International Journal of Technical Research and Applications e-ISSN:

2320-8163, www.ijtra.com Volume 1, Issue 1 (july-aug 2013), PP. 01-08

1 | P a g e
INVESTIGATION OF THE EFFECT OF
CURRENT ON TENSILE STRENGTH AND
NUGGET DIAMETER OF SPOT WELDS MADE
ON AISI-1008 STEEL SHEETS
A K PANDEY, M. I. KHAN, K. M. MOEED
Department of Mechanical Engineering
Integral University,Lucknow, India.
AbstractThe results of the investigation indicate the welding
current to be the most significant parameter controlling the weld
tensile strength as well as the nugget diameter. The contribution
of welding current holding time and pressure to tensile strength
are 61%, 29%, 4% respectively and the contribution of these
parameters to nugget diameter are 81%, 17%, 1.7% respectively.
Relationship graph have been plotted between tensile strength
and nugget diameter with parametric variations according to
orthogonal array
Keywords resistance spot welding, taguchi method, tensile
strength, nugget diameter, annova etc
I. INTRODUCTION
Resistance spot welding (RSW) is a major sheet metal joining
process in many industries, such as the automobile, domestic
appliances, air craft and space craft fabrications. It is an efficient
joining process widely used for the fabrication of sheet metal
assemblies. There are 3000-6000 spot welds in any car, which shows
the level importance of the resistance spot welding. RSW has
excellent techno-economic benefits such as low cost, high production
rate and adaptability for automation which make it an attractive
choice for auto-body assemblies, truck cabins, rail vehicles and home
appliances. [1] It is one of the oldest of the electric welding processes
in use by industry today. Furthermore, other metal-to-metal
connections, such as wire-to-wire joints in the electronics industry,
are accomplished by resistance spot welding. Application-specific
measures, such as the diameter of the welding spot, determine the
quality of the joint. The weld is made by a combination of heat,
pressure, and time. As the name implies, it uses the resistance of the
materials to the flow of current that causes localized heating between
the part to be joined. Understanding of physical mechanisms for
easily manipulating and controlling weld qualities in advance is
important.[2]
II. TAGUCHI METHOD
It is a powerful tool for the design of high quality systems. It
provides simple, efficient and systematic approach to optimize
designs for performance, quality and cost [3]. Taguchi method can
be efficiently used for designing a system that operates
consistently and optimally over a variety of conditions. To
determine the best design it requires the use of strategically
designed experiments. Taguchi approach to design of experiments
is easy to adopt and apply for users with limited knowledge of
statistics; hence it has gained wide popularity in the engineering
and scientific community [4-5]. The desired welding parameters
are determined based on experience & books.
Steps of Taguchi method are as follows:
1. Identification of the main function, to be optimized
and its side effects and failure mode.
2. Identification of noise factors, testing conditions and
quality characteristics.
3. Identification of the main function to be optimized.
4. Identification the control factors and their levels.
5. Selection of orthogonal array and matrix experiment.
6. Conducting the matrix experiment.
7. Analyzing the data and prediction of the optimum
level.
8. Determining the contribution of the parameters on the
performance.
9. Performing the verification experiment and planning
the future action. [6]
This study is an experimental design process called the
Taguchi design method. Taguchi design, developed by Dr.
Genichi Taguchi, is a set of methodologies by which the
inherent variability of materials and manufacturing processes
can be taken into account at the design stage [7]. Although
similar to design of experiment (DOE), the Taguchi design
only conducts the balanced (orthogonal) experimental
combinations, which makes the Taguchi design even more
effective than a fractional factorial design. By using the
Taguchi techniques, industries are able to greatly reduce
product development cycle time for both design and
production, therefore saving costs and increasing profit.
Taguchi proposed that engineering optimization of a process
or product should be carried out in a three-step approach:
system design, parameter design, and tolerance design. In
system design, the engineer applies scientific and engineering
knowledge to produce a basic functional prototype design.
International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 1, Issue 2 (july-aug 2013), PP. 01-08

