Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 1 of 43

Public Address System


1.0 System Design Procedure

Public address systems of various scales are used in all fields of today's world for
various purposes at various locations. A system engineer designs a system suitable to
a specific application. In all cases, he starts it with preparing a system plan for the
customer, involving the purpose of use, budget, and specifications.

Toward achieving an appropriate system design within the budget of the system plan, it
is important to clarify the main purpose of acoustic devices to be used and to decide
whether to select or not to select incidental functions (such as additional functions
which may be of help if provided). It is also necessary in selecting system components
to carefully study not only their performance but the ease of operation and the use of
PA system as well as reliability (i.e., capability of performing the intended motion
whenever required). A general system design procedure is shown in the flow chart
given.


































Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 2 of 43






















































Flow Chart for System Design

NO
YES
Construction drawings (layout, plane figure, cross
sectional view) obtained
Public address systems purpose of use, requirements,
specification, and budget determined
Acoustic characteristics of the installing location (noise level,
reverberation, echo, etc) and environmental conditions studied
An outline of the public address system and its location
determined
Selecting speakers
Selecting amplifiers
Selecting microphones
Selecting related products
Modifications: determine specifications of specially
ordered items
Piping and wiring materials selected
Kinds and quantities of wiring materials determined
Selecting pipes and ducts
Selecting parts necessary for wiring and equipment
installation
Construction drawings (layout, plane figure, cross
sectional view) obtained
Drawings (system block diagram, layout, specification,
wiring diagram, etc) prepared
Quotation prepared
Approved?
START
INSTALLATION
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 3 of 43


2.0 Acoustic Design Basics

The first problem raised in designing a public address system concerns the noise and
acoustic characteristics of the place where the system will be installed. Noise can be
generally classified into two kinds, that is, noise inside the building, and noise outside.
Noise inside the building includes, for example, the noises produced by the elevators
and air conditioners, talking people, machines at work, and the goods carried on the
floor. Outside noise may be such that produced by traffic, construction work, waves of
the sea, or running water in a river. It generally varies much depending on the kind of its
source, its distribution, the topography, and the buildings in the neighborhood. It can
also vary greatly from time to time. The acoustic characteristics can pose a problem
particularly when a public address system is installed indoors. The main factors
involved are reverberation and echo.

A room that has walls of a heavy and hard material with small acoustic absorptive (for
example, concrete, slate, or plywood walls) generally has a long reverberation time.
Specifically, slate covered factories in the shape of a dome, parking areas in buildings,
and gymnasiums have a long reverberation time. Reverberation lowers sound clarity,
and is detrimental to acoustics at low frequencies, particularly in rooms which are not
acoustically well designed. Echo is a reflection of the original sound heard later.
Reflected sounds reaching the ear within 1/20 second (50 mS) from the direct sound
reinforce the original sound so that they sound like a signal sound with reverberation. If
reflected sounds reach the ear later than that, the reflected sounds are heard as an
echo because they sound separate from the direct sound. The echo so seriously affects
sound clarity that it makes a music performance impossible. It is the most harmful of all
acoustic ill effects.

Outdoor echoes, such as caused by winds, mountains buildings, and topographical
features, also pose a problem. When selecting speaker locations, therefore, high places
where the speakers can take best advantage of fair winds, and places less likely to be
troubled by echoes are chosen. Another way of coping with this problem is to locate
small-powered speakers at many points.

2.1 Noise and Speaker Sound Pressure

If noise level is higher than the level of the sound coming out of the speaker, the
speaker sound cannot be heard. No matter how close the speaker may be its sound
cannot be heard if noise level is too high. The required difference between speaker
sound and noise levels varies depending on the kind and degree of noise, but at least a
sound pressure difference of 6 to 10 dB (2 to 3 times) is necessary for making
announcements, or at least about 3 dB (about 1.5 times) for background music or other
music programs.

For your reference, noise levels at various locations are shown in me table below.










Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 4 of 43

Noise Levels

Near jet aircraft engine 120 dB
Under railway girder 100 dB
Road intersection 80 dB
Noisy office 60 dB
Suburban housing area 40 dB
Tree leaves rustling in breeze 20 dB
Minimum audible sound 0 dB

Note: Generally, noise level is high at low frequencies, and low at high frequencies.
Noise level is measured with a noise meter, and measured noise levels in WRMS are
used.

2.2. Speaker Output Sound Pressure and Sound Attenuation

Output sound pressure Speaker specifications include output sound pressure, which
represents the sound volume that can be produced by the speaker, measured by
applying a 1-watt input to the speaker and measuring the sound one meter away from
it.







Output sound pressure is expressed in decibels (dB), which is equal to phone used to
express noise used to express the same in noise calculations Output sound pressure
also represents the speaker capacity (or efficiency) of converting electrical signals into
sound, which varies from 85 dB to 110 dB with the kinds of speakers.


