ORDER NO.

The illustration shows the VSX-607RDS.

RRV1953

AUDIO/VIDEO MULTI-CHANNEL RECEIVER

VSX-607RDS
VSX-407RDS
Type
HYXKEW HYXKGR

THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

Model VSX-607RDS VSX-407RDS Power Requirement
AC220-230V AC220-230V

The voltage can be converted by the following method.

AC240V, AC240V,

: Alter the wiring of the Power-supply block at the primary winding of Power-transformer referring to the "Line Voltage Selection"
described in Service Manual.

CONTENTS
1. SAFETY INFORMATION ...................................... 2 2. EXPLODED VIEWS AND PARTS LIST ................ 3 3. SCHEMATIC DIAGRAM ....................................... 8 4. PCB CONNECTION DIAGRAM .......................... 24 5. PCB PARTS LIST ............................................... 31 6. ADJUSTMENT .................................................... 35 7. GENERAL INFORMATION ................................ 36 7.1 PARTS ......................................................... 36 7.1.1 IC .......................................................... 36 7.1.2 DISPLAY ............................................... 42 7.2 DISASSEMBLY ........................................... 43 7.3 DIAGNOSIS ................................................. 45 7.4 BLOCK DIAGRAM ....................................... 46 7.5 REMOTE CONTROL UNIT [CU-VSX131 (AXD7169)] ............................ 48 8. PANEL FACILITIES AND SPECIFICATIONS .. 52

PIONEER ELECTRONIC CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 501 Orchard Road, #10-00 Wheelock Place, Singapore 238880

c PIONEER ELECTRONIC CORPORATION 1998

T - IZK MAY 1998 Printed in Japan

VSX-607RDS, VSX-407RDS

1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING Lead in solder used in this product is listed by the California Health and Welfare agency as a known reproductive toxicant which may cause birth defects or other reproductive harm (California Health & Safety Code, Section 25249.5). When servicing or handling circuit boards and other components which contain lead in solder, avoid unprotected skin contact with the solder. Also, when soldering do not inhale any smoke or fumes produced.

NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or be of identical designation.

(slow operating fuse) on PCB indicate that replacement parts must

REMARQUE (POUR MODLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou de remplacement doivent avoir la mme dsignation.

(fusible de type lent) sur CCI indiquent que les pices

(FOR USA MODEL ONLY)

1. SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.

ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.

LEAKAGE CURRENT CHECK

Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5mA.

2. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER.

Device under test Test all exposed metal surfaces

Reading should Leakage not be above current 0.5mA tester

Also test with plug reversed (Using AC adapter plug as required)

Earth ground

AC Leakage Test

VSX-607RDS, VSX-407RDS

2. EXPLODED VIEWS AND PARTS LIST

NOTES:

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on the product are used for disassembly.
(1) PACKING PARTS LIST
Mark No.
1 2 3 NSP 4 5 8 (2/2) 17 8 (1/2) 9 (2/2) 8 9 10 11 12 13 6 NSP 6 7

2.1 PACKING
1 2 4 12 HYXKEW 3 Type Only 13 14 7, 16

Description
FM Antenna AM Loop Antenna Operating Instructions (Italian/Spanish/Portuguese) Warranty Card Remote Control Unit (CU-VSX131) Battery Cover Alkaline Dry Cell Battery (LR6, AA) Left Pad Right Pad Packing Sheet Packing Case Polyethylene Bag (0.03 230 340) Operating Instructions (Dutch/Swedish) Operating Instructions (English/French) Remote Control Unit (CU-VSX130) Dry Cell Battery (R6P, AA) Operating Instructions (German)

Part No.
ADH7005 ATB7009 See Contrast table (2) ARY7010 See Contrast table (2) See Contrast table (2) See Contrast table (2) AHA7203 AHA7204 AHG7028 See Contrast table (2) Z21-038 See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2)

VSX-607RDS 5 Only 15

10

VSX-407RDS Only

14 15 9 (1/2) 11 17 NSP 16

(2) CONTRAST TABLE

VSX-607RDS/HYXKEW, HYXKGR, VSX-407RDS/HYXKEW and HYXKGR are constructed the same except for the following :
Part No. Mark No.
3 5 6 7 11 13 14 15 16 17

Symbol and Description

Operating Instructions (Italian/Spanish/Portuguese) Remote Control Unit (CU-VSX131) Battery Cover Alkaline Dry Cell Battery (LR6, AA) Packing Case Operating Instructions (Dutch/Swedish) Operating Instructions (English/French) Remote Control Unit (CU-VSX130) Dry Cell Battery (R6P, AA) Operating Instructions (German)

VSX-607RDS HYXKEW
ARC7191 AXD7169 Not used AEX1007 AHD7587 ARC7197 ARE7157 Not used Not used ARC7193

VSX-407RDS HYXKEW
ARC7190 Not used RZN1156 Not used AHD7586 ARC7196 ARE7156 AXD7162 AEX7001 ARC7192

Remarks

HYXKGR
Not used AXD7169 Not used AEX1007 AHD7587 Not used Not used Not used Not used ARC7193

HYXKGR
Not used Not used RZN1156 Not used AHD7586 Not used Not used AXD7162 AEX7001 ARC7192

NSP

NSP

VSX-607RDS, VSX-407RDS

2.2 EXTERIOR SECTION

25 18 22 34 34

34 3

34 34
D

34 34

28 (VSX-607RDS Only)

36 1 34
E

34

34

34 20 34

14 17

13

35

35 20 34 12 34 23 10
D

34

VSX-607RDS 29 Only 29 34 34

34
E

26
B

34

24

7 24
F

34 27 Accessory of Front Panel 28 11 VSX-607RDS Only 15

C

34 8

19

34
B A

34

31 34 34 27 34 31 34 34 2 34 21 For VSX-607RDS 34
G

16 32 30 For VSX-407RDS

Accessory of Front Panel 25

Refer to "2.3 FRONT PANEL SECTION". 33

34

VSX-607RDS, VSX-407RDS

(1) EXTERIOR SECTION PARTS LIST

Mark No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 NSP 16 17 18

Description
MOTHER Assy VOLUME DSP Assy CONNECTION Assy HEADPHONE Assy TRANS 1 Assy TRANS 2 Assy PRIMARY Assy FRONT SPEAKER Assy FM/AM TUNER Unit Power Transformer (T1 : AC220-230V/240V)

Part No.
See Contrast table (2) See Contrast table (2) See Contrast table (2) AWX7086 AWX7090 AWX7080 AWX7087 See Contrast table (2) AXX7048 ATS7204

Mark No.
19 20 21 22 23 24 25 26 27 28

Description
T Angle H Angle PCB Angle Top Cover Heat Sink Y

Part No.
ANG7178 ANG7179 ANG7180 AME7373 ANH7083

NSP NSP NSP NSP

NSP

NSP

PCB Support AEC7006 Push Rivet AEC7025 PCB Support AEC7132 Card Spacer AEC7133 5P Shield Cable (J34) See Contrast table (2) (MOTHER CN105, FRONT SPEAKER CN703FRONT INPUT CN571) Screw Insulator Insulator Foot Assy Round Knob Screw Screw Screw ABA1007 See Contrast table (2) PNW2766 See Contrast table (2) AAB7082 BBZ30P080FZK ABA7044 ABA7043

Flexible Cable (J33) See Contrast table (2) (FRONT SPEAKER CN752-MOTHER CN112) Fuse (FU1 : T2A) AEK1057 AC Power Cord ADG7008 Cord Stopper CM-22B Flexible Cable 13P (J32) ADD7094 (MOTHER CN110-FM/AM TUNER Unit) Under Base ANA7070 Rear Panel See Contrast table (2) Bonnet Case AZN7727

29 30 31 32 33 34 35 36

(2) CONTRAST TABLE

VSX-607RDS/HYXKEW, HYXKGR, VSX-407RDS/HYXKEW and HYXKGR are constructed the same except for the following :
Part No. Mark No.
1 2 3 8 11 17 28 30 32

Symbol and Description

MOTHER Assy VOLUME DSP Assy CONNECTION Assy FRONT SPEAKER Assy Flexible Cable (J33) Rear Panel 5P Shield Cable (J34) Insulator Foot Assy

VSX-607RDS HYXKEW
AWX7078 AWX7085 AWX7165 AWX7089 ADD7095 ANC7630 ADX7237 PNW2766 Not used

VSX-407RDS HYXKEW
AWX7077 AWX7084 AWX7079 AWX7088 Not used ANC7629 Not used Not used REC1263

Remarks

HYXKGR
AWX7078 AWX7085 AWX7165 AWX7089 ADD7095 ANC7630 ADX7237 PNW2766 Not used

HYXKGR
AWX7077 AWX7084 AWX7079 AWX7088 Not used ANC7629 Not used Not used REC1263

NSP

NSP

VSX-607RDS, VSX-407RDS

2.3 FRONT PANEL SECTION

12 3 15 11 8 5 12 12

14

13

VSX-607RDS Only 12 12 12

VSX-607RDS Only 2

7 6 (2/2)

10 (1/2)

VSX-607RDS Only 16 10 (2/2)

9 6 (1/2)

(1) FRONT PANEL SECTION PARTS LIST

Mark No.
NSP NSP NSP 1 2 3 4 5 6 7 8 9 10

Description
FRONT Assy FRONT INPUT Assy POWER SW Assy Getter Power Button PTK Function Button PTK PIONEER Badge LED Lens Sheet Sub Panel

Part No.
See Contrast table (2) See Contrast table (2) AWX7061 See Contrast table (2) AAD7457 AAD7456 PAM1755 PNW2019 AAK7580 See Contrast table (2)

Mark No.
11 12 13 14 15 16

Description

Part No.

