System

Operating manual
STYLISTIC Q550
Congratulations, you have decided to buy an
innovative Fujitsu product.
The latest information about our products, useful tips, updates etc. is available
from our website: "http://ts.fujitsu.com"
For automatic driver updates, go to: "http://support.ts.fujitsu.com/com/support/index.html"
Should you have any technical questions, please contact:
our Hotline/Service Desk (see Service Desk list or visit:
"http://ts.fujitsu.com/support/servicedesk.html")
Your sales partner
Your sales ofce
We hope you really enjoy using your new Fujitsu system.
Copyright
Fujitsu Technology Solutions 2011 04/11
Published by
Fujitsu Technology Solutions
Mies-van-der-Rohe-Strae 8 (Mies-van-der-Rohe Street No. 8)
80807 Munich, Germany
Contact
http://ts.fujitsu.com/support
All rights reserved, including intellectual property rights. Subject to technical alterations. Delivery subject to availability.
No warranty is offered or liability accepted in regard of the completeness, correctness, or current applicability of any
data or illustrations. Brand names may be protected trademarks of the respective manufacturer and/or protected
by copyright. Use of these by third parties for their own purposes may constitute an infringement of the holders
rights. Further information can be found at "http://ts.fujitsu.com/terms_of_use.html"
Order No. Fujitsu Technology Solutions GmbH: A26391-K330-Z320-1-7619, edition 1
STYLISTIC Q550
Operating manual
Innovative technology 7
Ports and controls 9
Important notes 11
First-time setup of your device 17
Working with the Tablet PC 20
Security functions 53
Connecting external devices 60
Settings in BIOS Setup Utility 64
Troubleshooting and tips 67
Technical data 75
Manufacturers notes 77
Index 84
Microsoft, MS and Windows are registered trademarks of the Microsoft Corporation.
Adobe Reader is a trademark of Adobe Systems Incorporated.
MultiMediaCard is a registered trademark of Inneon Technologies AG
Sony and Memory Stick are registered trademarks of Sony Electronics, Inc.
All other trademarks referenced are trademarks or registered trademarks of their
respective owners, whose protected rights are acknowledged.
Copyright Fujitsu Technology Solutions GmbH 2011
All rights reserved, including rights of translation, reproduction by printing, copying
or similar methods, in part or in whole.
In the event of violations, perpetrators will be liable to prosecution for damages.
All rights reserved, including rights created by patent grant or registration of a utility model or design.
Subject to availability and technical modications.
Contents
Contents
Innovative technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Further information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Notational conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ports and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Safety notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Additional safety notes for devices with radio components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Protecting the display screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Energy saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Energy saving under Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Travelling with your Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Before you travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Transporting the Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning the Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
First-time setup of your device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Unpacking and checking the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Selecting a location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Mains adapter connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Switching on the device for the rst time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Working with the Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Switching on the Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Programming the ON/OFF switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Switching off the Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Handwriting recognition under Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Select display orientation (portrait or landscape orientation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using ngers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Calibrate the Dual Digitizer for nger-based operation of the device. . . . . . . . . . . . . . . . . . . . . . 23
Actions with one nger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Actions with two ngers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Actions with three ngers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Actions with four ngers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the stylus pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Setting the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Calibrating the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Changing the pen tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Removing the pen battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing a pen battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing a pen cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Tablet buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Programming the tablet buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Webcam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Rechargeable battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Charging, caring for and maintaining the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Removing and installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Using the power-management features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Memory cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Fujitsu Technology Solutions 3
Contents
Supported format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Inserting the memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Removing the memory card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Inserting the SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Removing a SIM card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Wireless LAN / Bluetooth / UMTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Switching the wireless components on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setting up WLAN access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Access via UMTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Your Cradle (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Cradle components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Setting up the Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Connecting the Tablet PC to the Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Disconnecting the Tablet PC from the Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Security functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Conguring the ngerprint sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Conguring password protection in BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Protecting BIOS Setup Utility (supervisor and user password) . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Password protection for booting of the operating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Password protection for the hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
SmartCard reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Inserting the SmartCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Trusted Platform Module (TPM) (device-dependent) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Enabling TPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Disabling TPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Connecting external devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
HDMI port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Connecting USB devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
How to remove USB devices correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Headphone port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Settings in BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Starting the BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Operating BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Exiting BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Exit Saving Changes - save changes and exit BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . 66
Exit Discarding Changes Discard changes and exit BIOS Setup Utility . . . . . . . . . . . . . . . . . 66
Load Setup Defaults Copy Standard Entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Discard Changes Discard changes without exiting the BIOS Setup Utility . . . . . . . . . . . . . . . 66
Save Changes - save changes without exiting the BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . 66
Save Changes and Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Troubleshooting and tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Help if problems occur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
The Tablet PCs date or time is incorrect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Battery indicator does not illuminate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
The Tablet PCs touchscreen remains dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
The display on the Tablet PCs touchscreen is difcult to read. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
The external monitor remains blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
The external monitor is blank or the image is unstable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4 Fujitsu Technology Solutions
Contents
The cursor does not correctly follow the pen movements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Pen input not working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
The Tablet PC does not start after switch on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
The Tablet PC stops working . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
The printer does not print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
The radio connection to a network does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
The battery discharges too quickly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
SmartCard reader is not recognised. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
SmartCard PIN forgotten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
SmartCard lost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
User and/or supervisor SmartCard lost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Acoustic warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Error messages on the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Tablet PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Rechargeable battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Mains adapter (40 W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Cradle (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Manufacturers notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Disposal and recycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Declarations of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Tested safety (TS, depending on the device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Regulatory notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Regulatory information for Tablet PCs without radio device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
DOC (Industry CANADA) notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
FCC Regulatory information for Tablet PCs with radio device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Fujitsu Technology Solutions 5
Contents
6 Fujitsu Technology Solutions
Innovative technology
Innovative technology
... and ergonomic design make your device a reliable and convenient companion.
The device boots very quickly, is ready for immediate use and offers a particularly
long operating time because of its high capacity battery.
The user-friendly "BIOS Setup Utility" offers powerful password protection functions which can be
used to control your Tablet PCs hardware and protect your system better against unauthorised use.
Information on the connections and controls for your Tablet PC can be
found in chapter "Ports and controls", Page 9.
Further information
The Windows drivers for your device can be found on our Internet site.
The factory installation of your device does not support any other operating
system. Fujitsu Technology Solutions accepts no liability whatsoever
if any other operating system is used.
Software oriented components of these instructions refer to Microsoft products,
if they come within the scope of the delivery.
If you install other software products, pay attention to the operating
instructions of the manufacturer.
Fujitsu Technology Solutions 7
Innovative technology
Notational conventions
Pay particular attention to text marked with this symbol. Failure to observe
these warnings could pose a risk to health, damage the device or lead
to loss of data. The warranty will be invalidated if the device becomes
defective through failure to observe these warnings.
Indicates important information for the proper use of the device.
Indicates an activity that must be performed

Indicates a result
This font
indicates data entered using the keyboard in a program dialogue or at
the command line, e.g. your password (Name123) or a command used to
start a program (start.exe)
This font
indicates information that is displayed on the screen by a program, e.g.:
Installation is complete.
This font Indicates
terms and texts used in a software interface, e.g.: Click on Save
names of programs or les, e.g. Windows or setup.exe.
"This font" Indicates
cross-references to another section, e.g. "Safety information"
cross-references to an external source, e.g. a web address: For more
information, go to "http://ts.fujitsu.com"
Names of CDs, DVDs and titles or designations for other materials,
e.g.: "CD/DVD Drivers & Utilities" or "Safety/Regulations" manual
Key
indicates a key on the keyboard, e.g:
F10
This font indicates terms and texts that are emphasised or highlighted, e.g.: Do
not switch off the device
8 Fujitsu Technology Solutions
Ports and controls
Ports and controls
This chapter presents the individual hardware components of your device. It gives you
an overview of the devices indicators and connections. Please familiarise yourself with
these components before you start to work with the device.
Front
1
2
3
4
5
6
7
8
9
10
1 = WebCam
2 = Eyelet for pen cord
3 = ON/OFF switch for wireless components
4 = Tablet button "Alt"
(function
Ctrl
+
Alt
+
Del)
function
5 = Tablet button "Change the screen
orientation"
6 = Tablet button "Keyboard"
7 = ON/OFF switch
8 = Status indicators
9 = DC input connector (DC IN)
10 = Port for Cradle
Fujitsu Technology Solutions 9
Ports and controls
Rear
1
3
4
5
6
7
2
8
8
1 = Battery compartment
2 = WebCam
3 = Memory card slot
4 = Fingerprint sensor
5 = USB port
6 = Headphone port
7 = HDMI port
8 = Microphones
10 Fujitsu Technology Solutions
Important notes
Important notes
Important notes Notes
This chapter contains essential safety information which must be followed when working
with your Tablet PC. The other notes provide useful information on your Tablet PC.
Safety notes
Safetynotes Notes
Please follow the safety notes provided in the "Safety/Regulations" manual
as well as the safety notes given below.
Please pay special attention to the sections in the manual marked
with the symbol on the left.
When connecting and disconnecting cables, observe the relevant
notes in this operating manual.
Read the information on the ambient conditions in the "Technical data", Page 75chapter
and the "First-time setup of your device", Page 17chapter before preparing your
Tablet PC for use and switching it on for the rst time.
When cleaning the device, please observe the relevant notes in the
section "Cleaning the Tablet PC", Page 16.
Pay attention to the additional safety notes for devices with radio components
provided in the "Safety/Regulations" manual.
This Tablet PC complies with the relevant safety regulations for data processing equipment.
If you have questions as to whether you can set up the Tablet PC in the intended
environment, please contact your sales point or our hotline/help desk.
Additional safety notes for devices with
radio components
Radiocomponent: WirelessLAN: Bluetooth, safetynotes
If a radio component (Wireless LAN/ Bluetooth) is integrated in your Tablet PC, you must be
sure to observe the following safety precautions when using your Tablet PC:
Switch off the radio components when you are in an aircraft or driving in a car.
Switch off the radio components when you are in a hospital, an operating room or near a medical
electronics system. The transmitted radio waves can impair the operation of medical devices.
Switch off the radio components when you let the device get near ammable
gases or into hazardous environments (e.g. petrol station, paintshops), as the
transmitted radio waves can cause an explosion or a re.
For information on how to switch radio components on and off, see chapter
"Switching the wireless components on and off", Page 47.
Fujitsu Technology Solutions 11
Important notes
Protecting the display screen
The device is not waterproof. Do not pour liquids on the system or wash it with a heavily
soaked cloth. Do not place items on the top of the display, or damage may occur.
During normal use of the device, small particles from the environment can
become embedded in the pen tip and scratch the screen. To prevent scratching
the screen, ensure that a screen protector is installed before using your
device. The warranty does not cover a scratched screen.
You device is designed for a long period of use. Using a screen protector will help ensure that
the screen remains as clear as possible. When installed, the screen protector becomes a
durable, replaceable writing surface that protects the display screen from abrasion.
The screen protector is held onto the display screen surface by a thin strip of adhesive
around the edges. There is a angled corner in one corner of the screen protector. It allows
you to slide your ngernail under the screen protector for easy removal.
Please contact your dealer for additional screen protectors.
Proceed as follows to attach a screen protector:
If a screen protector is already installed on the display screen, remove it
before installing the new screen protector.
Remove the protective coating from the adhesive side of the screen protector.
12 Fujitsu Technology Solutions
Important notes
Align the screen protector on the edges of the screen as illustrated and lay it
on the screen with the adhesive side downward.
Make stroking movements towards the outside edges in order to remove any air bubbles.
Press the edges rmly.
Fujitsu Technology Solutions 13
Important notes
To ensure a good seal between the screen protector and the display, do not lift
the screen protector from the display once it has been applied.
Carefully lift the plastic protective coating at the angled corner and pull it from the screen.

