241495534.xls.

ms_office 8/17/2014 2:01 PM 1/10

END PLATE CONNECTION DESIGN Job Name :
Calcs by : Revision No. Filename :
End Plate Connection - Moment Connection Design -4 Bolts
c. Design Nominal Reactions
Compression F
x
= 0.00 KN ; Check Staad Output
Tension F
x
= 23.00 KN ; Check Staad Output
Shear Force F
y
= 20.00 KN ; Check Staad Output
Shear Force Fz = 2.00 KN ; Check Staad Output
Bending moment Mz = 20.00 K-m ; Check Staad Output
Bending moment My = 3.00 K-m ; Check Staad Output
Supporting Member :
Beam Properties
Beam Section : = UC 203X203
Depth of column or plate D = 203.2 mm
Width of column flange or plate Bp = 203.60 mm
Web thickness of column or stiffener tc = 7.20 mm
Flange thickness of column or plate tf = 11.00 mm
Root radius of column or weld to plate r = 10.20 mm
and stiffener
Supported Member
Column Section = UC 203X203
Depth of column or plate D = 203.2 mm
Width of column flange or plate Bp = 203.60 mm
Web thickness of column or stiffener tc = 7.20 mm
Flange thickness of column or plate tf = 11.00 mm
Root radius of column or weld to plate r = 10.20 mm
and stiffener
Dimensions of the End Plate :
Length of the End Plate = 300.00 mm
Width of the End Plate = 204.00 mm
Thickness Provided, tp = 20.00 mm
Connection Details
Assumed bolt configuration
Grade of Bolts (8.8 / HSFG) = HSFG Part - 1Bolts
No. of bolt rows nr = 2.00
No. of bolt columns nc = 2.00
Total no. of bolts n = 4.00
Diameter of Bolt d d = 24.00 mm
Diameter of Bolt hole Dh Dh = 26.00 mm
Gross Area of Bolt , Ag Ag = 452.16 mm2
Tensile Stress area of Bolt As As = 352.91 mm2
Pitch ( Spacing between rows ) P = 80 mm
Guage ( Spacing between columns ) g = 90 mm
Edge Distance ( Top ) etop = 40.00 mm
End Distance ( Bottom ) e2bottom = 40 mm
End Distance ( Side ) e' = 40.00 mm
Slip factor for untreated = 0.50
For clearance holes Ks = 1.00 T1
Least thick of plate t = 11.00 mm
a 1 = 136.10
Forces in Bolts
Tension per bolt due to Moment Mz T2
For Row 1 T1 = Mz*a1/(nc(a1+a2)
T1 = 62.80 KN a2= 56.10
For Row 2 T2 = Mz*a2/(nc(a1+a2)
T2 = 25.89 KN Assumed Rotation Point
STRUCTURAL CALCULATIONS
SAMALSADI
241495534.xls.ms_office 8/17/2014 2:01 PM 2/10
END PLATE CONNECTION DESIGN Job Name :
Calcs by : Revision No. Filename :
STRUCTURAL CALCULATIONS
SAMALSADI
Tension per bolt due to Moment My
For Column 1 T1 = My/(nr*g)
T 1 = 16.67 KN
g = 90.00
Tension per bolt due to Axial = Fx/n
tension Fx 5.75 KN Assumed Rotation Point
Maximum forces Transfer to Each Bolt
Maximum Tension in bolt row 1 = 85.22 KN
Maximum Tension in bolt row 2 = 48.30 KN
Check for Bolts :
Yield strength of bolt Yf = 882.00 N/mm2
Ult. Tensile strength of bolt Uf = 981.00 N/mm2
Shear stress of bolt Ps = 400.00 N/mm2
Tension stress of bolt Pt = 700.00 N/mm2
Bearing stress of bolt Pbb = 1,300.00 N/mm2
Minimum proof stress P0 = 776.00 N/mm2
of bolt
Minimum shank tension P0 = 232.70 KN
in HSFG bolts
Capacity of one bolt
Shear capacity of bolt Ps = 141.16 KN
Bearing capacity of bolt Pb = 346.67 KN
Tension capacity of bolt Pt' = 209.43 KN 0.9*P0
Slip resistance of one bolt PsL = 0.9 * Ks * * P0
= 104.72 KN
Design strength of steel py = 345.00 N/mm2
Bearing strength of steel pb = 825.00 N/mm2
Design strength of weld pw = 220.00 N/mm2
Connection Geometry
Column Side
m1 = g/2 - tc/2 - 0.8rc m2 = (dc-P)/2 40.40 mm
= 33.24 mm
e = B/2-g/2
= 56.80 mm
For n smallest of n = 41.55 mm
e for the column flange = 56.80 mm
e for the end plate = 56.80 mm
1.25 m for column flange= 41.55 mm
Beam
m = g/2 - tc/2 - 0.8rc
= 36.60 mm Leg length of fillet weld to beam web, Sww =
e = B/2-g/2 6.00
= 56.80 mm
For n smallest of n = 45.75 mm
e for the column flange = 56.80 mm
e for the end plate = 56.80 mm
241495534.xls.ms_office 8/17/2014 2:01 PM 3/10
END PLATE CONNECTION DESIGN Job Name :
Calcs by : Revision No. Filename :
STRUCTURAL CALCULATIONS
SAMALSADI
1.25 m for column flange= 45.75 mm
Potential Resistance of Bolts in Tension Zone
Bolt Row 1 & 3
Bolt Row 1 & 3 alone
Column Flange Bending
Calculate effective length of T-stub as per Table2.2 of SCI
For bolt row below the flange of a flush end plate
Leff = Min of [ Max{ii,iii}, i ]
Ref. Table 2.2 of moment connection by BCSA
