PETROSYNC

Synchronize Your Petroleum Skills

Reserve early disappointment! Reserve early to to avoid avoid disappointment!

API 510

Be the qualified API510 Inspector in 2014!

5 5 Days Days preparation preparation course course for for certification certification
Sculpt Your Skills for the Inspection, Repair, Alteration, and Rerating of Pressure Vessel Systems!

19th - 23rd May 2014 | Kuala Lumpur, Malaysia 01st - 05th September 2014 | Bandung, Indonesia

ATTEND THIS INTENSIVE COURSE TO MASTER:

INSTRUCTOR

Uday B. Kale (M. Eng. Mechanical)

Technical Director KUB Quality Services

SUMMARY OF PROFESSIONAL ACHIEVEMENT

API 510 & 570 Authorized Inspector AWS Certified Welding Inspector CSWIP 3.1 Authorized Welding Inspector ACCP Professional Level III (ASNT) ASNT NDT Level III BS EN 473 Level III API 580 Risk Based Inspection Supplementary Certification

Detailed explanations of all the information covered in the API 510 'Body of Knowledge' including ASME welding requirements for pressure vessels section IX and VIII ASME non-destructive testing principles and application of Section V Pressure vessel design review ASME Section VIII, weld sizes, vessel nozzle reinforcement, brittle fracture, weld efficiency factors, post weld heat treatment Pressure relieving devices, valves, bursting discs, setting, testing and inspection; API 510 inspection, repair and rerating of vessels, inspection intervals, inspection requirements, relationships to ASME codes. Corrosion, minimum thickness determination and remaining life calculations Inspection and degradation mechanisms of pressure vessels, corrosion and cracking mechanisms Erosion, common corrodents, hydrogen and H2S damage, alloy degradation.

PARTIAL CLIENT LIST

The Middle East: Qatar Petroleum, QAFAC, ADCO, ADGAS, ADMA, GASCO, Banagas, Technip (Bahrain), Equate Petrochemicals Company, Al Jubail Fertilizer Company, TUV Akadamie Middle East (UAE, Saudi Arabia and Qatar) Africa: BP - GUPCO (Egypt), Inspection and Test Nigeria Ltd India & Asia: Oil India Limited, Tata, Dacon Inspection Ltd Europe: Rosen Europe (The Netherlands)
Limited Attendees The course has limited seats to ensure maximum learning and experience for all delegates. Certificate of Attendance You will receive a Certificate of Attendance bearing the signatures of the Trainer upon successful completion of the course. This certificate is proof of your continuing professional development. Interactive Training You will be attending training designed to share both the latest knowledge and practical experience through interactive sessions. This will provide you with a deeper and more long-term understanding of your current issues. High Quality Course Materials Printed course manual will provide you with working materials throughout the course and will be an invaluable source of reference for you and your colleagues afterward. You can follow course progress on your laptop with soft copies provided.

SUPPORTED BY

PROGRAM OVERVIEW
To improve management control of process unit inspection, repair, alteration and rerating; and to reduce the potential for inspection delays resulting from regulatory requirements. -- API.org on API 570 Certification

WHY YOU SHOULD ATTEND

To ensure that all objectives of the course matches yours, all PetroSync programs are developed after intensive and extensive research within the industry PetroSync programs focus on your immediate working issues to ensure that you are able to apply and deliver immediate results in real work situations Application and implementation of industry knowledge and experience are the drivers for our course design, not theoretical academic lectures PetroSync training focuses on practical interactive learning tools and techniques including case studies, group discussions, scenarios, simulations, practical exercises and knowledge assessments during the course. Invest a small amount of your time to prepare before attending the course to ensure maximum learning PetroSync follows a rigorous selection process to ensure that all expert trainers have first-hand, up-to-date and practical knowledge and are leaders of their respective industrial discipline

American Petroleum Institute

(API) Code 510 Inspection, Repair, Alteration, and Rerating of Pressure Vessel Systems is recognized and used with confidence worldwide. The Piping Inspector Certification Program (PICP) is developed for the continual high level of efficiency and safety through emphasizing professional credibility and process integrity. Pressure Vessel system is one of the critical production assets in process industry. Organizations recognize the need to maintain authorized inspection agency and technically assess qualified pressure vessel engineers and inspectors to ensure facilities are at top performance. Therefore, API 510 certification is one of the most sought after professional competency that enables inspectors to be actively involved in the improvement of industry & environmental health and safety performance, reinforcement management control, compliance of inspection capabilities. With Mr. Uday Kales extensive involvements in the facilities inspection, as well as his practical coaching and mentoring approaches, this course not only prepare the candidates to pass API 510 examination with confident, it will also advance the appreciation of pressure vessel facilities and thus to broaden the technical knowledge base in order to avoid unplanned shutdown and reduce expenses!

