1. The N1 Manual Set knob b) When pulled out disables the FMC input signal to the N1 indicator. 2.

The engine oil pressure is c) Unregulated and is primarily a function of engine N2 speed. 3. During an engine shutdown, the start switch holding solenoid is held in the cutout position until b) The engine speed falls below 30% N2 RPM. 4. The N1 RPM indicator indicates: a) The fan speed in percent of RPM and is used as the primary thrust setting reference. 5. Illuminating of the Red warning light above an EGT gauge indicates a) The EGT for the associated engine displayed has been reached or exceeded. 6. The N2 RPM indicator displays: a) High pressure compressor speed in percent of RPM 7. The START VALVE OPEN amber light indicates b) The engine starter valve is open and air is being supplied to the air driven starter. 8. The minimum engine oil pressure is c) 13psi 9. Illumination of the OIL FILTER BYPASS light a) Indicates an impending bypass of the oil Scavenge Filter. 10. The engine Ignition System contains c) Two high energy AC systems. 11. Placing the Engine Start Switch in the GRD position a) Opens the starter valve, closes the engine bleed air valve and the selected igniter(s) are energized when the Engine Start Lever is placed to IDLE. 12. Placing the Engine Start Switch to the CONT position provides high energy ignition to: a) The selected igniter(s) when the Engine Start Lever is in the IDLE position. 13. Placing the Engine Start switch to the FLT position c) Opens the starter valve and provides high energy ignition to both igniters when the Engine Start Lever is positioned to IDLE. 14. With the Ignition Select switch in the IGN R position c) The right igniter is selected for use on both engines.

15. The Engine Start Lever selected to IDLE during an engine start b) Energizes the ignition system, electrically opens the engine fuel shutoff valve in the wing leading edge, and mechanically opens the MEC shutoff valve. 16. Reverse thrust can be selected with the forward thrust levers in what position? B) Idle thrust position 17. Each engine has two igniter plugs. The start lever arms the igniter plug(s) selected by the ignition select switch. The Left igniter plug receives power from the AC TRANSFER BUS while the Right igniter plug receives power from the ACSTANDBY BUS. a) True 18. Starter Cutout speed is: c) 46% 19. Which hydraulic system normally powers the thrust reversers? b) System A for engine No.1 & system B for Engine No.2 20. What are the indications that the engine starter has disengaged? d) The start switch automatically returns to OFF, and the START VALVE OPEN light extinguishes 21. The thrust reverser may be deployed: a) When the fire switch is in DOWN position. b) When either radio altimeter is sensing less than 10 feet altitude c) When the air/ground safety sensor is in the ground mode d) All of the above 22. The Variable Bypass Valve (VBV) system controls and regulates LPC exit airflow prior to entry to HPC by means of .bleed valves, and uses fuel pressure to operate . hydraulic actuator that controls the opening and closing of these: A) Twelve - One. 23. When N2 reach ., the selector GROUND return in automatic to the position OFF. C) 46%. 24. The start lever is raised to IDLE when N2 is: A) 25%. B) 55%. C) 46%. 25. Generates N2 speed signals: B) Control Alternator. 26. There are ignition exciters for each engine C) Two. 27. Compressor Airflow Control prevents engine surges by using: C) VSV and VBV.

28. In Idle thrust the VBV is and the VSV is . C) Open - Closed. 29. In Takeoff power the VBV is and the VSV is . C) Closed - Open. 30. The VBV System is composed by .bleed valves C) 12. 31. The bleed air to High Pressure Turbine Clearance Control System (HPTCC) is provided: C) 5TH and 9th 32. The Oil Filter Differential Pressure Switch reacts to the pressure drop across the: B) Scavenge Oil Filter. 33. The Ground Air Source for Engine Starting is available through the ground service pneumatic connections. The normal required pressure is: B) 30 PSI. 34. During engine starting the selector GROUND is selected, the start valve, the light START VALVE OPEN and the Engine bleed valve A) Open - illuminates - Close. 35. When there is a stall on compressor, what happen with the stator vanes of VSV system? A) Close to decrease angle of attack. 36. When selects 2 on the Engine Ignition and Start Control Module: A) Only working the igniter plug 2. 37. The Pneumatic Starter Valve controls the airflow to the pneumatic starter, it is.. controlled operated butterfly valve: A) Electrically - pneumatically. 38. The EGT indication system is composed by ..Thermocouples and are connected in .. C) 09 - Parallel. 39. The thermocouples used in the CFM56-3 are made by junction of dissimilar metals: b) Nickel-chromium (Chromel) and Nickel-aluminum (Alumel). 40. On Test Vibration Survey, when we find an engine above 3.0 units read at the vibration indicator: b) Replace engine related to the test.