Scribd
Upload
222 views

13 Heat Integration in A Crude Distillation Unit Using Pinch Analysis Concepts

This document summarizes the results of several case studies evaluating heat integration opportunities in a crude distillation unit using pinch analysis concepts. In the first case study, moving heat duty from below to above the pinch point reduced utility costs with minimal impact on capital costs. The second case study found that moving the pinch point by adding a new product draw did not provide benefits due to high capital costs. However, adjusting stream flow rates lowered capital costs. The third case study showed that lower return temperatures on pumparound sections (lower flows) increase capital costs. Overall, appropriately varying process streams based on thermodynamic insights can improve heat integration and design optimization.

Uploaded by

xinghust
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
222 views

13 Heat Integration in A Crude Distillation Unit Using Pinch Analysis Concepts

This document summarizes the results of several case studies evaluating heat integration opportunities in a crude distillation unit using pinch analysis concepts. In the first case study, moving heat duty from below to above the pinch point reduced utility costs with minimal impact on capital costs. The second case study found that moving the pinch point by adding a new product draw did not provide benefits due to high capital costs. However, adjusting stream flow rates lowered capital costs. The third case study showed that lower return temperatures on pumparound sections (lower flows) increase capital costs. Overall, appropriately varying process streams based on thermodynamic insights can improve heat integration and design optimization.

Uploaded by

xinghust
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 29

Heat Integration in a Crude Distillation Unit Using Pinch Analysis Concepts

(AIChE 2008 Spring Meeting 165b)

PETROBRAS R&D Center CENPES


Antonio V. S. de Castro*, M.Sc. Carlos Ney da Fonseca Claudio L. M. Kuboski Silvia Waintraub, M.Sc. Washington de O. Geraldelli, Ph.D.

Introduction Higher prices of energy and oil Crude Distillation Unit:


Energy-intensive Process Heat Integration Fractionation Constraints

Pumparound Design
Number of Pumparound Sections Location of Pumparound Sections Pumparound Section Heat Duty

Outline for Simulation Approach


Design procedure:
Location of pumparounds (PA) Analyse Pumparound Duty concerning the Fractionation constraints Evaluate alternatives to improve Heat Recovery: global costs (Pinch Design Method)
Evaluate PA heat duty distribution at atmospheric tower (vacuum constant) Evaluate changing pinch stream possibilities by process modifications (modify vacuum tower configuration, considering atmospheric tower best result fixed) Evaluate modifying pinch stream return temperature (if PA)

Pumparound Section Heat Recovery at higher temperature Maximum heat recoverable Heat of vaporization of the liquid from the tray above the pumparound section Trade-off:
n Pumparound Duty p Fractionation above the pumparound

Fractionation Quality:
Internal reflux Gap and Overlap

Pumparound Section
Max Heat Duty at PA:
Zero Internal Liquid Reflux above PA return.

By Simulation:
Internal Liquid Reflux above PA return Enthalpy Difference at bubble and dew point; Simulate the tower specifying near Zero Internal Reflux above PA, varying PA duty.

In all studies, products specification were a target. However, stripping steam optimization was not part of this present work.

Sketch

LVGO NAPHTHA TPA KEROSENE MPA LIGHT DIESEL HVGO BPA HEAVY DIESEL SLOP WAX MVGO

REDUCED CRUDE

VACUUM RESIDUE

Pumparound Section - Example


0 0 500 1000 1500 2000 2500 3000 3500 4000 4500
100 0 150 200 250 300 350 400

Flow rate (kmol/h)

Temperature ( C)

10

10

Theoretical stage

15

Theoretical stage

15

20

20

25

25

Liquid Internal Reflux - Max PA


30
30

Temperature - Max PA Temperature

Liquid Internal Reflux

35

35

These graphics compare both liquid internal reflux and temperature profile at atmospheric column, considering BPA is already defined. Data refering to Max PA are at near zero liquid reflux, while the other data refer to maximum liquid internal reflux above Mid PA section.