Difference in output sound pressure with kinds of speakers

Speaker Output sound
pressure
Ceiling / wall mount speaker 85 to 93 dB
Column gymnasium speaker 90 to 106 dB
Horn speaker 95 to 110 dB


What will be the output sound pressure level if a higher input of 2 watts and more is
applied to the speaker? The output sound pressure increases as shown in the table
below.

Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 5 of 43



Speaker Input versus Increased Sound pressure

Speaker
input
Increased
sound
pressure
Speaker
input
Increased
sound
pressure
1W 0dB 16W 12dB
2W 3dB 20W 13dB
3W 5dB 25W 14dB
4W 6dB 30W 14.8dB
5W 7dB 32W 15dB
6W 8dB 40W 16dB
7W 8.5dB 50W 17dB
8W 9dB 60W 17.8dB
9W 9.5dB 70W 18.5dB
10W 10dB 80W 19dB
13W 11dB 90W 19.5dB
15W 11.8dB 100W 20dB

Note: A double input gives an increase of 3 dB

watts is applied to the speaker = (Output sound pressure in dB in the speaker
specifications) + (Increased sound pressure in dB).

Example 1: A 3-watt input is applied to WS-4600GN



The output sound pressure of the WS-4600GN is 92 dB (1 m, 1W). If a 3-watt input is
applied, the sound pressure in creases by 5 dB. Thus, 92 dB + 5 dB = 97 dB (1 m).


Example 2: A 15-watt input is applied to WT-715N



The WT-715N is a horn type speaker called the CLEARHORN, which features a high
output sound pressure of 101 dB (1 m, 1 W). If a 15-watt input is applied to it, 101 dB+
11.8 dB = 112.8dB (1 m).

As is clear from the two examples above, the higher the output sound pressure, the
higher sound can the speaker produce more efficiently.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 6 of 43


In terms of amplifiers, the same sound pressure can be obtained from a smaller powered
amplifier if the speaker has a high output sound pressure. Assume that we now have a
87-dB speaker and a 90-dB speaker here, for example;

Output Sound Pressure and Required Input Power



To produce a sound pressure of 90 dB from the 87 dB speaker, its output sound
pressure must be increased by 3 dB. This means that a 2-watt input must be applied to
the 87-dB speaker.

Thus, if speakers that have a difference of 3 dB in sound pressure are used, an
amplifier with twice the output of the other must be used. If the difference is 6 dB, an
amplifier with four times the output power must be used. If the difference is 9 dB, an
amplifier eight times as powerful is required.

What will be the total output sound pressure in dB if two or more speakers, each with an
output sound pressure of X dB, are installed in the same place in the same direction?

If a 1-watt input is applied to two 90-dB speakers, their total output sound pressure
increases by 3 dB to 93 dB, which is the same as when a 2-watt input is applied to one
of them.

If a 1-watt input is applied to three 90-dB speakers, the result will be same as when a 3-
watt input is applied to one of them. That is, the total output pressure increases by 5 dB
to 95 dB.

Increased Sound Pressure Where Two or More Speakers of the Same Capacity
Are Installed in the Same Place


Number of speakers Increased sound pressure
1 0 dB
2 + 3 dB
3 + 5 dB
4 + 6 dB

Incidentally, the rated output sound pressure of a speaker applies where a certain
specified sound source, not a speech or music, is used. In the past, the required sound
pressure was often calculated from the rated output sound pressure. This, however,
does not have a peak factor (allowance for speeches or music) so that .sound becomes
distorted at peak level




Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 7 of 43


Therefore, we calculate the required sound pressure by adding the peak factor for the
peak of the program source to the required sound pressure difference, which is the
difference between noise level and the average sound pressure of the program source.

Sound clarity increases as the required sound pressure difference increases. A.
difference of about 6 to 10 dB between noise and the average sound pressure of the
program source is normally sufficient.

The peak factor (the difference between the average sound pressure and peak sound
pressure of a program source) varies from one program source to another, but it is 10
dB for speeches and background music, or 20 dB for music.

This can be summarized as follows:


Required sound pressure = Noise level + Required sound pressure
difference + Peak factor


Speeches and Background Music

Required sound pressure
= Noise level + (6 to 10 dB) + 10 dB
= Noise level + (16 to 20 dB)

Music

Required sound pressure
= Noise level + (6 to 10 dB) + 20 dB
= Noise level + (26 to 30 dB)
























Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 8 of 43


The table below shows the required sound pressures at various locations


Noise effect Noise
level
(dB)
Description Required sound pressure
If noise level is 100 dB or more, a
sound pressure of more than 120 dB
(maximum audible sound level) may be
necessary (varying depending on noise
frequency) so that announcements will
be hardly audible.


