NATIONAL COMMISSION FOR THE CERTIFICATION OF CRANE OPERATORS (CCO)

RIGGER REFERENCE MANUAL

NCCCO Rigger Reference Manual REV 02/09

Hold Harmless/Release/Disclaimer Agreement The reading and/or using person or entities using this publication for and in consideration of the assistance, cooperation, and information given by the National Commission for the Certification of Crane Operators (NCCCO) in this publication, Rigger Reference Manual, the receipt of which is acknowledged, does hereby and for all future time have released, hold harmless from any liability, and forever discharged for itself, its administrators and assigns the said NCCCO from all and any manner of action or demands whatsoever in law, in admiralty, or in equity, which against the said NCCCO anyone ever had, now have, or which shall be later claimed. This agreement relates specifically to any cause of action arising out of the publication, information provided, subsequent conduct, and any use of the information provided in this publication and related uses or demonstrations of skills, methods, and techniques cite in the publication. This mutually beneficial release and hold harmless agreement may not be changed orally, and exists in perpetuity. NCCCO generally and specifically disclaims any warranty, merchantability of intended or unintended use or liability lifting industry and promote public safety. Copyright 2009 by National Commission for the Certification of Crane Operators. All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, without prior written permission from the publisher. For information, contact the publisher, National Commission for the Certification of Crane Operators, Inc.

Preface

This manual has been provided as a reference source for candidates preparing to take the NCCCO Rigger Certification Exam. The materials contained within have been compiled from a number of different sources. These sources and the relevant material selected for inclusion in the Reference Manual are as follows: ASME B30.10 - Hooks ASME B30.20 - Below-the-Hook Lifting Devices ASME B30.23 - Personnel Lifting Systems OSHA 1910.184 - Slings OSHA 1926.550 - Cranes and Derricks OSHA 1926.251 - Rigging Equipment for Material Handling The material contained herein is not to be used for any other purpose than reference material in association with preparing for the NCCCO exam. No part of this manual is to be copied or used in any manner other than by individual candidates preparing for the NCCCO Rigger examination. Portions reprinted from ASME B30.10, ASME B30.20 and ASME B30.23 by permission of The American Society of Mechanical Engineers. All rights reserved. The following reference materials are used by NCCCOs Examination Committee to verify the accuracy of NCCCO test questions. ASME B30.9 - Slings ASME B30.16 - Hoists ASME B30.26 - Rigging Hardware IPTs Crane and Rigging Training Manual Rigging Handbook - Jerry Klinke 3rd Edition Rigging for Ironworkers Reference Manual NCCCO Rigger Reference Booklet

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

This page intentionally left blank

Table of Contents

ASME B30.10 - Hooks

Section 10-1.1 Markings Section 10-1.2.3 Maintenance

3 5 5 7 9 9 9 9 9 10 10 11 11 13 15 15 15 15 15 17 27 35

ASME B30.20 - Below-the-Hook Lifting Devices

Section 20-1.2.1 Marking Section 20-1.3.2 Every Lift Inspection Section 20-1.3.3 Frequent Inspection Section 20-1.4.1 Operators Section 20-1.4.2 Qualifications Section 20-1.4.3 Conduct of Lifting Device Operators Section 20-1.4.4 Lifting Device Operating Practices Section 20-1.4.5 Miscellaneous Operating Practices Section 20-1.5 Instruction Manuals

ASME B30.23 - Personnel Lifting Systems

Section 23-1.1.1(b)(7) Section 23-1.1.1(b)(10) Section 23-2.1.1 Personnel Lifting Platform Section 23-3.1.3 Ground Crew Section 23-3.2.5 Communications

OSHA 1910.184 - Slings OSHA 1926.251 - Rigging Equipment for Material Handling OSHA 1926.550 - Cranes and Derricks

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

This page intentionally left blank

ASME B30.10-2005 - Hooks

Section 10-1 Markings and Construction

Reprinted from ASME B30.10, by permission of American Society of Mechanical Engineers. All rights reserved.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

This page intentionally left blank

Section 10-1 Markings and Construction

Section 10-1.1 Markings and Construction 10-1.1.1 Markings

Manufacturers identification shall be forged, cast, or die stamped on a low stress and non wearing area of the hook.

10-1.2.3 Maintenance
(a) Any conditions disclosed by the inspections performed in accordance with the requirements of para. 10-1.2.1.2 or 10-1.2.1.3 shall be corrected by repair or replacement before continuing to use the hook. Hooks shall be removed from service unless a qualified person approves their continued use and initiates corrective action. (b) Hooks having damage or wear described as follows shall be repaired or replaced: (1) cracks, nicks, and gouges [see para. 10-1.2.3(e) below] (2) wear exceeding 10% (or as recommended by the manufacturer) of the original sectional dimension (3) any visibly apparent bend or twist from the plane of the unbent hook (4) any distortion causing an increase in throat opening of 5%, not to exceed 14 in (or as recommended by the manufacturer) (5) inability of self-locking hooks to lock (c) A hook latch, when required, that is inoperative shall be repaired or replaced. (d) A hook with a latch that does not close the throat opening shall be removed from service or moused until the latch is replaced or repaired. (e) Repair of cracks, nicks, and gouges shall be carried out by a designated person by grinding longitudinally, following the contour of the hook, provided no dimension is reduced more than 10% (or as recommended by the manufacturer) of its original value. (f ) All other repairs shall be performed by the manufacturer or a qualified person. (g) Replacement parts, such as load pins for clevis hooks, shall be at least equal to the original manufacturers specifications.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

This page intentionally left blank

ASME B30.20-2006 - Below-the-Hook Lifting Devices

Section 20-1 Structural and Mechanical Lifting Devices

Reprinted from ASME B30.20, by permission of American Society of Mechanical Engineers. All rights reserved.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

This page intentionally left blank

Section 20-1 Structural and Mechanical Lifting Devices

Section 20-1.2: Marking, Construction, and Installation 20-1.2.1 Marking (a) Rated Load. The rated load of the lifting device shall be legibly marked on the main structure or on a tag attached to it where it is visible. If the lifting device is made up of several lifters, each detachable from the group, these lifters shall also be marked with their individual rated loads. (b) Identification. All new structural and mechanical lifting devices shall be marked with, but not limited to, the following information: (1) manufacturers name and address (2) serial number (3) lifter weight, if over 100 lb (45 kg) (4) cold current (amps) (when applicable) (5) rated voltage (when applicable) (6) rated load [as described in para. 0-1.2.1(a)] (7) ASME BTH-1 Design Category (8) ASME BTH-1 Service Class Section 20-1.3: Inspection, Testing, and Maintenance 20-1.3.2 Every Lift Inspection Items such as the following shall be inspected by the operator before and/or during every lift for any indication of damage as specifically indicated, including observations during operation for any damage that might occur during the lift: (a) surface of the load for debris (b) condition and operation of the controls (c) condition and operation of the indicators and meters when installed 20-1.3.3 Frequent Inspection Items such as the following shall be inspected for damage at intervals as defined in para. 20-1.3.1(b) (2), including observations during operation for any indications of damage that might appear between inspections. A qualified person shall determine whether any indications of damage constitute a hazard or will require more frequent inspection. For all lifters, inspect: (a) structural members for deformation, cracks, or excessive wear on any part of the lifter (b) loose or missing guards, fasteners, covers, stops, or nameplates (c) all functional operating mechanisms and automatic hold-and-release mechanisms for misadjustments interfering with operation SECTION 20-1.4: OPERATION 20-1.4.1 Operators Below-the-hook lifting devices shall be operated only by trained, designated persons. 20-1.4.2 Qualifications Qualifications for operators of below-the-hook lifting devices are as follows: (a) The operator shall be instructed in the use of the device by a designated person. Instructions should include, but not be limited to, the following: (1) application of the lifter to the load and adjustments, if any, that adapt the lifter to various sizes or kinds of loads (2) instructions in any special operations or precautions (3) the manufacturers suggested operating procedures (4) condition of the load itself required for operation of the lifter, such as, but not limited to, balance, surface cleanliness, flatness, bending, and load thickness (5) storage of the lifter to protect it from damage

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

(6) not exceeding the rated load of the lifting device nor the capacity of the hoisting equipment by the combined weight of the load, the lifting device, and rigging (7) the proper attachment of adapters to lifting device for special load handling (b) The operator shall demonstrate the ability to operate the lifter as instructed before assuming responsibility for using the lifter. 20-1.4.3 Conduct of Lifting Device Operators (a) The operator shall give attention to the operation of the lifts during a lifting sequence. (b) When physically or otherwise unfit, an operator shall not engage in the operation of the equipment. (c) Operators shall be responsible for those operations under their direct control. Whenever there is any doubt as to safety, the operator shall consult a designated person before handling the load. (d) The operator shall respond only to instructions from designated persons. However, the operator shall obey a stop order at all times, no matter who gives it. (e) The operation of the lifter shall be observed before use and during a shift. Any deficiency observed shall be carefully examined by a designated person. If the deficiency constitutes a hazard, the lifter shall be removed from service and tagged Out of Service. Any indication of a hazardous condition shall be reported to a qualified person for evaluation. (f ) The operator shall be familiar with standard hand signals when applicable. (g) The operator shall land any attached load and store the lifter before leaving the lifting device. (h) All controls shall be tested by the operator before use during a shift. If any controls do not operate properly, they should be adjusted or repaired before operations are begun.
10