Front Panel See Contrast table (2) Screw BPZ30P080FMC Flexible Cable 20P (J31) ADD7093 (MOTHER CN109-FRONT CN501) Flexible Cable 20P (J35) ADD7093 (MOTHER CN111-FRONT CN502) Power Button M Screw AAD7442 See Contrast table (2)

(2) CONTRAST TABLE

VSX-607RDS/HYXKEW, HYXKGR, VSX-407RDS/HYXKEW and HYXKGR are constructed the same except for the following :
Part No. Mark No.
1 2 4 10 11

Symbol and Description

FRONT Assy FRONT INPUT Assy Getter Sub Panel Front Panel

VSX-607RDS HYXKEW HYXKGR

AWX7082 AWX7072 AAX7644 AAP7044 AMB7497 ABA7009 AWX7082 AWX7072 AAX7644 AAP7044 AMB7497 ABA7009

VSX-407RDS HYXKEW
AWX7081 Not used AAX7643 AAP7043 AMB7496 Not used

Remarks

HYXKGR
AWX7081 Not used AAX7643 AAP7043 AMB7496 Not used

NSP NSP

16 Screw

VSX-607RDS, VSX-407RDS

VSX-607RDS, VSX-407RDS

3. SCHEMATIC DIAGRAM
3.1 OVERALL CONNECTION DIAGRAM
A

FM/AM TUNER UNIT (AXX7048)

E E 1/2, E 2/2
VOLUME DSP ASSY (AWX7085:VSX-607RDS) (AWX7084:VSX-407RDS)

A A 1/3 A 3/3
MOTHER ASSY (AWX7078:VSX-607RDS) (AWX7077:VSX-407RDS)

VSX-607RDS ONLY

F H
D

FRONT SPEAKER ASSY (AWX7089:VSX-607RDS) (AWX7088:VSX-407RDS)

FRONT INPUT ASSY (AWX7072)

8
1 2 3 4

VSX-607RDS, VSX-407RDS
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".

FRONT ASSY (AWX7082:VSX-607RDS) (AWX7081:VSX-407RDS)

J
POWER SW ASSY (AWX7061)

G
HEADPHONE ASSY (AWX7086)
B

B
CONNECTION ASSY (AWX7165:VSX-607RDS) (AWX7079:VSX-407RDS)

2 ASSY C TRANS (AWX7080)

POWER TRANSFORMER

TRANS 1 ASSY (AWX7090)

PRIMARY ASSY (AWX7087)

AC POWER CORD

AC220230V,240V 50/60Hz

9
5 6 7 8

VSX-607RDS, VSX-407RDS 3.2 MOTHER ASSY (1/3)

A

A 1/3
MOTHER ASSY (AWX7078:VSX-607RDS) (AWX7077:VSX-407RDS)

IC151: PHONO RIAA AMP

IC102: BUFFER AMP

IC101: FUNCTION SW

CN571 VSX-607RDS ONLY

10

A 1/3
1

VSX-607RDS, VSX-407RDS

E 1/2

CN201

E 1/2

CN202
A

(S)

(C)

A 2/3
CN501

A 2/3

D A 3/3 A 2/3
Q191: RIPPLE FILTER FOR TUNER
MTZJ5.1B

A 2/3

A 3/3

FM/AM TUNER UNIT

D : AUDIO SIGNAL ROUTE
(C)

: AUDIO SIGNAL ROUTE(CENTER)

CN752

(S)

: AUDIO SIGNAL ROUTE(SURROUND)

A 1/3
8

11

A 2/3

CN502

VSX-607RDS, VSX-407RDS 3.3 MOTHER ASSY (2/3)

A

A 1/3

A 2/3
MOTHER ASSY (AWX7078:VSX-607RDS) (AWX7077:VSX-407RDS)
IC401(2/2): POWER AMP CENTER

A 1/3

(C)

A 1/3
(C) (C) PAC009A (C)

A 1/3

2SC2705

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. ICP-N25, MFD BY ROHM CO., LTD. FOR IC403.

2SC2705

A 1/3
C

PAC009A

IC401(1/2): POWER AMP FRONT Rch

A 1/3

A 1/3

F
12

J25

J24

A 2/3
1

VSX-607RDS, VSX-407RDS

(C)

(C)

IC402(1/2): POWER AMP FRONT Lch

A 1/3

PAC009A

2SC2705

(C)

2SC2705

(S)

PAC009A

(S)

A 1/3

(S)

IC402(2/2): POWER AMP SURROUND

(S)

(C)

C
(C)

A 1/3

(C)

(C)

(S)

(S)

(S)

(S)

: AUDIO SIGNAL ROUTE

(C)

: AUDIO SIGNAL ROUTE(CENTER)

(S)

: AUDIO SIGNAL ROUTE(SURROUND)

A 3/3

A 2/3
8

13

VSX-607RDS, VSX-407RDS 3.4 MOTHER (3/3), CONNECTION AND TRANS 2 ASSEMBLIES

A

A 3/3
MOTHER ASSY (AWX7078:VSX-607RDS) (AWX7077:VSX-407RDS)

A 2/3

A 1/3
(HP)

C
(HP) (HP)

B
CONNECTION ASSY (AWX7165:VSX-607RDS) (AWX7079:VSX-407RDS)
14

(HP)

A 3/3 B
1

VSX-607RDS, VSX-407RDS

E 1/2 CN203
A

IC651: HEADPHONE AMP

(HP) (HP)

(HP)

(HP)

: AUDIO SIGNAL ROUTE(HEADPHONE)

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 49101.6 MFD, BY LITTELFUSE INK. FOR IC71,IC72 (AEK7012).

C
T1 POWER TRANSFORMER

TRANS 2 ASSY (AWX7080)

1.6A

G
J21

1.6A

G
J22
C

CN952

CN953

(HP)

(HP)

VSX-607RDS ONLY D

A 3/3 B C
8

15

VSX-607RDS, VSX-407RDS 3.5 FRONT ASSY A 1/3 CN109

A

A 1/3

CN111

B S501 : SPEAKERS S502 : SELECT S503 : TAPE2 MONITOR S504 : CHARACTER / SEARCH S505 : TONE() / BALANCE(L) S506 : PHONO S507 : STANDBY / ON S508 : TONE(+) / BALANCE(R) S509 : FM / AM S510 : STATION / FREQUENCY() S511 : DOLBY PRO LOGIC S512 : CD S513 : MEMORY S514 : DOLBY VIRTUAL S515 : DVD / LD S516 : STATION / FREQUENCY(+) S517 : DIRECT S518 : VCR / TAPE1 S519 : EON MODE S520 : DSP MODE S521 : VIDEO INPUT (VSX-607RDS ONLY) S522 : CLASS S523 : TUNING SELECT S524 : RF ATT

REMOTE RECEIVER UNIT

STANDBY IND.

16

D
1

VSX-607RDS, VSX-407RDS

4.332MHz

D
FRONT ASSY (AWX7082:VSX-607RDS) (AWX7081:VSX-407RDS)
FL TUBE

D VSX-607RDS ONLY

D
8

17

VSX-607RDS, VSX-407RDS 3.6 VOLUME DSP ASSY (1/2)

E 1/2
A

VOLUME DSP ASSY (AWX7085:VSX-607RDS) (AWX7084:VSX-407RDS)

IC206: 44kHz L.P.F.

(C)

(S)

(C)

(C)

(S)

(C) (S)
(C)

VSX-407RDS ONLY
(C)

(C) (S) (S)

(S)

(S)

VSX-607RDS ONLY

IC205(BU4052BCF) CONTROL

A 1/3
18

CN108

E 1/2
1

(S)

(C)

VSX-607RDS, VSX-407RDS

: AUDIO SIGNAL ROUTE

(C)

: AUDIO SIGNAL ROUTE(CENTER)

MTZJ9.1B

(S) (HP)

: AUDIO SIGNAL ROUTE(SURROUND) : AUDIO SIGNAL ROUTE(HEADPHONE)

IC207: 6dB AMP IC202: TONE CONTROL

E 2/2

E 2/2 E 2/2

(C)

(C) (C)

E 2/2

(S) (S) (S)

E 2/2
IC211: 44kHz L.P.F. & AMP

E 2/2 E 2/2
(S) (C)
(HP)

E 2/2

(S)

(C)

A 3/3 A 1/3
5

CN106

CN107

E 1/2
8

19

VSX-607RDS, VSX-407RDS 3.7 VOLUME DSP ASSY (2/2)

E 2/2
A

VOLUME DSP ASSY (AWX7085:VSX-607RDS) (AWX7084:VSX-407RDS)

E 1/2 E 1/2
VSX-407RDS ONLY

E 1/2
VSX-607RDS ONLY B

E 1/2
IC208,IC209: MIXER(Fch+SW)

E 1/2
IC204(BU4052BCF) CONTROL

: AUDIO SIGNAL ROUTE

(C)

: AUDIO SIGNAL ROUTE(CENTER) D

(S)

: AUDIO SIGNAL ROUTE(SURROUND)

20

E 2/2
1

VSX-607RDS, VSX-407RDS

IC301: PRE-AMP

E 1/2

Q311 KRA101M

E 1/2

IC302: PRE-AMP

E 1/2

(C) (C)

(C) (C)

E 1/2
(S)

C
(S)

E 1/2

(S)

(S)

E 1/2

E 2/2
8

21

VSX-607RDS, VSX-407RDS 3.8 FRONT SPEAKER, HEADPHONE, FRONT INPUT, TRANS 1, POWER SW AND PRIMARY ASSEMBLIES
A

FRONT SPEAKER ASSY (AWX7089:VSX-607RDS) (AWX7088:VSX-407RDS)

0.01

CN403

VSX-407RDS ONLY
0.01 0.01

CN402

A 2/3

A 2/3

VSX-607RDS ONLY

H
CN571

VSX-407RDS ONLY VSX-607RDS ONLY

VSX-607RDS ONLY

VSX-607RDS ONLY

IC801: VIDEO SW
Q802 2SA933S

0.01

CN701:

VSX-607RDS ONLY

9604S-10C

IC751: ELECTRONIC VOLUME

IC752(1/2):INVERTER
D
IC801(NJM2279D) LOGIC

: AUDIO SIGNAL ROUTE

22

F
1

A 1/3

IC752(2/2): INVERTED MIXER(SL+SR)

M62429P

CN112

VSX-607RDS, VSX-407RDS

NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS ONLY.

