display update period.
Value range is 0 … 99999

Display 41.04: WCDMA AFC status (Version: 3.13, Status: Approved)

The purpose of the display is to monitor WCDMA AFC behavior (including aging algorithm).

Data Display:

+++++++++++++++++++++++++++
+ WCDMA AFC status +
+ +
+ AFC DAC init aaaa +
+ AFC DAC current bbbb +
+ AFC DAC minimum cccc +
+ AFC DAC maximum dddd +
+ +
+ +
+ +
 SPECIFICATION 135 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(4) WCDM FTD_SB_WDSP_AFC_INI W:D R Initial AFC DAC setting. Value range
A_DSP_ T_DAC 0 to 2047.
CS
b(4) WCDM FTD_SB_WDSP_AFC_CU W:D R Current AFC DAC setting. Value
A_DSP_ RR_DAC range 0 to 2047.
CS
c(4) WCDM FTD_SB_WDSP_AFC_MIN W:D R Minimum AFC DAC setting during
A_DSP_ _CURR_DAC display update period. Value range 0
CS to 2047.
d(4) WCDM FTD_SB_WDSP_AFC_MA W:D R Maximum AFC DAC setting during
A_DSP_ X_CURR_DAC display update period. Value range 0
CS to 2047.

Display 41.05: CDSP load status (Version: 3.19, Status: Approved)

This display gives information about the CDSP processor load.

Data Display:

+++++++++++++++++++++++++++
+ CDSP load status +
+ Act mode aaaaa% +
+ very light sleep bbbbb% +
+ light sleep ccccc% +
+ deep sleep ddddd% +
+ Act mode eeeeee +
+ very light sleep ffffff +
+ light sleep gggggg +
+ deep sleep hhhhhh +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(5) FTD_SB_WDSP_LOAD_A W:D R Amount of time spent in active mode
WCDM CT_PORTION during display update period. Value
A_DSP_ is relative portion, range 0 ... 10000.
CS
b(5) WCDM FTD_SB_WDSP_LOAD_V W:D R Amount of time spent in very light
A_DSP_ LS_PORTION sleep mode during display update
CS period. Value is relative portion,
range 0 ... 10000.
c(5) WCDM FTD_SB_WDSP_LOAD_L W:D R Amount of time spent in light sleep
A_DSP_ S_PORTION mode during display update period.
CS Value is relative portion, range 0 ...
10000.
d(5) WCDM FTD_SB_WDSP_LOAD_D W:D R Amount of time spent in deep sleep
A_DSP_ S_PORTION mode during display update period.
CS Value is relative portion, range 0 ...
10000.
 SPECIFICATION 136 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
e(6) WCDM FTD_SB_WDSP_LOAD_A DW:H R Amount of time spent in active mode
A_DSP_ CT_CYCLES during display update period. Value
CS is sleep clock cycles (one cycle
duration is approximately 30.5 µs).
f(6) WCDM FTD_SB_WDSP_LOAD_V DW:H R Amount of time spent in very light
A_DSP_ LS_CYCLES sleep mode during display update
CS period. Value is sleep clock cycles
(one cycle duration is approximately
30.5 µs).
g(6) WCDM FTD_SB_WDSP_LOAD_L DW:H R Amount of time spent in light sleep
A_DSP_ S_CYCLES mode during display update period.
CS Value is sleep clock cycles (one
cycle duration is approximately 30.5
µs).
h(6) WCDM FTD_SB_WDSP_LOAD_D DW:H R Amount of time spent in deep sleep
A_DSP_ S_CYCLES mode during display update period.
CS Value is sleep clock cycles (one
cycle duration is approximately 30.5
µs).

Display 41.06: Downlink receiver gain control status (Version: 3.28, Status: Approved)

This display gives information about WCDMA downlink receiver gain control operating
point.

Data Display:

+++++++++++++++++++++++++++
+ Downlink rx gain status +
+ +
+ Rx ana/digi aa fff +
+ BB amp bb Gain pre c +
+ LNA state d LNA bias e +
+ RSSI before FIR gggg +
+ RSSI after FIR hhhh +
+ Amp estim analog iiii +
+ Amp estim digital jjjj +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(2) WCDM FTD_SB_WDSP_RX_GAIN B:D R Analog AGC's RX_dB counter. Value
A_DSP_ _ANA_AGC_DB_COUNT range 0…27.
CS
b(2) WCDM FTD_SB_WDSP_RX_GAIN B:D R Control word of BB amplifier. Value
A_DSP_ _BB_AMP range 0…18.
CS
c WCDM FTD_SB_WDSP_RX_GAIN B:D R Gain of preamplifier.
A_DSP_ _PRE_AMP 0 = minimum gain
CS 1 = maximum gain
 SPECIFICATION 137 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
d WCDM FTD_SB_WDSP_RX_GAIN B:D R LNA state.
A_DSP_ _LNA 3 = LNA has maximum gain
CS 1 = LNA has middle gain
0 = LNA has minimum gain
e WCDM FTD_SB_WDSP_RX_GAIN B:H R LNA bias state.
A_DSP_ _LNA_BIAS 1 = half bias current
CS 0 = normal bias current
f(3) WCDM FTD_SB_WDSP_RX_GAIN W:D R Digital AGC's RX_dB counter. Value
A_DSP_ _DIGI_AGC_DB_COUNT range 0 … 511.
CS
g(4) WCDM FTD_SB_WDSP_RX_GAIN W:D R RSSI before FIR,
A_DSP_ _RSSI_ANA_DBM range –240 … +20 (-120 dBm … +10
CS dBm) ,
unit dBm,
format q1_16
h(4) WCDM FTD_SB_WDSP_RX_GAIN W:D R RSSI after FIR,
A_DSP_ _RSSI_DIGI_DBM range –240 … +20
CS (-120 dBm … +10 dBm)
unit dBm,
format q1_16
I(4) WCDM FTD_SB_WDSP_RX_GAIN W:H R Amplitude estimate of analog AGC.
A_DSP_ _ANA_AMP_EST Value range 0x0000…0xFFFF
CS
j(4) WCDM FTD_SB_WDSP_RX_GAIN W:H R Amplitude estimate of digital AGC.
A_DSP_ _DIGI_AMP_EST Value range 0x0000…0xFFFF
CS

Display 41.07: WCDMA rake receiver status (Version: 3.13, Status: Approved)

This display gives information about WCDMA downlink rake receiver operating point

Data Display:

+++++++++++++++++++++++++++
+ WCDMA rake receiver +
+ +
+ Active BS a +
+ Active PHCH b +
+ Fingers c +
+ Delay dddd +
+ Master fingers ee +
+ Finger alloc ffffffffff +
+ Finger algor gggggggggg +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a WCDM FTD_SB_WDSP_RAKE_N B:D R Number of active BSs in rake. Value
A_DSP_ UM_OF_ACTIVE_BS range 0 … 6.
CS
 SPECIFICATION 138 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
b WCDM FTD_SB_WDSP_RAKE_N B:D R Number of active PHCHs in rake.
A_DSP_ UM_OF_ACTIVE_PHCH Value range 0 … 3.
CS
c WCDM FTD_SB_WDSP_RAKE_N B:D R Number of allocated fingers i.e
A_DSP_ UM_OF_USED_FINGERS multipaths (filtered average over 50
CS frames). Value range 0 … 8.
d(4) WCDM FTD_SB_WDSP_RAKE_D W:D R Time difference of 1st and last
A_DSP_ ELAY_SPREAD multipath used for combining, value
CS range 0 … 5120, unit 0.1 chips.

e(2) WCDM FTD_SB_WDSP_RAKE_A B:H R Currently allocated master fingers.

A_DSP_ LLOCATED_MASTERS Bit #0 (mask 0x01) = Master finger 0
CS Bit #1 (mask 0x02) = Master finger 1
…
Bit #7 (mask 0x80)= Master finger 7
f(10) WCDM FTD_SB_WDSP_RAKE_A DW:D R Number of finger allocations done
A_DSP_ LLOC_COUNT during display update period on
CS current PhCHs.
g(10) WCDM FTD_SB_WDSP_RAKE_A DW:D R Number of finger allocation algorithm
A_DSP_ LLOC_CALL_COUNT calls done during display update
CS period on current PhCHs.

Display 41.08: WCDMA decoder status (Version: 3.13, Status: Approved)

This display gives a quick overview of the current decoder internal values regarding
reception quality and sync status

Data Display:

+++++++++++++++++++++++++++
+ WCDMA decoder status +
+ +
+ TFCI forced aaaa +
+ TFCI BER bbbb +
+ BER cccc BLER dddd +
+ Sync lost eeee +
+ Sync status f +
+ Spreading factor ggg +
+ Slot format hh +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(4) WCDM FTD_SB_WDSP_DEC_FO W:H R Number of forced TFCI values in
A_DSP_ RCED_TFCI display update period.
CS
b(4) WCDM FTD_SB_WDSP_DEC_TF W:H R TFCI BER averaged over display
A_DSP_ CI_BER update period.
CS
 SPECIFICATION 139 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
c(4) WCDM FTD_SB_WDSP_DEC_BE W:H R BER used by the sync status
A_DSP_ R algorithm (based on the TPC or the
CS PILOT bits, depending on the
situation). Averaged over display
update period.
d(4) WCDM FTD_SB_WDSP_DEC_BL W:H R BLER in q12_16 format. This is the
A_DSP_ ER combined BLER for all the trch with
CS BLER being measured, used by
outer loop power control (averaged
over display update period)
e(4) WCDM FTD_SB_WDSP_DEC_SY W:H R Number of times the phone lost sync
A_DSP_ NC_LOST since the activation of the display.
CS
f WCDM FTD_SB_WDSP_DEC_SY B:D R SYNC sync status: 0 out of sync
A_DSP_ NC_STATUS 1 in sync
CS
g(3) WCDM FTD_SB_WDSP_DEC_SP B:D R Spreading factor
A_DSP_ READING_FACTOR
CS
h(2) WCDM FTD_SB_WDSP_DEC_SL B:D R Slot format used in the physical
A_DSP_ OT_FORMAT channel
CS

Display 41.09: Common WCDMA DSP CS scratchpad display (interactive) (Version: 3.19, Status:
Approved)

This display provides a generic display template that can be used to display any data on
field test display. This display is needed in order to be able to support for the various needs
detected in field testing. With this display quick test-specific temporary displays can be
easily added to support specific problems detected in field testing.The display prompts for
an index and then shows the data associated with the given index. Use the following steps
to activate this display. The display is not activated if the arrow (∧∨) buttons are used.

1. Press the Menu button.

2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display by giving the display number 4109 to the query prompt.
5. Test input prompt will be shown on the display. Enter scratchpad index.
6. Confirm with the Ok button.
7. Data associated with the given index is shown if the activation was successful.

Data Display:

+++++++++++++++++++++++++++
+ Interactive CDSP +
+ scratchpad display +
+ +
+ aaaaaaaaaaaa +
+ bbbbbbbbbbbb +
+ cccccccccccc +
+ dddddddddddd +
 SPECIFICATION 140 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
INPU WCDM FTD_SB_WDSP_SCRATC DW:D R Scratchpad index, see project
T A_DSP_ HPAD_INDEX specific documentation.
CS
a(12) WCDM FTD_SB_WDSP_SCRATC S R FTD data 0 … 12 character string
A_DSP_ HPAD_DATA1
CS
b(12) WCDM FTD_SB_WDSP_SCRATC S R FTD data 0 … 12 character string
A_DSP_ HPAD_DATA2
CS
c(12) WCDM FTD_SB_WDSP_SCRATC S R FTD data 0 … 12 character string
A_DSP_ HPAD_DATA3
CS
d(12) WCDM FTD_SB_WDSP_SCRATC S R FTD data 0 … 12 character string
A_DSP_ HPAD_DATA4
CS

Display 41.10: FDD neighbour cell summary (Version: 3.13, Status: Approved)

This displays summarises the number of cells in the active, monitored, detected and
undetected sets on the 3 frequencies. Active and detected sets only contain cells on the
home frequency

Data Display:

+++++++++++++++++++++++++++
+ FDD neighbour cell info +
+ Active cells aa +
+ Intra cells bb +
+ Inter 1 freq cc +
+ Inter 2 freq dd +
+ Detected cells ee +
+ Intra cells undetect ff +
+ Inter 1 freq undet gg +
+ Inter 2 freq undet hh +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in the active set
A_DSP_ UM_INTRA_ACTIVE
CS
b(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in intra-freq
A_DSP_ UM_INTRA_MON monitired set
CS
 SPECIFICATION 141 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
c(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in Inter 1 freq
A_DSP_ UM_INTER1_MON monitored set
CS
d(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in Inter 2 freq
A_DSP_ UM_INTER2_MON monitored set
CS
e(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in detected set
A_DSP_ UM_INTRA_DET
CS
f(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in Intra freq
A_DSP_ UM_INTRA_UNDET neighbour list that are undetected
CS
g(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in Inter1 freq
A_DSP_ UM_INTER1_UNDET neighbour list that are undetected
CS
h(2) WCDM FTD_SB_WDSP_CELL_S W:D R,I,O Number of cells in Inter2 freq
A_DSP_ UM_INTER2_UNDET neighbour list that are undetected
CS

Display 41.11: FDD ranking summary (Version: 3.24, Status: Approved)

This display shows the 4 highest ranked cells. The ranking criteria (RSCP, EcNo) will be
automatically selected based on the parameters received from the network

Data Display:

+++++++++++++++++++++++++++
+ FDD ranking summary +
+ Freq1 BS1 System +
+ aaaaa eee i +
+ Freq2 BS2 System +
+ bbbbb fff j +
+ Freq3 BS3 System +
+ ccccc ggg k +
+ Freq4 BS4 System +
+ ddddd hhh l +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(5) WCDM FTD_SB_WDSP_RANK_F W:D R,I,O Cell 1 frequency code, center
A_DSP_ REQ_1 frequency is value / 5.
CS
b(5) WCDM FTD_SB_WDSP_RANK_F W:D R,I,O Cell 2 frequency code, center
A_DSP_ REQ_2 frequency is value / 5.
CS
c(5) WCDM FTD_SB_WDSP_RANK_F W:D R,I,O Cell 3 frequency code, center
A_DSP_ REQ_3 frequency is value / 5.
CS
d(5) WCDM FTD_SB_WDSP_RANK_F W:D R,I,O Cell 4 frequency code, center
A_DSP_ REQ_4 frequency is value / 5.
CS
 SPECIFICATION 142 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
e(3) WCDM FTD_SB_WDSP_RANK_B W:D R,I,O Cell 1 BS ID
A_DSP_ SID_1
CS
f(3) WCDM FTD_SB_WDSP_RANK_B W:D R,I,O Cell 2 BS ID
A_DSP_ SID_2
CS
g(3) WCDM FTD_SB_WDSP_RANK_B W:D R,I,O Cell 3 BS ID
A_DSP_ SID_3
CS
h(3) WCDM FTD_SB_WDSP_RANK_B W:D R,I,O Cell 4 BS ID
A_DSP_ SID_4
CS
i WCDM FTD_SB_WDSP_RANK_S S R,I,O FDD home cell = "W",
A_DSP_ YSTEM_1 FDD neighbour cell = "w"
CS GSM neigbour cell = "g"
Data not available = "-"
In case data is not available also
corresponding frequency and BS ID
field values are meaningless.

j WCDM FTD_SB_WDSP_RANK_S S R,I,O FDD home cell = "W",

A_DSP_ YSTEM_2 FDD neighbour cell = "w"
CS GSM neigbour cell = "g"
Data not available = "-"
In case data is not available also
corresponding frequency and BS ID
field values are meaningless.

k WCDM FTD_SB_WDSP_RANK_S S R,I,O FDD home cell = "W",

A_DSP_ YSTEM_3 FDD neighbour cell = "w"
CS GSM neigbour cell = "g"
Data not available = "-"
In case data is not available also
corresponding frequency and BS ID
field values are meaningless.

l WCDM FTD_SB_WDSP_RANK_S S R,I,O FDD home cell = "W",

A_DSP_ YSTEM_4 FDD neighbour cell = "w"
CS GSM neigbour cell = "g"
Data not available = "-"
In case data is not available also
corresponding frequency and BS ID
field values are meaningless.

Display 41.12: FDD Frequency summary (Version: 3.13, Status: Approved)

This display shows the RSSI measured on the 3 FDD frequencies being used by the UE

Data Display:

+++++++++++++++++++++++++++
+ FDD frequency summary +
+ +
 SPECIFICATION 143 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Freq INTRA RSSI +

+ aaaaa dddd +
+ Freq INTRA RSSI +
+ bbbbb eeee +
+ Freq INTRA RSSI +
+ ccccc ffff +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(5) WCDM FTD_SB_WDSP_FREQ_IN W:D R,I,O Frequency code of home cell, center
A_DSP TRA frequency is value / 5.
_CS
b(5) WCDM FTD_SB_WDSP_FREQ W:D R,I,O Frequency code of measured
A_DSP _INTER1 frequency 1, center frequency is
_CS value / 5.
c(5) WCDM FTD_SB_WDSP_FREQ W:D R,I,O Frequency code of measured
A_DSP _INTER2 frequency 2, center frequency is
_CS value / 5.
d(4) WCDM FTD_SB_WDSP_RSSI_INT W:D R,I,O INTRA RSSI * -10
A_DSP RA
_CS
e(4) WCDM FTD_SB_WDSP_RSSI W:D R,I,O INTER1 RSSI * -10
A_DSP _INTER1
_CS
f(4) WCDM FTD_SB_WDSP_RSSI W:D R,I,O INTER2 RSSI * - 10
A_DSP _INTER2
_CS

Display 41.13: FDD intra frequency neighbour summary (Version: 3.13, Status: Approved)

This displays shows the status of eight best ranked neighbour cells on home cell frequency

Data Display:

+++++++++++++++++++++++++++
+ FDD intra freq neigh +
+ Stat ID Ec Stat ID Ec +
+ a bbb cc d eee ff +
+ Stat ID Ec Stat ID Ec +
+ g hhh ii j kkk ll +
+ Stat ID Ec Stat ID Ec +
+ m nnn oo p qqq rr +
+ Stat ID Ec Stat ID Ec +
+ s ttt uu v xx yy +
+++++++++++++++++++++++++++
 SPECIFICATION 144 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
a WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_1 “a” = Active set, STTD not active on
SP_C PCCPCH.
S “m” = Monitored set, STTD not active
on PCCPCH.
“d” = Detected set, STTD not active
on PCCPCH.
“u” = Undetected, STTD not active on
PCCPCH.
“n” = Not listed or detected, STTD
not active on PCCPCH.
“A” = Active set, STTD active on
PCCPCH.
“M” = Monitored set, STTD active on
PCCPCH.
“D” = Detected set, STTD active on
PCCPCH.
“U” = Undetected, STTD active on
PCCPCH.
“N” = Not listed or detected, STTD
active on PCCPCH.
b(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_1
SP_C
S
c(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_1
SP_C
S
d WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_2
SP_C
S
e(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_2
SP_C
S
f(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_2
SP_C
S
g WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_3
SP_C
S
h(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_3
SP_C
S
I(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_3
SP_C
S
 SPECIFICATION 145 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
j WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_4
SP_C
S
k(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_4
SP_C
S
l(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_4
SP_C
S
m WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_5
SP_C
S
n(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_5
SP_C
S
o(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_5
SP_C
S
p WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_6
SP_C
S
q(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_6
SP_C
S
r(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_6
SP_C
S
s WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_7
SP_C
S
t(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_7
SP_C
S
u(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_7
SP_C
S
v WCD FTD_SB_WDSP_DETECT_I S R,I,O BS status
MA_D NTRA_STATUS_8
SP_C
S
x(3) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O BS ID on INTRA
MA_D NTRA_BSID_8
SP_C
S
 SPECIFICATION 146 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
y(2) WCD FTD_SB_WDSP_DETECT_I W:D R,I,O Cell Ec/No * -1
MA_D NTRA_ECNO_8
SP_C
S

Displays 41.14 – 41.15: FDD inter frequencies 1 and 2 neighbour summary (Version: 3.13, Status:
Approved)

These two displays show the status of eight best ranked neighbour cells on inter
frequencies 1 and 2. Display 41.14 shows inter frequency 1 summary and 41.15 inter
frequency 2 summary.

Data Display:

+++++++++++++++++++++++++++
+ FDD inter freq neigh +
+ Stat ID Ec Stat ID Ec +
+ a bbb cc d eee ff +
+ Stat ID Ec Stat ID Ec +
+ g hhh ii j kkk ll +
+ Stat ID Ec Stat ID Ec +
+ m nnn oo p qqq rr +
+ Stat ID Ec Stat ID Ec +
+ s ttt uu v xxx yy +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_1 “a” = Active set, STTD not active on
CS PCCPCH.
“m” = Monitored set, STTD not active
on PCCPCH.
“d” = Detected set, STTD not active
on PCCPCH.
“u” = Undetected, STTD not active on
PCCPCH.
“n” = Not listed or detected, STTD
not active on PCCPCH.
“A” = Active set, STTD active on
PCCPCH.
“M” = Monitored set, STTD active on
PCCPCH.
“D” = Detected set, STTD active on
PCCPCH.
“U” = Undetected, STTD active on
PCCPCH.
“N” = Not listed or detected, STTD
active on PCCPCH.
b(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_1
CS
 SPECIFICATION 147 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
c(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_1
CS
d WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_2
CS
e(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_2
CS
f(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_2
CS
g WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_3
CS
h(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_3
CS
I(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_3
CS
j WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_4
CS
k(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_4
CS
l(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_4
CS
m WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_5
CS
n(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_5
CS
o(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_5
CS
p WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_6
CS
q(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_6
CS
r(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_6
CS
s WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_7
CS
t(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_7
CS
 SPECIFICATION 148 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
u(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_7
CS
v WCDM FTD_SB_WDSP_DETECT S R,I,O BS status
A_DSP_ _INTERx_STATUS_8
CS
x(3) WCDM FTD_SB_WDSP_DETECT W:D R,I,O BS ID on INTERx
A_DSP_ _INTERx_BSID_8
CS
y(2) WCDM FTD_SB_WDSP_DETECT W:D R,I,O Cell Ec/No * -1
A_DSP_ _INTERx_ECNO_8
CS

where “x” denotes the number of the inter frequence., x=1 in display 41.14 and x=2 in
display 41.15.

Display 41.16: FDD mode GSM cell detection summary (Version: 3.13, Status: Approved)

Displays the top 4 GSM cells showing the frequency code, measured RSSI and if the BSIC
has been verified.

Data Display:

+++++++++++++++++++++++++++
+ FDD mode GSM cell detec +
+ GSM1 RSSI Verified +
+ aaaa eeee i +
+ GSM2 RSSI Verified +
+ bbbb ffff j +
+ GSM3 RSSI Verified +
+ cccc gggg k +
+ GSM4 RSSI Verified +
+ dddd hhhh l +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
a(4) WCDM FTD_SB_WDSP_GSM_FR W:D R,I,O GSM Cell 1 frequency code
A_DSP_ EQ_1
CS
b(4) WCDM FTD_SB_WDSP_GSM_FR W:D R,I,O GSM Cell 2 frequency code
A_DSP_ EQ_2
CS
c(4) WCDM FTD_SB_WDSP_GSM_FR W:D R,I,O GSM Cell 3 frequency code
A_DSP_ EQ_3
CS
d(4) WCDM FTD_SB_WDSP_GSM_FR W:D R,I,O GSM Cell 4 frequency code
A_DSP_ EQ_4
CS
e(4) WCDM FTD_SB_WDSP_GSM_RS W:D R,I,O Cell 1 RSSI *-10
A_DSP_ SI_1
CS
 SPECIFICATION 149 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
f(4) WCDM FTD_SB_WDSP_GSM_RS W:D R,I,O Cell 2 RSSI *-10
A_DSP_ SI_2
CS
g(4) WCDM FTD_SB_WDSP_GSM_RS W:D R,I,O Cell 3 RSSI *-10
A_DSP_ SI_3
CS
h(4) WCDM FTD_SB_WDSP_GSM_RS W:D R,I,O Cell 4 RSSI *-10
A_DSP_ SI_4
CS
I WCDM FTD_SB_WDSP_GSM_ST S R,I,O Cell 1 verified status “V”=verified, “N”
A_DSP_ ATUS_1 = Not verified
CS
j WCDM FTD_SB_WDSP_GSM_ST S R,I,O Cell 2 verified status “V”=verified, “N”
A_DSP_ ATUS_2 = Not verified
CS
k WCDM FTD_SB_WDSP_GSM_ST S R,I,O Cell 3 verified status “V”=verified, “N”
A_DSP_ ATUS_3 = Not verified
CS
l WCDM FTD_SB_WDSP_GSM_ST S R,I,O Cell 4 verified status “V”=verified, “N”
A_DSP_ ATUS_4 = Not verified
CS

Display 41.17: FDD detailed cell info (interactive): (Version: 3.16, Status: Approved)

This display promts for a cell frequence code and BSID and shows info about the selected
cell.

Use the following steps to activate this display in interactive mode. The display is not
activated if the arrow (∧∨) buttons are used.

1. Press the Menu button.

2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display by giving the display number 4117 to the query prompt.
5. Test input prompt will be shown on the display. Enter frequency code and BSID as specified in the
table below.
6. Confirm with the Ok button.
7. Info about the cell is shown if the activation was successful.