IN-HOUSE SOLUTIONS
SAVE COST IMPROVE PERFORMANCE REDUCE RISK
PetroSync understands that in current economic climate, getting an excellent return on your training investment is critical for all our clients. This excellent training can be conducted exclusively for your organization. The training can be tailored to meet your specific needs at your preferred location and time. We will meet you anywhere around the globe. If you like to know more about this excellent program, please contact on +65 6415 4500 or email [email protected]

PROGRAM SCHEDULE

AUDIENCE
This course will specifically benefit Engineers, Supervisors, and Managers from the following disciplines: - Mechanical Engineering - Inspection - Maintenance & Operations - Technical & Engineering - QAQC and technical personnel with 2-3 years of experience in the management and planning of inspection and maintenance activities of pressure vessel system at upstream oil & gas facilities, refineries, process plants and petrochemical facilities.

08:00 Registration (Day1) 08:10 11:00 Session I 11:00 11:15 Refreshment & Networking 11:15 13:00 Session II 13:00 14:00 Networking Buffet Lunch 14:00 15:30 Session III 15:30 15:45 Refreshment & Networking 15:45 18:00 Session IV 18:00 End of Day

AGENDA OULTINE
MODULE - 2

DAY-1
MODULE 1
Welcome and Introduction Overview of API 510 Course

WELD SIZE FOR ATTACHMENT WELDS AT OPENINGS a) Conversion of a fillet weld throat dimension to leg dimension , conversion factor(0.707) b) Determine the required size of welds at openings (UW-16).

MODULE 3
NOZZLE REINFORCEMENT Key concepts of reinforcement, such as replacement of strength and limits of reinforcement. Credit for extra metal in shell and nozzle Calculate the required areas for reinforcement

MODULE 2
JOINT EFFICIENCIES a. Weld Joint Categories from UW-3; b. Type of radiography (full, spot, or none , RT-1, RT-2, etc.); c. Joint efficiency by reading Table UW-12; d. Joint efficiency for seamless heads and vessels Sections per UW-12 (d); and e. Joint efficiency for welded pipe and tubing per UW-12 (e).

MODULE - 4
1 SCOPE OF API 510 1.1 General Application 1.2 Specific Applications 1.3 Recognized Technical Concepts 2 references

MODULE - 3
THICKNESS CALCULATIONS a) The required thickness of a cylindrical shell (UG-27(c)(1)); b) The vessel part MAWP for a cylindrical shell c) The required thickness of a head-Hemispherical, Ellipsoidal, Torispherical d) The vessel part MAWP for a head

MODULE - 5
3 definitions 4 owner/user inspection organization p g 4.1 General 4.2 Owner/user Organization Responsibilities Resp

MODULE - 4
STATIC HEAD a) Calculate static head pressure on any vessel part; b) Calculate total pressure (MAWP + static head) on any vessel part; c) Calculate maximum vessel MAWP given vessel parts MAWP and elevations

DAY-3
MODULE - 1
5 inspection, examination and pressure testing practices 5.1 Inspection Plans 5.2 Risk-based Inspection 5.3 Preparation For Inspection 5.4 Inspection For Types Of Damage Modes Of Deterioration And Failure

MODULE -5
EXTERNAL PRESSURE a) Calculate the maximum allowable external pressure; b) Calculate whether a cylindrical shell meets Code design for external pressure. IMPACT TESTING a) Determine the minimum metal me temperature of a material which is exempt from impact i testing (UG-20 (f), UCS-66,UCS-68(c).)

MODULE 2
5.5 General Types Of Inspection And Surveillance 5.6 Condition Monitoring Locations 5.7 Condition Monitoring Methods

DAY-2
MODULE - 1
PRESSURE TESTING a) Calculate a test pressure compensating for temperature. (UG-99 & UG-100) b) The precautions associated with hydrostatic and pneumatic testing, c) Steps in a hydrotest Procedure (UG 99 and UG 100) d) All steps in a pneumatic test procedure (UG 100 and UG 102)

MODULE - 3
5.8 Pressure Testing 5.9 Material Verification And Traceability 5.10 Inspection Of In-service Welds And Joints 5.11 Inspection Of Flanged Joints

MODULE - 4
6 interval/frequency and extent of inspection 6.1 General

6.2 Inspection During Installation And Service Changes 6.3 Risk-based Inspection 6.4 External Inspection 6.5 Internal And On-stream Inspection 6.6 Pressure-relieving Devices

DAY-5

MODULE - 1
API RP 576, Inspection of Pressure-Relieving Devices 1. Relief Devices a) Description of Types -- (API RP-576, Section 2) b) Causes of Improper Performance (API RP-576, Section 4) c) Reasons for Inspection and Frequency Determination (API RP 576, Sections 3 & 5) d) Inspection and Test Service Procedures (API RP-576, Sections 6 and 7)

