E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

Authorized distributor:

PRINTED IN U.S.A. 7308-796 COPYRIGHT 1996 CARR LANE MANUFACTURING CO.

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

GENERAL INFORMATION
TOGGLE-ACTION PRINCIPLES: adjustability. Two flanged washers hold the spindle in place
A toggle clamp is a quick-acting mechanical linkage where anywhere along the arm by tightening the jam nuts.
two of the elements make up a toggle action. Actuating the
clamp first moves it into position, then applies clamping
force by compressing or stretching the linkage elements
after contacting the workpiece, then positively locks it by
moving the toggle action’s center pivot past the centerline
of the other two pivots, against a stop.

SOLID-ARM CLAMPS:
Solid-arm hold-down clamps are easily customized to a
particular application. Using the weld-on bolt retainer, you
can locate the spindle permanently in one place. The solid-
arm version allows mounting the spindle at an angle, or
shortening the clamping arm.

1 2 3
Moving into Applying Locking
position clamping force over center

HOLDING CAPACITY: TOP-GRADE MATERIALS:

Carr Lane toggle clamps are made from only the finest-
The “holding capacity” listed for each clamp refers to the
quality materials. Steel clamps are made from various
maximum external force that clamp can safely resist in its
types including 1008, 1010, 1018, and other fine steels.
locked position without incurring any permanent deforma-
Pivot pins on most clamp models are 400-series stainless
tion. For hold-down clamps, holding capacity is measured
steel for extra durability. Many pivot points have hardened
with the spindle as close as possible to the handle, and will
steel bushings for long life. Forged steel components, such
be less at the end of the clamping arm.
as those on toggle pliers and push/pull clamps, are made
from high-carbon steel. Many push/pull-clamp bases are
made of nodular iron for wear resistance.

FINISHES:
Most steel clamps are zinc plated, unless otherwise noted.
Virtually all clamps are also available with a black oxide fin-
ish as specials.

Spindle position for Spindle position for STAINLESS STEEL:

maximum capacity maximum reach Many toggle-clamp models are available in 300-series
stainless steel. These corrosion-resistant clamps are useful
in chemical environments, plating operations, food pro-
cessing, salt-spray environments, medical equipment, elec-
CLAMPING FORCE: tronics fixturing, EDM fixturing, and marine environments.
Clamping force, the amount of force actually applied to the
Various stainless steel grades, including 303 and 304, are
workpiece by closing and locking the clamp, is generally less
used. Clamps normally furnished with a flat-cushion spindle
than the stated holding capacity. This allows the clamp to
in the steel version are supplied with a stainless steel hex-
have ample capacity to resist external machining forces.
head spindle. Other clamps are available in stainless steel
Actual clamping force depends on many factors including:
as specials.
spindle position, proper spindle-height adjustment, spindle
cushioning (uncushioned hex-head spindles provide the
greatest force), workpiece material, and the clamp's mechan-
AIR-POWERED CLAMPS:
The air cylinders on power toggle clamps have Buna N
ical advantage. In most cases, roughly 1/2 of the stated hold-
seals, rated for operating temperatures of -20° to +200° F.
ing capacity can be applied by hand with medium effort.
Note: Zinc plating also deteriorates at temperatures above
250°F.
OPEN-ARM CLAMPS:
Open-arm hold-down clamps offer maximum flexibility and

IFC-TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
INDEX

Horizontal-Handle Hold-Down Clamps . . 3-12

Vertical-Handle Hold-Down Clamps . . . 13-40

Push / Pull Clamps . . . . . . . . . . . . . . . . 41-53

Toggle Edge Clamps . . . . . . . . . . . . . . 54-55

Latch-Action Clamps . . . . . . . . . . . . . . 56-63

Toggle Pliers . . . . . . . . . . . . . . . . . . . . . 64-68

Air-Powered Clamps. . . . . . . . . . . . . . . 69-77

Toggle Clamp Accessories................................................................................................................................78-82

(Rev. 7/10) 1TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE CLAMP CONVERSION CHART
Reference Carr Lane Page Reference Carr Lane Page Reference Carr Lane Page Reference Carr Lane Page
Part No. Part No. No. Part No. Part No. No. Part No. Part No. No. Part No. Part No. No.
AO-100* CL-1000-PTC 72 202943* CL-14112-SA-S 79 240208* CL-38314-FC 79 503* CL-320-HVTC 30
AO-1200* CL-3000-PTC 74 205-S CL-150-HTC 4 245-S CL-600-HTC 9 503-B* CL-310-HVTC 30
AO-200* CL-1000-PTC 72 205-SB CL-151-HTC 4 245-U CL-650-HTC 9 503-LB* CL-311-HVTC 31
AO-2000(HD)* CL-3000-PTC 74 205-SL CL-153-HTC 4 245943* CL-12234-SA-S 78 505* CL-520-HVTC 30
AO-400* CL-2000-PTC 73 205-SR CL-152-HTC 4 247-S CL-750-VTC 22 505-B* CL-510-HVTC 30
AO-800* CL-2000-PTC 73 205-SSS CL-150-HTC-S 4 247-SB CL-751-VTC 22 505-LB* CL-511-HVTC 31
C-800 CL-850-VTC 22 205-U CL-250-HTC 4 247-U CL-850-VTC 22 506* CL-620-HVTC 30
GLBU1* CL-111-HVTC 31 205-UB CL-251-HTC 4 247-UB CL-851-VTC 22 506-B* CL-610-HVTC 30
GLBU1-AW-HW* CL-101-HVTC 29 205-UL CL-253-HTC 4 247109 CL-1213-TW 82 506-LB* CL-611-HVTC 31
GLBU3* CL-311-HVTC 31 205-UR CL-252-HTC 4 247110 CL-113000-BR 82 507107 CL-51610-TW 82
GLBU3-AW-HW* CL-301-HVTC 29 205-USS CL-250-HTC-S 4 250* CL-800-VTC 25 507206* CL-516212-SF 82
GLBU5* CL-511-HVTC 31 205105 CL-142000-BR 82 250-G CL-800-VTC 25 507208 CL-516212-FC 79
GLBU5-AW-HW* CL-501-HVTC 29 205203 CL-14112-SA 78 250121* CL-113000-BR 82 507907 CL-51610-TW-S 81
GLBU6* CL-611-HVTC 31 205943* CL-83234-SA-S 78 250203 CL-58438-SA 78 509208 CL-516212-CC 79
GLBU6-AW-HW* CL-601-HVTC 29 206-HSS* CL-51-TC 5 250206* CL-44-SSC 81 527208 CL-38314-FC 79
GU1* CL-120-HVTC 30 206-SS* CL-51-TC 5 258* CL-801-VTC 25 548* CL-501-HVTC 29
GU1-B* CL-110-HVTC 30 207-L CL-353-VTC 18 258-G CL-801-VTC 25 578* CL-601-HVTC 29
GU3* CL-320-HVTC 30 207-LB* CL-351-VTC 18 267 CL-950-VTC 24 588* CL-601-HVTC 29
GU3-B* CL-310-HVTC 31 207-LR* CL-350-LVTC 18 267-U CL-1050-VTC 24 6001-M CLM-60-SPC 42
GU5* CL-520-HVTC 30 207-S CL-350-VTC 18 267102 CL-5811-TW 81 6001-MMS* CLM-60-SPC 42
GU5-B* CL-510-HVTC 30 207-SB CL-351-VTC 18 301 CL-150-PA 63 601* CL-50-SPC 42
GU6* CL-620-HVTC 30 207-TL* CL-352-VTC 18 301-SS CL-150-PA-S 63 601-0* CL-51-SPC 42
GU6-B* CL-610-HVTC 30 207-TS CL-352-VTC 18 305-U CL-200-VTC 15 601-M* CLM-50-SPC 42
H-100 CL-250-HTC 4 207-TU CL-452-VTC 18 305-UR* CL-200-LVTC 15 601-SS* CL-50-SPC-S 42
H-200 CL-350-HTC 6 207-TUL* CL-452-VTC 18 305-USS CL-200-VTC-S 15 6015 CL-100-SPC 43
H-200(SS) CL-350-HTC-S 6 207-U CL-450-VTC 18 305203* CL-316112-SA 78 6015-M CLM-100-SPC 43
H-400* CL-450-HTC 7 207-UB CL-451-VTC 18 305208 CL-316112-CC 79 6015-MR CLM-100-LSPC 43
H-400(B) CL-450-HTC 7 207-UL CL-453-VTC 18 307-U CL-300-VTC 32 6015-MRSS* CL-100-LSPC-S 43
H-400(SS)* CL-450-HTC-S 7 207-ULB* CL-451-VTC 18 307-UR* CL-300-LVTC 32 6015-R CL-100-LSPC 43
H-600 CL-550-HTC 7 207-UR* CL-450-LVTC 18 307-USS CL-300-VTC-S 32 6015-RSS CL-100-LSPC-S 43
H-600(SS) CL-550-HTC-S 7 207105 CL-518000-BR 82 309-U CL-500-VTC 32 6015-SS CL-100-SPC-S 43
LUP-1203 CL-450-PL 67 207203 CL-516212-SA 78 309-UR* CL-500-LVTC 32 602 CL-150-TPC 49
LUP-800 CL-254-PL 66 207206 CL-14200-SF 81 309-USS CL-500-VTC-S 32 602-M CLM-150-TPC 49
LUP-800-2S CL-254-PL-2 66 207943* CL-516212-SA-S 78 311 CL-170-PA 73 602-SS CL-150-TPC-S 49
P-1200 CL-250-PL 66 210-S CL-550-VTC 20 317 CL-375-HTC 12 603* CL-100-PC 50
P-1203 CL-450-PL 67 210-SB CL-551-VTC 20 317-U CL-475-HTC 12 603-M* CLM-100-PC 50
P-400* CL-50-PL 65 210-SR* CL-550-LVTC 20 323* CL-100-PA 58 603-MR CL-100-LPC 50
P-400-1* CL-50-PL 65 210-TS CL-552-VTC 20 323-MSS* CL-100-PA-S 58 603-R* CL-100-LPC 50
P-400-2* CL-50-PL-2 65 210-TU CL-652-VTC 20 323-SS CL-100-PA-S 58 604 CL-250-TPC 49
P-400-2S* CL-50-PL-3 65 210-U CL-650-VTC 20 324* CL-110-PA 62 604-M CLM-250-TPC 49
P-800 CL-254-PL 66 210-UB CL-651-VTC 20 324-SS* CL-110-PA-S 62 604-SS CL-250-TPC-S 52
P-800-2S CL-254-PL-2 66 210-UR* CL-650-LVTC 20 325 CL-325-PL-S 68 604106 CL-250-TPCA 52
PCH-101 CL-250-PA 57 210-USS CL-650-VTC-S 20 325-SS CL-325-PL-S 68 605 CL-150-SPC 44
PCH-101(SS) CL-250-PA-S 57 210114 CL-316000-BR 81 325203* CL-12314-SA 78 605-M CLM-150-SPC 44
PCH-200 CL-250-PA 57 210203* CL-38314-SA 78 331* CL-200-PA 58 607* CL-350-SPC 45
PH & PL-1600 CL-250-PL 66 210206 CL-38314-SF 80 331-R* CL-200-LPA 60 608 CL-200-PC 50
S-100 CL-251-VTC 16 210208 CL-38314-CC 79 331-R-SS* CL-200-LPA-S 60 610* CL-250-SPC 46
S-200* CL-451-VTC 18 211208* CL-14200-CC 79 331-SS* CL-200-PA-S 58 610-M* CLM-250-SPC 46
S-400* CL-651-VTC 13 213-U* CL-260-HTC 5 334* CL-210-PA 62 620* CL-275-SPC 49
T-100 CL-252-VTC 16 213-USS* CL-260-HTC-S 5 334-SS* CL-210-PA-S 62 620-M* CLM-275-SPC 49
T-200 CL-452-VTC 18 213208 CL-14200-CC 79 341* CL-300-PA 58 624 CL-350-TPC 52
T-400 CL-652-VTC 20 213943 CL-832203-SA-S 78 341-R* CL-300-LPA 60 624-M CLM-350-TPC 52
V-100 CL-250-VTC 16 215-S CL-300-HTC 6 341-R-SS* CL-300-LPA-S 60 624-SS CL-350-TPC-S 52
V-100(SS) CL-250-VTC-S 16 215-U CL-350-HTC 6 341-SS* CL-300-PA-S 58 628* CL-276-SPC 49
V-1200* CL-1050-VTC 24 215-UB CL-351-HTC 6 344* CL-310-PA 62 630 CL-350-SPC 45
V-200* CL-453-VTC 18 215-USS CL-350-HTC-S 6 344-SS* CL-310-PA-S 62 630-M CLM-350-SPC 45
V-200(SS)* CL-450-VTC-S 18 215105* CL-148-TW 82 345 CL-345-PL 68 630-MR* CL-350-LPC 45
V-400* CL-650-VTC 20 215208 CL-14200-FC 79 345100 CL-345-PLA 68 630-M CL-350-LPC 45
V-400(SS)* CL-650-VTC-S 20 215905* CL-148-TW-S 82 351 CL-250-PA 57 640* CL-450-SPC 47
VC-200* CL-350-VTC 18 217-U* CL-350-HTC 6 351-B CL-251-PA 57 640-M* CLM-450-SPC 47
VC-400* CL-550-VTC 20 217-USS* CL-350-HTC-S 6 351-R* CL-257-PA 57 650 CL-650-SPC 47
102111 CL-3166-TW 82 220 CL-600-VTC 25 351-SS CL-250-PA-S 57 650-M CLM-650-SPC 47
102208 CL-832208-FC 82 220203 CL-12314-SA 78 375 CL-400-PA 59 7-59 CL-1000-VCC 26
102911 CL-3166-TW-S 82 220208* CL-38314-CC 79 375-R CL-400-LPA 61 802* CL-500-PTC 70
105106 CL-832-TW 82 225-U CL-450-HTC 7 381 CL-350-PA 57 803* CL-1500-PPC 76
105203 CL-832203-SA 73 225-UB CL-451-HTC 7 385 CL-500-PA 59 807-L* CL-1001-PTC 72
105208* CL-832208-FC 79 225-UR* CL-451-HTC 7 385-R CL-500-LPA 61 807-LH/T* CL-1001-PTCH 72
105906 CL-832-TW-S 82 225-USS CL-450-HTC-S 7 385102 CL-500-PAA 59 807-UL* CL-1000-PTC 72
110122 CL-511000-BR 82 225208 CL-518208-FC 79 424 CL-50-PL 65 807-ULH/T* CL-1000-PTCH 72
201 CL-150-VTC 15 227-U* CL-450-HTC 7 424-2 CL-50-PL-2 65 810-S* CL-2001-PTC 73
201-B CL-151-VTC 15 227-USS* CL-450-HTC-S 7 424208 CL-14208-SA 78 810-U* CL-2000-PTC 73
201-SS CL-150-VTC-S 15 227943* CL-516212-SA-S 78 431208 CL-14100-SA 78 812* CL-400-PTC 70
201-T CL-152-VTC 15 228 CL-601-VTC 25 441 CL-150-PL 65 816* CL-600-PPC 75
201208 CL-316112-FC 79 235-U CL-550-HTC 7 441203* CL-516212-SA 76 847-S* CL-2001-PTC 73
201943 CL-316100-SA-S 78 235-UB CL-551-HTC 7 462 CL-254-PL 66 847-U* CL-2000-PTC 73
202 CL-250-VTC 16 235-UR* CL-550-HTC 7 462-2 CL-254-PL-2 66 858* CL-3000-PTC 74
202-B CL-251-VTC 16 235-USS CL-550-HTC-S 7 463 CL-454-PL 66 870* CL-1011-POC 77
202-SS CL-250-VTC-S 16 235106 CL-3811-TW 82 468 CL-254-PL 66 871* CL-1010-POC 77
202-T CL-252-VTC 16 235906 CL-3811-TW-S 82 468206* CL-38314-SF 81 902* CL-516212-SL 81
202-U* CL-253-VTC 16 237-U* CL-550-HTC 7 474 CL-454-PL 67 904* CL-38314-SL 81
202-USS CL-253-VTC-S 16 237-USS* CL-550-HTC-S 7 486* CL-550-PL 65
202203* CL-14200-SA 78 237943* CL-38314-SA-S 78 501* CL-120-HVTC 30
202208 CL-14112-FC 79 240203* CL-38314-SA 78 501-B* CL-110-HVTC 30
* Functionally equivalent, but differs in some dimension and/or specification. Please check catalog before ordering.

2TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

Sizes marked * are also available

in stainless steel.

All Carr Lane toggle clamps are DFARS and RoHS compliant.