(i) The operator shall not ride, or allow others to ride, loads or the lifting device. (j) The operator and other personnel shall stay clear of the load. 20-1.4.4 Lifting Device Operating Practices (a) Lifting devices shall be operated only by the following qualified personnel: (1) designated persons (2) trainees under the direct supervision of a designated person (3) maintenance and test personnel, when it is necessary in the performance of their duties (4) inspectors (lifting devices) (b) The lifting device shall not be loaded in excess of its rated load or handle any load for which it is not designed. (c) The lifter shall be applied to the load in accordance with the instruction manual. (d) Before lifting, the operator shall make sure that lifter ropes or chains are not kinked, and that multiple part lines are not twisted around each other. (e) Care should be taken to make certain the load is correctly distributed for the lifter being used. (f ) The temperature of the load should not exceed the maximum allowable limits of the lifter. (g) The lifter shall be brought over the load in such a manner as to minimize swinging. (h) Care shall be taken that there is not sudden acceleration or deceleration of the load. (i) Do not allow load or lifter to come into contact with any obstruction. (j) The operator shall avoid carrying the load over people. (k) The lifter shall not be used for side pulls or sliding the load unless specifically authorized by a qualified person. (l) The operator shall not leave suspended loads unattended.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

20-1.4.5 Miscellaneous Operating Practices (a) An operator shall not use a lifting device that is tagged Out of Service or otherwise designated as nonfunctioning. (b) Out of Service tags on lifting devices shall not be removed without the approval of the person placing them or an authorized person. (c) The lifter, when not in use, should be stored at an assigned location. (d) Caution should be taken that operating markings or tags shall not be removed or defaced. Missing or illegible markings or tags shall be replaced. 20-1.5: INSTRUCTION MANUALS The manufacturer shall provide operating instructions, and maintenance and parts information.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

11

This page intentionally left blank

ASME B30.23-2005 - Personnel Lifting Systems

Section 23-1 Construction and Characteristics Section 23-2 Inspection, Testing, and Maintenance Section 23-3 Operation
Reprinted from ASME B30.23, by permission of American Society of Mechanical Engineers. All rights reserved.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

13

This page intentionally left blank

Section 23-1 Construction and Characteristics

Section 23-1.1 Design 23-1.1.1(b)(7) Personnel Lifting Platform (7) An identification plate shall be located on the platform. The location shall protect against damage and allow easy viewing from both the interior (while hoisted) and exterior (while not hoisted) of the platform. As a minimum, the following information shall be displayed: (a) manufacturer name and address (b) platform rating in terms of weight and personnel (c) platform identification number (d) suspension system description for suspended platforms or the intended hoisting equipment manufacturer identification for boom-attached platforms (e) weight of the empty platform and its suspension system (f ) date of the platform manufacture (g) certification of compliance to the design, construction, and testing requirements of this volume (h) listing of any unique operational environments for which the platform has been designed 23-1.1.1(b)(10) Personnel Lifting Platform (10) For suspended platforms, a suspension system that minimizes the potential for the systems removal and use for other purposes. The suspension system shall be sized by the platform manufacturer, and its installed sling angle established, so as not to cause damage to the platform. Suspension systems shall comply with the following: (e) Synthetic webbing or natural or synthetic fiber rope slings shall not be used for suspension systems. (h) Rope sling and chain sling suspension systems shall have each leg of the system permanently marked with the rated load of the leg. The master link in the system shall be permanently marked with the suspension systems rated load and identification as a personnel lifting platform suspension component. (i) Shackles, if used in the suspension system, shall be of a bolt type with cotter pin. Section 23-2.1 Inspection 23-2.1.1 Personnel Lifting Platform (a) General. The platform manufacturer shall furnish complete inspection criteria for platform users. The criteria shall address all inspection frequency classifications listed in this volume and shall cover (1) the platform (2) rigging components (c) Records (1) For frequent inspections, dated records for the hoisting equipment and personnel platform shall be made and kept by the platform user for the duration of the personnel lift operation. Section 23-3.1 Personnel 23-3.1.3 Ground Crew (a) Qualifications. Individuals assigned as ground crew shall be physically and mentally capable of performing the inspections and operations associated with the lift. They shall be trained in the specific requirements of their tasks associated with the lift. 23-3.2.5 Communications (c) Hand signals shall be posted conspicuously at the following locations: (2) inside the personnel platform

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

15

This page intentionally left blank

OSHA 1910.184 - Slings

OSHA 1910.184 - Slings

Reprinted from Occupational Safety and Health Administration (OSHA). All rights reserved.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

17

This page intentionally left blank

OSHA 1910.184 - Slings

Regulations 1910.184
zz Part Number: zz Part Title: zz Subpart: zz Subpart Title: zz Standard Number: zz Title:
1910.184(a)
Scope. This section applies to slings used in conjunction with other material handling equipment for the movement of material by hoisting, in employments covered by this part. The types of slings covered are those made from alloy steel chain, wire rope, metal mesh, natural or synthetic fiber rope (conventional three strand construction), and synthetic web (nylon, polyester, and polypropylene).

1910 Occupational Safety and Health Standards N Materials Handling and Storage 1910.184 Slings
Cable laid rope is a wire rope composed of six wire
ropes wrapped around a fiber or wire rope core.

Cable laid rope sling-mechanical joint is a wire rope

sling made from a cable laid rope with eyes fabricated by pressing or swaging one or more metal sleeves over the rope junction.

Choker hitch is a sling configuration with one end of the sling passing under the load and through an end attachment, handle or eye on the other end of the sling. Coating is an elastomer or other suitable material applied to a sling or to a sling component to impart desirable properties. Cross rod is a wire used to join spirals of metal mesh to form a complete fabric. (See Fig. N-184-2.) Designated means selected or assigned by the
employer or the employer's representative as being qualified to perform specific duties.

1910.184(b) Definitions Angle of loading is the inclination of a leg or branch

of a sling measured from the horizontal or vertical plane as shown in Fig. N-184-5; provided that an angle of loading of five degrees or less from the vertical may be considered a vertical angle of loading.

Basket hitch is a sling configuration whereby the

sling is passed under the load and has both ends, end attachments, eyes or handles on the hook or a single master link.

Equivalent entity is a person or organization

(including an employer) which, by possession of equipment, technical knowledge and skills, can perform with equal competence the same repairs and tests as the person or organization with which it is equated.

Braided wire rope is a wire rope formed by plaiting

component wire ropes.

Bridle wire rope sling is a sling composed of

multiple wire rope legs with the top ends gathered in a fitting that goes over the lifting hook.

Cable laid endless sling-mechanical joint is a wire rope sling made endless by joining the ends of a single length of cable laid rope with one or more metallic fittings. Cable laid grommet-hand tucked is an endless
wire rope sling made from one length of rope wrapped six times around a core formed by hand tucking the ends of the rope inside the six wraps.
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

Fabric (metal mesh) is the flexible portion of a metal mesh sling consisting of a series of transverse coils and cross rods. Female handle (choker) is a handle with a handle
eye and a slot of such dimension as to permit passage of a male handle thereby allowing the use of a metal mesh sling in a choker hitch. (See Fig. N-184-1.)

Handle is a terminal fitting to which metal mesh fabric

is attached. (See Fig. N-184-1.)

19

Handle eye is an opening in a handle of a metal mesh sling shaped to accept a hook, shackle or other lifting device. (See Fig. N-184-1.) Hitch is a sling configuration whereby the sling is
fastened to an object or load, either directly to it or around it.

Spiral is a single transverse coil that is the basic element from which metal mesh is fabricated. (See Fig. N-184-2.) Strand laid endless sling-mechanical joint is a wire rope sling made endless from one length of rope with the ends joined by one or more metallic fittings. Strand laid grommet-hand tucked is an endless wire rope sling made from one length of strand wrapped six times around a core formed by hand tucking the ends of the strand inside the six wraps. Strand laid rope is a wire rope made with strands
(usually six or eight) wrapped around a fiber core, wire strand core, or independent wire rope core (IWRC).

Link is a single ring of a chain. Male handle (triangle) is a handle with a handle
eye.

Master coupling link is an alloy steel welded coupling link used as an intermediate link to join alloy steel chain to master links. (See Fig. N-184-3.) Master link or gathering ring is a forged or welded
steel link used to support all members (legs) of an alloy steel chain sling or wire rope sling. (See Fig. N-184-3.)

Vertical hitch is a method of supporting a load by a

single, vertical part or leg of the sling. (See Fig. N-1844.)

Mechanical coupling link is a nonwelded, mechanically closed steel link used to attach master links, hooks, etc., to alloy steel chain. FIGURE N-184-1 METAL MESH SLING (TYPICAL) (FOr Figure N-184-1, ClicK Here) FIGURE N-184-2 METAL MESH CONSTRUCTION (FOr Figure N-184-2, ClicK Here) FIGURE N-184-3 MAJOR COMPONENTS OF A QUADRUPLE SLING (FOr Figure N-184-3, ClicK Here) Proof load is the load applied in performance of a
proof test.

1910.184(c) Safe operating practices. Whenever any sling is

used, the following practices shall be observed:

1910.184(c)(1)
Slings that are damaged or defective shall not be used.

1910.184(c)(2)
Slings shall not be shortened with knots or bolts or other makeshift devices.

1910.184(c)(3)
Sling legs shall not be kinked.

Proof test is a nondestructive tension test performed

by the sling manufacturer or an equivalent entity to verify construction and workmanship of a sling.

