Enthalpy Changes

During a chemical reaction or physical change heat energy is either transferred

into the
surroundings from the chemicals or absorbed from the surrounding.
The amount of heat energy (Q) transferred depends on three factors:
1. The capacity of the substance to absorb heat called the specific heat
capacity (c).
2. The amount (moles) of the substances reacting
3. The change in temperature
The amount of heat transferred is proportional to each of these three factors. T
o moles and Q o
moles. So if the number of moles increases the temperature increases and the
amount of heat
energy transferred will be greater.
This simulation shows the effect of the mass of ammonium nitrate on the
temperature
change when it is dissolved in water.
To calculate the energy / enthalpy / heat energy / heat absorbed or released the
following formula is used:
Where:
Mass of the substance (m)
The substance experiencing the temperature change. It is measured in grams (g).
In an aqueous solution, m represents the total mass of aqueous solution. We
make the
assumption that 100 ml of solution = 100 g.
In reactions involving a solid reactant which is often in excess, we assume m
is the mass of
the aqueous reactant. 100 ml of solution = 100 g
For combustion reactions, m refers to the mass of water that the heat energy is
transferred
into. 100 ml water = 100 g water.
For metals, m represents the mass of the metal.
Specific heat capacity (c)
Each substance absorbs heat to different extents. The specific heat is defined as
the amount of
heat (per unit mass of the substance) energy required to raise 1 gram of the
substance by 1C.
It is measured in J g-1K-1 (= kJ kg-1K-1) The larger the specific heat capacity the
more heat energy
1 g of the substance needs to absorb to cause a 1C temperature rise.
Water has a high heat capacity (4.18 J g-1 K-1 / kJ kg-1K-1) compared to other
substances like air (1.00
2 | P a g e
J g-1 K-1). This is an important physical property of water and means that water
can absorb (and
release) large amounts of heat energy with relatively small temperature changes.
In the summer for
example the air temperature can be 35oC but the water in a swimming pool is only
23oC. This is
because when the water absorbs heat energy from the sun, its higher heat
capacity means it will
change the temperature of the water less than the air.
In most calculations involving aqueous solutions we make the assumption that the
specific heat
capacity of the solution is equal to the specific heat capacity of water.
Remember an assumption is
something you assume to be true but you are not sure. A lot of assumptions are
made in science
because they simplify models.
Energy / enthalpy / heat energy (q/Q)
Measured in Joules (J) or kilojoules (kJ). If the reaction is exothermic Q is
given a negative sign and
if endothermic a positive sign. Express in KJ unless J is specifically asked for.
Temperature
Measured in Kelvin (K). 0C = 273 K. The change in temperature, AT has the same
numerical value
on both the Celsius and Kelvin scales, so no conversion is needed.
Unit Conversions
The units given for c must be the same as those used for Q, m and AT. E.g. if c =
4.18 J g-1 K-1
then q must be in Joules, m in grams and AT in K. Make conversions where
necessary. The specific
heat capacity of water is found on page 2 of the Chemistry data booklet.
g | 1000 = kg kg x 1000 = g
J | 1000 = kJ kJ x 1000 = J
0C +273 = 273 K (Kelvin) 273 K - 273 = 0C
Worked example:
If you drink a cold glass of water (250 g) at 0.0 C, how much heat is transferred
to the water as it
warms to 37.0 C. The specific heat capacity of water is 4.18 Jg-1K-1.
Answer:
m = 250 g of water (3SF, measured value }1g)
C = 4.18 Jg-1K-1
AT = 37.0 0.0 = 37.0 C (37.0 K)
Q = m C AT
= (250 g) (4.18 Jg-1K-1) (37.0K)
= 3.87 x 104 J
= 38.7 kJ (3SF)
3 | P a g e
Enthalpy change, AH
The enthalpy change is a measure of the difference in the heat energy of the
products and
reactants. It is measured in kJmol-1 (unless Jmol-1 is specifically asked for).
enthalpy change , AH = m x c x AT
n ( limiting reagent)
or
AH = Q
n
Where n is the actual number of moles of the limiting reagent in
the chemical reaction:
n = m or c = n
M v
Remember to determine the limiting reagent
1. Find the actual number of moles of each reactant.
2. Find the number of moles needed (required) of each reactant from the moles
ratio in the
equation.