Conversation
inaudible


Conversation
hardly audible
100 dB or more
Must speak
aloud

70 to 90 dB







Normal
conversation
possible






120

110

100

90

80

70

60

50

40

30

20

10

0
- Near aircraft engine

- Siren, automobile horn

- Under railway girder, inside
electric train
- Machine shop

- Road intersection, printing
shop
- Department store, noisy
office
- Restaurant, hotel lobby,
office, urban housing area
-..

- Suburban housing area,
hospital, hotel
- Broadcasting studio

- Tree leaves rustling in
breeze
- Whisper

- Minimum audible sound





70 dB or more
(Noise can be nearly
ignored)






Where music is
the primary
sound source, 80
to 100 dB








2.3 Sound Attenuation

Speaker output sound decreases in volume as the distance from the speaker increases.
Sound volume (sound pressure) decreases in inverse proportion to the square of
distance.

The table below shows sound attenuation outdoors (wherein air density difference,
temperature difference, wind direction, reflection from obstacles, refraction, etc. are
ignored).








Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 9 of 43


Distance from Speaker and Sound Attenuation in Free Space
























Sound attenuation indoors is less than that in free space, varying depending on the
acoustic characteristics of the room. Generally, public address systems are designed
with sound attenuation in free space as reference, using the above as peak factor.

Sound attenuation also varies with frequency. That is, a high-frequency sound
attenuates more than a low-frequency sound.

Sound Pressure Attenuation Indoors Versus Distance



The sound pressure at a point a certain distance away from the speaker is calculated
as follows:

[Output sound pressure (dB) where an input of a certain wattage is applied]
(Attenuation by distance (dB)].
Distance Attenuation Distance Attenuation
1 m 0 dB 28 m 29 dB
2 m 6 dB 30 m 29.5 dB
3 m 9.5 dB 32 m 30 dB
4 m 12 dB 36 m 31 dB
5 m 14 dB 40 m 32 dB
6 m 15.5 dB 45 m 33 dB
7 m 17 dB 50 m 34 dB
8 m 18 dB 56 m 35 dB
9 m 19 dB 60 m 35.5 dB
10 m 20 dB 64 m 36 dB
11 m 21 dB 70 m 37 dB
13 m 22 dB 80 m 38 dB
14 m 23 dB 90 m 39 dB
15 m 23.5 dB 100 m 40 dB
18 m 25 dB 150 m 43.5 dB
20 m 26 dB 200 m 46 dB
22 m 27 dB 300 m 49.5 dB
25 m 28 dB 400 m 52 dB
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 10 of 43


Suppose that the rearmost seats in an auditorium are 25 meters away from the
speakers. The speaker output sound pressure required to reach them at 80 dB level is,
by compensating for attenuation of the original sound pressure:

80dB+28dB = 108 dB.

Example 1:

What wattage of input must be applied to the speakers of a PA system in an office?

Step 1

Suppose that the noise level indoors is 60 dB. If the required sound pressure difference
is 6 dB, the required sound pressure will be, by adding a peak factor of 10 dB:

Required sound pressure = Noise level + Peak factor + Required sound
pressure difference

= 60dB + 10dB + 6dB

= 76dB.

Step 2

A sound pressure of 76 dB is required at the listening points, which are 1.7 meters
away from the speakers.

This means an attenuation of about 5 dB.

Speaker sound pressure = Required sound pressure + Attenuation
by distance
= 76 + 5
= 81dB.

Step 3

To achieve a uniform sound pressure, the speakers are so arranged that their
directional angles cross at the listening points on condition that their service area is 90
each.

Speaker to speaker distance = 2 x (2.7 m 1 m) = 3.4 = 3 m

Thus, the speakers are installed on the ceiling 3 meters apart.

Step 4

Selecting a speaker:

The WS-4150N was selected as a ceiling speaker. This speaker has an output sound
pressure of 92 dB (1 m, 1 W) so that enough sound volume can be obtained even if an
input of about 0.1 watt is applied to it.

Actually, the total input wattage is the input wattage per speaker multiplied by the
number of speakers
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 11 of 43




Example 2:

What wattage of input must be applied to the speakers of a sound reinforcement system
in, for example, a gymnasium or auditorium?

Step 1

Suppose that the noise level at the audience seats is 60 dB. If the required sound
pressure difference is 6 dB, the required sound pressure will be, by adding a peak factor
of 20 dB:

Required sound pressure = Noise level + Peak factor + Required sound pressure
Difference

= 60dB + 20dB + 6dB

= 86dB.

Step 2

Even the rearmost row of seats must have a sound pressure of 86 dB. Because it is 14
meters away from the speakers, the original sound pressure will be attenuated by 23 dB.

