Compound Bow USERS GUIDE

QUALITY SINCE 1878

VERY IMPORTANT: SAVE THIS BOOKLET. CAREFULLY READ ALL INSTRUCTIONS IN THIS MANUAL BEFORE USING YOUR NEW BOW.

Compound Bow USERS GUIDE

WELCOME TO THE BROWNING ARCHERY FAMILY
Thank you from the entire Browning Archery family for purchasing a Browning Archery bow. Your Browning Archery bow was manufactured from the finest materials available and handcrafted with pride in the USA. With proper care and use you will enjoy this product for years to come. We at Browning Archery wish you much success in the archery field you have chosen to pursue. Please read this entire booklet before shooting or adjusting your bow. Remember, most adjustments to a compound bow should be made by your authorized Browning Archery dealer. Whenever shooting a bow, be certain of your target as well as what else lies downrange.

SAFETY
As with any shooting activity, safe operation of your Browning Archery bow must always be the highest priority. ALWAYS WEAR SAFETY GLASSES WHEN HANDLING A BOW. Do not attempt to use your bow without proper instruction. Doing so can result in serious injury.
a. Never "dry-fire" any bow. Dry-fire is to draw and release the bowstring without an arrow in the bow. Dry-firing will likely cause damage to the bow and serious injury to the archer. If you ever dry-fire your Browning Archery bow, take it to an authorized Browning Archery dealer for proper inspection. Always be sure of your intended target, as well as what lies behind the target area. An arrow can travel a considerable distance, so it is important to have a safe and sound backstop. If you draw a bow and need to let it down, do so in a slow and careful manner. Keep your support arm straight and prepare for a rapid and aggressive let-down as the bow returns to peak weight. Avoid hitting your hand on protruding accessories such as the cable guard or quiver. Keep your head and face back and out of the string path during let-down. Never modify any part of the bow or its components by drilling extra holes or removing material. This voids the warranty and presents safety problems. Never draw a bow with a peak weight above your comfort level. Always use a bow sling when drawing and shooting a bow.

b. c.

d. e. f.

CONTACT US
520-838-2004 www.browning-archery.com Browning Archery Warranty Registration P.O. Box 5487 Tucson, Arizona 85703

BROWNING AUTHORIZED SERVICE

Your local authorized Browning Archery dealer is your best source for information and assistance. Visit them for these and other typical services. Adjusting draw length and draw weight Replacing / servicing strings and cables All aspects of bow tuning Correct arrow selection Cleaning and lubrication Mounting new accessories Adjusting tiller

Compound Bow USERS GUIDE

BOW TERMINOLOGY
IDLER WHEEL LIMB

BOW QUIVER

CABLE

SIGHT PEEP SIGHT RISER CABLE GUARD SLIDE

SHELF STABILIZER
ARROW REST

CABLE GUARD STRING LOOP

GRIP

BOW SLING BACKSTOP LIMB BOLT LIMB POCKET STRING

ARROWS

CAM
3

Compound Bow USERS GUIDE

GENERAL OPERATING INSTRUCTIONS
Always inspect your bow thoroughly before each shooting session to ensure that it is in good working order. Check for worn or missing components and have them replaced as required. Inspect your arrows to insure that they are straight, un-damaged, not cracked and that each nock is in good condition. A cracked nock can break when fired from the bow and cause the bow to "dry fire" which can cause injury to the archer and damage to the bow. When purchasing arrows for your bow, consult the selection chart from the arrow manufacturer and select the correct arrow for your application. Always use an arrow that meets the weight requirement stated in the warranty. Failure to do so could cause personal injury and damage to your bow.

BOW MAINTENANCE
Your Browning Archery bow will give you many years of service if maintained and cared for properly. Keep synthetic cables and string waxed. Apply bow string wax to your synthetic cables and string before each shooting session. Strings and cables must be replaced periodically. A worn cable or string can suddenly break, causing serious injury to the archer and damage to the bow. It is recommended that the string and cables be replaced every 5,000 shots or 12 months, whichever comes first. Always store your bow in a cool dry place. High temperatures, such as those that can occur in a trunk or interior of a vehicle, can cause serious damage to your bow. After use in high humidity or damp conditions, wipe metal components of bow with a light oil.