3. If the moles of reactant you have < moles needed then this is the limiting
reactant
Problems
1. When 1.00g of sodium hydroxide is dissolved in 100.0 g of water in an
insulated container
the temperature rises from 20.00C to 22.66C. Calculate the enthalpy change for
the
solution. State any assumptions made. NOTE: Dissolving reactions due not have
limiting
reagents.
4 | P a g e
2. When 100.0 ml of 1.00 moldm-3 NaOH is added to 100.0 ml of 1.00 moldm-3 HCl in
an
insulated container the temperature rises from 21.0C to 34.6C.
NaOH(aq) + HCl (aq) NaCl(aq) + H2O(l)
Calculate the enthalpy change for the neutralization reaction. State any
assumptions made.
The enthalpy change can also be determined using the mole ratios in the equation.
For example in
the following reaction:
2 Mg + O2 2 MgO AH = - 1202 kJ mol-1
The reaction says:
2 moles Mg reacts with 1 mole O2 to produce 2 mole of MgO 1202 kJ mol-1 of energy
is released or
AH = 1202 kJ mol-1
Using mole ratios:
1 mole Mg reacts with . mole O2 to produce 1mole of MgO 1202 2 = 601 kJ mol-1 of
energy is
released or AH = 601 kJ mol-1
2 Mg + O2 2 MgO AH = - 1202 kJ mol-1
mole ratios: 2 1 2 AH = -1202 kJ mol-1
or 1 . 1 AH = -1202 2 = 601 kJ mol-1
Standard conditions
The change in enthalpy, AH varies according to the conditions of the experiment
and is affected by
temperature, pressure and concentration. All literature values for enthalpy
changes are
determined under standard conditions.
5 | P a g e
Standard conditions are:
1 atm or 1.01 x 105 Pa or 101 kPa
1 mole of gas
Temperature of 298K or 25C.
Measuring heat transfer (enthalpy changes)
Many enthalpy changes can be measured simply in the laboratory. If we measure the
temperature
change of the water and we know its mass and specific heat capacity we can work
out how much
energy was transferred to or from the water during the chemical reaction. We can
find the change
in enthalpy if we know the mass of the reactant/s. A calorimeter can be used to
get more accurate
values for enthalpy changes. A calorimeter container usually is well-insulated
with styrofoam
(polystyrene) and has a lid to minimizes heat loss. If it is not insulated
properly the reaction can
either gain or lose heat energy to the surroundings.
A calorimeter
Procedure for finding enthalpy change of a reaction in an aqueous solutions
1. Take one reactant of known volume and concentration. This will be the limiting
reagent.
2. Place in the calorimeter or some other insulated container like a styrofoam
cup.
3. Record the initial temperature in C.
4. Take an excess (or equal) mole of the other reactant of known volume and
concentration.
Record its initial temperature in C.
5. Quickly add the excess reactant to the calorimeter, cover and stir rapidly to
minimize heat
loss.
6. Record the temperature change over time.
7. Determine the maximum temperature in C.
8. Calculate enthalpy change, H using the number of moles of limiting reagent
and the
equation H = (m x c x T) nlimiting reagent
Procedure for finding the enthalpy change of a solid or liquid fuel
1. Take a calorimeter containing a known volume of water.
2. Record the temperature of the water.
3. Take a known mass of fuel.
6 | P a g e
4. Burn the fuel under the calorimeter minimizing heat loss to the surroundings.
The energy
released will be used to heat the water. The water in the calorimeter must be
stirred to
make sure that the heat is distributed evenly.
5. At the end of the reaction record the change in mass of the fuel and the
change in
temperature.