You can now touch the screen with the pen.

To remove all adhesive residue and prevent the tip of the pen from squeaking,
wipe the screen protector with a soft, dry cloth.
The adhesive sets completely within 48 hours.
14 Fujitsu Technology Solutions
Important notes
Energy saving
Notes Energy Energysaving
If you will not be using your Tablet PC, switch it off. Switch off any connected external devices
when they are not in use. If you use the energy saving functions, the Tablet PC uses less
power. You will then be able to work for longer before having to recharge the battery.
Energy efciency is increased and the environmental impact is reduced.
You save money while protecting the environment.
Energy saving under Windows
Make use of the power management features (see ""Using the power-management features",
Page 43").
Travelling with your Tablet PC
Mobileoperation Notes Transportation TabletPC
Please observe the points listed below when travelling with your Tablet PC.
Before you travel
Back up important data stored on your hard disk.
Tablet PC Travel,Tablet PC
Switch off the radio component for data security reasons. With data trafc via a wireless
connection, it is also possible for unauthorised third parties to receive data.
Information on activating data encryption is provided in the documentation
for your radio component.
If you want to use your Tablet PC during a ight, rst check with the ight
attendants whether this is permissible.
When travelling in other countries
If you are travelling abroad, check that the mains adapter can be operated with the
local mains voltage. If this is not the case, obtain the appropriate mains adapter
for your Tablet PC. Do not use any other voltage converter!
Check whether the local mains voltage and the power cable are compatible. If this is
not the case, buy a power cable that matches the local conditions.
Enquire with the corresponding government ofce of the country you will be
travelling in as to whether you may operate the radio component integrated in
your Tablet PC there (also see "CE marking", Page 78).
Fujitsu Technology Solutions 15
Important notes
Transporting the Tablet PC
Protect the Tablet PC from severe shocks and extreme temperatures
(e.g., direct sunlight in a car).
If your device has an optical drive, remove all data media (e.g. CD, DVD) from the drives.
Transportation Tablet PC
Switch off the Tablet PC.
Unplug the mains adapter and all external devices from the power socket.
Disconnect the mains adapter cable and the data cables for all external devices.
To protect against damaging jolts and bumps, use a Tablet PC carrying
case to transport your Tablet PC.
Cleaning the Tablet PC
Do not clean any interior parts yourself; leave this job to a service technician.
Only use cleaning products designed for computers. Normal household
cleaners and polishes can damage the markings on the keyboard and the
Tablet, the paintwork or the Tablet PC itself.
Please ensure that no liquid enters the Tablet PC.
The touchscreen is very sensitive to scratches! Only clean the display
surface with a very soft, slightly damp cloth.
Switch the Tablet PC off.
Cleaning Notes Tablet PC Keyboard Touchpad Touchscreen Crystal Viewdisplay
In order to prevent accidentially switching the device on, remove the power cable from the mains
adaptor and remove the battery (see "Removing and installing the battery", Page 40).

The casing surfaces may be cleaned with a dry cloth. If particularly dirty, use a damp cloth that
has been dipped in water mixed with mild domestic detergent and then carefully wrung out.
16 Fujitsu Technology Solutions
First-time setup of your device
First-time setup of your device
First-timesetup Gettingstarted
Please read the chapter "Important notes", Page 11.
If your device is equipped with a Windows operating system, the necessary
hardware drivers and supplied software are already pre-installed.
Before you switch on the device for the rst time, connect it to the mains voltage
using the mains adapter, see "Mains adapter connecting", Page 18. The mains
adapter must be connected during the entire installation process.
A system test is performed when your device is rst switched on. Various messages
can appear. The display may remain dark for a short time or may icker.
Please follow the instructions on the screen.
NEVER switch off your device during the rst-time setup process.
On delivery, the battery can be found in the battery compartment or in the accessories kit.
The battery must be charged if you want to operate your device using the battery.
When used on the move, the built-in battery provides the device with the necessary power. You
can increase the operating time by using the available energy-saving functions.
For instructions on how to connect external devices (e.g. mouse, printer) to your
device, please refer to the operating manual for your device.
Unpacking and checking the device
Should you discover any damage that occurred during transportation,
notify your local sales outlet immediately!
Unpack all the individual parts.
Packaging Transport
Check your device for any visible damage which may have occurred during transportation.
You may need the packaging in the future, if you need to transport your device.
Fujitsu Technology Solutions 17
First-time setup of your device
Selecting a location
Selectingalocation Device Mainsadapter
Select a suitable location for the device before setting it up. Follow
the instructions below when doing so:
Never place the device or the mains adapter on a heat-sensitive surface.
The surface could be damaged as a result.
Never place the device on a soft surface (e.g. carpeting, upholstered furniture,
bed). This can block the air vents and cause overheating and damage.
The underside of the device heats up during normal operation. Prolonged contact
with the skin may become unpleasant or even result in burns.
Place the device on a stable, at, non-slippery surface. Please note that the
rubber feet of the device may mark certain types of delicate surfaces.
Keep other objects at least 100 mm away from the device and its
mains adapter to ensure adequate ventilation.
Never cover the ventilation slots of the device.
Do not expose the device to extreme environmental conditions. Protect
the device from dust, humidity, and heat.
Mains adapter connecting
Preparingforoperation Mainsadapter
Observe the safety notes in the enclosed "Safety/Regulations" manual.
The supplied power cable conforms to the requirements of the country in
which you purchased your device. Make sure that the power cable is approved
for use in the country in which you intend to use it.
3
1
2
Connect the power cable (1) to the
mains adapter.
Plug the mains cable (2) into a mains outlet.
Connect the mains adapter cable (3) to
the DC jack (DC IN) of the device.
18 Fujitsu Technology Solutions
First-time setup of your device
Switching on the device for the rst time
Switchingonfor therst time
On devices with ON/OFF switch for wireless components: Slide the ON/OFF switch
for wireless components to the ON position before switching on the device.
When you switch on the device for the rst time, the supplied software is
installed and congured. Because this procedure must not be interrupted,
you should set aside enough time for it to be fully completed and connect
the device to the mains using the mains adapter.
During the installation process, DO NOT restart the device unless
you are requested to do so!
To make it easier to use your device for the rst time, the operating system
is pre-installed on the hard disk.
1
2
Slide the ON/OFF switch (1) to the right to switch on the Tablet PC.

The ON/OFF switch returns automatically to its original position.

The power-on indicator (2) lights up whenever the system is switched on.
During installation, follow the instructions on screen.
If a Windows operating system is installed on your device, you will nd more
information on the system and drivers, help programmes, updates, manuals etc.
on the device or on the Internet at "http://ts.fujitsu.com/support".
Fujitsu Technology Solutions 19
Working with the Tablet PC
Working with the Tablet PC
TabletPC, operation TabletPC
This chapter describes the basics for operating your Tablet PC. You can nd instructions
on how to connect external devices (e.g. mouse, printer) to the Tablet PC in the
chapter "Connecting external devices", Page 60.
Please refer to the notes in "Important notes", Page 11.
Status indicators
Statusindicators Symbols
The status indicators provide information about the status of the power supply,
the drives and the keyboard functions etc.
Status displays Description
Power-on indicator
The indicator is illuminated: The Tablet PC is switched on.
The indicator is ashing: The Tablet PC is in sleep mode (Save-to-RAM).
The indicator is not illuminated: The Tablet PC is switched off or in
Save-to-Disk mode.
Battery charging indicator
The battery charging indicator shows whether a battery is installed and being
charged.
20 Fujitsu Technology Solutions
Working with the Tablet PC
Switching on the Tablet PC
TabletPC: switchingon Power-onindicator Suspend/Resumebutton
1
2
Slide the ON/OFF switch (1) to the right to switch on the Tablet PC.

The ON/OFF switch returns automatically to its original position.

The power-on indicator (2) lights up whenever the system is switched on.
Programming the ON/OFF switch
You can program the ON/OFF switch:
Operating system Menu
Windows 7 Start - (Settings) - Control Panel - System and
Security - Power Options
If you have assigned a password, you must enter this when requested to
do so, in order to start the operating system. Detailed information can be
found in the chapter "Security functions", Page 53.
Switching off the Tablet PC
TabletPC
Close all applications and then shut down the operating system (please
see the "Operating System Manual").
Slide the ON/OFF switch towards the right.

The ON/OFF switch returns automatically to its original position.