I
TRANS 1 ASSY (AWX7090)
220230

K
FU1:AEK1057

PRIMARY ASSY (AWX7087)

10000p/250

T1 POWER TRANSFORMER

T2A 10000p/250

AC POWER CORD

POWER SW ASSY (AWX7061)

POWER

ATT1193

B
NC AC AC

G
C
CN71

HEADPHONE ASSY (AWX7086)

VSX-607RDS ONLY

INPUT ASSY H FRONT (AWX7072)

B
CN93

A 1/3
CN105

F
CN703
C

C
CN72

B
CN94

(HP)

JA951

(HP)
955

(HP)

: AUDIO SIGNAL ROUTE(HEADPHONE)

G H I J K
7 8

23

VSX-607RDS, VSX-407RDS

4. PCB CONNECTION DIAGRAM

4.1 MOTHER ASSY
NOTE FOR PCB DIAGRAMS :
A

A MOTHER ASSY

CN201 CN752

F T

1. Part numbers in PCB diagrams match those in the schematic diagrams. 2. A comparison between the main parts of PCB and schematic diagrams is shown below.
Symbol In PCB Diagrams Symbol In Schematic Diagrams B C E B C E Part Name

B C E B B C E D D G S G S D G S C E B C E

Transistor

Transistor with resistor

Field effect transistor

Resistor array

B
3-terminal regulator

D
CN501

3. The parts mounted on this PCB include all necessary parts for several destinations. For further information for respective destinations, be sure to check with the schematic diagram. 4. View point of PCB diagrams.

H
CN571

Connector

Capacitor

SIDE A

D
CN502

P.C.Board
C

Chip Part

SIDE B

F
J25

F
J24

SIDE A
IC151 Q101 Q406 IC101 Q458 Q102 Q192 Q103 Q457 Q456 Q455 Q405 Q452 IC402Q454 IC102 Q453 Q

24

A
1

VSX-607RDS, VSX-407RDS
FM/AM TUNER UNIT

E
CN202
A

752

E
CN203

B
CN92

B
CN91

(ANP7244-A) Q103 Q453 Q457 Q191 Q605 Q451 IC403 Q401 Q407 Q403 IC602 Q404 IC401 Q408 IC603 Q402 IC601 IC606 IC607 Q651 Q654 IC651

A
8

25

VSX-607RDS, VSX-407RDS 4.2 CONNECTION, TRANS 2 AND FRONT ASSEMBLIES

A

B CONNECTION ASSY

A CN602

A CN601

D FRONT ASSY

Q503

Q581 Q582

IC581

Q501 Q583 Q502

SIDE A
26

B D
1

VSX-607RDS, VSX-407RDS

C TRANS 2 ASSY
G J22 G J21

T1 POWER TRANSFORMER
(ANP7244-A)
B

G CN952

G CN953 A CN111 A CN109

IC501

(ANP7245-B) IC501 Q504 Q505

D

SIDE A

B C D
8

27

VSX-607RDS, VSX-407RDS 4.3 VOLUME DSP ASSY

E
A

VOLUME DSP ASSY

A
CN108

IC201 IC206

IC205 B IC202
IC202

A
CN107

Q202

IC211 Q311 IC302 IC207

IC301 Q313Q316 IC208

IC209

A
CN106
Q302 VR301

IC204 Q301
IC204

(ANP7245-B)

SIDE A
28

E
1

VSX-607RDS, VSX-407RDS 4.4 FRONT SPEAKER, HEADPHONE AND FRONT INPUT ASSEMBLIES

F FRONT SPEAKER ASSY

A CN112
Q701Q704 Q801Q802 IC801 IC751 IC752

A CN403

A CN402 B CN94

G
HEADPHONE ASSY
B
CN93

K
J23
C

C CN71

C CN72

A
CN105
(ANP7245-B)

H FRONT INPUT ASSY

SIDE A
1 2 3

F G H
4

29

VSX-607RDS, VSX-407RDS 4.5 TRANS 1, POWER SW AND PRIMARY ASSEMBLIES

Line Voltage Selection
A
Line Voltage can be changed by the following modification: 1. Disconnect the AC power cord. 2. Remove the cover. 3. Change the connection wire from TRANS 1 ASSY [Terminal No. (J) or (K)] to PRIMARY ASSY (Terminal No. J1) as follows. Voltage Terminal No. of TRANS 1 ASSY 220-230V (J) 240V (K) 4. Stick a line voltage label on the rear panel. Description Part No. 220V label AAX-193 240V label AAX-192

I
TRANS 1 ASSY

J
POWER SW ASSY
B

220-230V 240V

T1 POWER TRANSFORMER

(ANP7244-A)

(ANP7245-B)

K
PRIMARY ASSY
C

G
CN951

AC POWER CORD
D
(ANP7245-B)

SIDE A
30

I J K
1

VSX-607RDS, VSX-407RDS
Mark No. Description Part No. Mark No. Description Part No.

5. PCB PARTS LIST

NOTES:

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples.

Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%). 561 ........................................................ RD1/4PU 5 6 1 J 560 56 101 473 ........................................................ RD1/4PU 4 7 3 J 47k 47 103 0.5 R50 ..................................................................................... RN2H R 5 0 K 1 1R0 ..................................................................................... RS1P 1 R 0 K Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5621 ...................................................... RN1/4PC 5 6 2 1 F 5.62k 562 101

LIST OF WHOLE PCB ASSEMBLIES

Part No. Mark Symbol and Description VSX-607RDS HYXKEW
NSP MAIN ASSY MOTHER ASSY NSP CONNECTION ASSY NSP TRANS 2 ASSY POWER SW ASSY NSP NSP COMPLEX ASSY FRONT ASSY VOLUME DSP ASSY FRONT SPEAKER ASSY NSP HEADPHONE ASSY NSP FRONT INPUT ASSY TRANS 1 ASSY NSP PRIMARY ASSY AWK7436 AWX7078 AWX7165 AWX7080 AWX7061 AWK7441 AWX7082 AWX7085 AWX7089 AWX7086 AWX7072 AWX7090 AWX7087

VSX-407RDS HYXKEW
AWK7435 AWX7077 AWX7079 AWX7080 AWX7061 AWK7440 AWX7081 AWX7084 AWX7088 AWX7086 Not used AWX7090 AWX7087

Remarks

HYXKGR
AWK7436 AWX7078 AWX7165 AWX7080 AWX7061 AWK7441 AWX7082 AWX7085 AWX7089 AWX7086 AWX7072 AWX7090 AWX7087

HYXKGR
AWK7435 AWX7077 AWX7079 AWX7080 AWX7061 AWK7440 AWX7081 AWX7084 AWX7088 AWX7086 Not used AWX7090 AWX7087

Mark No.

Description

Part No.

Mark No.

Description

Part No.
NJM79M12FA PAC009A TC9163AN UPC4570C 2SC1740S 2SC2240 2SC2705 2SC2878 2SC2878 2SK246 KRA103M KRC101M 1SS254 1SS254 D5SBA20(B) MTZJ27B MTZJ5.1B MTZJ6.8A S5688G

A MOTHER ASSY
(1) CONTRAST TABLE
AWX7078 and AWX7077 are constructed the same except for the following :
Mark Symbol and Description Q101,Q102 Q103 D101,D102 R131 R133,R134 R196,R197
CN105 KR CONNECTOR 3P CN112 10P CONNECTOR

IC602 IC401,IC402 IC101 IC102 Q191,Q192,Q405,Q406 Q403,Q404,Q453,Q454 Q407,Q408,Q457,Q458 Q401,Q402,Q451,Q452 Q651-Q654 Q101,Q102 Q103,Q455 Q456,Q605 D101-D103,D401-D406 D451-D458 D601 D623 D190,D191 D624 D603-D606

Part No. AWX7078 AWX7077 2SK246 Not used KRA103M Not used 1SS254 Not used RD1/4PU474J Not used RD1/4PU475J Not used RD1/4PU102J B3B-PH-K-S 9604S-10C VEF1040 Not used Not used Not used Not used

Remarks

PCB BINDER

(2) PARTS LIST FOR AWX7078 SEMICONDUCTORS

IC403 IC151 IC651 IC603,IC606 IC601 ICP-N25 M5220P NJM4558D-D NJM78M05FA NJM78M12FA

COILS
L451,L452 AF CHOKE COIL (0.7mH) ATH1004 L151-L154 LAU221J L191 LFA470J

RELAY
RY401 ASR7001

31

VSX-607RDS, VSX-407RDS
Mark No. Description Part No.
ACH7015 ACH7016 CCCSL101J50 CCCSL121J50 CCCSL151J50 CCCSL221J50 CCCSL331J50 CCCSL331J50 CEANP2R2M50 CEANP2R2M2A CEANP4R7M50 CEANP4R7M50 CEAT100M50 CEAT101M10 CEAT101M16 CEAT101M16 CEAT101M25 CEAT101M35 CEAT101M6R3 CEAT102M25 CEAT1R0M50 CEAT221M10 CEAT221M25 CEAT222M25 CEAT2R2M50 CEAT470M10 CEAT470M25 CEHAQ100M2A CEZA1R0M50 CEZA2R2M50 CFTYA224J50 CGCYX103M16 CKCYB471K50 CKCYB681K50 CKCYF103Z50 CKCYF103Z50 CKCYF103Z50 CKCYF103Z50 CKCYF222Z50 CKPUYB102K50 CKPUYF103Z25 CQMA242J50 CQMBA822J50 CQMXA103J2A

Mark No.
101 103 CN102 CN401 CN105 CN602 CN108 CN107 CN106 CN601

Description
6P PIN JACK 4P PIN JACK 4P PIN JACK 6P SPEAKER TERMINAL KR CONNECTOR 3P 14P PLUG 15P PLUG 20P PLUG 6P PLUG 10P SOCKET PCB BINDER EARTH METAL FITTING