Leff for i = 2 m 208.75 mm
Leff for ii = 4m+1.25e 203.96 mm
Leff iii = m1 1 = m1/(m1+e) 1 = 0.39
2 = m2/(m1+e) 2 = 0.45
where from Fig 2.16 = 6.00
Leff iii = 199.44 mm
Ledd = min of ( max(i,iii),ii) 203.96 mm
Plastic moment capacity of the Mp = Leff x tf x py/4
equivalent T-stub = 2.13 KN.m
Potential resistance is the minimum of the following
Mode 1 Complete flange yielding Pr = 4 Mp / m 256.15 KN
Mode 2 Bolt failure with flange Pr = (2 Mp + n( Pt'))/(m+n)
yielding = 289.62 KN
Mode 3 Bolt failure Pr = Pt'
418.86 KN
Potential resistance for column flange bending Pr = 256.15 KN
Column Web Tension
As row 1 & 3 is near the flange, web tension can be discounted
End Plate Bending
Calculate effective length of T-stub as per Table2.5 of SCI
For bolt row below the flange of a flush end plate
Leff = Min of [ Max{ii,iii}, i ]
Ref. Table 2.4 of moment connection by BCSA
Leff for i = 2 m 229.85 mm
Leff for ii = 4 m + 1.25 e 217.40 mm
Leff iii = m1 1 = m1/(m1+e) 1 = 0.39
2 = m2/(m1+e) 2 = 0.43
where from Fig 2.16 = 6.00
Leff iii = 219.60 mm
Plastic moment capacity of the Mp = Leff x tf x py/4
equivalent T-stub = 7.58 KN.m
Potential resistance is the minimum of the following
241495534.xls.ms_office 8/17/2014 2:01 PM 4/10
END PLATE CONNECTION DESIGN Job Name :
Calcs by : Revision No. Filename :
STRUCTURAL CALCULATIONS
SAMALSADI
Mode 1 Complete flange yielding Pr = 4 Mp / m 828.00 KN
Mode 2 Bolt failure with flange Pr = (2 Mp + n( Pt'))/(m+n)
yielding = 416.70 KN
Mode 3 Bolt failure Pr = Pt'
418.86 KN
Potential resistance for column flange bending Pr = 416.70 KN
Beam Web Tension
As row 1 & 3 is near the flange, web tension can be discounted
Bolt Row 2
Row 2 and 1 as group
Column Flange Bending
Calculate effective length of T-stub as per Table2.6 of SCI
Leff = { Max of [ ii/2,(iii-ii/2)] }x2 + p 283.96 mm
Plastic moment capacity of the Mp = Leff x tf x py/4
equivalent T-stub = 2.96 KN.m
Potential resistance is the minimum of the following
Mode 1 Complete flange yielding Pr = 4 Mp / m 356.62 KN
Mode 2 Bolt failure with flange Pr = (2 Mp + n( Pt'))/(m+n)
yielding = 544.65 KN
Mode 3 Bolt failure Pr = Pt'
837.72 KN
Potential resistance for column flange bending Pr = 356.62 KN
Column Web Tension
Web tension can be discounted due to effective tensile length of web assuming a max. spread at
60deg from bolts to the centre of web is crossing the flange.
End Plate Bending
Calculate effective length of T-stub as per Table2.5 of SCI
Leff = { Max of [ ii/2,(iii-ii/2)] }x2 + p 301.80 mm
Plastic moment capacity of the Mp = Leff x tp x py/4
equivalent T-stub = 10.41 KN.m
Potential resistance is the minimum of the following
Mode 1 Complete flange yielding Pr = 4 Mp / m 1,137.93 KN
Mode 2 Bolt failure with flange Pr = (2 Mp + n( Pt'))/(m+n)
yielding = 718.27 KN
241495534.xls.ms_office 8/17/2014 2:01 PM 5/10
END PLATE CONNECTION DESIGN Job Name :
Calcs by : Revision No. Filename :
STRUCTURAL CALCULATIONS
SAMALSADI
Mode 3 Bolt failure Pr = Pt'
837.72 KN
Potential resistance for column flange bending Pr = 718.27 KN
Beam Web Tension
Web tension can be discounted due to effective tensile length of web assuming a max. spread at
60deg from bolts to the centre of web is crossing the flange
Potential Resistance of Bolts in Tension Zone
WORK SHEET: TENSION ZONE
Step 1 Column Side
Beam
Side
Row
Flange
Bending
Web Tension
Flange
Bending
Web
Tension
Potential
Resistance
1.00 Resistance of Row 1 256.15
256.15 N.A 416.70 N.A
2.00
Resistance of
Row 2 only
100.47
256.15 N.A 416.70 N.A
Resistance of
Row 2+1 as
group
356.62 N.A 718.27 N.A
100.47 301.57
Pr1 = Capacity of row 1 alone
Pr2 = Min. of { Capacity of row 2 alone,
( Capacity of row 2+1 ) - Pr1 }
241495534.xls.ms_office 8/17/2014 2:01 PM 6/10
; Check Staad Output
; Check Staad Output
; Check Staad Output
; Check Staad Output
; Check Staad Output
; Check Staad Output
STRUCTURAL CALCULATIONS
241495534.xls.ms_office 8/17/2014 2:01 PM 7/10
STRUCTURAL CALCULATIONS
mm
241495534.xls.ms_office 8/17/2014 2:01 PM 8/10
STRUCTURAL CALCULATIONS
241495534.xls.ms_office 8/17/2014 2:01 PM 9/10
STRUCTURAL CALCULATIONS
241495534.xls.ms_office 8/17/2014 2:01 PM 10/10
STRUCTURAL CALCULATIONS