s1

Agilent N6462A DDR4

Compliance Test
Application
Programmer's Reference
Notices
Agilent Technologies, Inc. 2005-2014
No part of this manual may be reproduced
in any form or by any means (including
electronic storage and retrieval or transla-
tion into a foreign language) without prior
agreement and written consent from Agi-
lent Technologies, Inc. as governed by
United States and international copyright
laws.
Manual Part Number
Version 01.02.0000
Edition
April 29, 2013
Available in electronic format only
Agilent Technologies, Inc.
1900 Garden of the Gods Road
Colorado Springs, CO 80907 USA
Warranty
The material contained in this docu-
ment is provided as is, and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connection
with the furnishing, use, or perfor-
mance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a
license and may be used or copied only in
accordance with the terms of such license.
Restricted Rights Legend
If software is for use in the performance of
a U.S. Government prime contract or sub-
contract, Software is delivered and
licensed as Commercial computer soft-
ware as defined in DFAR 252.227-7014
(June 1995), or as a commercial item as
defined in FAR 2.101(a) or as Restricted
computer software as defined in FAR
52.227-19 (June 1987) or any equivalent
agency regulation or contract clause. Use,
duplication or disclosure of Software is
subject to Agilent Technologies standard
commercial license terms, and non-DOD
Departments and Agencies of the U.S. Gov-
ernment will receive no greater than
Restricted Rights as defined in FAR
52.227-19(c)(1-2) (June 1987). U.S. Govern-
ment users will receive no greater than
Limited Rights as defined in FAR 52.227-14
(June 1987) or DFAR 252.227-7015 (b)(2)
(November 1995), as applicable in any
technical data.
Safety Notices
CAUTI ON
A CAUTION notice denotes a haz-
ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood and
met.
WARNI NG
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and met.


Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 3
In This Book
This book is your guide to programming the Agilent Technologies N6462A
DDR4 Compliance Test Application.
Chapter 1, Introduction to Programming, starting on page 7, describes
compliance application programming basics.
Chapter 2, Configuration Variables and Values, starting on page 11,
Chapter 3, Test Names and IDs, starting on page 53, and Chapter 4,
Instruments, starting on page 59, provide information specific to
programming the N6462A DDR4 Compliance Test Application.
How to Use This
Book
Programmers who are new to compliance application programming should
read all of the chapters in order. Programmers who are already familiar
with this may review chapters 2, 3, and 4 for changes.

4 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 5

Contents
In This Book 3
1 Introduction to Programming
Remote Programming Toolkit 8
Licensing 9
2 Configuration Variables and Values
3 Test Names and IDs
4 Instruments
Index
6 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference

s1
7

Agilent N6462A DDR4 Compliance Test Application
Programmer's Reference
1
Introduction to Programming
Remote Programming Toolkit 8
Licensing 9
This chapter introduces the basics for remote programming a compliance
application. The programming commands provide the means of remote
control. Basic operations that you can do remotely with a computer and a
compliance app running on an oscilloscope include:
Launching and closing the application.
Configuring the options.
Running tests.
Getting results.
Controlling when and were dialogs get displayed
Saving and loading projects.
You can accomplish other tasks by combining these functions.
8 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
1 Introduction to Programming

Remote Programming Toolkit
The majority of remote interface features are common across all the
Agilent Technologies, Inc. family of compliance applications. Information
on those features is provided in the N5452A Compliance Application
Remote Programming Toolkit available for download from Agilent here:
"www.agilent.com/find/scope- apps- sw". The N6462A DDR4 Compliance Test
Application uses Remote Interface Revision 2.70. The help files provided
with the toolkit indicate which features are supported in this version.
In the toolkit, various documents refer to "application- specific
configuration variables, test information, and instrument information".
These are provided in Chapters 2, 3, and 4 of this document, and are also
available directly from the application's user interface when the remote
interface is enabled (View>Preferences::Remote tab::Show remote interface
hints). See the toolkit for more information.
Introduction to Programming 1
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 9

Licensing
To enable programming of compliance applications on your oscilloscope,
please visit "www.agilent.com/find/scope- apps" to purchase an N5452A
remote programming option license.
10 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
1 Introduction to Programming

s1
11

Agilent N6462A DDR4 Compliance Test Application
Programmer's Reference
2
Configuration Variables and Values
The following table contains a description of each of the N6462A DDR4
Compliance Test Application options that you may query or set remotely
using the appropriate remote interface method. The columns contain this
information:
GUI Location Describes which graphical user interface tab contains
the control used to change the value.
Label Describes which graphical user interface control is used to
change the value.
Variable The name to use with the SetConfig method.
Values The values to use with the SetConfig method.
Description The purpose or function of the variable.
For example, if the graphical user interface contains this control on the
Set Up tab:
Enable Advanced Features
then you would expect to see something like this in the table below:
and you would set the variable remotely using:
ARSL syntax
-----------
arsl -a ipaddress -c "SetConfig 'EnableAdvanced' 'True'"
C# syntax
---------
remoteAte.SetConfig("EnableAdvanced", "True");
Table 1 Example Configuration Variables and Values
GUI
Location
Label Variable Values Description
Set Up Enable Advanced
Features
EnableAdvanced True, False Enables a set of optional
features.
12 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Here are the actual configuration variables and values used by this
application:
NOTE
Some of the values presented in the table below may not be available in certain
configurations. Always perform a "test run" of your remote script using the application's
graphical user interface to ensure the combinations of values in your program are valid.
NOTE
The file, ""ConfigInfo.txt"", which may be found in the same directory as this help file,
contains all of the information found in the table below in a format suitable for parsing.
Table 2 Configuration Variables and Values
GUI
Location
Label Variable Values Description
Confgure A12-BC
Channel
A12BCDi
gChannel
NA, DIGital0, DIGital1, DIGital2, DIGital3, DIGital4,
DIGital5, DIGital6, DIGital7, DIGital8, DIGital9,
DIGital10, DIGital11, DIGital12, DIGital13, DIGital14,
DIGital15
Identifies the channel source
selection of the A12-BC
digital signal to be analyzed
for burst length detection.
Confgure ACT
Channel
ACTDigC
hannel
DIGital0, DIGital1, DIGital2, DIGital3, DIGital4,
DIGital5, DIGital6, DIGital7, DIGital8, DIGital9,
DIGital10, DIGital11, DIGital12, DIGital13, DIGital14,
DIGital15
Identifies the channel source
selection of the ACT digital
signal to be analyzed for
MSOx Logic Triggering.
Confgure Base
Ratio
BurstTrig
gerBase
Ratio_Ch
an1
(Accepts user-defined text), 0.20 Specify the value of the base
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Confgure Base
Ratio
BurstTrig
gerBase
Ratio_Ch
an2
(Accepts user-defined text), 0.20 Specify the value of the base
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Confgure Base
Ratio
BurstTrig
gerBase
Ratio_Ch
an3
(Accepts user-defined text), 0.20 Specify the value of the base
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 13

Confgure Base
Ratio
BurstTrig
gerBase
Ratio_Ch
an4
(Accepts user-defined text), 0.20 Specify the value of the base
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Confgure Burst
Envelope
Threshol
d
BurstEnv
Thres
(Accepts user-defined text), 0.5 This setting is used to
determine the Data Strobe
burst sensitivity level when
performing the READ/WRITE
burst separation process.
Setting this option to a
smaller value will increase
the sensitivity of the
algoritm. This option can be
used to detect and identify
the smallest valid
READ/WRITE Data Strobe
burst within a data
acquisition if there are
significant difference in
amplitude between the Data
Strobe bursts. However,
setting this option too small
may cause noise to be
interpreted as valid burst
data.
Confgure Burst
Length
Limit
MaxBurs
tLenLimit
(Accepts user-defined text), 4, 8, 10000 This value is used to limit the
maximum number of bits
used in a valid data burst
found when generating an
eye diagram(Read or Write).
For example, when this value
is set to '8', the maximum
number of bits used in a data
burst to generate an eye
diagram is limit to the first 8
data bit. User can specify
custom value for this option.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
14 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Burst
Length
Stimulus
Mode
BurstLen
gthStimu
lusMode
FixedBurstLength, A12BCOnTheFly This configuration for the
selection of burst length
stimulus mode. For "Fixed
Burst Length" selection,
application will assume all
the burst occurance have the
same length of sub-burst. For
"A12-BC Signal(Support
On-The-Fly)" selection, the
burst length of a sub-burst is
depend on the logic state of
BC signal at the moment
Read/Write command
queried.
Confgure CAS
Channel
CASDigC
hannel
DIGital0, DIGital1, DIGital2, DIGital3, DIGital4,
DIGital5, DIGital6, DIGital7, DIGital8, DIGital9,
DIGital10, DIGital11, DIGital12, DIGital13, DIGital14,
DIGital15
Identifies the channel source
selection of the CAS digital
signal to be analyzed for
MSOx Logic Triggering.
Confgure CKE
Channel
CKEDigC
hannel
Ignore, DIGital0, DIGital1, DIGital2, DIGital3,
DIGital4, DIGital5, DIGital6, DIGital7, DIGital8,
DIGital9, DIGital10, DIGital11, DIGital12, DIGital13,
DIGital14, DIGital15
Identifies the channel source
selection of the CKE digital
signal to be analyzed for
MSOx Logic Triggering.
Confgure CS
Channel
CSDigCh
annel
DIGital0, DIGital1, DIGital2, DIGital3, DIGital4,
DIGital5, DIGital6, DIGital7, DIGital8, DIGital9,
DIGital10, DIGital11, DIGital12, DIGital13, DIGital14,
DIGital15
Identifies the channel source
selection of the CS digital
signal to be analyzed for
MSOx Logic Triggering.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 15

