Commercial Series

CP140/CP160/CP180 Portable Radios

Basic Service Manual
6866550D17-O

Issue: December 2003

ii

Computer Software Copyrights

The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form, the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied or reproduced in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant, either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive royalty-free license to use that arises by operation of law in the sale of a product.

iii

SAFETY INFORMATION
Read this information before using the radio.

PRODUCT SAFETY AND RF EXPOSURE FOR PORTABLE TWO-WAY RADIOS.

This document provides information and instructions for the safe and efficient operation of Motorola Portable Two-Way Radios. The information provided in this document supersedes information contained in user guides published prior to February 2002.

COMPLIANCE WITH RF ENERGY EXPOSURE STANDARDS

Note:This Radio is intended for use in occupational/controlled applications, where users have been made aware of the potential for exposure and can exercise control over their exposure. This radio device is NOT authorized for general population, consumer or similar use. This document includes useful information about RF exposure and helpful instructions on how to control RF exposures. Motorola radios are designed and tested to comply with a number of national and international standards and guidelines regarding human exposure to radio frequency electromagnetic energy. This radio complies with IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environments at usage factors of up to 50% talk50% listen. In terms of measuring RF energy for compliance with the IEEE/ICNIRP exposure guidelines, the radio radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE: The approved batteries, supplied with this radio, are rated for a 5-5-90 duty cycle (5% talk5% listen90% standby), even though this radio complies with IEEE/ICNIRP occupational exposure limits at usage factors of up to 50% talk.

PORTABLE RADIO OPERATION AND EME EXPOSURE

Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:
G G G

Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 United States Federal Communications Commission, Code of Federal Regulations; 47 CFR part 2 sub-part J American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard 2001 ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) additional requirements for SMR, cellular and PCS product certification.

iv

COMPLIANCE AND CONTROL GUIDELINES AND OPERATING INSTRUCTIONS FOR PORTABLE TWO-WAY RADIOS
To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures:
G

Transmit no more than 50% of the time. To transmit (talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time or less is important since the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least 2.5 to 5 centimeters ( one to two inches) away from the lips. Keeping the radio at a proper distance is important since RF exposures decrease with distance from the antenna. For body-worn operation, always place the radio in a Motorola approved clip, holder, holster, case, or body harness for this product. Using Motorola non-approved accessories may result in exposure levels which exceed the IEEE/ICNIRP occupational /controlled environment RF exposure limits. If you are not using a body-worn accessory and are not using the radio in the intended use position in front of the face, then ensure the antenna and the radio are kept 2.5 cm (one inch) from the body when transmitting. Keeping the radio at a proper distance is important because of RF exposures decrease with distance from the antenna.

Use only Motorola-approved supplied or replacement antennas, batteries, and accessories. Use of non-Motorola approved antennas, batteries and accessories may exceed IEEE/ICNIRP RF exposure guidelines. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories: http://moleurope.comm.mot.com/member/commerce For additional information on exposure requirements or other training information, visit http://www.motorola.com/rfhealth.

ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY
NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility.

Facilities
To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy.

Aircraft
When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions.

Medical Devices
Pacemakers

The Advanced Medical Technology Association (AdvaMed) recommends that a minimum separation of 15 cms (6 inches) be maintained between a handheld wireless radio and a pacemaker.These recommendations are consistent with those of the U.S. Food and Drug Administration. Persons with pacemakers should:
G G G G

ALWAYS keep the radio more than 15 cms from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference. Turn the radio OFF immediately if you have any reason to suspect that interference is taking place.

Hearing Aids

Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives.
Other Medical Devices

If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information.

Driver Safety
Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please:
G G G

Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call if driving conditions so require.

vi

OPERATIONAL WARNINGS Vehicles with an air bag

WARNING: Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle.

Potentially explosive atmospheres

!
NOTE

WARNING: Turn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a radio type especially qualified for use in such areas as "Intrinsically Safe" (for example, Factory Mutual, CSA, UL or CENELEC Approved). Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. The areas with potentially explosive atmospheres referred to above include fuelling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often but not always posted.

Blasting caps and areas

WARNING: To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: "Turn off two-way radio". Obey all signs and instructions.

OPERATIONAL CAUTIONS Damaged antennas

! !

CAUTION: Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.

Batteries
CAUTION: All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewellery, keys, or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects.

Table of Contents

vii

Table of Contents
Safety Information.........................................................................................iii Chapter 1
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8

Model Charts and Test Specifications .............................. 1-1

Radio Model Information................................................................................................................ 1-1 Model Chart for VHF 146-174 MHz ............................................................................................... 1-2 VHF Specifications ........................................................................................................................ 1-3 Model Chart for UHF 403-440 MHz ............................................................................................... 1-4 Model Chart for UHF 438-470 MHz ............................................................................................... 1-5 Model Chart for UHF 465-495 MHz ............................................................................................... 1-6 UHF Specifications ........................................................................................................................ 1-7 MIL Standards ............................................................................................................................... 1-8

Chapter 2
2.1 2.2

Theory Of Operation ........................................................... 2-1

Introduction .................................................................................................................................... 2-1 Major Assemblies .......................................................................................................................... 2-1 2.2.1 Receiver............................................................................................................................ 2-1 2.2.2 Transmitter........................................................................................................................ 2-2

Chapter 3
3.1 3.2

Test Equipment, Service Aids, and Service Tools....................................................................... 3-1

Test Equipment.............................................................................................................................. 3-1 Service Aids................................................................................................................................... 3-2

Chapter 4
4.1 4.2 4.3

Performance Checks .......................................................... 4-1

General .......................................................................................................................................... 4-1 Power-Up Self Test........................................................................................................................ 4-1 RF Test Mode ................................................................................................................................ 4-2

Chapter 5
5.1 5.2 5.3 5.4

Radio Alignment Procedures............................................. 5-1

Introduction .................................................................................................................................... 5-1 CPS Programming Setup .............................................................................................................. 5-1 Radio Tuning Setup ....................................................................................................................... 5-2 5.3.1 Initial Test Equipment Control Settings............................................................................. 5-3 Radio-to-Radio Cloning ................................................................................................................. 5-3

viii

Table of Contents

Chapter 6
6.1 6.2 6.3 6.4

Full Keypad Model Disassembly and Re-assembly ........................................................................ 6-1

6.5

Introduction .................................................................................................................................... 6-1 Preventive Maintenance ................................................................................................................ 6-1 6.2.1 Inspection.......................................................................................................................... 6-1 6.2.2 Cleaning Procedures ........................................................................................................ 6-1 Safe Handling of CMOS and LDMOS Devices .............................................................................. 6-2 Disassembling and Re-assembling the Radio General............................................................. 6-3 6.4.1 Radio Disassembly Detailed ........................................................................................ 6-3 6.4.1.1 Front Cover From Chassis Disassembly ........................................................... 6-3 6.4.1.2 Dust Cover Disassembly.................................................................................... 6-6 6.4.1.3 Speaker and Microphone Disassembly ............................................................. 6-6 6.4.1.4 Keyboard Removal ............................................................................................ 6-7 6.4.1.5 PTT Disassembly............................................................................................... 6-7 6.4.1.6 Chassis Disassembly......................................................................................... 6-8 6.4.2 Radio Re-assembly - Detailed .......................................................................................... 6-9 6.4.2.1 Dust Cover Re-assembly ................................................................................... 6-9 6.4.2.2 Microphone and Speaker Re-assembly............................................................. 6-9 6.4.2.3 Keypad and LCD/Keyboard Re-assembly ....................................................... 6-11 6.4.2.4 Keyboard Retainer Re-assembly ..................................................................... 6-12 6.4.2.5 Chassis Assembly/Re-assembly...................................................................... 6-12 6.4.2.6 Chassis and Front Cover Re-assembly ........................................................... 6-13 6.4.2.7 PTT Re-assembly ............................................................................................ 6-15 Mechanical View and Parts List ................................................................................................... 6-16 6.5.1 CP180 Full-Keypad Exploded View and Parts List ......................................................... 6-16

Chapter 7
7.1 7.2 7.3 7.4

Limited Keypad Model Disassembly and Re-assembly ........................................................................ 7-1

7.5

Introduction .................................................................................................................................... 7-1 Preventive Maintenance ................................................................................................................ 7-1 7.2.1 Inspection.......................................................................................................................... 7-1 7.2.2 Cleaning Procedures ........................................................................................................ 7-1 Safe Handling of CMOS and LDMOS Devices .............................................................................. 7-2 Disassembling and Re-assembling the Radio General............................................................. 7-3 7.4.1 Radio Disassembly Detailed ........................................................................................ 7-3 7.4.1.1 Front Cover from Chassis Disassembly............................................................. 7-3 7.4.1.2 Dust Cover Disassembly.................................................................................... 7-6 7.4.1.3 Speaker and Microphone Disassembly ............................................................. 7-6 7.4.1.4 Keyboard Removal ............................................................................................ 7-7 7.4.1.5 PTT Disassembly............................................................................................... 7-8 7.4.2 Chassis Disassembly ........................................................................................................ 7-8 7.4.3 Radio Re-assembly - Detailed .......................................................................................... 7-9 7.4.3.1 Dust Cover Re-assembly ................................................................................... 7-9 7.4.3.2 Microphone and Speaker Re-assembly............................................................. 7-9 7.4.3.3 Keypad and LCD/Keyboard Re-assembly ....................................................... 7-11 7.4.3.4 Keyboard Retainer Re-assembly ..................................................................... 7-12 7.4.3.5 Chassis Assembly/Re-assembly...................................................................... 7-12 7.4.3.6 Chassis and Front Cover Re-assembly ........................................................... 7-13 7.4.3.7 PTT Re-assembly ............................................................................................ 7-15 Mechanical View and Parts List ................................................................................................... 7-16 7.5.1 CP160 Limited-Keypad Exploded View and Parts List ................................................... 7-16

Table of Contents

ix

Chapter 8
8.1 8.2 8.3 8.4

Non-Keypad Model Disassembly and Re-assembly ........................................................................ 8-1

8.5

Introduction .................................................................................................................................... 8-1 Preventive Maintenance ................................................................................................................ 8-1 8.2.1 Inspection ......................................................................................................................... 8-1 8.2.2 Cleaning Procedures ........................................................................................................ 8-1 Safe Handling of CMOS and LDMOS Devices.............................................................................. 8-2 Disassembling and Re-assembling the Radio General............................................................. 8-3 8.4.1 Radio Disassembly Detailed ........................................................................................ 8-3 8.4.1.1 Front Cover From Chassis Disassembly ........................................................... 8-3 8.4.1.2 Dust Cover Disassembly ................................................................................... 8-5 8.4.1.3 Speaker and Microphone Disassembly ............................................................. 8-6 8.4.1.4 PTT Disassembly............................................................................................... 8-6 8.4.2 Chassis Disassembly........................................................................................................ 8-7 8.4.3 Radio Re-assembly - Detailed .......................................................................................... 8-8 8.4.3.1 Dust Cover Re-assembly................................................................................... 8-8 8.4.3.2 Microphone and Speaker Re-assembly............................................................. 8-8 8.4.3.3 Chassis Assembly/Re-assembly ....................................................................... 8-9 8.4.3.4 Chassis and Front Cover Re-assembly ........................................................... 8-10 8.4.3.5 PTT Re-assembly ............................................................................................ 8-12 Mechanical View and Parts List................................................................................................... 8-13 8.5.1 CP140 Non-Keypad Exploded View and Parts List ........................................................ 8-13

Chapter 9
9.1 9.2 9.3 9.4

Troubleshooting Tables ..................................................... 9-1

Power-Up Error Codes .................................................................................................................. 9-1 Operational Error Codes................................................................................................................ 9-1 Troubleshooting Table for Receiver............................................................................................... 9-2 Troubleshooting Table for Transmitter........................................................................................... 9-3

Appendix A Accessories .........................................................................A-1 Appendix B Warranty, Service Support, and Replacement Parts .......B-1
1.0 2.0 2.3 2.4 2.5 Scope of Manual............................................................................................................................B-1 Warranty ........................................................................................................................................B-1 2.1 Warranty Period and Return Instructions..........................................................................B-1 2.2 After Warranty Period .......................................................................................................B-1 European Radio Support Centre ...................................................................................................B-2 Piece Parts ....................................................................................................................................B-2 Technical Support..........................................................................................................................B-3

Glossary .......................................................................................................G1

Table of Contents

Chapter 1 Model Charts and Test Specifications

1.1

Radio Model Information

The model number and serial number are located on a label attached to the back of your radio. You can determine the RF output power, frequency band, protocols, and physical packages. The example below shows one portable radio model number and its specific characteristics. Table 1-1. Radio Model Number (Example: MDH65KDC9AA2AN) Type of Model Unit Series Freq. Band K VHF (146174 MHz) Q UHF1 (403440 MHz) R UHF2 (438470 MHz) S UHF3 (465495 MHz) Power Physical Channel Level Packages Spacing 9 D C Program4 W or Non mable 5W Display F Limited Keypad H Full Keypad Protocol AA Conventional Feature Model Model Level Revision Package 2 16 Chan 3 32 Chan 4 64 Chan A N

MD

65

MD = Motorola Internal Use

H = Portable

1-2

Model Charts and Test Specifications: Model Chart for VHF 146-174 MHz

1.2

Model Chart for VHF 146-174 MHz CP100 Series, VHF, 146-174 MHz
Model Description CP140, 146-174 MHz, 5 W, 16 Ch. Non-Display Model CP160, 146-174 MHz, 5 W, 32 Ch. Limited Keypad Model CP180, 146-174 MHz, 5 W, 64 Ch. Full Keypad Model Description CP140, 146-174 MHz, Tanapa CP160, 146-174 MHz, Tanapa CP180, 146-174 MHz, Tanapa CP140, Back Cover Kit. 146-174 MHz CP160, Back Cover Kit. 146-174 MHz CP180, Back Cover Kit. 146-174 MHz CP140, Front Housing Kit, 16 Ch. CP160, Front Housing Kit, 32 Ch. CP180, Front Housing Kit, 64 Ch. Li-Ion Battery, High Capacity 1800 mAH NiMh Battery, 1400 mAH NiMh Battery, 1300 mAH FM Slim Li-Ion Battery 1600 mAH NiCd Battery, 1100 mAH Rapid Desktop Charger w/US Plug Rapid Desktop Charger w/Euro Plug Rapid Desktop Charger w/UK Plug 3 Belt Clip Antenna, 146-174 MHz, 14cm CP140/CP160/CP180 User Guide FM Product Listing Manual Safety and General Information Leaflet

MDH65KDC9AA2AN MDH65KDF9AA3AN MDH65KDH9AA4AN Item X X X X X X PMUD1857_ PMUD1858_ X PMUD1859_ PMLD4222_ PMLD4223_ X PMLD4224_ PMLN4601_ PMLN4602_ X PMLN4603_ X X X NNTN4497_R X X X NNTN4851_ X X X NNTN4852_ X X X NNTN4970 X X X NNTN4496_R X X X WPLN4138_R X X X WPLN4139_R X X X WPLN4140_R X X X HLN8255 X X X NAD6502_R X X 6866550D01 6881096C29 X 6864117B25_

X = Indicates compatibility with model(s)

VHF Specifications

1-3

1.3

VHF Specifications
General
VHF

Transmitter
VHF RF Output NiMH @ 7.5 V: Frequency: Channel Spacing: Freq. Stability: (-30C to +60C) Spurs/Harmonics: Audio Response: (from 6 dB/oct. Pre-emphasis, 300 to 3000 Hz) Audio Distortion: @ 1000 Hz, 60% Rated Max. Dev. FM Noise: Low 1W 146-174 MHz 12.5/20/25 kHz 0.00025% -36 dBm < 1 GHz -30 dBm > 1 GHz +1, -3 dB High 5W 146-174 MHz 16, 32, or 64 Channels 7.5 Volts 20%
130.5mm H x 62mm W x 45mm D 130.5mm H x 62mm W x 45mm D 130.5mm H x 62mm W x 45mm D 130.5mm H x 62mm W x 43mm D 130.5mm H x 62mm W x 42mm D

Frequency: Channel Capacity: Power Supply: Dimensions with: High Capacity Li-Ion, NiMH FM NiCd Std NiMH Std Slim Li-Ion Batteries: Weight: for 16 Channel Model Batteries: High Capacity Li-Ion NiMH FM NiCd Std NiMH Std Slim Li-Ion Weight: for 32 & 64 Channel Model Batteries: High Capacity Li-Ion NiMH FM NiCd Std NiMH Std Slim Li-Ion

376g (13.26 oz.) 449g (15.83 oz.) 430g (15.17 oz.) 446g (15.73 oz.) 337g (13.30 oz.)