1910.184(c)(4)
Slings shall not be loaded in excess of their rated capacities.

Rated capacity or working load limit is the

maximum working load permitted by the provisions of this section.

Reach is the effective length of an alloy steel chain

sling measured from the top bearing surface of the upper terminal component to the bottom bearing surface of the lower terminal component.

1910.184(c)(5)
Slings used in a basket hitch shall have the loads balanced to prevent slippage.

1910.184(c)(6)
Slings shall be securely attached to their loads.

Selvage edge is the finished edge of synthetic

webbing designed to prevent unraveling.

Sling is an assembly which connects the load to the

material handling equipment.

1910.184(c)(7)
Slings shall be padded or protected from the sharp edges of their loads.

Sling manufacturer is a person or organization that

assembles sling components into their final form for sale to users.
20

1910.184(c)(8)
Suspended loads shall be kept clear of all obstructions.
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1910.184(c)(9)
All employees shall be kept clear of loads about to be lifted and of suspended loads.

1910.184(e)(3)(i)
In addition to the inspection required by paragraph (d) of this section, a thorough periodic inspection of alloy steel chain slings in use shall be made on a regular basis, to be determined on the basis of (A) frequency of sling use; (B) severity of service conditions; (C) nature of lifts being made; and (D) experience gained on the service life of slings used in similar circumstances. Such inspections shall in no event be at intervals greater than once every 12 months.

1910.184(c)(10)
Hands or fingers shall not be placed between the sling and its load while the sling is being tightened around the load.

1910.184(c)(11)
Shock loading is prohibited.

1910.184(c)(12)
A sling shall not be pulled from under a load when the load is resting on the sling.

1910.184(e)(3)(ii)
The employer shall make and maintain a record of the most recent month in which each alloy steel chain sling was thoroughly inspected, and shall make such record available for examination.

1910.184(d)
Inspections. Each day before being used, the sling and all fastenings and attachments shall be inspected for damage or defects by a competent person designated by the employer. Additional inspections shall be performed during sling use, where service conditions warrant. Damaged or defective slings shall be immediately removed from service.

1910.184(e)(3)(iii)
The thorough inspection of alloy steel chain slings shall be performed by a competent person designated by the employer, and shall include a thorough inspection for wear, defective welds, deformation and increase in length. Where such defects or deterioration are present, the sling shall be immediately removed from service.

1910.184(e)
Alloy steel chain slings.

1910.184(e)(4)
Proof testing. The employer shall ensure that before use, each new, repaired, or reconditioned alloy steel chain sling, including all welded components in the sling assembly, shall be proof tested by the sling manufacturer or equivalent entity, in accordance with paragraph 5.2 of the American Society of Testing and Materials Specification A391-65, which is incorporated by reference as specified in Sec. 1910.6 (ANSI G61.11968). The employer shall retain a certificate of the proof test and shall make it available for examination.

1910.184(e)(1)
Sling identification. Alloy steel chain slings shall have permanently affixed durable identification stating size, grade, rated capacity, and reach.

1910.184(e)(2)
Attachments.

1910.184(e)(2)(i)
Hooks, rings, oblong links, pear shaped links, welded or mechanical coupling links or other attachments shall have a rated capacity at least equal to that of the alloy steel chain with which they are used or the sling shall not be used in excess of the rated capacity of the weakest component.

1910.184(e)(5)
Sling use. Alloy steel chain slings shall not be used with loads in excess of the rated capacities prescribed in Table N-184-1. Slings not included in this table shall be used only in accordance with the manufacturer's recommendations.

1910.184(e)(2)(ii)
Makeshift links or fasteners formed from bolts or rods, or other such attachments, shall not be used.

1910.184(e)(3)
Inspections.
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual 21

1910.184(e)(6)
Safe operating temperatures. Alloy steel chain slings shall be permanently removed from service if they are heated above 1000 deg. F. When exposed to service temperatures in excess of 600 deg. F, maximum working load limits permitted in Table N-184-1 shall be reduced in accordance with the chain or sling manufacturer's recommendations.

1910.184(f)(1)
Sling use. Wire rope slings shall not be used with loads in excess of the rated capacities shown in Tables N-184-3 through N-184-14. Slings not included in these tables shall be used only in accordance with the manufacturers recommendations.

1910.184(f)(2)
Minimum sling lengths.

1910.184(e)(7)
Repairing and reconditioning alloy steel chain slings.

1910.184(f)(2)(i)
Cable laid and 6x19 and 6x37 slings shall have a minimum clear length of wire rope 10 times the component rope diameter between splices, sleeves or end fittings.

1910.184(e)(7)(i)
Worn or damaged alloy steel chain slings or attachments shall not be used until repaired. When welding or heat testing is performed, slings shall not be used unless repaired, reconditioned and proof tested by the sling manufacturer or an equivalent entity.

1910.184(f)(2)(ii)
Braided slings shall have a minimum clear length of wire rope 40 times the component rope diameter between the loops or end fittings.

1910.184(e)(7)(ii)
Mechanical coupling links or low carbon steel repair links shall not be used to repair broken lengths of chain.

1910.184(f)(2)(iii)
Cable laid grommets, strand laid grommets and endless slings shall have a minimum circumferential length of 96 times their body diameter.

1910.184(e)(8)
Effects of wear. If the chain size at any point of any link is less than that stated in Table N-184-2, the sling shall be removed from service.

1910.184(f)(3)
Safe operating temperatures. Fiber core wire rope slings of all grades shall be permanently removed from service if they are exposed to temperatures in excess of 200 deg. F. When nonfiber core wire rope slings of any grade are used at temperatures above 400 deg. F or below minus 60 deg. F, recommendations of the sling manufacturer regarding use at that temperature shall be followed.

1910.184(e)(9)
Deformed attachments.

1910.184(e)(9)(i)
Alloy steel chain slings with cracked or deformed master links, coupling links or other components shall be removed from service. 1910.184(e)(9)(ii) Slings shall be removed from service if hooks are cracked, have been opened more than 15 percent of the normal throat opening measured at the narrowest point or twisted more than 10 degrees from the plane of the unbent hook.

1910.184(f)(4)
End attachments.

1910.184(f)(4)(i)
Welding of end attachments, except covers to thimbles, shall be performed prior to the assembly of the sling.

1910.184(f)
Wire rope slings.

1910.184(f)(4)(ii)
All welded end attachments shall not be used unless proof tested by the manufacturer or equivalent entity at twice their rated capacity prior to initial use. The employer shall retain a certificate of the proof test, and make it available for examination.
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

22

1910.184(f)(5)
Removal from service. Wire rope slings shall be immediately removed from service if any of the following conditions are present:

1910.184(g)(3)(i)
The rated capacity of the sling is not reduced.

1910.184(g)(3)(ii)
The load is evenly distributed across the width of the fabric.

1910.184(f)(5)(i)
Ten randomly distributed broken wires in one rope lay, or five broken wires in one strand in one rope lay.

1910.184(g)(3)(iii)
Sharp edges will not damage the fabric.

1910.184(f)(5)(ii)
Wear or scraping of one-third the original diameter of outside individual wires.

1910.184(g)(4)
Sling coatings. Coatings which diminish the rated capacity of a sling shall not be applied.

1910.184(f)(5)(iii)
Kinking, crushing, bird caging or any other damage resulting in distortion of the wire rope structure.

1910.184(g)(5)
Sling testing. All new and repaired metal mesh slings, including handles, shall not be used unless proof tested by the manufacturer or equivalent entity at a minimum of 1 1/2 times their rated capacity. Elastomer impregnated slings shall be proof tested before coating.

1910.184(f)(5)(iv)
Evidence of heat damage.

1910.184(f)(5)(v)
End attachments that are cracked, deformed or worn.

1910.184(g)(6)
Proper use of metal mesh slings. Metal mesh slings shall not be used to lift loads in excess of their rated capacities as prescribed in Table N-184-15. Slings not included in this table shall be used only in accordance with the manufacturers recommendations.

1910.184(f)(5)(vi)
Hooks that have been opened more than 15 percent of the normal throat opening measured at the narrowest point or twisted more than 10 degrees from the plane of the unbent hook.

1910.184(f)(5)(vii)
Corrosion of the rope or end attachments.

1910.184(g)(7)
Safe operating temperatures. Metal mesh slings which are not impregnated with elastomers may be used in a temperature range from minus 20 deg. F to plus 550 deg. F without decreasing the working load limit. Metal mesh slings impregnated with polyvinyl chloride or neoprene may be used only in a temperature range from zero degrees to plus 200 deg. F. For operations outside these temperature ranges or for metal mesh slings impregnated with other materials, the sling manufacturers recommendations shall be followed.

1910.184(g)
Metal mesh slings --

1910.184(g)(1)
Sling marking. Each metal mesh sling shall have permanently affixed to it a durable marking that states the rated capacity for vertical basket hitch and choker hitch loadings.

1910.184(g)(8)
Repairs.

1910.184(g)(2)
Handles. Handles shall have a rated capacity at least equal to the metal fabric and exhibit no deformation after proof testing.

1910.184(g)(8)(i)
Metal mesh slings which are repaired shall not be used unless repaired by a metal mesh sling manufacturer or an equivalent entity.

1910.184(g)(3)
Attachments of handles to fabric. The fabric and handles shall be joined so that:
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

23

1910.184(g)(8)(ii)
Once repaired, each sling shall be permanently marked or tagged, or a written record maintained, to indicate the date and nature of the repairs and the person or organization that performed the repairs. Records of repairs shall be made available for examination.