SETTING UP YOUR BOW

Nocking Point Placement:
Release Aid shooters: Install the nocking point so that the arrow passes at the center of the arrowrest mounting hole and runs parallel to the tuning mark on the window of the bow. Finger shooters: Install the nocking point so that the arrow passes at the center of the arrowrest mounting hole and runs slightly point-down relative to the tuning mark on the window of the bow.
Alignment Mark Arrowrest mounting hole

Arrowrest Adjustment:
When shooting with a release aid the in/out position of the arrowrest should be adjusted so that the arrow runs parallel with the tuning mark on the shelf when viewed from above. When shooting with fingers the arrow should point slightly away from the tuning mark on the shelf.
Alignment Mark

Sight Adjustment:
When adjusting the sight pin locations, always remember to "follow the group". That is, if the shot group is to the left of the target, move the sight pins to the left. If the shot group is low, move the sight pins down.
4

Compound Bow USERS GUIDE

CABLE GUARD ADJUSTMENT & INSTALLATION:
Install the cable guard as shown in Figure A. Adjust the cable guard so the cables just clear the arrow vanes. On bows using an offset cable guard rod, adjustments must be done with the rod in the up position (approximately 1 oclock) as shown in Figure B (11 oclock for left handed bows). Excessive arrow clearance may cause the cable to track incorrectly on the wheels and cause personal injury and/or damage to the bow.

Figure A

Figure B

INSTALLATION OF ACCESSORIES
Arrowrest: The arrowrest should be installed according to the instructions
Holes B

received with the product. It is usually mounted to the riser in the threaded hole on the side opposite the shelf (hole "A") using the hardware provided with the arrowrest.

Hole A
Shelf

Sight: The sight should be installed according to the instructions received with the product. It is usually mounted to the riser in the threaded holes (holes "B") on the side opposite the shelf using the hardware provided with the sight. Some bows are equipped with multiple sight mounting holes which allow the sight to be moved up or down. Stabilizer: The stabilizer should be mounted according to the manufacturer's
recommendation. It is usually mounted in the threaded hole on the front of the riser (hole "C").

Hole C

Bow Sling: The bow sling attaches to the riser of the bow generally with the stabilizer. If a stabilizer is not used, attach the sling to the riser with the correct sized bolt using the hole provided for the stabilizer (hole "C").

OTHER ADJUSTMENTS
Draw Weight: Your bow is factory-set to the peak weight indicated on the label on the lower limb of the bow. Slight changes in draw weight can be obtained by turning the limb bolt in or out. Before making any changes in weight, turn the limb bolt clockwise until it no longer moves. This adjusts the limb to its maximum weight setting. Never use extreme torque when turning the bolt or damage to the limb may occur. The limb bolt then may be turned counterclockwise to obtain the desired weight, but NEVER more than 4 turns or revolutions out from the bottomed position. Adjust each limb exactly the same.
5

Compound Bow USERS GUIDE

CAM ORIENTATION
On cams with orientation marks, a reference mark is found to indicate an approximate orientation. This line is for reference only and is meant to give approximate orientation only and may vary between bow models. The orientation of the cams may be changed slightly by twisting or untwisting the string or cable. If attaching the string to the + or the - post, the orientation marks will not be aligned with the cable.

DRAW LENGTH
All adjustable Browning Archery bows feature the patented inner-cam draw length adjustment system. This system allows draw length adjustments over a prescribed range without putting the bow in a bowpress. In all cases, the "A" setting is the longest draw length for that bow and draw lengths get shorter as you progress up the alphabet (A to B, B to C, etc.) When adjusting the inner cam on a twocam bow or hybrid cam bow, both cams must be set in the same letter position. In cases where there is a separate draw stop, the draw Inner Cam stop must be moved to the hole marked with the corresponding letter as the inner cam setting. For minor changes in draw length, the bow must be placed in a suitable bow press and tension relieved from the string and cable. The string side of the cam may have additional posts. Moving the string from the post with the dot to the post with the + will increase draw by approximately . Moving the string from the post with the dot to the post with the - will decrease draw by approximately .

