Scribd
Upload
240 views

Homework Problems 21-28 PDF

This document contains 27 practice problems related to fracture mechanics. The problems cover a range of topics including calculating crack sizes under small-scale yielding conditions, stress-corrosion cracking, fracture of pressure vessels, determining energy release rates using the J-integral and trousers test specimens, and developing the J-integral for small deformations. Experimental methods used by Rivlin and Thomas to determine energy release rates using various test specimens are also discussed.

Uploaded by

ebrahem_sahil5188
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
240 views

Homework Problems 21-28 PDF

This document contains 27 practice problems related to fracture mechanics. The problems cover a range of topics including calculating crack sizes under small-scale yielding conditions, stress-corrosion cracking, fracture of pressure vessels, determining energy release rates using the J-integral and trousers test specimens, and developing the J-integral for small deformations. Experimental methods used by Rivlin and Thomas to determine energy release rates using various test specimens are also discussed.

Uploaded by

ebrahem_sahil5188
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

ES 247 Fracture Mechanics http://imechanica.

org/node/7448 Zhigang Suo


3/12/10 1
Due in class, Thursday, 1 April 2010

21. The small-scale yielding condition
(a) Calculate the maximum permissible crack size in a single-edge-cracked panel subject to a
uniform stress of 140 MPa. The toughness is 50 m MPa , the yield strength is 420 MPa, and
the width of the sample is 0.3 m. (b) Does the situation satisfy the small-scale yielding
condition?

22. Stress-corrosion cracking
A material is susceptible to stress corrosion. The threshold stress intensity factor is
m 0.5 MPa =
th
K . Under a load above this threshold, the crack propagates at a velocity which
obeys a power law

n
BK v = ,
with n = 10. The velocity is m/s 1 0
7
when m 1 MPa = K . The material is subject to a stress of
50 MPa.
(a) Determine the flaw size
th
a , below which the lifetime is infinite.
(b) If the initial flaw size is 1.5
th
a , estimate the lifetime.
(a) If the initial flaw size is 2
th
a , estimate the lifetime.

23. Fracture of a thick-walled pressure vessel
A thick-walled pressure vessel has inner radius r = 10 mm and outer radius R = 40 mm.
A flaw, depth a = 1 mm, is detected on the internal surface of the vessel. The vessel is made of a
steel with a yield strength
Y
o = 2 GPa and a fracture energy
2 3
J/m 1 0 . Estimate the pressure
that the vessel can sustain.

24. A steel has a plane strain toughens of m MPa 00 1 =
c
K and a resistance curve given by

(

|
.
|

\
| A
=
L
a
K K
c R
exp 3 4 ,
where L = 3 mm. A pressure vessel has wall thickness b = 5 cm. An edge crack exists in the wall
of initial length 1 cm. Model the problem as an edge-cracked plate under an applied stress o.
From a handbook we find an expression for the stress intensity factor for a crack of length a:
|
.
|

\
|
=
b
a
F a K t o ,
where
( ) ( ) ( )( )
2 / 3 4
1 265 . 0 85 7 . 0 1 265 . 0

+ + = x x x x F .
(a) Determine the stress
c
o at which the crack starts to advance.
(b) Determine the stress * o at which the crack becomes unstable and the associated crack
advance * a A . Plot the resistance curve and the loading curve on the same diagram.
(c) How large would the tensile yield stress of the steel have to be for small-scale yielding
condition to be valid.

25. The Rivlin-Thomas paper (1953)
Read R.S. Rivlin and A.G. Thomas, Rupture of rubber. I. Characteristic energy for
tearing. Journal of Polymer Science 10, 291-318 (1953). For some of the test-pieces used by
ES 247 Fracture Mechanics http://imechanica.org/node/7448 Zhigang Suo
3/12/10 2
Rivlin and Thomas, they could only determine the energy release rate by experimental
measurements. Carefully describe their experimental method.

26. The trousers test
For the trousers specimen, Rivlin and Thomas (1953) could obtain an analytical
expression of the energy release rate. Carefully derive their result, following the method
described in their paper. Explain how this result is used to determine the fracture energy.

27. The trousers test and the J integral
Obtain the energy release rate for the trousers test by using the J integral.

28. The J integral for small deformation
In class we describe the J integral using the theory of large deformation. Develop the J
integral using the theory of small deformation. A homogeneous, nonlinear elastic material is
characterized by a strain energy density function
( ) ,... ,
22 11
c c W W = ,
such that

( )
ij
ij
W
c
c c
o
c
c
=
, . . . ,
22 11
.
The J-integral is defined as

} |
|
.
|

\
|
c
c
= ds
x
u
n Wn J
i
j ij
1
1
o
(a) Show that the integral vanishes when evaluated over a contour that encloses no singularity.
(b) Consider a crack lying on the x
1
-axis in this material. The crack is loaded remotely, but the
crack surfaces are traction-free. Show that the integral is path-independent when
evaluated over a contour that starts on one crack surface and ends on the other.
(c) When the material is heterogeneous, the J integral is path-dependent. For a heterogeneous
material, show the step that becomes invalid in your proof of (a).

You might also like