Scribd
Upload
28 views

Software Verification: EXAMPLE 2-012

This document summarizes a test of SAP2000 software that analyzes plate bending when shear deformations are significant. Three models of an annular plate were created: 1) a thin plate model that only considers bending, 2) a thick plate model that considers both bending and shear, and 3) a thick plate model with increased shear stiffness to minimize shear effects. The deflections predicted by SAP2000 matched the published values for bending in the thin plate model and for combined bending and shear in the thick plate models, validating SAP2000's ability to model plate bending and account for shear deformations.

Uploaded by

Batepola Bac
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
28 views

Software Verification: EXAMPLE 2-012

This document summarizes a test of SAP2000 software that analyzes plate bending when shear deformations are significant. Three models of an annular plate were created: 1) a thin plate model that only considers bending, 2) a thick plate model that considers both bending and shear, and 3) a thick plate model with increased shear stiffness to minimize shear effects. The deflections predicted by SAP2000 matched the published values for bending in the thin plate model and for combined bending and shear in the thick plate models, validating SAP2000's ability to model plate bending and account for shear deformations.

Uploaded by

Batepola Bac
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Software Verification

PROGRAM NAME: REVISION NO.:

SAP2000 0

EXAMPLE 2-012
SHELL PLATE BENDING WHEN SHEAR DEFORMATIONS ARE SIGNIFICANT PROBLEM DESCRIPTION This example is the example shown on page 376 in Roark and Young 1975. It is an annular plate with an inner radius of 1.4 inches, an outer radius of 2 inches and a thickness of 0.5 inch. The plate is simply supported at the inner edge and is loaded with a circular line load at a radius of 1.8 inches. The deflection at the free outer edge is compared with results published in Roark and Young 1975. The results published in Roark and Young 1975 give both the bending and the shear contribution to the edge deflection. Three models are created for the example. The first model (Example 2-012a-thin) uses the thin plate option for the shell elements. Because the thin plate formulation does not include the effects of shear deformations, the results of the thin plate model are expected to compare with the published bending deflection. The second model (Example 2-012a-thick) uses the thick plate option. Because the thick plate formulation does include the effects of shear deformations, the results of the thick plate model are expected to compare with the sum of the published bending and shear deflections. The third model (Example 2-012b-thick) again uses the thick plate option but includes area object shear stiffness modifiers v13 = 1,000 and v23 = 1,000. Those stiffness modifiers make the shell element 1,000 times stiffer in shear and thus make the shear deflection negligible. The results of the thick plate model with shear stiffness modifiers are expected to compare with the published bending deflection. The annular plate is meshed 6x96 (radial by tangential). The circular line load is applied as a distributed load to dummy frame elements. All of the property modifiers for the dummy frame elements are set equal to zero. Thus, the dummy frame elements have no stiffness.

EXAMPLE 2-012 - 1

Software Verification
PROGRAM NAME: REVISION NO.:

SAP2000 0

GEOMETRY, PROPERTIES AND LOADING


Material Properties E = 18,000,000 lb/in2 = 0.3 G = 6,923,077 lb/in2 Y 0.5 inch thick annular plate, simply supported around inner edge, free around outer edge, with a 6 x 96 mesh (radial by tangential) 800 lb/in line load shown dashed

X
d=

In n
O ut

1.8 "

er

loa

rad

ol ine

ius =

er r adiu

diu

st

1 .4

"

s=

Ra

2"
EXAMPLE 2-012 - 2

Software Verification
PROGRAM NAME: REVISION NO.:

SAP2000 0

TECHNICAL FEATURES OF SAP2000 TESTED Plate bending analysis of shell elements when shear deformations are significant Area object stiffness modifiers Frame distributed loads

RESULTS COMPARISON The independent results are published in the example on page 376 in Roark and Young 1975. The published bending deflection is -0.00521 inch, the published shear deflection is -0.000125 inch and the published combined shear and bending deflection is -0.00534 inch.

Model A Thin plate

Output Parameter Uz at outer edge Bending Deflection in Uz at outer edge

SAP2000

Independent

Percent Difference

-0.00522

-0.00521

+0.2%

A Thick plate B Thick plate with shear stiffness modifiers

Bending plus Shear Deflection in Uz at outer edge Bending Deflection in

-0.00534

-0.00534

0%

-0.00521

-0.00521

0%

EXAMPLE 2-012 - 3

Software Verification
PROGRAM NAME: REVISION NO.:

SAP2000 0

COMPUTER FILES: Example 2-012a-thick, Example 2-012a-thin; Example 2-012b-thick CONCLUSION The SAP2000 results show an acceptable comparison with the independent result for the thin plate option and an exact comparison with the independent results for the thick plate option.

EXAMPLE 2-012 - 4

You might also like