+ post

Factory Setting

- post Draw Stop

Compound Bow USERS GUIDE

STOP ADJUSTMENTS
DRAW STOP:
Draw stop mounting positions are located on both sides of the cam. The position of the draw stop must match the size of the module. For example, if the inner cam is in the B setting, the stop must be in the B position.

80%

LET-OFF:
Let-off adjustment is part of the draw stop. To adjust from high to lower let-off, remove the draw stop from the higher let-off hole and reinstall it in the lower let-off hole of the corresponding inner cam letter. For example, if the cam is set in the B draw length setting, the stop must be reinstalled in the hole marked B in the row marked with the lower let-off setting. Changing to lower let-off will shorten the draw length a small amount.

65%

D setting 80% D setting 65%

DISCOVERY CAM
The Discovery cam design ramps up to the bows peak draw weight and then holds a constant draw weight up to 30 inches.

Compound Bow USERS GUIDE

BACKSTOP INSTRUCTIONS
Note: Some Browning bow models come from the factory with the Backstop installed. These instructions refer to reinstallation or adjustment if needed after making adjustments to your bow. 1. Remove the set screws from the base using a 1/16 hex wrench. 2. Install the Backstop into the threaded hole below the grip on the string- facing side of the bow. 3. Extend the Backstop until it makes contact with the string. Mark the string above and below where it makes contact with the string. Remove the Backstop and add serving to that area of the string. Reinstall the Backstop. 4. To avoid any possibility of the cables striking the setscrews, the setscrews must be facing away from the cables. If they are not, remove the Backstop base, add the washer provided and reinstall the Backstop base as shown. 5. Securely tighten the base to the bow handle. 6. Extend rod from base until rubber stopper contacts the string. Rotate rod until the indentation in the rod closest to the alignment hole (see picture) can be identified. Rod should be rotated 180 and the rod/stopper lightly pushed into the string until the next available indentation is visible (Detent holes are offset see picture below). Install the setscrews to secure rod in this position. Tighten setscrews.

Serve string in this area. Add washer if setscrews are near cables.

Set screws Alignment hole

Compound Bow USERS GUIDE

HYPERLITE POCKET FEATURES
HYPERLITE UNIBODY POCKET NOTICE
The Hyperlite Pocket System is unlike that on any other bow. Some special considerations must be followed so that the system continues to function properly. (this excludes the Micro Adrenaline which bottoms on the riser)

IMPORTANT: DO NOT BOTTOM THE LIMBS AGAINST THE RISER ON A BOW EQUIPPED WITH THE HYPERLITETM UNIBODY POCKET SYSTEM!
Traditional limb pockets use a bottomed position to determine peak weight. This position is where the limb, pocket and riser contact one another simultaneously. Due to the unique design of the HyperLiteTM Unibody Pocket System, the bottomed limb position does not exist. The bottomed position for HyperLiteTM Unibody pockets is where the bottom surface of the limb is approximately .20 (3/16 or 5 mm) away from the riser (Figure 1). The limb bolt may be adjusted to slightly increase the draw weight, but the gap between the limb and riser must never be less than 0.15 (4 mm).

ASYMMETRIC IDLER
Some Browning bows are equipped with a special asymmetric idler wheel, which is assembled on the top limb. It is essential that the idler be oriented properly. The wide edge of the idler always goes to the cable guard side of the bow. The illustration shows the proper orientation of the idler for a right-handed bow when viewed while holding the bow as it is shot.

One or more of the following patents may apply: MANUFACTURED UNDER ONE OR MORE OF THE FOLLOWING PATENTS:
4,967,721 5,335,644 5,678,529 RE36,942 LICENSED 5,141,689 6,237,584 5,005,554 5,339,790 5,762,060 D429,309 UNDER: 5,368,006 6,588,411 5,054,462 5,365,650 5,960,778 D503,958 5,392,756 6,966,314 5,123,396 5,377,658 6,112,732 D528,625 5,241,945 5,243,958 5,280,779 5,301,651 5,307,787 5,469,834 5,487,373 5,495,843 5,507,270 5,657,739 6,176,231 6,360,735 6,792,930 6,889,683 6,968,837 7,347,196 5,505,185 5,782,229 5,894,835

5,501,208

B R O W N I N G

A R C H E R Y

Browning Archery assumes no responsibility for spelling, grammatical or technical errors in this booklet. Browning Archery reserves the right to change, alter or modify any specifications or details of the product line without notice. No portion of this book may be reproduced without the express written consent of the Browning Archery Marketing Department.