6. Calculate enthalpy change, H using the number of moles of fuel and the
equation H = (m
x c x T) nlimiting reagent
Sources of systematic error and how they can be minimized
Systematic errors will cause the experimental enthalpy change, H to be less
than the accepted
value.
1. The reaction is not stirred or stirred too slowly. This will increase the time
taken for the
reaction and will increase the amount of heat lost. Minimize by stirring rapidly
when the
second reactant is added and extrapolate the graph of temp vs. time to determine
the
temperature change for an instantaneous reaction.
2. The reaction container is not insulated adequately resulting the reaction can
either gain or
lose heat energy to the surroundings. This will make the change in temperature
less then
accepted and decrease the enthalpy change. Minimize be ensuring the reaction
container is
insulated correctly with styrofoam, and has an insulating lid. Alternatively a
temperature
versus time graph can be plotted and the instantaneous change in temperature
determined
from extrapolation.
3. The transfer of heat to the temperature probe and metal reactants is ignored.
4. The reaction is not carried out under standard conditions of 1 atm (1.01 x 105
Pa),
concentration of 1 mol l-1 and a temperature of 298K or 25C. All literature
values are
determined under standard conditions.
5. Assumption that the specific heat capacity of the solutions is equal to that
of water.
A bomb calorimeter is used for making more
accurate measurements that are closer to the
accepted value in combustion reactions (not
for aqueous solutions). The fuel to be burned
is electrically ignited and burns in oxygen.
Energy is transferred to the surroundings,
water, whose temperature rise is measured.
7 | P a g e
Experiments involving the calculation of enthalpy changes
8 | P a g e
Questions
To receive full credit, the method used and the steps involved at arriving at you
final answer must
be shown clearly. For numerical calculations please pay proper attention to
significant figures.
1. Aluminum has a specific heat of 0.902 Jg-1K-1. How much heat is lost when a
piece of
aluminum with a mass of 23.984 g cools from a temperature of 415.0 oC to a
temperature of
22.0 oC?
2. The temperature of a sample of water increases by 69.5 oC when 24 500 J are
applied. The
specific heat of liquid water is 4.18 Jg-1K-1. What is the mass of the sample of
water?
3. 850 joules of heat are applied to a 250 g sample of liquid water with an
initial temperature
of 13.0 oC. Find a) the change in temperature and b) the final temperature.
4. When 34 700 J of heat are applied to a 350 g sample of an unknown material the
temperature rises from 22.0 oC to 173.0 oC. Calculate the specific heat of this
material?
5. Calculate how much energy in kJ is needed to warm 250.0 ml water from 25.0 C
to 95.0 C
in order to make a cup of coffee? (250 ml = 250 g)
6. Determine the specific heat capacity of methanol if 1.80 x102J of heat is
added to 70 g of
liquid methanol and its temperature increases from 18.5oC to 30.5oC.
7. (N00/S) When 50.0 cm3 of 1 moldm-3 HCl is mixed rapidly with 50.0 cm3 of 1 moldm-
3 NaOH,
the temperature of the resulting solution increases by 6oC. Determine the
temperature
change when:
a) 100 cm3 of each of these solutions is mixed
b) 2 mol dm-3 of each solution is mixed
8. When 8.00 g of ammonium nitrate (NH4NO3) was dissolved in 100.0 ml water, the
temperature fell from 19.0 C to 14.5 C.
a) Calculate the enthalpy (Q) of the solution in J and kJ.
b) The experiment was repeated but with 10.0 g of NH4NO3. State and explain if
there
would be a change in temperature.
9. An experiment was carried out to determine the amount of energy released in a
low fat chocolate bar with a mass of 50.0 g. The complete combustion of a
10.0 g sample
of the bar raised the temperature of 500.0g of water from 19.0 C to 86.5C.
Calculate the
energy value (kJ) of the chocolate bar.
10. 500.0g of water were heated on a gas camping stove from 20.0 C to 100.0C.
If the pot was
made of aluminum (specific heat capacity 875 kJ kg-1 K-1) and it weighed 100.0 g,
calculate
the heat energy (q) required in kJ to heat:
a) The pot
b) The water
c) The gas camping stove contained butane (C4H10). 14.5g of butane was used to
boil
the water. How many moles of butane was this?