Simulation Basis
19o API Brazilian Crude Kept Constant:
Atm Furnace Outlet Temperature Vacuum Furnace Outlet Temperature Atm Ovhd Drum Temperature Overflash Rate Number of stages

HVGO / LVGO ~ 1 Pumparound Withdraw at Product Drawoff Pans Fractionation Constraints:


Naphtha Kerosene: 0 oC min gap Kerosene Light Diesel: 5 oC min gap Light Diesel Heavy Diesel: 30 oC max overlap

Cost basis: Brent: US$ 30.00 / bbl Fuel oil: US$ 20.60 / 106 kcal Cooling water: US$ 0.066 / m3 Equipment Cycle Life: 10 years

Fractionation vs Heat Recovery


Gap between side products
20

10

-10 30 C Overlap at 6x106 kcal/h -20 GAP5-95 Kerosene vs Naphtha -30 GAP5-95 Light Diesel vs Kerosene GAP5-95 Heavy Diesel vs Light Diesel -40 d(Gap HDxLD)/d(BPA Duty) Gap 5-95 (oC) -25

-50

-60

-70 0 -5 -10 -15 -20 Bottom Pum paround Duty (106 kcal/h)

Fractionation vs Heat Recovery


Gap between side products
20

10

0 5 C gap at 18x106 kcal/h Gap 5-95 (oC) Inflection Point at Duty = 17x106 kcal/h -40 0 -5 -10 -15 -20 -25 -30 -35 Mid Pum paround Duty (106 kcal/h)

GAP5-95 Kerosene vs Naphtha


-10

GAP5-95 Light Diesel vs Kerosene GAP5-95 Heavy Diesel vs Light Diesel d(Gap LD x K)/d(MPA Duty)

-20

-30 Inf lection Point at Duty = 14x106 kcal/h

Fractionation vs Heat Recovery


Gap between side products
20

10 0 C gap at 17x106 kcal/h 0 GAP5-95 Kerosene vs Naphtha Gap 5-95 (oC) -20 -25 GAP5-95 Light Diesel vs Kerosene GAP5-95 Heavy Diesel vs Light Diesel -10 d(Gap N x K)/d(TPA Duty) Inflection Point at Duty = 18x106 kcal/h

-20

Inflection Point at Duty = 12x106 kcal/h -30

-40 0 -5 -10 -15 Top Pum paround Duty (106 kcal/h)

Case Study 1

Case Study 1 max heat recovery


Evaluate PA heat duty distribution in atmospheric tower (vacuum configuration constant)
Duties in 106 kcal/h
Base Case Ovhd Condenser Top PA Mid PA Bottom PA Overall 58.8 0 0 0 58.8 16,20,0 22.7 16 20 0 58.7 16,14,6 23.0 16 14 6 59.0

Results Case Study 1

BASE

16,20,0

16,14,6

Results Case Study 1

Atmospheric Tower
Duties in 106 kcal/h
Base Hot Utility Cold Utility Hot Utility (Base) 9.79 66.1 0 16,20,0 10.01 64.7 + 0.22 16,14,6 5.74 60.4 - 4.05

Case 16,14,6: C; Treturn = 303 C Bottom PA: 6x106 kcal/h; Tout = 338 Pinch: HVGO; Tpinch = 312 C Bottom PA: Above the Pinch = 338 312 = 26 C (74,3%) 6 x 0,743 = 4,45x106 kcal/h ~ 4,27x106 kcal/h (4.05 + 0.22)

Results Case Study 1

Atmospheric Tower
Base T optimum (C) Utility Cost (106 US$/yr) Capital Cost (106 US$/yr) Overall Cost (106 US$/yr) Savings (106 US$/yr) 26.2 8.504 6.016 14.520 0 16,20,0 14.9 7.014 6.126 13.140 1.380 16,14,6 19.2 6.644 5.789 12.432 2.088

* For Case 16,20,0 at T =19.2 C Capital Cost = 5.637x106 US$/yr slightly lower than Case 16,14,6 caused by lower approach near pinch region, but process recovery lead to much lower Utility Cost

Case Study 2

Vacuum Tower MVGO Draw


In case study 1: benefit on moving duty from below to above the pinch What about moving the pinch by changing process/configuration, keeping specification? LVGO LVGO
MVGO HVGO HVGO

Add MVGO draw HVGO : MVGO : LVGO ~ 1 : 4 : 1 (case: MVGO) High flow rate required to change pinch location. Atmospheric column configuration constant (best result previously achieved). process to process recovery above pinch Hot and cold utility approach - Capital cost (trade-off)

Results Case Study 2

16,14,6

MVGO

Results Case Study 2


16,14,6 Hot Utility at pinch (106 kcal/h) Cold Utility at pinch (106 kcal/h) Hot Utility (Base) (106 kcal/h) T optimum (C) Utility Cost (106 US$/yr) Capital Cost (106 US$/yr) Overall Cost (106 US$/yr) Savings (106 US$/yr) 5.74 60.4 - 4.05 19.2 6.644 5.789 12.432 2.088 MVGO (pinch Mid PA) 0.16 54.1 -9.63 13.2 4.565 8.555 13.120 1.400

As pinch is occurring at MVGO (much higher flow rate than HVGO), there is a large portion of Hot Composite Curve with few variation in flow above the pinch, resulting expressive increment on Capital Cost (penalty too high).