Standard HTC Design

pp. 4-9
Most-popular and widest-range series of
100 lbs* 200 lbs* 750 lbs* horizontal-handle hold-down clamps.
Available in seven sizes, the smaller
ones with a comfortable finger grip. Most
sizes are available with either a flanged
base or a straight base. Choice of solid
60 lbs* 150 lbs* 500 lbs* 1000 lbs arm, or open arm for spindle adjustment.

Automatically Adjusting
p. 10
Self-adjusting clamp automatically
compensates for different workpiece heights
without resetting the spindle. Clamping
750 lbs force is always consistent after setting once.

Low-Arm TC Design
p. 11
Simple, classic-design horizontal-handle
clamps. Available in three sizes, with
250 lbs 625 lbs 850 lbs either a flanged base or a straight base.

Extra-Wide Opening
p. 12
Arm opens a full 185° for maximum
loading clearance. Unique up-then-down
handle motion. Handle locks at a 60°
downward angle. Dual flanged bases
allow mounting on either horizontal or
375 lbs vertical surfaces. Choice of solid arm, or
open arm for spindle adjustment.

(Rev. 3/08) 3TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

Solid Arm

Open Arm

60 lbs

CL-150-HTC Solid Arm, Flanged Base

CL-250-HTC Open Arm, Flanged Base

Smallest hold-down clamp available. Choose either a solid
arm, or an open arm for spindle adjustment. Arm opens 90°
while handle moves 80°. Supplied with #8-32 nylon hex-head
spindle CL-832203-SA. Open-arm versions also include (2)
CL-832-TW flanged washers. Shipping weight 0.1 lbs.

Holding capacity: 60 lbs

Also available in
CL-151-HTC CL-152-HTC CL-153-HTC stainless steel . . .
Solid Arm Solid Arm Solid Arm
Straight Base Right Flange Left Flange

CL-150-HTC-S

CL-251-HTC CL-252-HTC CL-253-HTC

Open Arm Open Arm Open Arm
Straight Base Right Flange Left Flange CL-250-HTC-S

4TC (Rev. 10-07)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

5/8

5/32 7/16
5/8
15/16
CL-52-TC (4) SLOTS 11/64 X 17/64
13/16 FOR #8 OR M4 SCREWS
Low Arm Low Arm, Straight Base 1/2
21/64
5/8 15/16
3/16 7/32
7/16 23/32
5/32 5/8
1-1/8 15/16

High Arm #8-32 STAINLESS

5/32 7/16 HEX-HEAD SPINDLE VINYL GRIP
5/8
100 lbs 15/16 2-1/8
Stainless Steel
CL-54-TC 5/32
High Arm, Straight Base 1-1/8
19/32
CL-51-TC Low Arm, Flanged Base
3/64 15/32 19/32
CL-53-TC High Arm, Flanged Base
Miniature stainless steel clamp with open arm for
LOW ARM 1-1/16 13/64
2-25/32
spindle adjustment. Perfect for electronics fixturing and
other light-duty application. Arm opens 90˚ while handle 15/16
moves 90˚. Supplied with #8-32 stainless hex-head HIGH ARM
spindle CL-832203-SA-S. Shipping weight 0.1 lbs.
Holding capacity: 100 lbs

150 lbs

CL-260-HTC
An extremely powerful clamp for its small size. Also available in stainless steel . . .
Open arm allows spindle adjustment. Arm opens
90° while handle moves 75°. Supplied with #10-32
flat-cushion spindle CL-316112-FC and (2) CL-
3166-TW flanged washers. Shipping weight 0.2 lbs.
Holding capacity: 150 lbs
CL-260-HTC-S

(Rev. 2/05) 5TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

Solid Arm

Open Arm

200 lbs

CL-300-HTC Solid Arm, Flanged Base

CL-350-HTC Open Arm, Flanged Base
Popular medium-duty clamp. Choose either a solid arm, or
an open arm for spindle adjustment. Arm opens 86˚ while
handle moves 60˚. Supplied with 1/4-20 short flat-cushion
spindle CL-14112-FC. Solid-arm version supplied with
CL-142000-BR bolt retainer. Open-arm version supplied
with (2) CL-147-TW flanged washers. Shipping weight
0.3 lbs.

Holding capacity: 200 lbs

Also available in stainless steel . . .

CL-351-HTC
Open Arm
Straight Base
CL-350-HTC-S

(Rev. 10-07)
6TC
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

500 lbs CL-451-HTC

Straight Base

CL-450-HTC Flanged Base Also available in stainless steel . . .

Strong-yet-compact horizontal-handle clamp, with open
arm for spindle adjustment. Arm opens 90° while handle
moves 65°. Supplied with 5/16-18 short flat-cushion
spindle CL-518208-FC and (2) CL-51610-TW flanged
washers. Shipping weight 0.6 lbs.
Holding capacity: 500 lbs CL-450-HTC-S

O H
W ALS LE WIT !
NO AILAB LOCK
AV FETY
SA Press lever to unlock.

500 lbs

CL-450-LHTC Flanged Base

with Safety Lock
Same as the toggle clamp shown above, except with our
new safety-lock feature. This safety lock automatically
engages when the clamp is closed, then remains locked
until manually disengaged by pressing the lever before
opening. This prevents the clamp from being accidentally
opened by bumping the handle. Shipping weight 0.7 lbs.
Holding capacity: 500 lbs

(Rev. 11/07) 7TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

750 lbs
CL-551-HTC
Straight Base

CL-550-HTC Flanged Base Also available in stainless steel . . .

Heavy-duty clamp with open arm for spindle adjustment.
Arm opens 90° while handle moves 55°. Supplied with
3/8-16 short flat-cushion spindle CL-38212-FC and (2)
CL-3811-TW flanged washers. Shipping weight 1.5 lbs.

Holding capacity: 750 lbs CL-550-HTC-S CL-551-HTC-S

O H
W ALS LE WIT !
O B
N AILA LOCK
AV FETY
SA Press lever to unlock.

750 lbs

Flanged Base
CL-550-LHTC with Safety Lock
Same as the toggle clamp shown above, except with our
new safety-lock feature. This safety lock automatically
engages when the clamp is closed, then remains locked
until manually disengaged by pressing the lever before
opening. This prevents the clamp from being accidentally
opened by bumping the handle. Shipping weight 1.6 lbs.
Holding capacity: 750 lbs

8TC (Rev. 10/08)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

9/16
BOLT RETAINER
3/8 CL-113000-BR
1/8

7/8

Solid Arm 1-5/8

Open Arm

1000 lbs

CL-600-HTC Solid Arm

CL-650-HTC Open Arm

Largest and strongest horizontal-handle hold-down clamp.
Choose either a solid arm, or an open arm for spindle
adjustment. Arm opens a wide 105˚ while handle moves
75˚. Supplied with 1/2-13 hex-head spindle CL-12314-SA.
Solid-arm version supplied with a CL-113000-BR bolt
retainer. Open-arm version supplied with (2) CL-1213-TW
flanged washers. Shipping weight 3.3 lbs.

Holding capacity: 1000 lbs

(Rev. 10/07) 9TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

750 lbs
Automatic Toggle Clamp
(Self Adjusting)

CL-550-AHTC
Automatic Toggle Clamp
Automatically adjusts for different workpiece
thicknessess! Clamps with the same, repeatable force
anywhere within its 1/2" automatic-adjustment range.
Perfect for welding fixtures, machining fixtures for
castings, fixtures holding several part sizes within the
same family, or any other application where part size
can vary.
Easy to use. To set up, simply adjust the contact
spindle to the average workpiece height, and set
desired clamping force once. After that, operate just like
a standard toggle clamp. The patented adjusting
mechanism does the rest.
Clamping force is always consistent. The clamp’s
toggle action ensures that workpieces will remain
clamped even under severe vibration. No additional
spindle adjustment is ever needed. The clamp even
compensates for wear in long production runs.
Fits in the same space, and provides the same
clamping force as a standard toggle clamp. A maximum
of 250 to 500 lbs clamping force (depending on spindle
position) can be applied by hand. Arm opens 87° while
handle moves 80°. Supplied with 3/8-16 radius spindle
CL-38200-RS and (2) CL-3811-TW flanged washers.
Patent no. 4,407,493. Other patents pending. Shipping
weight 1.9 lbs.

Holding capacity: 750 lbs

Low Limit HIgh Limit

–1/4" +1/4"

10TC (Rev. 8/98)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
HORIZONTAL HANDLE

850 lbs
625 lbs
250 lbs

Classic-design horizontal-handle clamps with open arm for

spindle adjustment. Arm opens 90° while handle moves 90°.
Available in three sizes.

CL-151-TC Flanged Base

Smallest-size clamp. Accepts any #10-32 spindle and (2) CL-
3166-TW flanged washers. For fixed spindle location, use a
1/4-20 spindle and a CL-1458-S bolt retainer. See pages 78-
82 to order. Shipping weight 0.4 lbs.
Holding capacity: 250 lbs

CL-251-TC Flanged Base

Medium-size clamp. Accepts any 1/4-20 spindle and (2) CL-148-
TW flanged washers. For fixed spindle location, use a CL-1458-S
bolt retainer. See pages 78-82 to order. Shipping weight 0.5 lbs.
Holding capacity: 625 lbs

CL-351-TC Flanged Base

Largest-size clamp. Accepts any 5/16-18 spindle and (2) CL-
51610-TW flanged washers. For fixed spindle location, use a CL-151-TC (Top dimension)
CL-51658-S bolt retainer. See pages 78-82 to order. Shipping
weight 1.4 lbs. CL-251-TC (Middle dimension)
CL-351-TC (Bottom dimension)
Holding capacity: 850 lbs

CL-152-TC CL-252-TC
Straight Base Straight Base
250 lbs 625 lbs

(Rev. 11/09) 11TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

HORIZONTAL HANDLE

Open Arm

Solid Arm

375 lbs

CL-375-HTC Solid Arm

CL-475-HTC Open Arm

Extra-wide-opening clamp with handle that locks at a
downward angle. Unique up-then-down handle motion
opens arm a full 185°. Dual flanged bases allow mounting
on either horizontal or vertical surfaces. Available with a
solid arm, or an open arm for spindle adjustment. Accepts
all 5/16-18 spindles . . . see pages 78-81 to order. Solid-
arm version supplied with a CL-518000-BR bolt retainer.
Open-arm version supplied with (2) CL-51610-TW flanged
washers. Shipping weight 0.8 lbs.

Holding capacity: 375 lbs

Unique up-then-down handle action

12TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

Sizes marked * are also available

in stainless steel

All Carr Lane toggle clamps are DFARS and RoHS compliant.

Wide Opening
pp. 15-24
Clamping arm opens past 90° for excellent
loading clearance. Most-popular and
widest-range series of vertical-handle hold-
down clamps. Choice of flanged or straight
base, solid or open arm, and regular or T
100 lbs* 200 lbs* 500 lbs* 750 lbs* 1000 lbs 1200 lbs handle in most of the seven available sizes.

Wide Opening – Angle Arm

p. 25
Clamps with arm tilted upward for
increased clearance underneath. Also
useful for applying clamping force at an
angle. Wide-opening solid arm. Choice of
flanged base or straight base. Available in
750 lbs 1000 lbs two sizes.

Wide Opening
Automatically Adjusting
p. 27
Self-adjusting clamp automatically
compensates for different workpiece
heights without resetting the spindle.
Clamping force is always consistent. Wide
750 lbs opening.

Wide Opening – Heavy-Duty

pp. 28-31
Heavy-duty production clamps designed for
extreme durability. Available either as
complete clamps or as basic mechanisms
for adding custom clamping arms or
handles. Choice of four sizes.
750 lbs 2000 lbs 3000 lbs 6000 lbs
CONTINUED ON NEXT PAGE

(Rev. 11/09) 13TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

VERTICAL HANDLE
CONTINUED FROM PREVIOUS PAGE

Low Profile
pp. 32-33
Extremely compact low-profile clamps with
a unique finger-grip T handle. Available in
three sizes.
150 lbs* 350 lbs* 750 lbs*

Low Arm
100 lbs* 250 lbs 625 lbs 850 lbs pp. 34-35, 38
Simple, easy-opening clamps with excellent
arm reach. Extends farther over workpiece
than any clamp its size. Choice of flanged
or straight base, and solid or open arm.
Arm opens 83°. Available in six sizes, the
largest two forged.

1500 lbs 2500 lbs 5000 lbs

100 lbs* 250 lb 625 lbs 850 lbs

High Arm
pp. 36-37, 39
Simple, easy-opening clamps with extra
arm height. Choice of flanged or straight
base, and solid or open arm. Arm opens
83°. Available in six sizes, the largest two
forged.

1500 lbs 2500 lbs 5000 lbs

Vertical Handle
Cam Clamps
p. 26
Wide-opening clamp that locks by spiral-
cam action rather than toggle action. Solid
arm, flanged base.

1000 lbs

14TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

100 lbs

CL-150-VTC Flanged Base

Smallest wide-opening hold-down clamp available. Open
arm provides adjustable spindle location. Arm opens 100°
while handle moves 56°. Supplied with #10-32 flat-
cushion spindle CL-316112-FC and (2) CL-3166-TW
flanged washers. Shipping weight 0.2 lbs.
Also available
Holding capacity: 100 lbs in stainless steel...

CL-150-VTC-S

Also available
air powered...

CL-151-VTC CL-152-VTC
Straight Base Flanged Base
T Handle
CL-400-PTC
(page 70)

(Rev. 11/09) 15TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

Solid Arm
Long Open Arm

200 lbs

CL-250-VTC Solid Arm, Flanged Base

CL-253-VTC Long Open Arm, Flanged Base

Small-yet-powerful clamp available in several configurations.
Choose either a solid arm, or a long open arm for spindle
adjustment. Arm opens 117° while handle moves 69°.
Supplied with 1/4-20 short flat-cushion spindle CL-14112-FC.
Open-arm version supplied with (2) CL-148-TW flanged
washers. Shipping weight 0.4 lbs.

Holding capacity: 200 lbs

Also available in stainless steel . . .

CL-250-VTC-S CL-253-VTC-S

Also available air powered . . .

CL-251-VTC CL-252-VTC
Solid Arm Solid Arm
Straight Base Flanged Base CL-500-PTC
T Handle (page 71)

16TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH-PULL

O
W ALS E WITH
NO LABL K!
I
AVA TY LOC
E
SAF

Solid Arm

Long Open Arm

200 lbs

CL-250-LVTC Solid Arm, Flanged Base

CL-253-LVTC Long Open Arm, Flanged Base

Same as the wide-opening toggle clamps shown on opposite
page 16, except with our new safety-lock feature. This safety
lock automatically engages when the clamp is closed, then
remains locked until manually disengaged by pressing the
handle. This prevents the clamp from being accidentally
opened by bumping the handle.

Choose either a solid arm, or a long open arm for spindle

adjustment. Arm opens 117º while handle moves 69º.
Supplied with 1/4-20 short flat-cushion spindle CL-14112-FC.
Open-arm version supplied with (2) CL-148-TW flanged
washers. Shipping weight 0.4 lbs.

Holding capacity: 200 lbs

Also available in stainless steel . . .

! !
NEW NEW

Press Lever To Unlock CL-250-LVTC-S CL-253-LVTC-S

(Rev. 7/10) 17TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

Solid Arm Open Arm

500 lbs

CL-350-VTC Solid Arm, Flanged Base

CL-450-VTC Open Arm, Flanged Base

Most-popular wide-opening clamp available in many
configurations. Choose either a solid arm, or an open arm for
spindle adjustment (extra-long arms also available). Arm opens
100° while handle moves 60°. Accepts any 5/16-18 short
spindle . . . see pages 78-81 to order. Solid-arm versions
supplied with a CL-518000-BR bolt retainer. Open-arm
versions supplied with (2) CL-51610-TW flanged washers.
Shipping weight 0.8 lbs.
Holding capacity: 500 lbs
Also available
in stainless steel . . .

CL-450-VTC-S
CL-351-VTC CL-352-VTC CL-353-VTC
Solid Arm Solid Arm Long Solid Arm
Straight Base Flanged Base Flanged Base Also available
T Handle air powered . . .

CL-1001-PTC
Solid Arm
(page 72)

CL-451-VTC CL-452-VTC CL-453-VTC

Open Arm Open Arm Long Open Arm
Straight Base Flanged Base Flanged Base CL-1000-PTC
T Handle Open Arm
(page 72)

18TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

O
W ALS E WITH
NO LABL K!
I
AVA TY LOC
E
SAF

Solid Arm

Open Arm

500 lbs

CL-350-LVTC Solid Arm, Flanged Base

CL-450-LVTC Open Arm, Flanged Base

Same as the wide-opening toggle clamps shown on opposite

page 18, except with our new safety-lock feature. This safety
lock automatically engages when the clamp is closed, then
remains locked until manually disengaged by pressing the
handle. This prevents the clamp from being accidentally opened
by bumping the handle.