1910.184(h)(1)(ii)
Fiber rope slings shall have a diameter of curvature meeting at least the minimums specified in Figs. N-184-4 and N-184-5.

1910.184(h)(1)(iii)
Slings not included in these tables shall be used only in accordance with the manufacturers recommendations. FIGURE N-184-4 Basic Sling COnfiguratiOns With Vertical Legs (FOr Figure N-184-4, ClicK Here) FIGURE N-184-5 Basic Sling COnfiguratiOns With Angled Legs (FOr Figure N-184-5, ClicK Here)

1910.184(g)(9)
Removal from service. Metal mesh slings shall be immediately removed from service if any of the following conditions are present:

1910.184(g)(9)(i)
A broken weld or broken brazed joint along the sling edge.

1910.184(g)(9)(ii)
Reduction in wire diameter of 25 per cent due to abrasion or 15 per cent due to corrosion.

1910.184(h)(5)(vi)
Distortion of hardware in the sling.

1910.184(g)(9)(iii)
Lack of flexibility due to distortion of the fabric.

1910.184(h)(6)
Repairs. Only fiber rope slings made from new rope shall be used. Use of repaired or reconditioned fiber rope slings is prohibited.

1910.184(g)(9)(iv)
Distortion of the female handle so that the depth of the slot is increased more than 10 per cent.

1910.184(i)
Synthetic web slings --

1910.184(g)(9)(v)
Distortion of either handle so that the width of the eye is decreased more than 10 per cent.

1910.184(i)(1)
Sling identification. Each sling shall be marked or coded to show the rated capacities for each type of hitch and type of synthetic web material.

1910.184(g)(9)(vi)
A 15 percent reduction of the original cross sectional area of metal at any point around the handle eye.

1910.184(i)(2)
Webbing. Synthetic webbing shall be of uniform thickness and width and selvage edges shall not be split from the webbings width.

1910.184(g)(9)(vii)
Distortion of either handle out of its plane.

1910.184(h)
Natural and synthetic fiber rope slings --

1910.184(i)(3)
Fittings. Fittings shall be:

1910.184(h)(1)
Sling use.

1910.184(i)(3)(i)
Of a minimum breaking strength equal to that of the sling; and

1910.184(h)(1)(i)
Fiber rope slings made from conventional three strand construction fiber rope shall not be used with loads in excess of the rated capacities prescribed in Tables N-184-16 through N-184-19.
24

1910.184(i)(3)(ii)
Free of all sharp edges that could in any way damage the webbing.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1910.184(i)(4)
Attachment of end fittings to webbing and formation of eyes. Stitching shall be the only method used to attach end fittings to webbing and to form eyes. The thread shall be in an even pattern and contain a sufficient number of stitches to develop the full breaking strength of the sling.

1910.184(i)(8)(i)
Synthetic web slings which are repaired shall not be used unless repaired by a sling manufacturer or an equivalent entity.

1910.184(i)(8)(ii)
Each repaired sling shall be proof tested by the manufacturer or equivalent entity to twice the rated capacity prior to its return to service. The employer shall retain a certificate of the proof test and make it available for examination.

1910.184(i)(5)
Sling use. Synthetic web slings illustrated in Fig. N-184-6 shall not be used with loads in excess of the rated capacities specified in Tables N-184-20 through N-184-22. Slings not included in these tables shall be used only in accordance with the manufacturer's recommendations.

1910.184(i)(8)(iii)
Slings, including webbing and fittings, which have been repaired in a temporary manner shall not be used.

1910.184(i)(6)
Environmental conditions. When synthetic web slings are used, the following precautions shall be taken:

1910.184(i)(9)
Removal from service. Synthetic web slings shall be immediately removed from service if any of the following conditions are present:

1910.184(i)(6)(i)
Nylon web slings shall not be used where fumes, vapors, sprays, mists or liquids of acids or phenolics are present.

1910.184(i)(9)(i)
Acid or caustic burns;

1910.184(i)(6)(ii)
Polyester and polypropylene web slings shall not be used where fumes, vapors, sprays, mists or liquids of caustics are present.

1910.184(i)(9)(ii)
Melting or charring of any part of the sling surface;

1910.184(i)(9)(iii)
Snags, punctures, tears or cuts;

1910.184(i)(6)(iii)
Web slings with aluminum fittings shall not be used where fumes, vapors, sprays, mists or liquids of caustics are present. FIGURE N-184-6 Basic Synthetic Web Sling COnstructiOns

1910.184(i)(9)(iv)
Broken or worn stitches; or

1910.184(i)(9)(v)
Distortion of fittings.

1910.184(i)(7)
Safe operating temperatures. Synthetic web slings of polyester and nylon shall not be used at temperatures in excess of 180 deg. F. Polypropylene web slings shall not be used at temperatures in excess of 200 deg. F.

1910.184(i)(8)
Repairs.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

25

This page intentionally left blank

OSHA 1926.251 - Rigging Equipment for Material Handling

OSHA 1926.251 - Rigging Equipment for Material Handling

Reprinted from Occupational Safety and Health Administration (OSHA). All rights reserved.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

27

This page intentionally left blank

OSHA 1926.251 - Slings

Regulations 1926.251
zz Part Number: zz Part Title: zz Subpart: zz Subpart Title: zz Standard Number: zz Title: zz Applicable Standards: 1926 Safety and Health Regulations for Construction H Materials Handling, Storage, Use, and Disposal 1926.251 Rigging equipment for material handling. 1910.184(a); 1910.184(c)(2); 1910.184(c)(3); 1910.184(c)(5); 1910.184(c)(7); 1910.184(c)(10); 1910.184(c)(11); 1910.184(c)(12); 1910.184(f )(2); 1910.184(f )(3); 1910.184(f )(4); 1910.184(d)
1926.251(a)(5)
"Scope." This section applies to slings used in conjunction with other material handling equipment for the movement of material by hoisting, in employments covered by this part. The types of slings covered are those made from alloy steel chain, wire rope, metal mesh, natural or synthetic fiber rope (conventional three strand construction), and synthetic web (nylon, polyester, and polypropylene).

1926.251(a)
General.

1926.251(a)(1)
Rigging equipment for material handling shall be inspected prior to use on each shift and as necessary during its use to ensure that it is safe. Defective rigging equipment shall be removed from service.

1926.251(a)(2)
Rigging equipment shall not be loaded in excess of its recommended safe working load, as prescribed in Tables H-1 through H-20 in this subpart, following 1926.252(e) for the specific equipment.

1926.251(a)(6)
"Inspections." Each day before being used, the sling and all fastenings and attachments shall be inspected for damage or defects by a competent person designated by the employer. Additional inspections shall be performed during sling use, where service conditions warrant. Damaged or defective slings shall be immediately removed from service.

1926.251(a)(3)
Rigging equipment, when not in use, shall be removed from the immediate work area so as not to present a hazard to employees.

1926.251(a)(4)
Special custom design grabs, hooks, clamps, or other lifting accessories, for such units as modular panels, prefabricated structures and similar materials, shall be marked to indicate the safe working loads and shall be proof-tested prior to use to 125 percent of their rated load.

1926.251(b)
Alloy steel chains.

1926.251(b)(1)
Welded alloy steel chain slings shall have permanently affixed durable identification stating size, grade, rated capacity, and sling manufacturer.

1926.251(b)(2)
Hooks, rings, oblong links, pear-shaped links, welded or mechanical coupling links, or other attachments, when used with alloy steel chains, shall have a rated capacity at least equal to that of the chain.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

29

1926.251(b)(3)
Job or shop hooks and links, or makeshift fasteners, formed from bolts, rods, etc., or other such attachments, shall not be used.

1926.251(c)(2)
Protruding ends of strands in splices on slings and bridles shall be covered or blunted.

1926.251(b)(4)
Rated capacity (working load limit) for alloy steel chain slings shall conform to the values shown in Table H-1.

1926.251(c)(3)
Wire rope shall not be secured by knots, except on haul back lines on scrapers.

1926.251(b)(5)
Whenever wear at any point of any chain link exceeds that shown in Table H-2, the assembly shall be removed from service.

1926.251(c)(4)
The following limitations shall apply to the use of wire rope:

1926.251(c)(4)(i)
An eye splice made in any wire rope shall have not less than three full tucks. However, this requirement shall not operate to preclude the use of another form of splice or connection which can be shown to be as efficient and which is not otherwise prohibited.

1926.251(b)(6)
"Inspections."

1926.251(b)(6)(i)
In addition to the inspection required by other paragraphs of this section, a thorough periodic inspection of alloy steel chain slings in use shall be made on a regular basis, to be determined on the basis of (A) frequency of sling use; (B) severity of service conditions; (C) nature of lifts being made; and (D) experience gained on the service life of slings used in similar circumstances. Such inspections shall in no event be at intervals greater than once every 12 months.

1926.251(c)(4)(ii)
Except for eye splices in the ends of wires and for endless rope slings, each wire rope used in hoisting or lowering, or in pulling loads, shall consist of one continuous piece without knot or splice.

1926.251(c)(4)(iii)
Eyes in wire rope bridles, slings, or bull wires shall not be formed by wire rope clips or knots.

1926.251(b)(6)(ii)
The employer shall make and maintain a record of the most recent month in which each alloy steel chain sling was thoroughly inspected, and shall make such record available for examination.