Part No.
AKB7012 AKB7014 AKB7015 AKE7020 B3B-PH-K-S KM200TA14 KM200TA15 KM200TA20 KM200TA6 KP250NA10 VEF1040 VNF-091

CAPACITORS
C601 (6800 F/56V) C602 (6800 F/56V) C121-C123,C151,C152 C405,C406,C455,C456 C157,C158 C101-C112,C422,C471 C127,C128,C403,C404 C453,C454 C415,C416,C465,C466 C417,C420,C467,C469 C129,C130,C401,C402 C451,C452 C155,C156,C653,C654 C190,C192,C625 C191,C409,C410,C459,C460 C657,C658 C609,C610 C624 C411,C461 C606 C194,C407,C458 C423 C626 C605 C167,C168 C612,C628 C161,C162 C425,C426,C477,C478 C408,C457 C125,C126 C473-C476 C199,C482,C484 C159,C160,C421 C472 C119,C120,C131,C132 C169,C170,C430,C490 C607,C608,C611,C627 C651,C652 C481 C197 C193 C165,C166 C163,C164 C479,C480

B CONNECTION ASSY
(1) CONTRAST TABLE
AWX7165 and AWX7079 are constructed the same except for the following :
Mark Symbol and Description PCB BINDER Part No. AWX7165 AWX7079 VEF1040 Not used Remarks

(2) PARTS LIST FOR AWX7165 OTHERS

CN91,CN93 10P PLUG CN92,CN94 14P SOCKET PCB BINDER KM250NA10L KP200TA14L VEF1040

C TRANS 2 ASSY
SEMICONDUCTORS
IC71,IC72 (1.6A) AEK7012

CAPACITORS
C71,C72 (1F/100V) C74 ACH1237 CEANPR10M50

RESISTORS
R71,R72 Other Resistors RD1/4PMF100J RD1/4PM J

OTHERS
CN72 CN71
12P JUMPER CONNECTOR 3P JUMPER CONNECTOR

RESISTORS
R413,R414,R463,R464(0.22 ,5W) R190 R425,R426,R475,R476 R663,R664 R411,R412,R461,R462 R477,R478,R481,R482 R629 R601 Other Resistors ACN7035 RD1/2PM391J RD1/4MUF101J RD1/4MUF330J RD1/4MUF820J RD1/4PMF4R7J RS1LMF561J RS2LMF330J RD1/4PU J

PCB BINDER

KPD12 KPD3 VEF1040

D FRONT ASSY
(1) CONTRAST TABLE
AWX7082 and AWX7081 are constructed the same except for the following :
Mark Symbol and Description Part No. AWX7082 1SS254 ASG1034 AWX7081 Not used Not used Remarks

OTHERS
CN402 8P JUMPER CONNECTOR CN403 9P JUMPER CONNECTOR CN112 10P FFC CONNECTOR CN110 13P FFC CONNECTOR CN109,CN111 20P FFC CONNECTOR 52147-0810 52147-0910 9604S-10C 9604S-13C 9604S-20C

D517 S521

32

VSX-607RDS, VSX-407RDS
Mark No. Description Part No. Mark No. Description Part No.

(2) PARTS LIST FOR AWX7082 SEMICONDUCTORS

IC581 IC501 Q581 Q505 Q583 Q501 Q503 Q502,Q504,Q582 D501,D503-D521 D502 BU1923 PDG212A 2SA1115 2SA933S 2SC1740S KRA101M KRA103M KRC101M 1SS254 BR3371XJ30A

VOLUME DSP ASSY

(1) CONTRAST TABLE

AWX7085 and AWX7084 are constructed the same except for the following :
Mark Symbol and Description IC205 IC208,IC209 C237-C240 C261,C262 R233,R234 R237,R238 R239-R244 R254,R255 Part No. AWX7085 AWX7084 BU4052BCF Not used NJM4558LD Not used CKCYF103Z50 Not used CEAT4R7M50 Not used RD1/4PU273J Not used RD1/4PU563J RD1/4PU223J RD1/4PU102J Not used Not used Not used Remarks

COILS
L501,L581 L502 LAU2R2J LAUR22J

SWITCHES
S501-S524 ASG1034

(2) PARTS LIST FOR AWX7085 SEMICONDUCTORS

IC204,IC205 IC201 IC202 IC211 IC206-IC209 IC301,IC302 Q313,Q315 Q202 Q314,Q316 Q301,Q302 Q311 D301-D303 D201,D203 D204 BU4052BCF CXD2724Q M62420FP NJM4558D-D NJM4558LD UPC4570C 2SA1115 2SC1740S 2SC2603 2SK246 KRA101M 1SS254 MTZJ5.6B MTZJ9.1B

CAPACITORS
C514 C587,C588 C590 C586 C589 C512 C517 C504,C581 C511 C518 C513 C505 C582 C510 C507-C509 C523,C583,C585 C584 C501,C502 C503,C516,C522 ACH7013 CCCCH270J50 CEAL101M6R3 CEAT101M10 CEAT1R0M50 CEAT221M10 CEAT221M35 CEAT2R2M50 CEAT470M50 CFTYA104J50 CGCYX103M16 CGCYX104M16 CGCYX472M25 CKCYF103Z50 CKPUYB101K50 CKPUYB102K50 CKPUYB561K50 CKPUYF103Z25 CKPUYF473Z16

COILS
L202,L208 L207 LAU1R0J LAU220J

CAPACITORS
C251-C254 C204,C209,C265 C301,C302 C206,C207 C321,C322 C332 C241,C242 C246,C259,C263,C331 C247,C248 C230 C201,C202 C203,C282 C221,C222,C229,C231-C236 C255,C256,C261,C262 C311-C314 C211,C212 C305-C308 C227,C228 C223,C224 C225,C226 C303,C304 C243,C244,C249,C250,C284 C213,C214,C237-C240 C257,C258,C309,C310 C315,C316 CCCCH121J50 CCCSL101J50 CCCSL271J50 CCPUCH120J50 CCPUSL470J50 CEANP100M50 CEANP4R7M50 CEAT101M10 CEAT1R0M50 CEAT221M10 CEAT470M16 CEAT471M6R3 CEAT4R7M50 CEAT4R7M50 CEAT4R7M50 CEATR22M50 CEZA4R7M50 CFTLA103J50 CFTLA223J50 CFTLA474J50 CFTYA473J50 CGCYX102K25 CKCYF103Z50 CKCYF103Z50 CKCYF103Z50

RESISTORS
All Resistors RD1/4PU J

OTHERS
X581 CRYSTAL RESONATOR ASS7004 (4.332MHz) X501 CERAMIC RESONATOR ASS7018 (7.2MHz) CN501,CN502 20P FFC CONNECTOR 9607S-20F V501 501 FL TUBE AAV7053 REMOTE RECEIVER UNIT GP1U27X

33

VSX-607RDS, VSX-407RDS
Mark No. Description Part No.
CKPUYB101K50 CKPUYB102K50 CKPUYB221K50 CKPUYB331K50 CKPUYF103Z25

Mark No.

Description

Part No.

C264,C266 C215,C216 C323,C324 C205,C208,C217-C220 C271

(2) PARTS LIST FOR AWX7089 SEMICONDUCTORS

IC751 IC801 IC752 Q802 Q801 Q701,Q703 Q702,Q704 D803-D806 M62429P NJM2279D NJM4558LD 2SA933S 2SC1740S KRA103M KRC101M 1SS254

RESISTORS
VR301 (100k ) Other Resistors ACX7034 RD1/4PU J

OTHERS
X201 CRYSTAL RESONATOR (33.8688MHz) CN201 15P SOCKET CN202 20P SOCKET CN203 6P SOCKET ASS7002 KP200TA15L KP200TA20L KP200TA6L

COILS
L701,L702 AF CHOKE COIL ATH1004

RELAYS
RY701,RY702 ASR7001

FRONT SPEAKER ASSY

CAPACITORS
C756,C757 C761,C763,C804,C805 C801-C803 C806,C807 C751,C752 C755 C758,C759 C753,C754,C760 C701-C704 C808,C809 C709 C762,C764 C765,C810,C851 C705-C708 CCCSL101J50 CCCSL221J50 CEAT100M50 CEAT101M10 CEAT1R0M50 CEAT470M10 CEAT470M16 CEAT4R7M50 CFTYA224J50 CKCYF103Z50 CKPUYB101K50 CKPUYB221K50 CKPUYF103Z25 CQMXA103J2A

(1) CONTRAST TABLE

AWX7089 and AWX7088 are constructed the same except for the following :
Mark Symbol and Description IC751 IC752 Q703 Q704 D804,D806 RY702 C707,C708 C751,C752 C753,C754,C760 C755 C756,C757 C758,C759 C761,C763 C762,C764 C765 C803 C811 R711,R712,R751 R752 R753,R754 R755,R759 R756 R757,R758 R760 R765,R766 CN701
8P SPEAKER TERMINAL

Part No. AWX7089 AWX7088 M62429P Not used NJM4558LD Not used KRA103M Not used KRC101M Not used 1SS254 Not used ASR7001 CQMXA103J2A CEAT1R0M50 CEAT4R7M50 CEAT470M10 CCCSL101J50 CEAT470M16 CCCSL221J50 CKPUYB221K50 CKPUYF103Z25 Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used

Remarks

RESISTORS
R701-R704 Other Resistors RD1/4PMF4R7J RD1/4PU J

CEAT100M50 Not used Not used CGCYX104M16 RD1/4PU103J Not used RD1/4PU471J Not used RD1/4PU121J Not used RD1/4PU123J RD1/4PU362J RD1/4PU153J RD1/4PU223J RD1/4PU104J AKE7044 Not used Not used Not used Not used Not used Not used Not used AKE7049 Not used Not used Not used

OTHERS
CN752 CN702 CN751 JA801 CN701 CN703 J25 J24 JA851 10P FFC CONNECTOR 1P PIN JACK 4P PIN JACK 4P PIN JACK (YELLOW) 8P SPEAKER TERMINAL KR CONNECTOR JUMPER WIRE 9P JUMPER WIRE 8P REMOTE CONTROL JACK 9604S-10C AKB7042 AKB7087 AKB7100 AKE7044 B2B-PH-K-S D20PYY0810E D20PYY0915E RKN1004

CN701
SPEAKER TERMINAL

CN703 KR CONNECTOR B2B-PH-K-S CN751 4P PIN JACK CN752

10P FFC CONNECTOR

AKB7087 9604S-10C

34

VSX-607RDS, VSX-407RDS
Mark No. Description Part No. Mark No. Description Part No.