Data Display:

+++++++++++++++++++++++++++
+ FDD detailed cell info +
+ +
+ Frequency code aaaaa +
+ RSSI bbbb BsID ccc +
+ R_Order dd BsStatus e +
+ Syncro f TxDiv g +
+ Frame timing hhhhh +
+ SCPICH l EcNO jjj +
+ RSCP kkkk +
 SPECIFICATION 150 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mode Description

. t
INPU WCDM FTD_SB_WDSP_CELL_IN DW:D R,O.I Format xxxxxyyy, where
T A_DSP_ PUT xxxxx:: frequency code (decimal)
CS yyy: BSID (decimal)
a(5) WCDM FTD_SB_WDSP_CELL_D W:D R,I,O Frequency code
A_DSP_ ETAIL_FREQ
CS
b(4) WCDM FTD_SB_WDSP_CELL_D W:D R,I,O RSSI * -10
A_DSP_ ETAIL_RSSI
CS
c(3) WCDM FTD_SB_WDSP_CELL_D W:D R,I,O BS ID
A_DSP_ ETAIL_BSID
CS
d(2) WCDM FTD_SB_WDSP_CELL_D W:D R,I,O cell ranking order
A_DSP_ ETAIL_RANK
CS
e WCDM FTD_SB_WDSP_CELL_D S R,I,O BS status
A_DSP_ ETAIL_STATUS “A” = Active set
CS “M” = Monitored set
“D” = Detected set
“U” = Undetected
“N” = Not listed or detected
f WCDM FTD_SB_WDSP_CELL_D S R,I,O Cell syncronization status:
A_DSP_ ETAIL_SYNC “N” = Not syncronized,
CS “S” = Syncronized
“D” = SFN Decoded

g WCDM FTD_SB_WDSP_CELL_D S R,I,O Cell tx diversity status:

A_DSP_ ETAIL_STTD “-” = STTD not used on PCCPCH
CS “S” = STTD used on PCCPCH.
h(5) WCDM FTD_SB_WDSP_CELL_D W:D R,I,O Cell frame timing in relation to
A_DSP_ ETAIL_TIMING WCDMA system clock.
CS
I WCDM FTD_SB_WDSP_CELL_D S R,I,O SCPICH measurement status:
A_DSP_ ETAIL_SCPICH “-” = SCPICH not used
CS “S” = SCPICH used
j(3) WCDM FTD_SB_WDSP_CELL_D W:D R,I,O EcNo * -10
A_DSP_ ETAIL_H
CS
k(4) WCDM FTD_SB_WDSP_CELL_D W:D R,I,O RSCP * -10
A_DSP_ ETAIL_G
CS
 SPECIFICATION 151 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Groups 42-45: WCDMA Layer 1 Field Test Displays

To be defined.
 SPECIFICATION 152 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 46: WCDMA RAN System displays

Display Display 46.01: RRC Global Status (Version: 6.2, Status: Approved)

This screen shows Global RRC status

Data Display:

+++++++++++++++++++++++++++
+ RRC Global status +
+ +
+ Global state aaaaaaaaa +
+ Active Domain CS: b +
+ Active Domain PS: c +
+ Drop cause dddddddddddd +
+ Ciphering CS e +
+ Ciphering PS f +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(9) PN_WRA FTD_SB_RRC_GLOBAL_STATE S R,O RRC Global State OOZ, idle-
N pch, cell-dch, cell-fach, cell-pch,
ura-pch
b(1) PN_WRA FTD_SB_RRC_GLOBAL_ACTIVE_DO B:D R,O RRC Active Domain - CS 1/0
N MAIN_CS
c(1) PN_WRA FTD_SB_RRC_GLOBAL_ACTIVE_DO B:D R,O RRC Active Domain - PS 1/0
N MAIN_PS
d(12) PN_WRA FTD_SB_RRC_CALL_RELEASE_DR S R,O Last Call Drop/Release Cause
N OP_CAUSE
e(1) PN_WRA FTD_SB_RRC_CS_DOMAIN_CIPHER B:D R,O Ciphering - CS Domain on/off -
N ING 1/0
f(1) PN_WRA FTD_SB_RRC_PS_DOMAIN_CIPHER B:D R,O Ciphering - PS Domain on/off -
N ING 1/0

Display 46.02: PEER message MSC (Version: 6.2, Status: Approved)

This screen shows an MSC of last 7 PEER messages Message order runs vertically. The
oldest message is blanked out.

ASUp - Active Set Update (C - Complete, F - Failure)

ADD - Assistance Data Delivery CCO - Cell Change Order From UTRAN (F - Failure)

CU - Cell Update (Cnf - Confirm)

CtCk - Counter Check (R - Response)

HOFU - Handover From UTRAN Command (F - Failure)

 SPECIFICATION 153 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

HOTU - Handover To UTRAN Command (C - Complete)

IRHI - Inter RAT Handover Info

MeCn - Measurement Control (F - Failure)

PAGEx - Paging Type x

PCRc - Physical Channel Reconfiguration (C - Complete, F - Failure)

PSCA - Physical Shared Channel Allocation

PCRq - PUSCH Capacity Request

RBRc - Radio Bearer Reconfiguration (C - Complete, F - Failure)

RBRl - Radio Bearer Release (C - Complete, F - Failure)

RBSt - Radio Bearer Setup (C - Complete, F - Failure)

RCRej - RRC Connection Reject

RCRl - RRC Connection Release (C - Complete)

RCReq - RRC Connection Request

RCSt - RRC Connection Setup (C - Complete)

RFI - RRC Failure Info

RS - RRC Status

SecM - Security Mode Command (C - Complete, F - Failure)

SgCR - Signalling Connection Release (I - Indication)

SICI - System Information Change Indication

TCRc - Transport Channel Reconfiguration (C - Complete, F - Failure)

TFCC - Transport Format Combination Control (F - Failure)

UECEq - UE Capability Enquiry

UECI - UE Capability Information (C - Confirm)

UPCC - Uplink Physical Channel Control

UraU - URA Update (C - Confirm)

UMI - UTRAN Mobility Information (C - Confirm, F - Failure)

Data Display:

+++++++++++++++++++++++++++
+ PEER message MSC +
 SPECIFICATION 154 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ PEER message ID aaaaa +

+ PEER message ID bbbbb +
+ PEER message ID ccccc +
+ PEER message ID ddddd +
+ PEER message ID eeeee +
+ PEER message ID fffff +
+ PEER message ID ggggg +
+ PEER message ID hhhhh +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(5) PN_WRA FTD_SB_RRC_PEER_MSG_1_ID S R,O PEER Message ID
N
e(5) PN_WRA FTD_SB_RRC_PEER_MSG_5_ID S R,O PEER Message ID
N
b(5) PN_WRA FTD_SB_RRC_PEER_MSG_2_ID S R,O PEER Message ID
N
f(5) PN_WRA FTD_SB_RRC_PEER_MSG_6_ID S R,O PEER Message ID
N
c(5) PN_WRA FTD_SB_RRC_PEER_MSG_3_ID S R,O PEER Message ID
N
g(5) PN_WRA FTD_SB_RRC_PEER_MSG_7_ID S R,O PEER Message ID
N
d(5) PN_WRA FTD_SB_RRC_PEER_MSG_4_ID S R,O PEER Message ID
N
h(5) PN_WRA FTD_SB_RRC_PEER_MSG_8_ID S R,O PEER Message ID
N

Display 46.03: RNTI Values (Version: 6.2, Status: Approved)

This screen shows current RNTI values

Data Display:

+++++++++++++++++++++++++++
+ RNTI values +
+ +
+ USRNC identity aaa +
+ USRNTI bbbbb +
+ C-RNTI cccc +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_U_RNTI_SRNC_IDE W:H R,O U-RNTI SRNC Identity 0..FFF
N NTITY
 SPECIFICATION 155 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

b(5) PN_WRA FTD_SB_RRC_U_RNTI_SRNTI DW:H R,O U-RNTI SRNTI 0..FFFFF

N
c(4) PN_WRA FTD_SB_RRC_C_RNTI W:H R,O C-RNTI 0..FFFF
N

Display 46.04: Ciphering Capability (Version: 6.2, Status: Approved)

This screen is used to set and display the Ciphering capability - possible inputs are shown
on the help text

Data Display:

+++++++++++++++++++++++++++
+ Ciphering capability +
+ +
+ UEA0 ciphering: +
+ aaaaaaaa +
+ +
+ UEA1 ciphering: +
+ bbbbbbbb +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Format Mod Description

. e
INPU PN_WRA FTD_SB_INPUT_rrc_ftd_flag_uea_ DW:D R,O callback function subblock identity
T N ciphering_capability
a(8) PN_WRA FTD_SB_RRC_UEA0_CIPHER_FL S R,O Ciphering capability flag to show if
N AG UEA0 is ENABLED or DISABLED
b(8) PN_WRA FTD_SB_RRC_UEA1_CIPHER_FL S R,O Ciphering capability flag to show if
N AG UEA1 is ENABLED or DISABLED

Display 46.05: Cell Selection - Screen 2 (Version: 6.2, Status: Approved)

This screen shows the current PLMN information

Data Display:

+++++++++++++++++++++++++++
+ Cell selection - 2 +
+ +
+ PLMN number aaaaaa +
+ Search type bbbbbb +
+ Trigger type cccccc +
+ PLMN frequency ddddd +
+ PLMN scramble code eee +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 156 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mod Description

. t e
a(6) PN_WRA FTD_SB_RRC_PLMN_NUMBER DW:H R,O PLMN Number - 0..FFFFFF
N
b(6) PN_WRA FTD_SB_RRC_PLMN_SEARCH_TY S R,O Type of search used to find PLMN
N PE nonini, init, candid, allcel, emerge,
PLMN
c(6) PN_WRA FTD_SB_RRC_PLMN_SEARCH_TR S R,O Type of trigger used to find PLMN
N IGGER - L1trig, statch, intRat
d(5) PN_WRA FTD_SB_RRC_PLMN_FREQ W:D R,O PLMN frequeny
N
e(3) PN_WRA FTD_SB_RRC_PLMN_SCR_CODE W:D R,O PLMN scramble code
N

Display 46.06: FDD BTS Carrier Lock Mode (Version: 6.2, Status: Approved)

This screen is used in BTS carrier lock mode to retrieve FDD Frequency and Scrambling
code. The frequency and scrambling code is entered as one decimal value. Both frequency
and scrambling code are five digits. e.g. entered value on FTD is '1060000040', where
'10600' is the BTS test frequency and '00040' is the test scrambling code. To clear the BTS
test mode user enters '0000000000'.

Data Display:

+++++++++++++++++++++++++++
+ FDD BTS carrier lock +
+ mode +
+ +
+ FDD frequency: +
+ aaaaa +
+ +
+ FDD scrambling code: +
+ bbbbb +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_rrc_ftd_wcdma_bts_freq_l DW:D R,O callback function subblock
T N ock_mode identity
a(5) PN_WRA FTD_SB_RRC_BTS_CARRIER_LOCK_FR W:D R,O FDD Frequency to use in
N EQ BTS carrier lock mode
b(5) PN_WRA FTD_SB_RRC_BTS_CARRIER_LOCK_SC W:D R,O FDD scrambling code to
N R_CODE use in BTS carrier lock
mode

Display 46.07: Counter Reset (Version: 6.2, Status: Approved)

This screen is used to reset counters

Data Display:
 SPECIFICATION 157 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++
+ Counter reset +
+ +
+ Reset all counters 1 +
+ Quit 0 +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_rrc_ftd_reset_count DW:D R,O callback function subblock identity
T N ers

Display 46.08: Call Failure Reasons (Version: 6.2, Status: Approved)

This screen shows Counts for each call failure reason

Data Display:

+++++++++++++++++++++++++++
+ Call failure +
+ reason +
+ +
+ RLink aaa Handover bbb +
+ RLC ccc Uplayer ddd +
+ Normal eee RLC/SIB7 fff +
+ Config ggg V/N300 hhh +
+ CRT iii V/N300 jjj +
+ OoS kkk Unspec lll +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_RADIO_LINK_FAILURE W:D R,O Number of Radio link Failures
N _COUNT
b(3) PN_WRA FTD_SB_RRC_HO_FROM_UTRAN_C W:D R,O Number of Handover to
N OUNT UTRAN
c(3) PN_WRA FTD_SB_RRC_RLC_LINK_ERROR_CO W:D R,O Number of RLC link Error
N UNT
d(3) PN_WRA FTD_SB_RRC_RELEASE_REQ_COUN W:D R,O Number of upper layer
N T triggered release
e(3) PN_WRA FTD_SB_RRC_NORMAL_REL_COUNT W:D R,O Number of normal release
N
f(3) PN_WRA FTD_SB_RRC_SIB7_RECEPTION_FAI W:D R,O Number of RLC link Error
N L_COUNT
g(3) PN_WRA FTD_SB_RRC_CONFIG_FAILURE_CO W:D R,O Number of configuration
N UNT failures
 SPECIFICATION 158 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

h(3) PN_WRA FTD_SB_RRC_V300_GR_N300_COUN W:D R,O Number of V300 > N300

N T failures
i(3) PN_WRA FTD_SB_RRC_T314_T315_TIMEOUT_ W:D R,O Number of Connection
N COUNT Reestablishment Timers
Timeouts failures-T314/T315
j(3) PN_WRA FTD_SB_RRC_V302_GR_N302_COUN W:D R,O Number of V302 > N302
N T failures
k(3) PN_WRA FTD_SB_RRC_T316_T317_T307_COU W:D R,O Number of Out of Service
N NT Timer Timeout failures-
T316/T317/T307
l(3) PN_WRA FTD_SB_RRC_UNSPECIFIC_FAILURE W:D R,O Number of unspecific failures
N _COUNT

Display 46.09: L1 State (Version: 6.2, Status: Approved)

This screen shows L1 State

Data Display:

+++++++++++++++++++++++++++
+ L1 state +
+ +
+ PCCPCH state a +
+ SCCPCH state b +
+ RACH state c +
+ DPCH state d +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(1) PN_WRA FTD_SB_RRC_PCCPCH_STATE B:D R,O PCCPCH State
N
b(1) PN_WRA FTD_SB_RRC_SCCPCH_STATE B:D R,O SCCPCH State
N
c(1) PN_WRA FTD_SB_RRC_RACH_STATE B:D R,O RACH State
N
d(1) PN_WRA FTD_SB_RRC_DPCH_STATE B:D R,O DPCH State
N

Display 46.10: Cell Reselection - Screen 1 (Version: 6.2, Status: Approved)

This screen shows reselection OK and Fail counters

Data Display:

+++++++++++++++++++++++++++
+ Cell reselection - 1 +
+ Idle OK / Failed +
+ aaaaa bbbbb +
 SPECIFICATION 159 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Connected OK / Failed +
+ ccccc ddddd +
+ UMTS => GSM OK / FAILED +
+ eeeee fffff +
+ GSM => UMTS OK / FAILED +
+ ggggg hhhhh +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(5) PN_WRA FTD_SB_RRC_IDLE_RESELECTION_OK_ W:D R,O Number of successful Idle
N COUNT mode reselections
b(5) PN_WRA FTD_SB_RRC_IDLE_RESELECTION_FAI W:D R,O Number of unsuccessful
N L_COUNT Idle mode reselections
c(5) PN_WRA FTD_SB_RRC_CON_RESELECTION_OK_ W:D R,O Number of successful
N COUNT Connected mode
reselections
d(5) PN_WRA FTD_SB_RRC_CON_RESELECTION_FAI W:D R,O Number of unsuccessful
N L_COUNT Connected mode
reselections
e(5) PN_WRA FTD_SB_RRC_UMTS_TO_GSM_OK_COU W:D R,O Number of successful
N NT UMTS to GSM reselections
f(5) PN_WRA FTD_SB_RRC_UMTS_TO_GSM_FAIL_CO W:D R,O Number of unsuccessful
N UNT UMTS to GSM reselections
g(5) PN_WRA FTD_SB_RRC_GSM_TO_UMTS_OK_COU W:D R,O Number of successful GSM
N NT to UMTS reselections
h(5) PN_WRA FTD_SB_RRC_GSM_TO_UMTS_FAIL_CO W:D R,O Number of unsuccessful
N UNT GSM to UMTS reselections

Display 46.11: Radio Access Bearer Information (Version: 6.2, Status: Approved)

This screen shows Radio Access Bearers currently setup

Data Display:

+++++++++++++++++++++++++++
+ RAB information +
+ RAB ID Domain +
+ aaa b +
+ ccc d +
+ eee f +
+ ggg h +
+ iii j +
+ kkk l +
+ SRB’s ID mm nn oo pp +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_RAB_ID1 B:D R,O Radio Access Bearer ID
N
 SPECIFICATION 160 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

b(1) PN_WRA FTD_SB_RRC_RAB_ID1_DOMAIN S R,O Domain - PS, CS

N
c(3) PN_WRA FTD_SB_RRC_RAB_ID2 B:D R,O Radio Access Bearer ID
N
d(1) PN_WRA FTD_SB_RRC_RAB_ID2_DOMAIN S R,O Domain - PS, CS
N
e(3) PN_WRA FTD_SB_RRC_RAB_ID3 B:D R,O Radio Access Bearer ID
N
f(1) PN_WRA FTD_SB_RRC_RAB_ID3_DOMAIN S R,O Domain - PS, CS
N
g(3) PN_WRA FTD_SB_RRC_RAB_ID4 B:D R,O Radio Access Bearer ID
N
h(1) PN_WRA FTD_SB_RRC_RAB_ID4_DOMAIN S R,O Domain - PS, CS
N
i(3) PN_WRA FTD_SB_RRC_RAB_ID5 B:D R,O Radio Access Bearer ID
N
j(1) PN_WRA FTD_SB_RRC_RAB_ID5_DOMAIN S R,O Domain - PS, CS
N
k(3) PN_WRA FTD_SB_RRC_RAB_ID6 B:D R,O Radio Access Bearer ID
N
l(1) PN_WRA FTD_SB_RRC_RAB_ID6_DOMAIN S R,O Domain - PS, CS
N
m(2) PN_WRA FTD_SB_RRC_SRB_ID1 B:D R,O Signalling Radio Bearer ID
N
n(2) PN_WRA FTD_SB_RRC_SRB_ID2 B:D R,O Signalling Radio Bearer ID
N
o(2) PN_WRA FTD_SB_RRC_SRB_ID3 B:D R,O Signalling Radio Bearer ID
N
p(2) PN_WRA FTD_SB_RRC_SRB_ID4 B:D R,O Signalling Radio Bearer ID
N

Display 46.12: Radio Bearer Information (Version: 6.2, Status: Approved)

This screen shows all Radio Bearers associated with a RAB id. The RAB id and the
associated domain are entered as a single decimal value. The RAB id is the first three
digits and the domain is input as the last digit, 1 for PS and 0 for CS.

Data Display:

+++++++++++++++++++++++++++
+ RB information - 1 +
+ +
+ RAB ID and domain(P/C): +
+ aaab +
+ +
+ Radio Bearer ID +
+ cc dd ee ff gg hh ii jj +
+ Re-establishment timer +
+ kkkkk +
+++++++++++++++++++++++++++
 SPECIFICATION 161 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_rrc_ftd_rab_id_set DW:D R,O callback function subblock identity
T N
a(3) PN_WRA FTD_SB_RRC_RAB_ID B:D R,O Radio Access Bearer ID
N
b(1) PN_WRA FTD_SB_RRC_RAB_ID_DOMAIN S R,O Domain - PS, CS
N
c(2) PN_WRA FTD_SB_RRC_RB_ID1 B:D R,O Radio Bearer ID
N
d(2) PN_WRA FTD_SB_RRC_RB_ID2 B:D R,O Radio Bearer ID
N
e(2) PN_WRA FTD_SB_RRC_RB_ID3 B:D R,O Radio Bearer ID
N
f(2) PN_WRA FTD_SB_RRC_RB_ID4 B:D R,O Radio Bearer ID
N
g(2) PN_WRA FTD_SB_RRC_RB_ID5 B:D R,O Radio Bearer ID
N
h(2) PN_WRA FTD_SB_RRC_RB_ID6 B:D R,O Radio Bearer ID
N
i(2) PN_WRA FTD_SB_RRC_RB_ID7 B:D R,O Radio Bearer ID
N
j(2) PN_WRA FTD_SB_RRC_RB_ID8 B:D R,O Radio Bearer ID
N
k(5) PN_WRA FTD_SB_RRC_RAB_RE_EST_TIME S R,O Radio Access Bearer Re-
N R establishment Timer (T314/T315)

Display 46.13: Radio Bearer Information (Version: 6.2, Status: Approved)

This screen takes an input Radio Bearer id and shows associated information

Data Display:

+++++++++++++++++++++++++++
+ RB information - 2 +
+ +
+ RB ID: aa +
+ +
+ Domain bbbbb +
+ Re-establishment ccccc +
+ RB status ddddd +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_rrc_ftd_rb_id_set DW:D R,O callback function subblock identity
T N
a(2) PN_WRA FTD_SB_RRC_RB_ID B:D R,O Radio Bearer ID
N
b(5) PN_WRA FTD_SB_RRC_RB_DOMAIN S R,O Domain - PS, CS, SRB
N
c(5) PN_WRA FTD_SB_RRC_RB_RE_EST_TIMER S R,O Radio Bearer Re-establishment
N Timer (T314/T315)
 SPECIFICATION 162 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

N Timer (T314/T315)
d(5) PN_WRA FTD_SB_RRC_RB_STATUS S R,O RB Status - Start, Stop
N

Display 46.14: DPCH Change Count (Version: 6.2, Status: Approved)

Display number of successful HHOs and channel reconfigurations

Data Display:

+++++++++++++++++++++++++++
+ DPCH change count +
+ +
+ HHO count aaa +
+ DPCH reconf count bbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_SUCCESSFUL_HHOS B:H R Number of successful HHOs
N
b(3) PN_WRA FTD_SB_SUCCESSFUL_DPCH_REC B:H R Number of successful DPCH
N ONFIGS reconfigs

Display 46.15: Tracker Feature Enable/Disable (Version: 6.2, Status: Approved)

Sets Forced InterSystem Mode - IS resel fail, ISHO blind/fallback and CCO blind/fallback

Data Display:

+++++++++++++++++++++++++++
+ Tracker feature on/off +
+ +
+ Tracker feature +
+ enable/disable +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
 SPECIFICATION 163 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

. t e
INPU PN_WRA FTD_SB_INPUT_WPH_SET_IS_MO DW:D R callback function subblock identity
T N DE

Display 46.27: Voice RLC-U Information (Version: 6.2, Status: Approved)

This screen shows Voice RLC-U information. This includes the number of RB's used,
whether or not DTX is supported and the Frame Rate

Data Display:

+++++++++++++++++++++++++++
+ Voice RLC-U info +
+ +
+ Radio Bearer a +
+ DTX b +
+ Frame rate cc.dd +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(1) PN_WRA FTD_SB_W_MAC_VOICE_NUMBER_O B:D R This parameter reflects the
N F_RADIO_BEARERS_USED number of radio bearers used.
This will have a range of 1-3
and is represented as a single
digit decimal value
b(1) PN_WRA FTD_SB_W_MAC_VOICE_DTX_SUPP B:D R This Boolean flag shows
N ORTED whether DTX is supported or
not. This is represented as a
single digit decimal value as
follows: 0 - DTX Not Supported
1 - DTX Supported
c(2) PN_WRA FTD_SB_W_MAC_VOICE_FRAME_RA W:D R This field shows the voice
N TE_WHOLE_PART frame rate representing the
whole part of the 3-digit frame
rate which is represented as a
single digit decimal value. It
may represent the whole part
of one of the following valid
frame rate values: 4.57, 5.15,
5.90, 6.70, 7.40, 7.95, 10.2,
12.2
d(2) PN_WRA FTD_SB_W_MAC_VOICE_FRAME_RA W:D R This field shows the voice
N TE_FRAC_PART frame rate representing the
fractional part of the 3-digit
frame rate which is
represented as a 2 digit
decimal value. It may
represent the fractional part of
one of the following valid frame
 SPECIFICATION 164 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

rate values: 4.57, 5.15, 5.90,

6.70, 7.40, 7.95, 10.2, 12.2

Display 46.28: DTX Enable/Disable input (Version: 6.2, Status: Approved)

This screen shall form the input to Enable or Disable DTX

Data Display:

+++++++++++++++++++++++++++
+ DTX enable/disable +
+ input +
+ +
+ DTX enable/disable +
+ (1/0): a +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_DTX_ENABLE_DISABL DW:D R callback function subblock
T N E identity
a(1) PN_WRA FTD_SB_W_MAC_DTX_ENABLE_DISAB B:D R This screen require a single
N LE_INPUT digit decimal input to either
enable or disable DTX. This
may be done by entering the
digit 1 or 0, having the
following effect: 0 - Disable
DTX 1 - Enable DTX

Display 46.60: 3G to 2G Reselections (Version: 6.2, Status: Approved)

This is used to display information helpful in analysing 3G to 2G reselections

Data Display:

+++++++++++++++++++++++++++
+ 3G to 2G reselections +
+ +
+ Scrambling aaa ECNO bbb +
+ Inter-RAT new cell ccc +
+ ARFCN dddd verify k +
+ RSSI eee Mode State j +
+ GSM sui OK/FAIL fff ggg +
+ GSM res OK/FAIL hhh iii +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 165 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_PRI_SCR_CODE_TYPE W:D R Primary Scrambling Code
N
b(3) PN_WRA FTD_SB_ECNO_VALUE B:D R ECNO Value
N
c(3) PN_WRA FTD_SB_NEW_RAT_CELL_IND_CO B:D R Count of inter-RAT new cell inds
N UNT
d(4) PN_WRA FTD_SB_GSM_ARFCN0 W:D R Strongest GSM ARFCN
N
e(3) PN_WRA FTD_SB_STATUS_RSSI0 W:D R Status RSSI level
N
k(1) PN_WRA FTD_SB_VERIFICATION_STATUS B:D R 0 indicates that the ARFCN is not
N verified, 1 indicates that the
ARFCN is verified
f(3) PN_WRA FTD_SB_SUCCESS_GSM_SUITABI B:D R Count of Successfull GSM
N LITY_CHECK_COUNT Suitability Checks
g(3) PN_WRA FTD_SB_FAILED_GSM_SUITABILIT B:D R Count of failed GSM Suitability
N Y_CHECK_COUNT Checks
h(3) PN_WRA FTD_SB_SUCCESS_GSM_INTER_ B:D R Count of successful GSM inter-
N RESELECTION_COUNT RAT reselections
i(3) PN_WRA FTD_SB_FAILED_GSM_INTER_RE B:D R Count of failed GSM inter-RAT
N SELECTION_COUNT reselections
j(1) PN_WRA FTD_SB_MODE_STATE W:D R 0 indicates 3G selected cell, 1
N indicates 2G selected state