Confgure Channel
1
MyCH1 NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2, Data_DQ0,
Data_DQ1, Data_DQ2, Data_DQ3, Data_DQ4,
Data_DQ5, Data_DQ6, Data_DQ7, Data_DQ8,
Data_DQ9, Data_DQ10, Data_DQ11, Data_DQ12,
Data_DQ13, Data_DQ14, Data_DQ15, Data_DQ16,
Data_DQ17, Data_DQ18, Data_DQ19, Data_DQ20,
Data_DQ21, Data_DQ22, Data_DQ23, Data_DQ24,
Data_DQ25, Data_DQ26, Data_DQ27, Data_DQ28,
Data_DQ29, Data_DQ30, Data_DQ31, Data_DQ32,
Data_DQ33, Data_DQ34, Data_DQ35, Data_DQ36,
Data_DQ37, Data_DQ38, Data_DQ39, Data_DQ40,
Data_DQ41, Data_DQ42, Data_DQ43, Data_DQ44,
Data_DQ45, Data_DQ46, Data_DQ47, Data_DQ48,
Data_DQ49, Data_DQ50, Data_DQ51, Data_DQ52,
Data_DQ53, Data_DQ54, Data_DQ55, Data_DQ56,
Data_DQ57, Data_DQ58, Data_DQ59, Data_DQ60,
Data_DQ61, Data_DQ62, Data_DQ63, Data_DQ64,
Data_DQ65, Data_DQ66, Data_DQ67, Data_DQ68,
Data_DQ69, Data_DQ70, Data_DQ71,
Control_NCS0, Control_NCS1, Strobe_DDQS0,
Strobe_DDQS1, Strobe_DDQS2, Strobe_DDQS3,
Strobe_DDQS4, Strobe_DDQS5, Strobe_DDQS6,
Strobe_DDQS7, Strobe_DDQS8, Strobe_SDQS0,
Strobe_SDQS1, Strobe_SDQS2, Strobe_SDQS3,
Strobe_SDQS4, Strobe_SDQS5, Strobe_SDQS6,
Strobe_SDQS7, Strobe_SDQS8, DM_DM0,
DM_DM1, DM_DM2, DM_DM3, DM_DM4,
DM_DM5, DM_DM6, DM_DM7, LP_NA_,
LP_Clock_DCK, LP_Clock_SCK, LP_Data_DQ0,
LP_Data_DQ1, LP_Data_DQ2, LP_Data_DQ3,
LP_Data_DQ4, LP_Data_DQ5, LP_Data_DQ6,
LP_Data_DQ7, LP_Data_DQ8, LP_Data_DQ9,
LP_Data_DQ10, LP_Data_DQ11, LP_Data_DQ12,
LP_Data_DQ13, LP_Data_DQ14, LP_Data_DQ15,
LP_Data_DQ16, LP_Data_DQ17, LP_Data_DQ18,
LP_Data_DQ19, LP_Data_DQ20, LP_Data_DQ21,
LP_Data_DQ22, LP_Data_DQ23, LP_Data_DQ24,
LP_Data_DQ25, LP_Data_DQ26, LP_Data_DQ27,
LP_Data_DQ28, LP_Data_DQ29, LP_Data_DQ30,
LP_Data_DQ31, LP_Control_NCS,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3,
LP_DM_DM0, LP_DM_DM1, LP_DM_DM2,
LP_DM_DM3
Please select the signal
parameter connected to
Channel 1
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
16 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Channel
2
MyCH2 NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2, Data_DQ0,
Data_DQ1, Data_DQ2, Data_DQ3, Data_DQ4,
Data_DQ5, Data_DQ6, Data_DQ7, Data_DQ8,
Data_DQ9, Data_DQ10, Data_DQ11, Data_DQ12,
Data_DQ13, Data_DQ14, Data_DQ15, Data_DQ16,
Data_DQ17, Data_DQ18, Data_DQ19, Data_DQ20,
Data_DQ21, Data_DQ22, Data_DQ23, Data_DQ24,
Data_DQ25, Data_DQ26, Data_DQ27, Data_DQ28,
Data_DQ29, Data_DQ30, Data_DQ31, Data_DQ32,
Data_DQ33, Data_DQ34, Data_DQ35, Data_DQ36,
Data_DQ37, Data_DQ38, Data_DQ39, Data_DQ40,
Data_DQ41, Data_DQ42, Data_DQ43, Data_DQ44,
Data_DQ45, Data_DQ46, Data_DQ47, Data_DQ48,
Data_DQ49, Data_DQ50, Data_DQ51, Data_DQ52,
Data_DQ53, Data_DQ54, Data_DQ55, Data_DQ56,
Data_DQ57, Data_DQ58, Data_DQ59, Data_DQ60,
Data_DQ61, Data_DQ62, Data_DQ63, Data_DQ64,
Data_DQ65, Data_DQ66, Data_DQ67, Data_DQ68,
Data_DQ69, Data_DQ70, Data_DQ71,
Control_NCS0, Control_NCS1, Strobe_DDQS0,
Strobe_DDQS1, Strobe_DDQS2, Strobe_DDQS3,
Strobe_DDQS4, Strobe_DDQS5, Strobe_DDQS6,
Strobe_DDQS7, Strobe_DDQS8, Strobe_SDQS0,
Strobe_SDQS1, Strobe_SDQS2, Strobe_SDQS3,
Strobe_SDQS4, Strobe_SDQS5, Strobe_SDQS6,
Strobe_SDQS7, Strobe_SDQS8, DM_DM0,
DM_DM1, DM_DM2, DM_DM3, DM_DM4,
DM_DM5, DM_DM6, DM_DM7, LP_NA_,
LP_Clock_DCK, LP_Clock_SCK, LP_Data_DQ0,
LP_Data_DQ1, LP_Data_DQ2, LP_Data_DQ3,
LP_Data_DQ4, LP_Data_DQ5, LP_Data_DQ6,
LP_Data_DQ7, LP_Data_DQ8, LP_Data_DQ9,
LP_Data_DQ10, LP_Data_DQ11, LP_Data_DQ12,
LP_Data_DQ13, LP_Data_DQ14, LP_Data_DQ15,
LP_Data_DQ16, LP_Data_DQ17, LP_Data_DQ18,
LP_Data_DQ19, LP_Data_DQ20, LP_Data_DQ21,
LP_Data_DQ22, LP_Data_DQ23, LP_Data_DQ24,
LP_Data_DQ25, LP_Data_DQ26, LP_Data_DQ27,
LP_Data_DQ28, LP_Data_DQ29, LP_Data_DQ30,
LP_Data_DQ31, LP_Control_NCS,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3,
LP_DM_DM0, LP_DM_DM1, LP_DM_DM2,
LP_DM_DM3
Please select the signal
parameter connected to
Channel 2
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 17

Confgure Channel
3
MyCH3 NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2, Data_DQ0,
Data_DQ1, Data_DQ2, Data_DQ3, Data_DQ4,
Data_DQ5, Data_DQ6, Data_DQ7, Data_DQ8,
Data_DQ9, Data_DQ10, Data_DQ11, Data_DQ12,
Data_DQ13, Data_DQ14, Data_DQ15, Data_DQ16,
Data_DQ17, Data_DQ18, Data_DQ19, Data_DQ20,
Data_DQ21, Data_DQ22, Data_DQ23, Data_DQ24,
Data_DQ25, Data_DQ26, Data_DQ27, Data_DQ28,
Data_DQ29, Data_DQ30, Data_DQ31, Data_DQ32,
Data_DQ33, Data_DQ34, Data_DQ35, Data_DQ36,
Data_DQ37, Data_DQ38, Data_DQ39, Data_DQ40,
Data_DQ41, Data_DQ42, Data_DQ43, Data_DQ44,
Data_DQ45, Data_DQ46, Data_DQ47, Data_DQ48,
Data_DQ49, Data_DQ50, Data_DQ51, Data_DQ52,
Data_DQ53, Data_DQ54, Data_DQ55, Data_DQ56,
Data_DQ57, Data_DQ58, Data_DQ59, Data_DQ60,
Data_DQ61, Data_DQ62, Data_DQ63, Data_DQ64,
Data_DQ65, Data_DQ66, Data_DQ67, Data_DQ68,
Data_DQ69, Data_DQ70, Data_DQ71,
Control_NCS0, Control_NCS1, Strobe_DDQS0,
Strobe_DDQS1, Strobe_DDQS2, Strobe_DDQS3,
Strobe_DDQS4, Strobe_DDQS5, Strobe_DDQS6,
Strobe_DDQS7, Strobe_DDQS8, Strobe_SDQS0,
Strobe_SDQS1, Strobe_SDQS2, Strobe_SDQS3,
Strobe_SDQS4, Strobe_SDQS5, Strobe_SDQS6,
Strobe_SDQS7, Strobe_SDQS8, DM_DM0,
DM_DM1, DM_DM2, DM_DM3, DM_DM4,
DM_DM5, DM_DM6, DM_DM7, LP_NA_,
LP_Clock_DCK, LP_Clock_SCK, LP_Data_DQ0,
LP_Data_DQ1, LP_Data_DQ2, LP_Data_DQ3,
LP_Data_DQ4, LP_Data_DQ5, LP_Data_DQ6,
LP_Data_DQ7, LP_Data_DQ8, LP_Data_DQ9,
LP_Data_DQ10, LP_Data_DQ11, LP_Data_DQ12,
LP_Data_DQ13, LP_Data_DQ14, LP_Data_DQ15,
LP_Data_DQ16, LP_Data_DQ17, LP_Data_DQ18,
LP_Data_DQ19, LP_Data_DQ20, LP_Data_DQ21,
LP_Data_DQ22, LP_Data_DQ23, LP_Data_DQ24,
LP_Data_DQ25, LP_Data_DQ26, LP_Data_DQ27,
LP_Data_DQ28, LP_Data_DQ29, LP_Data_DQ30,
LP_Data_DQ31, LP_Control_NCS,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3,
LP_DM_DM0, LP_DM_DM1, LP_DM_DM2,
LP_DM_DM3
Please select the signal
parameter connected to
Channel 3
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
18 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Channel
4
MyCH4 NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2, Data_DQ0,
Data_DQ1, Data_DQ2, Data_DQ3, Data_DQ4,
Data_DQ5, Data_DQ6, Data_DQ7, Data_DQ8,
Data_DQ9, Data_DQ10, Data_DQ11, Data_DQ12,
Data_DQ13, Data_DQ14, Data_DQ15, Data_DQ16,
Data_DQ17, Data_DQ18, Data_DQ19, Data_DQ20,
Data_DQ21, Data_DQ22, Data_DQ23, Data_DQ24,
Data_DQ25, Data_DQ26, Data_DQ27, Data_DQ28,
Data_DQ29, Data_DQ30, Data_DQ31, Data_DQ32,
Data_DQ33, Data_DQ34, Data_DQ35, Data_DQ36,
Data_DQ37, Data_DQ38, Data_DQ39, Data_DQ40,
Data_DQ41, Data_DQ42, Data_DQ43, Data_DQ44,
Data_DQ45, Data_DQ46, Data_DQ47, Data_DQ48,
Data_DQ49, Data_DQ50, Data_DQ51, Data_DQ52,
Data_DQ53, Data_DQ54, Data_DQ55, Data_DQ56,
Data_DQ57, Data_DQ58, Data_DQ59, Data_DQ60,
Data_DQ61, Data_DQ62, Data_DQ63, Data_DQ64,
Data_DQ65, Data_DQ66, Data_DQ67, Data_DQ68,
Data_DQ69, Data_DQ70, Data_DQ71,
Control_NCS0, Control_NCS1, Strobe_DDQS0,
Strobe_DDQS1, Strobe_DDQS2, Strobe_DDQS3,
Strobe_DDQS4, Strobe_DDQS5, Strobe_DDQS6,
Strobe_DDQS7, Strobe_DDQS8, Strobe_SDQS0,
Strobe_SDQS1, Strobe_SDQS2, Strobe_SDQS3,
Strobe_SDQS4, Strobe_SDQS5, Strobe_SDQS6,
Strobe_SDQS7, Strobe_SDQS8, DM_DM0,
DM_DM1, DM_DM2, DM_DM3, DM_DM4,
DM_DM5, DM_DM6, DM_DM7, LP_NA_,
LP_Clock_DCK, LP_Clock_SCK, LP_Data_DQ0,
LP_Data_DQ1, LP_Data_DQ2, LP_Data_DQ3,
LP_Data_DQ4, LP_Data_DQ5, LP_Data_DQ6,
LP_Data_DQ7, LP_Data_DQ8, LP_Data_DQ9,
LP_Data_DQ10, LP_Data_DQ11, LP_Data_DQ12,
LP_Data_DQ13, LP_Data_DQ14, LP_Data_DQ15,
LP_Data_DQ16, LP_Data_DQ17, LP_Data_DQ18,
LP_Data_DQ19, LP_Data_DQ20, LP_Data_DQ21,
LP_Data_DQ22, LP_Data_DQ23, LP_Data_DQ24,
LP_Data_DQ25, LP_Data_DQ26, LP_Data_DQ27,
LP_Data_DQ28, LP_Data_DQ29, LP_Data_DQ30,
LP_Data_DQ31, LP_Control_NCS,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3,
LP_DM_DM0, LP_DM_DM1, LP_DM_DM2,
LP_DM_DM3
Please select the signal
parameter connected to
Channel 4
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 19

