METHOD STATEMENT

HIGH STRIAN DYNAMIC TESTING OF PILE

Prepared by

Infratech ASTM CO., LTD.


Contents

Chapter Description Page



Contents ........... 1
List of Appendix .1

1. Introduction ..2
2. Test Method ..2
3. Test Equipment ...2



1
Infratech ASTM CO., LTD.




List of Appendix




Appendix A Test equipment















































2
Infratech ASTM CO., LTD.

1.0 INTRODUCTION
Dynamic load testing (DLT) of piles is a fast and effective method of assessing foundation bearing
capacity that requires instrumenting a deep foundation with accelerometers and strain transducers and
analyzing data collected by these sensors.
The procedure is based on the case method of pile testing and is standardized by ASTM D4945-00
Standard Test Method for High Strain Dynamic Testing of Piles. It may be performed on driven piles,
drilled shafts and other cast in place foundations. In addition to bearing capacity, Dynamic Load Testing
gives information on resistance distribution (shaft resistance and end bearing) and evaluates the shape
and integrity of the foundation element.
The foundation bearing capacity results obtained with dynamic load tests correlate well with the results
of static load tests performed on the same foundation element.



2.0 TEST METHOD
Adequate time should be allowed for soil stabilization before testing

Dynamic load testing (DLT) is carried out with two identical bolt-on strain and acceleration
transducers (sensor) attached to a section of pile.



3
Infratech ASTM CO., LTD.

On concrete pile, the sensors are connected to the pile with anchor bolts. On steel pile,
the sensors are bolted to the pile using threaded holes or welded mounting block.



The pile is then struck with a driving hammer or a separate drop weight. A hammer
mass of about 1 to 2% of the test load is generally sufficient. The generated compressive stress
wave travels down the piles and reflects from the pile toe upward. The stress waves, which are
picked up by the transducers, are processed and automatically stored in the computer for further
analysis and reporting.

The analysis is carried out using the signal matching program CAPWAP. Pile and soil data are
modeled and a response is calculated based on one dimensional wave equation theory. The signal
matching process utilizes an iterative method in which the results of each analysis are compared to the
actual measured pile behavior. Appropriate dynamic soil parameters are refined until a satisfactory
match is achieved. The mobilized static shaft and toe resistance of the pile can hence be derived. The
signal matching program also provides a prediction of the static load displacement performance of the
pile on the basis of the refined pile and soil model.


3.0 EQUIPMENT DETAILS
The pile driving analyzer (PDA) from PDI or SIMBAT MCSCO will be used for the test.
Details of test equipment have been shown in Appendix A.









4
Appendix A
Equipment Detail



HOME > Equipment > SIMBAT

SIMBAT

(Misung C&S Inspection co., Ltd.) is one of the professional indexed institutes of the exact
safely diagnosis in Korea, which was duly designated by the ministry of Constructio &
Transportation.

Product information
Name SIMBAT (Simulation Battage Tester)
Brand MCSCO
Model 01-006-2005-01
Product keyword SIMBAT, DYNAMIC REACTION, STATIC REACTION, PERMANENT SETTLEMENT
Image


Product explanation(use/characteristic/merit)
Usage

The SIMBAT tests are research of soils elastic reaction, joint-film reaction,
destructive reaction, and destructive adhesion reaction, that is, soil
parameter research, and were developed to predict the change from
dynamic reaction to static reaction through the test, comparing static and
dynamic loading capacity with the change of various soils in many model
piles, actually.

SIMBAT method was used pile loading tests of all rail road of T.G.V.
SIMBAT is newest method ended the error range of of USAs ASTM D4945
(American Standard Test Method)
The method is widely used in the worldwide including USA and Europe.
This method offers considerable advantages in term of speed and cost.
SIMBAT method is perfect to obtain the pile carrying capacity and very useful
method can be used widely.


The method for using Dr. Smiths wave equation also was starting to come
out problems, this formula, namely, the method used by substituting drop
hammering formula for bearing capacity is not difficult in application of the
simple P.C, PHC pile, etc., but it has big problems as the possibility of the
trust on large diameter cast-in-place pile of the big unit square measure
developed these days and foundation body including various soil.

Namely, it is difficult to understand the loading test accurately as the falling
wave velocity into the pile by established accelerator meter or pile and as the
measured deforcement ratio by strain gauge. This method is possible for the
certain investigation in falling compressive wave, but not in rising elastic
wave.

Move and more the numerical value of the rising elastic wave is different by
the pile mobility of side friction from the reaction of soil, the distribution of
the rising and falling wave from many experimentations is applied in the
formula of wave transmit distribution on back pile. The value of the side
friction mobility of pile, the value of displacement of different soil each
Page 1of 2 SIMBAT - Misung C&S Inspection
7/10/2553 http://www.mcsco.co.kr/English/Equipment/SIMBAT.asp
other, the value of dynamic displacement of ground, namely, Rdy = F (free
rising pile) - F (real pile) is got all from the real pile experimentation of
100's. And for making the possibility of trust high, another instrument,
namely, as composing strain location by the electric theodolite possible 10-
4 measured with the accelerated meter, removes errors of rising, falling
velocity caused by various soil.
Characteristic
* Prediction of static load settlement with efficient cost
* Theodolite makes the acceleration error correct.
(Acquiring reliance of dynamic load test)
* Measurement of elastic settlement
* Conversion the measurement of elastic settlement into prediction of
static load settlement
* Calculating soil reaction
* Capturing the friction of pile
* Prediction of pile load value by processing of data carried on site
* Exclusive analysis program

Equipment Spec
Equipment Spec.
* Enclosure : Overall dimensions 380X130X300mm, Unit weight 5kg
* Acquisition
3 channel, 12 bit acquisition at 50 KHz sampling rate
Pre-trigger on each channels, force, acceleration, displacement
User adjustable gain
* Sensors
2 Accelerometers as the resolution of 1mV/G
2 strain gauges for force measurement
* THEODOLITE
Measuring distance: 10 m
Measuring span: 400 mm
Resolution: 100 m
Band pass: 20 KHz
Required power: 65W From DC 12V
* Others
Exclusive notebook PC
2 sets of DC 12V adaptor
Case to carry and protect the whole equipment
Elevation tripod for theodolite
Analysis software
User's manual

Page 2of 2 SIMBAT - Misung C&S Inspection
7/10/2553 http://www.mcsco.co.kr/English/Equipment/SIMBAT.asp