Speaker sound pressure = Required sound pressure + Attenuation by
distance

= 86dB + 23dB

= 109dB.

Step 3

As shown, a speaker sound pressure of 109 dB is necessary. Because two speakers are
used here, the required sound pressure per speaker is 109 dB minus 3 dB, that is, 106
dB.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 12 of 43

Step 4

Next is the selection of a speaker model. Here, the WS-3200N was selected. The WS-
3200N has excellent directivity and provides satisfactory performance for music as well.
The output sound pressure of the WS-3200N is 95dB.

Increased sound pressure = Speaker sound pressure - Output sound pressure

= 106dB - 95dB

= 11dB.

This can be obtained by applying a 13-watt input. The selection of the WS-3200N is
correct because its rated input is 15 watts.






2.4 Sound Insulation and Transmission

Sound insulation and transmission have two meanings. One is to shutting out the
sounds or announcements that originate in the next room, and the other is to transmit
sounds or announcements through a door, for example.


These are calculated as follows:


Transmitted sound pressure (dB)
= Incident sound pressure (dB) Transmission loss (dB)



Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 13 of 43


Example 1:


Sound pressure (dB) at the listening point

= 90dB - (Loss at 2 m: 6 dB) - (Transmission loss: 20 dB) - (Loss at 3 m: 9.5 dB)

= 54.5 dB.

Under this condition, the sound from the speaker is louder than the noise level at the
listening point, and can be heard through the door.

Transmission Losses

Glass window (3mm thick) Approx. 10 dB
Wooden door (9mm thick) Approx. 25 dB
Concrete block (100mm thick) Approx. 45 dB
Concrete (100mm thick) Approx. 50 dB


2.5 Frequency Characteristics (Effect of a graphic equalizer)

The human ear is sensitive to sounds of 2,000 Hz to 6,000 Hz. In other words, one of
the conditions for good audibility is to produce aloud sounds of 2,000Hz to 6,000Hz.

Each building or room has its own reverberation time frequency characteristic, which
means the reverberation time characteristic of that building or room against sounds
from low to high.

Generally, gymnasiums and auditoriums have such a structure and interior materials
that bass sound can hardly be absorbed. That is, bass sound lingers on and thus is
emphasized.

Suppose an acoustic system having a very flat characteristic is used in a gymnasium.

The actual sound in a gymnasium having a reverberation time frequency characteristic
such as shown in Fig. 1 will be as shown in Fig. 2. If bass sound is emphasized, the
sounds within the range of 2,000 Hz to 6,000 Hz that are necessary for, clarity fall,
resulting in less clear sounds.








Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 14 of 43





A graphic equalizer for sound field correction electrically corrects this phenomenon.

The graphic equalizer can vary sound level at every certain frequency. If the power
response is as shown in Fig. 2, the graphic equalizer suppresses the sounds of up to
1,000 Hz, and slightly raises treble sounds of 2,000 Hz and upward.

Clarity can be raised as described above.
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 15 of 43


3.0 Speaker Selection

Speaker selection and arrangement is so important that the performance of an acoustic
system depends mostly on it. Such troubles as poor clarity and lack of volume are often
caused by the wrong selection or arrangement of speakers.

3.1 Kinds of Speakers

Speakers can be roughly classified into indoor and outdoor types, which can be further
broken down by place of use and purpose of use as shown in the table below.



The required reproducing frequency bandwidths of specters by use are explained.

a) Public address
b) Generally, a frequency band of about 200 to 6,000 Hz can achieve the purpose. In
the worst case, the required frequency band is from about 250 to 4,000 Hz, which
corresponds to the voice frequency band of man.
c) Background music
d) Background music, including music in a light sense of the word, requires a
frequency band of about 100 to 8,000 Hz.
e) Music

In a hall primarily designed for amplifying music, a frequency band of about 40 to 5,000
Hz is necessary.

Therefore, conditions for music reproduction are stricter than in the other cases, and
special care must be taken in selecting speakers for it.

3.2 Speaker Arrangement

Speaker arrangement varies with the electrical input to be applied and speaker
efficiency as mentioned before. Where speakers are used indoors, the purpose of use,
acoustic characteristics (reverberation, echo, and sound insulation), and speaker
directivity must also be taken into account. Where speakers are used outdoors, weather
resistance to winds and rains must be additionally considered.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 16 of 43


Generally, there are three types of speaker arrangement normally applied in sound
system design:-

3.2.1 Centralized system

This system places speakers in a centralized position to operate in a single direction;
and has the advantages of providing a directional sense and low installation cost. The
former is particularly effective for lectures, speeches, and concerts where the visual
direction must meet the sound direction.

It also has disadvantages: Difficulty of providing a uniform level; poor clarity caused by
reverberation and echo; and large output power required where noise level is high. In
factories where much noise is produced, the dispersed system mentioned next is
suitable.