Confgure Chip
Select
Source
AdvDbg_
Source3
-1, 1, 2, 3, 4 Identifies the source of the
Chip Select signal for eye
diagram tests(Rank
separation option ONLY).
Confgure Clock
Lane
AdvDbgS
upportCl
ockMSO
xLogicTri
g
CK0, CK1, CK2 Identifies the Clock lane for
the eye diagram tests using
MSOX Logic input.
Confgure Clock
Source
AdvDbg_
SourceCl
ockMSO
xLogicTri
g
-1, 1, 2, 3, 4 Identifies the source of the
Clock for eye diagram tests
using MSOX Logic input.
Confgure Clocking
Method
Clocking
Method
1, 2 This option is used to select
the clocking method used in
the selected PUT(under the
Command and Address
Timing tests section). The
clocking method is typically
determined by the memory
controller where it could use
"1T Timing" or "2T Timing"
method on the address and
command buses. This
clocking method option will
ONLY affect tIS and
tIS(derate) tests.
Confgure DQ to
DQS
phase
shift for
Read(%)
Read_Ph
ase
(Accepts user-defined text), 20 This setting allow user to
modify the expected phase
shift of DQ-DQS for specific
case. The number represent
the % of phase shift expected
for Read cycle.
Confgure DQ to
DQS
phase
shift for
Write(%)
Write_Ph
ase
(Accepts user-defined text), 40 This setting allow user to
modify the expected phase
shift of DQ-DQS for specific
case. The number represent
the % of phase shift expected
for Write cycle.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
20 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Data
Lane
AdvDbgI
nputData
MSOxLo
gicTrig
DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, DQ7, DQ8,
DQ9, DQ10, DQ11, DQ12, DQ13, DQ14, DQ15, DQ16,
DQ17, DQ18, DQ19, DQ20, DQ21, DQ22, DQ23, DQ24,
DQ25, DQ26, DQ27, DQ28, DQ29, DQ30, DQ31, DQ32,
DQ33, DQ34, DQ35, DQ36, DQ37, DQ38, DQ39, DQ40,
DQ41, DQ42, DQ43, DQ44, DQ45, DQ46, DQ47, DQ48,
DQ49, DQ50, DQ51, DQ52, DQ53, DQ54, DQ55, DQ56,
DQ57, DQ58, DQ59, DQ60, DQ61, DQ62, DQ63, DQ64,
DQ65, DQ66, DQ67, DQ68, DQ69, DQ70, DQ71
Identifies the Data lane for
the eye diagram tests using
MSOX Logic input.
Confgure Data
Lane
AdvDbgI
nput_Eye
DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, DQ7, DQ8,
DQ9, DQ10, DQ11, DQ12, DQ13, DQ14, DQ15, DQ16,
DQ17, DQ18, DQ19, DQ20, DQ21, DQ22, DQ23, DQ24,
DQ25, DQ26, DQ27, DQ28, DQ29, DQ30, DQ31, DQ32,
DQ33, DQ34, DQ35, DQ36, DQ37, DQ38, DQ39, DQ40,
DQ41, DQ42, DQ43, DQ44, DQ45, DQ46, DQ47, DQ48,
DQ49, DQ50, DQ51, DQ52, DQ53, DQ54, DQ55, DQ56,
DQ57, DQ58, DQ59, DQ60, DQ61, DQ62, DQ63, DQ64,
DQ65, DQ66, DQ67, DQ68, DQ69, DQ70, DQ71
Identifies the data lane for
the eye diagram tests.
Confgure Data
Source
AdvDbg_
Source1
1, 2, 3, 4 Identifies the source of the
data to be analyzed for eye
diagram tests.
Confgure Data
Source
AdvDbg_
SourceD
ataMSOx
LogicTrig
1, 2, 3, 4 Identifies the source of the
Data for eye diagram tests
using MSOX Logic input.
Confgure Data
Strobe
Lane
AdvDbgS
upport
DQS0, DQS1, DQS2, DQS3, DQS4, DQS5, DQS6,
DQS7, DQS8
Identifies the data strobe
lane for the eye diagram
tests.
Confgure Data
Strobe
Lane
AdvDbgS
upportStr
obeMSO
xLogicTri
g
DQS0, DQS1, DQS2, DQS3, DQS4, DQS5, DQS6,
DQS7, DQS8
Identifies the Data Strobe
lane for the eye diagram tests
using MSOX Logic input.
Confgure Data
Strobe
Source
AdvDbg_
Source2
-1, 1, 2, 3, 4 Identifies the source of the
data strobe for eye diagram
tests.
Confgure Data
Strobe
Source
AdvDbg_
SourceSt
robeMSO
xLogicTri
g
-1, 1, 2, 3, 4 Identifies the source of the
Data Strobe for eye diagram
tests using MSOX Logic
input.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 21

Confgure Data
Transfer
Cycle
EyeDiagr
amOpt
R, W Select Data Transfer Cycle
For Eye Diagram Test
Confgure Debug
Info
Logging
EnableDe
bugLoggi
ng
0, 1 This option enables/disables
additional debug information
logging during test run. This
option is ONLY used for
internal debugging purposes
and should not be enable
during normal test run.
Confgure Derated
Limit
Method
DeratedL
imitMeth
od
0, 1 This option is used to select
the method to determine the
derating values used in
calculation of the dynamic
test limit for tests that
support derating
[tDS-Diff(derate),tDH-Diff(der
ate),tIS(derate),tIH(derate)].
When the "Nominal Method"
option is selected, the
nominal slew rates of the
relevant test signals(DQ or
ADD/CMD) will be used to
determine the derating value.
Otherwise if "Tangent
Method" option is selected,
the slew rates of a tangent
line to the actual test
signals(DQ or ADD/CMD)
will be used to determine the
derating value instead.
Confgure Edge
Type for
HoldTime
measure
ments
CAEdgeO
fInterest
_HoldTi
me
0, 1, 2 This option is used to select
the type of CA signal edge
(Rising/Falling/Both) that
will be processed when
performing the hold time
measurements for Command
and Address Timing tests
section. This option will
ONLY affect tIH and
tIH(derate) tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
22 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Edge
Type for
SetupTim
e
measure
ments
CAEdgeO
fInterest
_SetupTi
me
0, 1, 2 This option is used to select
the type of CA signal edge
(Rising/Falling/Both) that
will be processed when
performing the setup time
measurements for Command
and Address Timing tests
section. This option will
ONLY affect tIS and
tIS(derate) tests.
Confgure Fixed
Burst
Length
FixBurstL
en_Timin
g
4, 8 This value is used ONLY
when the "Rank Separation"
option is enabled. The value
is used in the process to
identify and eliminate bubble
states(if any) from a valid
back-to-back data burst
found when performing the
Data Strobe Timing and Data
Timing tests. For example,
when this value is set to '8',
all the data burst that has
more than 8 data bit long will
be scan for any bubble states
within the data burst. It is
assume that all the multiple
data bursts will have the
same fixed data length(in this
example, 8 data bit). User can
select from the available
values for this option.
Confgure Fixed
Burst
Length
FixedBur
stLength
_LogicM
SOx
NA, 4, 8 This value is to define the Fix
Burst Length of sub-burst.
The value is used to
determine the continuity of
the sub-burst to the next
sub-burst according to the
Logic Pattern.
Confgure Lower
Threshol
d (V)
Chan1_L
ow_Thre
sh
(Accepts user-defined text), -0.50 Specify the lower
measurement threshold used
for Channel 1. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 23

Confgure Lower
Threshol
d (V)
Chan2_L
ow_Thre
sh
(Accepts user-defined text), -0.50 Specify the lower
measurement threshold used
for Channel 2. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Lower
Threshol
d (V)
Chan3_L
ow_Thre
sh
(Accepts user-defined text), 0.680 Specify the lower
measurement threshold used
for Channel 3. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Lower
Threshol
d (V)
Chan4_L
ow_Thre
sh
(Accepts user-defined text), 0.680 Specify the lower
measurement threshold used
for Channel 4. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Mark
Worst
Case
Cycles
MarkWor
stCaseCy
cles
true, false Places markers around the
worst case cycles
(test-dependent). Slows
runtime performance.
Confgure Max
Acqusitio
n Count
MaxAcq
Count
(Accepts user-defined text), 5, 10, 20, 50 Determine the maximum
number of acquisition that
the app will used to try and
achieved the required
READ/WRITE measurement
burst count(as specified in
the "Multi Burst Count"
option) when performing the
tests. *Note: This option is
applicable to all READ
/WRITE burst related tests in
the Electrical Tests group and
Timing Tests group.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
24 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Max
Measure
ment
Count
MaxNum
OfEdgeC
ount
(Accepts user-defined text), 1, 10, 100, 1000 Determine the maximum
number of measurement
edge count (including both
rising and falling edges of the
selected Command and
Address signal) that the app
will used when performing
the Command and Address
Timing Tests(tIS, tIH, etc)
Confgure Middle
Threshol
d (V)
Chan1_
Mid_Thr
esh
(Accepts user-defined text), 0.00 Specify the middle
measurement threshold used
for Channel 1. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Middle
Threshol
d (V)
Chan2_
Mid_Thr
esh
(Accepts user-defined text), 0.00 Specify the middle
measurement threshold used
for Channel 2. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Middle
Threshol
d (V)
Chan3_
Mid_Thr
esh
(Accepts user-defined text), 0.800 Specify the middle
measurement threshold used
for Channel 3. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Middle
Threshol
d (V)
Chan4_
Mid_Thr
esh
(Accepts user-defined text), 0.800 Specify the middle
measurement threshold used
for Channel 4. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 25

Confgure Minimu
m Data
Amplitud
e
DataVolt
Range
(Accepts user-defined text), 0.5 Determine the minimum
amplitude of a Data burst
(DQ/DM) that can be
identified as a valid
READ/WRITE burst data. If
the actual amplitude of a
burst data is lower than the
value specified in this option,
then that particular burst
data will be ignored.
Confgure Multi
Burst
Count
MultiBur
stCount
(Accepts user-defined text), 1, 10, 100, 1000 Determine the number of
READ/WRITE measurement
burst(s) that is required when
performing the tests. *Note:
This option is applicable to all
READ /WRITE burst related
tests in the Electrical Tests
group and Timing Tests group
with the exception of
VOH(AC), VOH(DC), VOL(AC),
VOL(DC), VIHDiff(AC),
VILDiff(AC), VOHDiff(AC) and
VOLDiff(AC) tests.
Confgure OfflineDa
taFolder(
Must be
hidden)
OfflineDa
taFolder
(Accepts user-defined text), C:\ For supporting offline.
Confgure OfflineDa
taMode(
Must be
hidden)
OfflineDa
taMode
(Accepts user-defined text), 0.0, 1.0 For supporting offline
Confgure Option TypeOfSi
gnalCH1
_CAT
NA, PUT, SP, LP_NA, LP_PUT, LP_SP Identifies the signal to use
for Chanel 1 Command and
Address Timing Test.
Confgure Option TypeOfSi
gnalCH2
_CAT
NA, PUT, SP, LP_NA, LP_PUT, LP_SP Identifies the signal to use
for Channel 2 Command and
Address Timing Test.
Confgure Option TypeOfSi
gnalCH3
_CAT
NA, PUT, SP, LP_NA, LP_PUT, LP_SP Identifies the signal to use
for Channel 3 Command and
Address Timing Test.
Confgure Option TypeOfSi
gnalCH4
_CAT
NA, PUT, SP, LP_NA, LP_PUT, LP_SP Identifies the signal to use
for Channel 4 Command and
Address Timing Test.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
26 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure PUT
Source
ElecDiffC
KVihVilP
ut_Sourc
e
1, 2, 3, 4 Identifies the source of the
PUT for Differential
VIHdiff.CK/ VILdiff.CK tests.
Confgure PUT
Source
ElecDiffD
QSVihVil
Put_Sour
ce
1, 2, 3, 4 Identifies the source of the
PUT for Differential
VIHdiff.DQS/ VILdiff.DQS
tests.
Confgure PUT
Source
ElecDiffO
utputPut
_Source
1, 2, 3, 4 Identifies the source of the
PUT for Differential AC
Output Tests.
Confgure PUT
Source
ElecSEVs
ehVselCl
ockPut_
Source
1, 2, 3, 4 Identifies the source of the
PUT for VSEH/VSEL Tests for
Clock.
Confgure PUT
Source
ElecSEVs
ehVselSt
robePut_
Source
1, 2, 3, 4 Identifies the source of the
PUT for VSEH/VSEL Tests for
Strobe.
Confgure PUT
Source
ElecSE_S
ource1
1, 2, 3, 4 Identifies the source of the
PUT for "VOH/VOL and
Output Slew Rate tests" test
group.
Confgure PUT
Source
ElecSE_S
ource1_C
A
1, 2, 3, 4 Identifies the source channel
of the PUT for "VIH/VIL for
Command and Address" test
group.
Confgure PUT
Source
ElecSE_S
ource1_
DQ
1, 2, 3, 4 Identifies the source channel
of the PUT for "VIH/VIL for
DQ and DM" test group.
Confgure PUT
Source
OvrShtSe
CA_LP_S
ource
1, 2, 3, 4 Identifies the source channel
of the PUT for
Overshoot/Undershoot
(Address, Control, Clock,
Chip Select, Clock Enable)
tests.
Confgure PUT
Source
OvrShtSe
DQ_LP_S
ource
1, 2, 3, 4 Identifies the source channel
of the PUT for
Overshoot/Undershoot
(Data, Strobe, Mask) tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 27