Choose either a solid arm, or an open arm for spindle

adjustment. Arm opens 100° while handle moves 60°. Accepts
any 5/16-18 short spindle . . . see pages 78-81 to order. Solid-
arm version supplied with CL-518000-BR bolt retainer. Open-
arm version supplied with (2) CL-51610-TW flanged washers.
Shipping weight 0.9 lbs.

Holding capacity: 500 lbs

Also available
in stainless steel . . .
NEW!

Press Lever To Unlock CL-450-LVTC-S

(Rev. 7/10) 19TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

Solid Arm Open Arm

750 lbs

CL-550-VTC Solid Arm, Flanged Base

CL-650-VTC Open Arm, Flanged Base

Larger wide-opening clamp available in several configurations.
Choose either a solid arm, or an open arm for spindle
adjustment. Arm opens 106° while handle moves 58°. Accepts
any 3/8-16 spindle . . . see pages 78-81 to order. Solid-arm
version supplied with a CL-316000-BR bolt retainer. Open-arm
version supplied with (2) CL-3811-TW flanged washers.
Shipping weight 1.3 lbs.
Holding capacity: 750 lbs

Also available with

CL-551-VTC CL-552-VTC patented automatic adjustment!
Solid Arm Solid Arm
Straight Base Flanged Base
T Handle

CL-650-ATC
(page 27)
Also available in stainless steel . . .

CL-652-VTC
CL-651-VTC Open Arm
Open Arm Flanged Base
Straight Base T Handle
CL-650-VTC-S

20TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

O
W ALS E WITH
NO LABL K!
I
AVA TY LOC
E
SAF

Solid Arm

Open Arm

750 lbs

CL-550-LVTC Solid Arm, Flanged Base

CL-650-LVTC Open Arm, Flanged Base

Same as the wide-opening toggle clamps shown on opposite

page 20, except with our new safety-lock feature. This safety
lock automatically engages when the clamp is closed, then
remains locked until manually disengaged by pressing the
handle. This prevents the clamp from being accidentally opened
by bumping the handle.

Choose either a solid arm, or an open arm for spindle

adjustment. Arm opens 106° while handle moves 58°. Accepts
any 3/8-16 spindle . . . see pages 78-81 to order. Solid-arm
version supplied with CL-316000-BR bolt retainer. Open-arm
version supplied with (2) CL-3811-TW flanged washers.
Shipping weight 1.4 lbs.

Holding capacity: 750 lbs

Press Lever To Unlock

(Rev. 11/09) 21TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

VERTICAL HANDLE

Solid Arm

Open Arm

1000 lbs

CL-750-VTC Solid Arm, Flanged Base

CL-850-VTC Open Arm, Flanged Base

Extra-large wide-opening clamp. Choose either a solid arm, or

an open arm for spindle adjustment. Arm opens 120˚ while han-
dle moves 67˚. Accepts any 1/2-13 spindle . . . see pages 78-81
to order. Solid-arm version supplied with a CL-113000-BR bolt
retainer. Open-arm version supplied with (2) CL-1213-TW
flanged washers. Shipping weight 2.5 lbs.

Holding capacity: 1000 lbs

Also available air powered . . .

CL-2001-PTC
Solid Arm
(page 73)

CL-751-VTC CL-851-VTC
Solid Arm Open Arm CL-2000-PTC
Straight Base Straight Base Open Arm
(page 73)

22TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

O
W ALS E WITH
NO LABL K!
I
AVA TY LOC
E
SAF

Solid Arm

Open Arm

1000 lbs

CL-750-LVTC Solid Arm, Flanged Base

CL-850-LVTC Open Arm, Flanged Base

Same as the wide-opening toggle clamps shown on opposite

page 22, except with our new safety-lock feature. This safety
lock automatically engages when the clamp is closed, then
remains locked until manually disengaged by pressing the
handle. This prevents the clamp from being accidentally opened
by bumping the handle.

Choose either a solid arm, or an open arm for spindle

adjustment. Arm opens 120° while handle moves 67°. Accepts
any 1/2-13 spindle . . . see pages 78-81 to order. Solid-arm
version supplied with CL-113000-BR bolt retainer. Open-arm
version supplied with (2) CL-1213-TW flanged washers.
Shipping weight 2.5 lbs.

Holding capacity: 1000 lbs

Press Lever To Unlock

(Rev. 11/09) 23TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

Solid Arm Open Arm

1200 lbs

CL-950-VTC Solid Arm

CL-1050-VTC Open Arm

Largest wide-opening clamp available. Choose either a solid

arm, or an open arm for spindle adjustment. Arm opens 140°
while handle moves 70°. Accepts any 5/8-11 spindle . . . see
pages 78-81 to order. Solid-arm version supplied with a
CL-511000-BR bolt retainer. Open-arm version supplied with (2)
CL-5811-TW flanged washers. Shipping weight 5.2 lbs.

Holding capacity: 1200 lbs

24TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

750 lbs
Angled Arm
CL-601-VTC
Straight Base
BRACKET INCLUDED
with Bracket
WITH CL-601-VTC

CL-600-VTC Flanged Base

Angled-arm clamp provides increased clearance under-
neath arm. Also useful for applying clamping force at an version has a longer handle and includes a separate base
angle. Solid arm opens 113° while handle moves 66°. to allow mounting at any angle. Shipping weight 1.0 to 1.5
Accepts any 3/8-16 spindle . . . see pages 78-81 to order. lbs.
Supplied with a CL-316000-BR bolt retainer. Straight-base Holding capacity: 750 lbs

1000 lbs
Angled Arm CL-801-VTC
Straight Base
with Bracket

CL-800-VTC Flanged Base

Larger-size angled-arm clamp. Solid arm opens 126° while
handle moves 76°. Accepts any 5/8-11 spindle. . .see BRACKET INCLUDED
pages 78-81 to order. Supplied with a CL-511000-BR bolt WITH CL-801-VTC
retainer. Straight-base version includes a separate base to
allow mounting at any angle. Shipping weight 2.5 to 2.8 lbs.
Holding capacity: 1000 lbs

(Rev. 11/09) 25TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

1000 lbs
Cam Action

CL-1000-VCC
Wide-opening clamp that locks by cam action rather than
toggle action. Smooth spiral cam locks securely anywhere
within a 3/16-inch clamping range. Rugged cast-steel com-
ponents are flame hardened at all wear points. Solid arm
can be tapped to accept a spindle, or otherwise modified.
Shipping weight 2.5 lbs.

Holding capacity: 1000 lbs

Optional Vinyl Grip

CL-3-HVTC-G

Low Limit Average Setting High Limit

26TC (Rev. 11/09

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

750 lbs
Automatic Toggle Clamp
(Self Adjusting)

CL-650-ATC
Automatic Toggle Clamp
Automatically adjusts for different workpiece thicknesses!
Clamps with the same force anywhere within its adjustment
range (1-1/4"). Perfect for welding fixtures, machining fix-
tures for castings, fixtures holding several part sizes within
the same family, or any other application where part size
can vary.
Easy to use. To set up, simply adjust the contact spindle
to the average workpiece height, and set desired clamping
force. After that, operate just like a standard toggle clamp.
The patented adjusting mechanism does the rest.
Clamping force is always consistent. The clamp’s toggle
action ensures that workpieces will remain clamped even
under severe vibration. No additional spindle adjustment is
ever needed. The clamp even compensates for wear in
long production runs.
Fits in the same space, and provides the same clamping
force as a standard toggle clamp. A maximum of 250 to
500 lbs clamping force (depending on spindle position) can
be applied by hand. Arm opens 106° while handle moves
58°. Supplied with 3/8-16 radius spindle CL-38314-RS and
(2) CL-3811-TW flanged washers. Patent no. 4,407,493.
Other patents pending. Shipping weight 1.9 lbs.
Holding capacity: 750 lbs

Low Limit Average Setting High Limit

(Rev. 11/09) 27TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

6000 3000 2000 750

lbs lbs lbs lbs

Complete Clamp
Flanged Base

Heavy-duty automotive-type production clamps designed for extreme durability.

The above configuration includes a long horizontal clamping arm with an
attached bolt retainer, a vertical handle with vinyl grip, and an integral flanged
base (see pages 29-31 for other versions). Precision, close-tolerance steel com-
ponents throughout provide exceptionally smooth operation. Rugged alloy steel
handle fork. Guided-arm feature provides positive lateral arm support. All pivot
pins are hardened and ground, running in either hardened bushings or the close-
tolerance holes of hardened parts. The bottom pivot is a precision bolt which can
be adjusted, if desired, to fine tune the amount of free play. These clamps are
built to withstand abuse. With just occasional lubrication, they will provide
extremely long service life. Black oxide finish. Available in four sizes.

CL-100-HVTC Complete Clamp, Flanged Base

Smallest of the four sizes, yet still quite powerful. Cast alloy steel base and
slotted open clamping arm on this size only. Arm opens 130° while handle
moves 90°. Accepts any 1/4-20 spindle…see pages 78-81 to order.
Supplied with (2) CL-148-TW flanged washers. Shipping weight 1.0 lbs.
Holding capacity: 750 lbs

CL-300-HVTC Complete Clamp, Flanged Base

Solid arm opens 180° while handle moves 120°. Accepts any 1/2-13 spin-
dle…see pages 78-81 to order. Shipping weight 2.8 lbs.
Holding capacity: 2000 lbs

CL-500-HVTC Complete Clamp, Flanged Base

Solid arm opens 180° while handle moves 125°. Accepts any 1/2-13 spin-
dle…see pages 78-81 to order. Shipping weight 4.3 lbs.
Holding capacity: 3000 lbs

CL-600-HVTC Complete Clamp, Flanged Base

Our most-powerful hold-down toggle clamp. Solid arm opens 195° while
handle moves 130°. Accepts any 5/8-11 spindle…see pages 78-81 to
order. Shipping weight 9.1 lbs.
Holding capacity: 6000 lbs
PART NO.
COMPLETE C
CLAMP A B DIA D E F G H J K L M N P Q R1 R2 S1 S2 T U V W X Y
CL-100-HVTC .236 4.45 .50 .197 .26 1.54 .35 .49 .236 .748 1.260 1.22 1.73 1/4 or M6 .55 .59 .59 .98 .98 .59 1.26 1.54 3.31 .51 .87
CL-300-HVTC .394 8.46 .75 .197 .52 1.97 1.57 .75 .394 .984 1.969 1.77 2.64 5/16 or M8 .91 1.18 .87 1.89 1.89 .98 2.13 2.52 4.87 1.10 1.72
CL-500-HVTC .472 9.84 .87 .236 .52 2.36 1.97 .75 .394 1.181 2.362 1.97 3.46 5/16 or M8 .98 1.18 1.02 2.28 2.32 .98 2.40 2.92 5.66 1.42 2.19
CL-600-HVTC .630 11.61 .98 .315 .64 2.95 2.36 1.00 .472 1.575 2.953 2.48 4.13 3/8 or M10 1.38 1.50 1.26 2.76 2.95 1.57 3.31 3.98 7.43 1.81 2.76

28TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

VERTICAL HANDLE

6000 3000 2000 750

lbs lbs lbs lbs

Complete Clamp
Straight Base

Heavy-duty automotive-type production clamps designed for extreme durability.

The above configuration includes a long horizontal clamping arm furnished with a
bolt retainer (not welded on), a vertical handle with vinyl grip, and a straight base for
plate/tongue mounting at any angle (see pages 28, 30, and 31 for other versions).
Precision, close-tolerance steel components throughout provide exceptionally
smooth operation. Rugged alloy steel handle fork. Guided-arm feature provides
positive lateral arm support. All pivot pins are hardened and ground, running in either
hardened bushings or the close-tolerance holes of hardened parts. The bottom pivot
is a precision bolt which can be adjusted, if desired, to fine tune the amount of free
play. These clamps are built to withstand abuse. With just occasional lubrication,
they will provide extremely long service life. Black oxide finish. Available in four
sizes.

CL-101-HVTC Complete Clamp, Straight Base

Smallest of the four sizes, yet still quite powerful. Cast alloy steel slotted
open clamping arm on this size only. Arm opens 205° while handle moves
130°. Accepts any 1/4-20 spindle…see pages 78-81 to order. Supplied with
(2) CL-148-TW flanged washers. Shipping weight 0.9 lbs.
Holding capacity: 750 lbs

CL-301-HVTC Complete Clamp, Straight Base

Solid arm opens 205° while handle moves 130°. Accepts any 1/2-13 spin-
dle…see pages 78-81 to order. Shipping weight 2.5 lbs.
Holding capacity: 2000 lbs

CL-501-HVTC Complete Clamp, Straight Base

Solid arm opens 195° while handle moves 130°. Accepts any 1/2-13 spin-
dle…see pages 78-81 to order. Shipping weight 4.0 lbs.
Holding capacity: 3000 lbs Base Plate
(order separately)
CL-601-HVTC Complete Clamp, Straight Base CL-1-HVTC-P (750 lbs)
CL-3-HVTC-P (2000 lbs)
Our most-powerful hold-down toggle clamp. Solid arm opens 195° while han-
CL-5-HVTC-P (3000 lbs)
dle moves 130°. Accepts any 5/8-11 spindle…see pages 78-81 to order.
Shipping weight 8.3 lbs. CL-6-HVTC-P (6000 lbs)
Holding capacity: 6000 lbs
PART NO.
COMPLETE C
CLAMP A B DIA D E F G H J K L M1 M2 N1 N2 P Q R1 R2 S1 S2 T U V W X Y Z
CL-101-HVTC .236 5.08 .50 .118 .26 1.54 .35 .49 .236 .748 1.260 1.06 1.10 .79 1.73 #10 or M5 .55 .59 .59 1.61 1.61 .59 1.26 1.54 3.31 1.14 1.50 .236
CL-301-HVTC .394 9.25 .75 .197 .52 1.97 1.57 .75 .295 .984 1.378 1.77 1.57 1.26 1.97 1/4 or M6 .91 1.18 .87 2.76 2.76 .98 2.13 2.52 4.87 1.97 2.59 .315
CL-501-HVTC .472 10.87 .87 .236 .52 2.36 1.97 .75 .394 1.181 1.575 1.97 1.97 1.50 2.36 5/16 or M8 .98 1.18 1.02 3.35 3.39 .98 2.40 2.92 5.66 2.48 3.25 .315
CL-601-HVTC .630 12.60 .98 .315 .64 2.95 2.36 1.00 .394 1.772 1.969 2.48 2.56 1.97 2.76 5/16 or M8 1.38 1.50 1.26 3.94 4.13 1.57 3.31 3.98 7.43 2.99 3.94 .315

(Rev. 11/09) 29TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

6000 3000 2000 750

lbs lbs lbs lbs

Basic Mechanism
Pivot Base

Heavy-duty automotive-type production clamps designed for extreme durability.

The above configuration is a basic toggle mechanism onto which an arm and han-
dle can be welded at any desired angle (see pages 28, 29, and 31 for other ver-
sions). The pivot base must be welded to both the clamp mechanism and the fix-
ture, or the optional base plate, after setting the clamp at the proper angle. Weld clamp mechanism
Precision, close-tolerance steel components throughout provide exceptionally to pivot base at any
smooth operation. Rugged alloy steel handle fork. Guided-arm feature provides desired angle.
positive lateral arm support. All pivot pins are hardened and ground, running in
either hardened bushings or the close-tolerance holes of hardened parts. The bot-
tom pivot is a precision bolt which can be adjusted, if desired, to fine tune the
amount of free play. These clamps are built to withstand abuse. With just occa-
sional lubrication, they will provide extremely long service life. Black oxide finish.
Available in four sizes.

