Scribd
Upload
199 views

How IDE Controllers Work

Please note that these documents have links to www.howstuffworks.com It does not contain any modifications by myself or any other party. Thus all of them are taken directly from the site including images, and are used for school work by myself and nobody else.. Thank you...

Uploaded by

Mohamed Hussain
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
199 views

How IDE Controllers Work

Please note that these documents have links to www.howstuffworks.com It does not contain any modifications by myself or any other party. Thus all of them are taken directly from the site including images, and are used for school work by myself and nobody else.. Thank you...

Uploaded by

Mohamed Hussain
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

How IDE Controllers Work

by Jeff Tyson
No matter what you do with your computer, storage is an important part of your system. In fact, most
personal computers have one or more of the following storage devices:

• Floppy drive
• Hard drive
• CD-ROM drive

The hard drive and circuit board combination


that typify IDE devices Usually, these devices connect to the
computer through an Integrated Drive Electronics (IDE) interface. Essentially, an IDE interface is a
standard way for a storage device to connect to a computer. IDE is actually not the true technical name
for the interface standard. The original name, AT Attachment (ATA), signified that the interface was
initially developed for the IBM AT computer. In this article, you will learn about the evolution of IDE/ATA,
what the pinouts are and exactly what "slave" and "master" mean in IDE.

IDE Evolution
IDE was created as a way to standardize the use of hard drives in computers. The basic concept
behind IDE is that the hard drive and the controller should be combined. The controller is a small circuit
board with chips that provide guidance as to exactly how the hard drive stores and accesses data.
Most controllers also include some memory that acts as a buffer to enhance hard drive performance.

Before IDE, controllers and hard drives were separate and often proprietary. In other words, a
controller from one manufacturer might not work with a hard drive from another manufacturer. The
distance between the controller and the hard drive could result in poor signal quality and affect
performance. Obviously, this caused much frustration for computer users.
The birth of the IDE interface led to combining a controller like
this one with a hard drive. IBM introduced the AT computer in
1984 with a couple of key innovations.

• The slots in the computer for adding cards used a new version of the Industry Standard
Architecture (ISA) bus. The new bus was capable of transmitting information 16 bits at a time,
compared to 8 bits on the original ISA bus.
• IBM also offered a hard drive for the AT that used a new combined drive/controller. A ribbon
cable from the drive/controller combination ran to an ISA card to connect to the computer,
giving birth to the AT Attachment (ATA) interface.

In 1986, Compaq introduced IDE drives in their Deskpro 386. This drive/controller combination was
based on the ATA standard developed by IBM. Before long, other vendors began offering IDE drives.
IDE became the term that covered the entire range of integrated drive/controller devices. Since almost
all IDE drives are ATA-based, the two terms are used interchangeably.

Controllers, Drives, Host Adapters


Most motherboards come with an IDE interface. This interface is often referred to as an IDE controller,
which is incorrect. The interface is actually a host adapter, meaning that it provides a way to connect
a complete device to the computer (host). The actual controller is on a circuit board attached to the
hard drive. That's the reason it's called Integrated Drive Electronics in the first place!

While the IDE interface was originally


developed for connecting hard drives, it has evolved into the universal interface for connecting internal
floppy drives, CD-ROM drives and even some tape backup drives. Although it is very popular for
internal drives, IDE is rarely used for attaching an external device.

There are several variations of ATA, each one adding to the previous standard and maintaining
backward compatibility.

The standards include:

• ATA-1 - The original specification that Compaq included in the Deskpro 386. It instituted the
use of a master/slave configuration. ATA-1 was based on a subset of the standard ISA 96-pin
connector that uses either 40 or 44 pin connectors and cables. In the 44-pin version, the extra
four pins are used to supply power to a drive that doesn't have a separate power connector.

You might also like