Confgure PUT
Source
OvrShtSe
_Source
1, 2, 3, 4 Identifies the source channel
of the PUT for
Overshoot/Undershoot
(Address, Control) tests.
Confgure PUT
Source
OvrShtSe
_Source2
1, 2, 3, 4 Identifies the source channel
of the PUT for
Overshoot/Undershoot
(Data, Strobe, Mask) tests.
Confgure PUT
Source
OvrShtSe
_Source3
1, 2, 3, 4 Identifies the source channel
of the PUT for
Overshoot/Undershoot
(Clock) tests.
Confgure PUT(+)
Source
ElecDIFF
_Source1
1, 2, 3, 4 Identifies the source channel
of the PUT(+) for Differential
AC Input Tests.
Confgure PUT(+)
Source
ElecDiffV
ixCaPutS
ourcePlu
s
1, 2, 3, 4 Identifies the source of the
PUT(+) for VIXCA Test.
Confgure PUT(+)
Source
ElecDiffV
ixDqPutS
ourcePlu
s
1, 2, 3, 4 Identifies the source of the
PUT(-) for VIXDQ Test.
Confgure PUT(-)
Source
ElecDIFF
_Source2
1, 2, 3, 4 Identifies the source channel
of the PUT(-) for Differential
AC Input Tests.
Confgure PUT(-)
Source
ElecDiffV
ixCaPutS
ourceMi
nus
1, 2, 3, 4 Identifies the source of the
PUT(-) for VIXCA Test.
Confgure PUT(-)
Source
ElecDiffV
ixDqPutS
ourceMi
nus
1, 2, 3, 4 Identifies the source of the
PUT(-) for VIXDQ Test.
Confgure Pin
Under
Test, PUT
ElecDiffC
KVihVilP
ut
Clock_DCK0, Clock_DCK1, Clock_DCK2,
LP_Clock_DCK
Identifies the Pin Under Test
for Differential VIHdiff.CK/
VILdiff.CK tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
28 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Pin
Under
Test, PUT
ElecDiffD
QSVihVil
Put
Strobe_DDQS0, Strobe_DDQS1, Strobe_DDQS2,
Strobe_DDQS3, Strobe_DDQS4, Strobe_DDQS5,
Strobe_DDQS6, Strobe_DDQS7, Strobe_DDQS8,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3
Identifies the Pin Under Test
for Differential VIHdiff.DQS/
VILdiff.DQS tests.
Confgure Pin
Under
Test, PUT
ElecDiffV
ixDqPut
Strobe_DDQS0, Strobe_DDQS1, Strobe_DDQS2,
Strobe_DDQS3, Strobe_DDQS4, Strobe_DDQS5,
Strobe_DDQS6, Strobe_DDQS7, Strobe_DDQS8
Identifies the Pin Under Test
for VIXDQ Test.
Confgure Pin
Under
Test, PUT
ElecPara
mDiInput
Clock_DCK0, Clock_DCK1, Clock_DCK2,
Strobe_DDQS0, Strobe_DDQS1, Strobe_DDQS2,
Strobe_DDQS3, Strobe_DDQS4, Strobe_DDQS5,
Strobe_DDQS6, Strobe_DDQS7, Strobe_DDQS8
Identifies the Pin Under Test
for Differential AC Input Tests
parameters.
Confgure Pin
Under
Test, PUT
ElecPara
mDiffOut
put
Strobe_DDQS0, Strobe_DDQS1, Strobe_DDQS2,
Strobe_DDQS3, Strobe_DDQS4, Strobe_DDQS5,
Strobe_DDQS6, Strobe_DDQS7, Strobe_DDQS8,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3
Identifies the Pin Under Test
for Differential AC output
parameters.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 29

Confgure Pin
Under
Test, PUT
ElecPara
mSeInpu
t
Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71,
Strobe_SDQS0, Strobe_SDQS1, Strobe_SDQS2,
Strobe_SDQS3, Strobe_SDQS4, Strobe_SDQS5,
Strobe_SDQS6, Strobe_SDQS7, Strobe_SDQS8,
LP_Data_DQ0, LP_Data_DQ1, LP_Data_DQ2,
LP_Data_DQ3, LP_Data_DQ4, LP_Data_DQ5,
LP_Data_DQ6, LP_Data_DQ7, LP_Data_DQ8,
LP_Data_DQ9, LP_Data_DQ10, LP_Data_DQ11,
LP_Data_DQ12, LP_Data_DQ13, LP_Data_DQ14,
LP_Data_DQ15, LP_Data_DQ16, LP_Data_DQ17,
LP_Data_DQ18, LP_Data_DQ19, LP_Data_DQ20,
LP_Data_DQ21, LP_Data_DQ22, LP_Data_DQ23,
LP_Data_DQ24, LP_Data_DQ25, LP_Data_DQ26,
LP_Data_DQ27, LP_Data_DQ28, LP_Data_DQ29,
LP_Data_DQ30, LP_Data_DQ31,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3
Identifies the Pin Under Test
for "VOH/VOL and Output
Slew Rate tests" test group.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
30 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Pin
Under
Test, PUT
ElecPara
mSeInpu
t_CA
Control_NRAS, Control_NWE, Control_NCAS,
Control_NCS0, Control_NCS1, Control_CKE0,
Control_CKE1, Control_ODT0, Control_ODT1,
Address_A0, Address_A1, Address_A2,
Address_A3, Address_A4, Address_A5,
Address_A6, Address_A7, Address_A8,
Address_A9, Address_A10, Address_A11,
Address_A12, Address_A13, Address_A14,
Address_A15, Control_BA0, Control_BA1,
Control_BA2, LP_CommandAddress_CA0,
LP_CommandAddress_CA1,
LP_CommandAddress_CA2,
LP_CommandAddress_CA3,
LP_CommandAddress_CA4,
LP_CommandAddress_CA5,
LP_CommandAddress_CA6,
LP_CommandAddress_CA7,
LP_CommandAddress_CA8,
LP_CommandAddress_CA9, LP_Control_NCS
Identifies the Pin Under Test
for "VIH/VIL for Command
and Address" test group.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 31

Confgure Pin
Under
Test, PUT
ElecPara
mSeInpu
t_DQ
Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71,
DM_DM0, DM_DM1, DM_DM2, DM_DM3,
DM_DM4, DM_DM5, DM_DM6, DM_DM7,
LP_Data_DQ0, LP_Data_DQ1, LP_Data_DQ2,
LP_Data_DQ3, LP_Data_DQ4, LP_Data_DQ5,
LP_Data_DQ6, LP_Data_DQ7, LP_Data_DQ8,
LP_Data_DQ9, LP_Data_DQ10, LP_Data_DQ11,
LP_Data_DQ12, LP_Data_DQ13, LP_Data_DQ14,
LP_Data_DQ15, LP_Data_DQ16, LP_Data_DQ17,
LP_Data_DQ18, LP_Data_DQ19, LP_Data_DQ20,
LP_Data_DQ21, LP_Data_DQ22, LP_Data_DQ23,
LP_Data_DQ24, LP_Data_DQ25, LP_Data_DQ26,
LP_Data_DQ27, LP_Data_DQ28, LP_Data_DQ29,
LP_Data_DQ30, LP_Data_DQ31, LP_DM_DM0,
LP_DM_DM1, LP_DM_DM2, LP_DM_DM3
Identifies the Pin Under Test
for "VIH/VIL for DQ and DM"
test group.
Confgure Pin
Under
Test, PUT
ElecSEVs
ehVselCl
ockPut
Clock_SCK0, Clock_SCK1, Clock_SCK2,
Clock_NCK0, Clock_NCK1, Clock_NCK2,
LP_Clock_SCK, LP_Clock_NCK
Identifies the Pin Under Test
for VSEH/VSEL Tests for
Clock.
Confgure Pin
Under
Test, PUT
ElecSEVs
ehVselSt
robePut
Strobe_SDQS0, Strobe_SDQS1, Strobe_SDQS2,
Strobe_SDQS3, Strobe_SDQS4, Strobe_SDQS5,
Strobe_SDQS6, Strobe_SDQS7, Strobe_SDQS8,
Strobe_NDQS0, Strobe_NDQS1, Strobe_NDQS2,
Strobe_NDQS3, Strobe_NDQS4, Strobe_NDQS5,
Strobe_NDQS6, Strobe_NDQS7, Strobe_NDQS8,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3
Identifies the Pin Under Test
for VSEH/VSEL Tests for
Strobe.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
32 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Pin
Under
Test, PUT
OvrShtSe
CA_LP_I
nput
CKE, CS_n, ODT, CA0, CA1, CA2, CA3, CA4, CA5,
CA6, CA7, CA8, CA9, CK_t, CK_c
Identifies the Pin Under Test
for Overshoot/Undershoot
(Address, Control, Clock,
Chip Select, Clock Enable)
parameters.
Confgure Pin
Under
Test, PUT
OvrShtSe
DQ_LP_I
nput
DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, DQ7, DQ8,
DQ9, DQ10, DQ11, DQ12, DQ13, DQ14, DQ15, DQ16,
DQ17, DQ18, DQ19, DQ20, DQ21, DQ22, DQ23, DQ24,
DQ25, DQ26, DQ27, DQ28, DQ29, DQ30, DQ31,
DQS0_t, DQS1_t, DQS2_t, DQS3_t, DQS0_c,
DQS1_c, DQS2_c, DQS3_c, DM0, DM1, DM2, DM3
Identifies the Pin Under Test
for Overshoot/Undershoot
(Data, Strobe, Mask)
parameters.
Confgure Pin
Under
Test, PUT
OvrShtSe
Input
/RAS, /WE, /CAS, /CS0, /CS1, CKE0, CKE1, ODT0,
ODT1, A0, A1, A2, A3, A4, A5, A6, A7, A8, A9, A10,
A11, A12, A13, A14, A15, BA0, BA1, BA2
Identifies the Pin Under Test
for Overshoot/Undershoot
(Address, Control)
parameters.
Confgure Pin
Under
Test, PUT
OvrShtSe
Input2
DQ0, DQ1, DQ2, DQ3, DQ4, DQ5, DQ6, DQ7, DQ8,
DQ9, DQ10, DQ11, DQ12, DQ13, DQ14, DQ15, DQ16,
DQ17, DQ18, DQ19, DQ20, DQ21, DQ22, DQ23, DQ24,
DQ25, DQ26, DQ27, DQ28, DQ29, DQ30, DQ31, DQ32,
DQ33, DQ34, DQ35, DQ36, DQ37, DQ38, DQ39, DQ40,
DQ41, DQ42, DQ43, DQ44, DQ45, DQ46, DQ47, DQ48,
DQ49, DQ50, DQ51, DQ52, DQ53, DQ54, DQ55, DQ56,
DQ57, DQ58, DQ59, DQ60, DQ61, DQ62, DQ63, DQ64,
DQ65, DQ66, DQ67, DQ68, DQ69, DQ70, DQ71, DQS0,
DQS1, DQS2, DQS3, DQS4, DQS5, DQS6, DQS7,
DQS8, DQS0/, DQS1/, DQS2/, DQS3/, DQS4/,
DQS5/, DQS6/, DQS7/, DQS8/, DM0, DM1, DM2,
DM3, DM4, DM5, DM6, DM7
Identifies the Pin Under Test
for Overshoot/Undershoot
(Data, Strobe, Mask)
parameters.
Confgure Pin
Under
Test, PUT
OvrShtSe
Input3
CK0, CK1, CK2, /CK0, /CK1, /CK2 Identifies the Pin Under Test
for Overshoot/Undershoot
(Clock) parameters.
Confgure Pin
Under
Test, PUT
TypeOfSi
gnalCH2
NA, Clock, Strobe, Data, DM, Control, LP_NA,
LP_Clock, LP_Strobe, LP_Data, LP_DM, LP_Control
Identifies the signal to use
for Channel2 timing test.
Confgure Pin
Under
Test, PUT
TypeOfSi
gnalCH3
NA, Clock, Strobe, Data, DM, Control, LP_NA,
LP_Clock, LP_Strobe, LP_Data, LP_DM, LP_Control
Identifies the signal to use
for Channel3 timing test.
Confgure Pin
Under
Test, PUT
TypeOfSi
gnalCH4
NA, Clock, Strobe, Data, DM, Control, LP_NA,
LP_Clock, LP_Strobe, LP_Data, LP_DM, LP_Control
Identifies the signal to use
for Channel4 timing test.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 33