2 | P a g e

The objective of the design [8] is to optimize the settings of
the process parameter values for improving performance
characteristics and to identify the product parameter values
using the optimal process parameters.
The parameter design is the key step in the Taguchi method
for achieving high quality without increasing cost. The steps
included in the Taguchi parameter design are: selecting the
proper orthogonal array (OA) according to the numbers of
controllable factors (parameters); running experiments based
on the OA; analyzing data; identifying the optimum
conditions; and conducting confirmation runs using the
optimal levels of the parameters. The main effects indicate the
general trend of influence of each parameter. Knowledge of
the contribution of individual parameters is the key for
deciding the nature of the control to be exercised on a
production process.[9]
Analysis of variance (ANOVA) is the statistical treatment
most commonly applied to the results of the experiments to
determine the percentage contribution of each parameter
against a stated level of confidence [10]. Taguchi suggests two
different routes for carrying out the complete analysis. In the
standard approach the results of a single run or the average of
the repetitive runs are processed through the main effect and
ANOVA . The second approach, which Taguchi strongly
recommends for multiple runs, is to use the signal-to-noise
(S/N) ratio for the same steps in the analysis.[11]

III. RESISTANCE WELDING PARAMETERS

There are three main parameters which control the quality of
resistance spot welding. Diagrammatically shown in figure:

Figure.1 Cause and effect diagram of main welding
parameters

A. Effect of Welding Current
Current controls the heat which generated according to the
equation Q = I2Rt.this shows that the current has more
influence on the amount of heat generated
Tensile shear strength increases rapidly with increasing
current density. Excessive current density will cause molten
metal expulsion (resulting in internal voids), weld cracking,
and lower mechanical strength properties. Typical variations in
shear strength of spot welds as a function of current magnitude
are shown in Figure 2. In the case of spot welding excessive
current will overheat the base metal and result in deep
indentations in the parts and, it will cause overheating and
rapid deterioration of the electrodes.


Figure.2 Effect of welding current on shear strength

B. Effect of Weld Time
The rate of heat generation must be such that welds with
adequate strength will be produced without excessive electrode
heating and rapid deterioration. The total heat developed is
proportional to weld time. During a spot welding operation,
some minimum time is required to reach melting temperature
at some suitable current density. Excessively long weld time
will have the same effect as excessive amperage on the base
metal and electrodes. Furthermore, the weld heat-affected zone
will extend farther into the base metal.
The relationship between weld time and spot weld shear
strength is shown in Figure.3 assuming all other conditions
remain constant. To a certain extent, weld time and amperage
may be complementary. The total heat may be changed by
adjusting either the amperage or the weld time. Heat transfer is
a function of time and the development of the proper nugget
size requires a minimum length of time, regardless of
amperage

Figure.3 Tensile-shear strength as a function of weld time

C. Effect of Welding Pressure
Welding pressure is produced by the force exerted on the joint
by the electrodes. Electrode force is considered to be the net
dynamic force of the electrodes upon the work, and it is the
resultant pressure produced by this force that affects the
International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 1, Issue 2 (july-aug 2013), PP. 01-08

3 | P a g e

contact resistance. As the pressure is increased, the contact
resistance and the heat generated at the interface will decrease.
To increase the heat to the previous level, amperage or weld
time must be increased to compensate for the reduced
resistance. The surfaces of metal components, on a
microscopic scale, are a series of peaks and valleys. When
they are subjected to light pressure, the actual metal-to-metal
contact will be only at the contacting peaks, a small
percentage of the area. Contact resistance will be high. As the
pressure is increased, the high spots are depressed and the
actual metal-to-metal contact area is increased, thus
decreasing the contact resistance. [12]