1926.251(c)(4)(iv)
Wire rope shall not be used if, in any length of eight diameters, the total number of visible broken wires exceeds 10 percent of the total number of wires, or if the rope shows other signs of excessive wear, corrosion, or defect.

1926.251(c)
Wire rope.

1926.251(c)(5)
When U-bolt wire rope clips are used to form eyes, Table H-20 shall be used to determine the number and spacing of clips.

1926.251(c)(1)
Tables H-3 through H-14 shall be used to determine the safe working loads of various sizes and classifications of improved plow steel wire rope and wire rope slings with various types of terminals. For sizes, classifications, and grades not included in these tables, the safe working load recommended by the manufacturer for specific, identifiable products shall be followed, provided that a safety factor of not less than 5 is maintained.

1926.251(c)(5)(i)
When used for eye splices, the U-bolt shall be applied so that the "U" section is in contact with the dead end of the rope.

1926.251(c)(6)
Slings shall not be shortened with knots or bolts or other makeshift devices.
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

30

1926.251(c)(7)
Sling legs shall not be kinked.

1926.251(c)(14)
"Safe operating temperatures." Fiber core wire rope slings of all grades shall be permanently removed from service if they are exposed to temperatures in excess of 200 deg. F (93.33 deg. C). When nonfiber core wire rope slings of any grade are used at temperatures above 400 deg. F (204.44 deg. C) or below minus 60 deg. F (15.55 deg. C), recommendations of the sling manufacturer regarding use at that temperature shall be followed.

1926.251(c)(8)
Slings used in a basket hitch shall have the loads balanced to prevent slippage.

1926.251(c)(9)
Slings shall be padded or protected from the sharp edges of their loads.

1926.251(c)(10)
Hands or fingers shall not be placed between the sling and its load while the sling is being tightened around the load.

1926.251(c)(15)
"End attachments."

1926.251(c)(15)(i)
Welding of end attachments, except covers to thimbles, shall be performed prior to the assembly of the sling.

1926.251(c)(11)
Shock loading is prohibited.

1926.251(c)(15)(ii)
All welded end attachments shall not be used unless proof tested by the manufacturer or equivalent entity at twice their rated capacity prior to initial use. The employer shall retain a certificate of proof test, and make it available for examination.

1926.251(c)(12)
A sling shall not be pulled from under a load when the load is resting on the sling.

1926.251(c)(13)
"Minimum sling lengths."

1926.251(d)
Natural rope, and synthetic fiber-

1926.251(c)(13)(i)
Cable laid and 6 X 19 and 6 X 37 slings shall have minimum clear length of wire rope 10 times the component rope diameter between splices, sleeves or end fittings.

1926.251(d)(1)
General. When using natural or synthetic fiber rope slings, Tables H-15, 16, 17, and 18 shall apply.

1926.251(c)(13)(ii)
Braided slings shall have a minimum clear length of wire rope 40 times the component rope diameter between the loops or end fittings.

1926.251(d)(2)
All splices in rope slings provided by the employer shall be made in accordance with fiber rope manufacturers recommendations.

1926.251(c)(13)(iii)
Cable laid grommets, strand laid grommets and endless slings shall have a minimum circumferential length of 96 times their body diameter.

1926.251(d)(2)(i)
In manila rope, eye splices shall contain at least three full tucks, and short splices shall contain at least six full tucks (three on each side of the center line of the splice).

1926.251(d)(2)(ii)
In layed synthetic fiber rope, eye splices shall contain at least four full tucks, and short splices shall contain at least eight full tucks (four on each side of the center line of the splice).

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

31

1926.251(d)(2)(iii)
Strand end tails shall not be trimmed short (flush with the surface of the rope) immediately adjacent to the full tucks. This precaution applies to both eye and short splices and all types of fiber rope. For fiber ropes under 1-inch diameter, the tails shall project at least six rope diameters beyond the last full tuck. For fiber ropes 1-inch diameter and larger, the tails shall project at least 6 inches beyond the last full tuck. In applications where the projecting tails may be objectionable, the tails shall be tapered and spliced into the body of the rope using at least two additional tucks (which will require a tail length of approximately six rope diameters beyond the last full tuck).

1926.251(d)(4)(ii)
In synthetic fiber rope, eye splices shall consist of at least four full tucks, and short splices shall consist of at least eight full tucks, four on each side of the center line.

1926.251(d)(4)(iii)
Strand end tails shall not be trimmed flush with the surface of the rope immediately adjacent to the full tucks. This applies to all types of fiber rope and both eye and short splices. For fiber rope under 1 inch (2.54 cm) in diameter, the tail shall project at least six rope diameters beyond the last full tuck. For fiber rope 1 inch (2.54 cm) in diameter and larger, the tail shall project at least 6 inches (15.24 cm) beyond the last full tuck. Where a projecting tail interferes with the use of the sling, the tail shall be tapered and spliced into the body of the rope using at lest two additional tucks (which will require a tail length of approximately six rope diameters beyond the last full tuck).

1926.251(d)(2)(iv)
For all eye splices, the eye shall be sufficiently large to provide an included angle of not greater than 60 deg. at the splice when the eye is placed over the load or support.

1926.251(d)(2)(v)
Knots shall not be used in lieu of splices.

1926.251(d)(4)(iv)
Fiber rope slings shall have a minimum clear length of rope between eye splices equal to 10 times the rope diameter.

1926.251(d)(3)
"Safe operating temperatures." Natural and synthetic fiber rope slings, except for wet frozen slings, may be used in a temperature range from minus 20 deg. F (-28.88 deg. C) to plus 180 deg. F (82.2 deg. C) without decreasing the working load limit. For operations outside this temperature range and for wet frozen slings, the sling manufacturer's recommendations shall be followed.

1926.251(d)(4)(v)
Knots shall not be used in lieu of splices.

1926.251(d)(4)(vi)
Clamps not designed specifically for fiber ropes shall not be used for splicing.

1926.251(d)(4)
"Splicing." Spliced fiber rope slings shall not be used unless they have been spliced in accordance with the following minimum requirements and in accordance with any additional recommendations of the manufacturer:

1926.251(d)(4)(vii)
For all eye splices, the eye shall be of such size to provide an included angle of not greater than 60 degrees at the splice when the eye is placed over the load or support.

1926.251(d)(5)
"End attachments." Fiber rope slings shall not be used if end attachments in contact with the rope have sharp edges or projections.

1926.251(d)(4)(i)
In manila rope, eye splices shall consist of at least three full tucks, and short splices shall consist of at least six full tucks, three on each side of the splice center line.

1926.251(d)(6)
"Removal from service." Natural and synthetic fiber rope slings shall be immediately removed from service if any of the following conditions are present:

32

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.251(d)(6)(i)
Abnormal wear.

1926.251(e)(4)(ii)
Free of all sharp edges that could in any way damage the webbing.

1926.251(d)(6)(ii)
Powdered fiber between strands.

1926.251(e)(5)
"Attachment of end fittings to webbing and formation of eyes." Stitching shall be the only method used to attach end fittings to webbing and to form eyes. The thread shall be in an even pattern and contain a sufficient number of stitches to develop the full breaking strength of the sling.

1926.251(d)(6)(iii)
Broken or cut fibers.

1926.251(d)(6)(iv)
Variations in the size or roundness of strands.

1926.251(d)(6)(v)
Discoloration or rotting.

1926.251(e)(6)
"Environmental conditions." When synthetic web slings are used, the following precautions shall be taken:

1926.251(d)(6)(vi)
Distortion of hardware in the sling.

1926.251(e)(6)(i)
Nylon web slings shall not be used where fumes, vapors, sprays, mists or liquids of acids or phenolics are present.

1926.251(e)
Synthetic webbing (nylon, polyester, and polypropylene).

1926.251(e)(1)
The employer shall have each synthetic web sling marked or coded to show:

1926.251(e)(6)(ii)
Polyester and polypropylene web slings shall not be used where fumes, vapors, sprays, mists or liquids of caustics are present.

1926.251(e)(1)(i)
Name or trademark of manufacturer.

1926.251(e)(6)(iii)
Web slings with aluminum fittings shall not be used where fumes, vapors, sprays, mists or liquids of caustics are present.

1926.251(e)(1)(ii)
Rated capacities for the type of hitch.

1926.251(e)(1)(iii)
Type of material.

1926.251(e)(7)
"Safe operating temperatures." Synthetic web slings of polyester and nylon shall not be used at temperatures in excess of 180 deg. F (82.2 deg. C). Polypropylene web slings shall not be used at temperatures in excess of 200 deg. F (93.33 deg. C).

1926.251(e)(2)
Rated capacity shall not be exceeded.

1926.251(e)(3)
"Webbing." Synthetic webbing shall be of uniform thickness and width and selvage edges shall not be split from the webbing's width.

1926.251(e)(8)
"Removal from service." Synthetic web slings shall be immediately removed from service if any of the following conditions are present:

1926.251(e)(4)
"Fittings." Fittings shall be:

1926.251(e)(8)(i)
Acid or caustic burns;

1926.251(e)(4)(i)
Of a minimum breaking strength equal to that of the sling; and
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.251(e)(8)(ii)
Melting or charring of any part of the sling surface;
33

1926.251(e)(8)(iii)
Snags, punctures, tears or cuts;

1926.251(e)(8)(iv)
Broken or worn stitches; or

1926.251(e)(8)(v)
Distortion of fittings.