<3%

-40 dB (12.5 kHz) -45 dB (25 kHz)

396g (13.97 oz.) 469g (16.54 oz.) 451g (15.91 oz.) 467g (16.47 oz.) 377g (14.0 oz.) 1W 19 Hrs. 11 Hrs. 10 Hrs. 13 Hrs. 17 Hrs.

Receiver
VHF 12.5 kHz Frequency: Sensitivity 12 dB EIA SINAD: Adjacent Channel Selectivity: Intermodulation: Freq. Stability (-30C to +60C): Spur Rejection: Image and 1/2 I-F Rejection: Audio Output @ <5% Distortion: 146-174 MHz 0.25 V (typical) -65 dB - 70 dB 0.00025% -75 dB -70 dB 500 mW -70 dB VHF 20/25kHz

Average Battery Life Capacity 5W @ (5-5-90 Duty (mAh) Cycle): High Capacity Li-Ion 1800 14 Hrs. NiMH FM 1300 9 Hrs. NiCd Std 1100 8 Hrs. NiMH Std 1400 10 Hrs. Slim Li-Ion 1600 12 Hrs.

Self-Quieter Frequencies VHF

151.19375 151.200 151.20625 167.99375 168.000 168.00625

All specifications are subject to change without notice.

1-4

Model Charts and Test Specifications: Model Chart for UHF1 403-440 MHz

1.4

Model Chart for UHF1 403-440 MHz CP100 Series, UHF1, 403-440 MHz
Model Description CP140, 403-440 MHz, 4 W, 16 Ch. Non-Display Model CP160, 403-440 MHz, 4 W, 32 Ch. Limited Keypad Model CP180, 403-440 MHz, 4 W, 64 Ch. Full Keypad Model Description CP140, 403-440 MHz, Tanapa CP160, 403-440 MHz, Tanapa CP180, 403-440 MHz, Tanapa CP140, Back Cover Kit. 403-440 MHz CP160, Back Cover Kit. 403-440 MHz CP180, Back Cover Kit. 403-440 MHz CP140, Front Housing Kit, 16 Ch. CP160, Front Housing Kit, 32 Ch. CP180, Front Housing Kit, 64 Ch. Li-Ion Battery, High Capacity 1800 mAH NiMh Battery, 1400 mAH NiMh Battery, 1300 mAH FM Slim Li-Ion Battery 1600 mAH NiCd Battery, 1100 mAH Rapid Desktop Charger w/US Plug Rapid Desktop Charger w/Euro Plug Rapid Desktop Charger w/UK Plug 3 Belt Clip Antenna, 403-520 MHz, 14cm CP140/CP160/CP180 User Guide FM Product Listing Manual Safety and General Information Leaflet

MDH65QDC9AA2AN MDH65QDF9AA3AN MDH65QDH9AA4AN Item X X X X X X PMUE1972_ PMUE1973_ X PMUE1974_ PMLE4282_ PMLE4285_ X PMLE4286_ PMLN4601_ PMLN4602_ X PMLN4603_ X X X NNTN4497_R X X X NNTN4851_ X X X NNTN4852_ X X X NNTN4970 X X X NNTN4496_R X X X WPLN4138_R X X X WPLN4139_R X X X WPLN4140_R X X X HLN8255 X X X NAE6483_ X X 6866550D01 6881096C29 X 6864117B25_

X = Indicates compatibility with model(s)

Model Charts and Test Specifications: Model Chart for UHF2 438-470 MHz

1-5

1.5

Model Chart for UHF2 438-470 MHz CP100 Series, UHF2, 438-470 MHz
Model Description CP140, 438-470 MHz, 4 W, 16 Ch. Non-Display Model CP160, 438-470 MHz, 4 W, 32 Ch. Limited Keypad Model CP180, 438-470 MHz, 4 W, 64 Ch. Full Keypad Model Description CP140, 438-470 MHz, Tanapa CP160, 438-470 MHz, Tanapa CP180, 438-470 MHz, Tanapa CP140, Back Cover Kit. 438-470 MHz CP160, Back Cover Kit. 438-470 MHz CP180, Back Cover Kit. 438-470 MHz CP140, Front Housing Kit, 16 Ch. CP160, Front Housing Kit, 32 Ch. CP180, Front Housing Kit, 64 Ch. Li-Ion Battery, High Capacity 1800 mAH NiMh Battery, 1400 mAH NiMh Battery, 1300 mAH FM Slim Li-Ion Battery 1600 mAH NiCd Battery, 1100 mAH Rapid Desktop Charger w/US Plug Rapid Desktop Charger w/Euro Plug Rapid Desktop Charger w/UK Plug 3 Belt Clip Antenna, 403-520 MHz, 14cm CP140/CP160/CP180 User Guide FM Product Listing Manual Safety and General Information Leaflet

MDH65RDC9AA2AN MDH65RDF9AA3AN MDH65RDH9AA4AN Item X X X X X X PMUE1966_ PMUE1967_ X PMUE1968_ PMLE4283_ PMLE4290_ X PMLE4291_ PMLN4601_ PMLN4602_ X PMLN4603_ X X X NNTN4497_R X X X NNTN4851_ X X X NNTN4852_ X X X NNTN4970 X X X NNTN4496_R X X X WPLN4138_R X X X WPLN4139_R X X X WPLN4140_R X X X HLN8255 X X X NAE6483_ X X 6866550D01 6881096C29 X 6864117B25_

X = Indicates compatibility with model(s)

1-6

Model Charts and Test Specifications: Model Chart for UHF3 465-495 MHz

1.6

Model Chart for UHF3 465-495 MHz CP100 Series, UHF3, 465-495 MHz
Model Description CP140, 465-495 MHz, 4 W, 16 Ch. Non-Display Model CP160, 465-495 MHz, 4 W, 32 Ch. Limited Keypad Model CP180, 465-495 MHz, 4W, 64 Ch. Full Keypad Model Description CP140, 465-495 MHz, Tanapa CP160, 465-495 MHz, Tanapa CP180, 465-495 MHz, Tanapa CP140, Back Cover Kit. 465-495 MHz CP160, Back Cover Kit. 465-495 MHz CP180, Back Cover Kit. 465-495 MHz CP140, Front Housing Kit, 16 Ch. CP160, Front Housing Kit, 32 Ch. CP180, Front Housing Kit, 64 Ch. Li-Ion Battery, High Capacity 1800 mAH NiMh Battery, 1400 mAH NiMh Battery, 1300 mAH FM Slim Li-Ion Battery 1600 mAH NiCd Battery, 1100 mAH Rapid Desktop Charger w/US Plug Rapid Desktop Charger w/Euro Plug Rapid Desktop Charger w/UK Plug 3 Belt Clip Antenna, 403-520 MHz, 14cm CP140/CP160/CP180 User Guide FM Product Listing Manual Safety and General Information Leaflet

MDH65SDC9AA2AN MDH65SDF9AA3AN MDH65SDH9AA4AN Item X X X X X X PMUE1978_ PMUE1979_ X PMUE1980_ PMLE4294_ PMLE4295_ X PMLE4296_ PMLN4601_ PMLN4602_ X PMLN4603_ X X X NNTN4497_R X X X NNTN4851_ X X X NNTN4852_ X X X NNTN4970 X X X NNTN4496_R X X X WPLN4138_R X X X WPLN4139_R X X X WPLN4140_R X X X HLN8255 X X X NAE6483_ X X 6866550D01 6881096C29 X 6864117B25_

X = Indicates compatibility with model(s)

UHF Specifications

1-7

1.7

UHF Specifications
General
UHF

Transmitter
UHF RF Output NiMH @ 7.5 V: Frequency: Low 1W 403-440 MHz 438-470 MHz 465-495 MHz 12.5/20/25 kHz 0.00025% -36 dBm < 1 GHz -30 dBm > 1 GHz +1, -3 dB High 4W 403-440 MHz 438-470 MHz 465-495 MHz 16, 32, or 64 Channels 7.5 Volts 20%
130.5mm H x 62mm W x 45mm D 130.5mm H x 62mm W x 45mm D 130.5mm H x 62mm W x 43mm D 130.5mm H x 62mm W x 42mm D

Frequency:

Channel Capacity: Power Supply: Dimensions with: High Capacity Li-Ion, NiMH FM/NiCd Std NiMH Std Slim Li-Ion Batteries: Weight: for 16 Channel Model Batteries: High Capacity Li-Ion NiMH FM NiCd Std NiMH Std Slim Li-Ion Weight: for 32 & 64 Channel Model Batteries: High Capacity Li-Ion NiMH FM NiCd Std NiMH Std Slim Li-Ion

Channel Spacing: Freq. Stability: (-30C to +60C) Spurs/Harmonics: Audio Response: (from 6 dB/oct. Preemphasis, 300 to 3000 Hz) Audio Distortion: @ 1000 Hz, 60% Rated Max. Dev. FM Noise:

376g (13.26 oz.) 449g (15.83 oz.) 430g (15.17 oz.) 446g (15.73 oz.) 337g (13.30 oz.)

<3%

396g (13.97 oz.) 469g (16.54 oz.) 451g (15.91 oz.) 467g (16.47 oz.) 377g (14.0 oz.) 1W 19 Hrs. 11 Hrs. 10 Hrs. 13 Hrs. 17 Hrs.

-40 dB (12.5 kHz) -45 dB (25 kHz)

Receiver
UHF 12.5 kHz Frequency: 403-440 MHz 438-470 MHz 465-495 MHz 0.25 V (typical) -60 dB -70 dB 0.00025% -75 dB -70 dB 500 mW -70 dB UHF 20/25kHz

Average Battery Life Capacity 4W @ (5-5-90 Duty (mAh) Cycle): High Capacity Li-Ion 1800 14 Hrs. NiMH FM 1300 9 Hrs. NiCd Std 1100 8 Hrs. NiMH Std 1400 10 Hrs. Slim Li-Ion 1600 12 Hrs.

Sensitivity 12 dB EIA SINAD: Adjacent Channel Selectivity: Intermodulation: Freq. Stability (-30C to +60C): Spur Rejection: Image and 1/2 I-F Rejection: Audio Output @ <5% Distortion:

Self-Quieter Frequencies
UHF1
419.993750 420.000000 420.006250 (420+/-6.25kHz)

UHF2
443.93125 443.9375 443.94375 443.950 443.95625 443.9625 443.96875

UHF3
488.326250 488.332500 488.338750 488.345000 488.351250 488.357500 488.363750 488.345+/-18.75kHz

All specifications are subject to change without notice.

1-8

Model Charts and Test Specifications: MIL Standards

1.8

MIL Standards
Table 1-2. MIL STDS 810 C, D, E, and F: Applicable to UHF and VHF Specifications (8.2 and 8.4) Military Standards 810 C, D, E, & F: Parameters/Methods/Procedures 810C 810D
Methods 500.2 501.2 502.2 503.2 505.2 506.2 507.2 509.2 510.2 514.3 516.3 Procedures 2 1,2 1,2 1 1 1,2 2,3 1 1 1 1,4 Methods 500.3 501.3 502.3 503.3 505.3 506.3 507.3 509.3 510.3 514.4 516.4

810E
Procedures 2 1,2 1,2 1 1 1,2 2,3 1 1 1 1,4 Methods 500.4 501.4 501.4 503.4 505.4 506.4 507.4 509.4 510.4 514.5 516.5

810F
Procedures 1 1,2 1,2 1 1 1 3 1 1 1 1

Applicable MIL-STD Low Pressure High Temperature Low Temperature Temperature Shock Solar Radiation Rain Humidity Salt Fog Dust Vibration Shock

Methods 500.1 501.1 502.1 503.1 505.1 506.1 507.1 509.1 510.1 514.2 516.2

Procedures 1 1,2 1 1 1 1,2 2 1 1 8,10 1,2,5

Chapter 2 Theory Of Operation

2.1 2.2

Introduction
This chapter provides a basic theory of operation for the radio components.

Major Assemblies
Transceiver Board contains all transmit, receive, and audio circuitry. Display (Limited and Full Keypad models only) 8 characters (14 segments star burst) and 10 icons with backlighting, liquid-crystal display (LCD). Keypad Board (Limited and Full Keypad models only) Limited Keypad: a 2-button menu keypad with 2-way navigation button, Full Keypad: a 2-button menu keypad with 2-way navigation button, and a 3 x 4 alphanumeric keypad.Transceiver Board (Figure 2-1).

Antenna

M140 Transceiver Board Battery Spkr 3 2 J301 J460

Keypad Board 28 J2 J1 Display

J491 J470 2 Mic

Figure 2-1. Major Assemblies Block Diagram

2.2.1

Receiver
Incoming RF signals from the antenna are first routed through the harmonic filter and antenna switch, part of the transmitter circuitry, before being applied to the receiver front end. The receiver front end consists of a preselector filter, RF amplifier, interstage filter, and a double-balanced first mixer (Figure 2-2). The mixer output is applied to a diplexer network which matches the 44.85 MHz IF signal to the crystal filter, and terminates the mixer into 50 ohms at all other frequencies. The receiver back-end is a dual conversion design. High IF selectivity is provided by a 4-pole fundamental mode 44.85 MHz crystal filter. The output is matched to an IF amplifier stage. The output of the IF amplifier is applied to the input of the receiver IFIC.

2-2

Theory Of Operation: Major Assemblies

The IFIC is a low-voltage monolithic FM IF system incorporating a mixer/oscillator, two limiting IF amplifiers, quadrature detector, logarithmic received signal strength indicator (RSSI), voltage regulator and audio, and RSSI Op Amps. The second LO frequency, 44.395 MHz, is determined by a crystal oscillator. The second mixer converts the 44.85 MHz high IF frequency to 455 kHz. Additional IF selectivity is provided by two ceramic filters. The first ceramic filter is a 4-pole filter used between the second mixer and IF amp. The second ceramic filter is a 6-pole filter and is used between the IF amp and the limiter input. For the second ceramic filter, a wider filter is used for 20/25 kHz channel spacing, and a narrower filter is used for 12.5 kHz channels. A ceramic resonator provides phases vs. frequency characteristic required by the quadrature detector, with 90 degree phase shift occurring at 455 kHz. The output of the IFIC is the recovered audio signal which is fed to the audio IC for amplification and signal conditioning. The output of the audio IC is injecting into the audio PA which drives the 24 Ohm speaker.

