Scribd
Upload
2K views9 pages

Duct Design Calculation Sheet: Note:-Take the Value of α & β from above table use in the calculation

This document contains calculations for the design of a duct including thickness, bending stress, shear stress, deflection, and stiffener requirements. Key inputs include a pressure of 768 mm H2O, duct width of 1000 mm and height of 3000 mm. Calculations determine the required thickness as 4 mm based on the pressure, dimensions and allowable stresses. Bending moment, stresses, and deflection are then calculated and found to be within acceptable limits. Stiffener requirements are also calculated and the provided section is found to have sufficient modulus of inertia.

Uploaded by

chagar_harsh
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
2K views9 pages

Duct Design Calculation Sheet: Note:-Take the Value of α & β from above table use in the calculation

This document contains calculations for the design of a duct including thickness, bending stress, shear stress, deflection, and stiffener requirements. Key inputs include a pressure of 768 mm H2O, duct width of 1000 mm and height of 3000 mm. Calculations determine the required thickness as 4 mm based on the pressure, dimensions and allowable stresses. Bending moment, stresses, and deflection are then calculated and found to be within acceptable limits. Stiffener requirements are also calculated and the provided section is found to have sufficient modulus of inertia.

Uploaded by

chagar_harsh
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 9

DUCT DESIGN CALCULATION SHEET

Prepared by Sumit Malhotra

S.No
1
2
3
4
5
6
7

8
9
10
11
12
13
14
15
16
17
18
19
20

INPUT DATA
Parameters
Value
Pressure ( P )
768
Width ( W )
1000
Height ( H )
3000
Consider unsupported length of 'X' mm
1500
Allowable bending stress(Fb)
112

Units
mm H2O 0.007534
mm
mm
mm
2
N/mm

Remarks
N/mm2

Allowable Shear stress()


67
N/mm
4
Modulus Of Elasticity ( E )
170000
N/mm
CALCULATION FOR THICKNESS OF DUCT
X/H
0.25
0.28
0.33
0.4
0.5
0.66
1

0.00027 0.00046 0.00083


0.0016
0.0035
0.0083
0.022

0.024
0.031
0.041
0.056
0.08
0.116
0.16
X/H
1.4
1.6
1.8
2
2.5
3
3.5

0.043
0.05
0.06
0.066
0.07
0.078
0.086

0.26
0.28
0.3
0.34
0.4
0.43
0.46
Note :- Take the Value of & from above table use in the calculation
X/H Ratio
0.50
Enter Value of
1
Take mean value
Enter Value of
1
Required Thickness( tr )
2
=SQRT{(XPXH^2)/a}
mm
Actual Thickness Applied
4
mm
Maximum Bending Moment
2
=(P x X )/8
2119
Nmm
M.O.I of plate section ( I )
Distance from N.A( y )
Induced bending Stress( fb)

8000
2
1

mm4
N/mm2

Deflection Check()
=(5 x P x X4)/(384xExI)
0.37
mm
2
N/mm
Induced Axial Stress( fa )
1.6742E-09
Reaction R1 or Shear force
6.0
N
2
N/mm
Maximum Shear Stress ( max )
0.0005
CHECKING FOR INTERACTION RATIO

fa/Fa + fb/Fb< or = 1

4.17

SAFE

0.00893

SAFE

21
STIFFENER CALCULATION
22
23

Required M.O.I
4
=(5x Px X x 360)/(384 x E x X )
Actual M.O.I of ISA 65 X 65X 6

mm4
702
5.2

cm

0.0702

cm4

SAFE

OTHER FORMULA FOR DEFLECTION


4
4
=( x P x H )/E x ta )

3505.63

WHICH IS NOT SATISFACTORY

OTHER FORMULA FOR DEFLECTION


4
4
=( x P x H )/E x ta )

3505.63

WHICH IS NOT SATISFACTORY

N SHEET

Remarks
N/mm2

1.2
0.033
0.2
4
0.091
0.5

0.028
0.75

up to
infinity

Section AA from above Fig.

X/H

0.25
0.00027
0.024

calculation
Take mean value

2
5

SAFE

SAFE
cm4

SAFE

IS NOT SATISFACTORY

IS NOT SATISFACTORY

0.28
0.00046
0.031

0.4

0.33
0.00083
0.041

0.4
0.0016
0.056

0.5
0.0035
0.08

0.66
0.0083
0.116

1
0.022
0.16

1.2
0.033
0.2

1.4
0.043
0.26

1.6
0.05
0.28

1.8
0.06
0.3

2
0.066
0.34

2.5
0.07
0.4

3
0.078
0.43

3.5
0.086
0.46

4
0.091
0.5

Longitudinal Deflection Calculation


Prepared by Sumit Malhotra

S.No
1
2
3
4
5
6
7
8
9
10
11
12

INPUT DATA
Parameters
Value
Inside Pressure ( P )
768
Width ( W )
1000
Height ( H )
3000
Span Length ( L ) Column to Column
3000
Plate Thickness
4
Allowable bending stress(Fb)
165
Allowable Shear stress()
67
Modulus Of Elasticity ( E )
170000
CALCULATION
Dead Load
7392.816
Total Dead + Live Load ( W )
8132.11
Maximum Bending Moment
=(W x L)/4
Required Section Modulus
( Ix ) Available M.O.I

Units
mm H2O
mm
mm
mm
mm
N/mm2
2

N/mm
4
N/mm
N
N

6099079.416
36964.11767

Nmm
mm3

35952042667

mm4

14

=(BD3/12 - bd3/12)
Maximum Deflection
4
=(5 x W x L )/(384 x E x Ix )

1.403

mm

15

Actual Section Modulus

23968028.44

13

Remarks
0.007534

10 % extra

9.231

SAFE

on Calculation

Malhotra

Remarks
0.007534

10 % extra

SAFE
SAFE

You might also like