Scribd
Upload
195 views

CMM CAD Programming 1

The document provides instructions for calibrating and using the TESA MICRO-HITE 3D machine. It outlines steps such as turning on the machine, calibrating axes, defining measurement planes and origins, and registering points to measure objects. Key steps include recognizing the origin point, defining datums on reference surfaces, establishing X and Y axes by selecting points, and measuring by contacting the probe to surfaces at points.

Uploaded by

Supriya Sahu
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
195 views

CMM CAD Programming 1

The document provides instructions for calibrating and using the TESA MICRO-HITE 3D machine. It outlines steps such as turning on the machine, calibrating axes, defining measurement planes and origins, and registering points to measure objects. Key steps include recognizing the origin point, defining datums on reference surfaces, establishing X and Y axes by selecting points, and measuring by contacting the probe to surfaces at points.

Uploaded by

Supriya Sahu
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

TESA MICRO-HITE 3D

Quick reference guide -Last updated 01/30/09 Uncover machine, make sure air supply is hooked up, Turn on machine at left side of touch screen

Press button next to check mark to accept Language default setting Press this button every time the reading taken by the machine is to be accepted

Follow instructions for calibration every time machine is to be used after being off.

First task is to recognize the origin point . Follow instructions on screen

Every axis can be locked in position at any time with switches at vertical sliding arm

IMPORTANT: Push and pull vertical sliding arm every time you move on the Y axis

Accept the default for TTP Probe

Next task is to remove the probe and place Z rail against the sphere

Before you do this, move Z rail close to the current position of the ball

Remove the probe loosening the lever at the right side of Z rail Position bottom of Z rail on top of the sphere and accept the point Reattach Probe to Z rail at the same position it was before (light in front)

Next task is to measure the qualification sphere IMPORTANT: For all following tasks and to measure anything points have to be registered contacting probe to surfaces. To do this, carefully move probe close and make contact with the surface approaching it very slowly and normal to the surface. Do not drag probe across surface.

You need to contact the sphere on five points. First touch the top of the sphere. Next, you need to touch four sides along the equator of the sphere, a suggested way to do this is to get the probe in position then lock the Z axis

Contact four points around the sphere Unlock Z axis

Accept reading of Probe tip summary (unless the reading is not within tolerance)

Press button next to Measurement icon

The measurement screen is blank and shows the position of the probe from the origin point established in the beginning, at the front, top left side of the machine

Register four or more points in the granite surface to define a plane for the origin of the Z axis

Accept the reading when the arrow is in the plane icon position

Another way to accept a reading is to push the check mark button in the Z rail

Sometimes a circle is registered when you are trying to define a plane, this is because the software recognizes three or more points as defining a circle as if they were intersecting the circle.

Cancel the circle definition by pressing the button next to icon shown. This icon cancels the last reading registered.

The best approach to avoid registering a circle is to select four points on surface, one of them inscribed inside three points defining a triangular shape

The screen at the left shows how a plane is registered

Press button to define this plane as datum A This establishes the origin of the Z axis in this plane

Once you define this plane as a datum, you should see the screen turn to this

Next you need to define the X and Y axis directly on the part you are measuring To do this pick two points first to define the X axis line. First point to be picked must be on the left relative to the other one.

Pick second point

A line is registered in the screen. Accept this

Sometimes you get a screen asking you to establish this selection of points as a plane. Exit the screen and register two points again

Register two points at the left of the part to define the Y axis line

This is what a defined line looks like in the screen

Select the tools icon to establish a relationship between the two lines you picked.

Pick relationships from tools screen (not shown) Pick the two lines you created by selecting the x mark once you highlight every line

Accept the selections and select the button shown at the left, this will establish the intersection of the two lines as origin C, which will make the lines to act as X and Y axes

Once established, this is what the new origin looks like

It represents the zero position for the X and Y axes, and combined with the A datum, gives you the 0,0,0 position shown in picture

Now you can start measuring. Select any point in your part and accept it

It usually registers as shown in the screen at left Bottom value X shown is the distance from the origin in the X axis.

You might also like