2.2.2

Transmitter
When the radio is transmitting, microphone audio is passed through the audio IC, where preemphasis and low-pass (splatter) filtering are done. The output of the audio IC is used to modulate the TX VCO, which creates the modulated carrier. The modulated carrier is then amplified by the predriver and power amplifier circuit, which transmits the signal under dynamic power control
Ref. Osc.

Frac N

Tx VCO Circuit Loop Filter VCOBIC

Tx Predriver
Tx Out

PA Module

Rx Out

Power Cntr

Mod
Audio PA Spkr Mic Audio IC
BW_SEL 6G 6E Switching

Rx VCO Circuit T/R Switch

Harmonic Filter

Recovered Audio

Filter Preselector Cer Fltr

4E

Ceramic Resonator

Rx LNA IF Amp Crystal Filter Mixer

Demodulator

Image Filter

RSSI

IF IC

Figure 2-2. Transceiver Block Diagram

Chapter 3 Test Equipment, Service Aids, and Service Tools

3.1

Test Equipment
Table 3-1 lists test equipment required to service the CP100 Series Portable Radios. Table 3-1. Recommended Test Equipment

Motorola Part No. R2600 series

Description Comms System analyzer (non MPT)

Characteristics This item will substitute for items with an asterisk (*)

Application Frequency/deviation meter and signal generator for wide-range troubleshooting and alignment Digital voltmeter is recommended for AC/DC voltage and current measurements Audio voltage measurements Waveform measurements

*R1074_

Fluke 87 digital multi- True RMS metering, meter 200 kHz frequency counter, 32-segment bargraph with backlit display AC voltmeter Dual channel 100 MHz oscilloscope (Agillent) RF millivolt meter SINAD meter or SINAD meter with RMS Programmable DC power supply Wattmeter, Plug-in Element Plug-in Element Plug-in Element Carry case RF Dummy Load 1mV to 300mV, 10 megaohm input impedance Two-channel, 100 MHz bandwidth, 200M sample rate/sec, 2MB memory/ channel 100V to 3V RF, 10 kHz to 1 GHz frequency range Without RMS audio voltmeter or With RMS audio voltmeter 0-20V DC, 0-5 amps, current limited Thruline 50-Ohm, 5% accuracy 10W, 25 - 60 MHz 10W, 100 - 250 MHz 10W, 200 - 500 MHz Wattmeter and 6 elements

*R1377_ R1611_

S1339_ *R1013_ or *R1370_ S1348D R1440A 0180305F14 0180305F30 0180305F39 RLN4610A T1013

RF level measurements Receiver sensitivity measurements

Bench supply for 7.5 V DC Transmitter power output measurements

3-2

Test Equipment, Service Aids, and Service Tools: Service Aids

3.2

Service Aids
Table 3-2 lists service aids recommended for working on the CP100 Series Portable Radios. While all of these items are available from Motorola, most are standard shop equipment items, and any equivalent item capable of the same performance may be substituted for the item listed. Table 3-2. Service Aids

Motorola Part No. RLN4460 RLN4510 PMKN4004 PMKN4003

Description Portable Test Set Battery Interface Programming Test Cable Radio to Radio Cloning Cable

Application Enables connection to the audio/accessory jack. Allows switching for radio testing. Regulates DC current and voltage between radio and power supply. Connects radio to RIB (RLN4008). Allows a radio to be duplicated from a master radio by transferring programmed data from the master radio to the other. Enables communications between the radio and the computers serial communications adapter. Adapts radios antenna port to BNC cabling of test equipment. Interconnects radio to power supply.

RLN4008 5886564Z01 0180305K08 EPN4040_ EPN4041_ HSN9412 3080369B71 or 3080369B72

Radio Interface Box RF BNC Adaptor Shop Battery Eliminator

Wall-Mounted Power Supply (UK) Used to supply power to the RIB Wall-Mounted Power Supply (220VAC) Wall-Mounted Power Supply (120VAC) Computer Interface Cable Used to supply power to the RIB Used to supply power to the RIB Use B72 for the IBM PC AT or newer (9-pin serial port). Use B71 for older models (25-pin serial port). Connects the computers serial communications adapter to the RIB (RLN4008). Connection from computer to RIB. Used to remove the front cover assembly. Tighten and remove chassis screws Removable TORX screwdriver bit Digitally controlled soldering iron For WADN4055A Soldering iron For WADN4055A Soldering iron Used for all radio assembly/disassembly procedures

HKN9216 6680702Z01 RSX4043A 6680387A70 WADN4055A 6604008K01 6604008K02 0180386A82 6684253C72 6680384A98 1010041A86

IBM Computer Interface Cable Knob Remover/Chassis Opener TORX screwdriver T6 TORX bit Portable Soldering Station 0.4mm replacement tip 0.8mm replacement tip Anti-static Grounding Kit Straight Prober Brush Solder (RMA type)

63/37, 0.5mm diameter, 2.2kg (1lb) spool.

Test Equipment, Service Aids, and Service Tools: Service Aids

3-3

Programming/Test Cable

25 POSITION MALE CONNECTOR

25 POSITION FEMALE CONNECTOR

P2
36.0 CABLE

P3

36.0 CABLE

P1

Figure 3-1. Programming/Test Cable

P1 2.5mm stereo and 3.5mm

3.5mm Tip (Speaker +) 3.5mm Sleeve

P2 25 pin Male D Connector Components molded inside 1 5

47 ohm

Orange

Blue

24 7
33K

To Test Box

White 2.5mm Tip 5 (Microphone) 2.5mm 2.5mm Center + 1UF,16V 5% Spiral Yellow

3 4

20 8 15 16 9

P3 25 pin Female D Connector 1 15 To Test Box 4 11

4 3

2 3.5mm mono 2.5mm stereo 5

Figure 3-2. Wiring of the Connectors

3-4

Test Equipment, Service Aids, and Service Tools: Service Aids

Chapter 4 Performance Checks

4.1

General
These radios meet published specifications through their manufacturing process by utilizing highaccuracy laboratory-quality test equipment. The recommended field service equipment is as accurate as the manufacturing equipment with few exceptions. This accuracy must be maintained in compliance with the manufacturers recommended calibration schedule.

30 dB Pad Transmit Power Cable RLN4510 30 dB Pad BNC RF Generator RF Adaptor 5886564Z01 Receive Audio In Test Box RLN4460 Program/Test Cable PMKN4004

Service Monitor or Counter Wattmeter

Power Supply Battery Eliminator

Radio

Tx Rx

Audio Generator Sinad Meter AC Voltmeter

Tx Data

RIB RLN4008

Rx Data Gnd

Computer Interface Cable RIB Power Supply

Figure 4-1. Radio Tuning Setup

4.2

Power-Up Self Test

Applying power to the radio by using the on/off volume control, starts a self-test routine which checks the RAM, EEPROM hardware and EEPROM checksum. Pressing and holding SB1 while turning on the radio causes the self-test routine to check for the ROM checksum as well. If these checks are successfully completed, the radio will generate the Self-Test Pass Tone. If the self-test is not successful, a Self-Test Fail Tone is heard.

4-2

Performance Checks: RF Test Mode

Supply voltage can be connected from the battery eliminator. The equipment required for alignment procedures is connected as shown in the Radio Performance Checks Setup diagram (Figure 4-1). Initial equipment control settings should be as indicated in Table 4-1 and should be the same for all performance checks and tuner alignment procedures. Table 4-1. Initial Equipment Control Settings Service Monitor Monitor Mode: Power Monitor RF Attenuation: -70 AM, CW, FM: FM Oscilloscope Source: Mod Oscilloscope Horiz: 1 0 mSec/Div Oscilloscope Vert: 2.5kHz/Div Oscilloscope Trig: Auto Monitor Image: Hi Monitor BW: Nar Monitor Squelch: mid CW Monitor Vol: 1/4 CW Test Set Spkr set: A Spkr/load: Speaker PTT: OFF Power Supply Voltage: 7.5 Vdc DC on/standby: Standby Volt Range: 10 V Current: 2.5 A

4.3

RF Test Mode
When the PR400 radio is operating in its normal environment, the radio's microcomputer controls the RF channel selection, transmitter key-up, and receiver muting, according to the customer codeplug configuration. However, when the unit is on the bench for testing, alignment, or repair, it must be removed from its normal environment using a special routine, called RF TEST MODE. This mode allows bench testing of the radio at various test frequencies across the entire band, at both high and low transmit power (if applicable), at various channel spacings, and with different coded or carrier squelch types. Any customer specific programming in the radio will not be changed or affected by use of the RF Test Mode.

Side Button 1

P2 P1 3

Side Button 2

2 1 4 7 5 8 0

6 9 #

Figure 4-2. Side Button Locations

Performance Checks: RF Test Mode

4-3

To enter test mode: 1. Turn the radio on. Within ten seconds after the self test is complete (self test tone is heard), press SB2 (Side Button 2 in Figure 4-2) five times in succession. If the self test complete tone is not heard, see Error Codes information in Chapter 9. Entry into the test mode is indicated by a positive indicator tone followed by a good key chirp (GKC)Upon entering test mode, the radio is in the carrier squelch mode. 2. Press SB1 (Side Button 1) and scroll through and access test environments as shown in Table 42. 3. Press SB2 and scroll through the channel spacing available as shown in Table 4-3. 4. Turn the channel selector knob to change the test channel for that environment as shown in Table 4-4. 5. Press the PTT on a test channel to cause the radio to transmit at the test frequency for the channel. Table 4-2. Test Environments No. of Beeps 1 GKC* 1 BKC* 2 BKC 3 BKC 5 BKC 9 BKC Description Carrier Squelch Tone Private-Line Digital Private-Line Dual-Tone Multiple Frequency Unsquelch Open High-Speed Signaling Function RX: unsquelch if carrier detected TX: mic audio RX: unsquelch if carrier and tone (192.8 Hz) detected TX: mic audio + tone (192.8 Hz) RX: unsquelch if carrier and digital code (131) detected TX: mic audio + digital code (131) RX: unsquelch if carrier detected TX: selected DTMF tone pair RX: constant unsquelch TX: mic audio RX: unsquelch if carrrier detected TX: 1500 Hz tone

* BKC means Bad Key Chirp (low-pitched tone), GKC means Good Key Chirp (high-pitched only). Table 4-3. Test Channel Spacing No. of BKC 1 2 3 Channel Spacing 25 kHz 12.5 kHz 20 kHz

4-4

Performance Checks: RF Test Mode

Table 4-4. Test Frequencies Channel Selector Switch Position 1 Low Power 8 High Power 2 Low Power 9 High Power 3 Low Power 10 High Power 4 Low Power 11 High Power 5 Low Power 12 High Power 6 Low Power 13 High Power 7 Low Power 14 High Power Test Channel TX#1 or #8 RX#1 or #8 TX#2 or #9 RX#2 or #9 TX#3 or #10 RX#3 or #10 TX#4 or #11 RX#4 or #11 TX#5 or #12 RX#5 or #12 TX#6 or #13 RX#6 or #13 TX#7 or #14 RX#7 or #14 VHF (146-174 MHz) 146.625 150.775 155.275 160.125 164.475 169.475 173.875 UHF1 (403-440 MHz) 403.625 409.775 415.275 420.125 426.475 432.475 437.875 UHF 2 (438-470 MHz) 438.625 443.775 448.275 454.125 459.475 464.475 469.875 UHF3 (465-495 MHz) 465.625 470.775 475.275 480.125 485.475 490.475 494.875

Table 4-5. Receiver Performance Checks Test Name Reference Frequency Communications Analyzer Mode: PWR MON 4th channel test frequency* Monitor: Frequency error Input at RF In/Out Mode: GEN Output level: 1.0m V RF 4th channel test frequency* Mod: 1 kHz tone at 3 kHz deviation Monitor: DVM: AC Volts As above, except SINAD, lower the RF level for 12 dB SINAD. RF level set to 1 mV RF Radio TEST MODE, Test Channel 4 carrier squelch output at antenna Test Set PTT to continuous (during the performance check) Comments Frequency error to be 200 Hz VHF 500 Hz UHF

Rated Audio

TEST MODE PTT to OFF Test Channel 4 (center), meter carrier squelch selector to Audio PA

Set volume control to 3.46 Vrms

Distortion Sensitivity (SINAD) Noise Squelch Threshold (only radios with conventional system need to be tested)

As above, except to distortion As above As above

As above PTT to OFF (center) PTT to OFF (center), meter selection to Audio PA, spkr/ load to speaker As above

Distortion <3.0% RF input to be <0.30 V (0.25 V typical). Set volume control to 3.46 Vrms

As above

As above, except change frequency to a conventional system. Raise RF level from zero until radio unsquelches.

out of TEST MODE; select a conventional system

Unsquelch to occur at <0.25 V. Preferred SINAD = 6-9 dB

*. See Table 4-4

Performance Checks: RF Test Mode

4-5

Table 4-6. Transmitter Performance Checks Test Name Reference Frequency Communications Analyzer Mode: PWR MON 4th channel test frequency* Monitor: Frequency error Input at RF In/Out As above Mode: PWR MON 4th channel test frequency* atten to -70, input to RF In/ Out Monitor: DVM, AC Volts Set 1 kHz Mod Out level for 0.025 Vrms at test set, 80m Vrms at AC/DC test set jack Mode: PWR MON 4th channel test frequency* atten to -70, input to RF In/ Out Radio TEST MODE, Test Channel 4 carrier squelch Output at antenna As above As above Test Set PTT to continuous (during the performance check) As above As above, meter selector to mic Comments Frequency error to be 200 Hz VHF 500 Hz UHF

Power RF Voice Modulation

Refer to Maintenance Specifications Deviation: VHF, UHF 4.0 kHz but 5.0 kHz (25 kHz Ch Sp).

Voice Modulation (internal)

TEST MODE, Test Channel 4 carrier squelch Output at antenna

Remove modula- Press PTT switch on tion input radio. Say four loudly into the radio mic. Measure deviation: VHF, UHF 4.0 kHz but 5.0 kHz (25 kHz Ch Sp) As above Deviation: VHF, UHF 3.05 kHz but 3.45 kHz (25 kHz Ch Sp) Deviation: VHF, UHF 500Hz but 1000 Hz (25 kHz Ch Sp).

DTMF Modulation

As above, 4th channel test frequency*

TEST MODE, Test Channel 4 DTMF Output at antenna

PL/DPL Modulation

As above 4th channel test frequency* BW to narrow

TEST MODE, As above Test Channel 4 TPL DPL

*. See Table 4-4

4-6

Performance Checks: RF Test Mode

Notes:

Chapter 5 Radio Tuning and Programming

5.1

Introduction
This chapter provides an overview of the Commercial Series Customer Programming Software (CPS) and the Global Tuner as designed for use in a Windows 98/NT4/2000/ME/XP environment. Both cover all the functions of the traditional Radio Service Software (RSS) package. They are both available in the CPS and Global Tuner (CD ROM) Kit (RVN4191). A CPS/Tuner Installation Manual (6866550D14) is included in the Product Manual.