MODULE - 5
7 inspection data evaluation, analysis, and recording 7.1 Corrosion Rate Determination 7.2 Remaining Life Calculations 7.3 Maximum Allowable Working Pressure Determination

MODULE - 6
7.4 Fitness For Service Analysis Of Corroded Regions 7.5 API RP 579 Fitness For Service Evaluations 7.6 Required Thickness Determination 7.7 Evaluation Of Existing Equipment With Minimal Documentation 7.8 Reports And Records

MODULE - 2
A. Article 1, General Requirements: B. Article 2, Radiographic Examination

MODULE - 3
C. Article 6, Liquid Penetrant Examination, D. Article 7, Magnetic Particle Examination (Yoke and Prod techniques only): E. Article 23, Ultrasonic Standards, Section SE797

DAY-4

MODULE - 4
API RP 576, Inspection of Pressure-Relieving Devices

MODULE - 1
8 repairs, alterations, and rerating of pressure vessels . 8.1 Repairs And Alterations Authorization Approval Materials Requirements Welding Requirements

1. Relief Devices a) Description of Types -- (API RP-576, Section 2) b) Causes of Improper Performance (API RP-576, Section 4) c) Reasons for Inspection and Frequency Determination (API RP 576, Sections 3 & 5) d) Inspection and Test Service Procedures (API RP-576, Sections 6 and 7)

MODULE - 2
Heat Treating Requirements Preheating Post weld Heat Treating Local Postweld Heat treatment Repairs to Stainless Steel Weld Overlay and Cladding Rerating

MODULE - 5 ( 1 hour + 1 hour discussion )

Practice Examination-Open Book Practice Examination-Closed Book Feed Back and Closing

MODULE - 3
Introduction to ASME Sec. IX Welding Procedure tests Performance qualification tests Acceptance criteria Welding positions P-No, F-No and A-No. Review of: a. Welding Procedure Specification (WPS); and b. Procedure Qualification Record (PQR) And determine: a) Whether number and type of mechanical test listed on PQR are appropriate b) Whether the results of the tests are acceptable c) Whether all required essential and non-essential variables have been properly addressed.

API 510 5 Days Preparation Course for Certification

19th - 23rd May 2014 | Kuala Lumpur, Malaysia 01st - 05th September 2014 | Bandung, Indonesia

INSTRUCTOR

Uday B. Kale (M. Eng. Mechanical)

Technical Director KUB Quality Services

SUMMARY OF PROFESSIONAL ACHIEVEMENT

API 510 & 570 Authorized Piping Inspector AWS Certified Welding Inspector CSWIP 3.1 Authorized Welding Inspector ACCP Professional Level III (ASNT) ASNT NDT Level III BS EN 473 Level III API 580 Risk Based Inspection Supplementary Certification API 510 Authorized Pressure Vessel Inspector API 580 Risk Based Inspection Supplementary Certification API 653 Authorized Aboveground Storage Tank Inspector

01st - 05th September 2014 | Bandung, Indonesia

Qatar Petroleum BP - GUPCO (Egypt) Oil India Limited ADCO (Abu Dhabi) ADGAS (Abu Dhabi) ADMA (Abu Dhabi) GASCO (Abu Dhabi) QAFAC

PARTIAL CLIENT /PROJECT LIST

Rosen Europe (The Netherlands) Banagas (Bahrain) TATA (India) Al Jubail Fertilizer Company Technip (Bahrain) Equate Petrochemicals (Kuwait) TUV Akadamie Middle East (UAE, Saudi Arabia and Qatar) Inspection and Test Nigeria Ltd Dacon Inspection Ltd HBJ pipeline up-gradation projects

Uday B. Kale is an API570 authorized piping inspector. Currently

he is the technical director of M/s KUB Quality Services. He has involved in inspection, welding and NDT projects in the Middle East, Africa and India for over 15 years on offshore production platform and petrochemical refineries. Mr. Uday is very well-versed in international Codes and Standards. He performed and led the shutdown teams in performing NDE, internal and external inspection of equipments in central processing plant, ammonia plant, FCCU, SRU, SWS and amine treating units for Code stamp facilities of ADCO, Qatar Petroleum, Oil India, QAFAC, Banagas, Al Jubail Fertilizer Company. He was the appointed plant inspector for BP (GUPCO) in asset integrity management, who took charge of 9 offshore production complex, 75 Satellites and Onshore process units involving Close Visual Inspection of piping, equipments, NDT co-ordination, Baseline and Corrosion Monitoring. Furthermore, as an Inspector in GASCO OAG pipeline project, he conducted and witnessed Ultrasonic Examination of first 50 production weld joints of pipeline done by PWT (Pipe Welding Technology, GMAW).