9 | P a g e
11. Calculate the change in the enthalpy, AH of combustion of ethanol in Jmol-1
when 0.920g of
ethanol was burned under a calorimeter containing 400.0 ml of water. The
temperature
rose by 10.0 C
CH3CH2OH(l) + 3 O2(g) 2 CO2 (g) + 3 H2O(g)
12. For the reaction: N2(g) + 3H2(g) 2NH3(g) AH = - 92.0 kJ mol-1
a) Determine the heat energy released when 2 moles of nitrogen reacts.
b) Determine the energy released when 0.50 mole of ammonia is formed.
c) Calculate the number of moles of nitrogen that react to produce 1840 kJ mol-1
of
energy?
d) Determine the heat energy released when 10.0 g of hydrogen burns.
13. In cooking Crepe Suzette, a delicious type of French pancake one
tablespoon (2.50g) of
brandy (containing ethanol) is poured over the pancakes and then it is ignited.
a) The molar mass of the ethanol is 46.08 gmol-1. Calculate the number of moles of
ethanol, C2H5OH in the tablespoon?
b) The enthalpy change for the reaction is 1350 kJmol-1. Calculate the heat
released
when the brandy on the Crepe Suzette burns?
14. (N01/H/2) 10.0 g of NaOH is added to 100.0 g of water at 23.2C in a glass
beaker. The
solution is stirred and the maximum temperature of 44.6C is reached.
a) Calculate the heat produced by the reaction. (Assume the specific heat
capacity of the
solution is 4.20 Jg-1C-1). Is the reaction exothermic or endothermic [4]
b) Calculate the enthalpy change for dissolving the solid NaOH in water in kJmol-
1. [2]
c) Write an equation for the dissolving process. [1]
d) The value given in the literature under similar conditions is -42.7 kJmol-1.
Suggest a reason
why the calculated value of the enthalpy change of the solution is different from
the
literature value and propose an improvement in the procedure to obtain a more
accurate
result. [2]
15. (M00/H/2) Describe an experiment that could be conducted in the school
laboratory to
determine the value of H (in kJmol-1) for the neutralization reaction between
HCl and
NaOH. Write an equation for the reaction and show the calculation that would need
to be
carried out to obtain the value for H. [7]
16. (M05/S/2) In a neutralization reaction 50.0 cm3 of a 0.500 moldm-3 solution of
potassium
hydroxide is mixed rapidly in a glass beaker with 50.0 cm3 of a 0.500 moldm-3
solution of
hydrochloric acid.
Initial temperature of each solution = 19.6C
Final temperature of the mixture = 23.1C
a) Write an equation for the reaction. [1]
b) State with a reason whether the reaction was exothermic or endothermic. [1]
10 | P a g e
c) Explain why the solutions were mixed rapidly. [1]
d) Calculate the enthalpy change in kJmol-1. Assume that the specific heat
capacity of the
solution is the same as that of water. [1]
e) If the experiment was repeated with an HCl concentration of 1 moldm-3 state and
explain
what the temperature change would be.
17. (N98/H/2) The reaction between a strong base, sodium hydroxide and a strong
acid, sulfuric
acid was studied by measuring the heat produced during neutralization. Volumes of
1.25
moldm-3 of the base ranging from 10.0 to 50.0 cm3 were mixed with the required
volumes of
1.25 moldm-3 solution of the acid to produce a total volume of 60.0 cm3. The
changes in
temperature were measured and recorded in the table below.
Volume base (cm3) Temperature (C)
10.0 2.2
20.0 4.6
30.0 7.0
40.0 7.0
50.0 3.5
a) Write an equation to represent the neutralization reaction. [1]
b) Draw a graph of the results. [5]
c) From the graph determine the greatest temperature increase. [2]
d) Calculate the number of moles of base and the number of moles of acid in (c).
