Scribd
Upload
3K views

Valve Body

This document provides instructions for replacing the transmission valve body assembly (U151E/U151F) on a 2005 Highlander. The steps include draining the automatic transmission fluid, removing the transmission oil pan, disconnecting transmission wires, removing the old valve body assembly, installing the new valve body assembly, reconnecting wires, installing the oil pan, and refilling the automatic transmission fluid.

Uploaded by

Pablo Montes
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views

Valve Body

This document provides instructions for replacing the transmission valve body assembly (U151E/U151F) on a 2005 Highlander. The steps include draining the automatic transmission fluid, removing the transmission oil pan, disconnecting transmission wires, removing the old valve body assembly, installing the new valve body assembly, reconnecting wires, installing the oil pan, and refilling the automatic transmission fluid.

Uploaded by

Pablo Montes
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

40-44

AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY (U151E/U151F)

TRANSMISSION VALVE BODY ASSY (U151E/U151F)


400FT-04

REPLACEMENT
1. 2. (a) (b) REMOVE ENGINE UNDER COVER NO.1 DRAIN AUTOMATIC TRANSAXLE FLUID Remove the drain plug and gasket, and drain ATF. Install a new gasket and the drain plug. Torque: 49 Nm (500 kgfcm, 36 ftlbf)

3.

REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSY (a) Remove the 18 bolts, oil pan and gasket. NOTICE: Some fluid will remain in the oil pan. Remove all of the oil pan bolts, and carefully remove the oil pan assembly.

C91925

(b)

Remove the 2 magnets from the oil pan.

D30865

(c)

Examine the particles in the oil pan. (1) Remove the magnets and use them to collect any steel chips. Look at the chips and particles in the pan and on the magnet carefully to see the type of wear which might be found in the transaxle. Steel (magnetic): bearing, gear and plate wear Brass (non-magnetic): bearing wear

AT0103

4. (a) (b)

DISCONNECT TRANSMISSION WIRE Disconnect the 7 shift solenoid valve connectors. Remove the bolt and lock plate, and disconnect the ATF temperature sensor.

C91927

2005 HIGHLANDER REPAIR MANUAL (RM1144U)

Author :

Date :

3230

40-45
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY (U151E/U151F)

5. REMOVE VALVE BODY OIL STRAINER ASSY (a) Remove the 3 bolts and oil strainer. NOTICE: Be careful that some fluid will come out of the oil strainer.

C91931

(b)

Remove the O-ring from the oil strainer.

C91932

6. (a)

REMOVE TRANSMISSION VALVE BODY ASSY Support the valve body assy and remove the 17 bolts and the valve body assy. NOTICE: Be careful not to drop the check valve body, spring and accumulator piston.

C91933

(b)

Remove the check ball body and spring.

F46566

2005 HIGHLANDER REPAIR MANUAL (RM1144U)

Author :

Date :

3231

40-46
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY (U151E/U151F)

(c)

Remove the 5 bolts, 3 lock plates and 7 shift solenoid valves.

D30644

7. (a)

INSTALL TRANSMISSION VALVE BODY ASSY Install the spring and check ball body.

F46566

(b)
B

A B C

Install the 7 shift solenoid valves and 3 lock plates with the 5 bolts. Torque: Bolts A, B: 11 Nm (110 kgfcm, 8 ft.lbf) Bolts C, D: 6.6 Nm (67 kgfcm, 58 in. lbf) Bolt length: Bolt A: 16 mm (0.63 in.) Bolt B: 57 mm (2.2 in.) Bolt C: 20 mm (0.9 in.) Bolt D: 12 mm (0.47 in.)

D30644

2005 HIGHLANDER REPAIR MANUAL (RM1144U)

Author :

Date :

3232

40-47
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY (U151E/U151F)

A B A L C C B B B B C

C L C

C91933

Align the groove of the manual valve with the pin of the lever. (d) Install the 17 bolts. Torque: 11 Nm (110 kgfcm, 8 ftlbf) NOTICE: S Push the valve body against the accumulator piston spring and the check ball body to install it. S First, temporarily tighten those bolts marked by L in the illustration because they are positioning bolts. Bolt length: Bolts A: 25 mm (0.984 in.) Bolts B: 57 mm (2.244 in.) Bolts C: 41 mm (1.614 in.)

(c)

8. (a) (b)

INSTALL VALVE BODY OIL STRAINER ASSY Coat a new O-ring with ATF. Install the O-ring to the oil strainer.

C91932

(c)

Install the oil strainer with the 3 bolts. Torque: 11 Nm (110 kgfcm, 8 ftlbf)

C91931

9. (a) (b)

(c)

CONNECT TRANSMISSION WIRE Coat an O-ring with ATF. Install the ATF temperature sensor with the lock plate and bolt. Torque: 6.6 Nm (67 kgfcm, 58 in.lbf) Connect the 7 shift solenoid valve connectors.

C91927

2005 HIGHLANDER REPAIR MANUAL (RM1144U)

Author :

Date :

3233

40-48
AUTOMATIC TRANSMISSION / TRANS TRANSMISSION VALVE BODY ASSY (U151E/U151F)

10. (a) (b)

Magnet

INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSY Install the 2 magnets to the oil pan. Apply the seal packing or equivalent to the 18 bolts. Seal packing: THREE BOND 1344 or equivalent

D30865

(c)

Install a new gasket, the oil pan and 18 bolts to the transaxle case. Torque: 7.8 Nm (80 kgfcm, 69 in.lbf) NOTICE: Apply seal packing or equivalent to the bolts and tighten them within 10 minutes of application.

C91925

11. 12. 13. 14.

ADD AUTOMATIC TRANSAXLE FLUID INSPECT AUTOMATIC TRANSAXLE FLUID (SEE PAGE 40-2 ) INSTALL ENGINE UNDER COVER NO.1 RESET MEMORY (SEE PAGE 05-1005 )

2005 HIGHLANDER REPAIR MANUAL (RM1144U)

Author :

Date :

3234

You might also like