3.2.2 Dispersed system

This system uses speakers in a dispersed arrangement. It is suitable to background
music because it provides uniformity of sound level. If a small electric input is applied to
one of the speakers to narrow the audible range, sound reflection decreases so that
clarity can be increased where reverberation time is long.

If many speakers of the system interfere with one another, it can lower sound quality.
The important point for the dispersed system is to correctly select a number of speakers
and the operating range of each speaker.

The dispersed system costs more to install than the centralized system.

Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 17 of 43



3.3 Composite system

This is a combination of the centralized system and the dispersed system. It uses
centralized speakers to achieve the intended sound pressure and small powered
auxiliary speakers in a dispersed arrangement at points where sound pressure is short
of the required level. The composite speaker system is frequently seen in auditoriums
and gymnasiums.

3.3.1 Speaker Arrangement Indoors

a) Restaurants, Offices, Stores because the ceiling is generally low, install many
ceiling mount speakers of about 1 W to 3W. Determine a number of speakers
suitable to the room size.



Install speakers zigzag to achieve a uniform sound.

Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 18 of 43


Ceiling height and the coverage of each speaker

The following table applies where noise level is 60 dB, the peak factor 10 dB, and
the required sound pressure difference 6 dB.


Ceiling height Speaker spacing Coverage of one
speaker
Input per speaker
2.5 m 3 m Approx. 9 m 1 W
3.0 m 4 m Approx. 16 m 1 W
3.5 m 5 m Approx. 25 m 1 W
4.0 m 6 m Approx. 36 m 3 W
5.0 m 8 m Approx. 64 m 3 W


b) Classrooms and Offices

Select 1-to 6-watt wall mount speakers suitable to the room size.


Distance from wall and the coverage of each speaker

The following table applies where noise level is 60 dB, the peak factor 10 dB, and the
required sound pressure difference 6 dB.







Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 19 of 43


Distance from wall Speaker spacing Coverage of one
speaker
Input per
speaker
Up to 4 m 4 m Approx. 16 m 1 W
Up to 7 m 7 m Approx. 50 m 3 W
Up to 9 m 8 to 16 m Approx. 100 m 5 W


Do not install the wall mount speaker facing each other. If wall mount speakers are
installed facing with each other the sound clarity will be degraded.

As bi-directional wall mount speaker (1750N) emits sound in both directions, it is
suitable for wide space or narrow, long areas such as lobbies, waiting rooms or
passage ways of hotels, theaters, movie theaters, hospitals, railway stations,
airports, etc.
.


c) Meeting Rooms, Conference Rooms, Gymnasiums

Select 15-W or 30-W 2-way column speakers suitable to the room size




Install the speakers about 4 meters to the front side on the stage, from where the
microphone is located. Select a number of speakers and their model from Table (A)
where the speakers are intended for music; or from Table (B) where they are mainly for
speeches.

There must be a difference of 20dB or more between the peak sound pressure and
noise.



Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 20 of 43




d). Noisy Rooms

Noise level about 90 dB

If noise level is 90 dB, a sound volume of 96 to 100 dB is necessary.

Use horn speakers which are efficient.


















Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 21 of 43


Horn speaker Distance for obtaining 100 dB
at peak output
Speaker spacing
5 W Approx. 3 m Approx. 3 m
10 W Approx. 4.5 m Approx. 4 m
15 W Approx. 7 m Approx. 6 m
30 W Approx. 11 m Approx. 10 m

Horn speaker Distance for obtaining 96 dB at
peak output
Speaker spacing
5 W Approx. 5 m Approx. 4 m
10 W Approx. 7 m Approx. 6 m
15 W Approx. 11 m Approx. 10 m
30 W Approx. 17 m Approx. 15 m

Noise level about 100 dB

If noise level exceeds 100 dB, the speaker sound cannot be distinguished from the
noise even if the volume is raised above the level.

If noise level is about 100 dB, install a horn speaker of about 5 to 10 watts near each
listener.



e) Speaker Arrangement Outdoors

i) Factory premises

Install horn speakers or CLEARHORN speakers of 7 or 15 watts on the premises at the
necessary position in a dispersed way.

If speaker sound (sound within a vertical dispersion range of 60) directly hits the
building opposite the speaker, its reflected sound adversely affects clarity. Install the
speakers so that the upper limit of the vertical dispersion range will be at the ground
level of the opposite building.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 22 of 43





ii) Streets and shopping centers

Install horn speakers or CLEARHORN speakers of 7 or 15 watts in a dispersed
way.
Speakers may be installed by either method A or B, but method B is
recommended because it provides better sound uniformity and clarity than
method A.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 23 of 43






iii) Athletic fields, parks, etc.