[4]
e) Determine the limiting reagent. [1]
f) Calculate the energy released, Q in joules by the reaction when the maximum
temperature was obtained on the graph. [2]
g) Calculate the enthalpy of neutralization, H [2]
h) The accepted value for the enthalpy of neutralization is -55.5 kJmol-1. Outline
two
sources of error in the experimental procedure that could result in a calculated
value of
H that is smaller than the accepted value and suggest a way that one of these
could be
minimized. [3]
Bibliography
Clark, Jim. Chem Guide. 2008. <http://www.chemguide.co.uk/>.
Clugston, Michael and Rosalind Flemming. Advanced Chemistry. Oxford: Oxford University
Press, 2000.
Derry, Lanna, Maria Connor and Carol Jordan. Chemistry for use for the IB Diploma
Standard level.
Melbourne: Pearson Education, 2008.
Green, John and Sadru Damji. Chemistry for use with the International Baccalaureate
Programme.
Melbourne: IBID Press, 2007.
11 | P a g e
Neuss, Geoffrey. IB Diploma Programme Chemistry Course Companion. Oxford: Oxford
University Press,
2007.
. IB Study Guides, Chemistry for the IB Diploma. Oxford: Oxford University Press, 2007.
Organisation, International Baccalaureate. Online Curriculum Centre.
<http://occ.ibo.org/ibis/occ/guest/home.cfm>.
. "Chemistry Data Booklet." International Baccalaureate Organisation, March 2007.
. "Chemistry Guide." International Baccalaureate Organisation, March 2007.
. "IB Chemistry Examination Papers ." Cardiff: International Baccalaureate Organisation,
1999-2008.
Organisation, International Bacclaureate. "Theory of Knowledge Subject Guide."
International Baccalaureate
Organisation, March 2006.
Problems Answers
1. When 1.00g of sodium hydroxide is dissolved in 100.0 g of water in an insulated
container
the temperature rises from 20.00C to 22.66C. Calculate the enthalpy change for the
solution. State any assumptions made.
AH = m x c x AT ; (1) n(NaOH) = m | M = 1.00 g 40.00 gmol-1 = 0.0250 mol ; (1)
n ( limiting reagent)
= 100g x 4.18 J g-1 K-1 x (22.66 20.00 K)
0.0250 mol
= 1111.88 0.0250 Jmol-1
= 44475 Jmol-1
= - 44.5 kJmol-1 (3SF)
Assumptions
1. Specific heat capacity of the sodium hydroxide solution = specific heat
capacity of water
2. 100 g water + 1.00g NaOH = 100g solution
12 | P a g e
2. Calculate AH when 100.0 ml of 1.00 moldm-3 NaOH is added to 100.0 ml of 1.00 moldm-3
HCl in an insulated container the temperature rises from 21.0C to 34.6C.
NaOH(aq) + HCl (aq) NaCl(aq) + H2O(l)
Actual n(NaOH) = c x v = 1.00 x 100.0 1000 = 0.10 mol
Actual n(HCl) = c x v = 1.00 x 100.0 1000 = 0.10 mol
NaOH : HCl
Mole ratio from equation 1 : 1
Let = moles NaOH needed x : 0.10
by cross multiplying: = 0.10 mol NaOH is needed to react with 0.10 mol HCl
so both get used up
Since both reactants react in a 1:1 ratio and the number of moles of each is the
same both are
used up in the reaction and there is no limiting reagent.
AH = m x c x AT ; (1) n = c x v = 1.00moldm-3 x (100.0 ml 1000) ; (1)
n
= 200.0 g x 4.18 J g-1 K-1 x (34.6 21.0 K) ; (1)
0.100 mol
= - 114 kJmol-1 (3SF) ; (1)
Assumptions
1. Specific heat capacity of the solution = specific heat capacity of water
2. Total mass of reaction = 200 ml
3. 200 ml solution = 200g solution
13 | P a g e
5.2 Questions SELECTED ANSWERS
5. Q = m x c x T
= 250.0 g x 4.18 J g-1 C-1 x (95.0 25.0 C)
= - 73150 J
= - 73.2 kJ (3SF)
6. c = Q | (m x T)
c = 180 J | (70 g x 12.0 oC)
c = 0.20 Jg-1oC-1 (2SF)
7. The temperature released or absorbed is proportional to the number of moles of
the substance
a) Even though the volume has doubled the number of moles of acid and alkali has
remained
the same so the temperature change = 6 oC
b) When the concentration is doubled, the moles doubles, and so the temperature
change will
double 12 oC
8.