5.2

CPS Programming Setup

Refer to online help files for the CPS Programming procedures. (See Figure 5-1 for CPS Programming Setup).

Radio Test Box RLN4460 Battery Program/ Test Cable PMKN4004

Tx Data

RIB RLN4008

Rx Data Gnd

Computer Interface Cable RIB Power Supply

Figure 5-1. CPS Programming Setup

5-2

Radio Tuning and Programming: Radio Tuning Setup

5.3

Radio Tuning Setup

A Windows 98/NT4/2000/ME/XP PC (personal computer) and Global Tuner are required to tune the radio. To perform the tuning procedures, the radio must be connected to the PC, RIB (Radio Interface Box) and Universal Test Set as shown in Figure 5-2 below. Refer to online help files for the tuning procedures.

30 dB Pad Transmit Power Cable RLN4510 30 dB Pad BNC RF Generator RF Adaptor 5886564Z01 Receive Audio In Test Box RLN4460 Program/Test Cable PMKN4004

Service Monitor or Counter Wattmeter

Power Supply Battery Eliminator

Radio

Tx Rx

Audio Generator Sinad Meter AC Voltmeter

Tx Data

RIB RLN4008

Rx Data Gnd

Computer Interface Cable RIB Power Supply

Figure 5-2. Radio Tuning Setup

Radio Tuning and Programming: Radio-to-Radio Cloning

5-3

5.3.1

Initial Test Equipment Control Settings

The initial test equipment control settings are listed in Table 5-1. Table 5-1. Initial Equipment Control Settings
Service Monitor Test Set Power Supply

Monitor Mode: Power Monitor RF Attenuation: -70 AM, CW, FM: FM Oscilloscope Source: Mod Oscilloscope Horizontal: 10 mSec/Div Oscilloscope Vertical: 2.5 kHz/Div Oscilloscope Trigger: Auto Monitor Image: Hi Monitor BW: Nar Monitor Squelch: mid CW Monitor Volume: 1/4 CW

Speaker set: A Speaker/load: Speaker PTT: OFF

Voltage: 13.2 Vdc DC on/standby: Standby Volt Range: 20 V Current: 20 A

5.4

Radio-to-Radio Cloning
1. Cloning is the process of copying the content of one radio (source radio) into another radio (destination radio). Radio content refers to system-type features such as frequency, squelch type options, trunking, etc. Note: The source radios serial number cannot be blank. Radio functionality inherent in one radio cannot be cloned to another radio that does not contain the same functionality. Tuning and alignment information are not transferable and are not affected by cloning. 1. Signaling Identification Numbers (IDs) are duplicated in the cloning process. Unique IDs may be assigned with the CPS. Note: Unsuccessful cloning attempts generates a continuous tone and may be an indication that the destination radios codeplug is corrupted.

5-4

Radio Tuning and Programming: Radio-to-Radio Cloning

Procedure: 1. Turn source and target radios off. 2. Connect cloning cable (PMKN4003) to the side connector of both radios. 3. Turn on the destination radio. 4. Press and hold the two side buttons at the same time on the source radio and then power up the source radio (Figure 5-3). Both radios produce a clone-entry tone. 5. Release both side buttons, 1 and 2. 6. When cloning is completed, the source radio produces a clone-exit tone and both the source and destination radios reset. 7. Turn both radios off. 8. Disconnect the cloning cable from both radios and turn them on for normal operation.

Side Button 1

P2 P1 3

Side Button 2

2 1 4 7 5 8 0

6 9 #

Figure 5-3. Side Button Locations

Chapter 6 Full Keypad Model Disassembly and Re-assembly

6.1

Introduction
This section provides details about the following: Preventive maintenance (inspection and cleaning) Safe handling of CMOS and LDMOS devices Disassembly and re-assembly of the radio Repair procedures and techniques

6.2

Preventive Maintenance
The radios do not require a scheduled preventive maintenance program; however, periodic visual inspection and cleaning is recommended.

6.2.1

Inspection
Check that the external surfaces of the radio are clean, and that all external controls and switches are functional. It is not recommended to inspect the interior electronic circuitry.

6.2.2

Cleaning Procedures
The following procedures describe the recommended cleaning agents and the methods to be used when cleaning the external and internal surfaces of the radio. External surfaces include the front cover, housing assembly and battery case. These surfaces should be cleaned whenever a periodic visual inspection reveals the presence of smudges, grease, and/or grime. Note: Internal surfaces should be cleaned only when the radio is disassembled for service or repair. The only recommended agent for cleaning the external radio surfaces is a 0.5% solution of a mild dishwashing detergent in water. The only factory recommended liquid for cleaning the printed circuit boards and their components is isopropyl alcohol (70% by volume).

CAUTION: The effects of certain chemicals and their vapors can have harmful results on certain plastics. Avoid using aerosol sprays, tuner cleaners, and other chemicals.

Cleaning External Plastic Surfaces Apply the 0.5% detergent-water solution sparingly with a stiff, non-metallic, short-bristled brush to work all loose dirt away from the radio. Use a soft, absorbent, lintless cloth or tissue to remove the solution and dry the radio. Make sure that no water remains entrapped near the connectors, cracks, or crevices.

6-2

Full Keypad Model Disassembly and Re-assembly: Safe Handling of CMOS and LDMOS Devices

Cleaning Internal Circuit Boards and Components Isopropyl alcohol (70%) may be applied with a stiff, non-metallic, short-bristled brush to dislodge embedded or caked materials located in hard-to-reach areas. The brush stroke should direct the dislodged material out and away from the inside of the radio. Make sure that controls or tunable components are not soaked with alcohol. Do not use high-pressure air to hasten the drying process since this could cause the liquid to collect in unwanted places. After completing the cleaning process, use a soft, absorbent, lintless cloth to dry the area. Do not brush or apply any isopropyl alcohol to the frame, front cover, or back cover. Note: Always use a fresh supply of alcohol and a clean container to prevent contamination by dissolved material (from previous usage).

6.3

Safe Handling of CMOS and LDMOS Devices

Complementary metal-oxide semiconductor (CMOS) devices are used in this family of radios, and are susceptible to damage by electrostatic or high voltage charges. Damage can be latent, resulting in failures occurring weeks or months later. Therefore, special precautions must be taken to prevent device damage during disassembly, troubleshooting, and repair. Handling precautions are mandatory for CMOS circuits and are especially important in low humidity conditions. DO NOT attempt to disassemble the radio without first referring to the following CAUTION statement.

CAUTION: This radio contains static-sensitive devices. Do not open the radio unless you are properly grounded. Take the following precautions when working on this unit:

Store and transport all CMOS devices in conductive material so that all exposed leads are shorted together. Do not insert CMOS devices into conventional plastic snow trays used for storage and transportation of other semiconductor devices. Ground the working surface of the service bench to protect the CMOS device. We recommend using the Motorola Static Protection Assembly (part number 0180386A82), which includes a wrist strap, two ground cords, a table mat, and a floor mat. Wear a conductive wrist strap in series with a 100k resistor to ground. (Replacement wrist straps that connect to the bench top covering are Motorola part number RSX4015.) Do not wear nylon clothing while handling CMOS devices. Do not insert or remove CMOS devices with power applied. Check all power supplies used for testing CMOS devices to be certain that there are no voltage transients present. When straightening CMOS pins, provide ground straps for the apparatus used. When soldering, use a grounded soldering iron. If at all possible, handle CMOS devices by the package and not by the leads. Prior to touching the unit, touch an electrical ground to remove any static charge that you may have accumulated. The package and substrate may be electrically common. If so, the reaction of a discharge to the case would cause the same damage as touching the leads.

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6-3

6.4

Disassembling and Re-assembling the Radio General

Since these radios may be disassembled and re-assembled with the use of only four (board to casting) screws, it is important to pay particular attention to the snaps and tabs, and how parts align with each other. The following tools are required for disassembling the radio (see Chapter 3 for a list of service aids): Knob remover/chassis opener Penknife-size screwdriver TORX T6 screwdriver Scribe

If a unit requires more complete testing or service than is customarily performed at the basic level, send this unit to a Motorola Authorized Service Center. See Appendix B for a list of authorized service centers. The following disassembly procedures should be performed only if necessary: Chassis Disassembly Speaker Disassembly PTT Disassembly

6.4.1

Radio Disassembly Detailed

1. Turn off the radio. 2. Remove the battery (Figure 6-1): a. b. c. Slide the battery latch into the unlock position. Disengage by pushing downward and holding the latch towards the front of the radio. With the battery latch disengaged, slide the battery down from the top of the radio about 1/2 in. Once the battery is free from the battery rails, lift it directly away from the radio. Remove the battery from the radio.

6.4.1.1 Front Cover From Chassis Disassembly

Lock

Unlock

Battery Latch

Figure 6-1. Battery Removal

6-4

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

3. Remove the antenna. 4. Pry off the volume and channel selector knobs from their shafts using the knob removal/chassis opener tool (Motorola part # 6686533Z01). (Figure 6-2).

Figure 6-2. Antenna and Knob Removal

Note: Both knobs slide on and off. However the knobs are designed to fit very tightly on the shaft. 5. Separate the chassis from the front housing assembly by using the knob remover/chassis opener too. Place the broad side of the opener into the slots located at the base of the radio (Figure 6-3). Press the handle on the opener downwards. This pressing action forces the thin inner plastic wall toward the base of the radio, releasing the two chassis base tabs.

Knob Remover/ Chassis Opener

Radio Chassis

Figure 6-3. Chassis Removal

CAUTION: Marring the front cover O-ring sealing area will prevent the radio from sealing properly. If the O-ring is damaged, replace it with a new one.

6. Pull the chassis assembly out of the front cover only until the volume and channel selectors shaft just clear the top of the case. (Figure 6-4).

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6-5

Note: The speaker wire assembly microphone wire assembly and keypad flex cable connector connecting the front housing assembly and the chassis prevent the two units from being completely separated 7. Rotate the bottom of the chassis up about 20 to disconnect the keyboard flex cable connector. Push down 2 end tabs to release flex connector at the bottom of the chassis.

Radio Chassis

Flex Connector

Figure 6-4. Keyboard Flex Connection 8. Rotate the chassis counterclockwise out of the housing and position next to the housing. Take care not to damage the speaker and microphone wires that are still connected to the chassis (Figure 6-5).

Speaker Connector

Microphone Connector

Figure 6-5. Microphone and Speaker Connections 9. Unplug the speaker wire assembly from the 2-pin connector on the chassis. 10. Unplug the microphone wire assembly from the socket on the chassis. 11. Move the chassis away from the housing and place on a clean work surface.

6-6

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6.4.1.2 Dust Cover Disassembly

1. Gently pry the top of the dust cover away from the body of the radio. (See Figure 6-6). 2. Rotate the dust cover 90 in a counterclockwise direction to allow the key to be removed. 3. Separate the dust cover away from the body of the radio. The dust cover key is fragile; apply only light pressure to the key while removing the dust cover.
key

a. Pry dust cover from body.

b. Rotate dust cover 90 to allow key to be removed. Figure 6-6. Dust Cover Disassembly

c. Separate dust cover from body.

6.4.1.3 Speaker and Microphone Disassembly

Note: The speaker is held in place with a retainer bracket. Be careful not to damage the speaker when removing the retainer bracket. 1. Remove the screw from the speaker retainer using a T6 Torx screwdriver (Figure 6-7). 2. Lift the retainer off the speaker, sliding end of retainer out of corner slot on the housing. 3. Lift the speaker out from the front housing. 4. Carefully lift microphone assembly out of housing.

Retainer Bracket

Speaker Speaker Connector

Microphone

Radio Housing Microphone Connector

Figure 6-7. Removal Speaker-Microphone Assembly

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6-7

6.4.1.4 Keyboard Removal

1. Carefully pry the four keypad retainer locking tabs free from the housing use a scribe. Note: Use care when removing the keypad retainer to prevent damage to the keyboard flex cable. 2. Lift the keypad retainer up from the bottom and slide the top tabs out. 3. Slide keypad retainer out of chassis carefully to prevent damage to flex cable.

CAUTION: Refer to the CMOS CAUTION paragraph (6.3) before removing the main board. Be sure to use Electrostatic Discharge protection when handling circuit boards.

4. Lift LCD keypad board out of housing (Figure 6-8). 5. Lift keypad out of housing.

Keypad Retainer

Flex Cable

Keypad Board

Keypad

Figure 6-8. Keypad Removal

6.4.1.5 PTT Disassembly

1. If required, the PTT (Figure 6-9 can be disassembly using a small screwdriver, as follows: a. b. c. d. Insert the tip of a small screwdriver underneath the PTT and unsnap the top tab. Pry the PTT away from the radio housing. Inspect the two hooks. If bent or broken, the PTT must be replaced. Remove the PTT seal.

6-8

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

Tab Hooks Flat Blade Screwdriver

PTT Seal Tab

Figure 6-9. PTT Removal

6.4.1.6 Chassis Disassembly

!
.

CAUTION: Refer to the CMOS CAUTION paragraph (see 3.3) before removing the main board. Be sure to use Electrostatic Discharge protection when handling circuit boards.

1. Remove the O-ring. 2. Use a Torx screwdriver with a T6 bit to remove the four screws (Figure 6-10) holding the main board to the chassis.

Audio Jack Shroud

Main Board

Radio Chassis

O-Ring

Figure 6-10. Removal of Main Board from Chassis 3. The audio jack shroud can be removed from the main board. 4. Lift the main board from the chassis (Figure 6-10). 5. Remove the battery contact seal.

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6-9

6.4.2

Radio Re-assembly - Detailed

1. Insert the tail of the dust cap into the bottom hole of the audio jacks housing opening (Figure 6-11). 2. Press the dust cap until the tail is fully into the hole. Note: Make sure the dust cap is placed between the keypad retainer mounting post and the side wall of the radio. 3. Twist the dust cap counter-clockwise until the cap is seated properly onto the recess. 4. Press the cap again to ensure it fully covers the opening for the audio jack. .

6.4.2.1 Dust Cover Re-assembly

Figure 6-11. Dust Cap Re-assembly

6.4.2.2 Microphone and Speaker Re-assembly

1. Check that the mic and speaker felts are in position and not damaged. If damaged replace felts. 2. Insert the microphone sub-assembly into the microphone boot. 3. 3. Insert the Boot and microphone sub-assembly into the microphone recess in the housing and route wires as shown in Figure 6-12.

6-10

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

Microphone Boot

Microphone Recess

Microphone Position

Figure 6-12. Microphone Re-assembly 4. Locate the speaker tab and align it with the tab opening in the front housing (Figure 6-13). 5. Insert the speaker tab into the speaker recess in the housing. Ensure the speaker is seated flush in the housing. Note: Make sure the speaker and microphone wires are routed tightly between the speaker basket and the housing post. 6. Insert one end of the speaker retainer into the slot in the front housing (See Figure 6-13).

Speaker Retainer

Speaker

Speaker Tab Tab Opening

Front Housing Slot

Figure 6-13. Speaker Re-assembly Note: When fastening the speaker retainer screw, make sure the wires are out of the way to prevent pinching by the retainer. 7. Install the retainer screw using a T6 Torx screwdriver. Torque to 0.26 - 0.28Nm (2.3 - 2.5 lb/in).