Confgure Pin
Under
Test, PUT
Paramet
ers for
Channel
1
TypeOfSi
gnalCH1
NA, Clock, Strobe, Data, DM, Control, LP_NA,
LP_Clock, LP_Strobe, LP_Data, LP_DM, LP_Control
Identifies the signal to use
for Channel 1 timing tests.
Confgure RAS
Channel
RASDigC
hannel
DIGital0, DIGital1, DIGital2, DIGital3, DIGital4,
DIGital5, DIGital6, DIGital7, DIGital8, DIGital9,
DIGital10, DIGital11, DIGital12, DIGital13, DIGital14,
DIGital15
Identifies the channel source
selection of the RAS digital
signal to be analyzed for
MSOx Logic Triggering.
Confgure READ
Latency
ReadLate
ncy
1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0,
13.0, 14.0, 15.0, 16.0, 17.0, 18.0, 19.0, 20.0
This value is used ONLY
when the "Rank Separation"
option is enabled. This allow
user to specify the overall
Read latency(RL) value to be
used in performing the Data
Strobe Timing and Data
Timing tests when the "Rank
Separation" option is
enabled. By definition, the
Read Latency (RL) = Additive
Latency (AL) + CAS Latency
(CL); RL = AL + CL.
Confgure READ
Latency
Value
RLValue 1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0,
13.0, 14.0, 15.0, 16.0, 17.0, 18.0, 19.0, 20.0
This value is used ONLY
when the "Rank Separation"
option is enabled. This allow
user to specify the overall
Read latency(RL) value to be
used in generating the READ
eye diagram when the "Rank
Separation" option is
enabled. By definition, the
Read Latency (RL) = Additive
Latency (AL) + CAS Latency
(CL); RL = AL + CL.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
34 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Rank
Separatio
n
CSDQSC
YC
0.0, 1.0 Enable/disable the rank
separation option when
running the Data Strobe
Timing and Data Timing
tests. When this option is
enabled, an additional
channel for Chip Select(CS)
signal will be required.
Measurements will only be
done on selected Rank based
on the Chip Select signal
connected to the
oscilloscope. This Rank
Separation mode is also used
to handle a valid
back-to-back data burst
found when running the
selected Data Strobe Timing
and Data Timing tests. The
bubble states(if any) that
exist during a valid
back-to-back data burst will
be identified and ignored
based on the Chip Select
signal with reference to the
"READ/WRITE Latency" and
"Fix Burst Length" settings.
Confgure Rank
Separatio
n
RankEye
Diagram
Opt
0, 1 Enable/disable the rank
separation option for
generating the READ/WRITE
eye diagram. When this
option is enabled, the eye
diagram generated will be
qualified based on an
additional Chip Select input
signal besides the DQS and
DQ signals. When this option
is disabled, the eye diagram
will be generated based on
DQS and DQ signal ONLY
(Chip Select input will be
ignored).
Confgure Re-scale
Test
Mask
ReScale
Mask
true, false Enable/disable horizontal
re-scaling of selected test
mask to be loaded in the eye
diagram tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 35

Confgure Sampling
Points
(Pts)
Electrical
and
Timing
Tests
Only
Sampling
Points
(Accepts user-defined text), 2000000, 1000000,
500000
Specifies the sampling points
to be captured in all the tests
except Clock Timing tests
and Eye Digram tests.
Reduce the sampling points if
the read/write bursts are
occuring very frequently.
Confgure Sampling
Points
(Pts) Eye
Diagram
Tests
using
MSOx
Logic
Triggerin
g
Sampling
PointsLy
nxEyeDia
gram
(Accepts user-defined text), 8000000, 2000000,
1000000
Specifies the sampling points
to be captured in Eye
Diagram Test which using
MSOx Logic Triggering.
Reduce the sampling points if
the read/write bursts are
occuring very frequently.
Confgure Signal
selected
MyCH1_
CAT
NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2,
Control_NCS0, Control_NCS1, Control_BA0,
Control_BA1, Control_BA2, Control_NRAS,
Control_NWE, Control_NCAS, Control_CKE0,
Control_CKE1, Control_ODT0, Control_ODT1,
Address_A0, Address_A1, Address_A2,
Address_A3, Address_A4, Address_A5,
Address_A6, Address_A7, Address_A8,
Address_A9, Address_A10, Address_A11,
Address_A12, Address_A13, Address_A14,
Address_A15, LP_Clock_DCK, LP_Clock_SCK,
LP_Control_NCS, LP_Control_CKE,
LP_CommandAddress_CA0,
LP_CommandAddress_CA1,
LP_CommandAddress_CA2,
LP_CommandAddress_CA3,
LP_CommandAddress_CA4,
LP_CommandAddress_CA5,
LP_CommandAddress_CA6,
LP_CommandAddress_CA7,
LP_CommandAddress_CA8,
LP_CommandAddress_CA9
Please select the signal
parameter connected to
Channel 1 for Command and
Address Timing tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
36 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Signal
selected
MyCH2_
CAT
NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2,
Control_NCS0, Control_NCS1, Control_BA0,
Control_BA1, Control_BA2, Control_NRAS,
Control_NWE, Control_NCAS, Control_CKE0,
Control_CKE1, Control_ODT0, Control_ODT1,
Address_A0, Address_A1, Address_A2,
Address_A3, Address_A4, Address_A5,
Address_A6, Address_A7, Address_A8,
Address_A9, Address_A10, Address_A11,
Address_A12, Address_A13, Address_A14,
Address_A15, LP_Clock_DCK, LP_Clock_SCK,
LP_Control_NCS, LP_Control_CKE,
LP_CommandAddress_CA0,
LP_CommandAddress_CA1,
LP_CommandAddress_CA2,
LP_CommandAddress_CA3,
LP_CommandAddress_CA4,
LP_CommandAddress_CA5,
LP_CommandAddress_CA6,
LP_CommandAddress_CA7,
LP_CommandAddress_CA8,
LP_CommandAddress_CA9
Please select the signal
parameter connected to
Channel 2 for Command and
Address Timing tests.
Confgure Signal
selected
MyCH3_
CAT
NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2,
Control_NCS0, Control_NCS1, Control_BA0,
Control_BA1, Control_BA2, Control_NRAS,
Control_NWE, Control_NCAS, Control_CKE0,
Control_CKE1, Control_ODT0, Control_ODT1,
Address_A0, Address_A1, Address_A2,
Address_A3, Address_A4, Address_A5,
Address_A6, Address_A7, Address_A8,
Address_A9, Address_A10, Address_A11,
Address_A12, Address_A13, Address_A14,
Address_A15, LP_Clock_DCK, LP_Clock_SCK,
LP_Control_NCS, LP_Control_CKE,
LP_CommandAddress_CA0,
LP_CommandAddress_CA1,
LP_CommandAddress_CA2,
LP_CommandAddress_CA3,
LP_CommandAddress_CA4,
LP_CommandAddress_CA5,
LP_CommandAddress_CA6,
LP_CommandAddress_CA7,
LP_CommandAddress_CA8,
LP_CommandAddress_CA9
Please select the signal
parameter connected to
Channel 3 for Command and
Address Timing tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 37

Confgure Signal
selected
MyCH4_
CAT
NA_, Clock_DCK0, Clock_DCK1, Clock_DCK2,
Clock_SCK0, Clock_SCK1, Clock_SCK2,
Control_NCS0, Control_NCS1, Control_BA0,
Control_BA1, Control_BA2, Control_NRAS,
Control_NWE, Control_NCAS, Control_CKE0,
Control_CKE1, Control_ODT0, Control_ODT1,
Address_A0, Address_A1, Address_A2,
Address_A3, Address_A4, Address_A5,
Address_A6, Address_A7, Address_A8,
Address_A9, Address_A10, Address_A11,
Address_A12, Address_A13, Address_A14,
Address_A15, LP_Clock_DCK, LP_Clock_SCK,
LP_Control_NCS, LP_Control_CKE,
LP_CommandAddress_CA0,
LP_CommandAddress_CA1,
LP_CommandAddress_CA2,
LP_CommandAddress_CA3,
LP_CommandAddress_CA4,
LP_CommandAddress_CA5,
LP_CommandAddress_CA6,
LP_CommandAddress_CA7,
LP_CommandAddress_CA8,
LP_CommandAddress_CA9
Please select the signal
parameter connected to
Channel 4 for Command and
Address Timing tests.
Confgure Skip
Connecti
on
Diagram
Prompt
EnableCo
nnection
Prompt
1, 0 By selecting "No", system
will prompt for required
connection diagram change
when running selected tests.
By selecting "Yes", system
will NOT prompt for any
connection diagram change
when running the selected
tests. This option is used to
enable continuous running of
tests from different test
groups (that may require
different scope connections)
without having to respond to
a pop-up connection diagram
change. However, user are
expected to be responsible of
ensuring the correct scope
connections that will be used
for running all selected tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
38 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Skip
Error
Message
ErrorMsg
Off
1, 0 By selecting "No", system
will prompt error message.
By selecting "Yes", system
will bypass all error message
that occur and continue to
next test. The test result for
those tests that encounter
errors will be set to a default
invalid value that would
cause a failure. Hint: This is
useful when the user wants
to run multiple trials
overnight.
Confgure Supporti
ng Pin
ElecDiffD
QSVihVil
Support
Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71,
LP_Data_DQ0, LP_Data_DQ1, LP_Data_DQ2,
LP_Data_DQ3, LP_Data_DQ4, LP_Data_DQ5,
LP_Data_DQ6, LP_Data_DQ7, LP_Data_DQ8,
LP_Data_DQ9, LP_Data_DQ10, LP_Data_DQ11,
LP_Data_DQ12, LP_Data_DQ13, LP_Data_DQ14,
LP_Data_DQ15, LP_Data_DQ16, LP_Data_DQ17,
LP_Data_DQ18, LP_Data_DQ19, LP_Data_DQ20,
LP_Data_DQ21, LP_Data_DQ22, LP_Data_DQ23,
LP_Data_DQ24, LP_Data_DQ25, LP_Data_DQ26,
LP_Data_DQ27, LP_Data_DQ28, LP_Data_DQ29,
LP_Data_DQ30, LP_Data_DQ31
Identifies the required
supporting pin for Differential
VIHdiff.DQS/ VILdiff.DQS
tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 39

Confgure Supporti
ng Pin
ElecDiffV
ixDqSupp
ortPin
Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71
Identifies the supporting pin
for VIXDQ Test.
Confgure Supporti
ng Pin
ElecPara
mDiSupp
ort
N/A, Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71
Identifies the supporting pin
for Differential AC Input Tests
parameters.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
40 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Supporti
ng Pin
ElecPara
mDiffOut
putSupp
ort
Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71,
LP_Data_DQ0, LP_Data_DQ1, LP_Data_DQ2,
LP_Data_DQ3, LP_Data_DQ4, LP_Data_DQ5,
LP_Data_DQ6, LP_Data_DQ7, LP_Data_DQ8,
LP_Data_DQ9, LP_Data_DQ10, LP_Data_DQ11,
LP_Data_DQ12, LP_Data_DQ13, LP_Data_DQ14,
LP_Data_DQ15, LP_Data_DQ16, LP_Data_DQ17,
LP_Data_DQ18, LP_Data_DQ19, LP_Data_DQ20,
LP_Data_DQ21, LP_Data_DQ22, LP_Data_DQ23,
LP_Data_DQ24, LP_Data_DQ25, LP_Data_DQ26,
LP_Data_DQ27, LP_Data_DQ28, LP_Data_DQ29,
LP_Data_DQ30, LP_Data_DQ31
Identifies the required
supporting pin for Differential
AC output parameters.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 41

