Scribd
Upload
67 views7 pages

YUFRIDIN1

The document discusses FET amplifier configurations including common-source, common-drain, and common-gate. It explains how transconductance relates input to output current and drain resistance affects gain. Gain formulas and circuit analyses are provided for each configuration.

Uploaded by

athome
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
67 views7 pages

YUFRIDIN1

The document discusses FET amplifier configurations including common-source, common-drain, and common-gate. It explains how transconductance relates input to output current and drain resistance affects gain. Gain formulas and circuit analyses are provided for each configuration.

Uploaded by

athome
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

Objectives

Explain the operation and amplification properties of FET amplifiers Explain and analyze the operation of common-source, common-drain, and common-gate amplifiers Troubleshoot FET amplifiers

Chapter 8 FET Amplifiers

Introduction
FET amplifiers are similar to BJT amplifiers in operation.The purpose of the amplifier is the same for both FET amplifiers and BJT amplifiers. FET amplifiers have certain advantages over BJT amplifiers such as high input impedance. However, the BJT normally has a higher voltage gain. There are also similarities in the three amplifier configurations of FETs and BJTs. Common-source (emitter), common-drain (collector), and common-gate (base) are the three FET amplifier configurations.

FET Amplification
Lets first look at an equivalent FET circuit to better understand its operation. The FET is basically a current source that is controlled by VGS. Note that the resistance from gate to source can be neglected since it is so large in value and in most cases the drain to source resistance (rds) can be neglected as well.
Id = gmVgs (gm is the symbol
for transconductance)

FET Amplification
Voltage gain (Av) for any amplifier can certainly be determined by the formula AV = Vout/Vin or in the case of an FET amplifier, AV = Vds/Vgs. AV can also be determined by way of the transconductance and the drain resistor.

FET Amplification
The rds can lower the gain if it is not sufficiently greater than RD. Note that the two resistances are in parallel.

AV = gm(RDrds/(RD + rds) )

AV = gmRD

FET Amplification
RS can affect the gain as well. The gain is lowered with higher values of Rs and decreases with higher values of Rs. The formula below shows the relationship. Av = gmRD/(1+gmRS) PROVE THIS!

Common-Source Amplifiers
The common-source amplifier is biased such that the input stays within the linear range of operation.

out

VRs

Self biased common source amplifier. Note the source is at ac ground by way of C2..

Common-Source Amplifiers
The transfer characteristic curve and drain curves with load line give us a graphical representation of how the input signal affects the drain current with relation to the Q-point.

Common-Source Amplifiers
DC analysis of a common-source amplifier requires us to determine ID. Biasing at midpoint is most common so ID will be half of IDSS. Note that the capacitors are viewed as open components when only dc is considered.

Common-Source Amplifiers
With ac equivalent circuit analysis we view the capacitors effectively as shorts. Notice that the source is at ground and RD and RL are in parallel.

Common-Source Amplifiers
The load (RL) must be considered when viewing the ac equivalent circuit of an FET amplifier, RL is in parallel with the drain resistor (RD). This will lower the gain by lowering the overall drain resistance which is represented by Rd. Calculation for Rd can be determined by parallel resistance calculation methods. Once Rd is determined the voltage gain can be determined by the familiar gain formula below.

Av = gmRd

D-MOSFET Amplifier Operation


With this zero biased D-MOSFET amplifier it is quite easy to analyze the drain circuit since ID = IDSS.

D-MOSFET Amplifier Operation


With a zero-biased DMOSFET amplifier the swings occur in both enhancement mode and depletion mode. The methods for ac analysis for the D-MOSFET amplifier is identical to the JFET amplifier discussed previously.

E-MOSFET Amplifier Operation


For a voltage-divider biased E-MOSFET circuit the voltage divider sets the VGS needed to set the Q-point above the threshold. DC analysis of the drain circuit requires determination of the constant (K) from the formula discussed in the previous chapter.

E-MOSFET Amplifier Operation


Notice that with the E-MOSFET amplifier operation occurs exclusively in the enhancement mode. Voltage gain calculation for the E-MOSFET amplifier is the same as the JFET and D-MOSFET.

K = ID(on) /(VGS - VGS(th))2 ID = K(VGS V GS(th))2

Common-Drain Amplifiers
The common-drain amplifier is similar to the commoncollector BJT amplifier in that the Vin is the same as Vout with no phase shift. The gain is actually slightly less than 1. Note the output is taken from the source.

Common-Drain Amplifiers
The common-drain amplifier is basically has many similarities with BJT Common Collector/Emitter Follower. Input resistance must be seen as a parallel of RIN(gate) which depends on IGSS and RG. Based on the below diagram, start drawing the AC equivalent circuit!

Common-Drain Amplifiers
Back to basic definition: Av = ? Firstly derive Vout : ? Secondly Vin: ? And?

Common-Drain Amplifiers
Back to basic definition: Av = Vout/Vin You may use Id=gmVgs to simplify the equation

Common-Drain Amplifiers
Determine Av, total Rin considering gm=1000microS and IGSS=5nA at Vgs=20V.

Common-Drain Amplifiers
Determine Av, total Rin considering gm=1000microS and IGSS=5nA at Vgs=20V. Answers: Av=0.909 Rin=10Mohm Try Q24:Av=0.8,Rin=10M

Common-Gate Amplifiers
The common-gate is similar to the common base BJT amplifier in that it has a low input resistance. The voltage gain can be determined by the same formula as used with the JFET commonsource amplifier. The input resistance can be determined by the formula below.

Troubleshooting
A solid fundamental understanding of the different types of circuits is more valuable than simply memorizing the formulas to achieve the correct solution. The purpose of the formulas is to prove approximations and better understand what is taking place in a circuit. We as technicians are often called upon to work without the aid of specific test procedures or perhaps even worse poorly written ones. Making use of sharp intuitive skills is critical particularly with troubleshooting.

Rin(source) = 1/gm

Troubleshooting
With the skills acquired thus far, lets discuss some of the effects of various shorts and opens in this two stage FET amplifier circuit. Certainly knowing what is normal is helpful so basic analysis of the circuit must be done first.

Summary
FET amplifier configuration operation are similar to BJT amplifiers. The transconductance (gm) relates the drain current (ac output) to the ac input voltage (Vgs) Gain can be affected by drain circuit resistance. The input resistance for a FET at the gate is extremely high The common-source is the most used type of FET amplifer and has a phase inversion is 180.

Detailed description of the analysis is within the text.

Summary
The common-drain has no phase shift, a gain slightly less than 1 and the output is taken from the source. The common-gate has no phase shift and low input resistance.

You might also like