High Temperature

Industrial VRS Magnetic Speed Sensors

DESCRIPTION High Temperature VRS sensors are designed for use in applications where the sensor is exposed to temperatures up to 260 C [450 F]. Sealed Front-End versions are available for applications where the sensor is exposed to fluids, lubricants or adverse environmental conditions. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensors pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. FEATURES Self-powered operation Direct conversion of actuator speed to output frequency Simple installation No moving parts Designed for use over a wide range of speeds Adaptable to a wide variety of configurations Customized VRS products for unique speed sensing applications Housing diameters: 5/8 in (M16), 3/8 in (M12), 1/4 in (8M) Housing material/style: stainless steel threaded Terminations: MS3106 connector, preleaded Output voltages: 4.7 Vp-p to 125 Vp-p The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensors pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave if viewed on an oscilloscope. Honeywell also offers VRS sensors for general purpose, high output, power output, high resolution and hazardous location applications, as well as low-cost molded OEM versions.

POTENTIAL APPLICATIONS Engine RPM (revolutions per minute) measurement on aircraft, automobiles, boats, buses, trucks and rail vehicles Motor RPM measurement on drills, grinders, lathes and automatic screw machines Motor RPM measurement on precision camera, tape recording and motion picture equipment Process speed measurement on food, textile, paper, woodworking, printing, tobacco and pharmaceutical industry machinery Motor speed measurement of electrical generating equipment Speed measurement of pumps, blowers, mixers, exhaust and ventilating fans Flow measurement on turbine meters Wheel-slip measurement on autos and locomotives Gear speed measurement

High Temperature
5/8 INCH (M16*) SENSORS (All dimensions for reference only. mm/[in]) *Contact Honeywell for availability of metric mounting thread versions. LOW RESISTANCE COILS FOR HIGH FREQUENCY APPLICATIONS General Specifications Parameter Characteristic Min. output voltage 25 Vp-p Coil resistance Pole piece diameter Min. surface speed Operating temp. range Mounting thread Catalog Listing 3010HTB 65 Ohm typ. 2,69 mm [0.106 in] 0,50 m/s [20 in/s] typ. -55 C to 230 C [-67 F to 450 F] 5/8-18 UNF-2A Parameter Inductance Gear pitch range Characteristic 30 mH max.

Test Condition Specifications Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance

24 DP (module 1.06) or coarser Optimum actuator 20 DP (module 1.27) 50 kHz typ. N/A MS3106 connector

Max. operating frequency Vibration Termination

Weight 70 g [2.5 oz]

HIGH RESISTANCE COILS FOR MAXIMUM OUTPUT VOLTAGE APPLICATIONS General Specifications Parameter Characteristic Min. output voltage 125 Vp-p Coil resistance Pole piece diameter Min. surface speed Operating temp. range Mounting thread Catalog Listing 3030HTB 3030HTB25 1055 Ohm typ. 2,69 mm [0.106 in] 0,25 m/s [10 in/s] typ. -55 C to 230 C [-67 F to 450 F] 5/8-18 UNF-2A Weight 70 g [2.5 oz] 84 g [3.0 oz] Parameter Inductance Gear pitch range Optimum actuator Max. operating frequency Vibration Termination Characteristic 450 mH max. 24 DP (module 1.06) or coarser 20 DP (module 1.27) 15 kHz typ. N/A MS3106 connector

Test Condition Specifications Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance

Thread Length (A) 28 mm [1.1 in] 63 mm [2.5 in]

www.honeywell.com/sensing

Industrial VRS Magnetic Speed Sensors

5/8 INCH (M16*) SENSORS CONTINUED (All dimensions for reference only. mm/[in]) *Contact Honeywell for availability of metric mounting thread versions. NOMINAL RESISTANCE COILS FOR LOW IMPEDANCE LOAD APPLICATIONS General Specifications Parameter Characteristic Min. output voltage 45 Vp-p Coil resistance Pole piece diameter Min. surface speed Operating temp. range Mounting Thread Catalog Listing 3040HTB 3040HTB25 141 Ohm typ. 4,75 mm [0.187 in] 0,38 m/s [15 in/s] typ. -55 C to 230 C [-67 F to 450 F] 5/8-18 UNF-2A Weight 70 g [2.5 oz] 84 g [3.0 oz] Parameter Inductance Gear pitch range Optimum actuator Max. operating frequency Vibration Termination Characteristic 85 mH max. 12 DP (module 2.11) or coarser 8 DP (module 3.17) 40 kHz typ. N/A MS3106 Connector

Test Condition Specifications Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 8 DP (module 3.17) Air gap 0,127 mm [0.005 in] Load 1.25 kOhm resistance

Thread Length (A) 28 mm [1.1 in] 63 mm [2.5 in]

