Scribd
Upload
1K views

Plate Girder Design (Strength and Deflections) : 9.1. Static Analysis

The document discusses the design of a steel plate girder. It describes checking the girder's strength at critical points on the cross-section under bending moment, shear force, and combined stresses. This includes checking the normal and shear stresses, as well as welds between the web and flange. The document also addresses checking the girder's deflection to ensure it does not exceed allowable limits.

Uploaded by

Anonymous b9fkTYfEoR
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Plate Girder Design (Strength and Deflections) : 9.1. Static Analysis

The document discusses the design of a steel plate girder. It describes checking the girder's strength at critical points on the cross-section under bending moment, shear force, and combined stresses. This includes checking the normal and shear stresses, as well as welds between the web and flange. The document also addresses checking the girder's deflection to ensure it does not exceed allowable limits.

Uploaded by

Anonymous b9fkTYfEoR
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Steel Structures I.

Project

9. Plate girder design (strength and deflections)

9.1. Static analysis

Static analysis of the plate girder is


described in section 8.2.
The plate girder has to be checked for
stresses arising from bending moment
(maximum at the mid span) and shear
forces (maximum at the supports). The
combined effect of normal stresses from
bending and shear stresses (including
the effect of concentrated loading at the
top flange) has to be checked (point A).

9.2. ULS check: strength

9.2.1. Checking points on the cross-section


In a cross-section where both bending moment and shear force are present (e.g. point A on the
girder), the state of normal (σ) and shear (τ) stresses is shown in the figure below. At the extreme
fibre (point 1), the normal stress σ is maximum, while shear stress τ is equal to zero. At the
connection between web and flange (point 2), both normal and shear stresses are present. For the
sake of simplicity shear stresses are considered acting on the web only, with a constant
distribution.

σ1 σ τ1

σ τ τ τ

σ τ τ

35
Steel Structures I. Project
9.2.2. Geometric characteristics of the cross-section

Moment of inertia of the cross-section can be


determined using an engineering approach as:
b f ⋅ h3 hw3
Ix = − ( b f − tw )
12 12
Elastic section moduli at points 1 and 2 are:
Ix
Wx1 =
y1

Ix
Wx2 =
y2

9.2.3. Bending moment (normal stresses)

The general relationship for checking normal stresses under bending section 7.1.1
moment is: STAS 10108/0-78
M eq. (7.1)
σ= ≤R STAS 10108/0-78
Wn
In the case of this particular situation, this relationship can be written as:
M max
σ max = σ 1 = ≤R
Wx1

9.2.4. Shear force (shear stresses)

In the case of double T cross-sections, the following engineering section 7.1.1


approximation for checking shear stresses can be used: STAS 10108/0-78
T eq. (7.3)
τ= ≤ R f ( = 0.6 ⋅ R ) STAS 10108/0-78
hw ⋅ tw
In the case of this particular situation, this relationship can be written as:
Tmax
τ max = ≤ Rf
hw ⋅ tw

9.2.5. Combined bending and shear (equivalent stress)

In the point A along the plate girder, the cross section shall be checked
under the combined effect of bending moment, shear force and
concentrated force P. The following stresses are computed in point 2 of
the cross-section:
ƒ Normal stress from bending moment MA:
MA
σ2 = ≤R
Wx2
ƒ Shear stresses from the shear force TA:
TA
τ2 = ≤ Rf
hw ⋅ tw

36
Steel Structures I. Project
ƒ When stiffeners are not present under the concentrated force P, local
section 7.1.2
stresses σl from the concentrated force P are present as well: STAS 10108/0-78
P
σl = ≤R eq. (7.4)
z ⋅ tw STAS 10108/0-78
where
z = b "+ 2 ⋅ t f

σl

section 7.1.3
At the connection between the web and top flange of the plate girder, the STAS 10108/0-78
following check shall be performed:
eq. (7.5)
σ = σ + σ − σ ⋅ σ + 3τ ≤ 1.1R
ech
2 2
l
2
l
STAS 10108/0-78

9.3. Check of welds between the web and flange

Welds between the web and flanges of the plate girder are realised using section 17
fillet welds. Chose a weld throat thickness a to comply with the minimum STAS 10108/0-78
and maximum weld throat thickness using indications from section 5.1 in
this document.
When concentrated forces are present at the top chord, and no
transversal stiffeners are provided, the weld between the web and the
flange is checked using the following relationship:
eq. (17.2)
τ ech = τ 12 + τ 22 ≤ R sf STAS 10108/0-78
where:
τ1 is the shear stress at the web-flange interface produced by plate girder
bending
τ2 is the shear stress at the web-flange interface produced concentrated
force P
Rfs is the design shear strength of fillet weld
(Rfs =0.7R), see Table 10 STAS 10108/0-78

τ1
τ τ

37
Steel Structures I. Project

The following relationships are used to determine τ1 and τ2:


T eq. (17.1)
τ1 = STAS 10108/0-78
2 ⋅ a ⋅ hw
P
τ2 = section 17.1.b
2⋅a ⋅ z STAS 10108/0-78
where:
T - the maximum shear force along the girder
a - weld throat thickness
z - determined according to 9.2.5 in this document

9.4. SLS check: deflections

Allowable deflection of the plate girder: fa = L/400 Table 15


STAS 10108/0-78
The following relation shall be fulfilled:
f ≤ fa
where f is the deflection of the plate girder (determined with final
dimensions of the cross-section from strength checks, using loads from
the SLS combination).
The deflection f can be determined using standard methods of statics, a
computer program, or the following relationships (accounting for
deflection due to bending only):
f = f1 + f 2

5 q SLS ⋅ L4
f1 = ⋅
384 E ⋅ I x
SLS
5 M max ⋅ L2
f2 = ⋅
48 E ⋅ I x
where:
f1 - deflection due to uniformly distributed self-weight, at the serviceability
limit state [SLS] (nominal values)
f2 - deflection due to concentrated forces P, at the serviceability limit
state [SLS] (nominal values)

38

You might also like