Scribd
Upload
93 views

Pattern Allowances

Pattern allowances are extra material added to patterns to account for shrinkage during solidification and cooling of metals. For cast iron the shrinkage allowance is 1% and for aluminum it is about 1.6%. Additional machining allowance of 1.5-2.5mm is provided if the casting will later be machined. Draft allowance is added to patterns to facilitate easy removal from the sand mould, usually at an angle of 2-3 degrees on vertical surfaces. Patterns are usually made of wood but metal patterns may be used for large production runs.

Uploaded by

Quanta Boson
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
93 views

Pattern Allowances

Pattern allowances are extra material added to patterns to account for shrinkage during solidification and cooling of metals. For cast iron the shrinkage allowance is 1% and for aluminum it is about 1.6%. Additional machining allowance of 1.5-2.5mm is provided if the casting will later be machined. Draft allowance is added to patterns to facilitate easy removal from the sand mould, usually at an angle of 2-3 degrees on vertical surfaces. Patterns are usually made of wood but metal patterns may be used for large production runs.

Uploaded by

Quanta Boson
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

PATTERN ALLOWANCES

Since most metals shrink in volume, when solidifying from liquid state and again on cooling, it is obvious, that the pattern should be made slightly larger than the size of finished casting. This difference in size of the pattern is called shrinkage allowance. For cast iron, this allowance is 1% and for aluminium, it a; about 1.6%. On many occasions, castings produced in the foundry shop are machined subsequently. The object of machining is to get exact sizes and better surface finish on the component. If such is the case, a layer of 1.52.5 mm thick material has to be provided all round the casting. This is done by making the pattern suitably bigger than the casting. This increase in size of pattern is called "machining allowance. Another important allowance provided on patterns is called draft allowance. It facilitates withdrawal of pattern from the mould. It is provided on vertical surfaces. The idea is to give an inclination of 2-3 degrees to vertical surfaces, so that while lifting the pattern, the upper surface is wider and withdrawing the pattern with draft provided will not damage the sand mould. On inner vertical
surfaces, draft is provided in such a way that top surface is narrower and bottom portion of pattern is wider. Apart from the above allowances, some other allowances are sometimes given

to compensate for inherent distortion or bending of castings. Sharp corners and bends are also radiusized while making a pattern. Patterns are usually made of good quality wood. Wood is
easy to work, acquires good smooth surface and properly seasoned wood retains its size. It is

also reiatively cheap and abundant. However, if a very large number of castings are required, metal patterns may be used. Usually, they are made of aluminium~magnesium alloys. TYPES OF PATTERNS (i) Solid or single piece pattern: Such patterns are made in one piece and are suitable only for very simple castings. There is no provision for runners and risers etc. Moulding can be done either in the foundry floor (called pit moulding) or in a moulding box. There is no difficulty in withdrawing the pattern from the mould as the broadest portion of the pattern is at the top. As an example, if a cylindrical pin with a circular head has to be cast, a one piece pattern shown in Fig. 1 will be adequate.
Direction 01 withdrawing T pattern from mould
Fig. 1 : Solid Pattern

(ii) Split pattern: I; is not practical to have one piece for parts Of shapes. because it would not be possible to withdraw the pattern from the mould.

You might also like