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6-11

6.4.2.3 Keypad and LCD/Keyboard Re-assembly

1. Attach the flex cable from the LCD module to the keyboard, if not already attached (Figure 6-15). 2. Remove protective mylar from window and from keypad, if present. 3. Install the new keypad into the housing. Use the two housing posts for keypad alignment (Figure 6-14).

Full Keypad

Housing Posts

Figure 6-14. Keypad Re-assembly 4. Remove mylar from LCD if present.

CAUTION: Make sure the microphone and speaker wires are not trapped under the LCD module.

5. Install the LCD/Keypad sub-assembly into the housing (Figure 6-15).

Flex Cable from LCD Module Flex Cable to Main PC Board

Figure 6-15. LCD/Keypad Board Re-assembly

6-12

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6. Attach the flex cable into the connector on the keypad board, if not already connected. 7. Bend the flex cable as shown (Figure 6-15)

6.4.2.4 Keyboard Retainer Re-assembly

1. Insert the flex cable through the slot at the bottom of the keyboard retainer (Figure 6-16).

Figure 6-16. Keyboard Retainer Re-assembly 2. Insert the two top tabs of the keyboard retainer into the two tab retainers located on each side of the speaker in the front housing (Figure 6-16). 3. Press the four keypad retainer locking tabs into the housing. 4. Push the speaker and microphone wires into the top left hand corner of the housing.

6.4.2.5 Chassis Assembly/Re-assembly

1. Replace the battery contact seal (if necessary) surrounding the battery contact (Figure 6-17). 2. Remove the old Interface Pad from the chassis by scraping off the pad and adhesive with a straight razor. Use rubbing alcohol and a cloth to completely remove the adhesive from the chassis surface. With the chassis clean and dry, add a new Interface Pad to the chassis. 3. Place the main circuit board straight down on top of the chassis with the frequency and volume switches facing down (Figure 6-17). Note: Be sure the battery contact seal protrudes through the chassis and is not pinched under the chassis. 4. Use the T6 Torx screwdriver to fasten the screws holding the main board to the chassis. Tighten to 0.42 - 0.44Nm (3.7 - 3.9 in/lb). 5. Replace the O-ring by positioning it in the top groove by the volume/frequency switches. Stretch the O-ring to place it into the retaining groove at the bottom end of the chassis. 6. Check that the O-ring is not twisted and being held by the top and bottom chassis groves.

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6-13

Frequency & Volume Switches

Audio Jack Shroud (Replace after Plugging in Speaker and Mic)

Main Board

Interface Pad Flex Cable Connector

Radio Chassis Battery Contact Seal O-Ring

Figure 6-17. Main Board onto Chassis Re-assembly

6.4.2.6 Chassis and Front Cover Re-assembly

1. Dress and connect the speaker wires. Note: Care should be taken when dressing the speaker and microphone wires to avoid pinching them between the speaker magnet and shield, or between the accessory connector and housing. Note: Ensure that the plug orientation is correct with the exposed pins in the wire casing facing upward and fully plugged in. a. Connect the speaker wire assembly into the 2-pin connector on the main board and bend the wires at the board connector so the wires are positioned toward the top of the radio (Figure 6-18). Connect the microphone wire assembly into the two hole socket on the main board and bend the wires at the board connector so the wires are positioned toward the top of the radio (Figure 6-18). Slide the audio jack shroud onto accessory connector (Figure 6-17).

b.

c.

6-14

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

Microphone Connector

Speaker Connector

Shroud

Figure 6-18. Microphone and Speaker Wires Re-assembly 2. Position the radio (Figure 6-19), and reconnect the flex connector from the keyboard into the connector located on the bottom of the main board, pushing up the 2 end tabs. 3. Slide the volume potentiometer and frequency switch shafts into their respective holes in the front cover. Look through the accessory connector opening to make certain that the wires are not pinched, between shroud and housing.

Radio Chassis

End Tabs

Flex Cable Connector

Figure 6-19. Keyboard Flex Cable Connection 4. Push the topside of the board chassis upward until it touches the housing end. Before snapping the board into the housing, perform the following checks: a. b. c. Open the dust cap and ensure the wires are not pinched between the shroud and housing. Ensure the O-ring is seated in the groove. Ensure that the bottom side of the dust cap is fully pressed into the housing before the snapping the board into place.

Full Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

6-15

5. Snap chassis assembly completely into the top of the front cover (Figure 6-20) until it settles in place.

Radio Chassis

Figure 6-20. Fastening the Chassis 6. Make sure the 0-ring is properly seated. If the O-ring seal is pinched, separate the chassis from the housing using the knob removal/chassis opener and dress O-ring properly. 7. Snap the bottom of the chassis into the front cover. 8. Check that O-ring is visible at the corners. 9. Re-assemble the knobs, antenna, and battery.

6.4.2.7 PTT Re-assembly

1. Place the PTT seal over the ridge around the top hole. Press down to seat the seal around the ridge. 2. Place the bottom tab in the slot inside the front housing PTT opening. Slightly slide down the PTT and bow it by placing one finger under the middle of the PTT, so that the top tab can be aligned and inserted into the top slot (Figure 6-21a). 3. Press the PTT assembly against the front cover opening (Figure 6-21b).

a. Place bottom tab into bottom slot. Place top tab into top slot.

b. Push down on PTT toward bottom of radio so hooks do not get crushed.

Figure 6-21. PTT Re-assembly

6-16

Full Keypad Model Disassembly and Re-assembly: Mechanical View and Parts List

6.5
6.5.1

Mechanical View and Parts List

CP180 Full-Keypad Exploded View and Parts List

2 34 3 33 32 30 29 9 10 11 12 13 14 15 16 31 17 18 28 27 26 25 24 23 22 21 20 19 4 5 6 7 8

Figure 6-22. CP180 Full Keypad Radio Exploded View

Mechanical View and Parts List

6-17

Item
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Motorola Part Number

See Section 6 3680530Z02 1386440Z01 1386440Z02 Not Field Repairable 1586391Z03 3586621Z01 3886489Z01 4586439Z01 5085738Z08 4286620Z01 3586621Z02 0780608V01 5085880L01 5104949J16 0104017J18 1586437Z01 3286431Z02 7586436Z01 2786389Z01 3286435Z01 Refer to Chap 1 Model Charts 0304726J05 4286648Z01 0909059E19 0986632Z02 7586654Z03 5586445Z02 4105944K01 3886441Z01 3286432Z01 0386434Z01 3386443Z01 6186446Z02 3680529Z01

Description
Antenna Knob, Frequency Escutcheon, Top; 4 Ch. Escutcheon, Top; 16 Ch. Antenna Adaptor/Seal (Optional) Housing, Full, with Lens Speaker, Felt PTT, Rubber PTT, Plastic Speaker Retainer Speaker Felt, Microphone Boot, Microphone Microphone Display, LCD Module Keypad Board Assy Shroud, Audio Jack Seal, Main O-ring Pad, PA Interface Chassis Seal, Battery Contact Block Back Cover Kit (Main Board + chassis) Screws, Chassis; 4 Used Plate, Retainer Connector, 28-pin 9 Pin Connector Keypad, Full Latch Assembly Spring, Latch; 2 Used Cap, Dust Seal, Control Shaft Screw, Speaker Retainer Label, Escutcheon Seal Lightpipe Knob, Volume

Item

Motorola Part Number

Description

NON-REFERENCED ITEMS 3386625Z01 3386623Z07 Nameplate, Motorola Nameplate, CP180

6-18

Full Keypad Model Disassembly and Re-assembly: Mechanical View and Parts List

Notes:

Chapter 7 Limited Keypad Model Disassembly and Re-assembly

7.1

Introduction
This section provides details about the following: Preventive maintenance (inspection and cleaning) Safe handling of CMOS and LDMOS devices Disassembly and re-assembly of the radio Repair procedures and techniques

7.2

Preventive Maintenance
The radios do not require a scheduled preventive maintenance program; however, periodic visual inspection and cleaning is recommended.

7.2.1

Inspection
Check that the external surfaces of the radio are clean, and that all external controls and switches are functional. It is not recommended to inspect the interior electronic circuitry.

7.2.2

Cleaning Procedures
The following procedures describe the recommended cleaning agents and the methods to be used when cleaning the external and internal surfaces of the radio. External surfaces include the front cover, housing assembly and battery case. These surfaces should be cleaned whenever a periodic visual inspection reveals the presence of smudges, grease, and/or grime. Note: Internal surfaces should be cleaned only when the radio is disassembled for service or repair. The only recommended agent for cleaning the external radio surfaces is a 0.5% solution of a mild dishwashing detergent in water. The only factory recommended liquid for cleaning the printed circuit boards and their components is isopropyl alcohol (70% by volume).

CAUTION: The effects of certain chemicals and their vapors can have harmful results on certain plastics. Avoid using aerosol sprays, tuner cleaners, and other chemicals.

Cleaning External Plastic Surfaces Apply the 0.5% detergent-water solution sparingly with a stiff, non-metallic, short-bristled brush to work all loose dirt away from the radio. Use a soft, absorbent, lintless cloth or tissue to remove the solution and dry the radio. Make sure that no water remains entrapped near the connectors, cracks, or crevices.

7-2

Limited Keypad Model Disassembly and Re-assembly: Safe Handling of CMOS and LDMOS Devices

Cleaning Internal Circuit Boards and Components Isopropyl alcohol (70%) may be applied with a stiff, non-metallic, short-bristled brush to dislodge embedded or caked materials located in hard-to-reach areas. The brush stroke should direct the dislodged material out and away from the inside of the radio. Make sure that controls or tunable components are not soaked with alcohol. Do not use high-pressure air to hasten the drying process since this could cause the liquid to collect in unwanted places. After completing the cleaning process, use a soft, absorbent, lintless cloth to dry the area. Do not brush or apply any isopropyl alcohol to the frame, front cover, or back cover. Note: Always use a fresh supply of alcohol and a clean container to prevent contamination by dissolved material (from previous usage).

7.3

Safe Handling of CMOS and LDMOS Devices

Complementary metal-oxide semiconductor (CMOS) devices are used in this family of radios, and are susceptible to damage by electrostatic or high voltage charges. Damage can be latent, resulting in failures occurring weeks or months later. Therefore, special precautions must be taken to prevent device damage during disassembly, troubleshooting, and repair. Handling precautions are mandatory for CMOS circuits and are especially important in low humidity conditions. DO NOT attempt to disassemble the radio without first referring to the following CAUTION statement.

CAUTION: This radio contains static-sensitive devices. Do not open the radio unless you are properly grounded. Take the following precautions when working on this unit:

Store and transport all CMOS devices in conductive material so that all exposed leads are shorted together. Do not insert CMOS devices into conventional plastic snow trays used for storage and transportation of other semiconductor devices. Ground the working surface of the service bench to protect the CMOS device. We recommend using the Motorola Static Protection Assembly (part number 0180386A82), which includes a wrist strap, two ground cords, a table mat, and a floor mat. Wear a conductive wrist strap in series with a 100k resistor to ground. (Replacement wrist straps that connect to the bench top covering are Motorola part number RSX4015.) Do not wear nylon clothing while handling CMOS devices. Do not insert or remove CMOS devices with power applied. Check all power supplies used for testing CMOS devices to be certain that there are no voltage transients present. When straightening CMOS pins, provide ground straps for the apparatus used. When soldering, use a grounded soldering iron. If at all possible, handle CMOS devices by the package and not by the leads. Prior to touching the unit, touch an electrical ground to remove any static charge that you may have accumulated. The package and substrate may be electrically common. If so, the reaction of a discharge to the case would cause the same damage as touching the leads.

Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General 7-3

7.4

Disassembling and Re-assembling the Radio General

Since these radios may be disassembled and Re-assembled with the use of only four (board to casting) screws, it is important to pay particular attention to the snaps and tabs, and how parts align with each other. The following tools are required for disassembling the radio (see Chapter 3 for a list of service aids): knob remover/chassis opener penknife-size screwdriver TORX T6 screwdriver scribe

If a unit requires more complete testing or service than is customarily performed at the basic level, send this unit to a Motorola Authorized Service Center. See Appendix B for a list of authorized service centers. The following disassembly procedures should be performed only if necessary: Chassis Disassembly Speaker Disassembly PTT Disassembly

7.4.1

Radio Disassembly Detailed

1. Turn off the radio. 2. Remove the battery (Figure 7-1): a. b. Slide the battery latch into the unlock position. Disengage by pushing downward and holding the latch towards the front of the radio. With the battery latch disengaged, slide the battery down from the top of the radio about 1cm (1/2 in). Once the battery is free from the battery rails, lift it directly away from the radio. Remove the battery from the radio.

7.4.1.1 Front Cover from Chassis Disassembly

c.

3. Remove the antenna.

Lock

Unlock

Battery Latch

Figure 7-1. Battery Removal

7-4 Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

4. Pry off the volume and channel selector knobs from their shafts using the knob remover/chassis opener tool (Motorola part # 6686533Z01) (Figure 7-2).

Figure 7-2. Antenna and Knob Removal Note: Both knobs slide on and off. However, the knobs are designed to fit very tightly on the shaft. 5. Separate the chassis from the front housing assembly by using the knob remover/chassis opener tool. Place the broad side of the opener into the slots located at the base of the radio (Figure 7-3). Press the handle of the opener downwards. This pressing action forces the thin inner plastic wall toward the base of the radio, releasing the two chassis base tabs

Knob Remover/ Chassis Opener

Radio Chassis

Figure 7-3. Chassis Removal .

CAUTION: Marring the front cover O-ring sealing area will prevent the radio from sealing properly. If the O-ring is damaged, replace it with a new one.

Note: The speaker wire assembly microphone wire assembly and keypad flex cable connecting the front housing assembly and the chassis prevent the two units from being completely separated.

Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General 7-5

6. Pull the chassis assembly out of the front cover only until the volume and channel selectors shaft just clear the top of the case. (Figure 7-4). 7. Rotate the bottom of the chassis up about 20 to access the keyboard flex connector. Push down 2 end tabs to release flex connector at the bottom of the chassis.

Radio Chassis

Flex Connector

Figure 7-4. Keyboard Flex Connector 8. Rotate the chassis counterclockwise out of the housing and position next to the housing. Take care not to damage the speaker and microphone wires that are still connected to the chassis (Figure 7-5).

Speaker Connector

Microphone Connector

Figure 7-5. Microphone and Speaker Connections 9. Unplug the speaker wire assembly from the 2-pin connector on the chassis. 10. Unplug the microphone wire assembly from the socket on the chassis. 11. Move the chassis away from the housing and place on a clean work surface.

7-6 Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

7.4.1.2 Dust Cover Disassembly

1. Gently pry the top of the dust cover away from the body of the radio. (See Figure 7-6). 2. Rotate the dust cover 90 in a counterclockwise direction to allow the key to be removed. 3. Separate the dust cover away from the body of the radio. The dust cover key is fragile; apply only light pressure to the key while removing the dust cover.
key

a. Pry dust cover from body.

b. Rotate dust cover 90 to allow key to be removed. Figure 7-6. Dust Cover Disassembly

c. Separate dust cover from body.

7.4.1.3 Speaker and Microphone Disassembly

Note: The speaker is held in place with a retainer bracket. Be careful not to damage the speaker when removing the retainer bracket. 1. Remove the screw from the speaker retainer using a T6 Torx screwdriver (Figure 7-7). 2. Lift the retainer off the speaker, sliding end of retainer out of corner slot on the housing. 3. Lift the speaker out from the front housing. 4. Carefully lift microphone assembly out of housing.