Display 46.61: 3G to 2G ISHO #1 (Version: 6.2, Status: Approved)

This is used to display information helpful in analysing 3G to 2G ISHO

Data Display:

+++++++++++++++++++++++++++
+ 3G to 2G ISHO - 1 +
+ +
+ Scrambling aaa ECNO bbb +
+ Comp c ARFCN dddd ver k +
+ RSSI eee Mode state j +
+ Handover Ok fff +
+ Handover Fail ggg +
+ Handover OK fall hhh +
+ Handover Fail fall iii +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_PRI_SCR_CODE_TYPE W:D R Primary Scrambling Code
N
b(3) PN_WRA FTD_SB_ECNO_VALUE B:D R ECNO Value
N
c(1) PN_WRA FTD_SB_CM_STATUS B:D R Status of compressed mode
N patterns for RSSI, Initial BSIC
verification & BSIC refresh
d(4) PN_WRA FTD_SB_GSM_ARFCN0 W:D R Strongest GSM ARFCN
N
 SPECIFICATION 166 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

N
e(3) PN_WRA FTD_SB_STATUS_RSSI0 W:D R Status RSSI level
N
k(1) PN_WRA FTD_SB_VERIFICATION_STATUS B:D R 0 indicates that the ARFCN is not
N verified, 1 indicates that the
ARFCN is verified
f(3) PN_WRA FTD_SB_SUCCESS_HO_ATTEMPS B:D R Count of succesful handover
N attemps
g(3) PN_WRA FTD_SB_FAILED_HO_ATTEMPS B:D R Count of failed handover attemps
N
h(3) PN_WRA FTD_SB_SUCCESS_FALLBACK_A B:D R Count of succesful fallback
N TTEMPS attemps
i(3) PN_WRA FTD_SB_FAILED_FALLBACK_ATTE B:D R Count of failed fallback attemps
N MPS
j(1) PN_WRA FTD_SB_MODE_STATE W:D R 0 indicates 3G selected cell, 1
N indicates 2G selected state

Display 46.62: 3G to 2G ISHO #2 (Version: 6.2, Status: Approved)

List of strongest GSM cells containing ARFCN, verification status, RSSI level

Data Display:

+++++++++++++++++++++++++++
+ 3G to 2G ISHO - 2 +
+ AFCN0 RSSI0 Verified +
+ aaaa bbb i +
+ AFCN1 RSSI1 Verified +
+ cccc ddd j +
+ AFCN2 RSSI2 Verified +
+ eeee fff k +
+ AFCN3 RSSI3 Verified +
+ gggg hhh l +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(4) PN_WRA FTD_SB_GSM_ARFCN0 W:D R Strongest GSM ARFCN
N
b(3) PN_WRA FTD_SB_STATUS_RSSI0 W:D R Status RSSI level
N
i(1) PN_WRA FTD_SB_VERIFICATION_STATUS B:D R 0 indicates that the ARFCN is not
N verified, 1 indicates that the
ARFCN is verified
c(4) PN_WRA FTD_SB_GSM_ARFCN1 W:D R Strongest GSM ARFCN 1
N
d(3) PN_WRA FTD_SB_STATUS_RSSI1 W:D R Status RSSI level 1
N
j(1) PN_WRA FTD_SB_VERIFICATION_STATUS1 B:D R 0 indicates the ARFCN is not
N verified, 1 indicates the ARFCN is
verified
e(4) PN_WRA FTD_SB_GSM_ARFCN2 W:D R Strongest GSM ARFCN 2
N
 SPECIFICATION 167 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

f(3) PN_WRA FTD_SB_STATUS_RSSI2 W:D R Status RSSI level 2

N
k(1) PN_WRA FTD_SB_VERIFICATION_STATUS2 B:D R 0 indicates the ARFCN is not
N verified, 1 indicates the ARFCN is
verified
g(4) PN_WRA FTD_SB_GSM_ARFCN3 W:D R Strongest GSM ARFCN 3
N
h(3) PN_WRA FTD_SB_STATUS_RSSI3 W:D R Status RSSI level 3
N
l(1) PN_WRA FTD_SB_VERIFICATION_STATUS3 B:D R 0 indicates the ARFCN is not
N verified, 1 indicates the ARFCN is
verified

Display 46.63: 3G to 2G ISHO #3 (Version: 6.2, Status: Approved)

List of strongest GSM cells containing ARFCN, verification status, RSSI level

Data Display:

+++++++++++++++++++++++++++
+ 3G to 2G ISHO - 3 +
+ AFCN4 RSSI4 Verified +
+ aaaa bbb i +
+ AFCN5 RSSI5 Verified +
+ cccc ddd j +
+ AFCN6 RSSI6 Verified +
+ eeee fff k +
+ AFCN7 RSSI7 Verified +
+ gggg hhh l +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(4) PN_WRA FTD_SB_GSM_ARFCN4 W:D R Strongest GSM ARFCN 4
N
b(3) PN_WRA FTD_SB_STATUS_RSSI4 W:D R Status RSSI level 4
N
i(1) PN_WRA FTD_SB_VERIFICATION_STATUS4 B:D R 0 indicates the ARFCN is not
N verified, 1 indicates the ARFCN is
verified
c(4) PN_WRA FTD_SB_GSM_ARFCN5 W:D R Strongest GSM ARFCN 5
N
d(3) PN_WRA FTD_SB_STATUS_RSSI5 W:D R Status RSSI level 5
N
j(1) PN_WRA FTD_SB_VERIFICATION_STATUS5 B:D R 0 indicates the ARFCN is not
N verified, 1 indicates the ARFCN is
verified
e(4) PN_WRA FTD_SB_GSM_ARFCN6 W:D R Strongest GSM ARFCN 6
N
f(3) PN_WRA FTD_SB_STATUS_RSSI6 W:D R Status RSSI level 6
N
k(1) PN_WRA FTD_SB_VERIFICATION_STATUS6 B:D R 0 indicates the ARFCN is not
N verified, 1 indicates the ARFCN is
verified
 SPECIFICATION 168 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

g(4) PN_WRA FTD_SB_GSM_ARFCN7 W:D R Strongest GSM ARFCN 7

N
h(3) PN_WRA FTD_SB_STATUS_RSSI7 W:D R Status RSSI level 7
N
l(1) PN_WRA FTD_SB_VERIFICATION_STATUS7 B:D R 0 indicates the ARFCN is not
N verified, 1 indicates the ARFCN is
verified
 SPECIFICATION 169 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 47: WCDMA RRC displays

Display 47.01: RRC Global State Change Counters (Version: 6.2, Status: Approved)

This screen shows Global RRC state Change Countes

Data Display:

+++++++++++++++++++++++++++
+ RRC global state change +
+ counters +
+ +
+ DCH => FACH aaaaa +
+ FACH => DCH bbbbb +
+ FACH => CELL_PCH ccccc +
+ FACH => URA_PCH ddddd +
+ DCH => CELL_PCH eeeee +
+ DCH => URA_PCH fffff +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(5) PN_WRA FTD_SB_RRC_DCH_TO_FACH_COU W:D R,O Number of state changes from
N NT DCH to FACH
b(5) PN_WRA FTD_SB_RRC_FACH_TO_DCH_COU W:D R,O Number of state changes from
N NT FACH to DCH
c(5) PN_WRA FTD_SB_RRC_FACH_TO_CELLPCH W:D R,O Number of state changes from
N _COUNT FACH to CELL_PCH
d(5) PN_WRA FTD_SB_RRC_FACH_TO_URAPCH_ W:D R,O Number of state changes from
N COUNT FACH to URA_PCH
e(5) PN_WRA FTD_SB_RRC_DCH_TO_CELLPCH_ W:D R,O Number of state changes from
N COUNT DCH to CELL_PCH
f(5) PN_WRA FTD_SB_RRC_DCH_TO_URAPCH_C W:D R,O Number of state changes from
N OUNT DCH to URA_PCH

Display 47.02: Counters for Timeouts - Screen 1 (Version: 6.2, Status: Approved)

This screen shows the number timeouts for RRC timers

Data Display:

+++++++++++++++++++++++++++
+ RRC count timeouts - 1 +
+ +
+ T300 T312 T301 T302 +
+ aaa bbb ccc ddd +
+ +
+ T304 T305 T307 T308 +
+ eee fff ggg hhh +
+ +
 SPECIFICATION 170 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ T309 iii +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_T300_IDLE_TIMEOUT W:D R,O T300 timeout counter
N _COUNT
b(3) PN_WRA FTD_SB_RRC_T312_IDLE_TIMEOUT W:D R,O T312 timeout counter
N _COUNT
c(3) PN_WRA FTD_SB_RRC_T301_TIMEOUT_COU W:D R,O T301 timeout counter
N NT
d(3) PN_WRA FTD_SB_RRC_T302_TIMEOUT_COU W:D R,O T302 timeout counter
N NT
e(3) PN_WRA FTD_SB_RRC_T304_TIMEOUT_COU W:D R,O T304 timeout counter
N NT
f(3) PN_WRA FTD_SB_RRC_T305_TIMEOUT_COU W:D R,O T305 timeout counter
N NT
g(3) PN_WRA FTD_SB_RRC_T307_TIMEOUT_COU W:D R,O T307 timeout counter
N NT
h(3) PN_WRA FTD_SB_RRC_T308_TIMEOUT_COU W:D R,O T308 timeout counter
N NT
i(3) PN_WRA FTD_SB_RRC_T309_TIMEOUT_COU W:D R,O T309 timeout counter
N NT

Display 47.03: Counters for Timeouts - Screen 2 (Version: 6.2, Status: Approved)

This screen shows the number timeouts for RRC timers

Data Display:

+++++++++++++++++++++++++++
+ RRC count timeouts - 2 +
+ +
+ T310 T311 T312 T313 +
+ aaa bbb ccc ddd +
+ +
+ T314 T315 T316 T317 +
+ eee fff ggg hhh +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_T310_TIMEOUT_CO W:D R,O T310 timeout counter
N UNT
b(3) PN_WRA FTD_SB_RRC_T311_TIMEOUT_CO W:D R,O T311 timeout counter
N UNT
c(3) PN_WRA FTD_SB_RRC_T312_TIMEOUT_CO W:D R,O T312 timeout counter
N UNT
d(3) PN_WRA FTD_SB_RRC_T313_TIMEOUT_CO W:D R,O T313 timeout counter
N UNT
 SPECIFICATION 171 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

e(3) PN_WRA FTD_SB_RRC_T314_TIMEOUT_CO W:D R,O T314 timeout counter

N UNT
f(3) PN_WRA FTD_SB_RRC_T315_TIMEOUT_CO W:D R,O T315 timeout counter
N UNT
g(3) PN_WRA FTD_SB_RRC_T316_TIMEOUT_CO W:D R,O T316 timeout counter
N UNT
h(3) PN_WRA FTD_SB_RRC_T317_TIMEOUT_CO W:D R,O T317 timeout counter
N UNT

Display 47.04: Peer Message Count- Screen1 (Version: 6.2, Status: Approved)

This screen shows Count for Peer Messages

Data Display:

+++++++++++++++++++++++++++
+ Peer message count - 1 +
+ +
+ MIB aaa PMIB bbb +
+ SIB1 ccc SIB2 ddd +
+ SIB3 eee PSIB3 fff +
+ SIB4 ggg PSIB4 hhh +
+ SIB5 iii SIB6 jjj +
+ SIB7 kkk SIB8 lll +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_MIB_COUNT W:D R,O MIB Message Count
N
b(3) PN_WRA FTD_SB_RRC_PMIB_COUNT W:D R,O MIB Message Count
N
c(3) PN_WRA FTD_SB_RRC_SIB1_COUNT W:D R,O SIB1 Message Count
N
d(3) PN_WRA FTD_SB_RRC_SIB2_COUNT W:D R,O SIB2 Message Count
N
e(3) PN_WRA FTD_SB_RRC_SIB3_COUNT W:D R,O SIB3 Message Count
N
f(3) PN_WRA FTD_SB_RRC_PSIB3_COUNT W:D R,O SIB3 Message Count
N
g(3) PN_WRA FTD_SB_RRC_SIB4_COUNT W:D R,O SIB4 Message Count
N
h(3) PN_WRA FTD_SB_RRC_PSIB4_COUNT W:D R,O SIB4 Message Count
N
i(3) PN_WRA FTD_SB_RRC_SIB5_COUNT W:D R,O SIB5 Message Count
N
j(3) PN_WRA FTD_SB_RRC_SIB6_COUNT W:D R,O SIB6 Message Count
N
k(3) PN_WRA FTD_SB_RRC_SIB7_COUNT W:D R,O SIB7 Message Count
N
l(3) PN_WRA FTD_SB_RRC_SIB8_COUNT W:D R,O SIB8 Message Count
N
 SPECIFICATION 172 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 47.05: Peer Message Count- Screen2 (Version: 6.2, Status: Approved)

This screen shows Peer Message Count

Data Display:

+++++++++++++++++++++++++++
+ Peer message count - 2 +
+ +
+ SIB9 aaa SIB15 ggg +
+ SIB10 bbb SIB16 hhh +
+ SIB11 ccc SIB17 iii +
+ SIB12 ddd SIB18 jjj +
+ SIB13 eee +
+ SIB14 fff +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_SIB9_COUNT W:D R,O SIB9 Message Count
N
b(3) PN_WRA FTD_SB_RRC_SIB10_COUNT W:D R,O SIB10 Message Count
N
c(3) PN_WRA FTD_SB_RRC_SIB11_COUNT W:D R,O SIB11 Message Count
N
d(3) PN_WRA FTD_SB_RRC_SIB12_COUNT W:D R,O SIB12 Message Count
N
e(3) PN_WRA FTD_SB_RRC_SIB13_COUNT W:D R,O SIB13 Message Count
N
f(3) PN_WRA FTD_SB_RRC_SIB14_COUNT W:D R,O SIB14 Message Count
N
g(3) PN_WRA FTD_SB_RRC_SIB15_COUNT W:D R,O SIB15 Message Count
N
h(3) PN_WRA FTD_SB_RRC_SIB16_COUNT W:D R,O SIB16 Message Count
N
i(3) PN_WRA FTD_SB_RRC_SIB17_COUNT W:D R,O SIB17 Message Count
N
j(3) PN_WRA FTD_SB_RRC_SIB18_COUNT W:D R,O SIB18 Message Count
N

Display 47.06: Peer Message Count-Screen3 (Version: 6.2, Status: Approved)

This screen shows Peer Message Count

Data Display:

+++++++++++++++++++++++++++
+ Peer message count - 3 +
+ Connect request aaa +
+ Connect reject bbb +
+ Connect setup ccc +
 SPECIFICATION 173 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Connect setup compl ddd +

+ Connect release eee +
+ Connect rel compl fff +
+ Paging type1 ggg +
+ Paging type2 hhh +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_CONRQ_COUNT W:D R,O RRC Connection Request
N Message Count
b(3) PN_WRA FTD_SB_RRC_CONREJ_COUNT W:D R,O RRC Connection Reject Message
N Count
c(3) PN_WRA FTD_SB_RRC_CONSET_COUNT W:D R,O RRC Connection Setup Message
N Count
d(3) PN_WRA FTD_SB_RRC_CONSC_COUNT W:D R,O RRC Connection Setup Complete
N Message Count
e(3) PN_WRA FTD_SB_RRC_CONREL_COUNT W:D R,O RRC Connection Release
N Message Count
f(3) PN_WRA FTD_SB_RRC_CNRLC_COUNT W:D R,O RRC Connection Release
N Complete Message Count
g(3) PN_WRA FTD_SB_RRC_PAGE1_COUNT W:D R,O Paging Type1 Message Count
N
h(3) PN_WRA FTD_SB_RRC_PAGE2_COUNT W:D R,O Paging Type2 Message Count
N

Display 47.07: Peer Message Count-Screen4 (Version: 6.2, Status: Approved)

This screen shows Peer Message Count

Data Display:

+++++++++++++++++++++++++++
+ Peer message count – 4 +
+ RB setup ok/fail +
+ aaa bbb ccc +
+ RB reconf ok/fail +
+ ddd eee fff +
+ RB release ok/fail +
+ ggg hhh iii +
+ Transport CH ok/fail +
+ jjj kkk lll +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_RBSET_COUNT W:D R,O Radio Bearer Setup Message
N Count
b(3) PN_WRA FTD_SB_RRC_RBSTC_COUNT W:D R,O Radio Bearer Setup Complete
N Message Count
c(3) PN_WRA FTD_SB_RRC_RBSTF_COUNT W:D R,O Radio Bearer Setup Failure
N Message Count
 SPECIFICATION 174 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

d(3) PN_WRA FTD_SB_RRC_RBRC_COUNT W:D R,O Radio Bearer Reconfiguration

N Message Count
e(3) PN_WRA FTD_SB_RRC_RBRCC_COUNT W:D R,O Radio Bearer Reconfiguration
N Complete Message Count
f(3) PN_WRA FTD_SB_RRC_RBRCF_COUNT W:D R,O Radio Bearer Reconfiguration
N Failure Message Count
g(3) PN_WRA FTD_SB_RRC_RBRL_COUNT W:D R,O Radio Bearer Release Message
N Count
h(3) PN_WRA FTD_SB_RRC_RBRLC_COUNT W:D R,O Radio Bearer Release Complete
N Message Count
i(3) PN_WRA FTD_SB_RRC_RBRLF_COUNT W:D R,O Radio Bearer Release Failure
N Message Count
j(3) PN_WRA FTD_SB_RRC_TCR_COUNT W:D R,O Transport Channel
N Reconfiguration Message Count
k(3) PN_WRA FTD_SB_RRC_TCHRC_COUNT W:D R,O Transport Channel
N Reconfiguration Complete
Message Count
l(3) PN_WRA FTD_SB_RRC_TCHRF_COUNT W:D R,O Transport Channel
N Reconfiguration Failure Message
Count

Display 47.08: Peer Message Count-Screen5 (Version: 6.2, Status: Approved)

This screen shows Peer Message Count

Data Display:

+++++++++++++++++++++++++++
+ Peer message count – 5 +
+ Physical CH ok/fail +
+ aaa bbb ccc +
+ Act set update ok/fail +
+ ddd eee fff +
+ HO to UTRAN ok/fail +
+ ggg hhh iii +
+ HO from UTRAN ok/fail +
+ jjj kkk lll +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_PCRC_COUNT W:D R,O Physical Channel Reconfiguration
N Message Count
b(3) PN_WRA FTD_SB_RRC_PCHRC_COUNT W:D R,O Physical Channel Reconfiguration
N Complete Message Count
c(3) PN_WRA FTD_SB_RRC_PCHRF_COUNT W:D R,O Physical Channel Reconfiguration
N Failure Message Count
d(3) PN_WRA FTD_SB_RRC_ASUP_COUNT W:D R,O Active Set Update Message
N Count
e(3) PN_WRA FTD_SB_RRC_ASUPC_COUNT W:D R,O Active Set Update Complete
N Message Count
f(3) PN_WRA FTD_SB_RRC_ASUPF_COUNT W:D R,O Active Set Update Failure
N Message Count
g(3) PN_WRA FTD_SB_RRC_HOTUT_COUNT W:D R,O Handover to UTRAN Message
N Count
 SPECIFICATION 175 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

N Count
h(3) PN_WRA FTD_SB_RRC_HOTUC_COUNT W:D R,O Handover to UTRAN Complete
N Message Count
i(3) PN_WRA FTD_SB_RRC_HFUG_COUNT W:D R,O Handover from UTRAN Message
N Count
j(3) PN_WRA FTD_SB_RRC_HOFUF_COUNT W:D R,O Handover from UTRAN Failure
N Message Count

Display 47.09: Peer Message Count-Screen6 (Version: 6.2, Status: Approved)

This screen shows Peer Message count

Data Display:

+++++++++++++++++++++++++++
+ Peer message count – 6 +
+ +
+ CU aaa CU confirm bbb +
+ CountChk ccc IDT ddd +
+ DL_tr eee UL_tr fff +
+ MContr ggg MCFail hhh +
+ MRep iii SecMod jjj +
+ SecModComp kkk +
+ SecModFail lll +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_CELUP_COUNT W:D R,O Cell Update Message Count
N
b(3) PN_WRA FTD_SB_RRC_CUCNF_COUNT W:D R,O Cell Update Confirm Message
N Count
c(3) PN_WRA FTD_SB_RRC_CTCK_COUNT W:D R,O Counter Check Message Count
N
d(3) PN_WRA FTD_SB_RRC_IDT_COUNT W:D R,O Initial Direct Transfer Message
N Count
e(3) PN_WRA FTD_SB_RRC_DDT_COUNT W:D R,O Downlink Direct Transfer
N Message Count
f(3) PN_WRA FTD_SB_RRC_UDT_COUNT W:D R,O Uplink Direct Transfer Message
N Count
g(3) PN_WRA FTD_SB_RRC_MECON_COUNT W:D R,O Measurement Control Message
N Count
h(3) PN_WRA FTD_SB_RRC_MECOF_COUNT W:D R,O Measurement Control Failure
N Message Count
i(3) PN_WRA FTD_SB_RRC_MEREP_COUNT W:D R,O Measurement Report Message
N Count
j(3) PN_WRA FTD_SB_RRC_SECM_COUNT W:D R,O Security Mode Command
N Message Count
k(3) PN_WRA FTD_SB_RRC_SECMC_COUNT W:D R,O Security Mode Complete
N Message Count
l(3) PN_WRA FTD_SB_RRC_SECMF_COUNT W:D R,O Security Mode Failure Message
N Count
 SPECIFICATION 176 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 47.10: Peer Message Count-Screen7 (Version: 6.2, Status: Approved)

This screen shows Peer Message Count

Data Display:

+++++++++++++++++++++++++++
+ Peer message count – 7 +
+ +
+ SG_CR mes/ind aaa bbb +
+ UE_CE URA ccc ddd +
+ RRC URA_conf eee fff +
+ UTRAN UTRAN_cf ggg hhh +
+ UTRAN_fail iii +
+ CCO_from_UTRAN jjj +
+ CCO_from_UTRAN_fail kkk +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RRC_SGCR_COUNT W:D R,O Signalling Connection Release
N Message Count
b(3) PN_WRA FTD_SB_RRC_SGCRI_COUNT W:D R,O Signalling Connection Release
N Indication Message Count
c(3) PN_WRA FTD_SB_RRC_UECEQ_COUNT W:D R,O UE Capability Enquiry Message
N Count
d(3) PN_WRA FTD_SB_RRC_URAUP_COUNT W:D R,O URA Update Message Count
N
e(3) PN_WRA FTD_SB_RRC_RRCST_COUNT W:D R,O RRC Status Message Count
N
f(3) PN_WRA FTD_SB_RRC_URAUC_COUNT W:D R,O URA Update Confirm Message
N Count
g(3) PN_WRA FTD_SB_RRC_UTMI_COUNT W:D R,O UTRAN Mobility Information
N Message Count
h(3) PN_WRA FTD_SB_RRC_UMIC_COUNT W:D R,O UTRAN Mobility Information
N Confirm Message Count
i(3) PN_WRA FTD_SB_RRC_UMIF_COUNT W:D R,O UTRAN Mobility Information
N Failure Message Count
j(3) PN_WRA FTD_SB_RRC_CCOFU_COUNT W:D R,O CellChangeOrderFromUTRAN
N message Count
k(3) PN_WRA FTD_SB_RRC_CCOFUF_COUNT W:D R,O CellChangeOrderFromUTRANFail
N ure message Count
 SPECIFICATION 177 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 48: WCDMA RLC displays

Display 48.01: Set AM Bearer ID (Version: 6.2, Status: Approved)

Set the RLC AM bearer ID for which the AM info will be displayed

Data Display:

+++++++++++++++++++++++++++
+ Set AM bearer ID +
+ +
+ Radio bearer: aa +
+ RLC SAP: bbbb +
+ RLC mode: cc +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_RLC_FTD_AM_BE DW:D R,O callback function subblock identity
T N ARER_SELECT
a(2) PN_WRA FTD_SB_RLC_FTD_SELECTED_A B:D R,O AM radio bearer for which data is
N M_RADIO_BEARER to be displayed. It is uint8 data. It
can be 1 - 32.
b(4) PN_WRA FTD_SB_RLC_FTD_SAP_USER S R,O RLC SAP user for selected radio
N bearer. It is string data. It can be
"RRC" or "PDCP".
c(2) PN_WRA FTD_SB_RLC_FTD_MODE S R,O RLC mode for selected radio
N bearer. It is string data. It can be
"AM" or "UM".