CL-110-HVTC Basic Mechanism, Pivot Base

Smallest of the four sizes, yet still quite powerful. Arm opens 205° while han-
dle moves 130°. Shipping weight 0.6 lbs. To order basic mechanism without
the pivot base, specify part no. CL-120-HVTC. Clamping Arm Base Plate
Holding capacity: 750 lbs (order separately) (order separately)

CL-310-HVTC Basic Mechanism, Pivot Base

Arm opens 205° while handle moves 130°. Shipping weight 1.6 lbs. To order
basic mechanism without the pivot base, specify part no. CL-320-HVTC.
Holding capacity: 2000 lbs

CL-510-HVTC Basic Mechanism, Pivot Base

Handle Vinyl Grip
Arm opens 195° while handle moves 130°. Shipping weight 2.9 lbs. To order (order separately) (order separately)
basic mechanism without the pivot base, specify part no. CL-520-HVTC.
Holding capacity: 3000 lbs ACCESSORIES
PART NO. PART NO. PART NO.
CL-610-HVTC Basic Mechanism, Pivot Base CLAMP
SIZE
CLAMPING
ARM
BASE
PLATE
PART NO.
HANDLE
VINYL
GRIP
Our most-powerful hold-down toggle clamp. Arm opens 195° while handle 750 lbs CL-1-HVTC-A CL-1-HVTC-P CL-1-HVTC-H CL-1-HVTC-G
moves 130°. Shipping weight 6.4 lbs. To order basic mechanism without the 2000 lbs CL-3-HVTC-A CL-3-HVTC-P CL-3-HVTC-H CL-3-HVTC-G
pivot base, specify part no. CL-620-HVTC. 3000 lbs CL-5-HVTC-A CL-5-HVTC-P CL-5-HVTC-H CL-5-HVTC-G
6000 lbs CL-6-HVTC-A CL-6-HVTC-P CL-6-HVTC-H CL-6-HVTC-G
Holding capacity: 6000 lbs
PART NO.
BASIC C
MECHANISM A B1 B2 DIA D E F G H J K L M1 M2 N1 N2 P Q R S T U V W X Y Z
CL-110-HVTC .236 4.33 2.60 .50 .118 .39 2.76 1.14 .472 .197 .709 .984 .71 1.10 .79 1.38 #10 or M5 .55 .630 .94 .35 1.02 1.30 4.06 .39 .75 .236
CL-310-HVTC .394 8.07 4.49 .75 .197 .55 2.97 1.57 .787 .295 .984 1.378 1.14 1.57 1.26 1.97 1/4 or M6 .91 .984 1.79 .57 1.71 2.11 5.08 .79 1.41 .315
CL-510-HVTC .472 9.49 5.47 .87 .236 .75 4.06 2.24 .984 .394 1.181 1.575 1.50 1.97 1.54 2.36 5/16 or M8 .98 1.181 2.64 .75 2.17 2.68 6.74 1.10 1.87 .315
CL-610-HVTC .630 10.91 6.97 .98 .315 .87 5.16 2.83 1.181 .394 1.772 1.969 2.05 2.56 1.97 2.76 5/16 or M8 1.38 1.378 3.33 1.02 2.74 3.43 8.59 1.30 2.24 .315

30TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

VERTICAL HANDLE

6000 3000 2000 750

lbs lbs lbs lbs

Basic Mechanism
Straight Base

Heavy-duty automotive-type production clamps designed for extreme dura-

bility. The above configuration is a basic toggle mechanism onto which an
arm and handle can be welded at any desired angle (see pages 28-30 for
other versions). The straight base is ideal for plate/tongue mounting at any
angle. Alternatively, the optional base plate can be attached to construct a Straight-base clamps
are ideal for welding
tall flanged-base clamp. Precision, close-tolerance steel components
onto plates.
throughout provide exceptionally smooth operation. Rugged alloy steel han-
dle fork. Guided-arm feature provides positive lateral arm support. All pivot
pins are hardened and ground, running in either hardened bushings or the
close-tolerance holes of hardened parts. The bottom pivot is a precision bolt
which can be adjusted, if desired, to fine tune the amount of free play. These
clamps are built to withstand abuse. With just occasional lubrication, they will
provide extremely long service life. Black oxide finish. Available in four sizes.

CL-111-HVTC Basic Mechanism, Straight Base

Smallest of the four sizes, yet still quite powerful. Arm opens 205° while Clamping Arm Base Plate
handle moves 130°. Shipping weight 0.8 lbs. (order separately) (order separately)
Holding capacity: 750 lbs

CL-311-HVTC Basic Mechanism, Straight Base

Arm opens 205° while handle moves 130°. Shipping weight 1.8 lbs.
Holding capacity: 2000 lbs
CL-511-HVTC Basic Mechanism, Straight Base Handle Vinyl Grip
Arm opens 195° while handle moves 130°. Shipping weight 3.2 lbs. (order separately) (order separately)
Holding capacity: 3000 lbs
ACCESSORIES
CL-611-HVTC Basic Mechanism, Straight Base
CLAMP
PART NO.
CLAMPING
PART NO.
BASE PART NO.
PART NO.
VINYL
Our most-powerful hold-down toggle clamp. Arm opens 195° while han- SIZE ARM PLATE HANDLE GRIP
dle moves 130°. Shipping weight 7.1 lbs. 750 lbs CL-1-HVTC-A CL-1-HVTC-P CL-1-HVTC-H CL-1-HVTC-G
Holding capacity: 6000 lbs 2000 lbs CL-3-HVTC-A CL-3-HVTC-P CL-3-HVTC-H CL-3-HVTC-G
3000 lbs CL-5-HVTC-A CL-5-HVTC-P CL-5-HVTC-H CL-5-HVTC-G
6000 lbs CL-6-HVTC-A CL-6-HVTC-P CL-6-HVTC-H CL-6-HVTC-G

PART NO.
BASIC C
MECHANISM A B1 B2 DIA D E F G H J K L M1 M2 N1 N2 P Q R S T U V W X Y Z
CL-111-HVTC .236 5.08 3.39 .50 .118 .39 2.52 1.14 .472 .197 .709 .984 1.06 1.10 .79 1.38 #10 or M5 .55 .630 1.73 .59 1.26 1.54 4.06 1.18 1.54 .236
CL-311-HVTC .394 9.25 5.67 .75 .197 .55 2.56 1.57 .787 .295 .984 1.378 1.77 1.57 1.26 1.97 1/4 or M6 .91 .984 2.97 .98 2.13 2.52 5.08 1.97 2.59 .315
CL-511-HVTC .472 10.87 6.97 .87 .236 .75 3.82 2.24 .984 .394 1.181 1.575 1.97 1.97 1.50 2.36 5/16 or M8 .98 1.181 4.02 .98 2.40 2.92 6.74 2.48 3.25 .315
CL-611-HVTC .630 12.60 8.66 .98 .315 .87 4.61 2.83 1.181 .394 1.772 1.969 2.48 2.56 1.97 2.76 5/16 or M8 1.38 1.378 5.02 1.57 3.31 3.98 8.59 2.99 3.94 .315

(Rev. 11/09) 31TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

750 lbs

150 lbs
CL-200-VTC

350 lbs

Hold-down toggle clamp with a unique finger-grip T

handle. Extremely compact design. Open arm provides
adjustable spindle location. Arm opens 92º while handle
moves 175º.

CL-200-VTC
Miniature-size T-handle clamp. Supplied with #10-32 flat-
cushion spindle CL-316112-FC and (2) CL-3166-TW
flanged washers. Shipping weight 0.2 lbs.
Holding capacity: 150 lbs
CL-300-VTC
CL-300-VTC NEW!
Medium-size T-handle clamp. Supplied with 5/16-18 flat-
cushion spindle CL-518208-FC and (2) CL-51610-TW
flanged washers. Shipping weight 0.6 lbs.
Holding capacity: 350 lbs

CL-500-VTC NEW!
Large-size T-handle clamp. Supplied with 3/8-16 flat-
cushion spindle CL-38212-FC and (2) CL-3811-TW
flanged washers. Shipping weight 1.3 lbs.
Holding capacity: 750 lbs

Also available in stainless steel...

CL-200-VTC-S CL-300-VTC-S CL-500-VTC-S CL-500-VTC

150 lbs 350 lbs 750 lbs

32TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE
A LSO E WITH
NOW AILABL OCK!
AV FETY L
SA

750 lbs

CL-200-LVTC

150 lbs

350 lbs

Same as our hold-down toggle clamps on page 28, except

with our new safety-lock feature. This safety lock
automatically engages when the clamp is closed, then
remains locked until manually disengaged by pressing the
lever before opening. This prevents the clamp from being
accidentally opened by bumping the handle. This clamp
has a unique finger-grip T handle. Extremely compact
design. Open arm provides adjustable spindle location.
Arm opens 92º while handle moves 175º.

CL-200-LVTC With Safety Lock CL-300-LVTC

Miniature-size T-handle clamp. Supplied with #10-32 flat-
cushion spindle CL-316112-FC and (2) CL-3166-TW
flanged washers. Shipping weight 0.2 lbs.
Holding capacity: 150 lbs

CL-300-LVTC With Safety Lock

Medium-size T-handle clamp. Supplied with 5/16-18 flat-
cushion spindle CL-518208-FC and (2) CL-51610-TW
flanged washers. Shipping weight 0.6 lbs.
Holding capacity: 350 lbs

CL-500-LVTC With Safety Lock

Large-size T-handle clamp. Supplied with 3/8-16 flat-
cushion spindle CL-38212-FC and (2) CL-3811-TW
flanged washers. Shipping weight 1.3 lbs.
Holding capacity: 750 lbs

Press lever to unlock

CL-500-LVTC

(Rev. 11/09) 33TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

850 lbs
Low Open Arm 625 lbs
Low Open Arm 250 lbs CL-11-TC
Low Open Arm

100 lbs
Low Open Arm
Stainless

Simple, easy-opening clamps with excellent arm reach, extend-

ing farther over workpiece than any other clamps their size.
Open arm allows spindle adjustment (see p. 35 for solid-arm
version). Arm opens 83° while handle moves 83°. Available in
four sizes.
CL-11-TC Low Open Arm, Flanged Base
Miniature clamp in stainless steel. Supplied with #8-32 hex-
head spindle CL-832203-SA-S. Shipping weight 0.1 lbs.
Holding capacity: 100 lbs
CL-111-TC Low Open Arm, Flanged Base
Small-size clamp. Accepts any 1/4-20 spindle and (2) CL-147-
TW flanged washers . . . see pages 78-82 to order. Shipping
weight 0.3 lbs.
Holding capacity: 250 lbs
CL-211-TC Low Open Arm, Flanged Base
Medium-size clamp. Accepts any 5/16-18 spindle and (2) CL-
51610-TW flanged washers . . . see pages 78-82 to order.
Shipping weight 0.5 lbs.
Holding capacity: 625 lbs
CL-311-TC Low Open Arm, Flanged Base CL-111-TC (Top dimension)
CL-211-TC (Middle dimension)
Large-size clamp. Arm extends a full 6 inches over workpiece.
Accepts any 3/8-16 spindle and (2) CL-3811-TW flanged wash- CL-311-TC (Bottom dimension)
ers . . . see pages 78-82 to order. Shipping weight 1.4 lbs.
Holding capacity: 850 lbs

CL-112-TC CL-212-TC CL-312-TC

Low Open Arm Low Open Arm Low Open Arm
Straight Base Straight Base Straight Base
250 lbs 625 lbs 850 lbs

34TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

850 lbs
Low Solid Arm
625 lbs
Low Solid Arm 250 lbs
Low Solid Arm

Simple, easy-opening clamps with excellent arm reach, extend-

ing farther over workpiece than any other clamps their size.
Solid arm for weld-on bolt retainers (see p. 34 for open-arm ver-
sion). Arm opens 83° while handle moves 83°. Available in
three sizes.

CL-113-TC Low Solid Arm, Flanged Base

Small-size clamp. Accepts any 1/4-20 spindle and a CL-1458-S
bolt retainer . . . see pages 78-82 to order. Shipping weight 0.3 lbs.
Holding capacity: 250 lbs

CL-213-TC Low Solid Arm, Flanged Base

Medium-size clamp. Accepts any 5/16-18 spindle and a CL-
51658-S or CL-518000-BR bolt retainer . . . see pages 78-82 to
order. Shipping weight 0.5 lbs.
Holding capacity: 625 lbs
CL-113-TC (Top dimension)
CL-313-TC Low Solid Arm, Flanged Base CL-213-TC (Middle dimension)
Large-size clamp. Arm extends a full 6 inches over workpiece. CL-313-TC (Bottom dimension)
Accepts any 3/8-16 spindle and a CL-3878-S or CL-316000-BR
bolt retainer . . . see pages 78-82 to order. Shipping weight 1.4 lbs.
Holding capacity: 850 lbs

CL-114-TC CL-214-TC CL-314-TC

Low Solid Arm Low Solid Arm Low Solid Arm
Straight Base Straight Base Straight Base
250 lbs 625 lbs 850 lbs

(Rev. 11/09) 35TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

VERTICAL HANDLE

850 lbs
High Open Arm
625 lbs
High Open Arm 250 lbs
High Open Arm CL-21-TC

100 lbs
High Open Arm
Stainless Steel

Simple, easy-opening clamps with extra arm height. Open arm

allows spindle adjustment (see p. 37 for solid-arm version).
Arm opens 83° while handle moves 83°. Available in four sizes.

CL-21-TC High Open Arm, Flanged Base

Miniature clamp in stainless steel. Supplied with #8-32 hex-
head spindle CL-832203-SA-S. Shipping weight 0.1 lbs.
Holding capacity: 100 lbs

CL-101-TC High Open Arm, Flanged Base

Small-size clamp. Accepts any 1/4-20 spindle and (2) CL-147-
TW flanged washers . . . see pages 78-82 to order. Shipping
weight 0.3 lbs.
Holding capacity: 250 lbs

CL-201-TC High Open Arm, Flanged Base

Medium-size clamp. Accepts any 5/16-18 spindle and (2) CL-
51610-TW flanged washers . . . see pages 78-82 to order.
Shipping weight 0.5 lbs.
Holding capacity: 625 lbs

CL-301-TC High Open Arm, Flanged Base

Large-size clamp. Accepts any 3/8-16 spindle and (2) CL- CL-101-TC (Top dimension)
3811-TW flanged washers . . . see pages 78-82 to order.
Shipping weight 1.4 lbs. CL-201-TC (Middle dimension)
Holding capacity: 850 lbs CL-301-TC (Bottom dimension)

CL-102-TC CL-202-TC CL-302-TC

High Open Arm High Open Arm High Open Arm
Straight Base Straight Base Straight Base
250 lbs 625 lbs 850 lbs

36TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

850 lbs
High Solid Arm
625 lbs
High Solid Arm

250 lbs
High Solid Arm

Simple, easy-opening clamps with extra arm height. Solid arm

for weld-on bolt retainers (see p. 36 for open-arm version). Arm
opens 83° while handle moves 83°. Available in three sizes.

CL-103-TC High Solid Arm, Flanged Base

Small-size clamp. Accepts any 1/4-20 spindle and a CL-1458-S
bolt retainer . . . see pages 78-82 to order. Shipping weight
0.3 lbs.
Holding capacity: 250 lbs

CL-203-TC High Solid

Medium-size clamp. Accepts any
Arm, Flanged Base
5/16-18 spindle and a
CL-51658-S or CL-518000-BR bolt retainer . . . see pages 78-
82 to order. Shipping weight 0.5 lbs.
Holding capacity: 625 lbs

CL-303-TC High Solid Arm, Flanged Base

Large-size clamp. Accepts any 3/8-16 spindle and a CL-3878-S
or CL-316000-BR bolt retainer . . . see pages 78-82 to order.
Shipping weight 1.4 lbs.
Holding capacity: 850 lbs CL-103-TC (Top dimension)
CL-203-TC (Middle dimension)
CL-303-TC (Bottom dimension)

CL-104-TC CL-204-TC CL-304-TC

High Solid Arm
High Solid Arm High Solid Arm
Straight Base
Straight Base Straight Base
850 lbs
250 lbs 625 lbs

(Rev. 11/09) 37TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

5000 lbs
Low Arm

2500 lbs
Low Arm
CL-45-HDC-121
1500 lbs
Low Arm
(4) HOLES 11/32 DIA
FOR 5/16 OR M8 SCREWS

5/8 1-3/4
2-1/4
1/4 1-3/4
Compact heavy-duty clamps with forged steel handles and 2-1/4
clamping arms, available in three sizes. Low clamping arm
extends far over workpiece. Also available with other
arm/handle configurations . . . see pages 39 and 40.
Simple, easy-opening linkage. Arm opens 83° while han-
dle moves 83°. Weld-on flanged base is optional. To order 1/2 5-7/8
clamp with flanged base attached, add "S" to part no.
(example: CL-45-HDC-121S). 13/16
9/16
!
NEW 1
25/32
3/8 5/16
CL-45-HDC-121 Low Arm 4-5/8
1-5/32 5/8
1-1/8
Smallest of the three sizes, yet still quite powerful.
Shipping weight 2.0 lbs. 6-7/32 4

Holding capacity: 1500 lbs CL-50-HDC-121

CL-50-HDC-121
Medium-size clamp with high strength.
Low Arm
Shipping weight
2.5 lbs.
Holding capacity: 2500 lbs

CL-51-HDC-121 Low Arm

Largest of the three sizes. Shipping weight 5.0 lbs.
Holding capacity: 5000 lbs

Available with
standard flanged
base attached...