Retainer Bracket

Speaker

Speaker Connector

Microphone

Radio Housing Microphone Connector

Figure 7-7. Removal Speaker-Microphone Assembly

Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General 7-7

7.4.1.4 Keyboard Removal

1. Carefully pry the four keypad retainer locking tabs free from the housing use a scribe. Note: Use care when removing the keypad retainer to prevent damage to the keyboard flex cable. 2. Lift the keypad retainer up from the bottom and slide the top tabs out. 3. Slide keypad retainer out of chassis carefully to prevent damage to flex cable.

CAUTION: Refer to the CMOS CAUTION paragraph (7.3) before removing the main board. Be sure to use Electrostatic Discharge protection when handling circuit boards.

4. Lift LCD keypad board out of housing (Figure 7-8). 5. Lift keypad out of housing

Keypad Retainer

Flex Cable

Keypad Board

Keypad

Figure 7-8. Keypad Removal

7-8 Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

7.4.1.5 PTT Disassembly

1. If required, the PTT (Figure 7-9) can be disassembly using a small screwdriver, as follows: a. b. c. d. Insert the tip of a small screwdriver underneath the PTT and unsnap the top tab. Pry the PTT away from the radio housing. Inspect the two hooks. If bent or broken, the PTT must be replaced. Remove the PTT seal.

Tab Hooks

Screwdriver

PTT Seal Tab

Figure 7-9. PTT Removal

7.4.2

Chassis Disassembly
CAUTION: Refer to the CMOS CAUTION paragraph (see 3.3) before removing the main board. Be sure to use Electrostatic Discharge protection when handling circuit boards.

1. Remove the O-ring. 2. Use a Torx screwdriver with a T6 bit to remove the four screws (Figure 7-10) holding the main board to the chassis. 3. The audio jack shroud can be removed from the main board. 4. Lift the main board from the chassis (Figure 7-10). 5. Remove the battery contact seal.

Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General 7-9

Audio Jack Shroud

Main Board

Flex Cable Connector Radio Chassis

O-Ring

Figure 7-10. Removal of Main Board from Chassis

7.4.3

Radio Re-assembly - Detailed

1. Insert the tail of the dust cap into the bottom hole of the audio jacks housing opening (Figure 711). 2. Press the dust cap until the tail is fully into the hole. Note: Make sure the dust cap is placed between the keypad retainer mounting post and the side wall of the radio. 3. Twist the dust cap counter-clockwise until the cap is seated properly onto the recess. 4. Press the cap again to ensure it fully covers the opening for the audio jack.

7.4.3.1 Dust Cover Re-assembly

Figure 7-11. Dust Cap Re-assembly

7.4.3.2 Microphone and Speaker Re-assembly

1. Check that the mic and speaker felts are in position and not damaged. If damaged replace felts. 2. Insert the microphone sub-assembly into the microphone boot.

7-10 Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

3. Insert the Boot and microphone sub-assembly into the microphone recess in the housing and route wires as shown in Figure 7-12.
Microphone Boot

Microphone Recess

Microphone Position

Figure 7-12. Microphone Re-assembly 4. Locate the speaker tab and align it with the tab opening in the front housing (Figure 7-13). 5. Insert the speaker tab into the speaker recess in the housing. Ensure the speaker is seated flush in the housing. Note: Make sure the speaker and microphone wires are routed tightly between the speaker basket and the housing post 6. Insert one end of the speaker retainer into the slot in the front housing (See Figure 7-13).

Speaker Retainer

Speaker

Speaker Tab

Front Housing Slot

Tab Opening

Figure 7-13. Speaker Re-assembly Note: When fastening the speaker retainer screw, make sure the wires are out of the way to prevent pinching by the retainer. 7. Install the retainer screw using a T6 Torx screwdriver. Torque to 0.26 - 0.28Nm (2.3 - 2.5 lb/in).

Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General 7-11

7.4.3.3 Keypad and LCD/Keyboard Re-assembly

1. Attach the flex cable connector from the LCD module to the keyboard, if not already attached (Figure 7-15). 2. Remove protective mylar from window and from keypad, if present. 3. Install the new keypad into the housing. Use the two housing posts for keypad alignment (Figure 7-14)
Limited Keypad

Housing Posts

Figure 7-14. Keypad Re-assembly 4. Remove mylar from LCD if present. 5. Install the LCD/Keypad sub-assembly into the housing (Figure 7-15).

Flex Cable from LCD Module Flex Cable to Main PC Board

Figure 7-15. LCD/Keypad Board Re-assembly 6. Attach the flex cable connector into the connector on the keypad board, if not already connected.

CAUTION: Make sure the microphone and speaker wires are not trapped under the LCD mod-

ule.

7. Bend the flex cable connector as shown (Figure 7-15).

7-12 Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

7.4.3.4 Keyboard Retainer Re-assembly

1. Insert the flex cable connector through the slot at the bottom of the keyboard retainer (Figure 716).

Figure 7-16. Keyboard Retainer Re-assembly 2. Insert the two top tabs of the keyboard retainer into the two tab retainers located on each side of the speaker in the front housing (Figure 7-16). 3. Press the four keypad retainer locking tabs into the housing. 4. Push the speaker and microphone wires into the top left hand corner of the housing.

7.4.3.5 Chassis Assembly/Re-assembly

1. Replace the battery contact seal (if necessary) surrounding the battery contact (Figure 7-17). 2. Remove the old Interface Pad from the chassis by scraping off the pad and adhesive with a straight razor. Use rubbing alcohol and a cloth to completely remove the adhesive from the chassis surface. With the chassis clean and dry, add a new Interface Pad to the chassis. 3. Place the main circuit board straight down on top of the chassis with the frequency and volume switches facing down (Figure 7-17). Note: Be sure the battery contact seal protrudes through the chassis and is not pinched under the chassis. 4. Use the T6 Torx screwdriver to fasten the screws holding the main board to the chassis. Tighten to 0.42 - 0.44Nm (3.7 - 3.9 in/lb). 5. Replace the O-ring by positioning it in the top groove by the volume/frequency switches. Stretch the O-ring to place it into the retaining groove at the bottom end of the chassis. 6. Check the top corner of the chassis by flipping the O-ring, if the O-ring comes out easily, twist the O-ring and re-try until the O-ring is held properly by the chassis

Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General 7-13

Frequency & Volume Switches

Audio Jack Shroud (Replace after Plugging in Speaker and Mic)

Main Board

Interface Pad

Radio Chassis Battery Contact Seal O-Ring

Figure 7-17. Installation of Main Board onto Chassis

7.4.3.6 Chassis and Front Cover Re-assembly

1. Dress and connect the speaker wires. Note: Care should be taken when dressing the speaker and microphone wires to avoid pinching them between the speaker magnet and shield, or between the accessory connector and housing. Note: Ensure that the plug orientation is correct with the exposed pins in the wire casing facing upward and fully plugged in. a. Connect the speaker wire assembly into the 2-pin connector on the main board and bend the wires at the board connector so the wires are positioned toward the top of the radio (Figure 7-18). Connect the microphone wire assembly into the two hole socket on the main board and bend the wires at the board connector so the wires are positioned toward the top of the radio (Figure 7-18). Slide the audio jack shroud onto accessory connector (Figure 7-17).

b.

c.

7-14 Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

Microphone Connector

Speaker Connector

Shroud

Figure 7-18. Microphone and Speaker Wires 2. Position the radio (Figure 7-19) and reconnect the flex cable connector from the keyboard into the connector located on the bottom of the main board, pushing up the 2 end tabs. 3. Slide the volume potentiometer and frequency switch shafts into their respective holes in the front cover. Look through the accessory connector opening to make certain that the wires are not pinched, between the shroud and housing.

Radio Chassis

End Tabs

Flex Cable Connector

Figure 7-19. Keyboard Flex Cable Connection 4. Push the topside of the board chassis upward until it touches the housing end. Before snapping the board into the housing, perform the following checks: a. b. c. Open the dust cap and ensure the wires are not pinched between the shroud and housing. Ensure the O-ring is seated in the groove. Ensure that the bottom side of the dust cap is fully pressed into the housing before the snapping the board into place.

Limited Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General 7-15

5. Snap chassis assembly completely into the top of the front cover (Figure 7-20) until it settles in place.

Radio Chassis

Figure 7-20. Fastening the Chassis 6. Make sure the 0-ring is properly seated. If the O-ring seal is pinched, separate the chassis from the housing using the knob removal/chassis opener and dress O-ring properly. 7. Snap the bottom of the chassis into the front cover. 8. Check that O-ring is visible at the corners. 9. Re-assemble the knobs, antenna, and battery.

7.4.3.7 PTT Re-assembly

1. Place the PTT seal over the ridge around the top hole. Press down to seat the seal around the ridge. 2. Place the bottom tab in the slot inside the front housing PTT opening. Slightly slide down the PTT and bow it by placing one finger under the middle of the PTT, so that the top tab can be aligned and inserted into the top slot (Figure 7-21a). 3. Press the PTT assembly against the front cover opening (Figure 7-21b).

a. Place bottom tab into bottom slot. Place top tab into top slot.

b. Push down on PTT toward bottom of radio so hooks do not get crushed.

Figure 7-21. PTT Re-assembly

7-16

Limited Keypad Model Disassembly and Re-assembly: Mechanical View and Parts List

7.5
7.5.1

Mechanical View and Parts List

CP160 Limited-Keypad Exploded View and Parts List

2 34 3 33 32 30 29 9 10 11 12 13 14 15 16 31 17 18 28 27 26 25 24 23 22 21 20 19 4 5 6 7 8

Figure 7-22. CP160 Limited Keypad Radio Exploded View

Mechanical View and Parts List

7-17

Item
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

Motorola Part Number

See Section 6 3680530Z02 1386440Z03 1386440Z02 Not Field Repairable 1586391Z02 3586621Z01 3886489Z01 4586439Z01 5085738Z08 4286620Z01 3586621Z02 0780608V01 5085880L01 5104949J16 0104017J19 1586437Z01 3286431Z02 7586436Z01 2786389Z01 3286435Z01 Ref. Chap 1 Model Charts 0304726J05 4286648Z01 0986615Z02 0986632Z02 7586654Z02 5586445Z02 4105944K01 3886441Z01 3286432Z01 0386434Z01 3386443Z01 6186446Z02 3680529Z01

Description
Antenna Knob, Frequency Escutcheon, Top; 4 Ch. Escutcheon, Top; 16 Ch. Antenna Adaptor/Seal (Optional) Housing, Limited, with Lens Speaker, Felt PTT, Rubber PTT, Plastic Speaker Retainer Speaker Felt, Microphone Boot, Microphone Microphone Display, LCD Module Keypad Board Assy Shroud, Audio Jack Seal, Main O-ring Pad, PA Interface Chassis Seal, Battery Contact Block Back Cover Kit (Main Board + chassis) Screws, Chassis; 4 Used Plate, Retainer Connector, 28-pin Connector, 9-pin Keypad, Limited Latch Assembly Spring, Latch; 2 Used Cap, Dust Seal, Control Shaft Screw, Speaker Retainer Label, Escutcheon Seal Lightpipe Knob, Volume

Item

Motorola Part Number

Description

NON-REFERENCED ITEMS 3386625Z01 3386623Z06 Nameplate, Motorola Nameplate, CP160

7-18

Limited Keypad Model Disassembly and Re-assembly: Mechanical View and Parts List

Notes:

Chapter 8 Non-Keypad Model Disassembly and Re-assembly

8.1

Introduction
This section provides details about the following: Preventive maintenance (inspection and cleaning) Safe handling of CMOS and LDMOS devices Disassembly and re-assembly of the radio Repair procedures and techniques

8.2

Preventive Maintenance
The radios do not require a scheduled preventive maintenance program; however, periodic visual inspection and cleaning is recommended.

8.2.1

Inspection
Check that the external surfaces of the radio are clean, and that all external controls and switches are functional. It is not recommended to inspect the interior electronic circuitry.

8.2.2

Cleaning Procedures
The following procedures describe the recommended cleaning agents and the methods to be used when cleaning the external and internal surfaces of the radio. External surfaces include the front cover, housing assembly and battery case. These surfaces should be cleaned whenever a periodic visual inspection reveals the presence of smudges, grease, and/or grime. Note: Internal surfaces should be cleaned only when the radio is disassembled for service or repair. The only recommended agent for cleaning the external radio surfaces is a 0.5% solution of a mild dishwashing detergent in water. The only factory recommended liquid for cleaning the printed circuit boards and their components is isopropyl alcohol (70% by volume).

CAUTION: The effects of certain chemicals and their vapors can have harmful results on certain plastics. Avoid using aerosol sprays, tuner cleaners, and other chemicals.

Cleaning External Plastic Surfaces Apply the 0.5% detergent-water solution sparingly with a stiff, non-metallic, short-bristled brush to work all loose dirt away from the radio. Use a soft, absorbent, lintless cloth or tissue to remove the solution and dry the radio. Make sure that no water remains entrapped near the connectors, cracks, or crevices.

8-2

Non-Keypad Model Disassembly and Re-assembly: Safe Handling of CMOS and LDMOS Devices

Cleaning Internal Circuit Boards and Components Isopropyl alcohol (70%) may be applied with a stiff, non-metallic, short-bristled brush to dislodge embedded or caked materials located in hard-to-reach areas. The brush stroke should direct the dislodged material out and away from the inside of the radio. Make sure that controls or tunable components are not soaked with alcohol. Do not use high-pressure air to hasten the drying process since this could cause the liquid to collect in unwanted places. After completing the cleaning process, use a soft, absorbent, lintless cloth to dry the area. Do not brush or apply any isopropyl alcohol to the frame, front cover, or back cover. Note: Always use a fresh supply of alcohol and a clean container to prevent contamination by dissolved material (from previous usage).

8.3

Safe Handling of CMOS and LDMOS Devices

Complementary metal-oxide semiconductor (CMOS) devices are used in this family of radios, and are susceptible to damage by electrostatic or high voltage charges. Damage can be latent, resulting in failures occurring weeks or months later. Therefore, special precautions must be taken to prevent device damage during disassembly, troubleshooting, and repair. Handling precautions are mandatory for CMOS circuits and are especially important in low humidity conditions. DO NOT attempt to disassemble the radio without first referring to the following CAUTION statement.

CAUTION: This radio contains static-sensitive devices. Do not open the radio unless you are properly grounded. Take the following precautions when working on this unit:

Store and transport all CMOS devices in conductive material so that all exposed leads are shorted together. Do not insert CMOS devices into conventional plastic snow trays used for storage and transportation of other semiconductor devices. Ground the working surface of the service bench to protect the CMOS device. We recommend using the Motorola Static Protection Assembly (part number 0180386A82), which includes a wrist strap, two ground cords, a table mat, and a floor mat. Wear a conductive wrist strap in series with a 100k resistor to ground. (Replacement wrist straps that connect to the bench top covering are Motorola part number RSX4015.) Do not wear nylon clothing while handling CMOS devices. Do not insert or remove CMOS devices with power applied. Check all power supplies used for testing CMOS devices to be certain that there are no voltage transients present. When straightening CMOS pins, provide ground straps for the apparatus used. When soldering, use a grounded soldering iron. If at all possible, handle CMOS devices by the package and not by the leads. Prior to touching the unit, touch an electrical ground to remove any static charge that you may have accumulated. The package and substrate may be electrically common. If so, the reaction of a discharge to the case would cause the same damage as touching the leads.