Display 48.02: RLC AM State information (Version: 6.2, Status: Approved)

This screen displays state information for the AM bearer selected using display 48.01

Data Display:

+++++++++++++++++++++++++++
+ RLC AM state info +
+ +
+ AM uplink status aaa +
+ AM downlink status bbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 178 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RLC_FTD_AM_UL_FLOW S R,O AM Uplink flow control status. It is
N _CTRL string data. It can be "ON" or
"OFF".
b(3) PN_WRA FTD_SB_RLC_FTD_AM_DL_FLOW S R,O AM Downlink flow control status.
N _CTRL It is string data. It can be "ON" or
"OFF".

Display 48.03: RLC AM Counters 1 (Version: 6.2, Status: Approved)

This screen displays counters for the AM bearer selected using display 48.01

Data Display:

+++++++++++++++++++++++++++
+ RLC AM counters 1 +
+ +
+ PDU Tx aaaaaa +
+ PDU ReTx bbbbbb +
+ PDU Rx cccccc +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(6) PN_WRA FTD_SB_RLC_FTD_AM_DATA_PD DW:D R Number of the transmitted AMD
N U_TXD PDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.
b(6) PN_WRA FTD_SB_RLC_FTD_AM_DATA_PD DW:D R Number of the re-transmitted
N U_RETXD AMD PDUs. It is uint32 data
displayed as 6 decimal digits. It
can be 0 - 4294967295 but
displayed 0 - 999999.
c(6) PN_WRA FTD_SB_RLC_FTD_AM_DATA_PD DW:D R Number of the received AMD
N U_RXD PDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.

Display 48.04: RLC AM Counters 2 (Version: 6.2, Status: Approved)

This screen displays counters for the AM bearer selected using display 48.01

Data Display:
 SPECIFICATION 179 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++
+ RLC AM counters 2 +
+ +
+ Ctrl PDU Tx aaaaaa +
+ Ctrl PDU Rx bbbbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(6) PN_WRA FTD_SB_RLC_FTD_AM_CTRL_PD DW:D R Number of the transmitted Control
N U_TXD PDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.
b(6) PN_WRA FTD_SB_RLC_FTD_AM_CTRL_PD DW:D R Number of the received Control
N U_RXD PDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.

Display 48.05: RLC AM Counters 3 (Version: 6.2, Status: Approved)

This screen displays counters for the AM bearer selected using display 48.01

Data Display:

+++++++++++++++++++++++++++
+ RLC AM counters 3 +
+ +
+ SDU Requested aaaaaa +
+ SDU Discarded bbbbbb +
+ SDU Acked cccccc +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(6) PN_WRA FTD_SB_RLC_FTD_AM_TX_SDU_ DW:D R Number of the requested AM Tx
N REQUESTED SDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.
 SPECIFICATION 180 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

b(6) PN_WRA FTD_SB_RLC_FTD_AM_TX_SDU_ DW:D R Number of the discarded AM Tx

N DISCARDED SDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.
c(6) PN_WRA FTD_SB_RLC_FTD_AM_TX_SDU_A DW:D R Number of the acknowledged AM
N CKED Tx SDUs. It is uint32 data
displayed as 6 decimal digits. It
can be 0 - 4294967295 but
displayed 0 - 999999.

Display 48.06: RLC AM Counters 4 (Version: 6.2, Status: Approved)

This screen displays counters for the AM bearer selected using display 48.01

Data Display:

+++++++++++++++++++++++++++
+ RLC AM counters 4 +
+ +
+ Reject PDU Data aaaaaa +
+ Reject PDU Ctrl bbbbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(6) PN_WRA FTD_SB_RLC_FTD_AM_REJECTE DW:D R Number of the rejected AMD
N D_DATA_PDUS PDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.
b(6) PN_WRA FTD_SB_RLC_FTD_AM_REJECTE DW:D R Number of the rejected AM Status
N D_CTRL_PDUS PDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.

Display 48.07: RLC AM Counters 5 (Version: 6.2, Status: Approved)

This screen displays counters for the AM bearer selected using display 48.01

Data Display:

+++++++++++++++++++++++++++
+ RLC AM counters 5 +
+ +
+ Delivered SDU aaaaaa +
 SPECIFICATION 181 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Resets bbbbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(6) PN_WRA FTD_SB_RLC_FTD_AM_DELIVERE DW:D R Number of the delivered AM
N D_SDUS SDUs. It is uint32 data displayed
as 6 decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.
b(6) PN_WRA FTD_SB_RLC_FTD_AM_NUM_OF_ DW:D R Number of times of the AM resets.
N RESETS It is uint32 data displayed as 6
decimal digits. It can be 0 -
4294967295 but displayed 0 -
999999.

Display 48.08: RLC AM Counters 6 (Version: 6.2, Status: Approved)

This screen displays counters for the AM bearer selected using display 48.01

Data Display:

+++++++++++++++++++++++++++
+ RLC AM counters 6 +
+ +
+ AM re-establish aaaaaa +
+ AM reconfigs bbbbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(6) PN_WRA FTD_SB_RLC_FTD_AM_NUM_OF_RE DW:D R Number of times of the AM re-
N ESTABLISHMENTS establishments. It is uint32
data displayed as 6 decimal
digits. It can be 0 -
4294967295 but displayed 0 -
999999.
b(6) PN_WRA FTD_SB_RLC_FTD_AM_NUM_OF_RE DW:D R Number of times of the AM
N CONFIGS resets. It is uint32 data
displayed as 6 decimal digits.
It can be 0 - 4294967295 but
displayed 0 - 999999.
 SPECIFICATION 182 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 48.09: RLC AM Tx Buffer Occupancy (Version: 6.2, Status: Approved)

This screen displays the Tx buffer occupancy (in %) of the AM bearer selected using
display 48.01

Data Display:

+++++++++++++++++++++++++++
+ RLC AM Tx Buffer +
+ Occupancy +
+ +
+ AM Tx current aaa % +
+ AM Tx peak bbb % +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(3) PN_WRA FTD_SB_RLC_FTD_AM_TX_BFR_OC B:D R Current buffer occupancy of the
N C AM Tx buffer. It is uint8 data
displayed as 3 decimal digits. It
can be 0 - 100%.
b(3) PN_WRA FTD_SB_RLC_FTD_AM_TX_BFR_OC B:D R Peak buffer occupancy of the
N C_PEAK AM Tx buffer. It is uint8 data
displayed as 3 decimal digits. It
can be 0 - 100%.
 SPECIFICATION 183 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 49: WCDMA MAC displays

Display 49.01: Basic Radio Bearer Information (Version: 6.2, Status: Approved)

This screen shows the number of active UL and DL Radio Bearers and the RB ID Bit-Fields

Data Display:

+++++++++++++++++++++++++++
+ Basic RB information +
+ +
+ Uplink bb +
+ Sub ID1 aaaaaaaa +
+ Sub ID2 cccccccc +
+ Downlink ee +
+ Sub ID1 dddddddd +
+ Sub ID2 ffffffff +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(8) PN_WRA FTD_SB_W_MAC_UL_RB_SUB_ID_ DW:H R This field shows the Active Up-
N 1 Link Radio Bearer Id bit-
field,nSub_Id_1, as an 8 digit
hexadecimal value. This will have
a range ofn0-FFFFFFFF. When
this hex value is converted into a
bit-field, a 1 willnrepresent an
active RB for this SUB ID and 0
an inactive RB for this Sub
ID.nThe RB shall be indicated by
its position in the bit-field. e.g the
Least Significant Bit (LSB) will
represent RB 1, the Most
Significant Bit (MSB) will
represent RB 32.
b(2) PN_WRA FTD_SB_W_MAC_NUM_ACTIVE_U B:D R This field shows the number of
N L_RB active up-link radio bearers
having a range of 0-32
represented as an integer
c(8) PN_WRA FTD_SB_W_MAC_UL_RB_SUB_ID_ DW:H R This field shows the Active Up-
N 2 Link Radio Bearer Id bit-field,
Sub_Id_2, as an 8 digit
hexadecimal value. This will have
a range of 0-FFFFFFFF. When
this hex value is converted into a
bit-field, a 1 will represent an
active RB for this SUB ID and 0
an inactive RB for this Sub ID.
The RB shall be indicated by its
position in the bit-field. e.g the
Least Significant Bit (LSB) will
 SPECIFICATION 184 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

represent RB 1, the Most

Significant Bit (MSB) will
represent RB 32.
d(8) PN_WRA FTD_SB_W_MAC_DL_RB_SUB_ID_ DW:H R This field shows the Active Down-
N 1 Link Radio Bearer Id bit-field,
Sub_Id_1, as an 8 digit
hexadecimal value. This will have
a range of 0-FFFFFFFF. When
this hex value is converted into a
bit-field, a 1 will represent an
active RB for this SUB ID and 0
an inactive RB for this Sub ID.
The RB shall be indicated by its
position in the bit-field. e.g the
Least Significant Bit (LSB) will
represent RB 1, the Most
Significant Bit (MSB) will
represent RB 32.
e(2) PN_WRA FTD_SB_W_MAC_NUM_ACTIVE_D W:D R This field shows the number of
N L_RB active down-link radio
bearersnhaving a range of 0-32,
represented as an integer
f(8) PN_WRA FTD_SB_W_MAC_DL_RB_SUB_ID_ DW:H R This field shows the Active Down-
N 2 Link Radio Bearer Id bit-field,
Sub_Id_2, as an 8 digit
hexadecimal value. This will have
a range of 0-FFFFFFFF. When
this hex value is converted into a
bit-field, a 1 will represent an
active RB for this SUB ID and 0
an inactive RB for this Sub ID.
The RB shall be indicated by its
position in the bit-field. e.g the
Least Significant Bit (LSB) will
represent RB 1, the Most
Significant Bit (MSB) will
represent RB 32.

Display 49.02: Basic DCH Information (Version: 6.2, Status: Approved)

This screen shows the number of UL and DL DCH's and their corresponding DCH ID Bit-
Field

Data Display:

+++++++++++++++++++++++++++
+ Basic DCH information +
+ +
+ Uplink DCH aa +
+ DCH ID bbbbbbbb +
+ Downlink DCH cc +
+ DCH ID dddddddd +
+ Conf DCH ee +
+ Free DCH ID ffffffff +
+ +
 SPECIFICATION 185 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(2) PN_WRA FTD_SB_W_MAC_ACTIVE_UL_DC W:D R This field shows the number of
N H active up-link DCH's having a
range of 0-32, represented as an
integer
b(8) PN_WRA FTD_SB_W_MAC_ACTIVE_UL_DC DW:H R This field shows the Active Up-
N H_ID_BITFIELD Link DCH Id bit-field, as an 8 digit
hexadecimal value. This will have
a range of 0-FFFFFFFF. When
this hex value is converted into a
bit-field, a 1 will represent an
active DCH and a 0 an inactive
DCH.nThe DCH shall be indicated
by its position in the bit-field. e.g
the Least Significant Bit (LSB) will
represent DCH 1, the Most
Significant Bit (MSB) will
represent DCH 32.
c(2) PN_WRA FTD_SB_W_MAC_ACTIVE_DL_DC W:D R This field shows the number of
N H active down-link DCH's having a
range of 0-32, represented as an
integer
d(8) PN_WRA FTD_SB_W_MAC_ACTIVE_DL_DC DW:H R This field shows the Active Down-
N H_ID_BITFIELD Link DCH Id bit-field, as an 8 digit
hexadecimal value. This will have
a range of 0-FFFFFFFF. When
this hex value is converted into a
bit-field, a 1 will represent an
active DCH and a 0 an inacative
DCH. The DCH shall be indicated
by its position in the bit-field. e.g
the Least Significant Bit (LSB) will
represent DCH 1, the Most
Significant Bit (MSB) will
represent DCH 32.
e(2) PN_WRA FTD_SB_W_MAC_FREE_DCH W:D R This field shows the number of
N configured DCH's that do not
have RB's attached. This field has
a range of 0-32, represented as
an integer.
f(8) PN_WRA FTD_SB_W_MAC_FREE_DCH_ID_ DW:H R This field shows the unconnected
N BITFIELD DCH Id bit-field as an 8 digit
hexadecimal value. These are the
DCH's that are configured but no
UL or DL RB is connected to
them. When this hex value is
converted into a bit-field, a 1 will
represent an active DCH and a 0
an inacative DCH. The DCH shall
be indicated by its position in the
bit-field. e.g the Least Significant
Bit (LSB) will represent DCH 1,
the Most Significant Bit (MSB) will
represent DCH 32.
 SPECIFICATION 186 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 49.04: Radio Bearer ID and SUB ID input (Version: 6.2, Status: Approved)

This screen shall form the input for the Radio Bearer ID and sub ID. This will be formed of a
2 digit decimal value of the RB ID (XX, range 1-32) followed by a single digit for the Sub ID
(Y being either 1 or 2), input as XXY

Data Display:

+++++++++++++++++++++++++++
+ RB ID and SUB ID input +
+ +
+ Enter RB ID and SUB ID +
+ as XXY: aaa +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_RB_AND_SUBID_ DW:D R callback function subblock identity
T N SET
a(3) PN_WRA FTD_SB_W_MAC_RB_SUB_ID_INP B:D R This 3 digit decimal input requests
N UT the 2 digit RB-ID, having a range
of 0-32, followed by the single
digit Sub-ID, which can be either
1 or 2

Display 49.05: Radio Bearer Information (Version: 6.2, Status: Approved)

This screen shall display the Radio Bearer Information including both UL and DL
information

Data Display:

+++++++++++++++++++++++++++
+ RB information +
+ +
+ ActStatus aa RLC mode b +
+ RLC connect c Cipher d +
+ Priority e TCHtype f +
+ TCH_ID gg CTstat h +
+ CTvalue i Size j +
+ DEDBR kk TCHtype l +
+ ID mm status n value o +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
 SPECIFICATION 187 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

a(2) PN_WRA FTD_SB_W_MAC_RB_ACTIVE_ST S R Represents the RB's Active status

N ATUS using 2 characters.
Thesencharacters represent the
following status:nUL - Up-LinknDL
- Down-LinknUD - Up-Link and
Down-LinknNO - Representing
none of the above i.e. no active
status
b(1) PN_WRA FTD_SB_W_MAC_RB_RLC_MODE S R The RLC mode is represented by
N a single character whichnreflects
the following valid information on
the display about the RB
RLCnmode:nM - Main,nV -
VoicenC - CSDnL - Loopback
c(1) PN_WRA FTD_SB_W_MAC_RB_RLC_CONN S R This field represents the RLC
N ECTED_STATUS Connected status which
isnrepresented as a single
character and is used to represent
the followingninformationnC -
ConnectednU - Unconnected
d(1) PN_WRA FTD_SB_W_MAC_RB_CIPHERING S R This field informs us if ciphering
N _STATUS for this radio bearer isnEnabled or
Disabled. This is represented as a
single character as followsnE -
Ciphering EnablednD - Ciphering
Disabled
e(1) PN_WRA FTD_SB_W_MAC_RB_UL_PRIORIT B:D R This parameter represents the RB
N Y UL information priority as
andecimal value which has a
range of 1-8
f(1) PN_WRA FTD_SB_W_MAC_RB_UL_MAPPED S R The UL Mapped Traffic Channel
N _TCH_TYPE Type is represented as a
singlencharacter as followsnR -
RACHnD - DCH
g(2) PN_WRA FTD_SB_W_MAC_RB_UL_MAPPED W:D R This field represents the UL
N _TCH_ID Mapped TCH ID as a 2
digitndecimal value. If the UL
Mapped Traffic Channel Type is
DCH then thisnhas a range of 1-
32
h(1) PN_WRA FTD_SB_W_MAC_RB_UL_CT_STA B:D R The UL CT Status flag for the RB
N TUS is represented as a singlendigit
decimal values which shows the
following information:n0 - Not
Presentn1 - Present
i(1) PN_WRA FTD_SB_W_MAC_RB_UL_CT_VAL B:H R The UL CT Value has a range of
N UE 0-15. This is represented on
thendisplay as a single digit
Hexadecimal Value having a
range 0-F
j(1) PN_WRA FTD_SB_W_MAC_RB_UL_SIZES_S S R The Sizes Status field is
N TATUS represented as a single
characternshowing the following
information:nA - All SizesnE -
ExplicitnC - Configured
k(2) PN_WRA FTD_SB_W_MAC_RB_UL_DEDBR_ B:D R This field represents the DEDBR
N INSTANCE Instance and has the rangen0-63.
This is represented as a two digit
 SPECIFICATION 188 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

decimal value on the display

l(1) PN_WRA FTD_SB_W_MAC_RB_DL_MAPPED S R The DL Mapped Traffic Channel
N _TCH_TYPE Type or FACH is representednby
a single character which shows
the following information:nF -
FACHnD - DCH
m(2) PN_WRA FTD_SB_W_MAC_RB_DL_MAPPED W:D R If the DL Mapped traffic Channel
N _TCH_ID type is DCH then thisnfield
represents a 32 bit mapped traffic
channel ID, having a range of 1-
32.nThis is represented as a 2
digit decimal value
n(1) PN_WRA FTD_SB_W_MAC_RB_DL_CT_STA B:D R The DL CT Status flag for the RB
N TUS is represented as a singlendigit
decimal values which shows the
following information:n0 - Not
Presentn1 - Present
o(1) PN_WRA FTD_SB_W_MAC_RB_DL_CT_VAL B:H R The DL CT Value has a range of
N UE 0-15. This is represented on
thendisplay as a single digit
Hexadecimal Value having a
range 0-F

Display 49.06: Input DCH ID (Version: 6.2, Status: Approved)

This screen forms the input screen for the DCH ID in order to display the information
related to the DCH on other display screens. The input is a 2-digit decimal value with a
range of 1-32

Data Display:

+++++++++++++++++++++++++++
+ Input DCH ID +
+ +
+ Enter DCH ID(xx): aa +
+ +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_DCH_ID_SET DW:D R callback function subblock identity
T N
a(2) PN_WRA FTD_SB_W_MAC_DCH_ID_INPUT B:D R This field represents a 2 digit
N deciaml value representing the
DCH ID which has a range of 1-
32
 SPECIFICATION 189 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 49.07: DCH Information (Version: 6.2, Status: Approved)

This screen shows the UL and DL DCH information for a DCH ID

Data Display:

+++++++++++++++++++++++++++
+ DCH information +
+ UL act status SUB ID1 +
+ a bbbbbbbb +
+ UL TTI SUB ID2 +
+ cc dddddddd +
+ DL act status SUB ID1 +
+ e ffffffff +
+ DL TTI SUB ID2 +
+ gg hhhhhhhh +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(1) PN_WRA FTD_SB_W_MAC_DCH_UL_ACTIVE_ S R This field represents the DCH
N STATUS UL Active status using a single
character showing the following
information: A - ActiveI - Inactive
b(8) PN_WRA FTD_SB_W_MAC_DCH_UL_RB_SUB DW:H R This field is represented as an 8-
N ID_1 digit hexadecimal value which
represents the 32-bit bit-field of
the UL RB sub id 1
c(2) PN_WRA FTD_SB_W_MAC_DCH_UL_TTI B:D R This field represents the UL TTI
N field as a two digit decimal
value. The valid values for this
field are 10, 20, 40 and 80 ms
d(8) PN_WRA FTD_SB_W_MAC_DCH_UL_RB_SUB DW:H R This field is represented as an 8-
N ID_2 digit hexadecimal value which
represents the 32-bit bit-field of
the UL RB sub id 2
e(1) PN_WRA FTD_SB_W_MAC_DCH_DL_ACTIVE_ S R This field represents the DCH
N STATUS DL Active status using a single
character showing the following
information: A - ActiveI - Inactive
f(8) PN_WRA FTD_SB_W_MAC_DCH_DL_RB_SUB DW:H R This field is represented as an 8-
N ID_1 digit hexadecimal value which
represents the 32-bit bit-field of
the DL RB sub id 1
g(2) PN_WRA FTD_SB_W_MAC_DCH_DL_TTI B:D R This field represents the DL TTI
N field as a two digit decimal
value. The valid values for this
field are 10, 20, 40 and 80 ms
h(8) PN_WRA FTD_SB_W_MAC_DCH_DL_RB_SUB DW:H R This field is represented as an 8-
N ID_2 digit hexadecimal value which
represents the 32-bit bit-field of
the DL RB sub id 2
 SPECIFICATION 190 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved
 SPECIFICATION 191 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 50: WCDMA WPH displays

Display 50.01: WPH Connection counts (Version: 6.2, Status: Approved)

Count number of successful & unsuccessful connections. DPCH field also counts number
of fallbacks.

Data Display:

+++++++++++++++++++++++++++
+ WPH connection counts +
+ +
+ PCCPCH OK/NOK aaaa bbbb +
+ PRACH OK/NOK cccc dddd +
+ SCCPCH OK/NOK eeee ffff +
+ DPCH OK/NOK gggg iii +
+ DPCH fallback hhh +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(4) PN_WRA FTD_SB_SUCCESSFUL_PCCPCH_CON B:H R Number of successful
N NECTS PCCPCH connections
b(4) PN_WRA FTD_SB_FAILED_PCCPCH_CONNECTS B:H R Number of failed PCCPCH
N connections
c(4) PN_WRA FTD_SB_SUCCESSFUL_PRACH_CONN B:H R Number of successful
N ECTS PRACH connections
d(4) PN_WRA FTD_SB_FAILED_PRACH_CONNECTS B:H R Number of failed PRACH
N connections
e(4) PN_WRA FTD_SB_SUCCESSFUL_SCCPCH_CON B:H R Number of successful
N NECTS SCCPCH connections
f(4) PN_WRA FTD_SB_FAILED_SCCPCH_CONNECTS B:H R Number of failed SCCPCH
N connections
g(4) PN_WRA FTD_SB_SUCCESSFUL_DPCH_CONNE B:H R Number of successful DPCH
N CTS connections
h(3) PN_WRA FTD_SB_FALLBACK_DPCH_CONNECT B:H R Number of fallback DPCH
N S connections
i(3) PN_WRA FTD_SB_FAILED_FALLBACK_DPCH_C B:H R Number of failed DPCH
N ONNECTS connections

Display 50.10: WPH L1 Received Error Codes (Version: 6.2, Status: Approved)

This display presents error information (specifically, error code values) received from L1 by
WPH

Data Display:

+++++++++++++++++++++++++++
+ WPH L1 received errors +
 SPECIFICATION 192 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ +
+ Process ID aaaa +
+ L1 error type bbbb +
+ L1 error subtype cccc +
+ L1 main code dddddddd +
+ L1 extra code eeeeeeee +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(4) PN_WRA FTD_SB_WPH_L1_OS_TASK_ID W:H R Identification number of L1 o/s
N process
b(4) PN_WRA FTD_SB_WPH_L1_ERROR_TYPE W:H R L1 error type
N
c(4) PN_WRA FTD_SB_WPH_L1_ERROR_SUBTY W:H R L1 error subtype
N PE
d(8) PN_WRA FTD_SB_WPH_L1_MAIN_ERROR_ DW:H R L1 main error code
N CODE
e(8) PN_WRA FTD_SB_WPH_L1_EXTRA_ERROR DW:H R L1 extra error code
N _CODE

Display 50.11: WPH L1 Received Error Timestamp (Version: 6.2, Status: Approved)

This display presents error information (specifically, timestamps & extra information)
received from L1 by WPH

Data Display:

+++++++++++++++++++++++++++
+ WPH L1 received error +
+ timestamps +
+ +
+ DSP timestamp aaaaaaaa +
+ +
+ Additional DSP debug +
+ info +
+ bbbb cccc dddd eeee +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(8) PN_WRA FTD_SB_WPH_L1_TIMESTAMP DW:H R Error code DSP timestamp
N
b(4) PN_WRA FTD_SB_WPH_L1_EXTRA_DEBUG W:H R Additional DSP debug
N _INFO1 information
c(4) PN_WRA FTD_SB_WPH_L1_EXTRA_DEBUG W:H R Additional DSP debug
N _INFO2 information
d(4) PN_WRA FTD_SB_WPH_L1_EXTRA_DEBUG W:H R Additional DSP debug
N _INFO3 information
 SPECIFICATION 193 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

N _INFO3 information
e(4) PN_WRA FTD_SB_WPH_L1_EXTRA_DEBUG W:H R Additional DSP debug
N _INFO4 information

Display 50.12: WPH L1 PId list before error (Version: 6.2, Status: Approved)

This provides access to the PId list immediately preceeding the event which generated the
error. The user is prompted to enter the offset, where 0 corresponds to the most recently
saved PId. The specified PID is shown together with the seven immediately preceeding it (4
PID indices are shown to indicate what's on the display, and the ordering). Entering values
which are too large will result in the oldest 8 PIDs being shown.