Add “S” to part no. CL-51-HDC-121

38TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE

5000 lbs
High Arm

2500 lbs
High Arm

CL-40-HDC-211
1500 lbs
High Arm

Compact heavy-duty clamps with forged steel handles and

clamping arms, available in three sizes. High clamping arm
provides extra room for thick workpieces. Also available
with other arm/handle configurations . . . see pages 38 and
40. Simple, easy-opening linkage. Arm opens 83° while
handle moves 83°. Weld-on flanged base is optional. To
order clamp with flanged base attached, add “S” to part no.
(example: CL-40-HDC-211S).

!
CL-40-HDC-211 NEW High Arm
Smallest of the three sizes, yet still quite powerful.
Shipping weight 2.0 lbs.
Holding capacity: 1500 lbs
CL-60-HDC-211

CL-60-HDC-211 High Arm

Medium-size clamp with high strength. Shipping weight
2.5 lbs.
Holding capacity: 2500 lbs

CL-61-HDC-211 High Arm

Larger of the three sizes. Shipping weight 5.0 lbs.
Holding capacity: 5000 lbs

Available with standard Also available

flanged base attached . . . air powered . .
.

CL-3000-PTC
Add “S” to part no. (page 74) CL-61-HDC-211

(Rev. 11/09) 39TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
VERTICAL HANDLE
Custom heavy-duty forged clamps built to your specifica-
tions, with the same features as the clamps shown on pages
38 and 39. Available in three sizes. Choose from the 32 con-
figurations shown below. (Top part no. is for 1500-lb clamp,
middle part no. is for 2500-lb clamp, bottom part no. is for
5000-lb clamp). Simple, easy-opening linkage. Arm opens
83° while handle moves 83°. Weld-on flanged base is
optional. To order clamp with flanged base attached, add “S”
to part no. (example: CL-40-HDC-111S).
!
CL-40/45-HDC-XXX NEW
Smallest of the three sizes, yet still quite powerful. Shipping
weight 2.0 lbs.
Holding capacity: 1500 lbs

CL-50/60-HDC-XXX
Medium-size clamp with high strength. Shipping weight 2.5 lbs.
Holding capacity: 2500 lbs

CL-51/61-HDC-XXX CL-40/45-HDC-XXX (Top dimension)

Largest of the three sizes. Shipping weight 5.0 lbs. CL-50/60-HDC-XXX (Middle dimension)
Holding capacity: 5000 lbs CL-51/61-HDC-XXX (Bottom dimension)
Low Arm High Arm
CL-45-HDC-111 CL-45-HDC-311 CL-40-HDC-111 CL-40-HDC-311
CL-50-HDC-111 CL-50-HDC-311 CL-60-HDC-111 CL-60-HDC-311
CL-51-HDC-111 CL-51-HDC-311 CL-61-HDC-111 CL-61-HDC-311

CL-45-HDC-121 CL-45-HDC-321 CL-40-HDC-121 CL-40-HDC-321

CL-50-HDC-121 CL-50-HDC-321 CL-60-HDC-121 CL-60-HDC-321
CL-51-HDC-121 CL-51-HDC-321 CL-61-HDC-121 CL-61-HDC-321

CL-45-HDC-131 CL-45-HDC-331 CL-40-HDC-131 CL-40-HDC-331

CL-50-HDC-131 CL-50-HDC-331 CL-60-HDC-131 CL-60-HDC-331
CL-51-HDC-131 CL-51-HDC-331 CL-61-HDC-131 CL-61-HDC-331

CL-45-HDC-141 CL-45-HDC-341 CL-40-HDC-141 CL-40-HDC-341

CL-50-HDC-141 CL-50-HDC-341 CL-60-HDC-141 CL-60-HDC-341
CL-51-HDC-141 CL-51-HDC-341 CL-61-HDC-141 CL-61-HDC-341

CL-45-HDC-211 CL-45-HDC-411 CL-40-HDC-211 CL-40-HDC-411

CL-50-HDC-211 CL-50-HDC-411 CL-60-HDC-211 CL-60-HDC-411
CL-51-HDC-211 CL-51-HDC-411 CL-61-HDC-211 CL-61-HDC-411

CL-45-HDC-221 CL-45-HDC-421 CL-40-HDC-221 CL-40-HDC-421

CL-50-HDC-221 CL-50-HDC-421 CL-60-HDC-221 CL-60-HDC-421
CL-51-HDC-221 CL-51-HDC-421 CL-61-HDC-221 CL-61-HDC-421

CL-45-HDC-231 CL-45-HDC-431 CL-40-HDC-231 CL-40-HDC-431

CL-50-HDC-231 CL-50-HDC-431 CL-60-HDC-231 CL-60-HDC-431
CL-51-HDC-231 CL-51-HDC-431 CL-61-HDC-231 CL-61-HDC-431

CL-45-HDC-241 CL-45-HDC-441 CL-40-HDC-241 CL-40-HDC-441

CL-50-HDC-241 CL-50-HDC-441 CL-60-HDC-241 CL-60-HDC-441
CL-51-HDC-241 CL-51-HDC-441 CL-61-HDC-241 CL-61-HDC-441

40TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

W A LSO
NO B LE
I L A
AVA RIC!
T
IN ME

Sizes marked * are also available

in stainless steel

All Carr Lane toggle clamps are DFARS and RoHS compliant.

Standard SPC Design

p. 42-47
Most popular series of push/pull
100 lbs* 300 lbs* 800 lbs 5000 lbs clamps. Plunger advances and locks
by moving the handle forward toward
it. Clamp can also be used for pulling
instead of pushing (handle locks back
in downward position also). Choice of
seven sizes.
150 lbs* 300 lbs 2500 lbs 16000 lbs

Horizontal Handle
p. 49
Reverse-action push clamp. Plunger
advances and locks by moving the
handle backward into horizontal posi-
600 lbs tion.

PC Design
pp. 50-51
Durable push/pull clamps with nodular
iron bases. Plunger advances and
locks by moving the handle forward
toward it. Clamp can also be used for
pulling instead of pushing (handle
500 lbs 850 lbs 1500 lbs locks back in downward position also).
Choice of three sizes.

Threaded Body
p. 52-53
Compact push/pull clamps for mount-
ing through panels, plates, or angle
brackets. Install in a drilled or tapped
hole. Plunger locks in either extended
or retracted position. Rotate clamp to
200 lbs* 300 lbs* 700 lbs position handle anywhere within 360°.
Choice of three sizes.

(Rev. 11/09) 41TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL
(3) HOLES 11/64 DIA
3/8 FOR #8 OR M4 SCREWS

1/4 DIA 5/8 1-1/16

7/16 DIA
5/16 5/8
1-5/16
CL-51-SPC
Tapped Plunger Externally Threaded
Plunger TAPPED #8-32 1-25/32
X 1/2 DEEP
1/4
RADIUS 5/8
TRAVEL
1-5/16
100 lbs
5/8

Externally Threaded
Plunger 3/32 1-9/32 1-7/32
2-19/32
CL-50-SPC (Metric No. CLM-50-SPC) Also available Also available
Miniature plunger clamp, perfect for electronics fixturing in stainless steel . . . air powered . . .
and other light-duty applications. Locks in extended or
retracted position. 5/8" plunger travel. Tapped-plunger ver-
sion supplied with #8-32 nylon hex-head spindle
CL-832203-SA (M4 in metric). Also available with 1/4-20
externally threaded plunger. Shipping weight 0.2 lbs.
CL-50-SPC-S CL-600-PPC
Holding capacity: 100 lbs (page 73)

!
NEW

150 lbs

Tapped Plunger

CL-60-SPC (Metric No. CLM-60-SPC)

Heavier-duty version of our smallest plunger clamp above. Also available
This is a powerful clamp in an extremely compact size. in stainless steel . . .
Unique base allows bottom or side mounting. Locks in
extended or retracted position. 5/8" plunger travel. Plunger
is tapped to accept any #8-32 spindle (M4 in metric) ... see
pages 78-81 to order. Shipping weight 0.2 lbs.
Holding capacity: 150 lbs
CL-60-SPC-S

(Rev. 11/09) 42TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

300 lbs

CL-100-SPC (Metric No. CLM-100-SPC)

Also available
in stainless steel . . .
Tiny, yet extremely powerful plunger clamp with a forged
steel base. Requires very little mounting space due to its
narrow base and compact low profile. Locks in extended or
retracted position. 5/8" plunger travel. Plunger is tapped to
accept any 1/4-20 spindle (M6 in metric) . . . see pages 78-
81 to order. Shipping weight 0.5 lbs.
Holding capacity: 300 lbs CL-100-SPC-S

O
W ALS E WITH
NO ILABL CK!
AVA ETY LO
SAF

300 lbs

CL-100-LSPC (Metric No. CLM-100-LSPC)

Press lever
to unlock
Also available
in stainless steel . . .
Same as the toggle clamp shown above, except with our
new safety-lock feature. This safety lock automatically
engages when the clamp is closed, then remains locked
until manually disengaged by pressing the lever before
opening. This prevents the clamp from being accidentally
opened by bumping the handle. Shipping weight 0.6 lbs.
Holding capacity: 300 lbs CL-100-LSPC-S

(Rev. 11/09) 43TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

PUSH / PULL

300 lbs

CL-150-SPC (Metric No. CLM-150-SPC)

Medium-size plunger clamp that locks in extended or
retracted position. 1-1/4" plunger travel. Plunger is tapped
to accept any 5/16-18 spindle (M8 in metric) ... see pages
78-81 to order. Shipping weight 0.7 lbs.
Holding capacity: 300 lbs

"My best friend is the one

who brings out the best in me."

Henry Ford

44TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

800 lbs

CL-250-SPC (Metric No. CLM-250-SPC)

Heavier clamp with extra plunger height. Locks in extend-
ed or retracted position. 1-5/8" plunger travel. Plunger is
tapped to accept any 3/8-16 spindle (M10 in metric) . . . see
pages 78-81 to order. Shipping weight 1.9 lbs.

Holding capacity: 800 lbs

! TING ED
NEW -ADJUS G-LOAD 1-27/32 (4) HOLES 11/32 DIA

SELF SPRIN 1-1/4 DIA FOR 5/16" OR M8 SCREWS

H
WIT GER! 3/4 DIA 1-5/8
N
PLU 2-1/4

5/16 1-5/8 21/32

2-1/4
5-3/4

1-5/8 MAX
1/4 TRAVEL
.20"
CLAMPING 4-9/16
RANGE
200 lbs
Spring Force 1-3/4

1/4 3-7/8 2-9/16

CL-255-SPC 6-3/4
Spring-loaded version of CL-250-SPC above. Heavier
clamp with extra plunger height. Locks in extended position
only. 1-5/8" maximum plunger travel with a .20" clamping
range. Patent number 6,905,116. Shipping weight 1.9 lbs.

Spring force (±10%): 200 lbs

(Rev. 11/09) 45TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

2500 lbs

CL-350-SPC (Metric No. CLM-350-SPC)

Compact heavy-duty plunger clamp with an extremely low
profile. Rugged forged steel base. Locks in extended or
retracted position. 2" plunger travel. Plunger is tapped to
accept any 3/8-16 spindle (M10 in metric) . . . see pages
78-81 to order. Shipping weight 2.0 lbs.

Holding capacity: 2500 lbs

Press lever
to unlock
O H
W ALS LE WIT !
NO AILAB LOCK
AV FETY
SA

(6) HOLES 11/32 DIA

FOR 5/16" OR M8 SCREWS

1-5/8
5/8 DIA
2-1/4

37/64 1-3/8 1-5/8

5
2500 lbs
5-11/32
TAPPED 3/8"-16
X 1 DEEP LOCK

CL-350-LSPC With Safety Lock

Same as the toggle clamp shown above, except with our
13/32
RADIUS
5/16
2
TRAVEL 3-1/8

new safety-lock feature. This safety lock automatically 7/32 13/16

engages when the clamp is closed, then remains locked
until manually disengaged by pressing the lever before 2 4-21/32
opening. This prevents the clamp from being accidentally 7-1/16
opened by bumping the handle. Shipping weight 2.0 lbs.
Holding capacity: 2500 lbs

46TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

(6) HOLES 13/32 DIA

FOR 3/8 OR M10 SCREWS
2-1/8

7/8 DIA 3

11/16 3-9/16 3-9/16

8-1/2

1/2-13 THREAD 7-3/4

51 DEEP

4" TRAVEL
11/16 9/16 4-13/16
5000 lbs RADIUS

1-1/4

3/8
5-5/16 8
CL-450-SPC (Metric No. CLM-450-SPC) 12-11/16
Extra-heavy-duty clamp features a full 4" plunger travel!
Rugged nodular iron base and a 7/8"-diameter plunger
combine to handle the toughest clamping jobs. Locks in
extended or retracted position. Plunger is tapped to accept
any 1/2-13 spindle (M12 in metric) . . . see pages 78-81 to
order. Shipping weight 7.0 lbs.
Holding capacity: 5000 lbs

16000 lbs

CL-650-SPC (Metric No. CLM-650-SPC)

Strongest plunger clamp available. Handle and base are
made of alloy steel. Precision unit with snap-ring pivot pins to
allow removing the plunger even after the clamp is mounted.
Locks in extended or retracted position. 3" plunger travel.
Plunger is tapped to accept any 5/8-11 spindle (M16 in
metric). . . see pages 78-81 to order. Shipping weight 5.7 lbs.
Holding capacity: 16000 lbs

(Rev. 11/09) 47TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

Large to Small...
Lift Your Load Safely
With Carr Lane Hoist Rings

NEW! Extra-large Swivel Hoist Rings

with our patented EZ-Torque™ sys-
Toggle Clamps with Safety Locks. tem that allows tightening several
Carr Lane has introduced a variety of smaller bolt heads with a standard
new toggle clamps with optional torque wrench instead of tightening
safety locks, including latch-action, one large bolt with a special tool.
vertical-handle, horizontal-handle, and Swivel Hoist Rings pivot 180 degrees
push/pull types. All Carr Lane toggle and swivel 360 degrees simultaneous-
clamps have a comfortable handle ly to allow lifting from any direction.
grip, in steel or optional stainless.
Carr Lane Mfg. Co., www.carrlane.com

From large to small, in

dozens of types, Carr Lane
has the hoist ring for your
application.

Carr Lane’s lot number marking

Quick Release Pins. Carr Lane pins guarantees quality by providing
come with L, T, button or ring handles. traceability for:
Choose from ball lock pins, lifting • Date of manufacture
pins, detent pins, or the ball lock • Material certification
mounting clamp. Many sizes available. • Magnaflux testing certification
Carr Lane Mfg. Co., www.carrlane.com • Heat treatment certification

Pivoting hoist rings, swivel hoist rings, side-pull swivel hoist

rings and lifting eyes are some of the types offered by Carr
Lane, ranging from low profile versions to heavy-duty, extra-
large types with load capacities up to 250,000 lbs.

Visit CarrLane.com and search our online catalog for hoist rings
Knobs, Handles, Hand Wheels. Need and any of our 100,000 other products.
to take hold? A variety of knobs,
handles and hand wheels, in metal or
plastic, are available from Carr Lane.
Many new items. MANUFACTURING CO.
4200 Carr Lane Ct., P.O. Box 191970
Carr Lane Mfg. Co., www.carrlane.com St. Louis, Missouri 63119-7970
R
Phone: 314-647-6200, FAX: 314-647-5736
ISO 9001-2008 CERTIFIED Web Site: www.carrlane.com

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

Horizontal Handle

600 lbs

CL-276-SPC
Straight Base
with Bracket

CL-275-SPC (Metric No. CLM-275-SPC)

Similar to CL-250-SPC except with reverse handle action. Plunger
advances and locks by moving handle backward into horizontal
position. 1-3/16" plunger travel. Plunger is tapped to accept any
3/8-16 spindle (M10 in metric) . . . see pages 78-81 to order.
Straight-base version supplied with separate base bracket to allow
mounting clamp at an angle. Shipping weight 1.5 lbs.
Bracket included with CL-276-SPC
Holding capacity: 600 lbs

E W ! U S TING ADED
N
E L F -ADJ ING-LO
Horizontal Handle
S
T H SPR
WI GER!
N
PLU (4) HOLES 11/32 DIA
FOR 5/16" OR M8 SCREWS
1-5/8
1-7/8 2-1/4
3/4 DIA 1/2

1-1/16 DIA 1/4

5/16 1-5/8
2-1/4

200 lbs
Spring
16000Force
lbs

3/4
.20" TRAVEL 7-1/16
CLAMPING 2-1/4
CL-285-SPC RANGE
Spring-loaded version of CL-275-SPC above. Plunger 1-3/4
advances and locks by moving handle backward into horizontal
position. 3/4" maximum plunger travel with a .20" clamping 1/4 3-13-16 2-1/2
range. Patent number 6,905,116. Shipping weight 1.5 lbs. 12-1/16

Spring force (±10%): 200 lbs

(Rev. 11/09) 49TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

1500 lbs

850 lbs CL-100-PC

500 lbs

Durable plunger clamp with nodular iron base. Locks in

either extended or retracted position. Choice of three
sizes.