Install horn speakers or weatherproof column speakers of 20 or 30 watts in a
centralized arrangement.
Install the speakers on building roof or on top of a pole, or other elevated
location.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 24 of 43







f) Mosques, etc.

Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 25 of 43



Install horn speakers of 30 to 50 watts at as high a place as possible. Install
them in a circular arrangement to emit sound in all directions.



If sound pressure is not enough with a single speaker, combine plural speakers
vertically to provide directivity.



Where speaker sound must reach far and wide, speaker output power

must be somewhat greater than normal because the effects of winds, topography,
temperature difference, and noise variations cannot be ignored.

Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 26 of 43



4.0 Amplifier selection

After determining speaker arrangement and the required input to each speaker, the
total required input (wattage) can be calculated, and an amplifier that has an output
power corresponding to it can be selected. Select an amplifier on the basis of, not the
maximum output, but the rated output wattage. If additional speakers are planned to be
installed in the future, take this into account in selecting an amplifier wattage.

The number of input and output terminals, input and output impedances and levels
must also be studied. Performance wise, frequency response, signal-to-noise ratio, and
distortion factor also need to be examined. If the speakers are used exclusively for
music, the specifications must also be more strict than in other applications.

4.1 Amplifier Wattage Selection from Speakers

Too small an amplifier output cannot produce enough sound volume, whereas too great
an amplifier output can damage the speakers due to the excessive input applied to the
speakers. This problem is particularly true of low-impedance speakers.

a) High-impedance speakers

A system involving multiple speakers normally uses high-impedance speakers
connected parallel. As you know, the combined impedance of speakers connected
parallel is smaller than the impedance of the individual speakers. It is necessary for an
amplifier to meet the following condition in order to drive speakers properly.



Therefore, an excessively large number of speakers cannot be connected to an
amplifier. To allow simple designing of such a system, the output voltage of the
amplifier is regulated at constant level. This is called a 100-V line or 70-V line. A large-
output amplifier may be described as one which can supply a large current at a
constant voltage.

Because the amplifier output voltage is constant, the input power applied to the
speakers can be automatically determined from the input impedance of each speaker.
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 27 of 43

As many speakers as desired can be connected to an amplifier if their total input is
within the limits of the rated output of the amplifier.




Example 1: WS-4000BN

The input impedance is 3.3 k ohms or 10 k ohms. If it is 3.3 k ohms where a 100- V
line is used,




If the amplifier with an output power of 30 watts is used, up to ten speakers can be
connected to it if the input impedance is 3.3 k ohms; or up to 30 speakers can be
connected to it if the input impedance is 10 k ohms. Since the output sound pressure of
the WS-4000BN is 92 dB, sound pressures of 97 dB and 92 dB can be produced
respectively. (Sound pressure increase by 3-watt input is 5 dB).Maximum numbers of
speakers to be connected to typical models are shown in the table below










Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 28 of 43


Example 2:

What amplifier output wattage is necessary for the speakers connected as shown
below?



Calculate W1 to W6 for each speaker, and select an amplifier that has an output greater
than the calculated total.








The above condition is satisfied by an amplifier with a rated output of 30 watts. The WA-
320N or WA-730N, for example, may be selected. Remember not to select an amplifier
output by simply totaling the rated inputs of the speakers to be used. This method,
however, can end with the same result in some cases.
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 29 of 43


4.2 Low-impedance speakers

If low-impedance speakers are used, the amplifier delivers its full output power. Even in
this case, the following conditions must be met. Rated amplifier load impedance (ohms)

Example 1:

If the volume is raised in a connection as shown below, the 30-watt output of the
amplifier is fully applied to the speaker and damages the 15-watt speaker.

Example 2:

In a connection as shown below, only a 15-watt input is applied to the speaker because
the speaker impedance is double the amplifier impedance of 4 ohms.

5.0 Microphone selection

In selecting a microphone, directivity, frequency response, impedance, balanced or
unbalanced type, etc .must be studied depending on the purpose of use and the
location.

The wrong use can cause poor tonal quality, lack of volume, or howling. It is important,
therefore, to fully explain the correct method of using the microphone to the user.

First, select a place of use, and a type of microphone suitable to the purpose of use. It
is necessary for this purpose to be fully familiar with the basic characteristics of the
microphone.

5.1 Types of microphone
(Based on method of signal generation)

5.1.1 Condenser microphone*

A microphone utilizing a capacitor (condenser) as a pickup element. Electronics are
usually contained in the microphone body and a polarizing voltage is necessary; so
external or battery power is required, and output levels are usually higher than other
types of microphones. Condenser microphones are commonly used for high quality
audio applications.

5.1.2 Electrets condenser microphone*

A variation of a standard condenser microphone where the element is permanently
charged so no external polarizing voltage is necessary. However, due to the electret's
very high impedance, an electronic impedance converter is usually built in and does
require a small amount of voltage from a battery or external supply.

