Scribd
Upload
114 views

Pavement Cracking: A Failure Indicator of Your Roads: Clrp@cornell - Edu WWW - Clrp.cornell - Edu

The document discusses alligator cracking, a common type of pavement failure caused by fatigue from repeated traffic loading. Alligator cracking appears as a series of interconnected cracks forming irregular pieces, similar to an alligator's skin. It typically begins below the surface and progresses upward over time. The severity of alligator cracking can be low, medium, or high depending on the degree of cracking and surface deterioration. Proper repair requires addressing the underlying drainage or base issues causing the flexing, rather than just an overlay, to avoid the cracks returning quickly.

Uploaded by

Satheesh Bose
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
114 views

Pavement Cracking: A Failure Indicator of Your Roads: Clrp@cornell - Edu WWW - Clrp.cornell - Edu

The document discusses alligator cracking, a common type of pavement failure caused by fatigue from repeated traffic loading. Alligator cracking appears as a series of interconnected cracks forming irregular pieces, similar to an alligator's skin. It typically begins below the surface and progresses upward over time. The severity of alligator cracking can be low, medium, or high depending on the degree of cracking and surface deterioration. Proper repair requires addressing the underlying drainage or base issues causing the flexing, rather than just an overlay, to avoid the cracks returning quickly.

Uploaded by

Satheesh Bose
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

March 2012

Pavement Cracking: A Failure Indicator of Your Roads


There are many causes to why pavements fail; one of the most common is fatigue due to pavement deflection. In the CLRP Pavement Maintenance workbook, fatigue is described as the failure of a material due to repetition of many loads. In the workshop, the bending of a paper clip is used to show how the greater the movement or bending angle in the paper clip, the sooner the failure. The same is true in pavements; the greater the load on the surface, the greater the flexing of the pavement surface. This is why roads with heavier loads require different designs than lower/lighter volume roads. Excessive flex in some paved roads can also be found to occur in the spring, when the road base material becomes saturated and soft. Because of this it is a good practice to limit heavy loads on weaker roads during the spring thaw. It is easy to say that a road is under-designed. The bigger issue is how do we fix the problem after it is identified? This is where a better understanding of the types of fatigue that show up in a road is important. Fatigue is typically seen as some form of cracking. Cracking found in pavements vary according to the root cause of the problem. Common types of cracking are fatigue or alligator cracking, longitudinal cracking, transverse cracking, block cracking, slippage cracking, reflective cracking and edge cracking. One of the most important things to consider in roadway maintenance is drainage. The entrance of water into the base material is a major culprit in the acceleration of pavement failure. Water can enter into the base material in several ways. The most obvious is through the existing cracks in the road surface. Other means of water access to the base are through the piping of ground water up through the base, high exposed pavement edges, and standing water on a road without a crown. The CLRP Pavement Maintenance workbook identifies typical types of cracking, their causes and repair options. One of the more common types of cracking is alligator cracking, also referred to as fatigue cracking. Below we will briefly discuss alligator cracking to better understand and identify the severity of this type of cracking.
CORNELL LOCAL ROADS PROGRAM 416 RILEY-ROBB HALL, ITHACA, NY 14853 PHONE: (607) 255-8033 FAX: (607) 255-4080 E-MAIL: [email protected] INTERNET: www.clrp.cornell.edu

Tech Tips are published by the Cornell Local Roads Program with support from the Federal Highway Administration, the New York State Department of Transportation, and Cornell University. The content is the responsibility of the Local Roads Program.