With his extensive involvement in various projects, Mr. Uday is also an enthusiastic and knowledgeable mentor, who has been a faculty in training, examination, qualification and certification of API 510 & 570, ASME B31.3, API653, welding and NDT in the Middle East, Africa and Asia. He is a charted engineer with a Masters in Mechanical Engineering.

INVESTMENT PACKAGES
Please checklist the package that you are attending!
API 510 Pressure Vessel Package 19th - 23rd May 2014 Kuala Lumpur, Malaysia 01st - 05th September 2014 Bandung, Indonesia Early Bird Standard Price

PROGRAMME CONSULTANT
Contact Email Phone Fax : Cay Aagen : [email protected] : +65 6415 4500 : +65 6826 4322

Group Discount
3 or more at 10% disc from Standard Price and the same organization at the same time

SGD $ 2,795 SGD $ 2,795

SGD $ 2,995 SGD $ 2,995

TERMS AND CONDITIONS

DISCLAIMER
Please note that trainers and topics were confirmed at the time of publishing; however, PetroSync may necessitate substitutions, alterations or cancellations of the trainers or topics. As such, PetroSync reserves the right to change or cancel any part of its published programme due to unforeseen circumstances. Any substitutions or alterations will be updated on our web page as soon as possible.

* To enjoy the offer, full payment must be made before the deadline. * For 5 or more delegates, please inquire for more attractive package. * Prices include lunches, refreshments and training materials. Discounts cannot be combined with other promotional offers. * Important: Please note that registration without payment will incur a SGD 200 administration fee.

DELEGATE DETAILS
1st Delegate Name

Mr Email: Department:

Mrs

Ms

Dr

Others

Direct Line Number: Job Title: Head of Department:

2nd Delegate Name

DATA PROTECTION
The information you provide will be safeguarded by PetroSync that may be used to keep you informed of relevant products and services. As an international group we

Mr Email: Department:

Mrs

Ms

Dr

Others

may transfer your data on a global basis for the purpose indicated above. If you do not want us to share your information with other reputable companies, please tick this box.

Direct Line Number: Job Title: Head of Department:

3rd Delegate Name

Mr Email: Department:

Mrs

Ms

Dr

Others

Direct Line Number: Job Title: Head of Department:

CANCELLATION POLICY
You may substitute delegates at any time as long as reasonable advance notice is given to PetroSync. For any cancellation received in writing not less than fourteen (14)

INVOICE DETAILS
Attention Invoice to: ______________________________________________________________________________ Direct Line Number: ______________________________ Fax: _____________________________________________ Company:____________________________________________ Industry : __________________________________ Address: _______________________________________________________Postcode: _________________________ Country: ________________________Email: __________________________________________________________
Please note: - Indicate if you have already registered by Phone Fax Email Web - If you have not received an acknowledgement before the training, please call us to confirm your booking.

working days prior to the training course, you will receive a credit voucher worth total transaction with less a SGD 200 administration fee and any related bank or credit card charges. Delegates who cancel less than fourteen (14) working days of the training course, or who do not attend the course, are liable to pay the full course fee and no refunds will be granted.

PAYMENT METHODS
By Credit Card : Please debit my credit card: Card Number: Visa MasterCard AMEX Security Code: Expiry Date:

CERTIFICATE OF ATTENDANCE
70% attendance is required for PetroSync's Certificate of Attendance.

Name printed on card: _____________________________________________________________________ By Direct Transfer : Please quote invoice number(s) on remittance advice PetroSync LLP Bank details: Account Name: PetroSync LLP Bank Number: 7144 Branch Code: 013 Account No: 13-1-005531-6 Name of Correspondent Bank : Standard Chartered Bank, 6 Battery Road, Singapore 049909 SWIFT Code of Correspondent Bank: SCBLSGSGXXX All bank charges to be borne by payer. Please ensure that PetroSync LLP receives the full invoiced amount.

VENUE
All of our training courses are held in 4-5 star venues. The training venues are carefully selected by their location, training and their refreshment facilities. You will only learn in comfortable and convenient environments. Hotel accommodation and travel cost are not included in the registration fees. A special event hotel room rate will be arranged with the hotel and a hotel room reservation form will be provided upon confirmation of your attendance.

Conrmaon
I agree to PetroSyncs payment terms and cancellation policy.

CHARGES & FEE(s)

- For Payment by Direct TelegraphicTransfer, client has to bear both local and oversea bank charges. - For credit card payment, there is additional 4% credit card processsing fee.

Signature :
PAYMENT TERMS

____________________________________________________________________________
: Payment is due in full at the time of registration. Full payment is mandatory for event attendance.

Incorrect Details Please accept our apologies for mail or email that is incorrectly addressed. Please email us at [email protected] and inform us of any incorrect details. We will amend them accordingly.

To Register