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8-3

8.4

Disassembling and Re-assembling the Radio General

Since these radios may be disassembled and re-assembled with the use of only four (board to casting) screws, it is important to pay particular attention to the snaps and tabs, and how parts align with each other. The following tools are required for disassembling the radio (see Chapter 3 for a list of service aids): knob remover/chassis opener penknife-size screwdriver TORX T6 screwdriver

If a unit requires more complete testing or service than is customarily performed at the basic level, send this unit to a Motorola Authorized Service Center. See Appendix B for a list of authorized service centers. The following disassembly procedures should be performed only if necessary: Chassis Disassembly Speaker Disassembly PTT Disassembly

8.4.1

Radio Disassembly Detailed

1. Turn off the radio 2. Remove the battery (Figure 8-1): a. b. c. Slide the battery latch into the unlock position. Disengage by pushing downward and holding the latch towards the front of the radio. With the battery latch disengaged, slide the battery down from the top of the radio about 1cm (1/2 in). Once the battery is free from the battery rails, lift it directly away from the radio. Remove the battery from the radio.

8.4.1.1 Front Cover From Chassis Disassembly

Lock

Unlock

Battery Latch

Figure 8-1. Battery Removal

8-4

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

3. Remove the antenna. 4. Pry off the volume and channel selector knobs from their shafts using the knob removal/chassis opener tool (Motorola part # 6686533Z01). (Figure 8-2)

Figure 8-2. Antenna and Knob Removal Note: Both knobs slide on and off. However the knobs are designed to fit very tightly on the shaft. 5. Separate the chassis from the front housing assembly by using the knob remover/chassis opener too. Place the broad side of the opener into the slots located at the base of the radio (Figure 8-3). Press the handle on the opener downwards. This pressing action forces the thin inner plastic wall toward the base of the radio, releasing the two chassis base tabs..

Knob Remover/ Chassis Opener

Radio Chassis

Figure 8-3. Chassis Removal

CAUTION: Marring the front cover O-ring sealing area will prevent the radio from sealing properly. If the O-ring is damaged, replace it with a new one.

Note: The speaker wire assembly microphone wire assembly and keypad ribbon connector connecting the front housing assembly and the chassis prevent the two units from being completely separated

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8-5

6. Pull the chassis assembly out of the front cover only until the volume and channel selectors shaft just clear the top of the case. (Figure 8-4). Rotate the chassis counterclockwise out of the housing and position next to the housing. Take care not to damage the speaker and microphone wires that are still connected to the chassis (Figure 8-4).

Speaker Connector

Shroud Microphone Connector

Figure 8-4. Microphone and Speaker Connections 7. Unplug the speaker wire assembly from the 2-pin connector on the chassis. 8. Unplug the microphone wire assembly from the socket on the chassis. 9. Move the chassis away from the housing and place on a clean work surface.

8.4.1.2 Dust Cover Disassembly

1. Gently pry the top of the dust cover away from the body of the radio. (See Figure 8-5). 2. Rotate the dust cover 90 in a counterclockwise direction to allow the key to be removed. 3. Separate the dust cover away from the body of the radio. The dust cover key is fragile; apply only light pressure to the key while removing the dust cover.

key

a. Pry dust cover from body.

b. Rotate dust cover 90 to allow key to be removed. Figure 8-5. Dust Cover Disassembly

c. Separate dust cover from body.

8-6

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8.4.1.3 Speaker and Microphone Disassembly

Note: The speaker is held in place with a retainer bracket. Be careful not to damage the speaker when removing the retainer bracket. 1. Remove the screw from the speaker retainer using a T6 Torx screwdriver (Figure 8-6). 2. Lift the retainer off the speaker, sliding end of retainer out of corner slot on the housing. 3. Lift the speaker out from the front housing. 4. Carefully lift microphone assembly out of housing.

Retainer Bracket

Speaker

Wire Connector

Radio Housing Microphone Assembly

Figure 8-6. Removal Speaker-Microphone Assembly

8.4.1.4 PTT Disassembly

1. If required, the PTT (Figure 8-7) can be disassembly using a small screwdriver, as follows: a. b. c. d. Insert the tip of a small screwdriver underneath the PTT and unsnap the top tab. Pry the PTT away from the radio housing. Inspect the two hooks. If bent or broken, the PTT must be replaced. Remove the PTT seal.

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8-7

Tab Hooks Flat Blade Screwdriver

PTT Seal

Tab

Figure 8-7. PTT Removal

8.4.2

Chassis Disassembly
CAUTION: Refer to the CMOS CAUTION paragraph (8.3) before removing the main board. Be sure to use Electrostatic Discharge protection when handling circuit boards.

1. Remove the O-ring. 2. Use a Torx screwdriver with a T6 bit to remove the four screws (Figure 8-8) holding the main board to the chassis.

Audio Jack Shroud

Main Board

Radio Chassis

O-Ring

Figure 8-8. Removal of Main Board from Chassis 3. The audio jack shroud can be removed from the main board. 4. Lift the main board from the chassis. 5. Remove the battery contact seal.

8-8

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8.4.3

Radio Re-assembly - Detailed

1. Insert the tail of the dust cap into the bottom hole of the audio jacks housing opening (Figure 8-9). 2. Press the dust cap until the tail is fully into the hole. 3. Twist the dust cap counter-clockwise until the cap is seated properly onto the recess. 4. Press the cap again to ensure it fully covers the opening for the audio jack.

8.4.3.1 Dust Cover Re-assembly

Figure 8-9. Dust Cap Re-assembly

8.4.3.2 Microphone and Speaker Re-assembly

1. Check that the speaker felt is in position and is not damaged. If damaged replace felt. 2. Insert the microphone sub-assembly into the microphone boot. 3. Insert the Boot and microphone sub-assembly into the microphone recess in the housing and route the wires as shown in Figure 8-10.
Microphone Boot Microphone Recess

Microphone Position

Figure 8-10. Microphone Re-assembly 4. Locate the speaker tab and align it with the tab opening in the front housing (Figure 8-11). 5. Insert the speaker tab into the speaker recess in the housing. Ensure the speaker is seated flush in the housing

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8-9

Note: Make sure the speaker and microphone wires are routed tightly between the speaker basket and the housing post 6. Insert one end of the speaker retainer into the slot in the front housing (See Figure 8-11).

Speaker Retainer

Speaker Tab Speaker Tab Opening Front Housing Slot

Figure 8-11. Speaker Re-assembly Note: When fastening the speaker retainer screw, make sure the wires are out of the way to prevent pinching by the retainer. 7. Install the retainer screw using a T6 Torx screwdriver. Torque to 0.26 - 0.28Nm (2.3 - 2.5 lb/in).

8.4.3.3 Chassis Assembly/Re-assembly

1. Replace the battery contact seal (if necessary) surrounding the battery contact (Figure 8-12). 2. Remove the old Interface Pad from the chassis by scraping off the pad and adhesive with a straight razor. Use rubbing alcohol and a cloth to completely remove the adhesive from the chassis surface. With the chassis clean and dry, add a new Interface Pad to the chassis. 3. Place the main circuit board straight down on top of the chassis with the frequency and volume switches facing down (Figure 8-15. Note: Be sure the battery contact seal protrudes through the chassis and is not pinched under the chassis. 4. Use the T6 Torx screwdriver to fasten the screws holding the main board to the chassis. Tighten to 0.42 - 0.44Nm (3.7 - 3.9 in/lb). 5. Replace the O-ring by positioning it in the top groove by the volume/frequency switches. Stretch the O-ring to place it into the retaining groove at the bottom end of the chassis. 6. Check that the O-ring is not twisted and is being held by the top and bottom chassis groves. 7. Replace the audio jack shroud.

8-10

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

Frequency & Volume Switches

Audio Jack Shroud (Replace after Plugging in Speaker and Mic)

Main Board Interface Pad

Radio Chassis Battery Contact Seal O-ring

Figure 8-12. Installation of Main Board onto Chassis

8.4.3.4 Chassis and Front Cover Re-assembly

1. Dress and connect the speaker wires. Note: Care should be taken when dressing the speaker and microphone wires to avoid pinching them between the speaker magnet and shield, or between the accessory connector and housing. Note: Ensure that the plug orientation is correct with the exposed pins in the wire casing facing upward and fully plugged in. a. Connect the speaker wire assembly into the 10-pin connector on the main board and bend the wires at the board connector so the wires are positioned toward the top of the radio (Figure 8-13). Connect the microphone wire assembly into the two hole socket on the main board and bend the wires at the board connector so the wires are positioned toward the top of the radio (Figure 8-13). Slide the audio jack shroud onto accessory connector (Figure 8-12).

b.

c.

2. Slide the volume potentiometer and frequency switch shafts into their respective holes in the front cover. Look through the accessory connector opening to make certain that the wires are not pinched. 3. Push the topside of the board chassis upward until it touches the housing end. Before snapping the board into the housing, perform the following checks.: a. b. c. Open the dust cap and ensure the wires are not pinched between the shroud and housing. Ensure the O-ring is seated in the groove. Ensure that the bottom side of the dust cap is fully pressed into the housing before the snapping the board into place.

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8-11

Speaker Connector

Microphone Connector Shroud

Figure 8-13. Microphone and Speaker Wires Re-assembly

Radio Chassis

Figure 8-14. Fastening the Chassis 4. Snap chassis assembly completely into the top of the front cover (Figure 8-14) until it settles in place. 5. Make sure the O-ring is properly seated. If the O-ring seal is pinched, separate the chassis from the housing using the knob removal/chassis opener and dress O-ring properly. 6. Snap the bottom of the chassis into the front cover. 7. Check that O-ring is visible at the corners. 8. Re-assemble the knobs, antenna, and battery.

8-12

Non-Keypad Model Disassembly and Re-assembly: Disassembling and Re-assembling the Radio General

8.4.3.5 PTT Re-assembly

1. Place the PTT seal over the ridge around the top hole. Press down to seat the seal around the ridge. 2. Place the bottom tab in the slot inside the front housing PTT opening. Slightly slide down the PTT and bow it by placing one finger under the middle of the PTT, so that the top tab can be aligned and inserted into the top slot (Figure 8-15a). 3. Press the PTT assembly against the front cover opening (Figure 8-15b).

a. Place bottom tab into bottom slot. Place top tab into top slot.

b. Push down on PTT toward bottom of radio so hooks do not get crushed.

Figure 8-15. PTT Re-assembly

Non-Keypad Model Disassembly and Re-assembly: Mechanical View and Parts List

8-13

8.5
8.5.1

Mechanical View and Parts List

CP140 Non-Keypad Exploded View and Parts List

2 27 3 26 25 24 23 9 10 11 12 13 14 15 28 22 21 20 16 17 4 5 6 7 8

19 18

Figure 8-16. CP140 Non-Keypad Radio Exploded View

8-14

Mechanical View and Parts List

Item
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Motorola Part Number

See Section 6 3680530Z02 1386440Z02 Not Field Repairable 1586391Z01 3586621Z01 3886489Z01 4586439Z01 5085738Z08 4286620Z01 3586621Z02 0780608V01 5085880L01 3286431Z02 7586436Z01 2786389Z01 3286435Z01 Ref. Chap 1 Model Charts 0304726J05 1586437Z01 5586445Z02 4105944K01 3886441Z01 3286432Z01 3386443Z01 6186446Z02 3680529Z01 0386434Z01

Description
Antenna Knob, Frequency Escutcheon, Top; 16 Ch. Antenna Adaptor / Seal Housing, ELP+, Plain Felt, Speaker PTT, Rubber PTT, Plastic Speaker Retainer, Speaker Felt, Microphone Boot, Microphone Microphone Seal, Main O-ring Pad, PA Interface Chassis Seal, Battery Contact Block Back Cover Kit (Main Board + chassis) Screws, Chassis; 4 Used Shroud, Audio Jack Latch Assembly Spring, Latch; 2 Used Cap, Dust Seal, Control Shaft Label, Escutcheon Seal Lightpipe Knob, Volume Screw, Speaker Retainer

NON-REFERENCED ITEMS 3386625Z01 3386623Z05 Nameplate, Motorola Nameplate, CP140

Chapter 9 Troubleshooting Tables

9.1

Power-Up Error Codes

During radio power-up, the radio performs dynamic tests to determine if the radio is working properly. Problems detected during these tests are presented as an error code on the radios display. The presence of an error code should prompt a user that a problem exists and that a service technician should be contacted. Use Table 9-1 to aid in understanding particular operational error codes. Table 9-1. Power-Up Error Code Display Error Code Possible Causes
RAM Test Failure

Corrective Action
Retest radio by turning if off and tuning it on again. If message reoccurs, replace main board or send radio to depot. Reprogram FLASH memory and retest. If message reoccurs, replace main board or send radio to depot. Reprogram codeplug with correct codeplug and retest. If message reoccurs, replace main board or send radio to depot.

RAM ERR

ROM ERR EPRM ERR

ROM checksum is wrong EEPROM Hardware Error Codeplug structure mismatch or non-existence of codeplug or, EEPROM Checksum Error Codeplug checksum is wrong

9.2

Operational Error Codes

During radio operation, the radio performs dynamic tests to determine if the radio is working properly. Problems detected during these tests are presented as an error code on the radios display. The presence of an error code should prompt a user that a problem exists and that a service technician should be contacted. Use Table 9-2 to aid in understanding particular operational error codes. Table 9-2. Operational Error Code Display Error Code Possible Causes
Synthesizer Out-of-Lock

Corrective Action
Verify codeplug and reprogram if necessary. If message reoccurs, replace main board or send radio to depot.

SYN UNLK

9-2

Troubleshooting Tables: Troubleshooting Table for Receiver

9.3

Troubleshooting Table for Receiver

Table 9-3 lists the possible causes of, and corrections for, receiver problems. Table 9-3. Receiver Troubleshooting Table Symptom Possible Causes
1. Dead Battery. 2. Blown Fuse 3. On/Off Switch 4. Regulators 5. Regulator fault

Corrective or Test (Measurements at Room Temperature)

Replace with charged battery. Send radio to depot.

Radio Dead; Display Does Not Turn On

Radio Dead; Display Turns On No Receive Audio, or Receiver Does Not Unmute

Transceiver Board Programming

Send radio to depot. 1. Does the transmitted signal match the receiver configuration (PL, DPL, etc.)? 2. With the monitor function enabled, can the radio be unmuted?

Audio Distorted or Not Loud Enough RF Sensitivity Poor

Synthesizer Not On Frequency 1. Synthesizer Not on Frequency 2. Antenna Switch/Connector 3. Receiver Front End Tuning

Check synthesizer frequency by measuring the transmitter frequency; realign it off by more than 150 Hz (VHF), 500 Hz (UHF) Check synthesizer frequency by measuring the transmitter frequency; realign it off by more than 150 Hz (VHF), 500 Hz (UHF) Send radio to depot. Check RF front-end tuning for optimum sensitivity using the tuner. Send radio to depot.

Radio Will Not Turn Off

Transceiver Board

Troubleshooting Tables: Troubleshooting Table for Transmitter

9-3

9.4

Troubleshooting Table for Transmitter

Table 9-4 lists the possible causes of, and corrections for, transmitter problems. Table 9-4. Transmitter Troubleshooting Table Symptom Possible Causes
1. Tx Power Level or Frequency 2. No Injection To Power Amplifier Antenna Switch/Connector

Corrective or Test (Measurements at Room Temperature)

Check Tx power level and frequency programming (from tuner). Send radio to depot.