Fujitsu Technology Solutions 21
Working with the Tablet PC
Handwriting recognition under Windows 7
Handwriting recognition under Windows 7 currently supports the following languages:
English, German, French, Italian, Japanese, Korean, Chinese (traditional and simplied), Dutch,
Portuguese, Spanish, Brazilian, Norwegian (Bokml and Nynorsk), Swedish, Finnish, Danish,
Polish, Rumanian, Serbian (Cyrillic and Latin script), Catalan, Russian, Czech and Croatian.
Touchscreen
Touchscreen Notes
High-quality TFT displays are installed in Tablet PCs from Fujitsu Technology Solutions GmbH. For
technical reasons, TFT monitors are manufactured for a specic resolution. An optimal, clear
picture can only be ensured with the correct resolution intended for the relevant TFT monitor. A
monitor resolution which differs from the specication can result in an unclear picture.
The screen resolution of your Tablet PCs touchscreen is optimally set at the factory.
The standard of production techniques today cannot guarantee an absolutely fault-free screen
display. A few isolated constant lit or unlit pixels (picture elements) may be present. The maximum
permitted number of pixels faults is stipulated in the international standard ISO 9241-3 (Class II).
Example:
A monitor with a resolution of 1280 x 800 has 1280 x 800 = 1024000 pixels. Each pixel consists of
three subpixels (red, green and blue), so there are almost 3 million subpixels in total. According to
ISO 9241-3 (class II), a maximum of 2 light and 2 dark pixels and an additional 5 light or 10 dark
subpixels or a corresponding mix may be defective (1 light subpixel counts as 2 dark subpixels).
Pixel A pixel consists of 3 subpixels, normally red, green and
blue. A pixel is the smallest element that can be generated
by complete functionality of the display.
Subpixel A subpixel is a separately addressable internal structure
within a pixel that enhances the pixel function.
Cluster A cluster contains two or more defective pixels or
subpixels in a 5 x 5 pixel block.
Background lighting
TFT monitors are operated with background lighting. The luminosity of the
background lighting can decrease while the Tablet PC is in use. However, you
can set the brightness of your monitor individually.
Synchronising the display on the touchscreen and an external monitor
In Windows 7, you can switch between touchscreen and external monitor, if you open
Control Panel - Windows Mobility Center, section External Display.
22 Fujitsu Technology Solutions
Working with the Tablet PC
Select display orientation (portrait or
landscape orientation)
Landscapeorientation Portraitorientation Displayorientation
You can choose to use either portrait or landscape orientation for the display. Press the
Tablet button to switch between portrait and landscape orientation.
Windows 7
You can change these settings in the Fujitsu menu or under Start - (Settings -)
Control Panel - Hardware and Sound - Display - Settings.
Proles for operating with various different screen modes can be selected via
the Fujitsu Tablet Control option in the Fujitsu menu. These proles have preset
standard congurations that can be modied as desired.
These settings do not just affect the monitor settings on the Tablet PC, but
also any external monitors that may be connected.
Using ngers
You can execute certain commands by using your nger tip on the touchscreen of your device.
Everything which you can select or activate using your nger tip can also
be selected or activated using the stylus pen.
Calibrate the Dual Digitizer for nger-based
operation of the device.
Before operating the device for the rst time using the ngers, you must calibrate
it so that your nger tips are recognized as accurately as possible.
You must calibrate the device again as soon as you notice that the
variations are becoming greater.
Operating system Menu
Windows 7 To calibrate, call up the Hardware and Sound / Tablet PC Settings function
in the Control Panel. You need to calibrate both portrait and landscape
formats.
Fujitsu Technology Solutions 23
Working with the Tablet PC
Actions with one nger
Action Description
Selecting objects (click with the left mouse
button)
With your nger, tap once briey on the
object.
Starting programs (double-click with the left
mouse button)
With your nger, tap twice briey in quick
succssion on the program icon.
Moving objects/windows (drag with left mouse
button pressed, Drag & Drop)
Place a nger directly on the object/window,
hold the nger pressed against the
touchscreen and move the desired
object/window.
Opening a context menu (click with the right
mouse button)
Touch the desired item once with your nger
tip. Keep the nger tip pressed against the
touchscreen.
The context menu appears.
Moving the cursor Position one nger on the touchscreen and
move the nger in the desired direction.
24 Fujitsu Technology Solutions
Working with the Tablet PC
Actions with two ngers
Action Description
Scrolling
Position two ngers on the touchscreen.
Move your ngers upwards to scroll up.
or
Move your ngers downwards to scroll
down.
Rotating
Position the thumb on the touchscreen,
then turn the picture clockwise or
counter-clockwise using your index nger.
Fujitsu Technology Solutions 25
Working with the Tablet PC
Action Description
Increasing or decreasing the view
Position two ngers on the touchscreen and
move them apart to increase the view.
or
Position two ngers on the touchscreen and
move them together to decrease the view.
Blocking context-sensitive menus With two ngers, tap twice briey in quick
succession on the touchscreen.
26 Fujitsu Technology Solutions
Working with the Tablet PC
Actions with three ngers
Action Description
Maximising or minimising current window
Position three ngers on the touchscreen
and move them upwards to maximise the
window.
or
Position three ngers on the touchscreen
and move them downwards to minimise the
window.
Fujitsu Technology Solutions 27
Working with the Tablet PC
Action Description
Displaying and rotating current window in 3D
carousel layout
Tap the touchscreen with your three ngers
to display the 3D carousel.
Hold your ngertips pressed to change the
3D carousel layout.
Minimising all windows and displaying the
desktop
With three ngers, tap the touchscreen twice
briey in quick succession.
28 Fujitsu Technology Solutions
Working with the Tablet PC
Action Description
Scrolling through all open les in a program
Position three ngers on the touchscreen
and move them to the side (left or right) over
the touchscreen.
Displaying context menu and selecting entry
Position two ngers on the touchscreen.
A context menu is displayed on the screen.
With one nger on the other hand, tap on an
entry in the context menu.
The entry is selected.
Fujitsu Technology Solutions 29
Working with the Tablet PC
Actions with four ngers
Action Description
Displaying a menu with context-sensitive web
applications with one hand
You can select a word, sentence, paragraph or
an item
Tap briey on the touchscreen with four
ngers on one hand then lift your ngers
from the screen.
A menu with context-sensitive web applications
is displayed.
Displaying menu with context-sensitive web
applications with two hands
To select an area, position two ngers of
each hand in a rectangle on the touchscreen
as shown.
A menu with context-sensitive web applications
is displayed.
30 Fujitsu Technology Solutions
Working with the Tablet PC
Action Description
Enlarging the area
To magnify an area of a document, position
two ngers of each hand in a rectangle on
the touchscreen as shown.
The selected area will be magnied.
Place one nger on the touchscreen to
move the rectangle around the touchscreen
to magnify several areas.
Fujitsu Technology Solutions 31
Working with the Tablet PC
Action Description
Paging through (fast scrolling)
Position four ngers on the touchscreen and
move them upwards to scroll up.
or
Position four ngers on the touchscreen and
move them downwards to scroll down.
The distance you sweep your ngers indicates
how far you move up or down.
32 Fujitsu Technology Solutions
Working with the Tablet PC
Using the stylus pen
1
2
3
1 = pen tip
2 = pen button
3 = eyelet for pen cord
You can use the pen on your Tablet PC as an electronic writing implement to select items, and to
navigate through programs on it. Programs that support handwriting recognition also allow you to
write characters directly on the screen with the pen. You can also use the pen as a drawing tool.
The pen is retained securely in the pen slot. This ensures that the pen cannot be lost,
regardless of whether you use the Tablet PC or transport it while travelling. Always
replace the pen in its slot when you are not using it.
The Tablet PC is supplied with a pen cord which you can attach to the eyelets
on the pen and on the Tablet PC.
Use only the pen provided with your Tablet PC. Do not use substitutes that
were not designed for your Tablet PC. Replace the stylus tip if it is worn.
The warranty does not cover a scratched screen.
While writing, you should take care not to scratch the surface of the
display (e.g. with a wristwatch or bracelet).
Fujitsu Technology Solutions 33
Working with the Tablet PC
The Tablet PCs pen is an electronic instrument that can be damaged if
used improperly. Handle the pen with care.
The following list contains guidelines for proper pen handling:
Do not gesture with the pen.
Do not use the pen as a pointer.
Do not use the pen on surfaces other than the screen of the Tablet PC.
Do not try to turn the thumb grip on the pen. The thumb grip is used to
place the pen in its slot and to take it out of the slot.
Never store the pen with the tip bearing the weight of the pen (e.g. with the tip down
in a pen holder). If the pen is stored with the tip pointing down, this may have
an adverse effect on the pen mechanism (particularly under high temperatures).
In this case the pen tip may react as though it is constantly being pressed down.
To avoid damage, the pen should be stored in the pen slot when not in use.
The pen can be inuenced by electromagnetic elds (cursor quivers or
jumps). There may be a few areas on the screen where the cursor quivers
slightly in spite of pressing the pen down rmly.
The screen responds to entries made with the tip of the nger or the pen when the tip
of the nger or the pen is in direct contact with the screen.
You can use the pen to run all functions for which you would otherwise use a mouse.
The pen does not support erasing functions.
Handling Mouse Pen
Selecting menu
items
Click with the left-hand mouse button. Touch the menu entry with the pen tip.
Starting programs Double click with the left-hand mouse
button.
Briey touch the program icon twice
with the pen tip.
Moving an
object/window
Drag with the left-hand mouse button
held pressed.
Place the pen tip directly on the
object/window. Hold the pen tip
pressed against the screen. Move the
desired object/window.
Opening a context
menu
Click with the right-hand mouse
button.
Place the pen directly on the required
element and hold the pen pressed
against the screen.
Moving the cursor
-
Place the pen tip directly on the
screen.
Setting the pen
Operating system Menu
Windows 7 Under Hardware and Sound Pen and Input Devices in the Control Panel
you can change various settings for the pen (assignment and function of
the pen button).
34 Fujitsu Technology Solutions
Working with the Tablet PC
Calibrating the pen
Before using the pen for the rst time, you should calibrate it so that the cursor follows the
movements of the pen as accurately as possible. You should also always repeat the calibration
if the co-ordination between the pen and cursor movement deteriorates.
Operating system Menu
Windows 7 To calibrate, call up the Hardware and Sound / Tablet PC Settings function
in the Control Panel. You need to calibrate both portrait and landscape
formats.
Changing the pen tip
With use, the pen tip may become worn or may pick up foreign particles that can scratch the screen.
A damaged or worn tip may not move freely, causing unpredictable results when using the pen.
If these problems appear with your pen, you should change the pen tip.
Pull the pen tip from the pen.
Replace the pen tip with one of the
replacement tips that were supplied
your pen. Insert the pointed end of the
pen tip into the barrel and push it in
gently until it is in place.
Do not continue to use a tip which is worn or damaged.
Fujitsu Technology Solutions 35
Working with the Tablet PC
Removing the pen battery
Do not take off the pen tip to change the battery.
The pen contains one AAAA battery.
1
2
Unscrew and remove the cap from
the pen (1).
Pull the battery out of the pen (2).
Installing a pen battery
1
2
Insert the new battery in the pen (1).
Close the pen cap (2).
Installing a pen cord
You should attach the pen with a pen cord to prevent accidentally dropping or losing it.
Fasten the pen cord to the pen eyelet and to the eyelet on the Tablet PC.
36 Fujitsu Technology Solutions
Working with the Tablet PC
Tablet buttons
Your Tablet PC is tted with three multi-functional tablet keys. You can navigate on the screen with a
simple press of a button, call preset applications or ones that you have set yourself.
Basic functions before the device has booted
You can congure the functions in the table below yourself.
The TPM PPI (Physical Presence Interface) menu is available only
if your system has a TPM module.
The TPM PPI menu is displayed after the security condition for the TPM
running under Windows has been changed.
Key
Function, if the key is
pressed while booting
the system
Function in
application menu/boot
menu/BIOS setup
Function in TPM PPI
menu
F1 (application menu) High