Confgure Supporti
ng Pin
ElecPara
mSeSupp
ort
Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71,
Strobe_DDQS0, Strobe_DDQS1, Strobe_DDQS2,
Strobe_DDQS3, Strobe_DDQS4, Strobe_DDQS5,
Strobe_DDQS6, Strobe_DDQS7, Strobe_DDQS8,
Strobe_SDQS0, Strobe_SDQS1, Strobe_SDQS2,
Strobe_SDQS3, Strobe_SDQS4, Strobe_SDQS5,
Strobe_SDQS6, Strobe_SDQS7, Strobe_SDQS8,
LP_Data_DQ0, LP_Data_DQ1, LP_Data_DQ2,
LP_Data_DQ3, LP_Data_DQ4, LP_Data_DQ5,
LP_Data_DQ6, LP_Data_DQ7, LP_Data_DQ8,
LP_Data_DQ9, LP_Data_DQ10, LP_Data_DQ11,
LP_Data_DQ12, LP_Data_DQ13, LP_Data_DQ14,
LP_Data_DQ15, LP_Data_DQ16, LP_Data_DQ17,
LP_Data_DQ18, LP_Data_DQ19, LP_Data_DQ20,
LP_Data_DQ21, LP_Data_DQ22, LP_Data_DQ23,
LP_Data_DQ24, LP_Data_DQ25, LP_Data_DQ26,
LP_Data_DQ27, LP_Data_DQ28, LP_Data_DQ29,
LP_Data_DQ30, LP_Data_DQ31,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3
Identifies the required
supporting pin for "VOH/VOL
and Output Slew Rate tests"
test group.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
42 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Supporti
ng Pin
ElecPara
mSeSupp
ort_DQ
Strobe_DDQS0, Strobe_DDQS1, Strobe_DDQS2,
Strobe_DDQS3, Strobe_DDQS4, Strobe_DDQS5,
Strobe_DDQS6, Strobe_DDQS7, Strobe_DDQS8,
Strobe_SDQS0, Strobe_SDQS1, Strobe_SDQS2,
Strobe_SDQS3, Strobe_SDQS4, Strobe_SDQS5,
Strobe_SDQS6, Strobe_SDQS7, Strobe_SDQS8,
LP_Strobe_DDQS0, LP_Strobe_DDQS1,
LP_Strobe_DDQS2, LP_Strobe_DDQS3,
LP_Strobe_SDQS0, LP_Strobe_SDQS1,
LP_Strobe_SDQS2, LP_Strobe_SDQS3
Identifies the required
supporting pin for "VIH/VIL
for DQ and DM" test group.
Confgure Supporti
ng Pin
ElecSEVs
ehVselSt
robeSupp
ort
Data_DQ0, Data_DQ1, Data_DQ2, Data_DQ3,
Data_DQ4, Data_DQ5, Data_DQ6, Data_DQ7,
Data_DQ8, Data_DQ9, Data_DQ10, Data_DQ11,
Data_DQ12, Data_DQ13, Data_DQ14, Data_DQ15,
Data_DQ16, Data_DQ17, Data_DQ18, Data_DQ19,
Data_DQ20, Data_DQ21, Data_DQ22, Data_DQ23,
Data_DQ24, Data_DQ25, Data_DQ26, Data_DQ27,
Data_DQ28, Data_DQ29, Data_DQ30, Data_DQ31,
Data_DQ32, Data_DQ33, Data_DQ34, Data_DQ35,
Data_DQ36, Data_DQ37, Data_DQ38, Data_DQ39,
Data_DQ40, Data_DQ41, Data_DQ42, Data_DQ43,
Data_DQ44, Data_DQ45, Data_DQ46, Data_DQ47,
Data_DQ48, Data_DQ49, Data_DQ50, Data_DQ51,
Data_DQ52, Data_DQ53, Data_DQ54, Data_DQ55,
Data_DQ56, Data_DQ57, Data_DQ58, Data_DQ59,
Data_DQ60, Data_DQ61, Data_DQ62, Data_DQ63,
Data_DQ64, Data_DQ65, Data_DQ66, Data_DQ67,
Data_DQ68, Data_DQ69, Data_DQ70, Data_DQ71,
LP_Data_DQ0, LP_Data_DQ1, LP_Data_DQ2,
LP_Data_DQ3, LP_Data_DQ4, LP_Data_DQ5,
LP_Data_DQ6, LP_Data_DQ7, LP_Data_DQ8,
LP_Data_DQ9, LP_Data_DQ10, LP_Data_DQ11,
LP_Data_DQ12, LP_Data_DQ13, LP_Data_DQ14,
LP_Data_DQ15, LP_Data_DQ16, LP_Data_DQ17,
LP_Data_DQ18, LP_Data_DQ19, LP_Data_DQ20,
LP_Data_DQ21, LP_Data_DQ22, LP_Data_DQ23,
LP_Data_DQ24, LP_Data_DQ25, LP_Data_DQ26,
LP_Data_DQ27, LP_Data_DQ28, LP_Data_DQ29,
LP_Data_DQ30, LP_Data_DQ31
Identifies the supporting pin
for VSEH/VSEL Tests for
Strobe.
Confgure Supporti
ng Pin
Source
ElecDIFF
_Source3
-1, 1, 2, 3, 4 Identifies the source channel
of the supporting pin for
Differential AC Input Tests.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 43

Confgure Supporti
ng Pin
Source
ElecDiffD
QSVihVil
Supprt_S
ource
1, 2, 3, 4 Identifies the source of the
supporting pin for Differential
VIHdiff.DQS/ VILdiff.DQS
tests.
Confgure Supporti
ng Pin
Source
ElecDiffO
utputSup
prt_Sour
ce
1, 2, 3, 4 Identifies the source of the
supporting pin for Differential
AC Output Tests.
Confgure Supporti
ng Pin
Source
ElecDiffV
ixDqSupp
ortPinSo
urce
1, 2, 3, 4 Identifies the source of the
supporting pin for VIXDQ
Test.
Confgure Supporti
ng Pin
Source
ElecSEVs
ehVselSt
robeSupp
ort_Sour
ce
1, 2, 3, 4 Identifies the source of the
supporting pin for
VSEH/VSEL Tests for Strobe.
Confgure Supporti
ng Pin
Source
ElecSE_S
ource2
1, 2, 3, 4 Identifies the source of the
supporting pin for "VOH/VOL
and Output Slew Rate tests"
test group.
Confgure Supporti
ng Pin
Source
ElecSE_S
ource2_
DQ
-1, 1, 2, 3, 4 Identifies the source channel
of the supporting pin for
"VIH/VIL for DQ and DM"
test group.
Confgure Threshol
d Mode
ThreshSe
tMode
1, 0 By selecting "TopBaseRatio",
the system will automatically
determine the threshold
settings that are used for the
READ/WRITE burst
triggering and identification
using the TopRatio and
BaseRatio specified for a
particular channel input.
Setting "Custom Threshold"
allows user to directly set the
threshold settings used
instead.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
44 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Top Ratio BurstTrig
gerTopRa
tio_Chan
1
(Accepts user-defined text), 0.80 Specify the value of the top
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Confgure Top Ratio BurstTrig
gerTopRa
tio_Chan
2
(Accepts user-defined text), 0.80 Specify the value of the top
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Confgure Top Ratio BurstTrig
gerTopRa
tio_Chan
3
(Accepts user-defined text), 0.80 Specify the value of the top
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Confgure Top Ratio BurstTrig
gerTopRa
tio_Chan
4
(Accepts user-defined text), 0.80 Specify the value of the top
ratio used when triggering for
the READ/WRITE burst data.
The value set here is
applicable ONLY when the
"Threshold Mode" option is
set to "TopBaseRatio".
Confgure Total Bit
Display(c
ycle)
myDisBit (Accepts user-defined text), 2, 4, 10, 20, 50 This option allows the user to
select how many data bits to
be displayed by end of the
test.More bits selected will
enable user to have a clearer
view of the whole burst of
signals.
Confgure Total
Wavefor
m
EyeDiagr
amNumO
fWave
(Accepts user-defined text), 500, 1000, 1500, 3000,
5000
Select or type the total
number of waveforms
required for eye diagram
tests.
Confgure Trigger
timeout
(ms)
TimeOut
_Complia
nce
(Accepts user-defined text), 5000, 10000, 15000,
20000, 30000
Identifies the trigger time out
value. This represent the
time taken to terminate the
test when the scope unable
to trigger any signal.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 45

Confgure Triggerin
g READ
Latency
Triggerin
gReadLat
ency
1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0,
13.0, 14.0, 15.0, 16.0, 17.0, 18.0, 19.0, 20.0, 21.0, 22.0,
23.0, 24.0, 25.0, 26.0, 27.0, 28.0, 29.0, 30.0, 31.0, 32.0,
33.0, 34.0, 35.0, 36.0, 37.0, 38.0, 39.0, 40.0, 41.0, 42.0,
43.0, 44.0, 45.0, 46.0, 47.0, 48.0, 49.0, 50.0, 51.0, 52.0,
53.0, 54.0, 55.0, 56.0, 57.0, 58.0, 59.0, 60.0, 61.0, 62.0,
63.0, 64.0, 65.0, 66.0, 67.0, 68.0, 69.0, 70.0, 71.0, 72.0,
73.0, 74.0, 75.0, 76.0, 77.0, 78.0, 79.0, 80.0, 81.0, 82.0,
83.0, 84.0, 85.0, 86.0, 87.0, 88.0, 89.0, 90.0, 91.0, 92.0,
93.0, 94.0, 95.0, 96.0, 97.0, 98.0, 99.0, 100.0
This value is used ONLY
when the "Logic Triggering"
option is enabled. This allow
user to specify the overall
Read latency(RL) value to be
used to determine the burst
location from event of Read
Burst logic pattern.
Confgure Triggerin
g WRITE
Latency
Triggerin
gWriteLa
tency
1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0,
13.0, 14.0, 15.0, 16.0, 17.0, 18.0, 19.0, 20.0, 21.0, 22.0,
23.0, 24.0, 25.0, 26.0, 27.0, 28.0, 29.0, 30.0, 31.0, 32.0,
33.0, 34.0, 35.0, 36.0, 37.0, 38.0, 39.0, 40.0, 41.0, 42.0,
43.0, 44.0, 45.0, 46.0, 47.0, 48.0, 49.0, 50.0, 51.0, 52.0,
53.0, 54.0, 55.0, 56.0, 57.0, 58.0, 59.0, 60.0, 61.0, 62.0,
63.0, 64.0, 65.0, 66.0, 67.0, 68.0, 69.0, 70.0, 71.0, 72.0,
73.0, 74.0, 75.0, 76.0, 77.0, 78.0, 79.0, 80.0, 81.0, 82.0,
83.0, 84.0, 85.0, 86.0, 87.0, 88.0, 89.0, 90.0, 91.0, 92.0,
93.0, 94.0, 95.0, 96.0, 97.0, 98.0, 99.0, 100.0
This value is used ONLY
when the "Logic Triggering"
option is enabled. This allow
user to specify the overall
Write latency(WL) value to
be used to determine the
burst location from event of
Write Burst logic pattern.
Confgure Upper
Threshol
d (V)
Chan1_U
p_Thresh
(Accepts user-defined text), 0.50 Specify the upper
measurement threshold used
for Channel 1. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Upper
Threshol
d (V)
Chan2_U
p_Thresh
(Accepts user-defined text), 0.50 Specify the upper
measurement threshold used
for Channel 2. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure Upper
Threshol
d (V)
Chan3_U
p_Thresh
(Accepts user-defined text), 0.920 Specify the upper
measurement threshold used
for Channel 3. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
46 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure Upper
Threshol
d (V)
Chan4_U
p_Thresh
(Accepts user-defined text), 0.920 Specify the upper
measurement threshold used
for Channel 4. The value set
here is applicable ONLY
when the "Threshold Mode"
option is set to "Custom
Threshold".
Confgure User
Defined
Vcent
UserDefi
nedVcent
(Accepts user-defined text), 0.800 Identifies the user defined
Vcent level for shifting of the
tDIVW/vDIVW mask. The
value set here is applicable
ONLY when the "Vcent
Evaluation Mode" option is
set to "User defined Vcent".
Confgure VDD (V) InputVD
D
(Accepts user-defined text), 1.275, 1.200, 1.125 Identifies the input supply
voltage.
Confgure VDDQ (V) InputVD
DQ
(Accepts user-defined text), 1.275, 1.200, 1.125 Identifies the input supply
voltage for data signal.
Confgure VIH.CA_
AC (V)
InputThr
eshold_V
ih_ac_C
A
(Accepts user-defined text), 0.920 Identifies the ac input logic
HIGH voltage for Address and
Command inputs.
Confgure VIH.CA_
DC (V)
InputThr
eshold_V
ih_dc_C
A
(Accepts user-defined text), 0.900 Identifies the dc input logic
HIGH voltage for Address and
Command inputs.
Confgure VIH.DQ_
AC (V)
InputThr
eshold_V
ih_ac_D
Q
(Accepts user-defined text), 0.920 Identifies the ac input logic
HIGH voltage for DQ and DM
inputs.
Confgure VIH.DQ_
DC (V)
InputThr
eshold_V
ih_dc_D
Q
(Accepts user-defined text), 0.900 Identifies the dc input logic
HIGH voltage for DQ and DM
inputs.
Confgure VIHdiff.C
K_AC (V)
VIHdiff_a
c_CK
(Accepts user-defined text), 0.240 Differential input high.
Affects only differential CK
only.
Confgure VIHdiff.D
QS_AC
(V)
VIHdiff_a
c_DQS
(Accepts user-defined text), 0.240 Differential input high.
Affects only differential DQS
only.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 47