1926.251(f)
Shackles and hooks.

1926.251(f)(1)
Table H-19 shall be used to determine the safe working loads of various sizes of shackles, except that higher safe working loads are permissible when recommended by the manufacturer for specific, identifiable products, provided that a safety factor of not less than 5 is maintained.

1926.251(f)(2)
The manufacturer's recommendations shall be followed in determining the safe working loads of the various sizes and types of specific and identifiable hooks. All hooks for which no applicable manufacturer's recommendations are available shall be tested to twice the intended safe working load before they are initially put into use. The employer shall maintain a record of the dates and results of such tests.

34

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

OSHA 1926.550 - Cranes and Derricks

OSHA 1926.550 - Cranes and Derricks Reprinted from Occupational Safety and Health
Administration (OSHA). All rights reserved.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

35

This page intentionally left blank

OSHA 1926.550 - Crane and Derricks

Regulations 1926.550
zz Part Number: zz Part Title: zz Subpart: zz Subpart Title: zz Standard Number: zz Title: 1926 Safety and Health Regulations for Construction N Crane, Derricks, Hoists, Elevators, and Conveyors 1926.550 Cranes and Derricks

1926.550(a)
General requirements.

1926.550(a)(5)
The employer shall designate a competent person who shall inspect all machinery and equipment prior to each use, and during use, to make sure it is in safe operating condition. Any deficiencies shall be repaired, or defective parts replaced, before continued use.

1926.550(a)(1)
The employer shall comply with the manufacturers specifications and limitations applicable to the operation of any and all cranes and derricks. Where manufacturers specifications are not available, the limitations assigned to the equipment shall be based on the determinations of a qualified engineer competent in this field and such determinations will be appropriately documented and recorded. Attachments used with cranes shall not exceed the capacity, rating, or scope recommended by the manufacturer.

1926.550(a)(6)
A thorough, annual inspection of the hoisting machinery shall be made by a competent person, or by a government or private agency recognized by the U.S. Department of Labor. The employer shall maintain a record of the dates and results of inspections for each hoisting machine and piece of equipment.

1926.550(a)(2)
Rated load capacities, and recommended operating speeds, special hazard warnings, or instruction, shall be conspicuously posted on all equipment. Instructions or warnings shall be visible to the operator while he is at his control station.

1926.550(a)(7)
Wire rope shall be taken out of service when any of the following conditions exist:

1926.550(a)(7)(i)
In running ropes, six randomly distributed broken wires in one lay or three broken wires in one strand in one lay;

1926.550(a)(3)
[Reserved]

1926.550(a)(4)
Hand signals to crane and derrick operators shall be those prescribed by the applicable ANSI standard for the type of crane in use. An illustration of the signals shall be posted at the job site.

1926.550(a)(7)(ii)
Wear of one-third the original diameter of outside individual wires. Kinking, crushing, bird caging, or any other damage resulting in distortion of the rope structure;

1926.550(a)(7)(iii)
Evidence of any heat damage from any cause;

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

37

1926.550(a)(7)(iv)
Reductions from nominal diameter of more than onesixty-fourth inch for diameters up to and including five-sixteenths inch, one-thirty-second inch for diameters three-eighths inch to and including one-half inch, three-sixty-fourths inch for diameters ninesixteenths inch to and including three-fourths inch, one-sixteenth inch for diameters seven-eighths inch to 1 1/8 inches inclusive, three-thirty-seconds inch for diameters 1 1/4 to 1 1/2 inches inclusive;

1926.550(a)(12)
All windows in cabs shall be of safety glass, or equivalent, that introduces no visible distortion that will interfere with the safe operation of the machine.

1926.550(a)(13) 1926.550(a)(13)(i)
Where necessary for rigging or service requirements, a ladder, or steps, shall be provided to give access to a cab roof.

1926.550(a)(7)(v)
In standing ropes, more than two broken wires in one lay in sections beyond end connections or more than one broken wire at an end connection.

1926.550(a)(13)(ii)
Guardrails, handholds, and steps shall be provided on cranes for easy access to the car and cab, conforming to American National Standards Institute B30.5.

1926.550(a)(7)(vi)
Wire rope safety factors shall be in accordance with American National Standards Institute B 30.5-1968 or SAE J959-1966.

1926.550(a)(13)(iii)
Platforms and walkways shall have anti-skid surfaces.

1926.550(a)(14)
Fuel tank filler pipe shall be located in such a position, or protected in such manner, as to not allow spill or overflow to run onto the engine, exhaust, or electrical equipment of any machine being fueled.

1926.550(a)(8)
Belts, gears, shafts, pulleys, sprockets, spindles, drums, fly wheels, chains, or other reciprocating, rotating, or other moving parts or equipment shall be guarded if such parts are exposed to contact by employees, or otherwise create a hazard. Guarding shall meet the requirements of the American National Standards Institute B 15.1-1958 Rev., Safety Code for Mechanical Power Transmission Apparatus.

1926.550(a)(14)(i)
An accessible fire extinguisher of 5BC rating, or higher, shall be available at all operator stations or cabs of equipment.

1926.550(a)(9)
Accessible areas within the swing radius of the rear of the rotating superstructure of the crane, either permanently or temporarily mounted, shall be barricaded in such a manner as to prevent an employee from being struck or crushed by the crane.

1926.550(a)(14)(ii)
All fuels shall be transported, stored, and handled to meet the rules of Subpart F of this part. When fuel is transported by vehicles on public highways, Department of Transportation rules contained in 49 CFR Parts 177 and 393 concerning such vehicular transportation are considered applicable.

1926.550(a)(10)
All exhaust pipes shall be guarded or insulated in areas where contact by employees is possible in the performance of normal duties.

1926.550(a)(15)
Except where electrical distribution and transmission lines have been deenergized and visibly grounded at point of work or where insulating barriers, not a part of or an attachment to the equipment or machinery, have been erected to prevent physical contact with the lines, equipment or machines shall be operated proximate to power lines only in accordance with the following:

1926.550(a)(11)
Whenever internal combustion engine powered equipment exhausts in enclosed spaces, tests shall be made and recorded to see that employees are not exposed to unsafe concentrations of toxic gases or oxygen deficient atmospheres.
38

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.550(a)(15)(i)
For lines rated 50 kV. or below, minimum clearance between the lines and any part of the crane or load shall be 10 feet;

1926.550(a)(15)(vii)(a)
The equipment shall be provided with an electrical ground directly to the upper rotating structure supporting the boom; and

1926.550(a)(15)(ii)
For lines rated over 50 kV., minimum clearance between the lines and any part of the crane or load shall be 10 feet plus 0.4 inch for each 1 kV. over 50 kV., or twice the length of the line insulator, but never less than 10 feet;

1926.550(a)(15)(vii)(b)
Ground jumper cables shall be attached to materials being handled by boom equipment when electrical charge is induced while working near energized transmitters. Crews shall be provided with nonconductive poles having large alligator clips or other similar protection to attach the ground cable to the load.

1926.550(a)(15)(iii)
In transit with no load and boom lowered, the equipment clearance shall be a minimum of 4 feet for voltages less than 50 kV., and 10 feet for voltages over 50 kV., up to and including 345 kV., and 16 feet for voltages up to and including 750 kV.

1926.550(a)(15)(vii)(c)
Combustible and flammable materials shall be removed from the immediate area prior to operations.

1926.550(a)(15)(iv)
A person shall be designated to observe clearance of the equipment and give timely warning for all operations where it is difficult for the operator to maintain the desired clearance by visual means;

1926.550(a)(16)
No modifications or additions which affect the capacity or safe operation of the equipment shall be made by the employer without the manufacturers written approval. If such modifications or changes are made, the capacity, operation, and maintenance instruction plates, tags, or decals, shall be changed accordingly. In no case shall the original safety factor of the equipment be reduced.

1926.550(a)(15)(v)
Cage-type boom guards, insulating links, or proximity warning devices may be used on cranes, but the use of such devices shall not alter the requirements of any other regulation of this part even if such device is required by law or regulation;

1926.550(a)(17)
The employer shall comply with Power Crane and Shovel Association Mobile Hydraulic Crane Standard No. 2.

1926.550(a)(15)(vi)
Any overhead wire shall be considered to be an energized line unless and until the person owning such line or the electrical utility authorities indicate that it is not an energized line and it has been visibly grounded;

1926.550(a)(18)
Sideboom cranes mounted on wheel or crawler tractors shall meet the requirements of SAE J743a-1964.

1926.550(a)(15)(vii)
Prior to work near transmitter towers where an electrical charge can be induced in the equipment or materials being handled, the transmitter shall be de-energized or tests shall be made to determine if electrical charge is induced on the crane. The following precautions shall be taken when necessary to dissipate induced voltages:

1926.550(a)(19)
All employees shall be kept clear of loads about to be lifted and of suspended loads.

1926.550(b)
Crawler, locomotive, and truck cranes.

1926.550(b)(1)
All jibs shall have positive stops to prevent their movement of more than 5 deg above the straight line of the jib and boom on conventional type crane booms. The use of cable type belly slings does not constitute compliance with this rule.
39

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.550(b)(2)
All crawler, truck, or locomotive cranes in use shall meet the applicable requirements for design, inspection, construction, testing, maintenance and operation as prescribed in the ANSI B30.5-1968, Safety Code for Crawler, Locomotive and Truck Cranes. However, the written, dated, and signed inspection reports and records of the monthly inspection of critical items prescribed in section 5-2.1.5 of the ANSI B30.5-1968 standard are not required. Instead, the employer shall prepare a certification record which includes the date the crane items were inspected; the signature of the person who inspected the crane items; and a serial number, or other identifier, for the crane inspected. The most recent certification record shall be maintained on file until a new one is prepared.