F2 (BIOS setup) Low Yes
F12 (Boot menu) Input No
Fujitsu Technology Solutions 37
Working with the Tablet PC
Basic functions when the device has booted
Button Basic function
Log on to the system or open the Windows Task Manager
If you keep this tablet button pressed for two seconds, you can log back onto
the system again:
after system startup
after a system lock
when returning from power management
After log-on, pressing the tablet button for two seconds launches the Windows
Task Manager or - in the network - opens the security window.
Change screen orientation
When you press this tablet button, the orientation of the screen display
changes from portrait (vertical) to landscape (horizontal) or vice versa.
If you wish to use the Tablet PC as an eBook, you should use the portrait
orientation.
When accessing spreadsheets, you would more typically use a landscape
orientation.
Tap: Monitor keyboard
If you tap this tablet key, the monitor keyboard is displayed.
Hold down: Calls up the Fujitsu menu
If you hold this tablet key down, the TouchLauncher appears on your screen.
Use the TouchLauncher to run the installed programs.
When you press this tablet button and keep it held, the Fujitsu menu appears
on your screen. The Fujitsu Menu is used to change certain system settings.
Programming the tablet buttons
You can program the tablet buttons to open a specic application or execute
a specic function when pressed.
Proceed as follows:
In Control Panel, select the option to manage the settings for the tablet buttons and pen.
Follow the instructions on the screen and program the tablet buttons as you require.
38 Fujitsu Technology Solutions
Working with the Tablet PC
Webcam
Webcam
Your device has two WebCams: one on the front side of the device and one on the rear.
Depending on the software used, you can use your Webcam to take pictures,
record video clips or take part in web chats.
The picture quality depends on the lighting conditions and the software being used.
You can only operate the webcam with a particular application (e.g. an Internet telephony
program or a video conferencing program which supports a webcam).
When using the webcam the Tablet PC support must not wobble.
The webcam automatically adjusts itself to the current light level. For this reason
the touchscreen may icker while the light level is adjusted.
Further information on using the webcam and on the additional settings
which are possible for your webcam can be found in the help function
of the program which uses the webcam.
If you wish to carry out a function test with your webcam, you can use the
corresponding test software available at "http://ts.fujitsu.com/support/".
Rechargeable battery
Rechargeablebattery Battery Life,battery Rechargeablebattery Rechargeablebattery
For mobile use, the built-in battery provides the Tablet PC with the necessary power.
You can increase the life of the battery by caring for the battery properly. The average
battery life is around 500 charge/discharge cycles.
You can extend the battery life by taking advantage of the available energy saving functions.
Fujitsu Technology Solutions 39
Working with the Tablet PC
Charging, caring for and maintaining the battery
Battery Battery
The Tablet PC battery can only be charged when the ambient temperature
is between 5C and max. 35C.
You can charge the battery by connecting the Tablet PC to the mains adapter
(see "Mains adapter connecting", Page 18).
If the battery is running low you will hear a warning alarm. If you do not connect the mains adapter
within ve minutes of the warning alarm described above, your Tablet PC will switch off automatically.
monitoring the battery charging level
Battery Batterystatusmeter
Windows also has a "Battery status meter" in the taskbar for monitoring the battery capacity. When
you place the mouse pointer on the battery symbol, the system displays the battery status.
Battery storage
Battery Battery Self-discharge, battery Chargingcapacity, battery
Keep the battery pack between 0C and +30C. The lower the temperature at which
the batteries are stored, the lower the rate of self-discharge.
If you will be storing batteries for a longer period (longer than two months),
the battery charge level should be approx. 30 %. To prevent exhaustive
discharge which would permanently damage the battery, check the level
of charge of the battery at regular intervals.
To be able to make use of the optimal charging capacity of the batteries, the battery
should be completely discharged and then fully recharged.
If you do not use the batteries for long periods, remove them from the
Tablet PC. Never store the batteries in the device.
Removing and installing the battery
Only use batteries approved by Fujitsu Siemens Computers for your Tablet PC.
Never use force when tting or removing a battery.
Make sure that no foreign bodies get into the battery connections.
Never store a battery for longer periods in the discharged state. This
can make it impossible to recharge.
40 Fujitsu Technology Solutions
Working with the Tablet PC
Removing the battery
Please observe the safety information in chapter "Important notes", Page 11.
Remove the power plug from the mains outlet!
Switch the device off.
The device must not be in energy-saving mode.
Remove all the cables from the device.
Turn the device over and place it on a stable, at and clean surface. If necessary, lay an
anti-slip cloth on this surface to prevent the device from being scratched.
2
1
3
Slide the release button in the direction of the arrow (1).
Slide the release button in the direction of the arrow (2) and hold it in place.
Remove the battery from the battery compartment (3).
Fujitsu Technology Solutions 41
Working with the Tablet PC
Installing battery
3
2
1
Slide the release button in the direction of the arrow (1).
Slide the release button in the direction of the arrow (2) and hold it in place.
Push the battery into the battery compartment until you feel it engage (3).
42 Fujitsu Technology Solutions
Working with the Tablet PC
Using the power-management features
Power Power Battery
The Tablet PC uses less power when the power management features are enabled. You will
then be able to work longer when using the battery before having to recharge it.
Power efciency is increased and environmental pollution reduced. By
choosing the best power options, you can make signicant savings and
at the same time help protect the environment.
We recommend the following settings:
Function On external power On battery power
Turn off monitor After 10 minutes After 5 minutes
Turn off hard disk(s) After 15 minutes After 10 minutes
Energy saving (S3) After 20 minutes After 15 minutes
Hibernate mode (S4) After 1 hour After 30 minutes
Select the power management functions in your Control Panel.
Select the Screen Saver in your Control Panel.
or
Keep a nger pressed on the desktop. Congure the screensaver under Personalization -
Change screensaver.
If you need further information about an option, you can get help with most settings by
pressing the
?
symbol in the upper right of the screen to open the Microsoft Help.
When the Tablet PC is in power saving mode, you must remember the following:
During power saving mode, open les are held in the main memory
or in a swap le on the hard disk.
Never switch off the Tablet PC while it is in a power saving mode. If the built-in battery is
nearly at, close the open les and do not go into power saving mode.
If you do not intend to use your Tablet PC for a long period of time:
Exit the power saving mode if necessary via touching the screen or by switching on the
Tablet PC.
Close all opened programs and completely shut down the Tablet PC.
Fujitsu Technology Solutions 43
Working with the Tablet PC
Memory cards
Slot
Your Tablet PC is equipped with an integrated memory card reader.
Observe the manufacturers instructions when handling the memory cards.
Memorycard
Supported format
The memory card reader supports the following format:
Secure Digital (SD
TM
card)
Inserting the memory card
Carefully slide the memory card into the
slot. The label should be facing upward. Do
not apply excessive force, as otherwise the
delicate contact surfaces could be damaged.
Memorycard

Depending on the particular type

used, the memory card may protrude
slightly from the slot.
44 Fujitsu Technology Solutions
Working with the Tablet PC
Removing the memory card
Memorycard
In order to protect your data, always follow the correct procedure
for removing the card outlined below.
You can stop the memory card via the corresponding icon in the task bar:
Tap on the symbol.
Select the card you want to stop and remove.
Tap OK.

Wait for the dialogue box which tells you that it is now safe to remove the memory card.
1
2
On devices with card locking: Press
on the storage card (1).
Memorycard

The storage card is released and

can now be removed.
Pull the storage card out of the slot (2).
Fujitsu Technology Solutions 45
Working with the Tablet PC
SIM card
A SIM Card (Subscriber Identity Module) is a chip card which is inserted in a mobile telephone or
Tablet PC and, together with an integrated UMTS module, enables access to a mobile radio network.
When handling SIM cards, follow the instructions supplied by the provider.
Inserting the SIM card
Remove the battery, see Chapter "Removing the battery", Page 41.
1
Slide the SIM card into the slot (1) until
it engages, as shown in the battery
compartment. The notch shows to the
left, the chip to the bottom.
Install the battery again, see Chapter "Installing battery", Page 42.
Removing a SIM card
Remove the battery, see Chapter "Removing the battery", Page 41.
1
Press on the edge of the SIM card so that
it jumps up slightly out of the slot.
Pull the SIM card out of the slot in the
direction of the arrow (1).
Install the battery again, see Chapter "Installing battery", Page 42.
Wireless LAN / Bluetooth / UMTS
The installation of radio components not approved by Fujitsu Technology Solutions
will invalidate the certications issued for this device.
46 Fujitsu Technology Solutions
Working with the Tablet PC
Switching the wireless components on and off
Before switching on your device for the rst time, the on/off switch for
radio components must be in the "ON" position.
Slide the ON/OFF switch into the "ON" position to activate the radio components.
WirelessLAN WirelessLAN Bluetooth Bluetooth
or
Slide the ON/OFF switch to the "OFF" position to deactivate the radio components.
If you switch off the radio components, the wireless LAN transmission unit (antenna)
and, if present, the Bluetooth and UMTS module will also be switched off.
You can enable and disable the installed radio components individually
using the WirelessSelector programme
You can also deactivate the wireless components individually in the BIOS Setup.
For this to occur, you must either not have assigned a supervisor password or if a
supervisor password has been assigned, you must know this password.
Pay attention to the additional safety notes for devices with radio components
provided in the "Safety/Regulations" manual.
Details on using Wireless LAN can be found in the online help system
included in the Wireless LAN software.
You can nd more information on how to use Bluetooth on the CD you
received with your Bluetooth software.
You can obtain more information on UMTS from your service provider.
Fujitsu Technology Solutions 47
Working with the Tablet PC
Setting up WLAN access
Requirement: A WLAN must be available and you must have the
corresponding access information.
Information on conguring the WLAN access can be found in the
documentation for your operating system.
Access via UMTS
If you ordered an integrated UMTS module with your system, you can enjoy optimum
reception and maximum energy efciency without awkward cables or antennas. The
optional UMTS module is ready for use straight away.
If you did not order a UMTS module, you can purchase the accessories for UMTS reception
from your retailer or your Fujitsu Technology Solutions dealer.
You will nd information on establishing the connection with the UMTS network
in the documentation for the hardware used.
You can connect your device with the Internet via UMTS. To do this, use one
of the following types of connection:
a USB dongle (a USB stick with your mobile phone providers SIM card)
mobile end-device (e.g. mobile phone with Bluetooth or cable connection)
GPS
GPS
Whether or not your device has this function depends on the
selected device expansion stage.
If your device is equipped with an integrated GPS module, you can use your device as a
navigation system with the help of a corresponding software programme.
48 Fujitsu Technology Solutions
Working with the Tablet PC
Your Cradle (optional)
Your Cradle is a device that helps you to quickly connect your Tablet PC to your
peripheral devices, such as a printer, mouse, etc.
You only need to dock the Tablet PC in order to work with your peripheral devices.
Cradle components
Cradle Ports
1
2
2
3
2
2
4
1 = Connector on the Cradle for the docking
port of the Tablet PC
2 = USB ports
3 = DC input connector (DC IN)
4 = Unlocking lever
Fujitsu Technology Solutions 49
Working with the Tablet PC
Setting up the Cradle
Select a suitable location for the Cradle before setting it up. Follow
the instructions below when doing so:
Place the Cradle on a at, stable, nonslippery surface.
Never place the Cradle and the mains adapter on a heat-sensitive surface.
Do not expose the Cradle to extreme environmental conditions.
Protect the Cradle from dust, humidity and heat.
1
Press the release lever and unfold the Cradles stand from (1), until it engages in its nal position
Connecting the Tablet PC to the Cradle
If you connect the Tablet PC to the Cradle during operation, problems can occur.
We recommend that you switch off the Tablet PC beforehand.
If the Tablet PC is connected to the Cradle, you must connect the
mains adapter to the Cradle.
Cradle
Switch off the Tablet PC.
50 Fujitsu Technology Solutions
Working with the Tablet PC
Remove the power plug of the mains adapter from the mains socket.
Pull the mains adapter cable out of the DC jack (DC IN) of the Tablet PC.
1
2
4
3
Position the Tablet PC so that it is in line with the storage space of the Cradle.
Push the Tablet PC on to the Cradle in the direction of the arrow (1) until
you notice it engage with the plug.
Plug the DC output connector on the mains adapter into the DC input
connector (DC IN) on the Cradle (2).
Connect the power cable to the mains adapter (3).
Plug the power cable into the mains socket (4).
Close the clip on the rear side of the Cradle.
Fujitsu Technology Solutions 51
Working with the Tablet PC
Disconnecting the Tablet PC from the Cradle
If you connect the Tablet PC to the Cradle during operation, problems can
occur. We recommend that the Tablet PC is switched off or that the appropriate
undocking function provided by the operating system is executed.
Switch off the Tablet PC.
Open the clip on the rear side of the Cradle.
1
Lift the Tablet PC from the Cradle in the direction of the arrow (1), while
supporting the underneath of the Cradle.
52 Fujitsu Technology Solutions
Security functions
Security functions
Securityfunctions
Your Tablet PC has several security features that you can use to secure your
system from unauthorised access.
This chapter explains how to use each function, and what the benets are.
Please remember that in some cases, for example, forgetting your password,
you may be locked out and unable to access your data. Therefore,
please note the following information:
Make regular backups to external data carriers such as external hard
drives, CDs, DVDs or Blu-ray Discs.
Some security functions need you to choose passwords. Make a note
of the passwords and keep them in a safe place.
If you forget your passwords you will need to contact the our Service
Desk. Deletion or resetting of passwords is not covered by your warranty
and a charge will be made for assistance.
Conguring the ngerprint sensor
Fingerprintsensor Fingerprintsensor
The ngerprint sensor can record an image of a ngerprint. With additional ngerprint
software, this image can be processed and used instead of a password.
1
You must install the ngerprint software
in order to be able to use the
ngerprint sensor (1).
Fujitsu Technology Solutions 53
Security functions
Conguring password protection in BIOS Setup Utility
To navigate more easily in the BIOS Setup Utility, you can use an external USB keyboard.
Before using the various options for password protection in the BIOS Setup utility
to increase data security, please observe the following:
Make a note of the passwords and keep them in a safe place. If you forget your
supervisor password you will not be able to access your Tablet PC. Passwords are
not covered by your warranty and a charge will be made for assistance.
Passwordprotection
Your password can be up to eight characters long and contain letters and numbers.
No distinction is made between uppercase and lowercase.
Protecting BIOS Setup Utility (supervisor and user password)
If you have opened these operating instructions on the screen, we recommend that
you print out the following instructions. Because you cannot call the instructions
onto the screen while you are setting up the password.
BIOSSetupUtility
You prevent unauthorised use of the BIOS Setup Utility with both the supervisor and the user
password. The supervisor password gives you access to all functions of the BIOS Setup
Utility, while the user password only provides some of the functions. You can only set a
user password if a supervisor password has already been assigned.
Please refer to the ""Settings in BIOS Setup Utility", Page 64 section for a
description of how to call up and operate the BIOS Setup Utility.
54 Fujitsu Technology Solutions
Security functions
Setting supervisor and user password
Start the BIOS Setup Utility and go to the Security menu.
Select the Set Supervisor Password eld and press the Enter key.