Confgure VIHdiff_
min/VIH
diff_DC
(V)
VIHdiff_
min
(Accepts user-defined text), 0.200 Minimum differential input
high. This value is used
solely to define a differential
signal slew rate. Affects only
differential DQS and CK.
Confgure VIL.CA_
AC (V)
InputThr
eshold_V
il_ac_CA
(Accepts user-defined text), 0.680 Identifies the ac input logic
LOW voltage for Address and
Command inputs.
Confgure VIL.CA_
DC (V)
InputThr
eshold_V
il_dc_CA
(Accepts user-defined text), 0.700 Identifies the dc input logic
LOW voltage for Address and
Command inputs.
Confgure VIL.DQ_
AC (V)
InputThr
eshold_V
il_ac_DQ
(Accepts user-defined text), 0.680 Identifies the ac input logic
LOW voltage for DQ and DM
inputs.
Confgure VIL.DQ_
DC (V
InputThr
eshold_V
il_dc_DQ
(Accepts user-defined text), 0.700 Identifies the dc input logic
LOW voltage for DQ and DM
inputs.
Confgure VILdiff.C
K_AC (V)
VILdiff_a
c_CK
(Accepts user-defined text), -0.240 Differential input high.
Affects only differential CK
only.
Confgure VILdiff.D
QS_AC
(V)
VILdiff_a
c_DQS
(Accepts user-defined text), -0.240 Differential input high.
Affects only differential DQS
only.
Confgure VILdiff_
max/VIL
diff_DC
(V)
VILdiff_
max
(Accepts user-defined text), -0.200 Maximum differential input
low. This value is used solely
to define a differential signal
slew rate. Affects only
differential DQS and CK.
Confgure VOH_AC
(V)
InputThr
eshold_V
oh_ac
(Accepts user-defined text), 1.020 Identifies the ac output logic
HIGH voltage.
Confgure VOH_DC
(V)
InputThr
eshold_V
oh_dc
(Accepts user-defined text), 1.32 Identifies the dc output logic
HIGH voltage.
Confgure VOHdiff_
AC (V)
VOHdiff_
ac
(Accepts user-defined text), 0.360 Differential output high.
Affects only differential DQS
only.
Confgure VOL_AC
(V)
InputThr
eshold_V
ol_ac
(Accepts user-defined text), 0.660 Identifies the ac output logic
LOW voltage.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
48 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure VOL_DC
(V)
InputThr
eshold_V
ol_dc
(Accepts user-defined text), 0.600 Identifies the dc output logic
LOW voltage.
Confgure VOLdiff_
AC (V)
VOLdiff_
ac
(Accepts user-defined text), -0.360 Differential output high.
Affects only differential DQS
only.
Confgure VRef
A12-BC
Signal(V)
InputRef
V_VrefA1
2BCLogic
(Accepts user-defined text), NA, 0.735, 0.750, 0.765 Identifies the A12-BC
reference voltage for MSOx
Logic Triggering.
Confgure VRef ACT
Signal(V)
InputRef
V_VrefA
CTLogic
(Accepts user-defined text), 0.735, 0.750, 0.765 Identifies the ACT reference
voltage for MSOx Logic
Triggering.
Confgure VRef
CAS
Signal(V)
InputRef
V_VrefC
ASLogic
(Accepts user-defined text), 0.735, 0.750, 0.765 Identifies the CAS reference
voltage for MSOx Logic
Triggering.
Confgure VRef CKE
Signal(V)
InputRef
V_VrefCK
ELogic
(Accepts user-defined text), NA, 0.735, 0.750, 0.765 Identifies the CKE reference
voltage for MSOx Logic
Triggering.
Confgure VRef CS
Signal(V)
InputRef
V_VrefCS
Logic
(Accepts user-defined text), 0.735, 0.750, 0.765 Identifies the CS reference
voltage for MSOx Logic
Triggering.
Confgure VRef
RAS
Signal(V)
InputRef
V_VrefR
ASLogic
(Accepts user-defined text), 0.735, 0.750, 0.765 Identifies the RAS reference
voltage for MSOx Logic
Triggering.
Confgure VRef WE
Signal(V)
InputRef
V_VrefW
ELogic
(Accepts user-defined text), 0.735, 0.750, 0.765 Identifies the WE reference
voltage for MSOx Logic
Triggering.
Confgure VRefCA
(V)
InputRef
V_VrefC
A
(Accepts user-defined text), 0.950, 0.800, 0.650 Identifies the input reference
voltage for Address and
Command inputs.
Confgure VRefDQ
(V)
InputRef
V_VrefD
Q
(Accepts user-defined text), 0.950, 0.800, 0.650 Identifies the input reference
voltage for DQ and DM
inputs.
Confgure VTT (V) InputRef
V_VTT
(Accepts user-defined text), 0.950, 0.800, 0.650 Identifies the output
reference voltage for data
outputs.
Confgure Vcent
Evaluatio
n Mode
VcentEva
lMode
0, 1 Select the method of Vcent
level evaluation for shifting of
the tDIVW/vDIVW mask.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 49

Confgure WE
Channel
WEDigCh
annel
DIGital0, DIGital1, DIGital2, DIGital3, DIGital4,
DIGital5, DIGital6, DIGital7, DIGital8, DIGital9,
DIGital10, DIGital11, DIGital12, DIGital13, DIGital14,
DIGital15
Identifies the channel source
selection of the WE digital
signal to be analyzed for
MSOx Logic Triggering.
Confgure WRITE
Latency
WriteLat
ency
1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0,
13.0, 14.0, 15.0, 16.0, 17.0, 18.0, 19.0, 20.0
This value is used ONLY
when the "Rank Separation"
option is enabled. This allow
user to specify the overall
Write latency(WL) value to
be used in performing the
Data Strobe Timing and Data
Timing tests when the "Rank
Separation" option is
enabled. By definition, the
Write Latency (WL) =
Additive Latency (AL) + CAS
Write Latency (CWL); WL =
AL + CWL.
Confgure WRITE
Latency
Value
WLValue 1.0, 2.0, 3.0, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0, 10.0, 11.0, 12.0,
13.0, 14.0, 15.0, 16.0, 17.0, 18.0, 19.0, 20.0
This value is used ONLY
when the "Rank Separation"
option is enabled. This allow
user to specify the overall
Write latency(WL) value to
be used in generating the
WRITE eye diagram when the
"Rank Separation" option is
enabled. By definition, the
Write Latency (WL) =
Additive Latency (AL) + CAS
Write Latency (CWL); WL =
AL + CWL.
Confgure Wavefor
m File
Type
WfmFile
Type
.wfm, .h5 By selecting ".wfm", the
application will save the
waveform in wfm format for
measurement. While
selecting ".h5", the
application will save the
waveform in h5 format for
measurement.
Confgure Wavefor
m Source
Source 1, 2, 3, 4 Identifies the source Channel
of the data to be analyzed.
Confgure tDQSCK
Delay
(cycle)
tDQSCKD
elay
(Accepts user-defined text), 1, 2, 3, 4, 5, 6 The distance from first rising
strobe to Read Latency(RL)
clock edge.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
50 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

Confgure terr(nper)
Maximu
m N
Width
Value
nper_ma
x
(Accepts user-defined text), 50 Sets the upper bound
(inclusive) of the inner sliding
window for the terr(nper)
series.
Confgure terr(nper)
Minimu
m N
Width
Value
nper_min (Accepts user-defined text), 13 Sets the lower bound
(inclusive) of the inner sliding
window for the terr(nper)
series.
Run
Tests
Event RunEven
t
(None), Fail, Margin < N, Pass Names of events that can be
used with the
StoreMode=Event or
RunUntil RunEventAction
options
Run
Tests
RunEven
t=Margin
< N:
Minimu
m
required
margin %
RunEven
t_Margin
<
N_MinPe
rcent
Any integer in range: 0 <= value <= 100 Specify N using the
'Minimum required margin
%' control.
Set Up Burst
Triggerin
g Method
BurstTrig
Method
DQS-DQ Phase Difference, MSOx Logic Triggering This option allow user to
select burst triggering
method.
Set Up Custom
Data
Rate
pcboCust
omSG
(Accepts user-defined text), 1600, 1866, 2133, 2400,
2666, 3200
This option allow user to key
in specific data rate.
Set Up Device ID pcboOver
allDevice
ID
(Accepts user-defined text) This option allow user to key
in related test details.
Set Up Speed
Grade
DeviceTy
pe
DDR4-1600, DDR4-1866, DDR4-2133, DDR4-2400,
DDR4-2666, DDR4-3200
This option allow user to
select specific speed grade.
Set Up Test
Mode
AcLevels
_CA
120 This option allow user to
select test mode.
Set Up Test
Mode
AcLevels
_DQ
120 This option allow user to
select test mode.
Set Up Test
Mode
TestMod
e
Compliance, Custom This option allow user to
select test mode.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
Configuration Variables and Values 2
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 51

Set Up User
Commen
t
txtOveral
lUserCo
mment
(Accepts user-defined text) This option allow user to key
in related test detail.
Set Up User
Descripti
on
pcboOver
allDevice
Descripti
on
(Accepts user-defined text) This option allow user to key
in test detail.
Table 2 Configuration Variables and Values (continued)
GUI
Location
Label Variable Values Description
52 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
2 Configuration Variables and Values

s1
53

Agilent N6462A DDR4 Compliance Test Application
Programmer's Reference
3
Test Names and IDs
The following table shows the mapping between each test's numeric ID and
name. The numeric ID is required by various remote interface methods.
Name The name of the test as it appears on the user interface Select
Tests tab.
Test ID The number to use with the RunTests method.
Description The description of the test as it appears on the user
interface Select Tests tab.
For example, if the graphical user interface displays this tree in the Select
Tests tab:
All Tests
Rise Time
Fall Time
then you would expect to see something like this in the table below:
and you would run these tests remotely using:
ARSL syntax
-----------
arsl -a ipaddress -c "SelectedTests '100,110'"
arsl -a ipaddress -c "Run"
C# syntax
---------
remoteAte.SelectedTests = new int[]{100,110};
remoteAte.Run();
Here are the actual Test names and IDs used by this application:
Table 3 Example Test Names and IDs
Name Test ID Description
Fall Time 110 Measures clock fall time.
Rise Time 100 Measures clock rise time.
54 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
3 Test Names and IDs