Results Case Study 2


Add MVGO withdraw didnt present good results, but : If products flow rates change? HVGO : MVGO : LVGO ~ 1 : 2 : 2 T HVGO PA Return = 285 C Named: Case MVGO 285 HVGO kept as pinch stream (same process recovery than Case 16,14,6) Higher approach (hot x cold composite) Capital Cost decrease
MVGO 285 result only evaluating HEN (capital cost of tower changes not included)

Results Case Study 2

16,14,6

MVGO

MVGO 285

Results Case Study 2


16,14,6 Hot Utility at pinch (106 kcal/h) Cold Utility at pinch (106 kcal/h) Hot Utility (Base) (106 kcal/h) T optimum (C) Utility Cost (106 US$/yr) Capital Cost (106 US$/yr) Overall Cost (106 US$/yr) Savings (106 US$/yr) 5.74 60.4 - 4.05 19.2 6.644 5.789 12.432 2.088 MVGO (pinch Mid PA) 0.16 54.1 -9.63 13.2 4.565 8.555 13.120 1.400 MVGO 285 (pinch HVGO) 5.42 59.4 - 4.37 13.3 5.784 5.728 11.512 3.008

If we keep pinch at HVGO, heat recovery is the same than Case 16,14,6, however the HEN approach is much higher, allowing more heat recovery.

Case Study 3
Pinch Stream Pumparound T Evaluate modifying pinch stream return temperature (if PA)
HVGO: for low 'T high flow rate (pumping need to be evaluated) How will thermodynamics respond to flow variation?

Results Case Study 3


Pinch Stream Pumparound T
MVGO 200 T HVGO pan (C) T HVGO PA return (C) Hot Utility (106 kcal/h) Cold Utility (106 kcal/h) 326 200 3.78 57.8 MVGO 230 324 230 4.07 58.1 MVGO 260 MVGO 285 321 260 4.50 58.5 314 285 5.42 59.4

Heat moving across pinch

arctan(D) arctan(D)

Hot Utility end Tcold Tpinch 55


o

350C
D

Hot utility

326C 314C
D

Grand Compositve Curve

Results Case Study 3

MVGO 260

MVGO 285

Results Case Study 3

MVGO 200 T optimum (C) Utility Cost (106 US$/yr) Capital Cost (106 US$/yr) Overall Cost (106 US$/yr) Savings (106 US$/yr) 19.0 6.181 6.028

MVGO 230 17.2 5.994 5.977

MVGO 260 14.1 5.685 5.954

MVGO 285 13.3 5.784 5.728

12.209

11.971

11.639

11.512

2.311

2.549

2.881

3.008

As HVGO flow rate increases, the HEN approach becomes higher, resulting less Capital Cost, allowing more heat integration.

Discussion Procedure constraints


Pinch analysis assumes direct heat exchange Cost of new sections inside the tower need to be evaluated appart Modification on vacuum and atmospheric collumn simultaneously are not easily evaluated Non optimal design (but close to optimum)

Conclusion

In Case Study 1, moving duty from below to above the pinch (transfering duty from MPA to BPA) reduced Utility Cost with almost no penalty in Capital Cost. In Case Study 2, moving the pinch stream by creating a new drawoff at vacuum tower did not bring benefit initially, as the increase on Capital Cost was too high. However, appropriate flow rate definition for this new stream lead to much higher approaches (lower Capital Cost). In Case Study 3, capital cost becomes higher for lower return PA temperature (lower flow rate).

Conclusion

Appropriate variation of process streams observing thermodynamics may result in high process integration (grass root or revamp) Optimization taking into account these insights could improve the design.

Thank you very much!

Antonio V. S. de Castro, [email protected] Claudio L. M. Kuboski Carlos Ney da Fonseca Silvia Waintraub Washington de O. Geraldelli

You might also like