CL-100-PC (Metric No. CLM-100-PC)

Small-size clamp with 1-3/16" plunger travel. Accepts any
5/16-18 spindle (M8 in metric). . . see pages 78-81 to
order. Shipping weight 0.9 lbs.
Holding capacity: 500 lbs

CL-200-PC
CL-200-PC (Metric No. CLM-200-PC)
Medium-size clamp with 1-5/8" plunger travel. Accepts
any 3/8-16 spindle (M10 in metric). . . see pages 78-81 to
order. Shipping weight 1.4 lbs.
Holding capacity: 850 lbs

CL-300-PC (Metric No. CLM-300-PC)

Large-size clamp with 2-11/32" plunger travel. Accepts
any 1/2-13 spindle (M12 in metric). . . see pages 78-81 to
order. Shipping weight 3.2 lbs.
Holding capacity: 1500 lbs

Also available air powered . . .

CL-1500-PPC
850 lbs CL-300-PC
(page 76)

50TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL
O
W ALS LE WITH
NO ILAB CK!
AVA L O
ETY
SAF

1500 lbs

CL-100-LPC
850 lbs

500 lbs

Same as the toggle clamps shown on opposite page 50,

except with our new safety-lock feature. This safety lock
automatically engages when the clamp is closed, then
remains locked until manually disengaged by pressing the
lever before opening. This prevents the clamp from being
accidentally opened by bumping the handle.

Durable plunger clamp with nodular iron base. Locks in

extended or retracted position (safety lock functions only in
extended position). Choice of three sizes.

CL-100-LPC
Small-size clamp with 1-3/16” plunger travel. Accepts any
CL-200-LPC
5/16-18 spindle . . .see pages 78-81 to order. Shipping weight
0.9 lbs.
Holding Capacity: 500 lbs

CL-200-LPC
Medium-size clamp with 1-5/8” plunger travel. Accepts any
3/8-16 spindle . . .see pages 78-81 to order. Shipping weight
1.4 lbs.
Holding Capacity: 850 lbs

CL-300-LPC
Large-size clamp with 2-11/32” plunger travel. Accepts any
1/2-13 spindle . . .see pages 78-81 to order. Shipping weight
3.2 lbs.
Holding Capacity: 1500 lbs

Press lever to unlock

CL-300-LPC

(Rev. 11/09) 51TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

700 lbs
CL-150-TPC

300 lbs

200 lbs

Compact plunger clamps for mounting through panels, plates,

or angle brackets. Install in a drilled or tapped hole, securing
with the locknut provided. Plunger locks in either extended or
retracted position. Rotate clamp to position handle anywhere
within 360°. Choice of three sizes.

CL-150-TPC (Metric No. CLM-150-TPC)

Small-size clamp with 3/4" plunger travel. Installs in a 5/8"-
CL-250-TPC
diameter drilled hole, or a 5/8-18 tapped hole (M16x1.5 in
metric). Accepts any 1/4-20 spindle (M6 in metric). . . see
pages 78-81 to order. Shipping weight 0.4 lbs.
Holding capacity: 200 lbs

CL-250-TPC (Metric No. CLM-250-TPC)

Medium-size clamp with 1-1/2" plunger travel. Installs in a
3/4"-diameter drilled hole, or a 3/4-16 tapped hole (M20x1.5 in
metric). Accepts any 5/16-18 spindle (M8 in metric). . . see
pages 78-81 to order. Shipping weight 0.7 lbs.
Holding capacity: 300 lbs

CL-350-TPC (Metric No. CLM-350-TPC)

Large-size clamp with 2-5/8" plunger travel. Installs in a 1"-
diameter drilled hole, or a 1"-14 (M27x2 in metric) tapped hole.
Accepts any 3/8-16 spindle (M10 in metric). . . see pages 78-
81 to order. Shipping weight 1.5 lbs.
Holding capacity: 700 lbs
Mounting Bracket for CL-250-TPC . . .
CL-350-TPC
Also available in stainless steel . . .

CL-150-TPC-S CL-250-TPC-S CL-350-TPC-S

CL-250-TPCA 200 lbs 300 lbs 700 lbs

52TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
PUSH / PULL

E W ! U S TING ADED
N J
-AD G-LO
SELF SPRIN
H
WIT GER!
N
PLU

200 lbs
Spring Force

100 lbs
Spring Force

Compact plunger clamps for mounting through panels, plates,

or angle brackets. Install in a drilled or tapped hole, securing
with the locknut provided. Plunger locks only in extended
position. Rotate clamp to position handle anywhere within
360°. Patent number 6,905,116. Choice of two sizes.

CL-255-TPC
Medium-size clamp with 1-1/2" maximum plunger travel and a
.20" clamping range. Installs in a 3/4"-diameter drilled hole, or CL-255-TPC
a 3/4-16 tapped hole. Shipping weight 0.7 lbs.
Spring force (±10%): 100 lbs 1"-14 THREAD

3/4 DIA
1-1/2
CL-355-TPC
Large-size clamp with 2-5/8" maximum plunger travel and a
1/4 1"-14 THREAD
7/8
3/16 1-7/8

.20" clamping range. Installs in a 1"-diameter drilled hole, or a 15/16

1"-14 tapped hole. Shipping weight 1.5 lbs.
Spring force (±10%): 200 lbs
4-13/16
2-5/8 MAX
5/16 TRAVEL
.20"
CLAMPING
RANGE
13/16
Mounting Bracket for CL-255-TPC . . .
1-1/4 3-5/8
SQUARE
6-11/16 1-5/16

360 HANDLE HANDLE POSITION

ROTATION WITH PLUNGER
RETRACTED
CL-355-TPC

CL-250-TPCA

(Rev. 11/09) 53TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

TOGGLE EDGE CLAMPS

All Carr Lane toggle clamps are DFARS and RoHS compliant.

Automatically Adjusting
p. 55
Unique Toggle Edge Clamp applies
force forward and downward at the
same time. This quick-acting, self-
adjusting clamp automatically compen-
sates for variations in workpiece size.
Clamping force is always consistent
after setting once.

750 lbs

54TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE EDGE CLAMPS

Toggle Edge Clamps apply force forward

and downward at the same time.
750 lbs
Automatic Toggle Clamp
(Self Adjusting)
(4) HOLES 21/64 DIA
FOR 5/16 OR M8 SCREWS

CL-550-ATEC 2-3/8
15/16
Automatic Toggle Edge Clamp 1-5/8 9/16
Unique Toggle Edge Clamp applies force forward and
downward at the same time. Automatically adjusts for 1-1/4
5/16
different workpiece sizes. Clamps with the same, 2-1/16
repeatable force anywhere within its 9/32" automatic-
adjustment range.
Easy to use. Simply set desired clamping force once, after
mounting, then operate just like a standard toggle clamp.
The patented adjusting mechanism does the rest. For
mounting on T-slotted tables, see slotted adapters below.
ADJUSTMENT
Hardened clamping nose grips workpiece firmly to apply SCREW FOR
downthrust force. Handle moves 80° while nose pivots SETTING FORCE
back for loading. Patent no. 4,407,493. Other patents
VINYL GRIP
pending. Shipping weight 1.8 lbs. 8-1/4
Holding capacity: 750 lbs
1-13/32 MAX
CLEARANCE HEIGHT

3-1/8
1-1/4 1-1/8
MAX MIN 5/8

5/16
1-23/32
1-15/16 7-11/16
9/32
9/32 MAX CLAMPING RANGE

For slotted adaptors

9/32" Automatic-Adjustment Range see p. 61MF

(Rev. 11/09) 55TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION

Sizes marked * are also available in

stainless steel

All Carr Lane toggle clamps are DFARS and RoHS compliant.

Adjustable U Bolt
p. 58-61
Latch-action clamp with a threaded U
bolt for adjustability. Supplied with
matching latch plate (smallest three
sizes). Large, comfortable handle grip.
Available in five sizes.
360 lbs* 700 lbs* 2000 lbs* 4000 lbs 7500 lbs

Right-Angle Adjustable U Bolt

p. 62
Similar to the latch clamp above, except
with its pulling direction perpendicular to
the base. Supplied with matching latch
plate. Large, comfortable handle grip.
Available in three sizes.

500 lbs* 1000 lbs* 2000 lbs*

Adjustable Hook
p. 57
Popular hook-type latch clamp. Hook is
threaded at one end for easy
adjustment. Base rotates 90° to allow
horizontal or vertical latching. Available
375 lbs* 1000 lbs in two sizes.

Fixed Length
p. 63
Latch clamp with fixed reach for
installation where no length adjustment
is required. Adjustable stop allows
latching at different heights. Available in
two sizes.
375 lbs* 1200 lbs

56TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION

1000 lbs

375 lbs

Latch clamp with a versatile hook for grasping a rod or

rim. Hook is threaded at one end to allow adjustment after
mounting. Base pivots to allow horizontal or vertical CL-250-PA
latching. Choice of two sizes. Optional latch plate can be
mounted as shown in the drawings, or reversed, for
mounting flexibility.

CL-250-PA
Medium-size latch clamp with a 4-inch drawing
movement. Threaded hook allows a 5/16-inch adjustment
range. Shipping weight 0.8 lbs. Order matching latch plate
CL-250-PA-L separately (CL-250-PA-S-L in stainless).
Holding capacity: 375 lbs

CL-350-PA
Large-capacity latch clamp with 6-1/8-inch drawing
movement. Threaded hook allows a 3/4-inch adjustment
range. Shipping weight 2.5 lbs. Order matching latch plate
CL-350-PA-L separately.
Holding capacity: 1000 lbs

E
A I L ABL
AV L
NOW MANUA CL-350-PA
H !
WIT Y LOCK Also available in Extra hooks
ET stainless steel . . . available . . .
SAF
CL-257-PA
Same as CL-250-PA except with a CL-251-PA
manual safety lock. Push knob in to Narrow Base CL-250-PA-S CL-250-PA-HOOK
lock, pull knob out to unlock. 375 lbs CL-250-PA-S-HOOK
Holding capacity: 375 lbs CL-350-PA-HOOK

(Rev. 11/09) 57TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION

2000 lbs

CL-100-PA
700 lbs

360 lbs

Versatile latch clamp with a threaded U bolt for

adjustability. Supplied with matching latch plate. Large,
comfortable handle grip. Available in three sizes (also see
page 59 for two larger sizes).

CL-100-PA
Miniature latch clamp with high holding capacity. 1-3/16-
inch drawing movement. Threaded U bolt allows a 25/64-
inch adjustment range. Shipping weight 0.2 lbs.
Holding capacity: 360 lbs

CL-200-PA
CL-200-PA
Medium-size latch clamp with 2-inch drawing movement.
Threaded U bolt allows a 3/8-inch adjustment range.
Shipping weight 0.4 lbs.
Holding capacity: 700 lbs

CL-300-PA
Heavy-duty latch clamp. Well-suited for applications such
as plastic molding. 2-1/2-inch drawing movement.
Threaded U bolt allows a 15/16-inch adjustment range.
Shipping weight 1.5 lbs.
Holding capacity: 2000 lbs

Also available in stainless steel. . .

CL-100-PA-S CL-200-PA-S CL-300-PA-S

360 lbs 700 lbs 2000 lbs
CL-300-PA

58TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION

Optional
Latch Plate
CL-500-PAA

4000 lbs

CL-400-PA
Heavier-duty version of the latch clamps on page 49.
Strong enough to resist the high expansion forces
generated in polyurethane molds. Rugged alloy steel base
and latch plate (order latch plate separately). Threaded U
bolt allows a 3/4-inch adjustment range. 2-7/16" drawing
movement. Shipping weight 2.8 lbs.
Holding capacity: 4000 lbs

(8) HOLES 13/32 DIA FOR 3/8 OR M10 SCREWS

2-1/4
1-3/8 7/16 2-1/8 U-BOLT SPACING

Optional 3-1/8 3-1/8

Latch Plate 2-1/4
CL-500-PAA

9/16 2-1/4 2-1/4 HOLE SPACING

3-3/8
1-3/8 MIN DRAWING MOVEMENT
1-1/8 1-1/2
ADJUSTMENT
1

1/2-13 THREAD
(1/2 DIA U-BOLT) 3-3/4

1-1/8
7500 lbs
7/16

OPTIONAL LATCH 1 MIN

7-19/32 3/8
PLATE (ORDER
CL-500-PA SEPARATELY) 8-11/16 MIN
Strongest latch clamp available. Alloy steel handle Also available in stainless steel...
provides even greater strength than the CL-400-PA
above, yet with a more-compact overall size. Rugged CL-500-PA-S (Clamp)
alloy steel base and latch plate (order latch plate
separately). Threaded U bolt allows a 1-1/8-inch
adjustment range. 1-3/8" drawing movement. Shipping
weight 3.3 lbs. CL-500-PAA-S (Latch Plate)
Holding capacity: 7500 lbs

(Rev. 11/09) 59TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION

O H
W ALS LE WIT
NO AILAB LOCK!
AV FETY
SA

2000 lbs

700 lbs CL-100-LPA

360 lbs

Same as our latch clamps on page 58 except with our

new safety-lock feature. This safety lock automatically
engages when the clamp is closed, then remains locked
until manually disengaged by pressing the lever before
opening. This prevents the latch clamp from being
accidentally opened by bumping the handle.

Versatile latch clamp with a threaded U bolt for

adjustability. Supplied with matching latch plate. Large,
comfortable handle grip. Available in two sizes (also see
page 61 for two larger sizes).
!
CL-100-LPA NEW With Safety Lock
Miniature latch action clamp with high holding capacity. 1-
3/16-inch drawing movement. Threaded U bolt allows a CL-200-LPA
25/64-inch adjustment range. Shipping weight 0.2 lbs.
Holding capacity: 360 lbs

CL-200-LPA With Safety Lock

Medium-size latch clamp with 2-inch drawing movement.
Threaded U bolt allows a 3/8-inch adjustment range.
Shipping weight 0.4 lbs.
Holding capacity: 700 lbs

CL-300-LPA With Safety Lock

Heavy-duty latch clamp. Well-suited for applications such
as plastic molding. 2-1/2-inch drawing movement.
Threaded U bolt allows a 15/16-inch adjustment range.
Shipping weight 1.5 lbs.
Holding capacity: 2000 lbs
Also available in stainless steel. . .

CL-100-LPA-S CL-200-LPA-S CL-300-LPA-S

360 lbs 700 lbs 2000 lbs
CL-300-LPA

60TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION
A LSO LE WITH! Optional Safety Lock
NOW AILAB LOCK (Press lever to unlock)
AV FETY
Optional
Latch Plate SA (8) HOLES 13/32 DIA
CL-500-PAA FOR 3/8" OR M10 SCREWS
2-1/4
1-3/8 7/16 1-5/8 U-BOLT SPACING

3-1/8 3-1/8
2-1/4

9/16 2-1/4 2-1/4 HOLE SPACING

3-3/8
2-7/16 DRAWING MOVEMENT
4000 lbs 3/4 ADJUSTMENT
1-31/32

CL-400-LPA With Safety Lock

Same as our latch clamps on page 59 except with our new 1 3/8"-16 THREAD 4
safety-lock feature. This safety lock automatically engages (3/8 DIA U-BOLT)
when the clamp is closed, then remains locked until
manually disengaged by pressing the lever before opening. 1-1/8
This prevents the latch clamp from being accidentally 7/16 3/8
opened by bumping the handle. Rugged alloy steel base 1 MIN LOCK
and latch plate (order latch plate separately). Threaded U 8-3/8
bolt allows a 3/4-inch adjustment range. 2-7/16" drawing 9-13/32 MIN
movement. Shipping weight 2.8 lbs. OPTIONAL LATCH
PLATE (ORDER
Holding capacity: 4000 lbs SEPARATELY)

(8) HOLES 13/32 DIA FOR 3/8 OR M10 SCREWS

LSO LE WITH! 2-1/4
2-1/8 U-BOLT
7/16
A
NOW AILAB LOCK 1-3/8 SPACING
Optional AV FETY
SA 3-1/8
Latch Plate
3-1/8
2-1/4
CL-500-PAA

9/16 2-1/4 2-1/4 HOLE

SPACING
3-3/8
1-3/8 DRAWING MOVEMENT
1-1/8 1-1/2
ADJUSTMENT
1

1/2-13 THREAD
(1/2 DIA U-BOLT) 3-3/4

1-1/8
7500 lbs
7/16
1 MIN LOCK
OPTIONAL LATCH 3/8
PLATE (ORDER SEPARATELY) 7-19/32
CL-500-LPA With Safety Lock 8-11/16 MIN
Same as our latch clamps on page 59 except with our new
safety-lock feature. This safety lock automatically engages
when the clamp is closed, then remains locked until
manually disengaged by pressing the lever before opening. Also available in stainless steel...
This prevents the latch clamp from being accidentally
opened by bumping the handle. Rugged alloy steel base CL-500-LPA-S (Clamp)
and latch plate (order latch plate separately). Threaded U
bolt allows a 1-1/8-inch adjustment range. 1-3/8" drawing
movement. Shipping weight 3.3 lbs.
Holding capacity: 7500 lbs CL-500-PAA-S (Latch Plate)

(Rev. 11/09) 61TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION

CL-110-PA

2000 lbs 1000 lbs

500 lbs

Similar to the adjustable-U-bolt latch clamps on page 58,

except with their pulling direction perpendicular to the
base. Supplied with matching latch plate. Large,
comfortable handle grip. Available in three sizes.