G HEADPHONE ASSY
SEMICONDUCTORS
D91,D92 D961,D962 1SS254 S5688G

K PRIMARY ASSY
SEMICONDUCTORS
IC901 Q901 D905,D906 D904 D901,D902 NJM78M56FA KRC101M 1SS254 MTZJ5.1A S5688G

RELAY
RY91 ASR7012

CAPACITORS
C961 C962 C952,C953 C951 C954 CEANP470M25 CEAT470M50 CGCYX103M16 CGCYX473M16 CKCYF103Z50

COIL
L901 LINE FILTER ATF-151

TRANSFORMER
T901 ATT1193

RESISTORS
All Resistors RD1/4PU J

RELAY
RY901 ASR7013

OTHERS
951 952 CN953 CN952 CN951 3P CABLE HOLDER 12P CABLE HOLDER 14P PLUG 10P SOCKET 4P JUMPER CONNECTOR 51052-0300 51052-1200 KM200TA14 KP250NA10 KPE4 RKN1002 VNF-091

CAPACITORS
C901,C902 (10000pF/AC250V) C904 C903 C905-C907 ACG7020 CEAT470M16 CEAT471M16 CKCYF103Z50

RESISTORS
R905 Other Resistors RD1/2PM470J RD1/4PU J

JA951 HEADPHONE JACK EARTH METAL FITTING

OTHERS

FRONT INPUT ASSY

C574,C575 C571-C573 CGCYX473M16 CKPUYB221K50

CAPACITORS

902 3P CABLE HOLDER 906 4P CABLE HOLDER H901,H902 FUSE CLIP EARTH METAL FITTING J23 JUMPER WIRE 4P J26 JUMPER WIRE 3P

51063-0305 51063-0405 AKR1003 VNF-091 D15A04-250-2651 D15A03-250-2651

RESISTORS
All Resistors RD1/4PU J

OTHERS
JA571 3P PIN JACK (GOLD) CN571 KR CONNECTOR AKB7098 B5B-PH-K-S

I J

TRANS 1 ASSY
No service parts.

6. ADJUSTMENT
POWER SW ASSY
S51 ASG1035

There is no information to be shown in this chapter.

SWITCH CAPACITORS
C51,C52 CGCYX103K25

OTHERS
CN51 3P JUMPER CONNECTOR KPE3

35

VSX-607RDS, VSX-407RDS

7. GENERAL INFORMATION
7.1 PARTS
7.1.1 IC
The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.

PAC009A (MOTHER ASSY : IC401, IC402)

2 ch AF Power Amplifier

Pin Arrangement

22

Block Diagram
14 TR4 1 C1 R2 3 4 R4 TR3 C4 R7 TR10 TR11 R1 9 R9 R8 TR13 5 7 8 10 11 12 15 16 6 17 18 D1 TR24 R16 C6 R10 TR12 TR23 TR1 TR2 R3 D2 D3 R13 TR16 TR7 TR5 R17 C3 TR6 R5 R6 TR8 TR9 TR22 R15 TR20 R12 19 TR21 R14 C5 TR19 C2 R11 TR15 TR14 20 22 13 R18 TR18 TR17

21

36

VSX-607RDS, VSX-407RDS

PDG212A (FRONT ASSY : IC501)

Mode Control IC
PB5/SCK1 PB2/SCK0 PB6/SI1 PB3/SI0 PE7/T0 PE6 PE5
3

Pin Arrangement

24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

PA3/AN3 PA4/AN4 PA5/AN5 PA6/AN6 PA7/AN7 RST EXTAL XTAL Vss PD0/S0 PD1/S1 PD2/S2 PD3/S3 PD4/S4 PD5/S5 PD6/S6

PE3//INT3
1 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65

PB0/CINT

PE4/RMC

PB7/SO1

PB4/SO0

PC7/KR7

PC6/KR6

PC5/KR5

PC4/KR4

PC3/KR3

PC2/KR2

PC1/KR1

PC0/KR0

PA2/AN2

PA1/AN1

PA0/AN0

PB1/CS0

25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

P2/IN2 PE1/EC1/INT1 PE0/EC0/INT0 PG3 PG2 PG1 PG0 NC VDD VFDP T0 T1 T2 T3 T4 T5

T9/S27

PF2/S10

PF3/S11

PF4/S12

PF5/S13

PF6/S14

PF7/S15

T15/S21

T14/S22

T13/S23

T12/S24

T11/S25

T10/S26

PD7/S7

PF0/S8

PF1/S9

T8/S28

T7

S16

S17

S18

S19

Pin Function
No.
1 2 3

Pin Name
PE3/INT3 PE4/RMC PE5

I/O
I I I

Function Name
TUNED REMOCON STEREO

S20

Function
"L" inputs when TUNER is TUNE state. Only when IF count is right (when lighting is permitted), "TUNED" indicator in the FL can be turned on after the IF count. Inputs the remote control receiver output When TUNER receives stereophonic broadcasting, "L" input. Ignore it at the time of forced MONO. "STEREO" indicator in the FL turned on when TUNED is "L" and STEREO is "L" at the "TUNED" indicator lighting is permitted. ON and OFF the Transistor switch for VDD of the RDS decoder. "L" for AM and "H" for FM without relation to the FUNCTION. MUTE control of the TUNER output Data input from the PLL IC Read-in the IF frequency by this data. Request outputs from the microprocessor. Chip enable of serial control of the TUNER PLL IC Clock of serial control of the TUNER PLL IC Data of serial control of the TUNER PLL IC ON and OFF the transistor switch for AC power relay Stand-by : "L" , Power ON : "H" pin 12 : pin 13 : Not used Key scan input SP A H L SP A+B H H SP OFF L L

4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

PE6 PE7/T0 PB0/CINT PB1/CS0 PB2/SCK0 PB3/SIO PB4/SOO PB5/SCK1 PB6/SI1 PB7/SO1 PC0/KR0 PC1/KR1 PC2/KR2 PC3/KR3 PC4/KR4 PC5/KR5 PC6/KR6 PC7/KR7 PA0/AN0 PA1/AN1

O O I O O O O O O O I I I I I O O OL O O

FM+ T. MUTE PLL DO PLL CE PLL CK PLL DA AC RY PROT RY A+B RY NC KEY IN1 KEY IN2 KEY IN3 D.C.DET. O.L.DET. DIRECT 6CH RY NC FUNC. ST FUNC. DA

DC detector input of the protection circuit When "L" is input, open relays excepting AC relay. 8-figures section of FL flashes as "POWEROFF" at "L". pin 19 : pin 20 : Not used Serial control strobe of the function IC (TC9163AN) Control the Function IC and DSP IC with the serial control data DSP/BYPATH L L At 6 ch input H L DIRECT L H MUTE H H

T6

37

VSX-607RDS, VSX-407RDS
No.
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80

Pin Name
PA2/AN2 PA3/AN3 PA4/AN4 PA5/AN5 PA6/AN6 PA7/AN7 RST EXTAL XTAL Vss PD0/S0 PD1/S1 PD2/S2 PD3/S3 PD4/S4 PD5/S5 PD6/S6 PD7/S7 PF0/S8 PF1/S9 PF2/S10 PF3/S11 PF4/S12 PF5/S13 PF6/S14 PF7/S15 S16 S17 S18 S19 S20 T15/S21 T14/S22 T13/S23 T12/S24 T11/S25 T10/S26 T9/S27 T8/S28 T7 T6 T5 T4 T3 T2 T1 T0 VFDP VDD NC PG0 PG1 PG2 PG3 PE0/EC0/INT0 PE1/EC1/INT1 PE2/IN2

I/O
O O O I O O OL O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O OL OL I I I

Function Name
FUNC. CK XLAT RESET (DSP) REDY TONE DA E. VOL DA RST EXTAL XTAL Vss NC SURROUND RY LOUNDNESS A. MUTE V. MUTE V. CONT A V. CONT B FL Seg 21 FL Seg 20 FL Seg 19 FL Seg 18 FL Seg 17/KO10 FL Seg 16/KO9 FL Seg 15/KO8 FL Seg 14/KO7 FL Seg 13/KO6 FL Seg 12/KO5 FL Seg 11/KO4 FL Seg 10/KO3 FL Seg 9/KO2 FL Seg 8/KO1 FL Seg 7 FL Seg 6 FL Seg 5 FL Seg 4 FL Seg 3 FL Seg 2 FL Seg 1 FL Grid. 9 FL Grid. 8 FL Grid. 7 FL Grid. 6 FL Grid. 5 FL Grid. 4 FL Grid. 3 FL Grid. 2 FL Grid. 1 VFDP 5V 5V VOL. DOWN VOL. UP NC NC WAKE UP RDS CK RDS DA Power supply Power supply Power supply Motor volume control Motor volume control Not used Not used AC wake up input Serial control CLK of RDS communication Serial control DATA of RDS communication VOL DOWN : L VOL UP : L FL driver FL driver FL driver / Key scan out FL driver Serial control latch of the DSP IC (CXD2724Q) Reset DSP IC (CXD2724Q)

Function
Control the FUNCTION IC, DSP IC, TONE IC and E. VOL IC with the serial control clock

For communicating with DSP IC (CXD2724Q) L :Inhibit the data transfer Serial control data of TONE IC (M62420FP) Serial control data of E. VOL IC (M62429P) Reset Connect the crystal resonator (7.7MHz or 7.2MHz) Ground Not used ON and OFF the transistor switch for SURROUND relay On and OFF the transistor switch of LOUNDNESS ON : Lights up "LOUNDNESS" character in FL DIRECT ON : Forced OFF Control the system mute control of the AUDIO system Control the VIDEO IC (NJM2279D) Control the VIDEO IC (NJM2279D) Control the VIDEO IC (NJM2279D)

H :Permit the data transfer

VCR :H, DVD :H, F.V. :H, AUDIO system :L VCR :L, DVD :L, F.V. :H, AUDIO system :L VCR :L, DVD :H, F.V. :H, AUDIO system :L

38

VSX-607RDS, VSX-407RDS

BU1923 (FRONT ASSY : IC581)

Radio Data System (RDS) Demodulation IC

Pin Arrangement
QUAL RDATA VREF MUX VDD1 VSS1 VSS3 CMP 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 RCLK

Block Diagram
MUX 4
120k
100k

VSS3 7

CMP 8

(NC) XO XI VDD2 VSS2

VDD2 12 VREF 3

100k

8 th Switched Capacitor Filter

Anti-Aliasing Filter

Comparator

16 RCLK

VDD1 5 VSS1 6

ANALOG

1 QUAL PLL 57kHz RDS/ARI PLL 1187.5Hz BIPHASE DECODER

DEFFERENTIAL DECODER

2 RDATA

DIGITAL

T1 T2

VSS2 11 CLOCK
13 14

TEST
10

XI

XO

T1

9 T2

Pin Function
No. Pin Name 1 2 3 4 5 6 7 8 QUAL RDATA VREF MUX VDD1 VSS1 VSS3 CMP Comparator Analog power supply ( 4.5V to 5.5V) Function Demodulation quality fine data :H , error data :L Demodulation data Reference power supply (1/2 VDD1) Composite signal input No. Pin Name 9 T2 Function Test input H : stops the internal clock , L or open : movements Test input Open or connect to GND.