No RF Power Out

No Modulation; Distortion Modulation

1. Programming 2. Transceiver Board

Check deviation and compensation settings using the tuner. Send radio to depot. Realign if necessary. Send radio to depot. Check programming. Send radio to depot. Send radio to depot.

Bad Microphone Sensitivity

1. Check Deviation and Compensation 2. Microphone

No/Low Signaling (PL, DPL, MDC) Cannot Set Deviation Balance

1. Programming 2. Transceiver Board RF Board

9-4

Troubleshooting Tables: Troubleshooting Table for Transmitter

Notes:

Appendix A

Accessories

Antennas
NAD6502_R HAD9742 HAD9743 NAE6522_R NAE6483_R 8505816K24 8505816K26 5886627Z01 VHF Heliflex Antenna 14cm (146-174 MHz) VHF Stubby Antenna, 9cm (146-162 MHz) VHF Stubby Antenna, 9cm (162-174 MHz) UHF Heliflex Stubby Antenna 9cm (438-470 MHz) Flexible Whip Antenna (403-520 MHz) UHF Heliflex Stubby (400-440 MHz) UHF Heliflex Stubby (470-520 MHz) Antenna Adapter

Carrying Accessories
RLN5383 RLN5384 RLN5385 RLN5498 RLN5496 RLN5497 RLN5640 RLN5641 RLN5642 HLN9701B HLN9985B HLN8255 NTN5243 RLN4815A RLN4570A Hard Leather Case with Belt Loop and D rings Hard Leather Case with 2-1/2 inch swivel Belt Loop Hard Leather Case with 3 inch swivel Belt Loop Hard Leather Case with Belt Loop Hard Leather Case, Full DTMF with 2-1/2 inch Swivel Belt Loop Hard Leather Case, Full DTMF with 3 inch Swivel Belt Loop Hard Leather Case, Full DTMF with Belt Loop Hard Leather Case, Full DTMF with 2-1/2 inch Swivel Belt Loop Hard Leather Case, Full DTMF with 3 inch Swivel Belt Loop Nylon Case with Belt Loop and D ring Waterproof Bag 3 inch Spring Action Belt Clip Shoulder Strap for Hard Leather Cases attaches to D-Shaped Rings on case) Universal RadioPak Break-away Chest Pack

Miscellaneous Accessoires
RLN5500 Accessory Retainer Kit

Chargers
WPLN4138_R WPLN4139_R WPLN4140_R WPLN4161 WPLN4162 WPLN4163 Desktop Rapid Charger w/US Plug Desktop Rapid Charger w/Euro Plug Desktop Rapid Charger w/UK Plug Multi-Unit Rapid Charger w/US Plug Multi-Unit Rapid Charger w/Euro Plug Multi-Unit Rapid Charger w/UK Plug

A-2

Accessories:

Batteries
NNTN4496_R NNTN4497_R NNTN4851_R NNTN4852_R NNTN4970_R NiCd, 1100 mAh Li-lon, High Cap, 1800 mAh NiMH, 1400 mAh NiMH FM, 1300 mAh Slim Li-Ion, 1600 mAh

Audio Accessories
HMN9752 HMN9727 RLN4894 HMN9754 RLN4895 RLN5198_P Earpiece with Volume Control, 1-Wire (plastic earloop) (Beige) Earpiece without Volume Control, 1-Wire (plastic earloop) (Beige) Earpiece without Volume Control, 1-Wire (plastic earloop) (Black) Earpiece with Microphone & PTT Combined, 2-Wire (Beige) Earpiece with Microphone & PTT Combined, 2-Wire (Black) Earpiece with Microphone & PTT Combined (Black) including Low Noise Kit, 2-Wire Surveillance Kit w/Clear Comfortable Acoustic Tube (includes NTN8371) Flexible Ear Receiver (RX only) Flexible Ear Receiver with Microphone & PTT Combined Earset w/Flexible Boom Microphone Earbud with Microphone & PTT Combined, 2-Wire (Black) Earbud with Microphone & PTT Combined Earbud with Microphone & PTT Combined Earbud Single Wire Receive Only (Black) Extreme Noise Kit Replacement Noise Attenuating Plug for NTN8370 Low Noise Kit Small Custom Clear Earpiece, Right Ear Small Custom Clear Earpiece, Left Ear Medium Custom Clear Earpiece, Right Ear Medium Custom Clear Earpiece, Left Ear Large Custom Clear Earpiece, Right Ear Large Custom Clear Earpiece, Left Ear 2-wire Comfort Earpiece with Microphone & PTT Combined, Beige 2-wire Comfort Earpiece with Microphone & PTT Combined, Black Standard 95 dB Ear Microphone with PTT Interface Module Standard 95 dB Ear Microphone with VOX & PTT Interface Module Ring PTT Switch for Ear Microphone System Body PTT Switch for Ear Microphone System

BDN6720 PLMN4443 PLMN4444 HMN9036 PMLN4294 PMLN4442 HLN9132 NTN8370 5080384T72 NTN8371 RLN4760 RLN4763 RLN4761 RLN4764 RLN4762 RLN4765 RLN5317 RLN5318 BDN6646 BDN6706 0180358B38 0180300E83

Accessories:

A-3

Headsets
RLN5411 PMMN4001 HMN9013 RMN4016 RLN5238 HMN9021 HMN9022 BDN6647 BDN6648 5080371E66 RMN5015 REX4648 RKN4090 RMN4051 RMN4052 RMN4053 RMN4054 RMN4055 HLN9133 RKN4094 PMLN4425 MDPMLN4445 Ultra-Lite Breeze Behind the Head Headset Ultra-Lite Earset with Mic and PTT Lightweight Headset w/o In-line PTT Lightweight Headset with In-line PTT Lightweight Headset with In-line PTT, NFL Style Medium Weight Over the Head Dual Muff Headset Medium Weight Behind the Head Dual Muff Headset Medium Weight Single Speaker Headset Heavy Duty Dual Muff Headset with Noise Canceling Microphone Replacement Ear Pad for BDN6647 Heavy Duty Dual Muff Racing Headset (requires RKN4090 Headset Adapter Cable) Ear Pad and Windscreen Kit Adapter Cable for use with RMN5015 Racing Headset 2-Way Hard Hat Mount, Black, Noise Reduction Rating (22db) (requires RKN4094 Adapter Cable) Tactical Headband Style Headset, Grey Tactical Hard Hat Mount Headset, Grey Receive-Only Hard Hat Mount Headset with 3.5mm Right Angle Plug Receive-Only Headband Style Headset with 3.5mm Right Angle Plug VOX Adapter Kit (for use with Headsets only) In-Line PTT Adapter for use with headsets RMN4051, RMN4052, and RMN4053 only) Earset Boom Microphone w/Remote Ring PTT Ultra-Light Headset with Boom Microphone

Remote Speaker Microphones

HMN9030 RLN4904 HKN9094 PMMN4008 Remote Speaker Microphone Mic Jacket for HMN9030 Remote Speaker Microphone Replacement Cord for HMN9030 Remote Speaker Microphone

A-4

Accessories:

Manuals
6866550D01_ GMLN1091A GMLN1092A GMLN1093A GMLN1094A GMLN1098A 6881096C29_ 6864117B25_ 6866550D20_ CP140/CP160/CP180 Basic User Guide - Multi-Language CP140/CP160/CP180 Basic User Guide - Multi-Language CDROM CP100 Series Product Manual - English CP100 Series Product Manual - French CP100 Series Product Manual - Russian CP100 Series Product Manual - English/French/Russian CDROM FM Listing Booklet Product Safety and RF Exposure Booklet CP100 Series Detailed Service Manual, English

Appendix B

Warranty, Service Support, and Replacement Parts

1.0

Scope of Manual
This manual is intended for use by service technicians familiar with similar types of equipment. It contains service information required for the equipment described and is current as of the printing date. Changes which occur after the printing date may be incorporated by a complete Manual revision or alternatively as additions.
NOTE Before operating or testing these units, please read the Safety Information Section in the

front of this manual.

2.0

Warranty and Service Support

Motorola offers long term support for its products. This support includes full exchange and/or repair of the product during the warranty period, and service/ repair or spare parts support out of warranty. Any "return for exchange" or "return for repair" by an authorised Motorola Dealer must be accompanied by a Warranty Claim Form. Warranty Claim Forms are obtained by contacting an Authorised Motorola Dealer.

2.1

Warranty Period and Return Instructions

The terms and conditions of warranty are defined fully in the Motorola Dealer or Distributor or Reseller contract. These conditions may change from time to time and the following notes are for guidance purposes only. In instances where the product is covered under a "return for replacement" or "return for repair" warranty, a check of the product should be performed prior to shipping the unit back to Motorola. This is to ensure that the product has been correctly programmed or has not been subjected to damage outside the terms of the warranty. Prior to shipping any radio back to the appropriate Motorola warranty depot, please contact Customer Resources (Please see page 2 and page 3 in this Chapter). All returns must be accompanied by a Warranty Claim Form, available from your Customer Services representative. Products should be shipped back in the original packaging, or correctly packaged to ensure no damage occurs in transit.

2.2

After Warranty Period

After the Warranty period, Motorola continues to support its products in two ways. 1. 2. Motorola's Radio Aftermarket and Accessory Division (AAD) offers a repair service to both end users and dealers at competitive prices. AAD supplies individual parts and modules that can be purchased by dealers who are technically capable of performing fault analysis and repair.

B-2

Warranty, Service Support, and Replacement Parts:

2.3

European Radio Support Centre (ERSC)

The ERSC Customer Information Desk is available through the following service numbers: Austria: Belgium: Denmark: Finland: France: Germany: Greece: UK : Ireland: 08 00 29 75 41 08 00 72 471 80 88 05 72 08 00 11 49 910 08 00 90 30 90 08 00 18 75 240 00 80 04 91 29 020 08 00 96 90 95 18 00 55 50 21 Italy: Luxemburg: Netherlands: Norway: Portugal: Spain: Sweden: Switzerland: Iceland: 80 08 77 387 08 00 23 27 08 00 22 45 13 80 01 11 15 08 00 84 95 70 90 09 84 902 02 07 94 307 08 00 55 30 82 80 08 147

Or dial the European Repair and Service Centre: Tel: +49 30 6686 1555 Please use these numbers for repair enquiries only.

2.4

Piece Parts
Some replacement parts, spare parts, and/or product information can be ordered directly. If a complete Motorola part number is assigned to the part, it is available from Motorola Radio Aftermarket and Accessory Division (AAD). If no part number is assigned, the part is not normally available from Motorola. If the part number is appended with an asterisk, the part is serviceable by Motorola Depot only. If a parts list is not included, this generally means that no user-serviceable parts are available for that kit or assembly. All part orders should be directed to : Motorola GmbH Customer Care Am Borsigturm 130 13507 Berlin Germany.

Warranty, Service Support, and Replacement Parts:

B-3

2.5

Technical Support
Motorola Product Services is available to assist the dealer/distributors in resolving any malfunctions which may be encountered. UK/Ireland - Richard Russell Telephone: +44 (0) 1256 488 082 Fax: +44 01256 488 080 Email: [email protected] Central/East Europe - Siggy Punzenberger Telephone: +49 (0) 6128 70 2342 Fax: +49 (0) 6128 95 1096 Email: [email protected] Scandinavia Telephone: +46 8 735 9282 Fax: +46 8 735 9280 Email: [email protected] Germany -Customer Connect Team Telephone: +49 (0) 30 6686 1539 Fax: +49 (0) 30 6686 1916 Email: [email protected] France - Lionel Lhermitte Telephone: +33 1 6929 5722 Fax: +33 1 6929 5904 Email: [email protected] Italy - Ugo Gentile Telephone: +39 0 2822 0325 Fax: +39 0 2822 0334 Email: [email protected] Africa & Middle East - Armand Roy Telephone: +33 1 6929 5715 Fax: +33 1 6929 5778 Email: [email protected]

B-4

Warranty, Service Support, and Replacement Parts:

Glossary of Terms

Term ALC

Definition Automatic Level Control: a circuit in the transmit RF path that controls RF power amplifier output, provides leveling over frequency and voltage, and protects against high VSWR (voltage standing wave ratio). Audio Signalling Filter Integrated Circuit Bad Key Chirp Compact Disk Compression Customer Programming Software Carrier Squelch Dual-Tone Multifrequency Digital Private-Line Electronically Erasable/Programmable Read-Only Memory: used by the radio to store its personality Software, or a software/hardware combination of computer programs and data, with a fixed logic configuration stores in a read-only memory. Information cannot be altered or reprogrammed. Frequency Generation Unit Gallium Arsenide: a type of crystalline material used in some semiconductors. Good Key Chirp Inbound Signalling Word: data transmitted on the control channel from a subscriber unit to the central control unit. Longhorn Data: a bidirectional 0-5V, RS-232 line protocol that uses the microcontrollers integrated RS-232 asynchronous serial communications interface (SCI) peripheral. Low Level Expander: slight amount of volume expansion; used to improve the signal to noise ratio. Micro Controller Unit Motorola Radio-Telephone Interconnect: a system that provides a repeater connection to the Public Switched Telephone Network (PSTN). The MRTI allows the radio to access the telephone network when the proper access code is received. Over-Molded Pad-Array Carrier: a Motorola custom package, distinguished by the presence of solder balls on the bottom pads. Printed Circuit Board Private-Line tone squelch: a continuous sub-audible tone that is transmitted along with the carrier.

ASFIC BKC CD CMP CPS CSQ DTMF DPL EEPROM Firmware

FGU GaAs GKC ISW LH DATA

LLE MCU MRTI

OMPAC PC Board PL

G-2

Term PLL PTT RAM Registers RESET RF PA RIB ROM RSSI RPT/TA Softpot Software SPI (clock and data lines) Squelch Standby Mode TOT TPL C UHF P VCO VCOBIC VHF VSWR

Definition Phase-Locked Loop: a circuit in which an oscillator is kept in phase with a reference, usually after passing through a frequency divider. Push-To-Talk: the switch located on the left side of the radio; when pressed, causes the radio to transmit. Random Access Memory: the radios RAM is loaded with a copy of the EEPROM data. Short-term data-storage circuits within the microcontroller. Reset line: an input to the microcontroller that restarts execution. Radio Frequency Power Amplifier Radio Interface Box Read Only Memory Received Signal-Strength Indicator: a dc voltage proportional to the received RF signal strength. Repeater/Talk-Around A computer-adjustable electronic attenuator Computer programs, procedures, rules, documentation, and data pertaining to the operation of a system. Serial Peripheral Interface: how the microcontroller communicates to modules and ICs through the CLOCK and DATA lines. Muting of audio circuits when received signal levels fall below a pre-determined value. An operating mode whereby the radio is muted but still continues to receive data Time-Out Timer: a timer that limits the length of a transmission. Tone Private-line Microcontroller Ultra High Frequency Microprocessor Voltage-Controlled Oscillator: an oscillator whereby the frequency of oscillation can be varied by changing a control voltage. Voltage-Controlled Oscillator Buffer Integrated Circuit Very High Frequency Voltage Standing Wave Ratio