CL-110-PA
Miniature latch clamp with high holding capacity. 1-1/2-
inch drawing movement. Threaded U bolt allows a 7/16-
inch adjustment range. Shipping weight 0.3 lbs.
Holding capacity: 500 lbs
CL-210-PA
CL-210-PA
Medium-size latch clamp with 2-1/16-inch drawing
movement. Threaded U bolt allows an 11/16-inch
adjustment range. Shipping weight 0.6 lbs.
Holding capacity: 1000 lbs

CL-310-PA
Heavy-duty latch clamp. Well-suited for applications such
as plastic molding. 2-1/2-inch drawing movement.
Threaded U bolt allows an 1-1/8-inch adjustment range.
Shipping weight 1.4 lbs.
Holding capacity: 2000 lbs

Also available in stainless steel. . .

CL-110-PA-S CL-210-PA-S CL-310-PA-S

500 lbs 1000 lbs 2000 lbs CL-310-PA

62TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
LATCH ACTION

1200 lbs

375 lbs

Latch clamp with fixed reach for installation where no length

adjustment is required. An adjustable stop allows latching at
different angles. Available in two sizes.

CL-150-PA
Medium-size clamp with 4-inch drawing movement.
Shipping weight 0.8 lbs.

Holding capacity: 375 lbs

CL-170-PA CL-150-PA

Larger clamp with 3-3/8-inch drawing movement. Shipping

weight 1.2 lbs.

Holding capacity: 1200 lbs

Also available in stainless steel...

CL-150-PA-S CL-170-PA

(Rev. 11/09) 63TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE PLIERS

Sizes marked * are also available in

stainless steel

All Carr Lane toggle clamps are DFARS and RoHS compliant.

Forged Toggle Pliers

pp. 65-67
Powerful forged steel toggle pliers.
Available in five sizes. Larger sizes
feature a quick-release lever for easy
200 lbs 350 lbs 700 lbs 700 lbs 700 lbs opening.

Permanently Attached
p. 68
Handy weld-on/bolt-on clamp for holding
down lids, covers etc. Clamping jaw
opens a full 90° for extra clearance.

800 lbs*

Toggle Bar Clamps

p. 68
Multi-purpose bar clamp, with forged
steel clamping jaw. Order with optional
lower jaw, or attach bar by welding.

800 lbs

64TC (Rev. 11/09

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE PLIERS

CL-50-PL-2
Hex-Head Spindle
and Bottom Cushion

200 lbs CL-50-PL-3

Dual Hex-Head Spindle

CL-50-PL Hex-Head Spindle

Tiny-yet-powerful toggle pliers made of forged steel. 1-inch
jaw width. Supplied with 1/4-20 vinyl-coated hex-head spindle
CL-14208-SA. Optionally available as CL-50-PL-2 with a bot-
tom-jaw cushion, or as CL-50-PL-3 with (2) vinyl-coated hex-
head spindles, CL-14100-SA. Shipping weight 0.4 lbs.
Holding capacity: 200 lbs

350 lbs

CL-150-PL
Medium-size toggle pliers made of forged steel. 1-1/4-inch jaw
width. Supplied with 5/16-18 hex-head spindle CL-516212-SA.
Shipping weight 0.5 lbs.
Holding capacity: 350 lbs

(Rev. 11/09) 65TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE PLIERS

700 lbs

CL-254-PL Swivel-Foot Spindle

Heavy-duty toggle pliers made of forged steel. 1-3/4 inch jaw
width. Two-way quick-release lever for easy opening. Supplied
with 3/8-16 swivel-foot spindle CL-38314-SF. Optionally avail-
able as CL-250-PL with hex-head spindle CL-38314-SA, as CL-
254-PL-2 with (2) hex-head spindles CL-38314-SA, or as CL-
252-PL with flat-cushion spindle CL-38314-FC. Shipping weight
1.3 lbs.
Holding capacity: 700 Lbs

CL-250-PL CL-252-PL CL-254-PL-2

Hex-Head Spindle Flat Cushion Spindle Dual Hex-Head Spindle

66TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

TOGGLE PLIERS

CL-450-PL
Hex-Head Spindle

700 lbs
CL-452-PL
Flat-Cushion Spindle

CL-454-PL Swivel-Foot and Hex-Head Spindles

Wide-jaw heavy-duty toggle pliers made of forged steel. 3-inch jaw
width. Two-way quick-release lever for easy opening. Supplied with
3/8-16 swivel-foot spindle CL-38314-SF and hex-head spindle
CL-38314-SA. Optionally available as CL-450-PL with single hex-
head spindle CL-38314-SA, or as CL-452-PL with a single flat-cush-
ion spindle CL-38314-FC. Shipping weight 1.4 lbs.
Holding capacity: 700 lbs

700 lbs

CL-550-PL
Extra-wide-jaw heavy-duty toggle pliers made of forged steel.
4-1/4-inch jaw width. Two-way quick-release lever for easy open-
ing. Supplied with (2) 3/8-16 hex-head spindles CL-38314-SA.
Shipping weight 1.6 lbs.
Holding capacity: 700 lbs

(Rev. 11/09) 67TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE PLIERS

800 lbs
Stainless Steel

CL-325-PL-S
Handy weld-on/bolt-on stainless steel clamp for holding
down lids, covers, etc. Clamping jaw opens a full 90° for
extra clearance, while handle moves 50°. Supplied with
1/2-13 stainless hex-head spindle CL-12234-SA-S.
Shipping weight 1.0 lbs.
Holding capacity: 800 lbs

800 lbs

CL-345-PL
Multi-purpose bar clamp with forged steel clamping jaw.
Optional lower jaw . . .
Order with optional lower jaw CL-345-PLA, or attach bar by
welding. Jaw opens 84° while handle moves 60°. Supplied
with 3/8-16 swivel-foot spindle CL-38314-SF. Shipping
weight 2.7 lbs.
Holding capacity: 800 lbs
CL-345-PLA

68TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS

FILTER/REGULATOR/LUBRICATOR - CLR-100-FRL

4-WAY AIR VALVE

SHOP AIR CL-14-PCAV
SUPPLY

(2) SILENCERS
CL-14-PCEM
CHECK VALVE - CLR-224-ACV

All Carr Lane toggle clamps are DFARS and RoHS compliant.

Toggle Hold-Down Clamps

pp. 70-74
Similar to a vertical-handle hold-down
clamp, except linkage is operated by a
double-acting air cylinder instead of by
hand. Toggle linkage provides high
holding capacity and insures positive
100 lbs 200 lbs 500 lbs 1000 lbs 5000 lbs mechanical locking even if air pressure
fails.

Toggle Push Clamps

p. 75-76
Similar to a manual plunger clamp,
except linkage is operated by a double-
acting air cylinder instead of by hand.
100 lbs 850 lbs Toggle linkage provides high holding
capacity and insures positive mechani-
cal locking even if air pressure fails.

Swing Clamps
(See SWIFTSURE Catalog)
Hold-down clamp with a clamping arm
that rotates 90° for clear loading. Sturdy
helical-cam mechanism first rotates
arm, then clamps down. Double acting.
14 lbs 25 lbs 66 lbs 100 lbs 165 lbs 277 lbs (Not shown in this catalog section . . .
see SWIFTSURE catalog to order.)

Air Accessories
p. 77
Complete selection of accessories
including clamping valves, check valves,
Clamping Check Exhaust Air Seal
exhaust mufflers, air fittings, and seal
replacement kits.
Valves Valves Mufflers Fittings Replacement Kits

(Rev. 11/09) 69TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS
AIR SUPPLY
FROM ABOVE

AIR SUPPLY
FROM BELOW

100 lbs

Also available with position sensing:

CL-400-PTC
Super-compact hold-down clamp for applications where
space is at a premium. Open arm allows spindle adjust-
ment. Toggle linkage provides high holding capacity and
insures positive mechanical locking even if air pressure
fails. Arm opens 100°. 3/4"-bore double-acting air cylinder
with #10-32 ports (see page 77 to order fittings). Supplied
with #10-32 flat-cushion spindle CL-316112-FC and (2) Please see our web catalog for more information.
CL-3166-TW flanged washers. 100-psi maximum input air
pressure. Shipping weight 0.8 lbs. An optional bracket for
side mounting is also available (CL-400-PCBR).
Holding capacity: 100 lbs
Clamping force at 100 psi, at center of arm: 100 lbs
(4) HOLES 11/64 DIA
FOR #8 OR M4 SCREWS
15/16 7/32
(2) #10-32
PORTS

11/16
3/16 29/32
5/8

3/8
15/16
1-7/8
(4) HOLES 11/64 DIA
FOR #8 OR M4 SCREWS
5/16
5/8 23/32 7/8
7/8 1-11/16
5/8 3/32 1 2-11/32
#10-32 FLAT 1-29/32
CUSHION 3
SPINDLE 4-1/4
OPTIONAL MOUNTING BRACKET
CL-400-PCBR
(ORDER SEPARATELY)

70TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS

200 lbs Also available with position sensing:

Please see our web catalog for more information.

CL-500-PTC
Small-yet-powerful hold-down clamp with a long open arm.
Toggle linkage provides high holding capacity and insures
positive mechanical locking even if air pressure fails. Arm
opens 100°. 1-1/4"-bore double-acting air cylinder with 1/8-
NPT ports. Accepts any 1/4-20 short spindle and (2)
CL-148-TW flanged washers ... see pages 78-82 to order. 100-
psi maximum input air pressure. Shipping weight 2.5 lbs.
Holding capacity: 200 lbs
Clamping force at 100 psi, at center of arm: 200 lbs

(4) HOLES 13/64 DIA

2-1/16 FOR #10 OR M5 SCREWS
1/8
1/4 9/16

1-1/16 1-5/16
DIA
1/8
1/4
1/2 1/8 NPT PORTS

1-3/4
DIA

3/8 2-15/32

1-1/32 1-7/32 1-1/2

13/16
3 2-1/4
2-5/16 3-1/2 2-3/4
9

(Rev. 11/09) 71TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS

Open Arm

Solid Arm
Also available with position sensing:

500 lbs Please see our web catalog for more information.

CL-1000-PTC Open Arm

CL-1001-PTC Solid Arm
Popular medium-size hold-down clamp available with a solid arm, or
an open arm for spindle adjustment. Toggle linkage provides high
holding capacity and insures positive mechanical locking even if
air pressure fails. Arm opens 92°. 1-1/4"-bore double-acting air
cylinder with 1/8-NPT ports. Accepts any 5/16-18 short spindle and
(2) CL-51610-TW flanged washers . . . see pages 78-82 to order.
Solid-arm version accepts a CL-518000-BR bolt retainer. 100-psi
maximum input air pressure. Shipping weight 3.0 lbs.
Holding capacity: 500 lbs
Clamping force at 100 psi, at center of arm: 390 lbs

(4) HOLES 9/32 DIA

3-3/8 FOR 1/4" OR M6 SCREWS
9/32 1/8
21/64

1-1/4 1-5/16
DIA
1/8 IBP

7/16 3/4 1/8" NPT PORTS

1-3/4
DIA

3-1/16
5/8
2-1/16
1-3/8 IBP 1-3/16

1-5/32 2-1/4
IBP
3-5/8
3-19/32 2-25/32
3-1/8
10-1/4

72TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS

Open Arm

Also available with position sensing:

Solid Arm

1000 lbs
Please see our web catalog for more information.

CL-2000-PTC Open Arm

CL-2001-PTC Solid Arm
Extra-large hold-down clamp available with a solid arm, or
an open arm for spindle adjustment. Toggle linkage pro-
vides high holding capacity and insures positive mechani-
cal locking even if air pressure fails. Arm opens 83°. 1-3/4"-
bore double-acting air cylinder with 1/4-NPT ports. Accepts
any 1/2-13 spindle and (2) CL-1213-TW flanged washers . . .
see pages 78-82 to order. Solid-arm version accepts a
CL-113000-BR bolt retainer. 100 psi maximum input air
pressure. Shipping weight 6.0 lbs.
Holding capacity: 1000 lbs
Clamping force at 100 psi, at center of arm 680 lbs

4-15/32
1-13/32 3/16
17/32

1-25/32 1-27/32 DIA

3/16
1/4 NPT PORTS
7/16 1-1/4 (4) HOLES 11/32 DIA
FOR 5/16 OR M8 SCREWS

2-1/2
DIA

7/8
4-3/16
2-5/8
2-3/16 2-21/32

1-11/16 3-1/8
3 3-5/8
5 4-13/32
14-15/32

(Rev. 11/09) 73TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS

5000 lbs

CL-3000-PTC
Heavy-duty hold-down clamp with a solid forged steel
clamping arm. Toggle linkage provides high holding capac-
ity and insures positive mechanical locking even if air pres-
sure fails. Arm opens 83°. 2-1/2"-bore double-acting air
cylinder with 1/4-NPT ports. 150-psi maximum input air
pressure. Shipping weight 15.0 lbs.
Holding capacity: 5000 lbs
Clamping force at 100 psi, at center of arm: 1600 lbs

74TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS

AIR SUPPLY
FROM ABOVE

AIR SUPPLY
FROM BELOW
100 lbs

Also available with position sensing:

CL-600-PPC
Super-compact plunger clamp. Toggle linkage provides
high holding capacity and insures positive mechanical lock-
ing even if air pressure fails. 7/16" plunger travel. 3/4"-bore
double-acting air cylinder with #10-32 ports (see page 77 to
order fittings). Supplied with #8-32 nylon hex-head spindle Please se our web catalog for more information.
CL-832203-SA. 100-psi maximum input air pressure.
Shipping weight 0.8 lbs. An optional bracket for side mount-
ing is also available (CL-400-PCBR).
Holding capacity: 100 lbs
Clamping force at 100 psi: 100 lbs

(3) HOLES 11/64 DIA

1/4 1-1/4 FOR #8 OR M4 SCREWS
DIA 3/8

1-5/16 29/32

5/8 5/16
8-32 THREAD 5/8
1/2 DEEP #10-32 PORTS
7/16 7/16
DIA TRAVEL
15/16
15/32 5/16 1-29/32
23/32 15/16
1/2 1-11/16
1-7/32
1-29/32
1-1/4 2-23/32
(3) HOLES 11/64 DIA 3-3/8
FOR #8 OR M4 SCREWS 4-15/16
OPTIONAL MOUNTING BRACKET
CL-400-PCBR
(ORDER SEPARATELY)

(Rev. 11/09) 75TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS

850 lbs

Also available with position sensing:

CL-1500-PPC
Larger-size plunger clamp. Toggle linkage provides high
holding capacity and insures positive mechanical locking
Please see our web catalog for more information.
even if air pressure fails. 1" plunger travel. 1-1/4"-bore
double-acting air cylinder with 1/8-NPT ports. Accepts any
3/8-16 spindle . . . see pages 78-81 to order. 100-psi max-
imum input air pressure. Shipping weight 3.2 lbs.
Holding capacity: 850 lbs
Clamping force at 100 psi: 430 lbs

(4) HOLES 11/32 DIA

3 FOR 5/16 OR M8 SCREWS
1-5/16 1/8
5/8 29/32
DIA DIA

1-5/16
1-5/8 DIA

IBP
5/16 1/8 NPT PORTS
1-5/8
1-3/4
DIA
1 3/8-16 THREAD
TRAVEL 1-1/8 DEEP 3-3/32

2-3/16

1-3/8 1-3/8
IBP
2-1/2 2-5/8
IBP
3 5-1/16 3-1/8
5-3/8
11-9/16

76TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
AIR-POWERED CLAMPS
CLAMPING VALVES* CHECK VALVES*

CLR-224-ACV
Allows air to flow in one direc-
tion only. 1/4-NPT male x 2.