10 T1 11 VSS2 12 VDD2 13 XI 14 XO 15 (NC) 16 RCLK

Digital power supply (4.5V to 5.5V) Connect the crystal resonator (4.332MHz) Non connection Demodulation clock (1187.5kHZ)

39

VSX-607RDS, VSX-407RDS

CXD2724Q (VOLUME DSP ASSY : IC201)

DSP IC Block Diagram
27

24k bit DELAY RAM RVDT 50 SCK 46 XLAT 49 READY 47 LRCK 58 BCK 57 SI 55 XMST 60 MICRO COMPUTER I/F DSP SERIAL DATA I/F
CLOCK GENERATOR /TIMING CIRCUIT

LIN LO1 RIN LO2 LOUT ROUT

ADC1

26 38

ADC2
Analog SW

39

DAC1 DAC2
Analog SW

23

42

DAC3 DAC4

Trim Vol

30

XCOUT XSOUT

Trim Vol

35

33

32

17

XTLI XTLO BFOT

Pin Function
No. 1-3 4 5-8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Pin Name T.P VSS0 T.P TST0 VDD0 VSS1 TST1 TST2 TST3 TST4 XRST BFOT CSL1 CSL2 VSS2 AVS3 AVD3 LOUT AVD1 AVS1 LO1 LIN AVD5 AVS5 XCOUT AVDX XTLO I/O O O I I I I I I O I I O O I O O Function Monitor pin for test Normally, outputs "L". Digital ground Monitor pin for test Normally, outputs "L". Test pin Normally, fix to L. Digital power supply Digital ground Test pin Normally, fix to "L". Test pin Normally, fix to "L". Test pin Normally, fix to "L". Test pin Normally, fix to "L". System reset input L : reset. Clock and divided frequency output (384/768/256/512 fs) Test pin Normally, fix to "H". Test pin Normally, fix to "L". Digital ground Ground for L-ch D/A converter Power supply for L-ch D/A converter L-ch A/D converter output Power supply for L-ch A/D converter Ground for L-ch A/D converter OP amp. inverting output for LPF of L-ch A/D converter Analog input of L-ch A/D converter Power supply for C-ch D/A converter Ground for C-ch D/A converter C-ch D/A converter output Analog power supply for master clock Crystal oscillation circuit output

40

VSX-607RDS, VSX-407RDS

No. 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61-63 64 65-72 73 74 75-80

Pin Name XTLI AVSX XSOUT AVS6 AVD6 RIN LO2 AVS2 AVD2 ROUT AVD4 AVS4 VSS3 SCK REDY T.P XLAT RVDT XS24 VDD1 VSS4 T.P SI T.P BCK LRCK VSS5 XMST T.P VSS6 T.P VDD2 VSS7 T.P

I/O I O I O O I O I I I I I/O I/O I O O O

Function Crystal oscillation circuit input Analog ground for master clock S-ch D/A converter output Ground for S-ch D/A converter Power supply for S-ch D/A converter Analog input of R-ch A/D converter OP amp. inverting output for LPF of R-ch A/D converter Ground for R-ch A/D converter Power supply for R-ch A/D converter R-ch D/A converter output Power supply for R-ch D/A converter Ground for R-ch D/A converter Digital ground Shift clock input of microprocessor interface Transfer permission signal output of microprocessor interface L : Transfer prohibition Monitor pin for test Normally, outputs "Hi-Z". Latch input of microprocessor interface Data input of microprocessor interface 24/32 bit slot selection of serial data L : 24 bit slot (It is effective at slave mode.) Digital power supply Digital ground Monitor pin for test Normally, outputs "L". Serial data input of 1 sampling 2 channel Input pin for test Normelly, outputs "L". Serial bit transfer clock of serial input/output data SI and SO Sampling frequency clock of serial input/output data SI and SO Digital ground Master/slave mode switching input of BCK and LRCK L : master mode Monitor pin for test Normally, outputs "L". Digital ground Monitor pin for test Normally, outputs "L". Digital power supply Digital ground Monitor pin for test Normally, outputs "L".

41

VSX-607RDS, VSX-407RDS

7.1.2 DISPLAY AAV7053 (FRONT ASSY : V501)

FL TUBE
1G
S2 S1 a1 j a2 S4 S3

k b

g e r

m p c n S5

1
2G 3G 4G 5G 6G 7G 8G 9G

43
(2G - 9G)
b1 Dp2 b2 Dp1

(1G)

ANODE AND GRID ASSIGNMENT

1G P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 S5 2G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2 3G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2 4G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2 5G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2 6G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2 7G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2 8G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2 9G a1 a2 h j k b f m g c e r p n d1 d2 Dp1 S1, S3 S4 S2 Dp2

PIN ASSIGNMENT
Pin No. Connection
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

F1 F1 NP NP 1G 2G 3G 4G 5G 6G 7G 8G 9G NX NX NX NX NX P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 P19 P20 P21 NP NP F2 F2

42

VSX-607RDS, VSX-407RDS 7.2 DISASSEMBLY

7.2.1 Bonnet and FRONT Assy
BONNET
1 1 1 1 2 1

FRONT ASSY

9
Release Binder CONNECTION ASSY Front Panel J35

1 5 1 6 2 3 3 4 2 8
CN105

J31

7
CN703

MOTHER ASSY

FRONT SPEAKER ASSY

10

10

VSX-607RDS 10 Only

FRONT ASSY

43

VSX-607RDS, VSX-407RDS

7.2.2 MOTHER and CONNECTION Assemblies

MOTHER AND CONNECTION ASSEMBLIES

2 2

2 2

9 4 2

3 6
CONNECTION ASSY Rivet

5
Cutting Pliers

MOTHER ASSY

10

44

VSX-607RDS, VSX-407RDS

7.3 DIAGNOSIS
POWER AMPLIFIER IC (MOTHER ASSY : IC401 and IC402) (At Bottom Side)

Cut six portions on the Under Base by nipper and remove a Cover. Front

Turn the Cover.

4 2
Diagnose the POWER AMPLIFIER IC (IC401 and IC402).

Fix the Cover with the four screws (BBZ30P080FMC). Front

Front
1

IC401

22 1

IC402

22

CAUTION : After cutting it with the nipper, dispose of it not to injure by touching the cut part to an user's hand.

45

46
IC101 TC9163AN FUNCTION SW TP-L3 TP-L4
5 7 43 2 7 1

TAPE2 IN IC202 M62420FP TONE

TAPE2 OUT

FM/AM TUNER UN IT TP-L1 TP-R1

6 23 3 1 38 27 5 7 FL 3

IC151 M5220P

PHONO IC201 CXD2724Q DSP

23 19 14 35 S 30 C FR 5 7 1 3

RIAA

CD IC102 UPC4570C BUFFER TP-L2 TP-R2 TP-R3 TP-R4

IC206 NJM4558LD LPF fc = 44kHz

IC207 NJM4558LD +6dB GAIN

VCR/TAPE

7.4 BLOCK DIAGRAM

LD/DVD

VCR/TAPE OUT Q101, Q102

VSX-607RDS, VSX-407RDS

VIDEO

DIRECT 5 7 1 3 3 L 12 3 1

DIRECT

IC651 NJM4558D-D H.P. AMP.

15

TP-L5 TP-L6

HEADPHONE SPEAKER A TP-L9

12

13

RY701 TP-L8

Q451
20 R 15

TP-L7

IC301 MASTER VR UPC4570C TP-R5 TP-R6 PRE-AMP. IC402 PAC009A POWER AMP.
5 7

RY701 TP-R8 TP-R9 SPEAKER A

Q452

TP-R7

IC204 BU4052BCF DIRECT/STEREO/6ch SW TP-C4

20 5 7 C 15

TP-C3

RY401 IC401 PAC009A POWER AMP.