With Enter new Password: you are asked to enter a password.

Enter the password and press the Enter key.

Conrm new Password requires you to conrm the password.

Enter the password again and press the Enter key.

Changes have been saved is a conrmation that the new password has been saved.
To set the user password, select Set User Password and proceed exactly as
when conguring the supervisor password.

If you do not want to change any other settings, you can exit BIOS Setup Utility.
In the Exit menu, select the option Save Changes & Exit.
Select Yes and press the Enter key.
Password Supervisor password Userpassword

The Tablet PC is rebooted and the new password is effective. It will now be necessary to
rst enter your supervisor or user password in order to open the BIOS Setup Utility. Please
note that the user password only provides access to a few of the BIOS settings.
Changing the supervisor or user password
You can only change the supervisor password when you have logged into the
BIOS Setup Utility with the supervisor password.
Password Supervisorpassword User password
Call the BIOS Setup Utility and go to the Security menu.
When changing the password, proceed exactly as for password assignment.
Removing passwords
To remove a password (without setting a new password) perform the following steps:
Password Supervisorpassword User password
Start the BIOS Setup Utility and go to the Security menu.
Highlight the Set Supervisor Password or Set User Password eld and press the Enter key.

You will be requested to enter the current password by the Enter Current Password prompt.
You will be requested to enter a new password by the Enter New Password prompt.
Press the Enter key twice.
In the Exit menu, select the option Save Changes & Exit.
Select Yes and press the Enter key.

The Tablet PC is rebooted and the password is cancelled.

Removing the supervisor password simultaneously deactivates the user password.
Password protection for booting of the operating system
With the supervisor password you have set in the BIOS Setup Utility (see
section "Setting supervisor and user password", Page 55), you can also
prevent booting of the operating system.
Operatingsystem
Fujitsu Technology Solutions 55
Security functions
Activating system protection
Start the BIOS Setup Utility and go to the Security menu.
Operatingsystem
Select the Password on Boot option and press the Enter key.
Select the desired option (Disabled, First Boot or Every Boot) and press the Enter key
Select the Save Changes & Exit option under Exit.

The Tablet PC reboots. You will be prompted to enter your password (the supervisor password).
Deactivating system protection
Start the BIOS Setup Utility and go to the Security menu.
Operatingsystem
Select the Password on Boot option and press the Enter key.
Select the Disabled option and press the Enter key.

If you do not want to change any other settings, you can exit BIOS Setup Utility.
Select the Save Changes & Exit option under Exit.

The Tablet PC reboots. The system is no longer password-protected.

Password protection for the hard disk
Passwordprotection:
The had disk password prevents unauthorised access to the hard disk drives
and is checked internally each time the system is booted. The condition for this
is that you have assigned at least the supervisor password.
Activating hard disk protection
Call up the BIOS Setup and select the Security menu.

If you have not assigned BIOS passwords yet, dene the supervisor and the user
password now, if desired (see "Security functions", Page 53).
Mark the Hard Disk Security eld and press the Enter key.
In the Drive0 area mark the Set Master Password eld and press the Enter key.

Enter new Password then appears and you are asked to enter a password.
Enter the password and press the Enter key.

Conrm new Password requires you to conrm the password.

Enter the password again and press the Enter key.

Setup Notice: Changes have been saved is displayed to conrm that the
new password has been saved.
To assign the password for the second hard disk (Drive1), go to the Drive1 area and
select the eld Set Master Password, then proceed in exactly the same way as for
setting up the password for the rst hard disk (Drive0).

The eld Password Entry on Boot is set to Enabled by default. You can exit the BIOS
Setup once you have nished changing the settings.
From the Exit menu, choose the option Exit Saving Changes.
Press the Enter key and select Yes.

The Table PC reboots and your hard disk is now protected with a password. The
password prompt is enabled as soon as the Tablet PC has rebooted.
56 Fujitsu Technology Solutions
Security functions
Deactivating hard disk protection
To cancel a password without setting a new one, proceed as follows:
Call up the BIOS Setup and select the Security menu.
Mark the Hard Disk Security eld and press the Enter key.
In the Drive0 area mark the Set Master Password eld and press the Enter key.

You will be initially requested to enter the old password by the Enter current Password prompt.
You will then be requested to enter a new password by the Enter new Password prompt.
After entering the password, press the Enter key three times.
From the Exit menu, choose the option Exit Saving Changes.
Press the Enter key and select Yes.

The Tablet PC reboots and there is no longer any password protection for this hard disk.
To cancel the password for the second hard disk (Drive1), go to the Drive1 area
and select the eld Set Master Password, then proceed in exactly the same way as
for cancelling the password for the rst hard disk (Drive0).
Fujitsu Technology Solutions 57
Security functions
SmartCard reader
Securityfunctions, Securityfunctions
SmartCards are not supplied as standard equipment. You can use all SmartCards that comply with
the ISO standard 7816-1, -2 or -3. These SmartCards are available from various manufacturers.
With the appropriate software you can use your SmartCard as an alternative to password protection,
but also as a digital signature, for encrypting your e-mails or for home banking.
We recommend that you always use two SmartCards. Always keep one of the SmartCards
in a safe place if you are carrying the other SmartCard with you.
In order to be able to take advantage of all the security features of your Tablet PC, you
will need a CardOS SmartCard from Fujitsu Technology Solutions.
The SmartCard can only be used with a PIN, offering maximum protection even if
you lose the SmartCard. In order to maximise your security, the CardOS SmartCard
is disabled if three incorrect attempts are made to enter the PIN.
When you use the CardOS SmartCard for the rst time, you will either need to enter the
preset PIN "12345678" or the PIN given to you by your systems administrator.
Inserting the SmartCard
Do not use force when inserting and removing the SmartCard.
Make sure that foreign objects do not fall into the SmartCard reader.
Slide the SmartCard into the SmartCard reader with the chip facing upwards
(on some variants it faces down) and to the front.
58 Fujitsu Technology Solutions
Security functions
Trusted Platform Module (TPM) (device-dependent)
TPM TrustedPlatformModule
To use the TPM, you must activate the TPM in the BIOS Setup before the software
is installed. The condition for this is that you have assigned at least the supervisor
password (see "Security functions", Page 53).
Enabling TPM
Requirement: You have assigned a supervisor password, see "Security functions", Page 53.
Call up the BIOS Setup and select the Security menu.
Mark the TPM Security Chip Setting eld and press the Enter key.
Select Enabled to activate the TPM.

Once you have activated the TPM the Clear Security Chip option appears.
Select Clear Security Chip to delete the holder in the TPM. By clicking on Enabled,
all secret keys (e.g. SRK - Storage Root Keys, AIK - Attestation Identity Keys
etc.) generated by applications are deleted.
Please note that you will then no longer be able to access the data you have
encrypted with the keys based on that holder.
Select the Exit Saving Changes option in the Exit menu.
Press the Enter key and select Yes.

The Tablet PC restarts and the TPM is switched on after the reboot.
Disabling TPM
Requirement: You have assigned a supervisor password, see "Security functions", Page 53.
Call up the BIOS Setup and select the Security menu.
Mark the TPM Security Chip Setting eld and press the Enter key.
Select Disabled to deactivate the TPM.
From the Exit menu, choose the option Exit Saving Changes.
Press the Enter key and select Yes.

The Tablet PC is rebooted and the TPM is disabled.

Fujitsu Technology Solutions 59
Connecting external devices
Connecting external devices
Under all circumstances, please observe the safety notes provided in the
"Important notes", Page 11 chapter before connecting or disconnecting
any devices to or from your Tablet PC.
Always read the documentation supplied with the device you wish to connect.
Never connect or disconnect cables during a thunderstorm.
Never pull at a cable when disconnecting it. Always grasp the plug.
Adhere to the order described below when you connect external devices
to the Tablet PC or separate them from it:
With some devices, such as USB devices, it is not necessary to switch off
the Tablet PC and the device before connecting/disconnecting. For more
information about whether or not devices need to be switched off, please refer
to the documentation supplied with the external device.
Some of the external devices require special drivers (see the operating
system and external device documentation).
Connecting devices to the Tablet PC
1. Switch off the Tablet PC and all external devices.
2. Remove the mains plug for the Tablet PC and all relevant devices from the sockets.
3. Connect the cables for your external devices following the instructions.
4. Plug all power cables into the mains sockets.
Devices Peripheral devices
Disconnecting devices from the Tablet PC
1. Switch off the Tablet PC and all external devices.
2. Remove the mains plug for the Tablet PC and all relevant devices from the sockets.
3. Disconnect the cables for your external devices following the instructions.
Devices Peripheral devices
60 Fujitsu Technology Solutions
Connecting external devices
HDMI port
HDMIport
The HDMI port of your Tablet PC can be used to connect an external amplier,
LCD TV or a plasma TV with an HDMI connection.
Connect the data cable to the
external device.
Connect the data cable to the HDMI
port of the Tablet PC.
Some LCD televisions have only two loudspeaker connections and therefore
cannot reproduce Dolby digital or DTS. In order to reproduce the sound, you
must go into Windows and adjust the sound settings.
Proceed as follows:
Select Startsymbol (Settings) Control Panel Hardware and Sound Sound.
Mark Realtek HDMI Output.
Select Properties Supported formats.
Deactivate the settings DTS audio and Dolby digital.
Conrm the settings with OK.
Fujitsu Technology Solutions 61
Connecting external devices
Connecting USB devices
USBports
On the USB ports, you can connect external devices that also have a USB port
(e.g. a DVD drive, a printer, a scanner or a modem).
USB devices are hot-pluggable. This means you can connect and disconnect
devices while your operating system is running.
USB 2.0 has a data transfer rate of up to 480 Mbit/s.
Additional information can be found in the documentation for the USB devices.
Connect the data cable to the
external device.
Connect the data cable to the USB
port on the Tablet PC.
Device drivers
USB devices will be automatically recognised and installed by your operating system.
How to remove USB devices correctly
Always correctly remove the device according to the rules described below,
to ensure that none of your data is lost.
Tap the symbol for safe removal of the hardware.
Select the device which you want to shut down and remove.
Tap OK.

