Scribd
Upload
139 views

Lightning Protection of Distribution Lines

This document discusses lightning protection of distribution lines. It describes different types of lightning strikes such as direct strikes, induced flashes, and back flashes. Direct strikes are the most difficult to protect against as they can cause voltages up to 4 MV on the line. Shield wires and arresters are common protection methods. Shield wires aim to prevent direct strikes while arresters limit surge voltages from both direct and induced flashes. Proper shield wire installation and grounding is important for effective protection.

Uploaded by

kolombo1776
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
139 views

Lightning Protection of Distribution Lines

This document discusses lightning protection of distribution lines. It describes different types of lightning strikes such as direct strikes, induced flashes, and back flashes. Direct strikes are the most difficult to protect against as they can cause voltages up to 4 MV on the line. Shield wires and arresters are common protection methods. Shield wires aim to prevent direct strikes while arresters limit surge voltages from both direct and induced flashes. Proper shield wire installation and grounding is important for effective protection.

Uploaded by

kolombo1776
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 18

Lightning Protection of Distribution Lines

John McDaniel Chair WG on Lightning Performance of Distribution Lines

Flashover Mechanisms

What are we trying to protect against


Direct Strike to line Induced from nearby strike


Most typical flashover on distribution

Back flash from strike to shield wire

Direct Stroke

Lightning hits phase conductor


Current splits in both directions

Average current of 20 kA will cause a voltage of 4 MV on line


* 20 kA * 400 ohms (typical surge impedance)

Most difficult to protect against

Number of Strikes to a Line


Erikssons equation:
28h 0.6 + b N = Ng 10

Where:

Assumes that the line is in open ground

h is pole height b is structure width (negligible for distribution) Ng is GFD

Induced Flashover

Lightning strikes near line and induces a voltage on it


Vmax = 38.8*(IO*ha)/y

Where: IO is peak lightning current

ha is average height of line y is the distance from line of lightning stroke

Most typical of lightning fashovers on a distribution line Much less energy than a direct strike

Lightning Strike in Open Ground No Natural Shielding


rs = 10*IO0.65 the striking distance rg=0.9*rs

Back Flashover

Lightning hits shield wire Surge divert to ground thru ground wire off of shield Voltage is dependant on ground resistance and lightning current

Protection of Lines

Shielding

Shield Wire Natural

Arresters Added insulation

Shielding

Shield wire used to prevent direct strike to line


Need good ground resistance Dependant on shield angle Trees, buildings, fences.

Nearby objects can act as a shield


Shield Angle

Figure 7 from IEEE Std. 1410-2004

Effect of ground resistance on shield-wire performance

Figure 8 from IEEE Std. 1410-2004

CFO

CFO is Critical Flashover


The voltage level where 50% chance of flashover

Combination of the components on pole Tables 2 4 in IEEE Std. 1410 contain the values for the CFOs If value not in tables 3 or 4, use equation 11 In IEEE Std. 1410

CFOT = CFOins + CFOadd .sec + CFOadd .third + ... + CFOadd .nth

CFOadd.sec = 0.45*CFO CFOadd.third = 0.20*CFO

CFO Explained

CFO1: Insulator

105 kV (Value from Table 2 IEEE 1410) 250 kV/m (Table 3)

CFO2:X-Arm

CFO3:Brace or Insulator

Brace: 0.2*360 kV/m Insulator: 0.2*105 kV From equation 11 IEEE 1410

EMG & Striking Distance


Natural Shielding

10 m

X
Courtesy of Progress Energy-Florida

Figure 4 from IEEE Std. 1410-2004

Arresters

Protection for both direct strokes and induced flashovers Limit voltage by shunting the lightning surge to ground Performance based on spacing of arresters and to some extent ground resistance

IEEE Std. 1410-2004


Can be purchased from IEEE SA at: http://shop.ieee.org/ieeestore/Product. aspx?product_no=SH95218

You might also like