Data Display:

+++++++++++++++++++++++++++
+ WPH L1 PID list before +
+ error +
+ +
+ PID ind PID +
+ aaaa << ii eeee +
+ bbbb << jj ffff +
+ cccc kk >> gggg +
+ dddd ll >> hhhh +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_WPH_L1_GET_PI DW:D R callback function subblock
T N D_INDEX identity
a(4) PN_WRA FTD_SB_WPH_L1_PID0 W:H R L1 Process id
N
i(2) PN_WRA FTD_SB_WPH_L1_PID_INDEX_ID1 B:D R This indicates the index of the
N value being pointed at.
e(4) PN_WRA FTD_SB_WPH_L1_PID4 W:H R L1 Process id
N
b(4) PN_WRA FTD_SB_WPH_L1_PID1 W:H R L1 Process id
N
j(2) PN_WRA FTD_SB_WPH_L1_PID_INDEX_ID2 B:D R This indicates the index of the
N value being pointed at.
f(4) PN_WRA FTD_SB_WPH_L1_PID5 W:H R L1 Process id
N
c(4) PN_WRA FTD_SB_WPH_L1_PID2 W:H R L1 Process id
N
k(2) PN_WRA FTD_SB_WPH_L1_PID_INDEX_ID3 B:D R This indicates the index of the
N value being pointed at.
g(4) PN_WRA FTD_SB_WPH_L1_PID6 W:H R L1 Process id
N
d(4) PN_WRA FTD_SB_WPH_L1_PID3 W:H R L1 Process id
N
l(2) PN_WRA FTD_SB_WPH_L1_PID_INDEX_ID4 B:D R This indicates the index of the
N value being pointed at.
h(4) PN_WRA FTD_SB_WPH_L1_PID7 W:H R L1 Process id
N
 SPECIFICATION 194 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 50.13: WPH L1 Rx signal list before error (Version: 6.2, Status: Approved)

This provides access to the Rx Signal list immediately preceeding the event which
generated the error. The user is prompted to enter the offset, where 0 corresponds to the
most recently saved Rx Signal. The specified Rx Signal is shown together with the seven
immediately preceeding it (4 indices are shown to indicate which are on the display, and
the ordering). Entering values which are too large will result in the oldest 8 Rx Signals
being shown

Data Display:

+++++++++++++++++++++++++++
+ WPH L1 Rx signal list +
+ before error +
+ +
+ ID ind ID +
+ aaaa << ii eeee +
+ bbbb << jj ffff +
+ cccc kk >> gggg +
+ dddd ll >> hhhh +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_WPH_L1_GET_RXSI DW:D R callback function subblock
T N G_INDEX identity
a(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID1 W:H R This displays an internal L1
N signal id
i(2) PN_WRA FTD_SB_WPH_L1_RX_SIGID_INDEX_I B:D R This is used as an aide-
N D1 memoire for the user; it
indicates the index of the
signal id being pointed at.
e(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID5 W:H R This displays an internal L1
N signal id
b(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID2 W:H R This displays an internal L1
N signal id
j(2) PN_WRA FTD_SB_WPH_L1_RX_SIGID_INDEX_I B:D R This is used as an aide-
N D2 memoire for the user; it
indicates the index of the
signal id being pointed at.
f(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID6 W:H R This displays an internal L1
N signal id
c(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID3 W:H R This displays an internal L1
N signal id
k(2) PN_WRA FTD_SB_WPH_L1_RX_SIGID_INDEX_I B:D R This is used as an aide-
N D3 memoire for the user; it
indicates the index of the
signal id being pointed at.
g(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID7 W:H R This displays an internal L1
N signal id
 SPECIFICATION 195 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

d(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID4 W:H R This displays an internal L1

N signal id
l(2) PN_WRA FTD_SB_WPH_L1_RX_SIGID_INDEX_I B:D R This is used as an aide-
N D4 memoire for the user; it
indicates the index of the
signal id being pointed at.
h(4) PN_WRA FTD_SB_WPH_L1_RX_SIGNALID8 W:H R This displays an internal L1
N signal id

Display 50.14: WPH L1 Tx signal list before error (Version: 6.2, Status: Approved)

This provides access to the Tx Signal list immediately preceeding the event which
generated the error. The user is prompted to enter the offset, where 0 corresponds to the
most recently saved Tx Signal. The specified Tx Signal is shown together with the seven
immediately preceeding it (4 indices are shown to indicate which are on the display, and
the ordering). Entering values which are too large will result in the oldest 8 Tx Signals being
shown

Data Display:

+++++++++++++++++++++++++++
+ WPH L1 Tx signal list +
+ before error +
+ +
+ ID ind ID +
+ aaaa << ii eeee +
+ bbbb << jj ffff +
+ cccc kk >> gggg +
+ dddd ll >> hhhh +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_WPH_L1_GET_TXSIG DW:D R callback function subblock
T N _INDEX identity
a(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID1 W:H R This displays an internal L1
N signal id
i(2) PN_WRA FTD_SB_WPH_L1_TX_SIGID_INDEX_I B:D R This is used as an aide-
N D1 memoire for the user; it
indicates the index of the
signal id being pointed at.
e(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID5 W:H R This displays an internal L1
N signal id
b(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID2 W:H R This displays an internal L1
N signal id
j(2) PN_WRA FTD_SB_WPH_L1_TX_SIGID_INDEX_I B:D R This is used as an aide-
N D2 memoire for the user; it
indicates the index of the
signal id being pointed at.
f(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID6 W:H R This displays an internal L1
N signal id
c(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID3 W:H R This displays an internal L1
N signal id
 SPECIFICATION 196 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

N signal id
k(2) PN_WRA FTD_SB_WPH_L1_TX_SIGID_INDEX_I B:D R This is used as an aide-
N D3 memoire for the user; it
indicates the index of the
signal id being pointed at.
g(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID7 W:H R This displays an internal L1
N signal id
d(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID4 W:H R This displays an internal L1
N signal id
l(2) PN_WRA FTD_SB_WPH_L1_TX_SIGID_INDEX_I B:D R This is used as an aide-
N D4 memoire for the user; it
indicates the index of the
signal id being pointed at.
h(4) PN_WRA FTD_SB_WPH_L1_TX_SIGNALID8 W:H R This displays an internal L1
N signal id

Display 50.15: WPH L1 list of previous warnings received before error (Version: 6.2, Status:
Approved)

This provides access to the previous warning list immediately preceeding the event which
generated the error. The user is prompted to enter the offset, where 0 corresponds to the
most recently saved warning. The specified warning is shown together with the one
immediately preceeding it (2 indices are shown to indicate which are on the display).
Entering values which are too large will result in the oldest warnings being shown

Data Display:

+++++++++++++++++++++++++++
+ WPH L1 list of previous +
+ warnings before error +
+ +
+ Ind ee +
+ Main error aaaaaaaa +
+ Extra error bbbbbbbb +
+ Ind ff +
+ Main error cccccccc +
+ Extra error dddddddd +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
INPU PN_WRA FTD_SB_INPUT_WPH_L1_GET_WAR DW:D R callback function subblock
T N N_INDEX identity
e(2) PN_WRA FTD_SB_WPH_L1_WARNING_INDEX_ B:D R This is used as an aide-
N ID1 memoire for the user; it
indicates the index of the
signal id being pointed at.
a(8) PN_WRA FTD_SB_WPH_L1_MAIN_ERROR_CO DW:H R This displays an internal L1
N DE1 signal id
b(8) PN_WRA FTD_SB_WPH_L1_EXTRA_ERROR_C DW:H R This displays an internal L1
N ODE1 signal id
f(2) PN_WRA FTD_SB_WPH_L1_WARNING_INDEX_ B:D R This is used as an aide-
N ID2 memoire for the user; it
 SPECIFICATION 197 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

indicates the index of the

signal id being pointed at.
c(8) PN_WRA FTD_SB_WPH_L1_MAIN_ERROR_CO DW:H R This displays an internal L1
N DE2 signal id
d(8) PN_WRA FTD_SB_WPH_L1_EXTRA_ERROR_C DW:H R This displays an internal L1
N ODE2 signal id
 SPECIFICATION 198 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 61: Common EM (Energy Management) displays

Display 61.01: Basic EM information (Version: 3.16, Status: Approved)

+++++++++++++++++++++++++++
+ EM information +
+ Version no aaaaaaaaa +
+ Battery bars b +
+ Bat sw status ccc +
+ Battery type ddd +
+ Volt / Temp eeee ffff +
+ Cap / SbyH gggg hhh +
+ ChMo / CsSt iii jjjj+
+ Carger type kkk +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(9) EM EM_SB_FTD_VERS S R EM version number:
ION Eg: 05.04.070
b(2) EM EM_SB_FTD_NUM B:D R Number of battery bars (1 to 8 decimal)
BER_OF_BAT_BAR
S
c(3) EM EM_SB_FTD_STAT S R Battery monitor SW status:
US ???
Cha = Charging
Mon = Monitoring
Rst = Restart batmon4
Set = Settle after charging
Res = Reset batmon4
Ser = Service
Sto = Stopped
Dis = Disable
d(3) EM EM_SB_FTD_BAT_ S R Battery type:
TYPE ???
SB = Service battery
Ni = Nickel battery
Err = Error
4L1 = 4.1 v littium battery
4L2 = 4.2 v littium battery
e(4) EM EM_SB_FTD_INST_ W:D R Instantaneous battery voltage in mV (0 to
BAT_VOLT 9999 decimal)
f(3) EM EM_SB_FTD_CUR W:D R Current battery temperature in kelvin (0 to
RENT_BAT_TEMP 999 decimal)
g(4) EM EM_SB_FTD_BAT_ W:D R Battery capacity in mAh (0 to 9999 decimal)
CAPACITY
h(3) EM EM_SB_FTD_REM W:D R Remaining standby time to battery low in
AIN_STBY_HOURS hours (0 to 999 decimal)
i(3) EM EM_SB_FTD_PRES S R Present charging state:
ENT_CHA_MODE Not = Not charging
Ini = Initialization
TCh = Temperature check
LiC = Lithium charging
Dis = Disabled
 SPECIFICATION 199 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Dch = Discharging
Dco = Disconnectted
Pow = Power
Col = Cold charging
Hot = Hot charging
Mai = Maintenance charging
BEr = Battery error
NiC = Nickel charging
CPa = Control paused
CDi = Control disabled
j(4) EM EM_SB_FTD_CS_S S R CS state):
TATE ????
Idle
NSPS
SCAN
SIGN = Signalling
Call
CSD
HSCS = HSCSD
GPRS
Data
EDGE
k(3) EM EM_SB_FTD_PRES S R Present charger type:
ENT_CHR_TYPE ???
TEr = Temperature error
2Wi = 2 wire charger
3Wi = 3 wire charger
AC7 = ACP7 charger
VEr = Voltage error
CEr = Current error

Display 61.02: Basic BATMON4 information (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ BATMON4 information +
+ Batt voltage aaaaa +
+ Stand by time bbbbbb +
+ TX-off Volt ccccc +
+ TX-on Volt dddd +
+ Misc flags eeeee +
+ VDmf /PowInd ffff ggg+
+ Stat/Cal V hhh iiii+
+ Blow/PrWarn jjj kkk+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(4) EM EM_SB_FTD_INST_ W:D R Measured instantaneous battery voltage in mV
BAT_VOLT (0 to 9999 decimal).
b(6) EM EM_SB_FTD_REMAI DW:D R Remaining standby time estimate in minutes (0
N_STBY_MINUTES to 999999 decimal).
c(4) EM EM_SB_FTD_EST_T W:D R Estimated Tx-Off battery voltage in mV (0 to
X_OFF 9999 decimal).
d(4) EM EM_SB_FTD_MEAS_ W:D R Measured Tx-On synchronized battery voltage
TX_ON in mV (0 to 9999 decimal).
e(2) EM EM_SB_FTD_MISC_ B:H R Miscellaneous Battery Monitor flags in bitfields
 SPECIFICATION 200 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

MON_FLAGS1 (00 to FF hexadecimal).

f(4) EM EM_SB_FTD_DMF_B W:D R Double median filtered battery voltage in mV (0
AT_VOLT to 9999 decimal)
g(3) EM EM_SB_FTD_BAT_P S R Battery Power Indication:
OW_IND "Ok"
"Low"
"LFB" (= Low For Boot)
"Emp" (= Empty)

h(3) EM EM_SB_FTD_STATU S R Battery Monitor internal status:

S "Cha" = Charging
"Mon" = Monitoring
"Rst" = Restart batmon4
"Set" = Settle after charging
"Res" = Reset batmon4
"Ser" = Service
"Stp" = Stopped
"Dis" = Disable
i(4) EM EM_SB_FTD_CALC_ W:D R Calculated voltage level "Check" voltage in mV
VOLT_LEVEL (0 to 9999 decimal).
j(3) EM EM_SB_FTD_NUMB W:D R Number of battery low warnings (0 to 999
ER_BAT_LOW_WAR decimal).
N
k(3) EM EM_SB_FTD_WARN W:D R Present warning interval counter (0 to 999
_COUNT decimal).

Display 61.03: Advanced BATMON4 algorithm information (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ Advanced BATMON4 +
+ Dmf voltage aaaa +
+ Misc int flags 1 b +
+ Curr mon est 1 ccccc +
+ Batmon4 volt ddd +
+ Misc int flags 2 e +
+ Curr mon est 2 fffff +
+ Phi/elapsed gggg hhhhhh+
+ Dphi/SbyMin iiiiijjjjjj+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Format Mod Description

e
a(4) EM EM_SB_FTD_DMF_BAT_ W:D R Double median filtered battery voltage in
VOLT mV (0 to 9999 decimal)
b EM EM_SB_FTD_MISC_MON B:H R Miscellaneous BatMon4 internal flags as 4
_INT_FLAGS2 bit bitfield (0 to F hexadecimal).
Fields (bit 0 = lsb):
[0] : First Correction flag.
[1] : Model Valid flag.
[3-2] : Settle Delay Mode.
c(5) EM EM_SB_FTD_CURRENT_ W :D R Total phone current estimate reported to
MON_EST1 the Battery Monitor by PSM module in 0.1
mV units (0 to 99999 decimal).
d(4) EM EM_SB_FTD_MON_VOLT W:D R Current BatMon4 model voltage in mV (0
to 9999 decimal).
 SPECIFICATION 201 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

e EM EM_SB_FTD_MISC_MON B:H R Misc BatMon4 internal flags as 4 bit

_INT_FLAGS3 bitfield (0 to F hexadecimal).
Bitfields (bit 0 = lsb):
[0] : 0=Standby, 1=Non-Standby.
[3-1] : <Future - TBD>.
f(5) EM_SB_FTD_CURRENT_ W :D R Total phone current (ILoad) estimated by
MON_EST2 BatMon4 in the Non-Standby algorithm
part from measured voltage drop in 0.1
mV units (0 to 99999 decimal).
g(4) EM EM_SB_FTD_PHI_VARIA W:D R Present BatMon4 algorithm Phi value in
BLE mV (0 to 9999 decimal).
h(6) EM EM_SB_FTD_ELAPSED_ DW:D R Elapsed "Model Time" in minutes (0 to
TIME 999999 decimal).
i(5) EM EM_SB_FTD_DELTA_PHI W:D R Present BatMon4 ∆Phi value in mV (-9999
_VARIABLE (Signed to +9999 signed decimal).
)
j(6) EM EM_SB_FTD_REMAIN_ST DW:D R BatMon4 remaining standby time estimate
BY_MINUTES in minutes (0 to 999999 decimal).

Display 61.04: Battery Monitor setup and log information (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ Battery monitor setup +
+ Batt impedance aaa +
+ Charged amount bbbbb +
+ Full treshold cccc +
+ Low treshold ddddd +
+ Boot voltage eeee +
+ Low warning V ffff +
+ Algorithm adj gg +
+ Algorithm err hhhh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Format Mod Description

e
a(3) EM EM_SB_FTD_BAT_IM W:D R Battery impedance in mOhm (0 to 999 decimal).
P
b(5) EM EM_SB_FTD_CHARG W:D R Charged amount (-9999 to +9999 decimal)
ED_AMOUNT (Signe
d)
c(4) EM EM_SB_FTD_BAT_F W:D R Battery full voltage threshold used by the
ULL_THRES BatMon4 algorithm in mV (0 to 9999 decimal).
d(4) EM EM_SB_FTD_BAT_L W:D R Battery low voltage threshold used by the
OW_THRES BatMon4 algorithm in mV (0 to 9999 decimal).
e(4) EM EM_SB_FTD_BAT_B W:D R "Boot" battery voltage used for Battery Monitor
OOT_VOLT initialisation in mV (0 to 9999 decimal).
f(4) EM EM_SB_FTD_VOLT_ W:D R Voltage level at first battery low warning in mV (0
AT_FIRST_BAT_LOW to 9999 decimal).
g(2) EM EM_SB_FTD_MON_A B:H R Number of BatMon4 algorithm parameter
LG_ADJ adjustments since last reset/restart of the
BatMon4 algorithm (0 to FF hexadecimal).
h(4) EM EM_SB_FTD_PARAM W:H R BatMon4 algorithm parameter error mask as
_ERRORS bitmap (0000 to FFFF hexadecimal).
 SPECIFICATION 202 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 61.05: PSM (Phone State Monitor) information 1 (Version: 3.16, Status: Approved)

+++++++++++++++++++++++++++
+ Phone State Monitor 1 +
+ +
+ Ext act MSB aaaaaaaa +
+ +
+ Ext act MSB 2 bbbbbbbb +
+ +
+ Int act LSB dddddddd +
+ +
+ Int act LSB 2 cccccccc +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Form Mode Description

. at
a(8) EM EM_SB_FTD_ACTIV S R External activity information MSB
ITY_BYTE4
nd
b(8) EM EM_SB_FTD_ACTIV S R External activity information 2 MSB
ITY_BYTE3
nd
c(8) EM EM_SB_FTD_ACTIV S R Internal activity information 2 LSB
ITY_BYTE2
d(8) EM EM_SB_FTD_ACTIV S R Internal activity information LSB
ITY_BYTE1

MSB
Bit31 = Data cable active
Bit30 = Camera active
Bit29 = Cover power active
Bit28 = Bluetooth active
Bit27-Bit17 = Not used
Bit16 = Touchpad active
Bit15 = USB active
Bit14 = Flashlight active
Bit13 = MIDI active
Bit12 = ADSP active
Bit11 = VRR active
Bit10 = IHF active
Bit9 = MP3 active
Bit8 = GPS active
Bit7 = Video active
Bit6 = Radio active
Bit5 = DC out active
Bit4 = Irda active
Bit3 = Buzzer active
Bit2 = Vibra active
Bit1 = Keyboard light active
Bit0 = Display light active
LSB
 SPECIFICATION 203 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 61.06: PSM (Phone State Monitor) information 2 (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ Phone State Monitor 2 +
+ +
+ Battery current aaaaa +
+ +
+ Phone current bbbbb +
+ +
+ Feature current ccccc +
+ +
+ Discharge mAs ddddd +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
a(5) EM EM_SB_FTD_BAT_CURRENT W:D R Battery current in mA
(Signe (-2000 to +2000 decimal)
d)
b(5) EM EM_SB_FTD_PHONE_CURRE W:D R Phone current in mA
NT (0 to 2000 decimal)
c(5) EM EM_SB_FTD_FEATURE_CUR W:D R Feature current in mA
RENT (0 to 2000 decimal)
d(5) EM EM_SB_FTD_DISCHARGE_A W:D R Discharge amount in mAs
MOUNT (0 to 2000 decimal)

Display 61.07: PSM (Phone State Monitor) information 3 (Version: 3.16, Status: Approved)

+++++++++++++++++++++++++++
+ Phone State Monitor 3 +
+ +
+ Cs idle aaa +
+ Active sw bbb +
+ Cs state cccc +
+ mCs protocol ddddd +
+ Batmon state eeeee +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(3) EM EM_SB_FTD_CS_IDLEACTIVI B:D R CS idle activity (0 to 255 decimal)
TY
b(3) EM EM_SB_FTD_ACTIVE_SW_FE B:D R Active sw features (0 to 255 decimal)
ATURE
c(4) EM EM_SB_FTD_CS_STATE S R CS state:
????
Idle
NSPS
SCAN
 SPECIFICATION 204 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

SIGN = Signalling
Call
CSD
HSCS = HSCSD
GPRS
Data
EDGE
d(5) EM EM_SB_FTD_CS_PROTOCOL S R CS protocol:
?????
GSM
TDMA
CDMA
AMPS
PDC
WCDMA
NMT
TETRA
e(5) EM EM_SB_FTD_BATMON4_STA S R Batmon4 state:
TE IDLE
TALK
FEAT
DATA
TRANS
PACKD

Display 61.08: Basic charging information (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ Basic charging +
+ Charging state aaa +
+ Charger type bbb +
+ Inst bat volt cccc +
+ Charger checks d +
+ Chr st/Chr cur eeee ffff+
+ Full/Vchar g hhhhh+
+ Ichar/PWM iiii jjj+
+ Temp/Chr time kkk lll+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(3) EM EM_SB_FTD_PRESE S R Present charging state:
NT_CHA_MODE Not = Not charging
Ini = Initialization
TCh = Temperature check
LiC = Lithium charging
Dis = Disabled
Dch = Discharging
Dco = Disconnected
Pow = Power
Col = Cold charging
Hot = Hot charging
Mai = Maintenance charging
BEr = Battery error
NiC = Nickel charging
CPa = Control paused
 SPECIFICATION 205 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

CDi = Control disabled

b(3) EM EM_SB_FTD_PRESE S R Present charger type:
NT_CHR_TYPE ???
TEr = Temperature error
2Wi = 2 wire charger
3Wi = 3 wire charger
AC7 = ACP7 charger
VEr = Voltage error
CEr = Current error
c(4) EM EM_SB_FTD_CHA_I W:D R Instantaneous battery voltage in mV (0 to 9999
NST_BAT_VOLT decimal)
d EM EM_SB_FTD_NUMBE B:D R Number of charger checks (0 to 9 decimal)
R_CHR_CHECKS
e(4) EM EM_SB_FTD_CHR_R S R Charger recognition state:
EC_STATE ????
NoCh = No charger connected
ByCk = Battery type check
BeCk = Battery temp check
CkV7 = Check VCHAR for ACP7
CkI7 = Check ICHAR from ACP7
CkI8 = Check ICHAR from ACP8 or ACP9
Ck3W = Check for 3 wire charger
MxCk = Done maximum number of charger
checks
ChPa = Charger info paused
ChDi = Charger info disabled
ChOK= Charger OK
ChNo = Charger not OK
f(4) EM EM_SB_FTD_INST_C W:D R Instantaneous charger current in mA (0 to 9999
HR_CURRENT decimal)
g EM EM_SB_FTD_BAT_F B:D R Battery full flag (0 or 1)
ULL_FLAG
h(5) EM EM_SB_FTD_AVERA W:D R Average Vchar in mV (0 to 65535 decimal)
GE_CHR_VOLT
i(4) EM EM_SB_FTD_CALC_ W:D R Calculated Ichar in mA (0 to 9999 decimal)
CHR_CURRENT
j(3) EM EM_SB_FTD_SW_P B:D R SW PWM value (0 to 255 decimal)
WM_VALUE
k(3) EM EM_SB_FTD_CURRE W:D R Current battery temperature in kelvin (0 to 999
NT_BAT_TEMP decimal)
l(4) EM EM_SB_FTD_CHA_TI W:D R Charge time in 'hhmm' format (85 minutes is e.g.
ME shown as 125)

Display 61.09: Extended charging information (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ Extended charging +
+ Pres chr type aaa +
+ Prev chr type bbb +
+ Const ch mode c +
+ Pres chr mode ddd +
+ Pr mod / Hpwm eee fff+
+ Spwm / Opwm ggg hhhh+
+ Hpwmf/Over V i jjj+
+ Bchr/ Cwpwm k lll+
+++++++++++++++++++++++++++
 SPECIFICATION 206 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
a(3) EM EM_SB_FTD_PRESE S R Present charger type:
NT_CHR_TYPE ???
TEr = Temperature error
2Wi = 2 wire charger
3Wi = 3 wire charger
AC7 = ACP7 charger
VEr = Voltage error
CEr = Current error
b(3) EM EM_SB_FTD_PREVI S R Previous charger type:
OUS_CHR_TYPE ???
TEr = Temperature error
2Wi = 2 wire charger
3Wi = 3 wire charger
AC7 = ACP7 charger
VEr = Voltage error
CEr = Current error
c EM EM_SB_FTD_CHA_M B:D R Constant Voltage Charging method (0 to 9
ODE decimal)
d(3) EM EM_SB_FTD_PRESE S R Present charging mode:
NT_CHA_MODE ???
Not = Not charging
Ini = Initialization
TCh = Temperature check
LiC = Lithium charging
Dis = Disabled
Dch = Discharging
Dco = Disconnectted
Pow = Power
Col = Cold charging
Hot = Hot charging
Mai = Maintenance charging
BEr = Battery error
NiC = Nickel charging
CPa = Control paused
CDi = Control disabled
e(3) EM EM_SB_FTD_PREVI S R Previous charging mode:
OUS_CHA_MODE ???
Not = Not charging
Ini = Initialization
TCh = Temperature check
LiC = Lithium charging
Dis = Disabled
Dch = Discharging
Dco = Disconnectted
Pow = Power
Col = Cold charging
Hot = Hot charging
Mai = Maintenance charging
BEr = Battery error
NiC = Nickel charging
CPa = Control paused
CDi = Control disabled
f(3) EM EM_SB_FTD_HW_P B:D R HW PWM value (0 to 255 decimal)
WM_VALUE
g(3) EM EM_SB_FTD_SW_P B:D R SW PWM value (0 to 255 decimal)
WM_VALUE
 SPECIFICATION 207 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

h(4) EM EM_SB_FTD_OS_PW W:D R Open switch PWM battery voltage in mV (0 to

M_BAT_VOLT 9999 decimal)
i EM EM_SB_FTD_PWM_F B:D R HW PWM frequency (0 to 3 decimal)
REQ
j(3) EM EM_SB_FTD_OVV_LI S R OVer Voltage limit
MIT ???
3v6 = 3.6 volt
5v1 = 5.1 volt
5v3 = 5.3 volt
k EM EM_SB_FTD_BUB_C B:D R Back-Up Battery charging status (0 to 2 decimal):
HARGING 0 = software control (Should not happen)
1 = disabled
2 = enabled
l(4) EM EM_SB_FTD_CS_PW W:D R Close switch PWM battery voltage in mV (0 to
M_BAT_VOLT 9999 decimal)

Display 61.10: Extended charging information 2 (Version: 3.16, Status: Approved)

+++++++++++++++++++++++++++
+ Open -dv det aaa +
+ Slow –dv det bbb +
+ -dv over time cccc +
+ Charge amount ddd +
+ Bat voltage eee +
+ Bat temp fff +
+ Fuzzy sum ggg +
+ Maint charge hhh +
+ Open dv iii +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(3) EM EM_SB_FTD_OS_DV B:D R Open switch -dv detect rule (0 to 100 decimal)
_DETECT
b(3) EM EM_SB_FTD_SLOW_ B:D R Slow -dv detect rule (0 to 100 decimal)
DV_DETECT
c(3) EM EM_SB_FTD_DV_OV B:D R -dv over time detect rule (0 to 100 decimal)
ER_TIME_DETECT
d(3) EM EM_SB_FTD_CHARG B:D R Charge amount detect rule (0 to 100 decimal)
E_AMOUNT_DETECT
e(3) EM EM_SB_FTD_BAT_V B:D R Battery voltage detect rule (0 to 100 decimal)
OLT_DETECT
f(3) EM EM_SB_FTD_BAT_T B:D R Battery temperature detect rule (0 to 100
EMP_DETECT decimal)
g(4) EM EM_SB_FTD_FUZZY W:D R Fuzzy sum (0 to 9999 decimal)
_SUM
h(3) EM EM_SB_FTD_MAINT W:D R Maintenance charging time in seconds (0 to 999
ENANCE_CHA_TIME decimal)
i(3) EM EM_SB_FTD_OS_DV W:D R Open switch dv over time in seconds (0 to 999
_OVER_TIME decimal)
 SPECIFICATION 208 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 61.11: Configuration parameters etc. (Version: 3.16, Status: Approved)

+++++++++++++++++++++++++++
+ Config parameters +
+ +
+ Time/bat bar aaaaa +
+ Bat footprint b +
+ Conf bat bars c +
+ Conf min curr ddd +
+ Conf bat sfty e(4) +
+ Conf bat emp f(4) +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(5) EM EM_SB_FTD_CALC_ W:D R Calculated time per battery bar in minutes (0 to
BAT_BAR 99999 decimal).
b(2) EM EM_SB_FTD_CONF_ B:D R Id of configured battery footprint.
BAT_FOOTPRINT
BxB = 1
BxC = 2
BxD = 3
BxN = 4
BL_4C = 11
BL_5C = 12
c EM EM_SB_FTD_CONF_ B:D R Configured number of batt. bars.
BAT_BARS
d(3) EM EM_SB_FTD_CONF_ W:D R Configured minimum standby current for least
MIN_CURRENT power consuming phone protocol suppported in
0.1 mA units (0 to 999).
e(4) EM EM_SB_FTD_CONF_ W:D R Configured Battery Monitor battery low "Safety
BAT_SAFETY_LEVEL Net" voltage level in mV (0 to 9999 decimal).
f(4) EM EM_SB_FTD_CONF_ W:D R Configured Battery Monitor "Battery Empty"
BAT_EMPTY_LEVEL voltage level in mV (0 to 9999 decimal).