Wait for the dialogue box which tells you that it is now safe to remove the device.
62 Fujitsu Technology Solutions
Connecting external devices
Headphone port
Connectingaudiodevices Audioports Connectingheadphones
Via the headphone port, you can connect either a headphone or an external speaker to your Tablet PC.
Connect the audio cable to the
external device.
Connect the audio cable to the headphone
port of the Tablet PC.

The internal loudspeakers are disabled.

If you purchase a cable from a retailer, please note the following information:
The headphone port on your Tablet PC is a "3.5 mm jack socket".
If you want to connect headphones or a speaker you will need a "3.5 mm jack plug".
Fujitsu Technology Solutions 63
Settings in BIOS Setup Utility
Settings in BIOS Setup Utility
BIOSSetupUtility Systemsettings,BIOSSetupUtility Conguration, BIOSSetupUtility Setup Systemconguration Hardwareconguration
To navigate more easily in the BIOS Setup Utility, you can use an external USB keyboard.
The BIOS Setup Utility allows you to set the system functions and the hardware
conguration for the Tablet PC.
When it is delivered, the Tablet PC is set to factory default settings. You can
change these settings in BIOS Setup Utility. Any changes you make take effect as
soon as you save and exit the BIOS Setup Utility.
The BIOS Setup Utility program contains the following menus:
About Displays information relating to the BIOS, processor and Tablet PC
System Advanced system settings
Advanced Conguration of various hardware components, such as mouse, keyboard,
processor
Security Password settings and security functions
Boot Conguration of the start-up sequence
Exit Exits the BIOS Setup Utility
Starting the BIOS Setup Utility
Keep the "Change screen orientation" tablet button pressed and switch the Tablet PC on.
BIOSSetupUtility
If a password has been assigned, enter the password and press the Enter key.
If you have forgotten the password, contact your system administrator
or contact our customer service centre.
The BIOS Setup Utility starts.
64 Fujitsu Technology Solutions
Settings in BIOS Setup Utility
Operating BIOS Setup Utility
BIOSSetupUtility
Use the touchscreen to operate the function keys in the BIOS Setup Utility.
Tap on any element in the BIOS Setup menus or tap on the function or
cursor keys indicated on the bottom of the screen.
Press the
F1
key to display help on the operation of the BIOS Setup Utility. The description
of the individual settings is shown in the right-hand window of the BIOS Setup Utility.
With the
F9
key you can load the default settings of the BIOS Setup Utility.
Use the cursor keys

or

to select the menu you wish to access to make changes.

The menu is displayed on the screen.

Select the option you want to change with the cursor keys

or

.
Press the Enter key.
Press the
ESC
key to exit the selected menu.
For future reference, make a note of the changes you have made (for example, in this manual).
Fujitsu Technology Solutions 65
Settings in BIOS Setup Utility
Exiting BIOS Setup Utility
BIOSSetupUtility
You need to select the desired option in the Exit menu and activate it by pressing the Enter key:
Exit Saving Changes - save changes and exit BIOS Setup Utility
To save the current menu settings and exit the BIOS Setup Utility, select Exit Saving Changes and Yes.

The Tablet PC is rebooted and the new settings come into effect.
Exit Discarding Changes Discard changes and
exit BIOS Setup Utility
To discard the changes, select Exit Discarding Changes and Yes.

The settings in place when BIOS Setup Utility was called remain effective. The BIOS
Setup Utility is terminated and the Tablet PC is rebooted.
Load Setup Defaults Copy Standard Entries
To copy the standard entries for all menus of the BIOS Setup Utility,
choose Load Setup Defaults and Yes.
Discard Changes Discard changes without exiting
the BIOS Setup Utility
To discard the changes you have made, select Discard Changes and Yes.

The settings in place when BIOS Setup Utility was called remain effective.
You can now make additional settings in the BIOS Setup Utility.
If you want to exitBIOS Setup Utilitywith these settings, select Exit Saving Changes and Yes.
Save Changes - save changes without exiting
the BIOS Setup Utility
To save the changes, select Save Changes and Yes.

The changes are saved. You can now make additional settings in the BIOS Setup Utility.
If you want to exit BIOS Setup Utility with these settings, choose Exit Saving Changes and Yes.
Save Changes and Power Off
To save the changes and switch off your device, select Save Changes and Power Off and Yes.

The changes are saved. Your device is shut down.

