Scribd
Upload
233 views

Statue of Liberty, U.S.A.: Assembly Instructions

Writing the number of each section on its back side before cutting out the sections is highly recommended. Indicates sections that should be glued first, then cut out. Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children.

Uploaded by

Maricruz Valverde Vasquez
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
233 views

Statue of Liberty, U.S.A.: Assembly Instructions

Writing the number of each section on its back side before cutting out the sections is highly recommended. Indicates sections that should be glued first, then cut out. Glue, scissors and other tools may be dangerous to young children so be sure to keep them out of the reach of young children.

Uploaded by

Maricruz Valverde Vasquez
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 0

Indicates where sections should be glued together.

Before starting assembly:Writing the number of each section on its


back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting
out the sections.)
Indicates where to insert sections.
Do not glue the sections together.
Indicates sections that should be glued first,
then cut out.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.

Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Tools and materials
Assembly tip
Caution
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
Photo of competed model
Assembly Instructions:Six A4 sheets(No.1 to No.6)
*This model was designed for Papercraft and may differ from the original in some respects.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C
http://www.canon.com/c-park/en/
Miniature stand Star-shaped stand
Choose the stand
you like best.
Build parts 2 and 4 in the same way.
Attach the
reinforcement
with glue first.
Align and glue the rear
surfaces together.
Align and glue the rear surfaces together.
Align and glue the rear surfaces together.
Build four identical versions of part 10.
View of completed model
Fold these parts inward and align
and glue their surfaces together.
Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C
Align and glue the
rear surfaces together.
Position the short side
on this side
Position the elevator
entrance on this side.
*Glue the parts together in
the sequence shown in steps 1 - 6.
Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C
Curve the interior side
of this part.
View from rear
Position so that the narrower
side is located on this side.
After positioning the rear surfaces
of the side parts together,
glue the rear sides of the corners together.
Insert and glue to
the rear surface.
* Cover the statue with the upper robe.
No gluing is necessary.
Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C
Cut after gluing
the rear surfaces
together.
Glue the rear
surfaces together.
Glue the rear panels of parts 41 and 43,
between which the four sheets of part 42
are sandwiched.
Glue the statue's
fingertips here.
Fold the fingertips inward
and glue to the Declaration of Independence.
Lightly bend this part as
shown in the illustration.
Insert to assembled
part 47 along this line.
Insert and glue the glue tabs
to the interior side of this spot.
Glue to part 29 on the interior side.
Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C
Miniature stand
*Position in place. No gluing needed.
Finished!
Statue of Liberty, U.S.A.: Assembly Instructions Canon is a registered trademark of Canon Inc. Canon Inc. Hiroshi Chiba / PAPERART-C
Star-shaped stand
*Position in place without gluing.
*Place this part on the stand without gluing.
Finished!

You might also like