Display 61.12: Varying EM information 1 (Version: 3.15, Status: Approved)

+++++++++++++++++++++++++++
+ Varying Em info 1 +
+ FT display 1 +
+ a(12) +
+ FT display 2 +
+ b(12) +
+ FT display 3 +
+ c(12) +
+ FT display 4 +
+ d(12) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(12) EM EM_SB_FTD_STRI S R Varying field test display 1
 SPECIFICATION 209 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

NG1
b(12) EM EM_SB_FTD_STRI S R Varying field test display 2
NG2
c(12) EM EM_SB_FTD_STRI S R Varying field test display 3
NG3
d(12) EM EM_SB_FTD_STRI S R Varying field test display 4
NG4

Display 61.13: Varying EM information 2 (Version: 3.15, Status: Approved)

+++++++++++++++++++++++++++
+ Varying Em info 2 +
+ FT display 5 +
+ a(12) +
+ FT display 6 +
+ b(12) +
+ FT display 7 +
+ c(12) +
+ FT display 8 +
+ d(12) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(12) EM EM_SB_FTD_STRI S R Varying field test display 5
NG5
b(12) EM EM_SB_FTD_STRI S R Varying field test display 6
NG6
c(12) EM EM_SB_FTD_STRI S R Varying field test display 7
NG7
d(12) EM EM_SB_FTD_STRI S R Varying field test display 8
NG8
 SPECIFICATION 210 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 62: Common general displays

Display 62.01: Reasons for SW resets (Version: 3.32, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Reason for sw resets +
+ +
+ Reset reason +
+ aaaaaaaaaaaa +
+ +
+ Task name bbbbbbbbbbbb +
+ System name ccccc +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(12) MON FTD_SB_LAS S R Last reset reason shown in ASCII text. The bold text on
T_RESET_R the left should be shown when HW_RESET_XXX on the
EASON right is returned:
UNKNOWN: HW_RESET_UNKNOWN,
PWR CHA:
HW_RESET_POWER_OFF_CHARGER_CONN
ECTED,
PWR KEY:
HW_RESET_POWER_OFF_KEY_PRESSED,
SW REQ:
HW_RESET_SW_RESET_REQUESTED,
INT ERR: HW_RESET_INT_ERROR,
STACK: HW_RESET_STACK_OVERFLOW,
WD REQ:
HW_RESET_WD_RESET_REQUESTED,
DIV ZERO: HW_RESET_DIV_BY_ZERO,
PRODUCT: HW_RESET_PRODUCTION_RESET,
ASSERT: HW_RESET_ASSERTION_FAILED,
UNDEF:
HW_RESET_UNDEFINED_INSTRUCTION,
IO ABORT: HW_RESET_IO_ABORT,
NULL ACC: HW_RESET_NULL_ACCESS,
ADDERR: HW_RESET_ADDRESS_ERROR,
ALIGN: HW_RESET_ALIGNMENT_ERROR,
FLASH: HW_RESET_FLASH_WRITE-
_PROTECTION
CBUS: HW_RESET_CBUS_ERROR
OFFRTC: HW_RESET_POWER_OFF_RTC
OSFATAL: HW_RESET_OS_FATAL_HANDLER
FlaBlkOF: HW_RESET_FLASH_BLOCK_-
OVERFLOW
 SPECIFICATION 211 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

ASIC WD: HW_RESET_ASIC_WD_RESET

EPOC: HW_RESET_EPOC_RESET

ADSP_START HW_RESET_ADSP_STARTUP_FAILED
ADSP RESP HW_RESET_ADSP_NO_RESPONSE
ADSP ERR HW_RESET_ADSP_ERROR
CDSP_START HW_RESET_CDSP_STARTUP_FAILED
CDSP RESP HW_RESET_CDSP_NO_RESPONSE
CDSP ERR HW_RESET_CDSP_ERROR
HW_RESET_RESERVED
Note: reset reasons are not available in string format in
some products. In that case a numeric value is shown,
see os_trace_data.txt.

b(12) MON FTD_SB_TA S R Name of running task before reset

SK_BEFORE Note: task names are not available in some products. In
_RESET that case task number is shown, see os_trace_data.txt

c(5) MON FTD_SB_SY S R Name of the active system (GSM, TDMA, CDMA,
STEM_BEFO WCDMA) before reset
RE_RESET

ADSP and CDSP reset reasons:

STARTUP_FAILED: DSP startup was attempted, but a timeout occurred
NO RESPONSE: DSP stopped responding
ERROR: DSP detected a fatal error and asked reset

Display 62.02: Counters for resets 1 (Version: 3.32, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Counters for reset 1 +
+ +
+ Unknown/Charger aa bb +
+ Power key/SW cc dd +
+ Int/Stack ee ff +
+ WD/Div gg hh +
+ AWD ii +
+ Flash block mm +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
aa MON FTD_SB_UNKNOWN_RESET W:D R UNKNOWN
bb MON FTD_SB_POFF_CHARGER_CN W:D R POWER_OFF_CHARGER_CONNE
N CTED (charger connected when
powering off)
cc MON FTD_SB_POFF_KEY W:D R POWER_OFF_KEY_PRESSED (too
fast power off/on)
dd MON FTD_SB_SW_RESET W:D R SW_RESET_REQUESTED
ee MON FTD_SB_INTERNAL_ERROR W:D R INT_ERROR
 SPECIFICATION 212 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

ff MON FTD_SB_STACK_OF_RESET W:D R STACK_OVERFLOW

gg MON FTD_SB_WATCHDOG_RESET W:D R WD_RESET_REQUESTED
hh MON FTD_SB_DIV_BY_0_RESET W:D R DIV_BY_ZERO
ll MON FTD_SB_PPC_ASIC_WD_RESE B:D R ASIC_WD_RESET
T
mm MON FTD_SB_FLASH_BLOCK_OVER W:D R FLASH_BLOCK_OVERFLOW
FLOW

Counters are stored to permanent memory.

These counters are not PPC counters, except FTD_SB_PPC_ASIC_WD_RESET

Display 62.03: Counters for resets 2 (Version: 3.19, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Counters for resets 2 +
+ +
+ Prod/As/Un aa bb cc +
+ IO/Null/Ad dd ee ff +
+ Alig/FlashWrite gg hh +
+ Cbus ii +
+ OSFatal jj +
+ Epoc mm +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
aa MON FTD_SB_PRODUCTION_RESET W:D R PRODUCTION_RESET
bb MON FTD_SB_ASSERTFAIL_RESET W:D R ASSERTION_FAILED
cc MON FTD_SB_UNDEFINSTR_RESET W:D R UNDEFINED_INSTRUCTION
dd MON FTD_SB_IO_ABORT_RESET W:D R IO_ABORT
ee MON FTD_SB_NULLPOINTER_RESET W:D R NULL_ACCESS
ff MON FTD_SB_ADDR_ERROR_RESET W:D R ADDRESS_ERROR
gg MON FTD_SB_ALIGNMENT_RESET W:D R ALIGNMENT_ERROR
hh MON FTD_SB_FLASH_WRITE_RESET W:D R FLASH_WRITE_PROTECTION
ii MON FTD_SB_CBUS_RESET W:D R CBUS_ERROR
jj MON FTD_SB_OS_FATAL_RESET W:D R OS_FATAL_HANDLER
mm MON FTD_SB_EPOC_RESET W:D R EPOC_RESET

Counters are stored to permanent memory.

These counters are not PPC counters.
 SPECIFICATION 213 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 62.04: Counters for DSP resets (Version: 3.32, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Counters for DSP resets +
+ +
+ GSM aa bb cc +
+ TDMA dd ee ff +
+ CDMA gg hh ii +
+ WCDMA jj kk ll +
+ ADSP mm nn oo +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
a(2) MON FTD_SB_GSM W:D R GSM DSP startup fail counter
DSP_STARTUP_FAILED
b(2) MON FTD_SB_GSM W:D R GSM DSP no response (dead)
DSP_NO_RESPONSE counter
c(2) MON FTD_SB_GSM DSP_ERROR W:D R GSM DSP error counter
d(2) MON FTD_SB_TDMA W:D R TDMA DSP startup fail counter
DSP_STARTUP_FAILED
e(2) MON FTD_SB_TDMA W:D R TDMA DSP no response (dead)
DSP_NO_RESPONSE counter
f(2) MON FTD_SB_TDMA DSP_ERROR W:D R TDMA DSP error counter
g(2) MON FTD_SB_CDMA W:D R CDMA DSP startup fail counter
DSP_STARTUP_FAILED
h(2) MON FTD_SB_CDMA W:D R CDMA DSP no response (dead)
DSP_NO_RESPONSE counter
i(2) MON FTD_SB_CDMA DSP_ERROR W:D R CDMA DSP error counter
j(2) MON FTD_SB_WCDMA W:D R WCDMA DSP startup fail counter
DSP_STARTUP_FAILED
k(2) MON FTD_SB_WCDMA W:D R WCDMA DSP no response (dead)
DSP_NO_RESPONSE counter
l(2) MON FTD_SB_WCDMA DSP_ERROR W:D R WCDMA DSP error counter
m(2) MON FTD_SB_ADSP_STARTUP_FAILE W:D R ADSP startup fail counter
D
n(2) MON FTD_SB_ADSP_NO_RESPONSE W:D R ADSP no response (dead) counter
o(2) MON FTD_SB_ADSP_ERROR W:D R ADSP DSP error counter

Counters are stored to permanent memory.

These counters are not PPCs.
ADSP and CDSP reset reasons:
STARTUP_FAILED: DSP startup was attempted, but a timeout occurred
NO RESPONSE: DSP stopped responding
ERROR: DSP detected a fatal error and asked reset
 SPECIFICATION 214 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 62.06: Lights status control (Version: 1, Status: Approved)

If selected, lights are always on, otherwise light status is controlled by UI.

Data Display:

+++++++++++++++++++++++++++
+ Lights status control +
+ +
+ LIGHTS XXX +
+ +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
EXE LIGHT FTD_SB_LIGHTS_TOGGLE N/A R Toggle lights on/off
xxx LIGHT FTD_SB_LIGHTS_STATUS R Status of lights (ON, OFF)

Display 62.07: Disabling R&D Test Displays (Version: 1, Status: Approved)

This display can be used to disable R&D Test Displays item from the phone main menu. To
disable displays execute this display by selecting R&D test Displays from main menu and
entering the display number to the query.

Data Display:

+++++++++++++++++++++++++++
+ R&D Test display +
+ +
+ Disable R&D test +
+ display +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
EXE GARBAGE FTD_SELECT_STATE N/A R Disable R&D Test Displays
Value: UI_FTD_DISPLAY_OFF
 SPECIFICATION 215 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 62.08: Reliability Test Display (Version: 1, Status: Approved)

This display can be used to set phone into test state for reliability stressing. To activate this
functionality execute this display by selecting R&D test Displays from main menu and
entering the display number to the query.

Data Display:

+++++++++++++++++++++++++++
+ Reliability test disp +
+ +
+ Reliability stressing +
+ on +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Message ID Forma Mode Description

t
EXE MTC MTC_STATE_REQ N/A R Set MS to test state
Value: MTC_TEST

Display 62.10: Information about MCU and DSP software versions (Version: 3.23, Status:
Approved)

Data Display:

+++++++++++++++++++++++++++
+ MCU and DSP info +
+ +
+ MCU version aaaaa +
+ MCU date bbbbbb +
+ MCU CheckSum cccc +
+ +
+ DSP version +
 SPECIFICATION 216 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ dddddddddddd +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(5) INFO FTD_SB_MCU_VERSION R Version number of MCU SW (e.g. 2.081)

b(6) INFO FTD_SB_VERSION_DAT R Date of version.c Format of the date should

E be DDMMYY.
c(4) INFO FTD_SB_MCU_CHECKS R MCU SW checksum
UM
d(12) INFO FTD_SB_DSP_VERSION R Version of currently active DSP software
(GSM, TDMA, …)

Display 62.11: Information about HW version (Version: 3.18, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ HW version info +
+ +
+ HW: aaaa +
+ +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Format Mode Description

aaaa INFO FTD_SB_HW_VERSION R Hardware version

Display 62.12: Information about PPM (Version: 3.24, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ PPM info +
+ +
+ PPM aaaaaa +
 SPECIFICATION 217 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ TEXTS bbbbbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(6) INFO FTD_SB_PPM_VERSION S R PPM version (e.g. 2.081B)
b(7) INFO FTD_SB_TEXT_VERSIO S R Language package version
N
 SPECIFICATION 218 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 63: Common OS status displays

Display 63.01: OS Block usage statistics (Blocks 1-8) (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ OS block usage stat 1-8 +
+ R set1/F set1 aa bb +
+ R set2/F set2 cc dd +
+ R set3/F set3 ee ff +
+ R set4/F set4 gg hh +
+ R set5/F set5 ii jj +
+ R set6/F set6 kk ll +
+ R set7/F set7 mm nn +
+ R set8/F set8 oo pp +
+++++++++++++++++++++++++++

1. row: Block set 1, block set 2

2. row: Block set 3, block set 4
3. row: Block set 5, block set 6
4. row: Block set 7, block set 8

Abbr. Server Sub Block ID Form Mode Description

at
aa MON FTD_SB_BLOCK_RES_SET1 B:H R Number of reserved blocks, set 1
bb MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET1 set 1
cc MON FTD_SB_BLOCK_RES_SET2 B:H R Number of reserved blocks, set 2
dd MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET2 set 2
ee MON FTD_SB_BLOCK_RES_SET3 B:H R Number of reserved blocks, set 3
ff MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET3 set 3
gg MON FTD_SB_BLOCK_RES_SET4 B:H R Number of reserved blocks, set 4
hh MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET4 set 4
ii MON FTD_SB_BLOCK_RES_SET5 B:H R Number of reserved blocks, set 5
jj MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET5 set 5
kk MON FTD_SB_BLOCK_RES_SET6 B:H R Number of reserved blocks, set 6
ll MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET6 set 6
mm MON FTD_SB_BLOCK_RES_SET7 B:H R Number of reserved blocks, set 7
nn MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET7 set 7
oo MON FTD_SB_BLOCK_RES_SET8 B:H R Number of reserved blocks, set 8
pp MON FTD_SB_FREE_BL_WORST_C B:H R Number of free blocks in worst case,
ASE_SET8 set 8

Note! The max value of the above fields is FF (255) even thought the OS limits the
maximum number of blocks in the block set to FFFF (65535).. FTD will show FF in case of
the field value exceeds FF.
 SPECIFICATION 219 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 63.02: OS Block usage statistics (Blocks 9-16) (Version: 3.19, Status: Approved)

‘+++++++++++++++++++++++++++
+ OS block usage stat 9-16+
+ R set9/F set9 aa bb +
+ R se10/F se10 cc dd +
+ R se11/F se11 ee ff +
+ R se12/F se12 gg hh +
+ R se13/F se13 ii jj +
+ R se14/F se14 kk ll +
+ R se15/F se15 mm nn +
+ R se16/F se16 oo pp +
+++++++++++++++++++++++++++

1. row: Block set 9, block set 10

2. row: Block set 11, block set 12
3. row: Block set 13, block set 14
4. row: Block set 15, block set 16

Abbr. Server Sub Block ID Form Mode Description

at
aa MON FTD_SB_BLOCK_RES_SET9 B:H R Number of reserved blocks, set 9
bb MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET9 9
cc MON FTD_SB_BLOCK_RES_SET10 B:H R Number of reserved blocks, set 10
dd MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET10 10
ee MON FTD_SB_BLOCK_RES_SET11 B:H R Number of reserved blocks, set 11
ff MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET11 11
gg MON FTD_SB_BLOCK_RES_SET12 B:H R Number of reserved blocks, set 12
hh MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET12 12
ii MON FTD_SB_BLOCK_RES_SET13 B:H R Number of reserved blocks, set 13
jj MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET13 13
kk MON FTD_SB_BLOCK_RES_SET14 B:H R Number of reserved blocks, set 14
ll MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET14 14
mm MON FTD_SB_BLOCK_RES_SET15 B:H R Number of reserved blocks, set 15
nn MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET15 15
oo MON FTD_SB_BLOCK_RES_SET16 B:H R Number of reserved blocks, set 16
pp MON FTD_SB_FREE_BL_WORST_ B:H R Number of free blocks in worst case, set
CASE_SET16 16
 SPECIFICATION 220 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 63.03: OS block allocation errors (Version: 3.32, Status: Approved)

+++++++++++++++++++++++++++
+ OS block alloc errors +
+ Double deallo aaaaaa +
+ Failed deallo bbb +
+ D deallo name cccccccc +
+ Overwrites dd +
+ Out of memory ee +
+ Block pointer fff +
+ Mod blk point gg +
+ Big blk count hh +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(8) MON FTD_SB_POINTER_TO_DEAL DW:H R Pointer to memory where double
LOC deallocation was called, in hex format.
Valid only when double dellocation has
happened.
bbb MON FTD_SB_PPC_DMM_OVER_D W:D R Counter for failed deallocations.
EALLOC
c(12) MON FTD_SB_TASK_NAME_DOUBL S R Name of task that last tried to double
E_DEALLOC deallocate a block. Valid only when
double dellocation has happened.
Note: task names are not available in
some products. In that case task
number is shown, see
os_trace_data.txt
dd MON FTD_SB_DYNMEM_OVERWRI W:D R Counter for overwrites
TE
ee MON FTD_SB_DYNMEM_EXHAUST W:D R Counter for out of memory
ED
fff MON FTD_SB_OS_INTERNAL_ERR W:D R Counter for internal OS errors
OR_COUNT
gg MON FTD_SB_MODIFIED_POINTER W:D R Counter for modified block pointer
hh MON FTD_SB_DYNMEM_BIG_BLOC W:D R Counter for too big block
K

Note: This display is only valid when the counter for failed deallocations is not zero.

Display 63.04: Memory status before reset (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ Memory status +
+ before reset +
+ +
+ Stack status aaaaaaaaa +
+ +
+ +
+ Block status aaaaaaaaa +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 221 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Form Mode Description

. at
a(12) MON FTD_SB_BLOCK_S s R Status of each block set before reset. First
ET_STATUS_1 position contains the status of block set 1,
second position the status of block set 2 and
so on. Possible values for each block set
are:
0 : status OK
1 : block set full
2 : (de)allocation error or total memory
corruption
Note: This display is only valid when a
unknown or a stack overflow interrupt has
occurred.
b(12) MON FTD_SB_BLOCK_S s R See FTD_SB_BLOCK_SET_STATUS_1
ET_STATUS_2 description.

Display 63.05: OS pre-reset error status (Version: 3.32, Status: Approved)

+++++++++++++++++++++++++++
+ OS pre-reset error stat +
+ +
+ Status code st +
+ Os func id fn +
+ Task name aaaaaa +
+ +
+ Task 1 xxxxxxxx +
+ Task 2 yyyyyyyy +
+ Task 3 zzzzzzzz +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
st MON FTD_SB_OS_PRE_R B:H R Status code byte, 00 == no error, other
ESET_ERROR_STAT values in os_trace_data.txt
US (OS_RESPONSES)
fn MON FTD_SB_OS_PRE_R B:D R OS function id where error/warn/remark
ESET_ERROR_FUN occurred, values in os_trace_data.txt
CTION_ID (MONITOR_HOOK_IDS)
a(6) MON FTD_SB_OS_PRE_R S R Task name
ESET_ERROR_TASK Note: task names are not available in some
products. In that case task number is
shown, see os_trace_data.txt
x(8) MON FTD_SB_OS_PRE_R DW:H R Parameter 1, 32-bit hex number. See
ESET_ERROR_PAR dct4_osmo_interpretation.txt
AMETER_1
y(8) MON FTD_SB_OS_PRE_R DW:H R Parameter 2, 32-bit hex number. See
ESET_ERROR_PAR dct4_osmo_interpretation.txt
AMETER_2
z(8) MON FTD_SB_OS_PRE_R DW:H R Parameter 3, 32-bit hex number. See
ESET_ERROR_PAR dct4_osmo_interpretation.txt
AMETER_3
 SPECIFICATION 222 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 63.06: OS current error status (Version: 3.31, Status: Approved)

+++++++++++++++++++++++++++
+ Os current error status +
+ +
+ Status code st +
+ Os func id fn +
+ Task name aaaaaa +
+ +
+ Task 1 xxxxxxxx +
+ Task 2 yyyyyyyy +
+ Task 3 zzzzzzzz +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
st MON FTD_SB_OS_CURREN B:H R Status code byte, 00 == no error, other values
T_ERROR_STATUS in os_trace_data.txt (OS_RESPONSES)
fn MON FTD_SB_OS_CURREN B:D R OS function id where error/warn/remark
T_ERROR_FUNCTION_ occurred, values in os_trace_data.txt
ID (MONITOR_HOOK_IDS)
a(6) MON FTD_SB_OS_CURREN S R Task name
T_ERROR_TASK Note: task names are not available in some
products. In that case task number is shown,
see os_trace_data.txt
x(8) MON FTD_SB_OS_CURREN DW:H R Parameter 1, 32-bit hex number. See
T_ERROR_PARAMETE dct4_osmo_interpretation.txt
R_1
y(8) MON FTD_SB_OS_CURREN DW:H R Parameter 2, 32-bit hex number. See
T_ERROR_PARAMETE dct4_osmo_interpretation.txt
R_2
z(8) MON FTD_SB_OS_CURREN DW:H R Parameter 3, 32-bit hex number. See
T_ERROR_PARAMETE dct4_osmo_interpretation.txt
R_3

Display 63.07: OS pre-reset warning status (Version: 3.31, Status: Approved)

+++++++++++++++++++++++++++
+ Os pre-reset warn status+
+ +
+ Status code st +
+ Os func id fn +
+ Task name aaaaaa +
+ +
+ Task 1 xxxxxxxx +
+ Task 2 yyyyyyyy +
+ Task 3 zzzzzzzz +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
 SPECIFICATION 223 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

st MON FTD_SB_OS_PRE_RES B:H R Status code byte, 00 == no error, other values

ET_WARN_STATUS in os_trace_data.txt (OS_RESPONSES)
fn MON FTD_SB_OS_PRE_RES B:D R OS function id where error/warn/remark
ET_WARN_FUNCTION_ occurred, values in os_trace_data.txt
ID (MONITOR_HOOK_IDS)
a(6) MON FTD_SB_OS_PRE_RES S R Task name
ET_WARN_TASK Note: task names are not available in some
products. In that case task number is shown,
see os_trace_data.txt.
x(8) MON FTD_SB_OS_PRE_RES DW:H R Parameter 1, 32-bit hex number. See
ET_WARN_PARAMETE dct4_osmo_interpretation.txt
R_1
y(8) MON FTD_SB_OS_PRE_RES DW:H R Parameter 2, 32-bit hex number. See
ET_WARN_PARAMETE dct4_osmo_interpretation.txt
R_2
z(8) MON FTD_SB_OS_PRE_RES DW:H R Parameter 3, 32-bit hex number. See
ET_WARN_PARAMETE dct4_osmo_interpretation.txt
R_3