(2) MOUNTING HOLES

3/4 2 1-3/16
FOR 1/4-20 OR M6 EXHAUST MUFFLERS*
3/8 SCREWS

1-7/8

4-1/4 3-1/8

CL-14-PCAV
Versatile two-position, four-way valve for simple and con- CL-14-PCEM
venient clamp control. Five 1/4-NPT ports. 150 psi maxi- Durable, compact, sintered-
mum pressure. bronze exhaust muffler. 1/4-NPT
male.

AIR FITTINGS*
Quick-Disconnect Adapter Hex Nipple Coupling Tubing Connector
Coupler

CL-14-PCQD
CL-10-PCHN
Both halves, 1/4-NPT female
#10-32 male x 2
CL-14-PCQDS
CL-1014-PCA CL-14-PCHN CL-1810-PCTC
Female socket, 1/4-NPT
#10-32 female x 1/4-NPT male 1/4-NPT male x 2 1/8-OD tube x #10-32 male
female
CL-1418-PCA CL-38-PCHN CL-10-PCCP CL-14-PCTC
CL-14-PCQDP
1/4-NPT female x 1/8-NPT male 3/8-NPT male x 2 #10-32 female x 2 1/4-OD tube x 1/4-NPT male
Male plug, 1/4-NPT female
CL-3814-PCA CL-3814-PCHN CL-14-PCCP (Includes compression
(Industrial Interchange)
3/8-NPT female x 1/4-NPT male 3/8-NPT male x 1/4-NPT male 1/4-NPT female x 2 sleeve and nut)

Street Elbow Banjo Elbow Tee Branch Tee Cross

CL-10-PCTE
CL-14-PCSE CL-10-PCBE #10-32 female x 3 CL-10-PCBT CL-14-PCCR
1/4-NPT female x 1/4-NPT male #10-32 female x #10-32 male CL-14-PCTE #10-32 female x 2, 1/4-NPT female x 4
1/4-NPT female x 3 #10-32 male

* Do not use in high-pressure hydraulic lines.

(Rev. 11/09) 77TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

TOGGLE CLAMP ACCESSORIES

HEX-HEAD SPINDLES

STEEL (USA)

PART NO. A B C D
CL-316112-SA #10-32 1-3/8 5/16 1/8
CL-14112-SA 1-11/16
1/4-20 7/16 3/16
CL-14200-SA 2-3/16
CL-516212-SA 5/16-18 2-11/16 1/2 3/16
CL-38314-SA 3/8-16 3-1/4 9/16 1/4
CL-12314-SA 1/2-13 3-5/16 3/4 5/16
CL-58438-SA 5/8-11 4-3/8 15/16 3/8

VINYL-DIPPED STEEL (USA)

CL-832208-FC #8-32 1-3/16 1/4 1/8
CL-14100-SA 1
1/4-20 7/16 3/16
CL-14208-SA 1-1/2

STAINLESS STEEL (USA)

CL-83234-SA-S 7/8
#8-32 1/4 1/8
CL-832203-SA-S 1-1/8
CL-316100-SA-S #10-32 1-1/8 5/16 1/8
CL-14112-SA-S 1/4-20 1-11/16 7/16 3/16
CL-516200-SA-S 1-15/16
5/16-18 1/2 3/16
CL-516212-SA-S 2-11/16
CL-38212-SA-S 2-1/2
3/8-16 9/16 1/4
CL-38314-SA-S 3-1/4
CL-12234-SA-S 1/2-13 2-13/16 3/4 5/16

NYLON (USA)
CL-832203-SA #8-32 7/8 1/4 1/8
Simple spindle design provides
maximum clamping force.
Fully threaded for maximum
adjustment range. Assembly
includes two jam nuts.
STEEL (METRIC)
Available in thread sizes from
#8-32 to 5/8-11 (M4 to M16 in
PART NO. A B C D
metric).
CLM-530-SA M5 1.32 8mm .14
CLM-640-SA 1.75
M6 10mm .18
CLM-650-SA 2.15
CLM-850-SA 2.19
M8 13mm .22
CLM-865-SA 2.78
CLM-1070-SA M10 3.03 17mm .28
C HEX. CLM-1275-SA M12 3.27 19mm .31
A THREAD IBP CLM-16100-SA M16 4.33 24mm .39

D STAINLESS STEEL (METRIC)

B CLM-416-SA-S .75
M4 7mm .12
CLM-425-SA-S 1.10
CLM-530-SA-S M5 1.32 8mm .14
CLM-640-SA-S 1.75
M6 10mm .18
CLM-650-SA-S 2.15
CLM-850-SA-S 2.19
M8 13mm .22
CLM-865-SA-S 2.78
CLM-1070-SA-S M10 3.03 17mm .28

NYLON (METRIC)
CLM-416-SA M4 .75 7mm .12

78TC (Rev. 11/09)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE CLAMP ACCESSORIES
FLAT-CUSHION SPINDLES
This is the standard spindle supplied with most clamps.
Molded neoprene tip provides medium clamping force with
some compensation for part-size variation. Also provides
scratchfree clamping. Neoprene cushion has a durometer
STEEL (USA)
hardness of 70 shore A, and an operating temperature range
of -40ºF to 220ºF. Spindle is fully threaded for maximum C
adjustment range. Assembly includes two jam nuts. PART NO. A B DIA D E
CL-316112-FC #10-32 1-3/8 9/16 7/16 7/16
CL-14112-FC 1-5/8
1/4-20 5/8 13/32 5/8
CL-14200-FC 2-1/8
CL-518208-FC 5/16-18 2-1/4 3/4 1/2 3/4
CL-516212-FC 3
CL-38212-FC 2-1/2
3/8-16 13/16 5/8 7/8
CL-38314-FC 3-1/2

FLAT-CUSHION SPINDLES (QUICK ADJUSTING)

Same as the Flat-Cushion Spindles above, except with two
knurled nuts, instead of hex jam nuts, for convenient hand
tightening. Use for quick spindle adjustment in applications STEEL (USA)
where high-torque tightening with a wrench is not required.
C
PART NO. A B DIA D E
CL-316112-FCQA #10-32 1-3/8 9/16 7/16 7/16
CL-14112-FCQA 1-5/8
CL-14200-FCQA 1/4-20 2-1/8 5/8 13/32 5/8

! CL-518208-FCQA 2-1/4
NEW
5/16-18 3/4 1/2 3/4
CL-516212-FCQA 3
CL-38212-FCQA 2-1/2
3/8-16 13/16 5/8 7/8
CL-38314-FCQA 3-1/2

POLYURETHANE FLAT CUSHIONS

STAINLESS (USA)
N EW! C D G
PART NO. A B DIA DIA E F DIA
CL-1032-FCP #10-32 .19 .56 .44 .53 .14 .32
A THREAD
B DEEP CL-1420-FCP 1/4-20 .30 .63 .47 .63 .22 .38
CL-51618-FCP 5/16-18 .33 .75 .50 .75 .21 .46
Polyurethane cushions are tougher and G CL-3816-FCP 3/8-16 .38 .81 .63 .88 .21 .52
slightly harder than standard neoprene DIA
cushions. Ideal when greater clamping
force is required while still providing F STAINLESS (METRIC)
scratchfree clamping and some compensa-
tion for part-size variation. Molded-in stain- E C D G
less steel insert provides superior thread PART NO. A B DIA DIA E F DIA
strength. Ideal for making custom-length CLM-5-FCP M5 .19 .56 .44 .53 .14 .32
STAINLESS CLM-6-FCP M6 .24 .63 .47 .63 .22 .38
Flat Cushion Spindles by inserting a thread- STEEL
ed stud. Polyurethane cushion has a hard- D INSERT CLM-8-FCP M8 .30 .75 .50 .75 .21 .46
ness 85 Shore A, operating temperature DIA CLM-10-FCP M10 .35 .81 .63 .88 .21 .52
C
range -90ºF to 200ºF. DIA

(Rev. 7/10) 79TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE CLAMP ACCESSORIES
CONE-CUSHION SPINDLES

Excellent for clamping into drilled holes, slots, or corners.

Molded neoprene tip provides medium clamping force with
some compensation for part-size variation. Also provides
scratchfree clamping. Neoprene cushion has a durometer STEEL (USA)
hardness of 70 shore A, and an operating temperature range
of -40ºF to 220ºF. Spindle is fully threaded for maximum C
adjustment range. Assembly includes two jam nuts. PART NO. A B DIA D
CL-316112-CC #10-32 1-3/8 9/16 7/16
A THREAD CL-14112-CC 1-5/8 5/8
1/4-20 5/8
C DIA CL-14200-CC 2-1/8 5/8
IBP
CL-516212-CC 5/16-18 3 3/4 3/4
70˚
CL-38314-CC 3/8-16 3-1/2 13/16 7/8
D
B

SF SWIVEL-FOOT SPINDLES

Swivel foot provides full contact on uneven or sloped surfaces.

Assembly includes two jam nuts.

STEEL (USA)

C
PART NO. A B DIA D
CL-14112-SF 1-3/4
1/4-20 1/2 3/8
CL-14200-SF 2-1/4
CL-516212-SF 5/16-18 2-3/4 9/16 7/16
CL-38314-SF 3/8-16 3-1/2 5/8 1/2

SSC SWIVEL SCREW CLAMPS

STEEL (USA)
Screw clamp with patented remov- JAM NUT
able, interchangeable swivel foot, PART NO. D
PART NO. (2 REQD) A B C DIA E
available in many sizes and vari-
eties. Add “N” to part no. for delrin CL-23-SSC CL-4-JN 1/4-20 1-19/32 23/64 3/8 1/8
foot, e.g. CL-23-SSCN. See pages CL-27-SSC CL-5-JN 5/16-18 2-3/32 27/64 1/2 5/32
78-79 of the tooling-component CL-43-SSC CL-6-JN 3/8-16 3-1/8 1/2 9/16 3/16
section for additional lengths and CL-44-SSC CL-8-JN 1/2-13 4-1/16 17/32 3/4 3/16
foot options. Order two jam nuts CL-46-SSC CL-10-JN 5/8-11 5-3/64 21/32 15/16 7/32
separately. STEEL (METRIC)
CLM-23-SSC CLM-6-JN M6 1.67 .36 3/8 1/8
CLM-27-SSC CLM-8-JN M8 2.06 .42 1/2 5/32
CLM-32-SSC CLM-10-JN M10 3.08 .62 9/16 3/16
A (THD.) IBP CLM-36-SSC CLM-12-JN M12 4.00 .53 3/4 3/16
CLM-40-SSC CLM-16-JN M16 4.97 .66 15/16 7/32

D 20˚ STAINLESS STEEL (USA)

SWIVEL
CL-23-SSC-S CL-4-JN-S 1/4-20 1-19/32 23/64 3/8 1/8
IBP
E CL-27-SSC-S CL-5-JN-S 5/16-18 2-3/32 27/64 1/2 5/32
C
CL-43-SSC-S CL-6-JN-S 3/8-16 3-1/8 1/2 9/16 3/16
B

80TC (Rev. 7/10)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE CLAMP ACCESSORIES
SL SPRING-LOADED SPINDLES

Clamps with strong spring force to compensate for varying part

thicknesses. Excellent for clamping castings that vary slightly in
size. To install, weld bolt retainer to clamping arm. Assembly
includes two jam nuts, a die spring, and a bolt retainer.

STEEL (USA)
FORCE
D AT "E"
PART NO. A B C MIN MAX E (lbs) F
CL-14200-SL 1/4-20 2-1/4 7/16 1-9/32 1-3/8 1/4 50 5/8
CL-516212-SL 5/16-18 2-3/4 1/2 1-11/16 1-7/8 1/4 100 5/8
CL-38314-SL 3/8-16 3-1/2 9/16 1-3/4 2-9/32 5/16 200 7/8

LIFT YOUR LOAD MA

DE
SAFELY WITH IN
US
CARR LANE HOIST RINGS A
Carr Lane’s lot number marking guarantees
quality by providing traceability for:
NEW! Extra-large Swivel Hoist • Date of manufacture
Rings with our patented EZ-
• Material certification
Torque™ system that allows
tightening several smaller bolt • Magnaflux testing certification
heads with a standard torque • Heat treatment certification
wrench instead of tightening
one large bolt with a special
tool. Swivel Hoist Rings pivot
180 degrees and swivel 360
degrees simultaneously to
allow lifting from any direction. Pivoting hoist rings, swivel hoist rings, side-pull
swivel hoist rings and lifting eyes are some of the
types offered by Carr Lane, ranging from low profile
versions to heavy-duty, extra-large types with load
From large to small, capacities up to 250,000 lbs.
in dozens of types,
Carr Lane has the Visit CarrLane.com and search our
hoist ring for your
application. online catalog for hoist rings
and any of our 100,000 other products.

ISO 9001-2008 CERTIFIED Carr Lane... The Green Team

(Rev. 7/10) 81TC

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377

 E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377
TOGGLE CLAMP ACCESSORIES
TW FLANGED WASHERS
STEEL
C
PART NO. A B DIA
CL-832-TW #8-32 or M4 7/16 15/32
CL-3166-TW #10-32 or M5 1/2 9/16
CL-147-TW 9/16 5/8
1/4-20 or M6
CL-148-TW 19/32 11/16
CL-51610-TW 5/16-18 or M8 3/4 7/8
CL-3811-TW 3/8-16 or M10 15/16 1
Two flanged washers For open-arm clamps. Use two flanged CL-1213-TW 1/2-13 or M12 1-5/32 1-1/4
required per clamp washers to mount spindle, one above the CL-5811-TW 5/8-11or M16 1-3/8 1-15/32
arm and one below. STAINLESS STEEL
A DIA BOLT C
IBP
PART NO. A B DIA
CL-832-TW-S #8-32 or M4 7/16 15/32
IBP CL-3166-TW-S #10-32 or M5 1/2 9/16
B CL-147-TW-S 9/16 5/8
1/4-20 or M6
CL-148-TW-S 19/32 11/16
CL-51610-TW-S 5/16-18 or M8 3/4 7/8
C DIA CL-3811-TW-S 3/8-16 or M10 15/16 1

BR & S BOLT RETAINERS

BR (FOR HTC & VTC CLAMPS)

IBP
SPINDLE A
E SIZE B
PART NO. DIA C D E
A DIA
CL-142000-BR 1/4-20 or M6 9/32 1-1/4 1/2 3/16 3/32
CL-518000-BR 5/16-18 or M8 21/64 1-1/4 5/8 1/4 3/32
D
IBP CL-316000-BR 3/8-16 or M10 17/32 1-1/2 3/4 5/16 1/8
CL-113000-BR 1/2-13 or M12 9/16 1-5/8 7/8 3/8 1/8
C CL-511000-BR 5/8-11 or M16 11/16 1-7/8 1-1/4 3/8 1/8

BR S B S (FOR TC CLAMPS)
For VTC clamps For TC clamps
SPINDLE A B
IBP PART NO. SIZE DIA DIA C
CL-1458-S 1/4-20 or M6 .257 5/8 5/8
B CL-51658-S 5/16-18 or M8 .316 5/8 5/8
For solid-arm clamps. Weld on
bolt retainer at desired arm CL-3878-S 3/8-16 or M10 .397 3/4 7/8
length and spindle angle. A DIA DRILL C

PCBR MOUNTING BRACKETS

(4) HOLES 11/64 DIA
FOR #8 OR M4 SCREWS

5/8

5/16

IBP Downholding Push/Pull

5/8 IBP
15/16 FITS FITS
5/16
15/32 DOWNHOLDING PUSH
PART NO. CLAMPS CLAMPS
CL-150-VTC CL-50-SPC
1/2 CL-400-PCBR
Handy bracket for side-mounting CL-400-PTC CL-600-PPC
small clamps. One reversible bracket
fits several clamps. (3) HOLES 11/64 DIA
FOR #8 OR M4 SCREWS

82TC (Rev. 7/10)

E&E SPECIAL PRODUCTS 7200 MILLER DRIVE, WARREN, MI 48092, 586-978-3377