1926.550(d)(1)
The rated load of the crane shall be plainly marked on each side of the crane, and if the crane has more than one hoisting unit, each hoist shall have its rated load marked on it or its load block, and this marking shall be clearly legible from the ground or floor.

1926.550(d)(2)
Bridge trucks shall be equipped with sweeps which extend below the top of the rail and project in front of the truck wheels.

1926.550(d)(3)
Except for floor-operated cranes, a gong or other effective audible warning signal shall be provided for each crane equipped with a power traveling mechanism.

1926.550(c)
Hammerhead tower cranes.

1926.550(d)(4)
All overhead and gantry cranes in use shall meet the applicable requirements for design, construction, installation, testing, maintenance, inspection, and operation as prescribed in the ANSI B30.2.0-1967, Safety Code for Overhead and Gantry Cranes.

1926.550(c)(1)
Adequate clearance shall be maintained between moving and rotating structures of the crane and fixed objects to allow the passage of employees without harm.

1926.550(c)(2)
Each employee required to perform duties on the horizontal boom of hammerhead tower cranes shall be protected against falling by guardrails or by a personal fall arrest system in conformance with subpart M of this part.

1926.550(e)
Derricks. All derricks in use shall meet the applicable requirements for design, construction, installation, inspection, testing, maintenance, and operation as prescribed in American National Standards Institute B30.6-1969, Safety Code for Derricks.

1926.550(c)(3)
Buffers shall be provided at both ends of travel of the trolley.

1926.550(f) Floating cranes and derricks 1926.550(f)(1)

Mobile cranes mounted on barges.

1926.550(c)(4)
Cranes mounted on rail tracks shall be equipped with limit switches limiting the travel of the crane on the track and stops or buffers at each end of the tracks.

1926.550(f)(1)(i)
When a mobile crane is mounted on a barge, the rated load of the crane shall not exceed the original capacity specified by the manufacturer.

1926.550(c)(5)
All hammerhead tower cranes in use shall meet the applicable requirements for design, construction, installation, testing, maintenance, inspection, and operation as prescribed by the manufacturer.

1926.550(f)(1)(ii)
A load rating chart, with clearly legible letters and figures, shall be provided with each crane, and securely fixed at a location easily visible to the operator.

1926.550(d)
Overhead and gantry cranes.
40 National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.550(f)(1)(iii)
When load ratings are reduced to stay within the limits for list of the barge with a crane mounted on it, a new load rating chart shall be provided.

1926.550(g)(1)(ii)(A)
"Failure" means load refusal, breakage, or separation of components.

1926.550(f)(1)(iv)
Mobile cranes on barges shall be positively secured.

1926.550(g)(1)(ii)(B)
"Hoist" (or hoisting) means all crane or derrick functions such as lowering, lifting, swinging, booming in and out or up and down, or suspending a personnel platform.

1926.550(f)(2)
Permanently mounted floating cranes and derricks.

1926.550(f)(2)(i)
When cranes and derricks are permanently installed on a barge, the capacity and limitations of use shall be based on competent design criteria.

1926.550(g)(1)(ii)(C)
"Load refusal" means the point where the ultimate strength is exceeded.

1926.550(g)(1)(ii)(D)
"Maximum intended load" means the total load of all employees, tools, materials, and other loads reasonably anticipated to be applies to a personnel platform or personnel platform component at any one time.

1926.550(f)(2)(ii)
A load rating chart with clearly legible letters and figures shall be provided and securely fixed at a location easily visible to the operator.

1926.550(f)(2)(iii)
Floating cranes and floating derricks in use shall meet the applicable requirements for design, construction, installation, testing, maintenance, and operation as prescribed by the manufacturer.

1926.550(g)(1)(ii)(E)
"Runway" means a firm, level surface designed, prepared and designated as a path of travel for the weight and configuration of the crane being used to lift and travel with the crane suspended platform. An existing surface may be used as long as it meets these criteria.

1926.550(f)(3)
Protection of employees working on barges. The employer shall comply with the applicable requirements for protection of employees working onboard marine vessels specified in 1926.605.

1926.550(g)(2)
General requirements. The use of a crane or derrick to hoist employees on a personnel platform is prohibited, except when the erection, use, and dismantling of conventional means of reaching the worksite, such as a personnel hoist, ladder, stairway, aerial lift, elevating work platform or scaffold, would be more hazardous or is not possible because of structural design or worksite conditions.

1926.550(g)
Crane or derrick suspended personnel platforms -

1926.550(g)(1)
Scope, application and definitions -

1926.550(g)(3)
Cranes and derricks -

1926.550(g)(1)(i)
Scope and application. This standard applies to the design, construction, testing, use and maintenance of personnel platforms, and the hoisting of personnel platforms on the load lines of cranes or derricks.

1926.550(g)(3)(i)
Operational criteria.

1926.550(g)(1)(ii)
Definitions. For the purposes of this paragraph (g), the following definitions apply:

1926.550(g)(3)(i)(A)
Hoisting of the personnel platform shall be performed in a slow, controlled, cautious manner with no sudden movements of the crane or derrick, or the platform.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

41

1926.550(g)(3)(i)(B)
Load lines shall be capable of supporting, without failure, at least seven times the maximum intended load, except that where rotation resistant rope is used, the lines shall be capable of supporting without failure, at least ten times the maximum intended load. The required design factor is achieved by taking the current safety factor of 3.5 (required under 1926.550(b)(2) and applying the 50 per cent derating of the crane capacity which is required by 1926.550(g)(3)(i)(F).

1926.550(g)(3)(ii)(C)
A positive acting device shall be used which prevents contact between the load block or overhaul ball and the boom tip (anti-two-blocking device), or a system shall be used which deactivates the hoisting action before damage occurs in the event of a two-blocking situation (two-block damage prevention feature).

1926.550(g)(3)(ii)(D)
The load line hoist drum shall have a system or device on the power train, other than the load hoist brake, which regulates the lowering rate of speed of the hoist mechanism (controlled load lowering.) Free fall is prohibited.

1926.550(g)(3)(i)(C)
Load and boom hoist drum brakes, swing brakes, and locking devices such as pawls or dogs shall be engaged when the occupied personnel platform is in a stationary position.

1926.550(g)(4)
Personnel Platforms. -

1926.550(g)(3)(i)(D)
The crane shall be uniformly level within one percent of level grade and located on firm footing. Cranes equipped with outriggers shall have them all fully deployed following manufacturer's specifications, insofar as applicable, when hoisting employees.

1926.550(g)(4)(i)
Design criteria.

1926.550(g)(4)(i)(A)
The personnel platform and suspension system shall be designed by a qualified engineer or a qualified person competent in structural design.

1926.550(g)(3)(i)(E)
The total weight of the loaded personnel platform and related rigging shall not exceed 50 percent of the rated capacity for the radius and configuration of the crane or derrick.

1926.550(g)(4)(i)(B)
The suspension system shall be designed to minimize tipping of the platform due to movement of employees occupying the platform.

1926.550(g)(3)(i)(F)
The use of machines having live booms (booms in which lowering is controlled by a brake without aid from other devices which slow the lowering speeds) is prohibited.

1926.550(g)(4)(i)(C)
The personnel platform itself, except the guardrail system and personnel fall arrest system anchorages, shall be capable of supporting, without failure, its own weight and at least five times the maximum intended load. Criteria for guardrail systems and personal fall arrest system anchorages are contained in subpart M of this Part.

1926.550(g)(3)(ii)
Instruments and components.

1926.550(g)(3)(ii)(A)
Cranes and derricks with variable angle booms shall be equipped with a boom angle indicator, readily visible to the operator.

1926.550(g)(4)(ii)
Platform specifications.

1926.550(g)(3)(ii)(B)
Cranes with telescoping booms shall be equipped with a device to indicate clearly to the operator, at all times, the boom's extended length or an accurate determination of the load radius to be used during the lift shall be made prior to hoisting personnel.
42

1926.550(g)(4)(ii)(A)
Each personnel platform shall be equipped with a guardrail system which meets the requirements of Subpart M, and shall be enclosed at least from the toeboard to mid-rail with either solid construction or expanded metal having openings no greater than 1/2 inch (1.27 cm).
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.550(g)(4)(ii)(B)
A grab rail shall be installed inside the entire perimeter of the personnel platform.

1926.550(g)(4)(iii)(B)
The number of employees occupying the personnel platform shall not exceed the number required for the work being performed.

1926.550(g)(4)(ii)(C)
Access gates, if installed, shall not swing outward during hoisting.

1926.550(g)(4)(iii)(C)
Personnel platforms shall be used only for employees, their tools and the materials necessary to do their work, and shall not be used to hoist only materials or tools when not hoisting personnel.

1926.550(g)(4)(ii)(D)
Access gates, including sliding or folding gates, shall be equipped with a restraining device to prevent accidental opening.

1926.550(g)(4)(iii)(D)
Materials and tools for use during a personnel lift shall be secured to prevent displacement.

1926.550(g)(4)(ii)(E)
Headroom shall be provided which allows employees to stand upright in the platform.