a) Q = m x c x T
= 100.g x 4.18 J g-1 C-1 x (19.0 14.5 C)
assume m is mass of aqueous reactant
= + 1881 J
= + 1.88 kJ (3SF)
endothermic sign is positive
b) Since the enthalpy change is proportional to the number of moles, there would
be a greater
temperature change. By increasing the moles of ammonium nitrate more heat energy
will be
absorbed by the ammonium nitrate.
9. Q = m x c x T
= 500.0 g x 4.18 J g-1 C-1 x (86.5 19.0 C)
= - 141075 J
heat released, exothermic, sign is negative
= - 141 kJ for a 10.0 g sample of chocolate
= - 141 x 5 = - 705 kJ (3 SF) for a 50.0 g chocolate bar
14 | P a g e
10.
a) Q(pot) = m x c x T
= 100.0 1000 kg x 875 kJ kg-1 C-1 x (100.0 20.0C)
= - 7.00 x 103 kJ (3SF)
heat released, exothermic, sign is negative
b) Q(water) = m x c x T
= 500.0 g x 4.18 J g-1 C-1 x (80.0C)
= - 167200 J heat released, exothermic, sign is negative
= - 167 kJ
c) n (butane) = m M
= 14.5 g 58.14 gmol-1
= 0.249 mol (3SF)
-1 (SF) once - 1 (U) once
12. N2(g) + 3H2(g) 2NH3(g) AH = - 92.0 kJ mol-1
Set up ratios and cross multiply
a) The reaction says:
1 mole N2 = - 92.0 kJ mol-1
2 mol N2 = - 92.0 x 2 = - 184 kJ mol-1
b) 2 mole NH3 = - 92.0 kJ mol-1
0.50 mole NH3 = - 92.0 x 0.50 = - 23 kJ mol-1
2
c) 1 mole N2 = - 92.0 kJ mol-1
x mol N2 = - 1840 kJ mol-1 cross multiply
20.0 mol N2 = - 1840 kJ mol-1
15 | P a g e
d) n(H2) = m M
= 10.0 g 2.02 gmol-1
= 4.95 mol
3 mole H2 = - 92.0 kJ mol-1
4.95 mol N2 = x kJ mol-1
cross multiply
4.95 mol N2 = 92.0 x 4.95 = - 152 kJ mol-1
3
13.
a) n (ethanol) = m M
= 2.50 g 46.08 gmol-1
= 0.0542 mol (3 SF)
b) H = (Q |n )
Q = H x n
= 1350 kJmol-1 x 0.0542 mol
= - 73.2 kJ (3SF)
(or 73.2 kJ energy released)
14.
a) Q = m x c x T
= 100.0 g x 4.20 Jg-1oC-1 x 21.4oC
= 8988 J of energy released
= - 8.98 x 103 J (3SF) Reaction is Exothermic
b) M (NaOH) = 40.00 gmol-1 ;
H = (Q |n )
= 8988 J | (10.0 g | 40.00 gmol-1) ;
= ( - 35952 Jmol-1)
= - 36.0 kJmol-1 (3SF) ;
(Need minus sign for the mark; and units are not given)
16 | P a g e
c) NaOH(s) + H2O(l) _ Na+
(aq) + OH-
(aq);
d) Reason for the difference - To prevent heat loss to the surrounding (thus
lowering expected
value of H);
Improvement - Use a Styrofoam cup or insulate (and cover) a beaker; Stir to
increase the rate of
the reaction
15. NaOH(s) + HCl(aq) _ NaCl(aq) + H2O(l);
a) Take the dilute HCl of known volume and concentration. This will be the
limiting reagent (or
equal moles).
b) Place in the calorimeter or some other insulated container like a styrofoam
cup.
c) Record the initial temperature in C of the HCl.
d) Take an excess (or equal) mole of the aqueous NaOH of known volume and
concentration.