Display 63.08: OS current warning status (Version: 3.31, Status: Approved)

+++++++++++++++++++++++++++
+ Os current warning status +
+ +
+ Status code st +
+ Os func id fn +
+ Task name aaaaaa +
+ +
+ Task 1 xxxxxxxx +
+ Task 2 yyyyyyyy +
+ Task 3 zzzzzzzz +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
st MON FTD_SB_OS_CURRENT_ B:H R Status code byte, 00 == no error, other
WARN_STATUS values in os_trace_data.txt
(OS_RESPONSES)
fn MON FTD_SB_OS_CURRENT_ B:D R OS function id where error/warn/remark
WARN_FUNCTION_ID occurred, values in os_trace_data.txt
(MONITOR_HOOK_IDS)
a(6) MON FTD_SB_OS_CURRENT_ S R Task name
WARN_TASK Note: task names are not available in some
products. In that case task number is
shown, see os_trace_data.txt
x(8) MON FTD_SB_OS_CURRENT_ DW:H R Parameter 1, 32-bit hex number. See
WARN_PARAMETER_1 dct4_osmo_interpretation.txt
y(8) MON FTD_SB_OS_CURRENT_ DW:H R Parameter 2, 32-bit hex number. See
WARN_PARAMETER_2 dct4_osmo_interpretation.txt
z(8) MON FTD_SB_OS_CURRENT_ DW:H R Parameter 3, 32-bit hex number. See
WARN_PARAMETER_3 dct4_osmo_interpretation.txt
 SPECIFICATION 224 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 63.09: OS pre-reset remark status (Version: 3.31, Status: Approved)

+++++++++++++++++++++++++++
+ Os pre-reset remark status +
+ +
+ Status code st +
+ Os func id fn +
+ Task name aaaaaa +
+ +
+ Task 1 xxxxxxxx +
+ Task 2 yyyyyyyy +
+ Task 3 zzzzzzzz +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
st MON FTD_SB_OS_PRE_RESET_R B:H R Status code byte, 00 == no error, other
EM_STATUS values in os_trace_data.txt
(OS_RESPONSES)
fn MON FTD_SB_OS_PRE_RESET_R B:D R OS function id where
EM_FUNCTION_ID error/warn/remark occurred, values in
os_trace_data.txt
(MONITOR_HOOK_IDS)
a(6) MON FTD_SB_OS_PRE_RESET_R S R Task name
EM_TASK Note: task names are not available in
some products. In that case task
number is shown, see
os_trace_data.txt
x(8) MON FTD_SB_OS_PRE_RESET_R DW:H R Parameter 1, 32-bit hex number. See
EM_PARAMETER_1 dct4_osmo_interpretation.txt
y(8) MON FTD_SB_OS_PRE_RESET_R DW:H R Parameter 2, 32-bit hex number. See
EM_PARAMETER_2 dct4_osmo_interpretation.txt
z(8) MON FTD_SB_OS_PRE_RESET_R DW:H R Parameter 3, 32-bit hex number. See
EM_PARAMETER_3 dct4_osmo_interpretation.txt

Display 63.10: OS current remark status (Version: 3.31, Status: Approved)

+++++++++++++++++++++++++++
+ Os current remark status +
+ +
+ Status code st +
+ Os func id fn +
+ Task name aaaaaa +
+ +
+ Task 1 xxxxxxxx +
+ Task 2 yyyyyyyy +
+ Task 3 zzzzzzzz +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
st MON FTD_SB_OS_CURRE B:H R Status code byte,
 SPECIFICATION 225 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

NT_REM_STATUS 00 == no error,
other values in os_trace_data.txt
(OS_RESPONSES)
fn MON FTD_SB_OS_CURRE B:D R OS function id where error/warn/remark
NT_REM_FUNCTION occurred, values in os_trace_data.txt
_ID (MONITOR_HOOK_IDS)
a(6) MON FTD_SB_OS_CURRE S R Task name
NT_REM_TASK Note: task names are not available in some
products. In that case task number is shown,
see os_trace_data.txt
x(8) MON FTD_SB_OS_CURRE DW:H R Parameter 1, 32-bit hex number. See
NT_REM_PARAMET dct4_osmo_interpretation.txt
ER_1
y(8) MON FTD_SB_OS_CURRE DW:H R Parameter 2, 32-bit hex number. See
NT_REM_PARAMET dct4_osmo_interpretation.txt
ER_2
z(8) MON FTD_SB_OS_CURRE DW:H R Parameter 3, 32-bit hex number. See
NT_REM_PARAMET dct4_osmo_interpretation.txt
ER_3

Display 63.11: Heap system status (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ Heap system status +
+ Used bytes (a7) +
+ Used blocks b(4) +
+ Free bytes c(7) +
+ Free blocks d(4) +
+ Zero alloc e(2) +
+ Double alloc f(2) +
+ Invalid point g(2) +
+ Co blk/Chk fa h(2) i(2)+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(7) MON FTD_SB_HEAP_USED_BYTES DW:D R Used bytes
b(4) MON FTD_SB_HEAP_USED_BLOCKS W:D R Used block count
c(7) MON FTD_SB_HEAP_FREE_BYTES DW:D R Free bytes
d(4) MON FTD_SB_HEAP_FREE_BLOCKS W:D R Free block count
ee MON FTD_SB_HEAP_ZERO_ALLOCATE B:D R Count of zero allocations
S
ff MON FTD_SB_HEAP_DOUBLE_DEALLO B:D R Count of double deallocations
C
gg MON FTD_SB_HEAP_INVALID_POINTE B:D R Count of invalid pointers
R
hh MON FTD_SB_HEAP_CORRUPT_BLOC B:D R Count of corrupt blocks
K
ii MON FTD_SB_HEAP_PNTRCHK_FAIL DW : R Total count of pointer check
D failures
 SPECIFICATION 226 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 63.12: Heap top users (Version: 3.31, Status: Approved)

+++++++++++++++++++++++++++
+ Heap top users +
+ Task name a(7) +
+ Blocks used b(4) +
+ Task name c(7) +
+ Blocks used d(4) +
+ Task name e(7) +
+ Blocks used f(4) +
+ Task name g(7) +
+ Blocks used h(4) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(7) MON FTD_SB_HEAP_MEM_OWNER_TA S R Task name
SK_1
b(4) MON FTD_SB_HEAP_MEM_OWNER_BL B:D R Number of blocks used
OCKS_1
c(7) MON FTD_SB_HEAP_MEM_OWNER_TA S R Task name
SK_2
d(4) MON FTD_SB_HEAP_MEM_OWNER_BL B:D R Number of blocks used
OCKS_2
e(7) MON FTD_SB_HEAP_MEM_OWNER_TA S R Task name
SK_3
f(4) MON FTD_SB_HEAP_MEM_OWNER_BL B:D R Number of blocks used
OCKS_3
g(7) MON FTD_SB_HEAP_MEM_OWNER_TA S R Task name
SK_4
h(4) MON FTD_SB_HEAP_MEM_OWNER_BL B:D R Number of blocks used
OCKS_4
Note: task names are not available in some products. In that case task number is shown,
see os_trace_data.txt.

Display 63.13: Failed assertions (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ Failed assertions +
+ +
+ Filename aaaaaaaaaaa+
+ +
+ Line bbbbb +
+ +
+ Counter for +
+ failed asser ccccc +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 227 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Forma Mode Description

. t
a(12) MON FTD_SB_ASSERT_LATEST_F S R Filename, where assertion happened
ILE
b(5) MON FTD_SB_ASSERT_LATEST_L DW:D R Line, where assertion happened
INE
c(5) MON FTD_SB_ASSERT_TOTAL_C W:D R Counter for failed assertions
OUNT

Display 63.14-63.29: Reserved for future use (Version: 1, Status: - )

These displays are reserved for future OS displays.

Display 63.30: Information of OS_SYSTEM_STACK (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ OS_SYSTEM_STACK +
+ +
+ FIQ stack aaaa +
+ +
+ IRQ stack bbbb +
+ +
+ FIQ reset e +
+ +
+ IRQ reset f +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa MON FTD_SB_STACK_STATUS DW:D R FIQ stack status
_ SYSTEM_1 (OS_SYSTEM_STACK_1)
bbbb MON FTD_SB_STACK_STATUS DW:D R IRQ stack status
_ SYSTEM_2 (OS_SYSTEM_STACK_2)
e MON FTD_SB_STACK_PRE_ B:D R Shows the status of FIQ stack just before
RESET_STATUS_SYSTEM reset.
_1 0 : status OK, no overflow
1 : status not OK, stack overflow
f MON FTD_SB_STACK_PRE_ B:D R Shows the status of IRQ stack just before
RESET_STATUS_SYSTEM reset:
_2 0 : status OK, no overflow
1 : status not OK, stack overflow

Note! Values are not stored to permanent memory.

Display 63.31: Select task set (Version: 3.19, Status: Approved)

This displays toggles task set that is shown in displays 63.32 – 63.99. To toggle the set:
1. Press menu-button.
2. Scroll in the main menu to loop to field test display item.
 SPECIFICATION 228 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

3. Press Select-button
4. Select this display in executive mode by entering 6331 at the query prompt.
5. Confirm with the Ok button.
6. Task set is toggled and the resulting set is shown in the display

Note 1: If the display is selected using arrow buttons, then the task set selection is not toggled.
Note 2: This display may have been configured off in products that have less than 69 tasks.

***************************
* Execute display *
* This displays toggles task *
* set that is shown in displays *
* 63.32 – 63.99. Use options to *
* change. *
* *
* *
* Current task a *
* *
***************************

Abbr. Server Sub Block ID Form Mode Description

at
EXE MON FTD_SB_TASK_SET_TOG N/A R Toggle OS task set.
GLE
a MON FTD_SB_TASK_SET_STAT B:D R Current task set selection for displays
US 63.32 – 63.99
1 = tasks 0 – 67
2 = tasks 68 - 135

Displays 63.32 – 63.99: Information about tasks (Version: 3.31, Status: Approved)

These displays show information either about tasks 0 … 67 or tasks 68 – 136 depending on
which task set is currently selected, see display 63.31.

+++++++++++++++++++++++++++
+ Task information +
+ +
+ Task name a(12) +
+ Stack worst b(5) +
+ W mailbox c(5) +
+ F mailbox d(5) +
+ stack overflow e +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
a(12) MON FTD_SB_TASKNAME_X S R Task Name (ASCII)
 SPECIFICATION 229 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Note: task names are not available

in some products. In that case task
number is shown, see
os_trace_data.txt
b(5) MON FTD_SB_STACK_STATUS DW:D R Number tells how many stack
_TASK_X memory locations have been empty
in the worst case. So, if number is
zero, stack has been full. Values
are not stored to permanent
memory.
c(5) MON FTD_SB_MSGBUF B:D R Worst case Mailbox status of task x
_STATUS_TASK_X (x is the task id) i.e. how much
there is queue "places" used in
worst case.
d(5) MON FTD_SB_FASTBUF_STAT B:D R Fast mailbox status of task x (x is
US_TASK_X the task id) i.e. how much there is
queue "places" used in worst case.
e MON FTD_SB_STACK_PRE_RE B:D R Tells whether stack overflow
SET_STATUS_X occurred before reset was done. (x
is the task id)
0 : status OK, no overflow
1 : status not OK, stack overflow

where x = 0 … 67 and corresponds either to task x or task x + 68 depending on selected

task set.
 SPECIFICATION 230 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 64: Common Audio displays

Display 64.01: Read DSP Memory (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Read DSP memory +
+ +
+ DSP fields aaaaa bbbb +
+ +
+ DSP 1-7 cccc dddd +
+ eeee ffff +
+ gggg hhhh +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
INPUT DSP_AUDIO FTD_SB_READ_DSP_A DW:H R Address field for reading DSP
DDR memory. Hex format, 24 Bits.
a(6) DSP_AUDIO FTD_SB_READ_DSP_A DW:H R Address field for reading DSP
DDR_1 memory. Hex format, 24 bits.
b(4) DSP_AUDIO FTD_SB_READ_DSP_M W:H R Current contents of address a(6) in
EM_1 DSP memory
c(4) DSP_AUDIO FTD_SB_READ_DSP_ W:H R Current contents of address a(6) + 1
MEM_2 in DSP memory
d(4) DSP_AUDIO FTD_SB_READ_DSP_ W:H R Current contents of address a(6) + 2
MEM_3 in DSP memory
e(4) DSP_AUDIO FTD_SB_READ_DSP_ W:H R Current contents of address a(6) + 3
MEM_4 in DSP memory
f(4) DSP_AUDIO FTD_SB_READ_DSP_ W:H R Current contents of address a(6) + 4
MEM_5 in DSP memory
g(4) DSP_AUDIO FTD_SB_READ_DSP_ W:H R Current contents of address a(6) + 5
MEM_6 in DSP memory
h(4) DSP_AUDIO FTD_SB_READ_DSP_ W:H R Current contents of address a(6) + 6
MEM_7 in DSP memory
When display is selected, address fields can be edited. Keyboard is in "text"-mode, so hex numbers 0-F
can be written. Data display shows the addresses and their contents. After editing of addresses is
completed, request for reading specified memory locations is sent. These values are updated 5-10
times/second.
 SPECIFICATION 231 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 64.02: Signal generators (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Signal generators +
+ +
+ Signal level: -aa.adB +
+ Frequency: bbbb +
+ Routing: cc +
+ Wave form: dd +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
INPU DSP_AUDI FTD_SB_BASIC_SIGGEN_INPUT DW:D R Test input value (for frequence)
T O
aa.a DSP_AUDI FTD_SB_BASIC_SIGGEN_LEVEL S R Level of the test signal, dB from
O maximum. Decimal format.
bbbb DSP_AUDI FTD_SB_BASIC_SIGGEN_FREQ W:D R Frequency of the test signal.
O Decimal format.
cc DSP_AUDI FTD_SB_BASIC_SIGGEN_ROUT B:D R Routing of the test signal.
O E
dd DSP_AUDI FTD_SB_BASIC_SIGGEN_WAVE B:D R Wave form of the test signal.
O _FORM

This display can be used to control test signal generators in the DSP. When display is selected, fields
can be edited. When editing is completed, a request to start the generators is sent. Because FTD-
application is uncapable to handle more than one iput value per FTD, only frequency input is used at
the beginning.

Display 64.03: Accesory mode status (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Accessory mode status +
+ +
+ Mode: aaa +
+ Accessory mode: bbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 232 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
aaa audio COMM_FTD_DATA_A B:D R Mode: ANA – Analog / DIG - Digital
UD_ANADIGI_MODE
bbb audio COMM_FTD_DATA_A B:D R Accessory mode: HP / HF / HDC5 / HDC9 /
UD_ACCESSORY_MO LPS1 / LPS3 / PPHF / PPHF_EXT / HFU_2 /
DE HFU_2_EXT / ANCO_HP / ANCO_ANC / IHF /
SMART

Display 64.04: Downlink audio display (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Downlink audio +
+ +
+ UEM attenuator aa +
+ Peak value bbbb +
+ Cut off counter cccc +
+ Voice level dddd +
+ Data lack eeee +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa DSP_AUDIO FTD_SB_DNLINK_AUD_ATT B:H R Downlink attenuator setting in
UEM.
bbbb DSP_AUDIO FTD_SB_DNLINK_AUD_SIGNA W:H R Peak value of the downlink
L_PEAK signal since last request.
Counter is reset after every
request.
cccc DSP_AUDIO FTD_SB_DNLINK_AUD_CUT_O W:H R Value of the downlink cut off
FF counter since last request.
Counter is reset after every
request.
dddd DSP_AUDIO FTD_SB_DNLINK_VOICE_LEVE W:H R Dowlink voice level moving
L average in hex
eeee DSP_AUDIO FTD_SB_DNLINK_DATA_LACK W:H R Counter for lack of downlink
data

These values are updated 5-10 times/second.

 SPECIFICATION 233 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 64.05: Uplink audio display (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Uplink audio display +
+ +
+ UEM gain aa +
+ Peak value bbbb +
+ Cut off count cccc +
+ Voice level dddd +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
aa DSP_AUDIO FTD_SB_UPLINK_AUD_GAIN B:H R Uplink gain setting in UEM.
bbbb DSP_AUDIO FTD_SB_UPLINK_AUD_SIGNAL W:H R Peak value of the uplink signal
_PEAK since last request. Counter is
reset after every request.
cccc DSP_AUDIO FTD_SB_UPLINK_AUD_CUT_OF W:H R Value of the uplink cut off
F counter since last request.
Counter is reset after every
request.
dddd DSP_AUDIO FTD_SB_UPLINK_VOICE_LEVEL W:H R Uplink voice level instantaneous
or moving average in hex

These values are updated 5-10 times/second.

Display 64.06: Microphone Active Gain Control (AGC) (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Microphone AGC +
+ +
+ Gain analog aaa +
+ Gain digital bbb +
+ Treshold low ccc +
+ Treshold up ddd +
+ Analog counter eeee +
 SPECIFICATION 234 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaa AUDIO COMM_FTD_DATA_ W:D R Analog microphone gain in dB. Decimal point
AUD_AIN_GAIN and sign is not shown. E.g. –10.5dB is shown
as "105".
20*log10(Q11).
bbb DSP_AU FTD_SB_AGC_DGAI W:D R Digital compensation gain in dB. Decimal point
DIO N is not shown.
20*log10(Q11).
ccc DSP_AU FTD_SB_AGC_ W:D R Lower threshold for Microphone AGC in dB.
DIO LOWER_TRESHOLD Decimal point and sign is not shown. E.g. –
10.5dB is shown as "105". 20*log10(Q11).
ddd DSP_AU FTD_SB_AGC_ W:D R Upper threshold for Microphone AGC in dB.
DIO UPPER_TRESHOLD Decimal point and sign is not shown.
20*log10(Q11).
eeee DSP_AU FTD_SB_AGC_ W:H R Counter for analog gain control. Hex format
DIO GAIN_CONTROL_CO (Q11)
UNTER

Display 64.07: Acoustic Echo Canceller (AEC) (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Acoustic echo canceller +
+ +
+ EAA/Ada/ERL aaa bbb ccc +
+ RxG/TcG/GLi ddd eee fff +
+ TxN/Sta/CNo ggg h iii +
+ RX VAD kkkk +
+ TX VAD llll +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaa DSP_AU FTD_SB _AEC_ W:D R Electro acoustic attenuation of echo in dB.
DIO ACOUSTIC_ATT Decimal point and sign is not shown. E.g. –
10.5dB is shown as "105".
20*log10(Q11).
bbb DSP_AU FTD_SB _AEC_ W:D R Adaptive attenuation of echo in dB. Decimal
DIO ADAPTIVE_ATT point is not shown.
20*log10(Q11).
ccc DSP_AU FTD_SB _AEC_ W:D R Total echo return loss in dB. Decimal point is
DIO ECHO not shown.
 SPECIFICATION 235 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

20*log10(Q11).
ddd DSP_AU FTD_SB _AEC_ W:D R RX attenuation gain in dB. Decimal point and
DIO RX_ATT sign is not shown.
20*log10(Q11).
eee DSP_AU FTD_SB _AEC_ W:D R TX attenuation gain in dB. Decimal point and
DIO TX_ATT sign is not shown.
20*log10(Q11).
fff DSP_AU FTD_SB _AEC_ W:D R Gain limit for RX and TX attenuators in dB.
DIO ATT_GAIN_LIMIT Decimal point and sign is not shown.
20*log10(Q11).
ggg DSP_AU FTD_SB _AEC_ W :D R TX Noise level in dB. Decimal point and sign is
DIO TX_NOISE not shown. 20*log10(Q11).
h DSP_AU FTD_SB _AEC_ B:D R Adaptive filter status.
DIO ADAPTIVE_FILTERS
iii DSP_AU FTD_SB _AEC_ W:H R Comfort noise generation in different 12 sub
DIO COMFORT_NOISE bands. Hex format, 12 bits.
kkkk DSP_AU FTD_SB _AEC_ W:H R 16 last RX VAD decisions in hex format.
DIO RX_VAD
lllll DSP_AU FTD_SB _AEC_ W:H R 16 last TX VAD decisions in hex format.
DIO TX_VAD

These values are updated 5-10 times/second.

Display 64.08: Dynamic/Multi-Band Range Controller (DRC/MDRC) (Version: 3.13, Status:

Approved)

Data Display:

+++++++++++++++++++++++++++
+ DRC/MDRC +
+ +
+ DsL aaa bbb ccc +
+ ddd eee fff +
+ Uspl/UsL ggg hhh +
+ NsL iii +
+ Dtb/Utb jjj kkk +
+ DNTb ll +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
aaa DSP_AUDIO FTD_SB_DRC_DL_SIGNAL_L W:D R Downlink signal level in dB.
bbb EVEL 10*log10(Q11). Decimal point
ccc and sign is not shown. E.g. –
ddd 10.5dB is shown as "105".
eee
fff
ggg DSP_AUDIO FTD_SB_DRC_UL_SPEECH_ W:D R Uplink speech level in dB.
LEVEL 10*log10(Q11). Decimal point
and sign is not shown. E.g. –
10.5dB is shown as "105".
hhh DSP_AUDIO FTD_SB_DRC_UL_SIGNAL_L W:D R Uplink signal level in dB.
 SPECIFICATION 236 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

EVEL 10*log10(Q11). Decimal point

and sign is not shown. E.g. –
10.5dB is shown as "105".
iii DSP_AUDIO FTD_SB_DRC_NOISE_LEVE W:D R Backround noise signal level in
L dB.
10*log10(Q11). Decimal point
and sign is not shown. E.g. –
10.5dB is shown as "105".
jjj DSP_AUDIO FTD_SB_DRC_DL_TBL W:D R Current downlink DRC table(s).
kkk DSP_AUDIO FTD_SB_DRC_UL_TBL W:D R Current uplink DRC table(s).
ll DSP_AUDIO FTD_SB_DRC_DL_NOISE_T B:D R Current downlink noise
BL dependent table.

These values are updated 5-10 times/second.

Display 64.09: Control DSP audio enhancements switch 1 (Version: 3.15, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ DSP audio enhancement 1 +
+ +
+ Entered: aaaa +
+ Switch 1: bbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
INPU DSP_AUDIO FTD_SB_BASIC_ALG_1_VALUE_T DW:H R Value to be written to switch1
T O_SWITCH_1
aaaa DSP_AUDIO FTD_SB_BASIC_ALG_1_VALUE_ W:H R Value written to switch1.
OF_SWITCH_ 1
bbbb DSP_AUDIO FTD_SB_BASIC_ALG_1_CURR_V W:H R Current value of switch1.
ALUE_SWITCH_ 1 Updated 5-10 times per
second.

This can be provided by Audio Server, but currently is not supported

To control DSP audio enhancements, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 6409 (TEST GROUP;TEST DISPLAY) at the query
prompt.
5. Test input display will activate, enter the control words in display. Keyboard is in "text" mode, so
that hex numbers 0-F can be written.
 SPECIFICATION 237 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

6. Confirm with the Ok button.

7. If activation succeeded, the control word is then sent to the DSP.
8. Status of the registers is read 5-10 times per second and filelds a and b are updated accordingly.
This allows the user to see the current values in these registers.

Used together withdisplays 64.10 and 64.11, this display makes rapid on/off switching of audio DSP
algorithms possible. Switching with arrow keys is possible only after this display or display 2 has been
selected from the menu. This prevents accidental on/off switching of algorithms when browsing
displays by arrow keys. Entered values are not saved to permanent memory.

Display 64.10: Control DSP audio enhancements switch 2 (Version: 3.15, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ DSP audio enhancement 2 +
+ +
+ Entered: aaaa +
+ Switch 2: bbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
INPU DSP_AUDIO FTD_SB_BASIC_ALG_1_VALUE_T DW:H R Value to be written to switch2
T O_SWITCH_2
aaaa DSP_AUDIO FTD_SB_BASIC_ALG_1_VALUE_ W:H R Value written to switch2.
OF_SWITCH_ 2
bbbb DSP_AUDIO FTD_SB_BASIC_ALG_1_CURR_V W:H R Current value of switch2.
ALUE_SWITCH_ 2 Updated 5-10 times per
second.

This can be provided by Audio Server, but currently is not supported

To control DSP audio enhancements, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 6410 (TEST GROUP;TEST DISPLAY) at the query
prompt.
5. Test input display will activate, enter the control words in display. Keyboard is in "text" mode, so
that hex numbers 0-F can be written.
6. Confirm with the Ok button.
7. If activation succeeded, the control word is then sent to the DSP.
 SPECIFICATION 238 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

8. Status of the registers is read 5-10 times per second and filelds a and b are updated accordingly.
This allows the user to see the current values in these registers.

Display 64.11: Control DSP audio enhancements switch 3 (Version: 3.15, Status:Approved)

Data Display:

+++++++++++++++++++++++++++
+ DSP audio enhancement 3 +
+ +
+ Entered: aaaa +
+ Switch 3: bbbb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
INPU DSP_AUDIO FTD_SB_BASIC_ALG_1_VALUE_T DW:H R Value to be written to switch3
T O_SWITCH_3
aaaa DSP_AUDIO FTD_SB_BASIC_ALG_1_VALUE_ W:H R Value written to switch3.
OF_SWITCH_ 3
bbbb DSP_AUDIO FTD_SB_BASIC_ALG_1_CURR_V W:H R Current value of switch3.
ALUE_SWITCH_ 3 Updated 5-10 times per
second.

