Scribd
Upload
36 views

Direct vs. Indirect Measurement - Continuous vs. Discrete Sensors - Incremental and Absolute

This document discusses different types of proportional feedback sensors and their uses. It describes direct vs indirect measurement, continuous vs discrete sensors, and absolute vs incremental encoding. It focuses on incremental encoders, explaining their resolution and how they provide relative position information. It also covers absolute encoders, hybrid encoders, potentiometers, and magnetostrictive sensors. Finally, it discusses high-speed input/output modes for a PLC, specifically modes 10 and 20 which are used for high-speed counting and quadrature counting. Troubleshooting tips are provided for mode 10.

Uploaded by

Tanvon Malik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
36 views

Direct vs. Indirect Measurement - Continuous vs. Discrete Sensors - Incremental and Absolute

This document discusses different types of proportional feedback sensors and their uses. It describes direct vs indirect measurement, continuous vs discrete sensors, and absolute vs incremental encoding. It focuses on incremental encoders, explaining their resolution and how they provide relative position information. It also covers absolute encoders, hybrid encoders, potentiometers, and magnetostrictive sensors. Finally, it discusses high-speed input/output modes for a PLC, specifically modes 10 and 20 which are used for high-speed counting and quadrature counting. Troubleshooting tips are provided for mode 10.

Uploaded by

Tanvon Malik
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 22

Proportional Feedback

Direct vs. Indirect Measurement


Continuous vs. Discrete sensors
Incremental and absolute
Direct vs. Indirect
Measuring position of a carriage is better
than measuring rotation of leadscrew
Measuring level in a tank or weight of a
product is better than measuring flow
Measuring temperature of an oven is better
than measuring heater current
Budget usually dictates whether direct or
indirect measurement will be used
Continuous and Discrete Sensors
Most sensors are analog, and give readings
on a continuous scale that must be
quantized for use with a PLC.
Position sensing can be done with encoders
that give a quantized reading to start with
Linearity and temperature coefficient are
usually limiting factors on accuracy of
continuous, analog sensors. Discrete
sensors are limited by resolution.
Absolute vs. Incremental
An absolute sensor gives a single,
unambiguous reading for a given position
An incremental sensor indicates an
incremental change in position
Incremental sensors require a separate
means of establishing home position
Incremental Encoders
Incremental encoders give relative position
information
count + and - relative motion
index pulse gives a once-per-revolution
signal
Resolution = 4x number of slots
establish absolute ref point each power-on
Incremental Encoders
Quadrature signal outputs
Single-ended vs. differential output
Absolute Encoders
doubling resolution requires adding another
photodiode/LED pair
cost is much higher than incremental
does not require seeking to establish
reference location
hybrid incr/absolute encoders
add more information to index channel to
reduce amount of seeking required to find
reference position.
Potentiometer
A potentiometer (or pot) is a variable
resistor wired to obtain a variable DC
voltage proportional to position
Magnetostrictive Sensor
High Speed Input/Output
High speed counters
Use X0,X1, and X2
Pulse Output
Uses Y0 and Y1
One of six modes can be used
Mode 10: High speed counter
Mode 20: Quadrature counter
Mode 30: Pulse Output
Mode 40: High speed interrupt
Mode 50: Narrow pulse capture
Mode 60: Narrow pulse reject (normal mode)
Mode 10 - High Speed Counter
Up counter, counts to 99,999,999
Up to 5kHz input rate (incr. on X0 low->hi)
Count is compared to preset values to
generate events.
Reset can be X2 or ladder logic
Mode 10 high Speed Counter
Used for applications like cut-to-length
Ex:
4096cnt/rev enc
10cm diam roller
rotate turret and
operate at 12, 20,
28, and 30cm
Presets are:
1565, 2608, 3651,
3913
1565
416 . 31
12 4096
D
dist
rev
cnts
Preset =

=
Mode 10 high Speed Counter
Mode 10 high Speed Counter
Setup consists of
writing values to
several special
memory locations
Mode 10 high Speed Counter
Mode 10 High Speed Counter
Troubleshooting Mode 10
Wont count:
check ladder logic (using CT76?)
check wiring and signals (sinking/sourcing, pulse width)
check reset input status
check parameters (use Data View)
Presets dont do anything
check preset values (BCD, correct addresses)
check interrupt routine (int #0, enabled at start, int
rtn at end of ladder)
check special relay numbers
Counts, but wont reset
check reset input or internal reset logic
Mode 20 Quadrature Counter
Mode 20
Must have an encoder that will work with
12-24VDC, or use external convertor
Mode 20 Configuration
Mode 20 Logic
SP1

You might also like