3 S 12

SPEAKER CENTER TP-C6

IC211 NJM4558D-D TP-S4 LPF fc = 44kHz IC302 UPC4570C TP-S5 PRE-AMP. Q401
3 1

RY401 Q402 TP-S7 MONITOR OUT

SPEAKER SURROUND

LD/DVD
+6dB

3 10

VCR/TAPE
+6dB

12 5

IC801 NJM2279D VIDEO SW

VIDEO

VCR REC OUT

VSX-607RDS, VSX-407RDS

Test Points for Diagnosis

MOTHER ASSY

TP-L1 TP-R1
IC102

IC101

TP-L7

TP-C6 TP-L8 TP-S7 TP-R8 TP-R7

IC604 IC605

IC402

IC401

VOLUME DSP ASSY

TP-L2 TP-R2
IC201

IC205

TP-L3 TP-R3
IC202

TP-S4 TP-C3

FRONT SPEAKER ASSY

TP-L9 TP-R9
IC751 IC801 IC752

IC211

TP-R4 TP-L4
IC302

TP-C4
IC301

TP-S5 TP-L6 TP-R6 TP-R5 TP-L5

IC204

Fig.1 Test Point Location

47

VSX-607RDS, VSX-407RDS 7.5 REMOTE CONTROL UNIT [CU-VSX131 (AXD7169)] (VSX-607RDS ONLY)
7.5.1 EXPLODED VIEWS AND PARTS LIST
NOTES:

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on the product are used for disassembly.
Parts List
Mark No.
1 2 3 4 5
9 15 16 12

Description
Filter Name Plate Rubber Sheet (A) Rubber Sheet (B) Spring (+) Spring () Spring Screw Remo-con Case (A) Remo-con Case (B) Battery Cover Main Key (FF) Main Key (STOP) Main Key (REV) Main Key (PAUSE) Main Key (PLAY) PCB

Part No.
AZA7152 AZA7301 AZA7289 AZA7300 AZB7049 AZB7050 AZB7051 AZB7052 AZN7712 AZN7326 AZN7327 AZN7666 AZN7329 AZN7665 AZN7331 AZN7664 AZW7243

6 7 8 9 10
13

14

11 12 13 14 15
4

NSP

16 17

3 17

5 6

10 7

8 11

48

VSX-607RDS, VSX-407RDS
7.5.2 SCHEMATIC DIAGRAM
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
SWITCHES K01 K02 K03 K04 K05 K06 K07 K08 K09 K10 K11 K12 K13 K14 K15 K16 K17 K18 K19 K20 K21 K22 K23 K24 K25 K26 K27 K28 K29 K30 K32 K33 K35 K36 K37 K38 K41 :0 :1 :2 :3 :4 :5 :6 :7 :8 :9 : : : SET UP : MODE CHK : MULTI OPE. : SYS. OFF : : : ENT. : POWER : CH: CH+ : DISC : +10 : VOL.: VOL.+ : TV FUNC. : TV POWER : AMP POW. : MUTING : FUNCTION : DVD : CD : VCR1 : TV CONT. : TUNER : SURROUND

49
1 2 3 4

VSX-607RDS, VSX-407RDS

7.5.3 PCB DIAGRAM

A

50
1 2 3 4

VSX-607RDS, VSX-407RDS

7.5.4 PCB PARTS LIST

NOTES:

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples.

Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%). 561 ........................................................ RD1/4PU 5 6 1 J 560 56 101 473 ........................................................ RD1/4PU 4 7 3 J 47k 47 103 0.5 R50 ..................................................................................... RN2H R 5 0 K 1 1R0 ..................................................................................... RS1P 1 R 0 K Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5621 ...................................................... RN1/4PC 5 6 2 1 F 5.62k 562 101

Mark No.
IC1 IC2 IC3,IC4 IC5 Q4

Description

Part No.
AZC7281 AZC7280 TC74HC07AF RH5VA21AA 2SA1037K 2SC3265 SE1003-C SPS-503C-3 CL-230HR-CD RLS-73

SEMICONDUCTORS

Q1-Q3 D1,D3,D7 D2 D8,D9,D12,D13,D15,D16 D4-D6

CAPACITORS
C2 C4-C7,C11 C3 C1 C10 CEJA470M10 CKSQYB104K25 CEJA221M6R3 CEJA101M6R3 CCSQCH101J50

RESISTORS
R2001,R2002 R1,R2,R4 Other Resistors RS1/8S0R0J RS1/8S3R9J RS1/10S J

OTHERS
X1,X2 CERAMIC RESONATOR KBR-4.0M (4MHz)

51

VSX-607RDS, VSX-407RDS

8. PANEL FACILITIES AND SPECIFICATIONS

8.1 PANEL FACILITIES
Front Panel
The size of characters in the figure may different from that on the actual product.

AUDIO/VIDEO MULTI-CHANNEL RECEIVER

DOLBY SURROUND P R O L O G I C

STANDBY DSP MODE DOLBY VIRTUAL

EON MODE STANDBY/ON

MEMORY

RF ATT

CLASS

MASTER VOLUME

CHARACTER /SEARCH

STATION

+ +

TUNING SELECT

DIRECT

DOLBY PRO LOGIC

FREQUENCY

SPEAKERS

VIDEO

L AUDIO R

VIDEO INPUT

VCR/ TAPE 1

DVD/LD

CD

FM/AM

PHONO

TAPE 2 MONITOR

SELECT

TONE

+
MIN MAX

PHONES DVD 5.1CH L BALANCE R

EON

1 2 3 4 5 6 7

Power switch STANDBY indicator STANDBY/ON button CHARACTER/SEARCH button EON MODE button MEMORY button RF ATT button
Set this button to on when receiving strong FM signals (nearby stations) to reduce sound distortion. Normally, this button should be set off. This button does not affect AM reception.

= ~ ! @ #

DSP MODE button DOLBY VIRTUAL button DOLBY PRO LOGIC button MASTER VOLUME SPEAKERS button
Switches as follows with each press (FRONT SPEAKER only).
3A 3 A+B OFF 2

8 CLASS button 9 TUNING SELECT, STATION (, +) and FREQUENCY (, +) buttons

TUNING SELECT: Use to select the STATION mode and FREQUENCY mode when operating the tuner. STATION mode:
SP A

$ PHONES jack (Headphone terminal) % VIDEO INPUT button/terminals

Connect to a video camera, etc. Press the VIDEO INPUT button to switch the function to VIDEO.

FREQUENCY mode:
SP A

^ Remote sensor & Function buttons * SELECT, TONE (, +) and BALANCE (L, R) buttons
SELECT: Use to select the TONE (TREBLE, BASS) and BALANCE control.
3 TREBLE control 3 BASS control BALANCE control 2

STATION (, +): Use to select the station number when operating the tuner. FREQUENCY (, +): Use to select the frequency when operating the tuner.

0 Display - DIRECT button

Use to play back sound without going through the tone and balance control circuits. DOLBY PRO LOGIC, DSP MODE, DOLBY VIRTUAL and LOUDNESS also turn off.

TONE (, +): Use to adjust tone. BALANCE (L, R): Use to adjust volume balance.

52

VSX-607RDS, VSX-407RDS

Display

SP AB DIRECT LOUDNESS PRO LOGIC VIRTUAL

DSP TAPE 2

EON RDS RF ATT MONO TUNED STEREO

1 SPEAKERS A, B indicator
The indicator of the FRONT SPEAKER (A, A and B) selected will light.

8 EON MODE indicator

Lights when EON MODE is ON.

2 DIRECT indicator
Lights when DIRECT is ON.

9 RDS indicator
Lights when RDS broadcast is received.

0 RF ATT indicator 3 LOUDNESS indicator

Lights when LOUDNESS is ON.

- CHARACTER display = TUNER indicator

MONO: Lights when the monaural mode is set using the MPX MODE button. TUNED: Lights when broadcasts are being received. STEREO: Lights when stereo broadcasts are received during auto stereo mode.

4 PRO LOGIC indicator

Lights when Dolby Pro Logic is selected.

5 VIRTUAL indicator
Lights when DOLBY VIRTUAL is selected.

6 DSP indicator
Lights when HALL, JAZZ, DANCE, THEATER 1 and THEATER 2 has been selected with the DSP MODE button.

7 TAPE 2 indicator
Lights when TAPE 2 MONITOR is ON.

53

VSX-607RDS, VSX-407RDS

Connecting Devices
When connecting or changing equipment, be sure to turn OFF the POWER switch, and disconnect the power cord from the wall outlet.

7 For better reception of signals, use the FM external antenna.

LOOP ANTENNA

7 When AM broadcast reception is poor

Connect a 5 to 6 meter long vinyl-coated wire to the AM antenna. If possible draw horizontally outdoors to achieve better reception. AM outdoor antenna AM indoor antenna (Vinyl-coated wire) 5 to 6 m
LOOP ANTENNA

AM

AM
GND

FM UNBAL 75

GND

75 coaxial cable

Don't detach the AM loop antenna.

FM UNBAL 75

FM antenna

The sub woofer can be connected in a different way. For details, refer Sub woofer with to the instructions on the sub woofer. TV monitor built-in amplifier

Speaker
R

7Assembling the AM loop antenna

Stretch out fully and secure onto the wall using pins.

VIDEO IN

DVD 5.1CH INPUT LOOP ANTENNA AM

CONTROL

VIDEO OUT

TO MONITOR TV VIDEO OUT SUB WOOFER

SUB WOOFER CENTER

OUT

7When attached on a wall, etc.

SIGNAL GND is used to decrease the noises when an analog player, etc. is connected. This is not a ground for safety.

FM UNBAL 75 IN

SURR. RIGHT IN PLAY

SURR. LEFT OUT REC

B
VIDEO IN FRONT IN VIDEO IN IN PLAY PRE OUT OUT REC

IN

L
ANTENNA

L
CENTER SPEAKER

R
PHONO SIGNAL GND TAPE2 MONITOR CD DVD/ LD VCR/ TAPE1

AUDIO/VIDEO IN AUDIO/ VIDEO OUT VIDEO OUT

VCR

PLAY OUTPUT

REC INPUT

AUDIO OUT
CD

AUDIO OUT

Analog player

Cassete deck

Face towards the direction with the best reception.

CD player LD player VCR Can also be con- C a n a l s o b e nected to a DVD connected to a player. cassette deck.

54

VSX-607RDS, VSX-407RDS

7 AM Antenna terminal
Twist the wire core.

7 Input/output plug

7 Speaker terminal
Twist the wire core.

3
VID E IN O

L
10 mm

m mm 10 0m 1
Twist the wire core.

2 3

Connect the white plug to L, red plug to R, and yellow plug to VIDEO. Be sure to insert completely.

2 1 3

The size of characters and terminal positions in the figures may differ from those on the actual product.

7 Front Panel
Speaker system (Front)
R L
AUDIO/VIDEO MULTI-CHANNEL RECEIVER STANDBY EON MODE STANDBY/ON MEMORY RF ATT CLASS

CHARACTER /SEARCH

STATION

+ +

TUNING SELECT

FREQUENCY

SPEAKERS

VIDEO

L AUDIO R

VIDEO INPUT

PHONES

VIDEO OUT
FRONT SPEAKERS

AUDIO OUT

Connect to equipment such as a video camera, etc.