This can be provided by Audio Server, but currently is not supported

To control DSP audio enhancements, perform following steps:

1. Press the Menu button.
2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 6411 (TEST GROUP;TEST DISPLAY) at the query
prompt.
5. Test input display will activate, enter the control words in display. Keyboard is in "text" mode, so
that hex numbers 0-F can be written.
6. Confirm with the Ok button.
 SPECIFICATION 239 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

7. If activation succeeded, the control word is then sent to the DSP.

8. Status of the registers is read 5-10 times per second and filelds a and b are updated accordingly.
This allows the user to see the current values in these registers.

Display 64.12: SpCs (Version: 3.13, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ SpCs +
+ +
+ Rx type aaaa +
+ Tx type bbbb +
+ decode mode cc +
+ encode mode dd +
+ spC type eeeee +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Format Mod Description

e
a(4) DSP_AUDIO FTD_SB_RX_TYPE W:H R Uplink flags (Speech/Background
noise)
b(4) DSP_AUDIO FTD_SB_TX_TYPE W:H R Downlink flags ( BFI, SID, TAF)
c(2) DSP_AUDIO FTD_SB_AMR_DEC_B B:H R AMR SpC Decoder bitrate (00-07)
ITRATE
d(2) DSP_AUDIO FTD_SB_AMR_ENC_B B:H R AMR SpC Encoder bitrate (00-07)
ITRATE
e(5) DSP_AUDIO FTD_SB_SpC_TYPE S R SpC type in string (G_FR, G_EFR,
G_AMR, WAMR1, or WAMR2)

These values are updated 5-10 times/second.

Display 64.13: SpC counters (Version: 3.16, Status: Approved)

Data Display:
 SPECIFICATION 240 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+++++++++++++++++++++++++++
+ SpC counters +
+ +
+ C_handovers aaaaa +
+ C_mode changes bbbbb +
+ C_format changes ccccc +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mod Description

t e
a(5) DSP_AUDIO FTD_SB_C_HAND W:D R Number of codec handovers
OVERS
b(5) DSP_AUDIO FTD_SB_C_MODE W :D R Number of codec mode changes
_CHANGES
c(5) DSP_AUDIO FTD_SB_C_FORM W :D R Number of codec format changes
AT_CHANGES

These values are updated 5-10 times/second.

 SPECIFICATION 241 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 65: Common PPC (Product Performance Counters) displays

Display 65.01: PPC Counters 1 (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ PPC counters 1 +
+ +
+ Ccall timer aaaa +
+ Dmem manag bb +
+ DSP res count cc +
+ SW cr count dd +
+ ASIC wdog res ee +
+ Bad Pof count ff +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa MON FTD_SB_PPC_CUMU DW:D R PPC number 36 : Cumulative Call Timer.
L_CALL_TIMER
bb MON FTD_SB_PPC_DMM_ W:D R PPC number 12 : Dynamic Memory
NO_BUF Management - No Buffers.
cc MON FTD_SB_PPC_DSP_R W:D R PPC number 16 : DSP reset counter.
ESET
dd MON FTD_SB_PPC_SW_C B:D R PPC number 17 : SW crash counter.
RASH
ee MON FTD_SB_PPC_ASIC_ B:D R PPC number 18 : ASIC watchdog reset counter.
WD_RESET
ff MON FTD_SB_BAD_POWE W:D R PPC number 49 : Bad Power Off Counter.
R_OFF

Display 65.02: PPC Counters 2 (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ PPC counters 2 +
+ PA temp aa +
+ PA batt bb +
+ Batt temp cc +
+ Chr full dd +
+ Inv chr conn eeee +
+ Inv C/ Inv B ff gg +
+ I Btemp/Bsize hh ii +
+ Ccon / Cdis kk ll +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa MON FTD_SB_PPC_PA_OV B:D R PPC number 20 : PA Over Temperature Power
ER_T_PWR_OFF off counter.
bb MON FTD_SB_PPC_PA_OV B:D R PPC number 21 : PA Over Temperature Power
ER_T_BATT_TEMP off Battery temperature.
 SPECIFICATION 242 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

cc MON FTD_SB_PPC_BATT_ B:D R PPC number 22 : Battery Over Temperature

OVER_T_PWR_OFF Power off counter.
dd MON FTD_SB_PPC_BATT_ B:D R PPC number 23 : Battery Over Temperature
OVER_T_PA_TEMP Power off PA temperature
Eeee MON FTD_SB_PPC_BATT_ DW:D R PPC number 24 : Battery Charged to Full
CHARGED_FULL Counter.
ff MON FTD_SB_PPC_INV_C B:D R PPC number 27 : Invalid Charger Connected
HA_CONN counter.
gg MON FTD_SB_PPC_INV_B B:D R PPC number 29 : Invalid Battery Connection
ATT_CONN counter.
hh MON FTD_SB_PPC_INV_B W:D R PPC number 30 : Invalid Battery Connection
ATT_CONN_BTEMP BTEMP.
ii MON FTD_SB_PPC_INV_B W:D R PPC number 31 : Invalid Battery Connection
ATT_CONN_BSIZE BSIZE.
jjjj MON FTD_SB_PPC_CHA_C W:D R PPC number 32 : Charger connection counter.
ONN
kkkk MON FTD_SB_PPC_CHA_D W:D R PPC number 33 : Charger disconnection
ISCONN counter.

Display 65.03: PPC Counters 3 (Version: 3.19, Status: Approved)

+++++++++++++++++++++++++++
+ PPC counters 3 +
+ +
+ Dropped calls aaaa +
+ +
+ Dropped calls +
+ rssi -bbb +
+ +
+ Dropped call +
+ BER % cccc +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa MON FTD_SB_PPC_DROPPED DW:D R PPC number 40 : Total number of dropped
_CALL calls.
-bbb MON FTD_SB_PPC_DROPPED B:D R PPC number 41 : Dropped call rssi (in dBm).
_CALL_RSSI
cccc MON FTD_SB_PPC_DROPPED B:D R PPC number 43 : Dropped call ber(in %).
_CALL_BER

Display 65.04: Camera PPCs (Version: 3.27, Status: Approved)

+++++++++++++++++++++++++++
 SPECIFICATION 243 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

+ Camera PPC counter +

+ +
+ App started a(7) +
+ Cont int fail b(4) +
+ Viewfinder run c(7) +
+ Data int fail d(4) +
+ Pic landscape e(4) +
+ Pic portrait f(4) +
+ Discar images g(4) +
+ CCP / twilight h(2) I(4)+
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(7) MON FTD_SB_PPC_CAMERA_APP_STA DW:D R Camera application started
RT
b(4) MON FTD_SB_PPC_CAMERA_CONTROL W:D R Camera control interface failed
_FAILED
c(7) MON FTD_SB_PPC_CAMERA_VIEW_RU DW:D R Camera viewfinder runtime
NTIME counter
d(4) MON FTD_SB_PPC_CAMERA_DATA_FAI W:D R Camera data interface failed
LED
e(4) MON FTD_SB_PPC_PICTURE_LANDSCA W:D R Pictures taken landscape
PE
f(4) MON FTD_SB_PPC_PICTURE_PORTRAI W:D R Pictures taken portrait
T
g(4) MON FTD_SB_PPC_PICTURE_DISCARD W:D R Discarded images
ED
h(2) MON FTD_SB_PPC_COMPACT_CAMERA B:D R CCP stuck counter
_PORT_STUCK
I(4) MON FTD_SB_PPC_PICTURE_TWILIGHT W:D R Pictures taken twilight

Display 65.05: HW UI counters (Version: 3.28, Status: Approved)

+++++++++++++++++++++++++++
+ HW UI counter +
+ +
+ Flip open a(8) +
+ +
+ +
+ EL on time b(8) +
+ +
+ Keypad Chinese character+
+ input counter c(8) +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
FTD_SB_PPC_FLIP_OPEN_
a(8) MON DW:D R PPC 1014: Flip open counter
TIMES
FTD_SB_PPC_EL_ON_TIM PPC 1015: EL on time counter (in
b(8) MON DW:D R
E second)
FTD_SB_PPC_KEYPAD_CH PPC 1016: Keypad Chinese Character
c(8) MON DW:D R
INESE_CHARACTER_INPU Input Counter
 SPECIFICATION 244 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

T
Note: repeated in display 76.06.
 SPECIFICATION 245 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 73: Common Accessory displays

Please refer Accessory Server specific documentation for more information about the data
items.

Display 73.01: Accessory mode information 1 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Accessory mode info 1 +
+ +
+ Accessory mode aa +
+ Accessory detect bb +
+ Last head Int cccc +
+ Last hook int dddd +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Forma Mod Description

. t e
aa Accessor ACC_SB_FTD_ACC_MO R Accessory mode (byte, hex)
y DE
bb Accessor ACC_SB_FTD_ACC_DET R Accessory detection in progress flag: 0 / 1
y _ON (byte, hex)
cccc Accessor ACC_SB_FTD_ACC_HE R Last HeadInt channel reading (word, hex)
y ADINT
dddd Accessor ACC_SB_FTD_ACC_HO R Last HookInt channel reading (word, hex)
y OKINT

Display 73.02: Accessory mode information 2 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Accessory mode info 2 +
+ +
+ Loop counter aa +
+ P&P hf wrong inst bb +
+ P&P hf power down cc +
+ Charger disconnect dd +
+ +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 246 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr Server Sub Block ID Format Mode Description

.
aa Accessor ACC_SB_FTD_ACC_COUNT R Accessory detection loop counter
y ER value (byte, hex)
bb Accessor ACC_SB_FTD_ACC_PPHF_ R Plug and play handsfree wrong
y WI installation flag: 0 / 1 (byte, hex)
cc Accessor ACC_SB_FTD_ACC_PPHF_ R Plug and play handsfree power down
y DOWN flag: 0 / 1 (byte, hex)
dd Accessor ACC_SB_FTD_ACC_CHRG_ R Charger disconnection detected flag:
y DC 0 / 1 (byte, hex)

Display 73.03: Accessory mode information 3 (Version: 1, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Accessory mode info 3 +
+ +
+ Headset btn down aa +
+ HFU car kit state bb +
+ HFU car kit state up cc +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa Accessor ACC_SB_FTD_ACC_ R Headset detected in button down state flag: 0 /
y HD_BTN_DOWN 1 (byte, hex)
bb Accessor ACC_SB_FTD_ACC_ R HFU-2x car kit state indication data (byte, hex)
y HFU2_INFO
cc Accessor ACC_SB_FTD_ACC_ R HFU-2x car kit start up indication data (byte,
y HFU2_SU_INFO hex)

Display 73.04: Vibra information (Version: 1, Status: Approved)

 SPECIFICATION 247 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Data Display:

+++++++++++++++++++++++++++
+ Vibra information +
+ +
+ Vibra state aa +
+ Vibra intensity bb +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aa Accessor ACC_SB_FTD_ACC_ R Vibra state (off/on) flag: 0 / 1 (byte, hex)
y VBR_STATE
bb Accessor ACC_SB_FTD_ACC_ R Vibra intensity (relative clock frequency) data:
y VBR_INT 0x00 - 0x64 (byte, hex)

Display 73.06: Ambient light sensor information 1 (Version: 1, Status: Approved )

Data Display:

+++++++++++++++++++++++++++
+ Ambient light sensor +
+ info 1 +
+ +
+ Luminance level aa +
+ Calibrated value bbbb +
+ Temp comp value cccc +
+ Raw AD value dddd +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mod Description

at e
aa Accessor ACC_SB_FTD_ACC_ALI_LU B:H R Ambient light luminance level (byte,
y M hex)
bbbb Accessor ACC_SB_FTD_ACC_ALI_CA W:H R Ambient light calibrated value (word,
y L_VAL hex)
cccc Accessor ACC_SB_FTD_ACC_ALI_TE W:H R Ambient light temperature
y MP_VAL compensated value (word, hex)
dddd Accessor ACC_SB_FTD_ACC_ALI_RA W:H R Ambient light raw AD value (word,
 SPECIFICATION 248 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

y W_VAL hex)

Display 73.07: Ambient light sensor information 2 (Version: 1, Status: Approved )

Data Display:

+++++++++++++++++++++++++++
+ Ambient light sensor +
+ info 2 +
+ +
+ CalConv cal value aaaa +
+ VCXO temperature bbbb +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Form Mode Description

. at
a(4) ACCESSO ACC_SB_FTD_ACC_ALI_CAL W:H R Ambient light CalConv –
RY CONV calibration value (word, hex)
b(4) ACCESSO ACC_SB_FTD_ACC_ALI_VCX B:D R VCXO Temperature (byte,
RY OTEMP decimal)
 SPECIFICATION 249 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 74: Common Memory Management displays

+++++++++++++++++++++++++++
+ MeM component versions +
+ +
+ PMM release ID +
+ a(11) +
+ PERM release ID +
+ b(11) +
+ NVD release ID +
+ c(11) +
+ +
+++++++++++++++++++++++++++

Display 74.01: Information of MeM component versions (Version: 1, Status: Approved)

Abbr. Server Sub Block ID Forma Mod Description

t e
a(11) PERM PERM_SB_FTD_PMM_VER S R PMM release
SION ID
b(11) PERM PERM_SB_FTD_PERM_VE S R PERM release
RSION ID
c(11) NVD PERM_SB_FTD_NVD_VER S R NVD release
SION ID

Display 74.02: Information of PMM Plain area (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PMM Plain area +
+ Memory used a(7) +
+ % used b(4) +
+ Memory release c(7) +
+ % released d(4) +
+ Memory unused e(7) +
+ % unused f(4) +
+ Number of bloc g(3) +
+ Block size h(7) +
+++++++++++++++++++++++++++

Abbr Server Sub Block ID Form Mode Description

. at
a(7) PERM PERM_SB_FTD_PMM_PLAIN_TOTAL_MEMORY R Memory Used
_USED
b(4) PERM PERM_SB_FTD_PMM_PLAIN_TOTAL_MEMORY B:D R % Used
_USED_PC
c(7) PERM PERM_SB_FTD_PMM_PLAIN_TOTAL_MEMORY R Memory Released
_RELEASED
d(4) PERM PERM_SB_FTD_PMM_PLAIN_TOTAL_MEMORY B:D R % Released
_RELEASED_PC
e(7) PERM PERM_SB_FTD_PMM_PLAIN_TOTAL_MEMORY R Memory Unused
_UNUSED
 SPECIFICATION 250 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

f(4) PERM PERM_SB_FTD_PMM_PLAIN_TOTAL_MEMORY B:D R % Unused

_UNUSED_PC
g(3) PERM PERM_SB_FTD_PMM_PLAIN_TOTAL_PAGE_N W:D R Number of Blocks
UMBER (configuration)
h(7) PERM PERM_SB_FTD_PMM_PLAIN_PAGE_SIZE R Block size
(configuration)

Display 74.03: Information of PMM Classified area (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PMM classified area +
+ Memory used a(7) +
+ % used b(4) +
+ Memory release c(7) +
+ % released d(4) +
+ Memory unused e(7) +
+ % unused f(4) +
+ Number of bloc g(3) +
+ Block size h(7) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaaaaa PERM PERM_SB_FTD_PMM_CLASS_TOT R Memory Used
AL_MEMORY_USED
bbbb PERM PERM_SB_FTD_PMM_CLASS_TOT B:D R % Used
AL_MEMORY_USED_PC
ccccccc PERM PERM_SB_FTD_PMM_CLASS_TOT R Memory Released
AL_MEMORY_RELEASED
dddd PERM PERM_SB_FTD_PMM_CLASS_TOT B:D R % Released
AL_MEMORY_RELEASED_PC
eeeeeee PERM PERM_SB_FTD_PMM_CLASS_TOT R Memory Unused
AL_MEMORY_UNUSED
ffff PERM PERM_SB_FTD_PMM_CLASS_TOT B:D R % Unused
AL_MEMORY_UNUSED_PC
gggg PERM PERM_SB_FTD_PMM_CLASS_TOT R Number of Blocks
AL_PAGE_NUMBER (configuration)
hhhhhhh PERM PERM_SB_FTD_PMM_CLASS_PAG R Block size (configuration)
E_SIZE

Display 74.04: Information of PMM Protected area (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PMM protected area +
+ Memory used a(7) +
+ % used b(4) +
+ Memory release c(7) +
+ % released d(4) +
+ Memory unused e(7) +
+ % unused f(4) +
+ Number of bloc g(3) +
+ Block size h(7) +
+++++++++++++++++++++++++++
 SPECIFICATION 251 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
aaaaaaa PERM PERM_SB_FTD_PMM_PROT_TOTA R Memory Used
L_MEMORY_USED
bbbb PERM PERM_SB_FTD_PMM_PROT_TOTA B:D R % Used
L_MEMORY_USED_PC
ccccccc PERM PERM_SB_FTD_PMM_PROT_TOTA R Memory Released
L_MEMORY_RELEASED
dddd PERM PERM_SB_FTD_PMM_PROT_TOTA B:D R % Released
L_MEMORY_RELEASED_PC
eeeeeee PERM PERM_SB_FTD_PMM_PROT_TOTA R Memory Unused
L_MEMORY_UNUSED
ffff PERM PERM_SB_FTD_PMM_PROT_TOTA B:D R % Unused
L_MEMORY_UNUSED_PC
gggg PERM PERM_SB_FTD_PMM_PROT_TOTA R Number of Blocks
L_PAGE_NUMBER (configuration)
hhhhhhh PERM PERM_SB_FTD_PMM_PROT_PAGE R Block size (configuration)
_SIZE

Display 74.05: PMM Storing information (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PMM protected area +
+ +
+ % Rec. foreg. a(3) +
+ % Rec. backg. b(3) +
+ Fragments c(4) +
+ Pool size d(8) +
+ Mem reserv. e(8) +
+ Swap size f(8) +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaa PERM PERM_SB_FTD_PMM_FOREGRO B:D R % Records written in
UND_WRITE_PC Foreground
bbb PERM PERM_SB_FTD_PMM_BACKGRO B:D R % Records written in
UND_WRITE_PC Background
cccc PERM PERM_SB_FTD_PMM_FRAGMEN R Total amount of fragments
T_COUNTER
dddddddd PERM PERM_SB_FTD_PMM_PLAIN_PO R Remaining Pool size in Plain
OL_SIZE_QUERY area
eeeeeeee PERM PERM_SB_FTD_PMM_PLAIN_ME R Memory reservations in Plain
M_TOTAL_RES_QUERY area
ffffffff PERM PERM_SB_FTD_PMM_PLAIN_SW R Swap size in Plain area
AP_SIZE
 SPECIFICATION 252 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 74.06: PMM Error information 1 (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PMM Error info 1 +
+ +
+ Log adress a(8) +
+ Error code b(8) +
+ Write address c(4) +
+ Read address d(8) +
+ +
+ +
+ +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Forma Mode Description

t
aaaaaaaa PERM PERM_SB_FTD_PMM_ERROR_LOG_PR R Log address
ESENT
bbbbbbbb PERM PERM_SB_FTD_PMM_ERROR_CODE R Error code
cccccccc PERM PERM_SB_FTD_PMM_ERROR_WRITE_ R Write address
ADDRESS
dddddddd PERM PERM_SB_FTD_PMM_ERROR_READ_A R Read address
DDRESS

Display 74.07: PMM Error information 2 (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PMM Error info 2 +
+ +
+ Write error counter +
+ a(8) +
+ Read error counter +
+ b(8) +
+ Calling group ID +
+ c(4) +
+ Calling index number +
+ d(8) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
a(8) PERM PERM_SB_FTD_PMM_DEV_FLASH_WRITE_ER R Write error counter
ROR_COUNTER
b(8) PERM PERM_SB_FTD_PMM_DEV_FLASH_READ_ERR R Read error counter
OR_COUNTER
c(4) PERM PERM_SB_FTD_PMM_CALLING _GROUP R Calling group ID
d(4) PERM PERM_SB_FTD_PMM_CALLING _INDEX R Calling Index
number
 SPECIFICATION 253 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Display 74.08: Information of PMM Clean-up (Version: 1, Status: Approved)

+++++++++++++++++++++++++++
+ PMM clean-up +
+ +
+ Retry peak data read +
+ a(4) +
+ Retry peak data write +
+ b(4) +
+ Retry peak header read +
+ c(3) +
+ Cleanup peak d(3) +
+ Writeback peak e(3) +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa PERM PERM_SB_FTD_PMM_ERROR_RETR R Retry peak on record data read
Y_DATA_READ
bbbb PERM PERM_SB_FTD_PMM_ERROR_RETR R Retry peak on record data write
Y_DATA_WRITE
ccc PERM PERM_SB_FTD_PMM_ERROR_RETR R Retry peak on record header
Y_HEADER_READ read
PERM PERM_SB_FTD_PMM_PEAK_CLEAN R Cleanup peak (in mailbox)
UP_MAILBOX
eee PERM PERM_SB_FTD_PMM_PEAK_WRITEB R Writeback peak (in mailbox)
ACK_MAILBOX

Group 81: Multimode protocol displays

Display 81.01: Force protocol between GSM and WCDMA (Version: 3.26, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Force protocol between +
+ GSM and WCDMA +
+ +
+ 0-dual +
+ 1-GSM +
+ 2-WCDMA +
+ +
+ a +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 254 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

To change Force Protocol status, perform following steps:

1. Press the Menu button.

2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in input mode by entering 8101 (Multimode protocol displays; Force protocol)
to the query prompt.
5. Test input prompt will activate, enter the Force Protocol status code (see the table below) in
display.
6. Confirm with the Ok button.

Abbr. Server Sub Block ID Format Mode Description

INPUT GSS FTD_SB_SELECTED_RAT_SET DW:D R,I,O Force protocol
0 = dual mode
1 = GSM
2 = WCDMA
a GSS FTD_SB_SELECTED_RAT_READ B:D R,I,O Forced protocol:
0 = dual mode
1 = GSM
2 = WCDMA
255 = unknown

Display 81.02: Toggle Integrity Protection Mode (Version: 3.26, Status: Approved)

Data Display:

+++++++++++++++++++++++++++
+ Toggle intergrity +
+ protection mode on/off +
+ +
+ aaa +
+ +
+ +
+ +
+ +
+ +
+++++++++++++++++++++++++++

To change integrity protection mode, perform following steps:

1. Press the Menu button.

2. Scroll in the main menu loop to field test display item.
3. Press the Select button.
4. Select this display in executive mode by entering 8102 (Multimode protocol displays;toggle
integrity protection mode) to the query prompt.
 SPECIFICATION 255 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

5. Confirm with the Ok button.

Abbr. Server Sub Block ID Format Mode Description

EXE GSS FTD_SB_GSS_INT_PRO_MODE_TO N/A R,I,O Toggle integrity
GGLE protection mode.
a(3) GSS FTD_SB_GSS_INT_PRO_MODE S R,I,O Current integrity
protection mode:
ON : Enabled
OFF : Disabled
 SPECIFICATION 256 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Group 99: Charlie specific displays

Display 99.01: PPC Counters

Data Display:

+++++++++++++++++++++++++++
+ PPC Counters +
+ +
+ Reflash aaaa +
+ Ins SIM bbbb +
+ SW reset cccc +
+ +
+ SYMBIAN panic prog dddd +
+ SYMBIAN panic data eeee +
+ SYMBIAN panic reas ffff +
+++++++++++++++++++++++++++

Abbr. Server Sub Block ID Form Mode Description

at
aaaa PPC number 50 : Reflash Counter
bbbb PPC number 94 : Insert SIM Card Error counter

cccc PPC number 327 : SW reset reason

dddd PPC number 331 : SYMBIAN Panic program

counter

eeee PPC number 332 : SYMBIAN Panic data abort

counter
ffff PPC number 333 : SYMBIAN Panic reason
counter

Display 99.04: Einfo on FTD

Data Display:

+++++++++++++++++++++++++++
+ Einfo +
+ +
+ APE SW aaaaaaaa +
+ CellMo SW bbbbbbbb +
+ APE image cccccccc +
+ HWId dddddddd +
+ +
+ +
+ +
+++++++++++++++++++++++++++
 SPECIFICATION 257 (257)

NMP / IBU Design Validation 8.4.2004 V 1.0

Jari.P.Jokinen DTS08337-EN-1.0 Approved

Abbr. Server Sub Block ID Form Mode Description

at
a(8) APE SW (AMCU, ADSP)
b(8) CellMo SW (CMCU, CDSP)
c(8) APE variant image version

d(8) HWIDn versionro

4 REFERENCES
1. Original GSM Field Test Display Specification:
Part: HD9413:SPEC.BASE
Item: HD9413:FIELD_TEST_DISPLAY_SPEC.BASE-SPEC
File: hd94x_field_test_display_spec.txt

2. Original TDMA Field Test Display Specification:

DAMPS_CS_SW: IS136_FT_DISPLAY_SPEC.BASE-SPEC.

3. Field Test Display – Application configuration:

Workset: ISA:WS_ISA
Part: ISA:DOCUMENTS.BASE
Item: ISA:USER_GUIDES.BASE
File: FTD_Appl_conf_guide.doc

4. Product Performance counters specification:

Doc No: DSP00033-EN
Database: WinTesla-Camberley (UK)
Filename: document\wintesla\ppc_spec.doc

5. BT102 locals message description, v10.2 27.9.2001. Proposal. Thomas Busse.

\\trenfs05\Calypso\sw\System\Bluetooth\Documents\Bochum\BT102_loc_spec.doc

6. BT102 – Product performance counter, v8.0 15.8.2001. Approved. Thomas Busse

\\trenfs05\Calypso\sw\System\Bluetooth\Documents\Bochum\BT102_ppc_spec.doc

7. BT102 FTD event message description, v4.0 29.3.2001. Approved. Daniel Bencak, Dietmar Schepp
\\trenfs05\Calypso\sw\System\Bluetooth\Documents\Bochum\BT102_ftd_event_msg.doc