Honeywell Sensing and Control

High Temperature
5/8 INCH SEALED FRONT-END SENSORS (All dimensions for reference only. mm/[in]) (No metric available.) NOMINAL RESISTANCE COILS FOR LOW IMPEDANCE LOADS APPLICATIONS General Specifications Parameter Min. output voltage Coil resistance Pole piece diameter Min. surface speed Operating temp. range Mounting Thread Catalog Listing MA243HT Characteristic 60 Vp-p 120 Ohm to 162 Ohm 4,39 mm [0.173 in] 0,38 m/s [15 in/s] typ. -54 C to 220 C [-65 F to 428 F] 5/8-18 UNF-2A Weight 98 g [3.5 oz] Parameter Inductance Gear pitch range Optimum actuator Max. operating frequency Vibration Termination Characteristic 85 mH max. 12 DP (module 2.11) or coarser 8 DP (module 3.17) 40 kHz typ. N/A MS3106 connector

Test Condition Specifications Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 8 DP (module 3.17) Air gap 0,127 mm [0.005 in] Load 1.25 kOhm resistance

www.honeywell.com/sensing

Industrial VRS Magnetic Speed Sensors

3/8 INCH (M12*) SENSORS (All dimensions for reference only. mm/[in]) *Contact Honeywell for availability of metric mounting thread versions. General Specifications Parameter Min. output voltage Coil resistance Pole piece diameter Min. surface speed Operating temp. range Mounting thread Characteristic 15 Vp-p 110 Ohm max. 2,36 mm [0.093 in] 0,75 m/s [20 in/s] typ. -40 C to 205 C [-40 F to 400 F] 3/8-24 UNF-2A Parameter Inductance Gear pitch range Characteristic 31 mH max. Test Condition Specifications Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance

26 DP (module 0.98) or coarser Optimum actuator 24 DP (module 1.06) ferrous metal gear Max. operating 50 kHz typ. frequency N/A 24 AWG Tefloninsulated leads

Vibration Termination

Catalog Listing 3015HTB 3015HTB15

Thread Length (A) 20 mm [0.8 in] 38 mm [1.5 in]

Weight 28 g [1.0 oz] 42 g [1.5 oz]

Honeywell Sensing and Control

High Temperature
1/4 INCH (M8*) MINIATURE SENSORS (All dimensions for reference only. mm/[in]) *Contact Honeywell for availability of metric mounting thread versions. General Specifications Parameter Characteristic Parameter Inductance Gear pitch range Optimum actuator Max. operating frequency Vibration Termination Characteristic 13 mH max. 36 DP (module 0.70) or coarser 28 DP (Module 0.90) ferrous metal gear 70 kHz typ. Mil-Std 202F Method 204D 30 AWG TeflonInsulated Leads Min. output voltage 4.7 Vp-p Coil resistance Pole piece diameter Min. surface speed Operating temp. range Mounting thread 137 Ohm max. 1 mm [0.040 in] 0,89 m/s [35 in/s] typ. -40 C to 230 C [-40 F to 450 F] 1/4-40 UNS-2A Test Condition Specifications Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear Air gap Load resistance 20 DP (module 1.27) 0,127 mm [0.005 in] 100 kOhm

Catalog Listing 3055A

Weight 14 g [0.5 oz]

www.honeywell.com/sensing

Industrial VRS Magnetic Speed Sensors

1/4 INCH SEALED FRONT-END SENSORS (All dimensions for reference only. mm/[in]) (No metric available.) General Specifications Parameter Characteristic Min. output voltage 5.2 Vp-p Coil resistance 20 Ohm to 45 Ohm Parameter Inductance Gear pitch range Optimum actuator Max. operating frequency Vibration Termination Characteristic 85 mH max. 36 DP (module 0.70) or coarser 28 DP (module 0.90) ferrous metal gear 70 kHz typ. Mil-Std 202F Method 204D 28 AWG Tefloninsulated leads Test Condition Specifications Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance

Pole piece 1 mm [0.040 in] diameter Min. surface speed 0,89 m/s [35 in/s] typ. Operating temp. range Mounting Thread -73 C to 230 C [-100 F to 450 F] 1/4-40 UNS-2A

Catalog Listing MA3055

Weight 28 g [1 oz]

Catalog Listing MA3055S10

Weight 28 g [1 oz]

Honeywell Sensing and Control

WARNING
PERSONAL INJURY
DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury.

WARNING
MISUSE OF DOCUMENTATION
The information presented in this product sheet is for reference only. Do not use this document as a product installation guide. Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury.

WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywells standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace, at its option, without charge those items it finds defective. The foregoing is buyers sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use.

SALES AND SERVICE Honeywell serves its customers through a worldwide network of sales offices, representatives and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office or: E-mail: [email protected] Internet: www.honeywell.com/sensing Phone and Fax:
Asia Pacific Europe +65 6355-2828 +65 6445-3033 Fax +44 (0) 1698 481481 +44 (0) 1698 481676 Fax Latin America +1-305-805-8188 +1-305-883-8257 Fax USA/Canada +1-800-537-6945 +1-815-235-6847 +1-815-235-6545 Fax

Automation and Control Solutions Sensing and Control Honeywell 1985 Douglas Drive North Minneapolis, MN 55422 www.honeywell.com/sensing
005877-1-EN IL50 GLO Printed in USA March 2007 Copyright 2007 Honeywell International Inc. All rights reserved.