Record its initial temperature in C.
e) Quickly add the NaOH to the calorimeter, cover and stir rapidly to minimize
heat loss.
f) Record the temperature change over time.
g) Determine the maximum temperature in C. [any 5 = 5 points]
Calculate enthalpy change, H using the number of moles of limiting reagent and
the
equation H = (m x c x T) nNaOH ; [1]
16.
a) KOH(aq) + HCl(aq) _ KCl(aq) + H2O(l) [1]
b) Exothermic because the temperature increases / heat is released [1]
c) To make heat loss as small as possible / so that all the heat is given out
rapidly.
(do not accept to produce a faster reaction) [1]
d) Q = m x c x T
= 100.0 g x 4.18 Jg-1oC-1 x 3.5oC [1]
= 1463 J
= - 1.46 kJ
or 1.46 kJ of energy is released
n (KOH) used = c x v (no excess or limiting reagent)
= 0.500 x 50.0
= 0.0250 mol
17 | P a g e
H = (Q |n )
= 1.46 kJ | 0.025 mol ;
= - 58.5 kJmol-1 (3SF) ; (minus needed for the mark)
e) Since the number of moles of each reactant is the same and both are used up in
the reaction
(there is no limiting reagent) doubling the concentration of HCl would not change
the
temperature because it would become the excess reagent and KOH the limiting
reagent.
17.
a) 2 NaOH(aq) + H2SO4 (aq) _ Na2SO4 (aq) + 2 H2O(l)
b)
labeled x axis with variable and unit;
descriptive title;
correctly plotted points and straight line through points;
suitable scale / good shape / good size ; [5]
c) extrapolate each best fit straight line to get maximum temperature change
until both lines
intersect; [1]
allow 10.0 to 10.2 C ; [1]
d) volume of NaOH = 39 41 cm3 [1]
18 | P a g e
moles NaOH = c x v = 1.25 x (39 1000) = 0.04875 mol ; [1]
mole H2SO4 = c x v = 1.25 x [(60 39)1000] = 0.02625 mol ; [1]
volume H2SO4 = n c = 0.0265 1.25 = 0.020 dm3 = 20. cm3 [1]
n(H2SO4)required
NaOH : H2SO4
Mole ratio from equation 2 : 1
Let = moles HCl required 0.04875 mol : mol
by cross multiplying:
2 = 0.04875 mol
= 0.024 mol H2SO4 required
n(NaOH) required
NaOH : H2SO4
Mole ratio from equation 2 : 1
Let = moles KOH required : 0.02625 mol
by cross multiplying:
= 0.02625 x 2 mol
= 0.0525 mol KOH is required
If the: actual moles of reactant < moles needed then this is the limiting
reactant
0.026 moles H2SO4 available > 0.024 moles H2SO4 required to react with all of the
NaOH it is the
excess reactant.
0.049 moles NaOH available < 0.0525 moles NaOH is the limiting reactant. [1]
e) Q = m x c x T
19 | P a g e
= 60.0 g x 4.18 Jg-1oC-1 x (10.2 2.2) oC ; [1]
= 2558 J (2.56 kJ) of energy released (accept - 2558 J) [1]
f) H = (Q |n )
= 2.56 kJ | mol limiting reagent; [1]
= 2.56 J 0.04875 mol
= - 52 kJmol-1 / - 52 kJmol-1 ; (2SF) [1]
g) % Difference = (55.5 52) 55.5 x 100 = 6.0 % ; [1]
source of error is heat loss to the surroundings ; [1]
ensure reaction vessel is well insulated and has a lid (Styrofoam) ; [1]
(the reaction takes place in a glass beaker without a lid. You need to insulate the beaker
with Styrofoam and use a lid)