66 Fujitsu Technology Solutions
Troubleshooting and tips
Troubleshooting and tips
Troubleshooting Tips Fault Troubleshooting
Follow the safety notes in the "Safety/Regulations" manual when
connecting or disconnecting cables.
If a fault occurs, try to correct it as described. If you fail to correct the problem, proceed as follows:
Make a note of the steps and the circumstances that led to the fault. Also
make a note of any error messages displayed.
Switch the Tablet PC off.
Please contact the Hotline/Service Desk.
You can nd the telephone numbers in the service desk list. Please have
the following information ready when you call:
The model name and serial number of the Tablet PC. The serial number
is located on a sticker on the underside of the Tablet PC.
Notes of any messages that appear on the screen and information on acoustic signals.
Any changes you have made to the hardware or software after
receiving the Tablet PC.
Any changes you have made to the BIOS Setup settings after receiving the Tablet PC.
Your system conguration and all peripheral devices connected to your system.
Your sales contract.
Our Tablet PCs have been designed primarily with mobile applications in mind. This
means that considerable effort has been made to optimise components and equipment
in terms of weight, space and energy requirements. Depending on the particular
conguration you have purchased, it is possible that functionality may be slightly reduced
compared to a desktop PC if you are running processor-intensive gaming software, e.g.
games with intensive 3D graphics. Updating your hardware with drivers which have not
been approved by Fujitsu Technology Solutions may result in performance losses, data
losses or malfunction of the equipment. A list of approved drivers and current BIOS
versions can be downloaded from: "http://ts.fujitsu.com/support/downloads.html"
Help if problems occur
Should you encounter a problem with your computer that you cannot resolve yourself:
Note the ID number of your device. The ID number is found on the type rating
plate on the back or underside of the casing.
For further clarication of the problem, contact the Help Desk for your country (see the Help
Desk list or visit the Internet at "http://ts.fujitsu.com/support/servicedesk.html"). When you
do this, please have ready the ID number and serial number of your system.
Fujitsu Technology Solutions 67
Troubleshooting and tips
The Tablet PCs date or time is incorrect
Summer time Time, daylightsavings Timenotcorrect Timenotcorrect Incorrect date/time Dateisincorrect Buffer battery,load
Cause Troubleshooting
Time and date are incorrect. With the BIOS-Setup-Utility, you can set the
date and time in the main menu.
Date and time are still set incorrectly after
switching on the Tablet PC.
Please contact your sales outlet or our
Hotline/Service Desk.
Battery indicator does not illuminate
Cause Fault elimination
The battery is not installed correctly. Switch the Tablet PC off.
Check whether the battery is installed
correctly in its compartment.
Switch the Tablet PC on.
The battery is fully discharged. Charge the battery.
or
Install a charged battery.
or
Connect the Tablet PC to a mains outlet
using the mains adapter.
The Tablet PCs touchscreen remains dark
Touchscreen touchscreenistoodark
Cause Troubleshooting
Touchscreen is switched off. Press a key (external keyboard) or tap on
the touchscreen.
External monitor or television set connected. Check whether the graphics driver settings
are correct or whether an external monitor
has been detected in "Intel Graphics Media
Accelerator Driver for mobile".
The display on the Tablet PCs touchscreen
is difcult to read.
Touchscreen Touchscreen
Cause Troubleshooting
Reected glare Move the Tablet PC into a different position.
Increase the brightness of the screen.
68 Fujitsu Technology Solutions
Troubleshooting and tips
The external monitor remains blank
Monitor
Cause Troubleshooting
Monitor is switched off. Switch the external monitor on.
Power saving has been activated (monitor is
blank).
Press a key (external keyboard) or tap on
the touchscreen.
Brightness is set to dark. Adjust the brightness of the monitor.
Screen output is set on the Tablet PCs
touchscreen.
Check whether the graphics driver settings
are correct or whether an external monitor
has been detected in "Intel Graphics Media
Accelerator Driver for mobile".
The external monitors power cable or data
cable is not connected properly.
Switch off the Tablet PC and the external
monitor.
Check whether the power cable is plugged
properly into the external monitor and into
the power socket.
Check whether the data cable is properly
connected to the Tablet PC and the external
monitor (if it is plugged in with a connector).
Switch on the Tablet PC and the external
monitor.
The external monitor is blank or the image is unstable
Screen Monitor
Cause Troubleshooting
The wrong external monitor has been selected
or the wrong screen resolution has been set for
the application program.
Terminate the application program in
Windows. If the error persists after
terminating the program, use the key
combination for switching the screen output
in order to switch to the touchscreen of the
Tablet PC. Change the following setting:
Set the screen resolution: Set the screen
resolution as described in the documentation
for your operating system.
Select monitor: Select monitor 1 or 2 as
described in the documentation for your
operating system.
Fujitsu Technology Solutions 69
Troubleshooting and tips
The cursor does not correctly follow the
pen movements
Cause Fault elimination
Pen incorrectly calibrated Calibrate the pen as shown under Hardware
and Sound / Tablet PC Settings in the Control
Panel, see "Setting the pen", Page 34 and
"Calibrating the pen", Page 35.
Pen input not working
Cause Troubleshooting
Incorrect driver installed. If your device is one which can only be
operated using the pen, install the driver for
the standard model.
or
If your device is one which can be
operated using the pen and by nger,
install the driver for the "Dual Digitizer"
model.
The Tablet PC does not start after switch on
TheTablet PC
Cause Troubleshooting
The battery is not installed correctly. Check whether the battery is installed
correctly in its compartment.
Switch on the Tablet PC.
The battery is dead. Charge the battery.
or
Insert a charged battery.
or
Connect the mains adapter to the Tablet
PC.
The power adapter is not connected correctly. Check whether the mains adapter is
connected correctly to the Tablet PC.
Switch on the Tablet PC.
70 Fujitsu Technology Solutions
Troubleshooting and tips
The Tablet PC stops working
TheTablet PC Energysavingmode
Cause Troubleshooting
The Tablet PC is in energy saving mode. Leave energy saving mode.
An application programme has caused the
malfunction.
Close the application program or restart
the Tablet PC (by restarting the operating
system or switching the device off and back
on again).
The battery is dead. Charge the battery.
or
Insert a charged battery.
or
Connect the mains adapter to the Tablet
PC.
The printer does not print
Printer doesnot print
Cause Troubleshooting
The printer is not switched on. Make sure that the printer is switched
on and ready for operation (refer to the
documentation supplied with the printer).
The printer is not connected correctly. Check that the data cable connecting
the Table PC to the printer is properly
connected.
The printer driver is faulty or not correctly
installed, or it is the wrong printer driver.
Check that the data cable connecting
the Tablet PC to the printer is properly
connected.
Check whether the correct printer driver is
loaded (refer to the printer documentation).
The radio connection to a network does not work
Theradioconnectiontoanetworkdoesnot work
Cause Troubleshooting
The wireless component is disabled. Switch the radio component on (see
"Switching the wireless components on and
off", Page 47).
The wireless component is enabled. Despite
this, the wireless connection to a network does
not work.
Check whether the radio connection is
switched on via the software.
Further information on using the radio
component can be found in the help les.
Fujitsu Technology Solutions 71
Troubleshooting and tips
The battery discharges too quickly
Battery:
Cause Troubleshooting
The battery is either too hot or too cold. In this
case the battery indicator ashes.
Bring the Tablet PC up/down to a normal
temperature again.
If the operating time of the battery life is
extremely short, the battery is probably too
old. Replace battery if necessary.
You may have an application running that
consumes a great deal of power due to frequent
accessing of the hard disk or optical drive.
Use the mains adapter as frequently as
possible.
The maximum brightness may have been set
for the screen.
Reduce the brightness of the screen to
lower energy consumption: You will nd the
setting under Control Panel Hardware and
Sounds Windows Mobility Center.
SmartCard reader is not recognised.
Cause Troubleshooting
Chip card inserted incorrectly. Make sure you have inserted your
SmartCard into the SmartCard reader with
the chip facing upwards.
Check whether the SmartCard you are using
is supported. Your SmartCard must comply
with the ISO standard 7816-1, -2, -3 and -4.
SmartCard PIN forgotten
Cause Troubleshooting
PIN forgotten If you work in a network, contact your
system administrator, who can unlock your
Tablet PC with a supervisor PIN.
SmartCard lost
Cause Troubleshooting
SmartCard lost If you work in a network, contact your
system administrator, who can boot your
Tablet PC with a Supervisor SmartCard.
72 Fujitsu Technology Solutions
Troubleshooting and tips
User and/or supervisor SmartCard lost
Cause Troubleshooting
User and/or supervisor SmartCard lost If you have lost your User SmartCard, you
can continue working with the Supervisor
SmartCard and initialise a new User
SmartCard or deactivate the SystemLock
function.
If you have lost the Supervisor SmartCard,
you can continue working, but you no longer
have all your rights and can no longer
initialise a Supervisor SmartCard.
If you have lost both SmartCards, you can
no longer boot your system. Please contact
our Service Desk. You must provide proof of
ownership for the device. Then the Service
Desk will refer you to our service partner,
who will unlock your device (for a charge).
Acoustic warnings
Acousticerror messages Errors
Cause Troubleshooting
A beep sounds every few seconds.
The battery is almost at.
Charge the battery.
Error messages on the screen
Error messagesonthescreen Error message:
This section describes the error messages generated by the BIOS Setup. Error messages displayed
by the operating system or programmes are described in the relevant documentation.
If the error message appears repeatedly, despite troubleshooting measures, please
contact the place of purchase or our customer service centre.
Fujitsu Technology Solutions 73
Troubleshooting and tips
Error message/cause Resolution
CMOS battery bad
If the error message occurs repeatedly, the
buffer battery in the Tablet PC is at.
Contact your sales outlet or our customer
service centre.
System CMOS checksum bad - default conguration
used
The system conguration information is
incorrect.
Switch off the Tablet PC.
Switch on the Tablet PC.
Keep the "Change screen orientation" tablet
button pressed and switch on the Tablet PC.
In the BIOS Setup, select the Exit menu.
Select the entry Load Setup Defaults.
Select OK and press the Enter key.
Extended memory failed at offset: xxxx Failing Bits:
zzzz zzzz
When testing the extended memory an error has
resulted at the address xxxx.
Contact your sales outlet or our customer
service centre.
Failure Fixed Disk n
The settings of the hard disk drive are incorrect.
Start the BIOS Setup (Primary Master
submenu) and select the correct settings.
Keyboard controller error Switch off your Tablet PC with the ON/OFF
switch.
Wait 3 - 5 seconds and switch on the Tablet
PC again.
Keyboard error If you are using an external keyboard:
Check the connection and reboot the Tablet
PC.
nn Stuck key Make sure that no key is pressed.
Operating system not found Check in the BIOS Setup whether your hard
disk has been set correctly.
Make sure that the operating system is
installed on the corresponding drive.
Press <F1> to resume, <F2> to SETUP
This error message appears if an error occurs
during the self-test before starting the operating
system.
Press the " Alt "key on the Tablet PC to boot
the operating system
Keep the "Change screen orientation"tablet
button pressed and switch on the Tablet PC
to access the BIOS setup.
Real time clock error Contact your sales outlet or our customer
service centre.
nnnnK Shadow RAM failed at offset: xxxx Failing
Bits: zzzz
Contact your sales outlet or our customer
service centre.
System battery is dead - Replace and run SETUP Contact your sales outlet or our customer
service centre.
System cache error - Cache disabled Contact your sales outlet or our customer
service centre.
System timer error Contact your sales outlet or our customer
service centre.
74 Fujitsu Technology Solutions
Technical data
Technical data
Tablet PC
General
Processor Intel Atom Z670
Main memory (SO DIMM) 2 GByte DDR2 onboard
Electrical data
Safety regulations complied with CE
Protection class II
Maximum power consumption: (Tablet PC on
with battery charging)
40 W
Touchscreen
Size 25.65 cm 16:10 TFT WXGA
Resolution 1280 x 800 pixels/16 million colours
Pixel class II
Brightness control 6 levels
Technology Wide-View High-Bright WXGA Display with LED
Background Lighting
Digitizer and glass panel Dual digitizer with matt touch screen
Cameras Front: VGA camera
Back: 1.3 megapixels
Graphics card
Chip Intel GMA 600
Maximum resolution on external display: 1280 x 720 pixels
Dimensions
Width x depth x height 275 mm x 192 mm x 16.2 mm
Weight depending on conguration from 0.76 kg with a 2-cell battery
from 0.87 kg with a 4-cell battery
Input devices
Tablet buttons 3 keys
Pen 1 freely programmable rocker button / eraser
Slots
Memory card slot 1 x SD or MS card
SmartCard slot 1 x
SIM card slot 1 x
Ports
HDMI port 1 x
Headphones port/Line Out 3.5 mm stereo mini jack
Docking port 1 x
USB (Universal Serial Bus) 1 x USB 2.0
Fujitsu Technology Solutions 75
Technical data
Ambient conditions
Environment class DIN IEC 721 7K1
Mechanism class DIN IEC 721 7M2
Operating temperature 5 .... 35
Transport temperature (2K2) 15C .... 60C
Rechargeable battery
You can nd information on the batteries used in your device at
"http://ts.fujitsu.com/support".
4-cell lithium polymer battery 5240
mAh
2-cell lithium polymer battery 2620
mAh
Rated voltage 7.2 V 7.2 V
Rated capacity 38 Wh 19 Wh
Mains adapter (40 W)
Technical data
Rated voltage 19 V
Max. rated current 2.1 A
An additional mains adapter or power cable can be ordered at any time.
Cradle (optional)
Electrical data
Safety regulations complied with CE
Protection class II
Ports
USB (Universal Serial Bus) 4 x USB 2.0
Docking port 30-pin
Ambient conditions
Environment class DIN IEC 721 7K1
Mechanism class DIN IEC 721 7M2
Operating temperature 5 C .... 35
Transport temperature 15 C .... 60
76 Fujitsu Technology Solutions
Manufacturers notes
Manufacturers notes
Disposal and recycling
Notes
Information about this subject can be found on your Tablet PC or on our Internet pages.
Declarations of Conformity
Declarationof conformity
The "Declarations of Conformity" for the device can be found at our Internet
address under: "http://ts.fujitsu.com/ce".
Fujitsu Technology Solutions hereby declares that your device is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Tested safety (TS, depending on the device)
With the AntiGlare display, the device meets
the requirements of the following directives:
EN60950-1:2001
DIN EN ISO 13406-2:2003
EK1-ITB 2000:2008
DIN EN ISO 9241-4:1999
Fujitsu Technology Solutions 77
Manufacturers notes
CE marking
CEmarking
CE marking for devices with radio component
This equipment complies with the requirements of Directive 1999/5/EC of the
European Parliament and Commission from 9 March, 1999 governing Radio
and Telecommunications Equipment and mutual recognition of conformity.
This equipment can be used in the following countries:
Belgium Bulgaria Denmark Germany
Estonia Finland France Greece
UK Ireland Iceland Italy
Latvia Liechtenstein Lithuania Luxembourg
Malta The
Netherlands
Norway Austria
Poland Portugal Rumania Sweden
Switzerland Slovakia Slovenia Spain
Czech Republic Hungary Cyprus

