Scribd
Upload
284 views

Cam Profile Analysis

This document describes how to graphically analyze cam profiles using a cam-follower mechanism. It explains that a cam rotates and imparts reciprocating or oscillating motion to the follower. To visualize the follower's motion, a displacement diagram is drawn based on the follower's motion over one revolution of the cam. Then, the cam profile is constructed by positioning the follower at different angular positions of the cam based on the displacement diagram. Two methods are provided to draw the cam profile when the follower axis passes through or is offset from the cam shaft axis.

Uploaded by

PremjeetSingh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
284 views

Cam Profile Analysis

This document describes how to graphically analyze cam profiles using a cam-follower mechanism. It explains that a cam rotates and imparts reciprocating or oscillating motion to the follower. To visualize the follower's motion, a displacement diagram is drawn based on the follower's motion over one revolution of the cam. Then, the cam profile is constructed by positioning the follower at different angular positions of the cam based on the displacement diagram. Two methods are provided to draw the cam profile when the follower axis passes through or is offset from the cam shaft axis.

Uploaded by

PremjeetSingh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

EXPERIMENT

AIM- Cam Profile Analysis (Graphical Method)


APPARATUS REQUIRED- Cam-Follower Mechanism
THEORY- A cam is a rotating machine element which gives reciprocating or
oscillating motion to another element known as follower. The cam and the follower
have a line contact and constitute a higher pair. The cams are usually rotated at
uniform speed by a shaft, but the follower motion is pre-determined and will be
according to the shape of the cam.
A cam profile is drawn to visualize the motion of the follower along the revolution
of cam.
In order to draw the cam profile for a radial cam, first of all the displacement
diagram for the given motion of the follower is drawn. Then by constructing the
follower in its proper position at each angular position, the profile of the working
surface of the cam is drawn. In constructing the cam profile, the principle of
kinematic inversion is used, i.e.the cam is imagined to be stationary and the
follower is allowed to rotate in the opposite direction to the cam rotation.
PROCEDURE-
The displacement diagram, as shown in Fig is drawn as discussed in the
following steps :
1. Draw a horizontal line AX= 360 to some suitable scale. On this line, mark AS=
60 to represent outstroke of the follower, ST= 30 to represent dwell, TP= 60 to
represent return stroke and PX= 210 to represent dwell.
2. Draw vertical line AY equal to the stroke of the follower (i.e.40 mm) and
complete the rectangle as shown in fig.
3. Divide the angular displacement during outstroke and return stroke into any
equal number of even parts (say six) and draw vertical lines through each point.
4. Since the follower moves with uniform velocity during outstroke and return
stroke, there-fore the displacement diagram consists of straight lines. Join AG and
HP.
5. The complete displacement diagram is shown by AGHPX in Fig.

DISPLACEMENT DIAGRAM
(a) Profile of the cam when the axis of follower passes through the axis of cam
shaft
The profile of the cam when the axis of the follower passes through the axis of
the cam shaft, as shown in Fig, is drawn as discussed in the following steps :
1. Draw a base circle with radius equal to the minimum radius of the cam (i.e.50
mm) with O as centre.
2. Since the axis of the follower passes through the axis of the cam shaft, therefore
mark trace point A, as shown in Fig.
3. From OA, mark angle AOS= 60 to represent outstroke, angle SOT= 30 to
represent dwell and angle TOP= 60 to represent return stroke.
4. Divide the angular displacements during outstroke and return stroke (i.e. angle
AOS and angle TOP) into the same number of equal even parts as in displacement
diagram.
5. Join the points 1, 2, 3 ...etc. and 0 , 1 , 2, 3 , ... etc. with centre O and
produce beyond the base circle as shown in Fig.
6. Now set off 1B, 2C, 3D... etc. and 0 H, 1 J... etc. from the displacement
diagram.
7. Join the points A, B, C,... M, N, P with a smooth curve. The curve AGHPA is
the complete profile of the cam.

CAM PROFILE

(b) Profile of the cam when the axis of the follower is offset by 20 mm from the
axis of the cam shaft
The profile of the cam when the axis of the follower is offset from the axis of
the cam shaft, as shown in Fig. 20.12, is drawn as discussed in the following
steps :
1. Draw a base circle with radius equal to the minimum radius of the cam (i.e.50
mm) with O as centre.
2. Draw the axis of the follower at a distance of 20 mm from the axis of the cam,
which intersects the base circle at A.
3. Join AO and draw an offset circle of radius 20 mm with centre O.
4. From OA, mark angle AOS= 60 to represent outstroke, angle SOT= 30 to
represent dwell and angle TOP= 60 to represent return stroke.
5. Divide the angular displacement during outstroke and return stroke (i.e.angle
AOS and angle TOP) into the same number of equal even parts as in displacement
diagram.
6. Now from the points 1, 2, 3 ... etc. and 0,1,2,3 ... etc. on the base circle,
draw tangents to the offset circle and produce these tangents beyond the base circle
as shown in Fig.
7. Now set off 1B, 2C, 3D... etc. and 0 H, 1 J... etc. from the displacement
diagram.
8. Join the points A, B, C...M, N, P with a smooth curve. The curve AGHPA is the
complete profile of the cam.


CAM PROFILE

You might also like