CAUTION: SPEAKER IMPEDANCE
8~16 / SPEAKER

A
ATTENTION: IMPEDANCE DE
HAUT-PARLEURS 8~16 / HAUT-PARLEUR

SURROUND SPEAKERS

MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES. DOLBY, PRO LOGIC AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF DOLBY LABORATORIES.

memo
Speaker (Center) Speaker system (Surround)

Use nominal impedances ranging from 8 to 16 for the speaker system.

55

VSX-607RDS, VSX-407RDS

DVD 5.1-Channel Input Terminals

When using DVD/LD functions, the unit supports both 2-channel and 5.1-channel input. When the 5.1-channel mode is selected, SURROUND L, R, CENTER and SUB WOOFER terminal are enabled, thus allowing the connection of a Dolby Digital decoder or DVD player with 5.1-channel output. memo 5.1-channel inputs are supported only during use of the DVD/LD function. Other functions cannot be used with 5.1-channel input.

[Connection Example]
DVD player with 5.1-channel output (built in Dolby Digital decoder)

DVD 5.1 CH INPUT

LOOP ANTENNA AM

CONTROL

VIDEO OUT

TO MONITOR TV VIDEO OUT SUB WOOFER

SUB WOOFER CENTER

VIDEO

OUT

CENTER SURROUND L L FRONT

FM UNBAL 75

SURR. RIGHT IN PLAY

SURR. LEFT OUT REC

VIDEO IN FRONT IN

VIDEO IN IN PLAY

PRE OUT OUT REC

IN

IN

R
ANTENNA

SUB WOOFER

R
PHONO SIGNAL GND TAPE2 MONITOR CD DVD/ LD VCR/ TAPE1

56

VSX-607RDS, VSX-407RDS

Remote Control Unit

6 MULTI CONTROL function buttons
RECEIVER TV

Used to set and operate the MULTI CONTROL, and switch the function. TV CONTROL: Press to operate TV.

G TIN MU
MPX

FQ +

TV FU NC
DISP. MODE

7 SURROUND button
Press when performing surround operations.

ENTER
FQ

8 Number/surround setting buttons [When set to SURROUND (OPERATIONS)]

PRO LOGIC: Switches the DOLBY PRO LOGIC. DSP MODE: Switches the surround effects. VIRTUAL: Turns the DOLBY VIRTUAL ON/OFF. 5.1CH: Use to set the DVD 5.1-channel input mode. CENTER , +: Adjusts the center level. REAR , +: Adjusts the rear (surround) level. TEST TONE: When turned ON (while in DOLBY PRO LOGIC or DVD 5.1-channel input mode), volume balance adjustment signals are output in order from the speakers and can be adjusted. DIRECT: Use to playback sound without going through the tone and balance control circuits. DOLBY PRO LOGIC, DSP MODE, DOLBY VIRTUAL and LOUDNESS also turn off. LOUDNESS: When LOUDNESS is turned ON at a small volume, the low frequency and high frequency levels increase, enabling the sound to be easier to hear.

VOL
CHANNEL

VOL

MULTI CONTROL

DVD/LD VCR
TV CONTROL SURROUND

CD TUNER

PRO LOGIC DSP MODE VIRTUAL

5.1CH

1
CENTER

2 6 0

3
REAR

4 8
DISC

5
TEST TONE

7 +10

DIRECT LOUDNESS CLASS TV/VCR MODE CHECK

9
FUNCTION

MULTI COMMANDER OPERATION SYSTEM OFF SET UP

[Tuner Operations]
MULTI CONTROL COMMANDER PRE-PROGRAMMED AND LEARNING

Number buttons: Use for setting the frequency value when the station call is selected or during direct access. CLASS: Switches the CLASS (A/B/C). DISC: Use to set the Direct Access mode.

1 RECEIVER power button 2 MUTING button

Press to mute the volume.

[VCR operations]
Number buttons: Use to select the channel of the TV tuner in the VCR. TV/VCR: Switches between TV/VCR.

3 [When set to SURROUND (OPERATIONS)]

%, , @, # (Select/Adjust) buttons

[CD Operations]
DISC: Use to select the DISC number.

[When set to other than SURROUND (OPERATIONS)]

*(Pause), & (Stop), !(Rewind), (Fast Forward), ENTER/# (Play) buttons

9 FUNCTION button
Switches the function.

0 MULTI OPERATION button

Use to operate the multi operation.

[Tuner Operations]
FQ +, FQ , MPX, DISP. MODE, #(FM/AM) buttons MPX: Use to switch the auto stereo/monaural mode for receiving FM broadcasts. When the received broadcast signal is weak, press this button to set the monaural mode.

(Power) button
Turns ON/OFF the power of devices other than this unit.

= TV buttons ~ MODE CHECK button ! COMMANDER SET UP button

Use to control and learn operations of other manufacturers' equipment, and set multi operation functions.

4 VOL (, +) buttons 5 [TV Operations]

Selects the TV broadcast channel.

@ SYSTEM OFF button

Use to turn OFF the power of all equipment connected to the main unit.

[Tuner Operations]
Select the Tuner station.

[CD, LD, DVD Operations]

$, (Chapter/Track Search) buttons.

57

VSX-607RDS, VSX-407RDS

8.2 SPECIFICATIONS
Amplifier Section

Continuous rated power output of 65 watts per channel, min., at 8 ohms, from 40 Hz to 20,000 Hz with no more than 0.09 % total harmonic distortion (front).

FM Tuner Section
Frequency Range ......................................... 87.5 MHz to 108 MHz Usable Sensitivity ..................... Mono: 15.2 dBf, IHF (1.5 V/75 ) 50 dB Quieting Sensitivity ....................................... Mono: 20.2 dBf Stereo: 41.2 dBf Signal-to-Noise Ratio ................................ Mono: 76 dB (at 85 dBf) Stereo: 72 dB (at 85 dBf) Distortion ........................................................ Stereo: 0.6 % (1kHz) Alternate Channel Selectivity ................................ 70 dB (400 kHz) Stereo Separation ..................................................... 40 dB (1 kHz) Frequency Response .............................. 30 Hz to 15 kHz ( 1) dB Antenna Input ....................................................... 75 unbalanced Sensitivity (DIN) ..................................... Mono: 1.1 V (S/N 26 dB) Stereo: 50 V (S/N 46 dB) Signal-to-Noise Ratio (DIN) ........................................ Mono: 62 dB Stereo: 58 dB

Continuous Power Output (DIN, 1 kHz, T.H.D. 1 %, 8 ) STEREO Front ........................................... 70 W + 70 W SURROUND Front ........................................... 50 W + 50 W Center ..................................................... 50 W Rear ........................................................ 50 W Input (Sensitivity/Impedance) PHONO MM .......................................................... 2.8 mV/47 k CD, VCR/TAPE 1, TAPE 2, DVD/LD, VIDEO ........ 200 mV/47 k Phono Overload Level (T.H.D. 0.1 %, 1kHz) PHONO MM ...................................................................... 90 mV Frequency Response PHONO MM ................................... 20 Hz to 20,000 Hz 0.5 dB CD, VCR/TAPE 1, TAPE 2, +0 DVD/LD, VIDEO ................................... 5 Hz to 100,000 Hz 3 dB Output (Level/Impedance) VCR/TAPE 1 REC, TAPE 2 REC ............................ 200 mV/1 k Tone Control BASS .................................................................. 8 dB (150 Hz) TREBLE ............................................................. 8 dB (10 kHz) LOUDNESS ................................. +8 dB/+6 dB (100 Hz/10 kHz) Signal-to-Noise Ratio [DIN (Rated power output/50 mW)] PHONO MM ............................................................ 68 dB/61 dB CD, VCR/TAPE 1, TAPE 2, DVD/LD, VIDEO ........... 86 dB/63 dB Direct: ON Measured by Audio Spectrum Analyzer.

AM Tuner Section
Frequency Range .......................................... 531 kHz to 1,602 kHz Sensitivity (IHF, Loop antenna) ....................................... 350 V/m Selectivity ............................................................................... 30 dB Signal-to-Noise Ratio ............................................................. 50 dB Antenna ..................................................................... Loop antenna

Miscellaneous
Power Requirements ................................. AC 220-230 V, 50/60 Hz Power Consumption .............................................................. 170 W Dimensions ................................. 420 (W) 143 (H) 334 (D) mm Weight (without package) ...................................................... 6.7 kg

Furnished Parts
FM Antenna .................................................................................. 1 AM Loop Antenna ......................................................................... 1 Dry Cell Batteries [size AA (IEC LR6)] ........................................ 2 Remote Control Unit ..................................................................... 1 Operating Instructions ................................................................... 1 Warranty card ................................................................................ 1 NOTE: Specifications and the design are subject to possible modifications without notice, due to improvements.

VIDEO Section
Input (Sensitivity/Impedance) VCR/TAPE 1, DVD/LD, VIDEO ................................. 1 Vp-p/75 Output (Level/Impedance) VCR/TAPE 1, REC, MONITOR TV ........................... 1 Vp-p/75 Frequency Response VCR/TAPE 1, DVD/LD, VIDEO +0 = MONITOR ................................................ 5 Hz to 7 MHz 3 dB Signal-to-Noise Ratio ............................................................. 55 dB Cross Talk .............................................................................. 55 dB

Manufactured under license from Dolby Laboratories Licensing Corporation. Dolby, the double-D symbol and Pro Logic are trademarks of Dolby Laboratories Licensing Corporation.

Accessories

FM antenna ADH7005

AM loop antenna ATB7009

(VSX-607RDS) Remote control unit AXD7169(CU-VSX131)

(VSX-407RDS) Remote control unit AXD7162(CU-VSX130)

Alkaline dry cell battery (size "AA" IEC LR6) x 2 : VSX-607RDS Dry cell battery (size "AA" IEC R6P) x 2 : VSX-407RDS

58