Scribd
Upload
146 views

Piping Eng Test

This document contains a 100-mark question paper for a Dimensional Academy of Engineering Piping Engineering exam. It consists of 33 multiple choice and short answer questions covering topics like ASME piping codes, pipe dimensions, differences between pipes and tubes, pipe fittings, flanges, gaskets, valves, pumps, piping layout, and thermal expansion calculations. The exam is 3 hours long and tests the candidate's knowledge of key concepts and standards in process piping design and engineering.

Uploaded by

aasatti
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
146 views

Piping Eng Test

This document contains a 100-mark question paper for a Dimensional Academy of Engineering Piping Engineering exam. It consists of 33 multiple choice and short answer questions covering topics like ASME piping codes, pipe dimensions, differences between pipes and tubes, pipe fittings, flanges, gaskets, valves, pumps, piping layout, and thermal expansion calculations. The exam is 3 hours long and tests the candidate's knowledge of key concepts and standards in process piping design and engineering.

Uploaded by

aasatti
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

DIMENSIONAL ACADEMY OF ENGINEERING PIPING ENGINERRING

Time: 3 hours QUESTION PAPER I Total 100 Marks

1. What is the ASME code followed for design of piping systems in Process pipings (Refineries & Chemical Industries)? - 2 Marks i. B31.1 ii. B31.3 iii. B31.5 iv. B31.9 - 2 Marks

2. Write down the outside diameter of following pipe? i. 3 inch ii. 6 inch iii. 10 inch iv. 14 inch

3. What is the difference between Pipe and Tube? 4. Normally where do we use the following? i. Eccentric reducers ii. Concentric reducers

- 2 Marks - 2 Marks

5. What should be the radius of long radius elbow? 6. Concentric reducer is used in pump suction. (Yes / No). Explain. 7. What should be the radius of long radius elbow? 8. What is the ASTM code for the following? i. CS pipe ii. CS fittings iii. CS flanges

- 2 Marks - 4 Marks - 2 Marks - 2 Marks

9. What is the ANSI/ASME dimensional standard for steel flanges & fittings? i. B16.3 ii. B16.5 iii. B16.9 iv. B16.10

- 2 Marks

10. Which are the different types of Gaskets? 11. Why do we provide Drip Leg in Steam Line? 12. What is the normal upstream and downstream straight length of orifice flow meter? 13. How do you calculate the pipe spacing? 14. How do you calculate the width of Pipe rack? 15. How do you calculate the thermal expansion in a pipe? 16. What is the basic span of supports for 2/6/10/24 pipe. 17. What is the purpose of expansion bellows? 18. What are the Insulation materials used for piping systems. 19. Which American institute standard does piping engineer refer (Write any 4)? Page 1 of 2 Total

- 2 Marks - 4 Marks - 2 Marks - 4 Marks - 4 Marks - 2 Marks - 2 Marks - 2 Marks - 2 Marks - 2 Marks - 46 Marks

Page 1 of 2

DIMENSIONAL ACADEMY OF ENGINEERING PIPING ENGINERRING


Time: 3 hours QUESTION PAPER I Total 100 Marks - 2 Marks iv. Gas transmission

20. What is the different ASME 31 code for pressure piping? i. Power piping. ii. Fuel Gas Piping. & distribution piping system. iii. Refrigeration Piping

5. Which American standard is referred for selection of following piping element? i. Flanges v. Valves ii. Butt Welded fittings vi. Pipes. iii. Gasket iv. Socket & Threaded fittings - 10 Marks - 3 Marks - 3 Marks - 2 Marks - 2 Marks - 5 Marks - 2 Marks - 5 Marks

21. How can flanges be classified based on Pressure- temperature ratings? 22. How can flanges be classified based on facing? 23. How can flanges be classified based on face finish? 24. Which type of gasket is recommended for high temperature and high-pressure application? 25. How the pipe fittings are classified based on end connections? 26. What is the function of valves? 27. How the valves are classified based on their function?

28. What is Equipment layout design? & What are the essential data/ documents required for preparation of equipment layout? - 5 Marks 29. How much space is kept in between column of pipe rack? 30. How much Headroom clearance is required under the following type of crossing? i. Structures/ pipe lines inside operating area. iii. Above crest of road for crane movement. movement. v. Above crest of road between process units. 31. What are different types of pumps? 32. How many types of centrifugal pump are available based on the Suction and Discharge arrangement? 33. What sort of drawing/ layout is required for piping layout? Page 2 of 2 Total Page 1 & 2 of 2 Total - 100 Marks - 2 Marks - 2 Marks - 4 Marks - 54 Marks ii. From top of the Rail. iv. Above crest of road for Truck - 2 Marks - 5 Marks

Page 2 of 2

You might also like