IMPORTANT WARRANTY REGISTRATION

THIS FORM MUST BE RECEIVED BY BROWNING ARCHERY WITHIN 30 DAYS OF PURCHASE TO ACTIVATE WARRANTY. SERIAL # OF BOW BOW MODEL YOUR NAME ADDRESS CITY COUNTRY EMAIL ADDRESS DATE PURCHASED / / PHONE ( ) STATE POSTAL CODE ZIP WHERE PURCHASED

Cut out and mail form to: Browning Archery WARRANTY REGISTRATION PO Box 5487 Tucson, Arizona 85703

Compound Bow USERS GUIDE

GET THE LATEST INFORMATION ON BROWNING ARCHERY PRODUCTS YOUR ONLINE SOURCE TO THE WORLD OF BROWNING ARCHERY BOWS AND ACCESSORIES!

www.browning-archery.com
YOUR PURCHASE RECORD
KEEP YOUR RECEIPT AND BOW INFORMATION IN A SAFE LOCATION IN CASE OF FIRE, THEFT OR WARRANTY REPAIR.
SERIAL # OF BOW BOW MODEL YOUR NAME ADDRESS CITY COUNTRY EMAIL ADDRESS DATE PURCHASED / / PHONE ( ) STATE POSTAL CODE ZIP WHERE PURCHASED

ATTACH ORIGINAL RECEIPT HERE

NOTE: DO NOT SEND THIS PAGE WITH YOUR

ORIGINAL RECEIPT INTO BROWNING ARCHERY WARRANTY. THIS PAGE IS FOR YOUR RECORDS ONLY.
11

Compound Bow USERS GUIDE

STATEMENT OF WARRANTY LIMITED CONDITIONS OF PRODUCT WARRANTY
BROWNING BOWS:
a) All metal components carry a 100% warranty against manufacturers defects to the original owner. b) Limbs, composite wheels/cams, grips or other bow components will be covered 100% for five years. After the fifth year, any defective part will be replaced at 50% of replacement cost. c) Strings and buss cables are not covered under this warranty.

Strings and cables will be inspected for wear and replaced, if necessary, on all bows returned to Browning Archery for warranty service. A minimal charge will be assessed for all bows returned to Browning Archery for warranty service. Evidence of abuse, mishandling, or alteration to any Browning Archery product voids any claim to warranty. Browning Archery cannot be held responsible for injury or product failure resulting from improper use, neglect or failure to follow maintenance schedules prescribed by Browning Archery. Browning Archery recommends that all bows undergo string and cable changes every 5,000 shots or every twelve months (whichever comes first) to maintain Browning Archery warranty coverage. Total arrow weight must be a minimum of five grains per pound of bow peak draw weight. Over stressing Browning Archery compound bows by using arrows lighter than the five grain minimum will void the warranty and may cause damage to the bow and possible injury to the shooter. Browning Archery makes no other claims of warranty either expressed or implied. In the interest of product improvement and consumer safety, Browning Archery reserves the right to make changes in product design, color and specifications without notice. In the event a product needs to be returned to Browning Archery please contact Browning Archery Customer Service for a Return Authorization Number and shipping instructions. Please send accompanying documentation, such as dated sales receipt showing the purchase date of the product. If no documentation is received, Browning Archery will utilize the serial number to determine warranty status.

BROWNING ACCESSORIES:
Browning Archery bow quivers (excluding hood liner carry a 100% warranty for five years to the original owner.

Warranty work must be performed by Browning Archery or an authorized Browning Archery dealer.

Contact Browning Archery at 520-838-2004 prior to returning your bow for service or warranty work to obtain a Return Authorization Number.

www.browning-archery.com Browning Archery Tucson, Arizona

BROWNING TRADEMARKS LICENSED FROM BROWNING

PN A826702

REV: 10/08