1926.550(g)(4)(iii)(E)
Materials and tools for use during a personnel lift shall be evenly distributed within the confines of the platform while the platform is suspended.

1926.550(g)(4)(ii)(F)
In addition to the use of hard hats, employees shall be protected by overhead protection on the personnel platform when employees are exposed to falling objects.

1926.550(g)(4)(iv)
Rigging.

1926.550(g)(4)(ii)(G)
All rough edges exposed to contact by employees shall be surfaced or smoothed in order to prevent injury to employees from punctures or lacerations.

1926.550(g)(4)(iv)(A)
When a wire rope bridle is used to connect the personnel platform to the load line, each bridle leg shall be connected to a master link or shackle in such a manner to ensure that the load is evenly divided among the bridle legs.

1926.550(g)(4)(ii)(H)
All welding of the personnel platform and its components shall be performed by a qualified welder familiar with the weld grades, types and material specified in the platform design.

1926.550(g)(4)(iv)(B)
Hooks on overhaul ball assemblies, lower load blocks, or other attachment assemblies shall be of a type that can be closed and locked, eliminating the hook throat opening. Alternatively, an alloy anchor type shackle with a bolt, nut and retaining pin may be used.

1926.550(g)(4)(ii)(I)
The personnel platform shall be conspicuously posted with a plate or other permanent marking which indicates the weight of the platform, and its rated load capacity or maximum intended load.

1926.550(g)(4)(iv)(C)
Wire rope, shackles, rings, master links, and other rigging hardware must be capable of supporting, without failure, at least five times the maximum intended load applied or transmitted to that component. Where rotation resistant rope is used, the slings shall be capable of supporting without failure at least ten times the maximum intended load.

1926.550(g)(4)(iii)
Personnel platform loading.

1926.550(g)(4)(iii)(A)
The personnel platform shall not be loaded in excess of its rated load capacity, When a personnel platform does not have a rated load capacity then the personnel platform shall not be loaded in excess of its maximum intended load.
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.550(g)(4)(iv)(D)
All eyes in wire rope slings shall be fabricated with thimbles.
43

1926.550(g)(4)(iv)(E)
Bridles and associated rigging for attaching the personnel platform to the hoist line shall be used only for the platform and the necessary employees, their tools and the materials necessary to do their work and shall not be used for any other purpose when not hoisting personnel.

1926.550(g)(5)(iii)(D)
The hoisting system shall be inspected if the load rope is slack to ensure all ropes are properly stated on drums and in sheaves.

1926.550(g)(5)(iv)
A visual inspection of the crane or derrick, rigging, personnel platform, and the crane or derrick base support or ground shall be conducted by a competent person immediately after the trial lift to determine whether the testing has exposed any defect or produced any adverse effect upon any component or structure.

1926.550(g)(5)
Trial lift, inspections and proof testing.

1926.550(g)(5)(i)
A trial lift with the unoccupied personnel platform loaded at least to the anticipated lift weight shall be made from ground level, or any other location where employees will enter the platform to each location at which the personnel platform is to be hoisted and positioned. This trial lift shall be performed immediately prior to placing personnel on the platform. The operator shall determine that all systems, controls and safety devices are activated and functioning properly; that no interferences exist; and that all configurations necessary to reach those work locations will allow the operator to remain under the 50 percent limit of the hoist's rated capacity. Materials and tools to be used during the actual lift can be loaded in the platform, as provided in paragraphs (g)(4)(iii)(D), and (E) of this section for the trial lift. A single trial lift may be performed at one time for all locations that are to be reached from a single set up position.

1926.550(g)(5)(v)
Any defects found during inspections which create a safety hazard shall be corrected before hoisting personnel.

1926.550(g)(5)(vi)
At each job site, prior to hoisting employees on the personnel platform, and after any repair or modification, the platform and rigging shall be proof tested to 125 percent of the platform's rated capacity by holding it in a suspended position for five minutes with the test load evenly distributed on the platform (this may be done concurrently with the trial lift). After proof testing, a competent person shall inspect the platform and rigging. Any deficiencies found shall be corrected and another proof test shall be conducted. Personnel hoisting shall not be conducted until the proof testing requirements are satisfied.

1926.550(g)(5)(ii)
The trial lift shall be repeated prior to hoisting employees whenever the crane or derrick is moved and set up in a new location or returned to a previously used location. Additionally , the trial lift shall be repeated when the lift route is changed unless the operator determines that the route change is not significant (i.e. the route change would not affect the safety of hoisted employees.)

1926.550(g)(6)
Work practices.

1926.550(g)(6)(i)
Employees shall keep all parts of the body inside the platform during raising lowering, and positioning. This provision does not apply to an occupant of the platform performing the duties of a signal person.

1926.550(g)(5)(iii)
After the trial lift, and just prior to hoisting personnel, the platform shall be hoisted a few inches and inspected to ensure that it is secure and properly balanced. Employees shall not be hoisted unless the following conditions are determined to exist:

1926.550(g)(6)(ii)
Before employees exit or enter a hoisted personnel platform that is not landed, the platform shall be secured to the structure where the work is to be performed, unless securing to the structure creates an unsafe situation.

1926.550(g)(5)(iii)(A)
Hoist ropes shall be free of kinks;

1926.550(g)(6)(iii)
Tag lines shall be used unless their use creates an unsafe condition.

1926.550(g)(5)(iii)(B)
Multiple part lines shall not be twisted around each other;

1926.550(g)(6)(iv)
The crane or derrick operator shall remain at the controls at all times when the crane engine is running and the platform is occupied.
National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

1926.550(g)(5)(iii)(C)
The primary attachment shall be centered over the platform, and
44

1926.550(g)(6)(v)
Hoisting of employees shall be promptly discontinued upon indication of any dangerous weather conditions or other impending danger.

1926.550(g)(7)(ii)(D)
A complete trial run shall be performed to test the route of travel before employees are allowed to occupy the platform. This trial run can be performed at the same time as the trial lift required by paragraph (g)(5) (i) of this section which tests the route of the lift.

1926.550(g)(6)(vi)
Employees being hoisted shall remain in continuous sight of and in direct communication with the operator or signal person. In those situations where direct visual contact with the operator is not possible, and the use of a signal person would create a greater hazard for the person, direct communication alone such as by radio may be used.

1926.550(g)(7)(ii)(E)
If travel is done with a rubber tired-carrier, the condition and air pressure of the tires shall be checked. The chart capacity for lifts on rubber shall be used for application of the 50 percent reduction of rated capacity. Notwithstanding paragraph (g)(5)(i)(E) of this section, outriggers may be partially retracted as necessary for travel.

1926.550(g)(6)(vii)
Except over water, employees occupying the personnel platform shall use a body belt/harness system with lanyard appropriately attached to the lower load block or overhaul ball, or to a structural member within the personnel platform capable of supporting a fall impact for employees using the anchorage. When working over water the requirements of 1926.106 shall apply.

1926.550(g)(8)
Pre-lift meeting.

1926.550(g)(8)(i)
A meeting attended by the crane or derrick operator, signal person(s) (if necessary for the lift), employee(s) to be lifted, and the person responsible for the task to be performed shall be held to review the appropriate requirements of paragraph (g) of this section and the procedures to be followed.

1926.550(g)(6)(viii)
No lifts shall be made on another of the crane's or derrick's loadlines while personnel are suspended on a platform.

1926.550(g)(7)
Traveling.

1926.550(g)(8)(ii)
This meeting shall be held prior to the trial lift at each new work location, and shall be repeated for any employees newly assigned to the operation. [44 FR 8577, Feb. 9, 1979; 44 FR 20940, Apr. 6, 1979, as amended at 52 FR 36382, Sept. 28, 1987; 53 FR 29139, Aug. 2, 1988; 54 FR 15406, Apr. 18, 1989; 54 FR 24334, June 7, 1989; 58 FR 35183, June 30, 1993, 59 FR 40730, Aug. 9, 1994; 61 FR 5507, Feb. 13, 1996]

1926.550(g)(7)(i)
Hoisting of employees while the crane is traveling is prohibited, except for portal, tower and locomotive cranes, or where the employer demonstrates that there is no less hazardous way to perform the work.

1926.550(g)(7)(ii)
Under any circumstances where a crane would travel while hoisting personnel, the employer shall implement the following procedures to safeguard employees:

1926.550(g)(7)(ii)(A)
Crane travel shall be restricted to a fixed track or runway;

1926.550(g)(7)(ii)(B)
Travel shall be limited to the load radius of the boom used during the lift; and

1926.550(g)(7)(ii)(C)
The boom must be parallel to the direction of travel.

National Commission for the Certification of Crane Operators 2009 Rigger Reference Manual

45

IMPORTANT CONTACT INFORMATION

NATIONAL COMMISSION FOR THE CERTIFICATION OF CRANE OPERATORS
2750 Prosperity Avenue, Suite 505 Fairfax, VA 22031-4312 Phone: 703-560-2391 Fax: 703-560-2392 E-Mail: [email protected]

INTERNATIONAL ASSESSMENT INSTITUTE

Attention: CCO Testing 600 Cleveland Street, Suite 900 Clearwater, Florida 33755 Phone: 727-449-8525 Fax: 727-461-2746

NATIONAL COMMISSION FOR THE CERTIFICATION OF CRANE OPERATORS

2750 Prosperity Avenue, Suite 505 Fairfax, VA 22031 - 4312 Phone: 703-560-2391 Fax: 703-560-2392 [email protected]