Electrets condenser microphones have similar characteristics to condenser
microphones. Their small size and light weight make them particularly suitable for
studio use (tie-clasp livelier microphones etc.) and for speech microphones in which
clear tones are required.




Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 30 of 43


5.1.3 Dynamic microphone*

A type of microphone which converts acoustical to electrical energy by means of a
permanent magnet and a moving coil. Dynamic microphones do not require external
power.

As dynamic microphones are rugged in construction, they provide stable performance
and are easily handled. They generate minimum noise when used in windy conditions,
and as such they are used in speech and vocal applications.

[* Partially from the CAMEO/Dictionary of Creative Audio Terms]

5.2 Microphone Sensitivity

If a 1,000 Hz tone of 1 bar (microbar) is applied to a microphone at a distance of 50
cm, and if it produces an output of 1 V, this microphone has a sensitivity of 0 dB. That
is, microphone sensitivity represents the capacity of quantitative conversion from sound
into electricity. Incidentally, a tone of 1 bar is equivalent to a speaker output sound
pressure of 74 dB, which is the level of an ordinary
human voice heard at a close distance.

A -50dB microphone has higher sensitivity than a -70dB microphone by 20 dB. If a
50dB amplifier is used, its output will be 0 dB.




5.3 Microphone Frequency Response

Generally, the range of frequencies audible to the human ear is about 20 to 18,000 Hz.

A microphone is considered having good characteristics if it has a wide frequency band.
But a microphone having the required frequency range, through it may be somewhat
narrow, can well serve the purpose depending on what it is used for. In paging
applications, for example, a microphone that can cover the human voice frequency
range of about 150 to 6,000 Hz is satisfactory for the purpose.

A microphone with the unnecessary portion of the bass range cut off can rather permit
amplification of clear sound with less "confinement" of sound.

It is important, therefore, to select the correct microphone for the purpose.

5.4 Microphone Directivity

Directivity means the sensitivity difference of a microphone in the direction of the sound
source, and can be generally classified into two kinds as follows:
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 31 of 43


5.4.1 Unidirectional (cardioid)*

A microphone with a heart-shaped pickup pattern that is sensitive to sound in the
forward direction(0
o
) and rejects sound from the rear of the mic (180). At the sides (90
and 270) the cardioid is about half as sensitive as the front.

This type of microphone is suited to use in cases in which only a selected sound is
required. Since it is resistant to howling when used in public address systems, it is
commonly used for a wide variety of purpose.



5.4.2 Omni directional*

A microphone that is equally sensitive to sounds in all directions. This type of
microphone is suited to use in cases in which the selected sound, as well as reflected
sound, and other sounds in the area, are required to give an impression of the
surrounding sound environment.

[* Partially from the CAMEO/Dictionary of Creative Audio Terms]




5.5 Output Impedance

The output impedance of a microphone means the impedance of its terminal which is
connected to an amplifier. It is necessary to match the input impedance of the amplifier
with the output impedance of the microphone. Actually, however, a microphone may be
connected to an amplifier having impedance higher than the microphone output
impedance.

Microphones come in two output impedances, high and low. An impedance of 10 k
ohms or more is called high impedance; and an impedance of 600 ohms or less is
called low impedance. There are also dual impedance type microphones, which can be
easily converted from one impedance to the other or not verse with a switch or by
changing the plug and internal connections.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 32 of 43












Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 33 of 43


5.6 Balanced Type, Unbalanced Type

The noise induced in the microphone cable is amplified together with the voice signals
by the amplifier.

Therefore, all microphones use a shielded cable to prevent externally induced hum and
noise. The type which uses a two-conductor shielded cable is called the balanced type;
and that which uses a single-conductor shielded cable is called the unbalanced type.





The balanced type is recommended where the microphone is used far away from the
amplifier because it is less susceptible to externally induced noise and provides
constant tonal quality. In this case, however, the amplifier must have a balanced type
input terminal. Some unbalanced type microphones use a two-conductor shielded
cable. These microphones can be converted to the balanced type if its TS phone plug is
changed to a TRS phone plug or a XL-type connector.

Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 34 of 43




5.7 Microphone Selection

Select a suitable microphone by referring to the foregoing explanation. Here are
typical examples of microphone selection.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 35 of 43



Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 36 of 43










Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 37 of 43


6.0 Connecting Speakers

6.1 Basic Connection

The output stage of the HI-POWER AMP (and other amps as well) contains an output
transformer. This transformer is wired as follows.