NOTE
The file, ""TestInfo.txt"", which may be found in the same directory as this help file,
contains all of the information found in the table below in a format suitable for parsing.
Table 4 Test IDs and Names
Name TestID Description
DummyTestToShowDQSDQPh
aseConfig1
3 DummyTestToShowDQSDQPhaseConfig1
DummyTestToShowLogicTrigC
onfig
5 DummyTestToShowLogicTrigConfig
Eye Diagram Test For Read
Cycle
20401 User Defined Real-Time Eye Diagram Test For Read
Cycle
Eye Diagram Test For Read
Cycle
20405 User Defined Real-Time Eye Diagram Test For Read
Cycle (MSOX version)
Eye Diagram Test For Write
Cycle
20402 User Defined Real-Time Eye Diagram Test For Write
Cycle
Eye Diagram Test For Write
Cycle
20406 User Defined Real-Time Eye Diagram Test For Write
Cycle (MSOX version)
Overshoot amplitude
(Address, Control)
10351 Peak amplitude of AC overshoot
Overshoot amplitude
(Address, Control, Clock, Chip
Select, Clock Enable)
10355 Peak amplitude of AC overshoot
Overshoot amplitude (Clock) 10359 Peak amplitude of AC overshoot
Overshoot amplitude (Data,
Strobe, Mask)
10353 Peak amplitude of AC overshoot
Overshoot amplitude (Data,
Strobe, Mask)
10357 Peak amplitude of AC overshoot
Overshoot area (Address,
Control)
10352 OverShoot area above VDD
Overshoot area (Address,
Control, Clock, Chip Select,
Clock Enable)
10356 OverShoot area above VDDCA
Overshoot area (Clock) 10360 OverShoot area above VDDQ
Overshoot area (Data, Strobe,
Mask)
10354 OverShoot area above VDDQ
Overshoot area (Data, Strobe,
Mask)
10358 OverShoot area above VDDQ
SLEWf 10342 Input signal minimum falling slew rate
Test Names and IDs 3
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 55

SLEWr 10341 Input signal minimum rising slew rate
SRQdiffF 11414 Differential Output Falling Slew Rate
SRQdiffR 11413 Differential Output Rising Slew Rate
SRQseF 11342 Output signal minimum falling slew rate
SRQseR 11341 Output signal minimum rising slew rate
Undershoot amplitude
(Address, Control)
10361 Peak amplitude of AC undershoot
Undershoot amplitude
(Address, Control, Clock, Chip
Select, Clock Enable)
10365 Peak amplitude of AC undershoot
Undershoot amplitude (Clock) 10369 Peak amplitude of AC undershoot
Undershoot amplitude (Data,
Strobe, Mask)
10363 Peak amplitude of AC undershoot
Undershoot amplitude (Data,
Strobe, Mask)
10367 Peak amplitude of AC undershoot
Undershoot area (Address,
Control)
10362 UnderShoot area below VSS
Undershoot area (Address,
Control, Clock, Chip Select,
Clock Enable)
10366 UnderShoot area below VSS
Undershoot area (Clock) 10370 UnderShoot area below VSSQ
Undershoot area (Data,
Strobe, Mask)
10368 UnderShoot area below VSS
Undershoot area (Data,
Strobe, Mask)
10364 UnderShoot area below VSSQ
VIH.CA(AC) 10311 AC Input Logic High
VIH.CA(DC) 10312 DC Input Logic High
VIH.DQ(AC) 10313 AC Input Logic High
VIH.DQ(DC) 10314 DC Input Logic High
VIHdiff.CK(AC) 10411 Differential AC Input Logic High Voltage
VIHdiff.CK(DC) 10415 Differential DC Input Logic High Voltage
VIHdiff.DQS(AC) 10413 Differential AC Input Logic High Voltage
VIHdiff.DQS(DC) 10417 Differential DC Input Logic High Voltage
VIL.CA(AC) 10321 AC Input Logic Low
Table 4 Test IDs and Names (continued)
Name TestID Description
56 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
3 Test Names and IDs

VIL.CA(DC) 10322 DC Input Logic Low
VIL.DQ(AC) 10323 AC Input Logic Low
VIL.DQ(DC) 10324 DC Input Logic Low
VILdiff.CK(AC) 10412 Differential AC Input Logic Low Voltage
VILdiff.CK(DC) 10416 Differential DC Input Logic Low Voltage
VILdiff.DQS(AC) 10414 Differential AC Input Logic Low Voltage
VILdiff.DQS(DC) 10418 Differential DC Input Logic Low Voltage
VIX 10380 AC differential input cross point voltage
VIX(CK) 10381 Clock Cross Point Voltage Test
VIX(DQS) 10382 Strobe Cross Point Voltage Test
VOH(AC) 11311 AC Output Logic High
VOH(DC) 11312 DC Output Logic High
VOHdiff(AC) 11411 Differential AC Output Logic High Voltage
VOL(AC) 11321 AC Output Logic Low
VOL(DC) 11322 DC Output Logic Low
VOLdiff(AC) 11412 Differential AC Output Logic Low Voltage
VSEH(Clock) 10333 Single-ended High Level Voltage
VSEH(Strobe) 10331 Single-ended High Level Voltage for Strobes
VSEL(Clock) 10334 Single-ended Low Level Voltage
VSEL(Strobe) 10332 Single-ended Low Level Voltage for Strobes
tCH Average High
Measurements
2000 tCH Average High Measurements
tCK(abs) Period Rising Edge
Measurements
1 tCK Period Rising Edge Measurements
tCK(abs) Rising Edge
Measurements
2 tCK(abs) Rising Edge Measurements
tCK(avg) Rising Edge
Measurements
200 tCK(avg) Rising Edge Measurements
tCKE 30206 CKE Minimum Pulse Width
tCL Average Low
Measurements
2050 tCL Average LowMeasurements
tDH(base) 30302 DQ and DM input hold time - Differential
Table 4 Test IDs and Names (continued)
Name TestID Description
Test Names and IDs 3
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 57

tDH-Diff(derate) 30304 DQ and DM input hold time - Differential
tDIPW 30305 DQ and DM input pulse width
tDIVW Margin 20403 tDIVW Margin
tDQSCK 30021 DQS output access time from CK,/CK
tDQSH 30107 DQS input high pulse width
tDQSL 30108 DQS input low pulse width
tDQSQ 30104 DQS-DQ skew for DQS and associated DQ signals
tDQSS 30106 DQS latching transition to associated clock edge
tDS(base) 30301 DQ and DM input setup time - Differential
tDS-Diff(derate) 30303 DQ and DM input setup time - Differential
tDSH 30110 DQS falling edge hold time from CK
tDSS 30109 DQS falling edge to CK setup time
tDVAC(Clock) 30022 tDVAC(Clock)
tDVAC(Strobe) 30117 tDVAC(Strobe)
tHZDQ 30101 DQ out high-impedance time from CK,/CK
tHZDQS 30118 DQS high-impedance time from CK,/CK
tIH(base) 30202 Address and control input hold time
tIH(derate) 30204 Address and control input hold time
tIS(base) 30201 Address and control input setup time
tIS(derate) 30203 Address and control input setup time
tLZDQ 30102 DQ low-impedance time from CK,/CK
tLZDQS 30103 DQS low-impedance time from CK,/CK
tQH 30105 DQ/DQS output hold time from DQS
tQSH 30115 DQS output high time
tQSL 30116 DQS output low time
tRPRE 30113 Read preamble
tRPST 30114 Read postamble
tVAC(CS,CA) 30205 tVAC(CS,CA)
tVAC(Data) 30306 tVAC(Data)
tWPRE 30111 Write preamble
tWPST 30112 Write postamble
Table 4 Test IDs and Names (continued)
Name TestID Description
58 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
3 Test Names and IDs

terr(10per) Rising Edge
Measurements
1200 terr(10per) Rising Edge Measurements
terr(11per) Rising Edge
Measurements
1300 terr(11per) Rising Edge Measurements
terr(12per) Rising Edge
Measurements
1400 terr(12per) Rising Edge Measurements
terr(2per) Rising Edge
Measurements
400 terr(2per) Rising Edge Measurements
terr(3per) Rising Edge
Measurements
500 terr(3per) Rising Edge Measurements
terr(4per) Rising Edge
Measurements
600 terr(4per) Rising Edge Measurements
terr(5per) Rising Edge
Measurements
700 terr(5per) Rising Edge Measurements
terr(6per) Rising Edge
Measurements
800 terr(6per) Rising Edge Measurements
terr(7per) Rising Edge
Measurements
900 terr(7per) Rising Edge Measurements
terr(8per) Rising Edge
Measurements
1000 terr(8per) Rising Edge Measurements
terr(9per) Rising Edge
Measurements
1100 terr(9per) Rising Edge Measurements
terr(nper) Rising Edge
Measurements
3000 terr(nper) Rising Edge Measurements
tjit(CC) Rising Edge
Measurements
100 tjit(CC) Rising Edge Measurements for 800MT/s
tjit(duty-high) Jitter Average
High Measurements
2100 tjit(duty-high) Jitter Average High Measurements
tjit(duty-low) Jitter Average
Low Measurements
2150 tjitduty-low Jitter Average LowMeasurements
tjit(per) Rising Edge
Measurements
300 tjit(per) Rising Edge Measurements
vDIVW Margin 20404 vDIVW Margin
Table 4 Test IDs and Names (continued)
Name TestID Description
s1
59

Agilent N6462A DDR4 Compliance Test Application
Programmer's Reference
4
Instruments
The following table shows the instruments used by this application. The
name is required by various remote interface methods.
Instrument Name The name to use as a parameter in remote
interface commands.
Description The description of the instrument.
For example, if an application uses an oscilloscope and a pulse generator,
then you would expect to see something like this in the table below:
and you would be able to remotely control an instrument using:
ARSL syntax (replace [description] with actual parameter)
----------------------------------------------------------------------
arsl -a ipaddress -c "SendScpiCommandCustom 'Command=[scpi
command];Timeout=100;Instrument=pulsegen'"
arsl -a ipaddress -c "SendScpiQueryCustom 'Command=[scpi
query];Timeout=100;Instrument=pulsegen'"
C# syntax (replace [description] with actual parameter)
----------------------------------------------------------------------
SendScpiCommandOptions commandOptions = new SendScpiCommandOptions();
commandOptions.Command = "[scpi command]";
commandOptions.Instrument = "[instrument name]";
commandOptions.Timeout = [timeout];
remoteAte.SendScpiCommand(commandOptions);
SendScpiQueryOptions queryOptions = new SendScpiQueryOptions();
queryOptions.Query = "[scpi query]";
queryOptions.Instrument = "[instrument name]";
queryOptions.Timeout = [timeout];
remoteAte.SendScpiQuery(queryOptions);
Table 5 Example Instrument Information
Name Description
scope The primary oscilloscope.
Pulse The pulse generator used for Gen 2 tests.
60 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
4 Instruments

Here are the actual instrument names used by this application:
NOTE
The file, ""InstrumentInfo.txt"", which may be found in the same directory as this help file,
contains all of the information found in the table below in a format suitable for parsing.
Table 6 Instrument Names
Instrument Name Description
scope The primary oscilloscope
Agilent N6462A DDR4 Compliance Test Application Programmer's Reference 61

Index
C
configuration variables and values, 11
I
IDs and names of tests, 53
instrument names, 59
L
licensing, 9
N
names and IDs of tests, 53
names of instruments, 59
notices, 3
P
programming, introduction to, 7
R
Remote Programming Toolkit, 8
T
test names and IDs, 53
V
variables and values, configuration, 11
62 Agilent N6462A DDR4 Compliance Test Application Programmer's Reference
Index