Scribd
Upload
670 views6 pages

Electric Fan Project

The document provides instructions for building an electric fan project using a 3D printer. It describes the necessary components, which include a 3D printed fan base and blade files, a motor, and battery box. It outlines two methods for 3D printing the fan parts from either pre-made GCODE files or STL files using modeling software. Basic safety tips are provided and it discusses how the motor can generate electricity if used in a generator or turbine setup.

Uploaded by

Gaurav Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
670 views6 pages

Electric Fan Project

The document provides instructions for building an electric fan project using a 3D printer. It describes the necessary components, which include a 3D printed fan base and blade files, a motor, and battery box. It outlines two methods for 3D printing the fan parts from either pre-made GCODE files or STL files using modeling software. Basic safety tips are provided and it discusses how the motor can generate electricity if used in a generator or turbine setup.

Uploaded by

Gaurav Singh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

ELECTRIC FAN PROJECT

ENERGY Challenge Project


Using the RapMan 3D Printer

Along With the RapMan you will Need
1 - 3V. DC Motor
1 - Battery Box with Switch
STL File for the Fan Blade
STL File for the Fan Base



THERE ARE TWO WAYS YOU CAN PRODUCE THE FAN PROJECT
FIND THE DISK LABLED Electric Fan Project THAT CAME WITH THE MOTORS AND BATTERY BOXES
USE THE GCODE FILES NAMED:
FANBASE.BFB (This Prints the Base that Holds the Motor)
FANBLADE.BFB ( This Prints the Fan Blade)
JUST COPY THESE TWO FILES TO THE SD CARD
SIMPLY FOLLOW THE RAPMAN OPERATION MANUAL FOR PRINTING


OR
USE THE STL FILES NAMED:
FANBASE (This is the 3D Model of the Fan Base)
FANBLADE (This is the 3D Model of the Fan Blade)
COPY THE THESE TWO FILES TO A FOLDER (a desktop folder labeled STL FILES works great)
SIMPLY FOLLOW THE BFB AXON SOFTWARE MANUAL ALONG WITH THE SOFTWARE
TO PRODUCE THE GCODE











A completed Electric Fan Using Components that We now Supply with the Kit: 10 Each Motor and Battery Box
Could We Replace the Battery With A Solar Cell?
YOU MUST WEAR SAFETY GLASSES AT ALL TIMES WITH THIS PROJECT

After you remove the Blade from the Raft use a Knife to
Gently clear the ABS to reveal the Hole
This Side is where the Motor Shaft will press in








Using a Drill Press to PRESS the Motor SHAFT into the Fan Blade, You could use a Vise as well: NEVER PRESS ON THE MOTOR HOUSING



A 3Volt DC MOTOR HAS PERMANENT MAGNETS, If you Rotate the Shaft The
Motor Will Produce DC Current ( voltage )
SO IF YOU WERE TO DIRECT AIR TO THE SIDE OF THE FAN BLADE
THE MOTOR WOULD SPIN AND BECOME A GENERATOR
THE SAME WOULD APPLY IF YOU WERE TO USE WATER

STEAM (air under pressure) GENERATED ELECTRICITY ( Coal or Nuclear )
WIND GENERATED ELECTRICITY ( Wind Farms )
HYDRO (water) GENERATED ELECTRICITY ( Man Made Dams )
Although on A Smaller Scale You Will Encounter The Same Efficacy Problems As Scientists Around the World




YOU MUST WEAR SAFETY GLASSES AT ALL TIMES WITH THIS PROJECT
The Above Project Was Built With 1/4" Copper Tubing And 1/4" Plastic Tubing. The ABS Is Very Easy to Drill. Drill under size to press fit. We Used An Air
Compressor To Power The Turbine. You Could Use Water As Well But Design Some Type Of Splash Shield. Attach a Volt Meter To the Motor. You Should
Read About 2.8 Volts DC Output. Think About What you Would Need to Store The Energy this Will Produce.






Removing the Raft
Place your Hand on and Under the Edge of the Print Board
Using the Putty knife , Slide it under the Raft Rocking Left and Right Pushing Parallel with the Print Bed
DO NOT PUSH DOWN

You might also like