PAVEMENT CRACKING: A FAILURE INDICATOR OF YOUR ROADS

FaTigUe (AlligaTor) CracKing

Alligator cracking is characterized as a series of interconnected cracks creating small, irregular shaped pieces of pavement. The sizes of these irregular shaped pieces vary, from less than 12-inches to 24-inches. The cracking pattern is similar to the pattern found on alligator skin, and therefore the source of its name. The cause of this type of cracking is the failure of the bound layer due to repeated traffic loading resulting in the disintegration of the surface and eventually potholes. The cracking starts out of sight, at the bottom of the surface course or in the stabilized base where the tension stresses are the highest. As the pavement flexes under repeated wheel loading the crack moves upward toward the surface eventually leading to failure. As the wheel loading continues, more cracks are formed. Repair - The type of repair is dependent on the extent and severity of the failure area. There are three levels of severity used in rating alligator cracking: Low Severity Cracking Low Severity is characterized by an area of cracking with very narrow cracks with almost no deterioration of the surface. The cracking is often isolated and many times the cracking may not be interconnected to other areas and there is not much distortion. These cracks may be sealed to extend the useful life of the pavement, but the underlying cause may still lead to additional premature cracking. Medium Severity Cracking Medium Severity is characterized by interconnected cracking forming a small area of the typical alligator pattern. The cracks may have signs of slight spalling, with no pumping visible. Sealing of the surface cracks may be an option but should be carefully considered to avoid creating slick spots on the pavement surface. In smaller areas a proper fix would be to remove and replace the base and surface (i.e. a box out and replacement). Providing subsurface drainage may help in preventing the need for future repairs. Larger areas will require either reclamation or reconstruction.

Example of low severity cracking

Example of medium severity cracking

TECH TIPS

March 2012

Page 2 of 6

PAVEMENT CRACKING: A FAILURE INDICATOR OF YOUR ROADS

High Severity Cracking High Severity alligator cracking is characterized by an area of moderate to severe spalled interconnected cracks creating a full pattern of cracking. Pieces of asphalt may be loose or missing from traffic and the pumping of water or fine material from below the pavement may be present on the surface. As with medium severity, in smaller areas a proper fix would be to remove and replace the base and surface. Providing subsurface drainage may help in preventing the need for future repairs. Larger areas will require either reclamation of reconstruction.

Examples of high severity cracking

In all cases, it is advisable to look into the drainage in these areas since this type of failure can be caused by poor drainage within the base layer. Caution should also be taken when using a crack seal on this type of failure. Excessive crack seal material create slick and potentially dangerous safety issues due to the reduced friction surface in both wet and hot weather. Identifying the severity and extent of cracking on a road can assist in determining the cause of the failure and the appropriate repair that will provide the best long term solution to eliminating or reducing the problem. There is no one treatment fix-all when repairing roads. Without properly repairing the drainage and/or the base problem causing the alligator cracking will only prolong the return of the cracking. An asphalt overlay will only temporarily fix an alligator cracked road. Due to the continual flex movement of the base, an overlay will eventually fail due to the same underlying problems. The typical failure rate, in this case, for an overlay is approximately 1-inch of asphalt per year. So for a 2-inch overlay, one could expect the cracking to return in 2-years. In higher traffic, the failure may return sooner. Because of this and the associated costs of road repairs, recognizing the type of asphalt surface failure and the understanding the cause of the failure is an important step in properly utilizing the everlimited funds available to make these repairs.

TECH TIPS

March 2012

Page 3 of 6

PAVEMENT CRACKING: A FAILURE INDICATOR OF YOUR ROADS

OTher Types of PaVemenT FailUre

Bleeding

Block Cracking

Edge Cracking

Longitudinal Cracks

Overlay Delamination
TECH TIPS March 2012

Polishing of Asphalt
Page 4 of 6

PAVEMENT CRACKING: A FAILURE INDICATOR OF YOUR ROADS

Rutting

Shoving of Asphalt

Transverse Crack
TECH TIPS March 2012 Page 5 of 6

PAVEMENT CRACKING: A FAILURE INDICATOR OF YOUR ROADS

ResoUrces:

Distress Identification Manual, U.S. Department of Transportation, FHWA-RD-03-031, June 2003. Road Surface Management System, Technology Transfer Center University of New Hampshire, May 2003. Pavement Maintenance, David Orr, PE, Cornell Local Roads Program, March 2006 www.clrp.cornell.edu/workshops/manuals/pavement_maintenance.pdf.

This article was first printed in the Winter 2012 Nuggets & Nibbles newsletter.

This work by the Cornell Local Roads Program (CLRP) is licensed under a

TECH TIPS

March 2012

Page 6 of 6

You might also like