Connect speakers so that the COMMON terminals are connected to (-), and the 4-ohm
terminal of the low-impedance speaker, or the 100-V or 70-V terminal of the high-
impedance speaker, is connected to (+) (low- and high-impedance terminals cannot be
used simultaneously, 100-V and 70-V lines cannot be used simultaneously). As the
rated load impedance of the 70-V line is half that of the 100-V line, twice the quantity of
speakers can be connected when the 70-V line is used (the speaker input, however, will
be half that for the 100-V line). For these reasons, the 70-V line is used in cases such
as BGM broadcasting in which a large number of speakers with relatively small input
rating are used.




6.2 Using Volume Controller

Volume controller may be used only with high-impedance speakers. The wiring for the
volume controller is of either the 2- or 3-wire system. Volume control for each speaker is
possible with both the 2- and 3-wire systems. However, when it is OFF, emergency
announcement is impossible in case the 2-wire system is used; but possible in the 3-wire
system.

The user should be advised to note that the 2-and 3-wire volume controls are exactly the
same. As is obvious from the circuit diagram above, ALL terminal is normally connected
to COMMON. However, when the all-speaker switch is ON, it is connected to the 100-V
output of the output transformer. Since accurate attenuation is not obtained if the volume
controller is not suited to the impedance of the connected speaker, a volume controller
having the same wattage rating (or a wattage rating within the specified range) as the
speaker must be selected. A number of speakers can be connected and controlled
together by a volume controller within the specified rating.


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 38 of 43

Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 39 of 43




a) Speaker Wiring

As wiring between the amp and speakers must be designed with consideration for
transmission losses, line loop resistance must be no more than 10% of the
combined impedance of the speakers or the rated load impedance of the amp.

For Example:

If the rated load impedance of the amp is 330 ohms and wiring is 1.0 mm in
diameter, what is the maximum length of the wiring?






The line resistance of annealed copper wire (single strand) is 22.9n/km (at 20C). The
maximum length of wiring is calculated with the following equation:

Loop resistance < = 10% of the rated load impedance

2 x 22.9L < = 330 x 0.1
L < = 0.72

The maximum length of wiring, therefore, is approximately 700m.Maximum allowable
distance between an amplifier and a speaker is shown below.



Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 40 of 43



6.3 Radio Antennas

6.3.1 AM Radio Antennas

AM radio antennas are always required. In strong broadcast areas, a 2- to 5-m vinyl-
covered wire should be attached to the wall or ceiling in a horizontal attitude and as
high as possible. Coaxial cable should be used between the antenna and a radio tuner.















Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 41 of 43


Table 1: Guideline for Audio Visual Requirement and Criteria

NOTE: All sizes given may differ according to the sizes of the project.




NO ROOM TYPE
PROPOSED
SIZE (mm)
CRITERIA / GUIDE
1.0 General System


1.1 P.A. Equipment Room
2000 x 2500
1.2 Security Control Room 3000 x 4000
Can be combine within the Command Control
Centre
1.3 Riser Room 1200 x 900
For MATV / AV / Security / Sound Systems
Door kerb:100mm 150mm
1.4 Floor Opening
200(w) x
1200(l)
Will be covered by approved 2 hrs fire barrier
Door to follow UBBL
75mm kerb around the floor opening; 50mm
kerb across the door
2.0 Auditorium
Shall be acoustically treated and sound
insulated
Sound insulation required if metal roofing used
2.1 AV Control Room
4000(l) x
3500(w)

2000 x 900(h)

Fully carpeted, air conditioned
Full height partitioned (brickwall or sound
insulated partition)
Sliding glass window: tinted, 800mm from floor
level
2.2 SIS Cubicle / Room
1500 x 2000




1000 x 900(h)
Size is for one cubicle
Sound insulation shall follow ISO Std: i.e. full
height partitioned (brickwall or sound insulated
partition)
Fully carpeted, air conditioned
Glass window: tinted, 800mm from floor level
2.3 Back Projection Room 6000(d)
For fixed screen system, behind the stage /
screen
2.4
Stage
Cross beams and roof
supports

Required to support the I-beams across the
stage area: for all the lighting barrels and curtain
railings
Approximate load: 4000 kg
2.5
Catwalk
Ceiling Catwalk

For maintenance of stage equipments
Recessed catwalk within the acoustic ceiling for
maintenance
3.0
Meeting / Operation /
Seminar / Board Rooms
(Single volume rooms)

3.1 AV Control Room
2500 x 3000




1200 x 900(h)
Fully carpeted, air conditioned
Fully height portioned (brickwall or sound
insulated partition)
Sliding glass window: tinted, 800mm from floor
level
Sliding board built-ins required
Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 42 of 43

Appendix 1: Schematic Diagram of PA Systems


Chapter 12

Panduan Teknik Edisi Ke-4 2008 Cawangan Kejuruteraan Elektrik Pg 43 of 43

Appendix 2: Schematic Diagram of SMATV System