Contact the corresponding government ofce in the respective country for
current information on possible operating restrictions. If your country is
not included in the list, then please contact the corresponding supervisory
authority as to whether the use of this product is permitted in your country.
Regulatory notices
If there is no FCC logo and also no FCC ID on the device then this device is
not approved by the Federal Communications Commission (FCC) of the USA.
Although it is not explicitly forbidden to travel in the US trading area carrying this
device, to avoid trouble at customs clearance, Fujitsu Technology Solutions GmbH
recommends not to bring this device into the US trading area.
Regulatory information for Tablet PCs without radio device
Regulatoryinformation
NOTICE:
Changes or modications not expressly approved by Fujitsu Technology Solutions
could void this users authority to operate the equipment.
Notice to Users of Radios and Television
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
78 Fujitsu Technology Solutions
Manufacturers notes
Connect the equipment into an outlet that is on a different circuit than the receiver.
Consult the dealer or an experienced radio/TV technician for help.
Notice to Users of the US Telephone Network
Your Tablet PC may be supplied with an internal modem which complies with Part 68 of the
FCC rules. On this Tablet PC is a label that contains the FCC Registration Number and the
Ringer Equivalence Number (REN) for this equipment among other information. If requested,
the user must provide their telephone company with the following information:
1. The telephone number to which the Tablet PC is connected.
2. The Ringer Equivalence Number (REN) for this equipment.
3. The equipment requires a standard modular jack type USOC RJ-11C
which is FCC Part 68 compliant.
4. The FCC Registration Number.
This equipment is designed to be connected to the telephone network or premises wiring using
a standard modular jack type USOC RJ-11C which is FCC Part 68 compliant and a line cord
between the modem and the telephone network with a minimum of 26AWG.
The REN is used to determine the number of devices that you may connect to your telephone
line and still have all of those devices ring when your number is called. Too many devices
on one line may result in failure to ring in response to an incoming call. In most, but not all,
areas the sum of the RENs of all of the devices should not exceed ve (5). To be certain
of the number of devices you may connect to your line, as determined by the RENs, contact
your local telephone company. If this equipment causes harm to the telephone network, your
telephone company may discontinue your service temporarily. If possible, they will notify you
in advance. If advance notice is not practical they will notify you as soon as possible. You
will also be advised of your right to le a complaint with the FCC.
This fax modem also complies with fax branding requirements per FCC Part 68.
Your telephone company will probably ask you to disconnect this equipment from the telephone
network until the problem is corrected and you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin-operated telephones provided by your telephone
company. Connection to party lines is subject to state tariffs. Contact your states public utility
commission, public service commission or corporation commission for more information.
This equipment includes automatic dialing capability. When programming and/or
making test calls to emergency numbers:
Remain on the line and briey explain to the dispatcher the reason for the call.
Perform such activities in off-peak hours, such as early morning or late evening.
FCC rules prohibit the use of non-hearing aid compatible telephones in the
following locations or applications:
All public or semi-public coin-operated or credit card telephones.
Elevators, highways, tunnels (automobile, subway, railroad or pedestrian) where a
person with impaired hearing might be isolated in an emergency.
Places where telephones are specically installed to alert emergency authorities
such as re, police or medical assistance personnel.
Hospital rooms, residential health care facilities, convalescent homes and prisons.
Hotel, motel or apartment lobbies.
Stores where telephones are used by patrons to order merchandise.
Fujitsu Technology Solutions 79
Manufacturers notes
Public transportation terminals where telephones are used to call taxis or
to reserve lodging or rental cars.
In hotel and motel rooms as at least ten percent of the rooms must contain hearing
aid-compatible telephones or jacks for plug-in hearing aid compatible telephones which
will be provided to hearing impaired customers on request.
DOC (Industry CANADA) notices
DOC(INDUSTRYCANADA)NOTICES
Notice to Users of Radios and Television
This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment
Regulations.
CET appareil numrique de la class B respecte toutes les exigence du Rglement
sur le matrial brouilleur du Canada.
Notice to Users of the Canadian Telephone Network
NOTICE:
This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specications. This is conrmed by the registration number. The abbreviation, IC, before
the registration number signies that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specications were met. It does not
imply that Industry Canada approved the equipment. Before connecting this equipment to
a telephone line the user should ensure that it is permissible to connect this equipment to
the local telecommunication facilities. The user should be aware that compliance with the
certication standards does not prevent service degradation in some situations.
Repairs to telecommunication equipment should be made by a Canadian authorised
maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or
any equipment failures may give the telecommunication company cause to request the
user to disconnect the equipment from the telephone line.
NOTICE:
The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned
to each terminal equipment provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed ve.
CAUTION:
For safety, users should ensure that the electrical ground of the power utility, the
telephone lines and the metallic water pipes are connected together. Users should NOT
attempt to make such connections themselves but should contact the appropriate electric
inspection authority or electrician. This may be particularly important in rural areas.
Avis Aux Utilisateurs Du Rseau Tlphonique Canadien
AVIS : Le prsent matriel est conforme aux spcications techniques dIndustrie Canada
applicables au matriel terminal. Cette conformit est conrme par le numro denregistrement.
Le sigle IC, plac devant le numro denregistrement, signie que lenregistrement sest effectu
conformment une dclaration de conformit et indique que les spcications techniques
dIndustrie Canada ont t respectes. Il nimplique pas quIndustrie Canada a approuv le matriel.
80 Fujitsu Technology Solutions
Manufacturers notes
Avant de connecter cet quipement une ligne tlphonique, lutilisateur doit vrier
sil est permis de connecter cet quipement aux installations de tlcommunications
locales. Lutilisateur est averti que mme la conformit aux normes de certication ne
peut dans certains cas empcher la dgradation du service.
Les rparations de lquipement de tlcommunications doivent tre effectues par un service de
maintenance agr au Canada. Toute rparation ou modication, qui nest pas expressment
approuve par Fujitsu, ou toute dfaillance de lquipement peut entraner la compagnie de
tlcommunications exiger que lutilisateur dconnecte lquipement de la ligne tlphonique.
AVIS : Lindice dquivalence de la sonnerie (IES) du prsent matriel est de 0.0. LIES
assign chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent
tre raccords une interface tlphonique. La terminaison dune interface peut consister
en une combinaison quelconque de dispositifs, la seule condition que la somme dindices
dquivalence de la sonnerie de tous les dispositifs nexcde pas 5.
AVERTISSEMENT:
Pour assurer la scurit, les utilisateurs doivent vrier que la prise de terre du service
dlectricit, les lignes tlphoniques et les conduites deau mtalliques sont connectes
ensemble. Les utilisateurs NE doivent PAS tenter dtablir ces connexions eux-mmes,
mais doivent contacter les services dinspection dinstallations lectriques appropris
ou un lectricien. Ceci peut tre particulirement important en rgions rurales.
UL Notice
This unit requires an AC adapter to operate. Only use a UL Listed Class 2 adapter.
The correct output rating is indicated on the AC adapter label. Refer to the illustration
below for the correct AC Adapter output polarity:
CAUTION:
To reduce the risk of re, use only 26AWG or larger telecommunications line cord.
For Authorized Repair Technicians Only
CAUTION:
For continued protection against risk of re, replace only with the
same type and rating fuse.
WARNING:
Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturers instructions.
FCC Regulatory information for Tablet PCs with radio device
Regulatoryinformation
Federal Communications Commission statement
Fujitsu Technology Solutions 81
Manufacturers notes
This device complies with Part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of this device.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy. If not installed and used in accordance with
the instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the distance between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from the one the receiver is connected to.
4. Consult the dealer or an experienced radio/TV technician for help.
Please note the following regulatory information related to the optional radio device.
FCC Radio Frequency Exposure statement
This radio device has been evaluated under FCC Bulletin OET 65C and found compliant with the
requirements as set forth in CFR 47 Sections 2.1091, 2.1093, and 15.247 (b) (4) addressing RF
Exposure from radio frequency devices. The radiated output power of this radio device is far below
the FCC radio frequency exposure limits. Nevertheless, this device shall be used in such a manner
that the potential for human contact during normal operation is minimized. When using this device, a
certain separation distance between antenna and nearby persons must be maintained to ensure RF
exposure compliance. In order to comply with RF exposure limits established in the ANSI C95.1
standards, the distance between the antennas and the user should not be less than 20 cm (8 inches).
Regulatory Notes and Statements
Radio device, health and authorisation for use
Radio-frequency electromagnetic energy is emitted from the wireless devices. The energy levels
of these emissions, however, are far much less than the electromagnetic energy emissions from
wireless devices such as mobile phones. Radio devices are safe for use by consumers because
they operate within the guidelines found in radio frequency safety standards and recommendations.
The use of the radio devices may be restricted in some situations or environments, such as:
on board an airplane, or
in an explosive environment, or
in situations where the interference risk to other devices or services is
perceived or identied as harmful.
In cases in which the policy regarding use of radio devices in specic environments is not
clear (e.g., airports, hospitals, chemical/oil/gas industrial plants, private buildings), obtain
authorization to use these devices prior to operating the equipment.
Regulatory Information/Disclaimers
82 Fujitsu Technology Solutions
Manufacturers notes
Installation and use of this radio device must be in strict accordance with the instructions included
in the user documentation provided with the product. Any changes or modications made to this
device that are not expressly approved by the manufacturer may void the users authority to operate
the equipment. The manufacturer is not responsible for any radio or television interference caused
by unauthorized modication of this device, or the substitution or attachment of connecting cables
and equipment other than those specied by the manufacturer. It is the responsibility of the user
to correct any interference caused by such unauthorized modication, substitution or attachment.
The manufacturer and its authorized resellers or distributors will assume no liability for any damage
or violation of government regulations arising from failure to comply with these guidelines.
Export restrictions
This product or software contains encryption code which may not be exported or
transferred from the US or Canada without an approved US Department of Commerce
export license. This device complies with Part 15 of FCC Rules, as well as ICES 003 B
/ NMB 003 B. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesirable operation.
Modications not expressly authorised by Fujitsu Technology Solutions may
invalidate the users right to operate this equipment.
Fujitsu Technology Solutions 83
Index
Index
A
Acoustic error messages 73
Audio ports 63
B
Battery
battery life 39
caring for and maintaining 40
charge level 40, 43
charging 40
self-discharge 40
storage 40
Battery status meter 40
Battery:
discharges too quickly 72
BIOS Setup Utility
calling 64
exiting 66
operating 65
protecting with password 54
settings 64
Bluetooth
Switching off module 47
Switching on module 47
Bluetooth, safety notes 11
Buffer battery, load 68
C
CE marking 78
Charging capacity, battery 40
Cleaning 16
Conguration, BIOS Setup Utility 64
Connecting audio devices 63
Connecting headphones 63
Cradle
Connecting a Tablet PC 50
Ports 49
Crystal View display
cleaning 16
D
Date is incorrect 68
Declaration of conformity 77
Device
setting up 18
Devices
connecting 60
disconnecting 60
Display orientation
selecting 23
DOC (INDUSTRY CANADA) NOTICES 80
E
Energy
energy saving 15
Energy saving 15
Energy saving mode
leaving 71
Error message:
on the screen 73
Error messages on the screen 73
Errors
Acoustic warnings 73
F
Fault
correction 67
Fingerprint sensor 53
congure 53
First-time setup 17
G
Getting started 17
GPS 48
H
Hardware conguration 64
HDMI port 61
I
Important notes 11
Incorrect date/time 68
K
Keyboard
cleaning 16
L
Landscape orientation
screen 23
Life, battery 39
M
Mains adapter
connecting 18
setting up 18
84 Fujitsu Technology Solutions
Index
Memory card
handling 44
inserting 44
removing 45
Mobile operation 15
Monitor
drifting display 69
remains blank 69
N
Notes 11
cleaning 16
disposal / recycling 77
energy saving 15
Safety 11
touchscreen 22
transport 15
O
Operating system
activating system protection 56
cancel system protection 56
protecting with password 55
P
Packaging 17
Password
changing 55
entering 55
removing 55
Password protection 54
Password protection:
hard disk 56
Peripheral devices
connecting 60
disconnecting 60
Portrait orientation
screen 23
Ports
Cradle 49
Power
power consumption 43
power-management features 43
Power-on indicator 21
Preparing for operation 18
Printer does not print 71
R
Radio component:
safety notes 11
Rechargeable battery 39
see Battery 39
Regulatory information
Tablet PCs with radio device 81
Tablet PCs without radio device 78
S
Safety notes 11
Screen
no screen display 69
Security functions 53
SystemLock 58
Security functions,
SmartCard 58
Selecting a location 18
Self-discharge, battery 40
Setup
see BIOS Setup Utility 64
Slot
Memory cards 44
Status indicators 20
Summer time 68
Supervisor password
changing 55
entering 55
removing 55
Suspend/Resume button 21
Switching on for the rst time 19
Symbols
indicators 20
System conguration 64
System settings, BIOS Setup Utility 64
T
Tablet PC
before you travel 15
cleaning 16
switching off 21
transporting 1516
using 20
Tablet PC, operation 20
Tablet PC: switching on 21
Technical data
Mains adapter 76
The radio connection to a network does
not work 71
The Tablet PC
cannot be started 70
doesnt work. 71
Time not correct 68
Time, daylight savings 68
Tips 67
Fujitsu Technology Solutions 85
Index
Touchpad
cleaning 16
Touchscreen
cleaning 16
difcult to read 68
notes 22
reected glare 68
remains blank 68
touchscreen is too dark 68
TPM 59
Transport
Transport damage 17
Transportation 1516
Travel, Tablet PC 15
Troubleshooting 67
Trusted Platform Module 59
U
USB ports 62
User password
changing 55
entering 55
removing 55
W
Webcam 39
Wireless LAN
Switching off module 47
Switching on module 47
Wireless LAN:
safety notes 11
86 Fujitsu Technology Solutions