IV. WELD QUALITY ATTRIBUTES
The quality of a weld is usually expressed by its measurable
features, such as the physical attributes and the various
strengths, when inspected in either a destructive or
nondestructive manner. A welds quality can be described in
three ways: by its physical or geometric features, its strength
or performance, or the process characteristics during welding.
The geometric features are either directly visible after a
weldment is made or revealed through destructive tests, such
as peeling or cross-sectioning or seeing the microstructures, or
nondestructive tests using, for example, ultrasonic or x-ray
devices.
The commonly used weld attributes are:
Nugget/button size
Penetration
Indentation
Cracks (surface and internal)
Porosity/voids
Sheet separation
Surface appearance
Among these weld attributes, weld size, in terms of nugget
width or weld button diameter, is the most frequently
measured and most meaningful in determining a welds
strength. When two sheets are joined by a weld at the nugget,
its size determines the area of fusion and its load-bearing
capability. However, the nugget/weld size alone is often
insufficient in describing a welds quality, as it does not
necessarily imply the structural integrity of the weld. Other
features of a weld, such as penetration, may complement the
nugget size and provide useful information on the degree of
adhesion. Weld and nugget are considered interchangeability
by many, especially in oral presentations. Although closely
related, however, they are not the same by definition or
measurement. In fact, a weld is meant to contain all parts of a
weldment, such as the heat-affected zone (HAZ), in addition
to the nugget. Confusion is also in the use of button diameter
or nugget diameter. As a nugget and its size are usually
revealed by cross sectioning for metallo graphic examination,
a nugget is exposed for measuring its width, not diameter, as
shown in Figure 1 The figure also shows other features that
can be revealed by cross-sectioning a weldment.[13]






Figure.4 Weld attributes revealed by metallographic
sectioning

V. METHOD OF EXPERIMENT
The three main parameters in spot welding are current, contact
resistance and weld time. In order to produce good quality
weld the above parameters must be controlled properly. The
amount of heat generated in this process is governed by the
formula: Q = I
2
R T
Where Q = heat generated, Joules
I = current, Amperes
R = resistance of the work piece, Ohms
T = time of current flow, second
A. Selection Of Metal
Firstly I will select the metal to be weld according desire
weldability which must rely on basic properties of the
material, such as strength, corrosion or erosion resistance,
ductility, and toughness. The properties of the various
metallurgical structures associated with the thermal cycles
encountered in the welding operation must also be included in
the design process.
Material Detail:
Material used is low carbon cold rolled 0.9 mm mild steel
sheets (AISI 1008/ASTM A366) with the following
composition carbon 0.08%; manganese 0.6%;phosphorus
0.35%; copper 0.2% ;sulphur 0.04% remaining iron.
B. Design The Orthogonal Array
Depending upon number of levels in a factor, a 2 or a 3 level
OA can be selected. If some factors are two-level and some
are three-level, then whichever is predominant would indicate
which kind of OA is to be selected. Once the decision is made
about the right OA, then the number of trials for that array
would provide the adequate total dof, When required dof fall
between the two dof provided by two OAs, the next larger OA
must be chosen.
International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 1, Issue 2 (july-aug 2013), PP. 01-08

4 | P a g e


Figure.5 selection of taguchi design

VI. EXPERIMENTAL PROCEDURE

The results have been recorded as shown in (Tabl1.1) and
analysis the tensile strength of the welded specimen.





Figure.6 Welded specimen







Figure.7 Tensile strength testing


Figure.8 Arrangement for microscope view and one of
microscopic image for measuring the nugget diameter

1) Analysis Of S/N Ratio Based On Taguchi Method
Taguchi recommends analyzing data using the S/N ratio that
will offer two advantages; it provides guidance for selection
the optimum level based on least variation around on the
average value, which closest to target, and also it offers
objective comparison of two sets of experimental data with
respect to deviation of the average from the target. The
experimental results are analyzed to investigate the main
effects.
According to Taguchi method, S/N ratio is the ratio of
Signal representing desirable value, i.e. mean of output
characteristics and the noise representing the undesirable
value i.e., squared deviation of the output characteristics. It is
denoted by and the unit is dB. The S/N ratio is used to
International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 1, Issue 2 (july-aug 2013), PP. 01-08

5 | P a g e

measure quality characteristic and it is also used to measure
significant welding parameters.
According to quality engineering the characteristics are
classified as Higher the best (HB) and lower the best (LB). HB
includes T-S strength and Nugget diameter which desires
higher values. Similarly LB includes Heat Affected Zone
(HAZ) for which lower value is preferred.

The summary statistics the S/N ratio (dB) is given by:


Larger the best performance



Lower the best performance


TABLE 1 Process parameters with their values at three levels
Levels Current
(KA)
ELECTRODE
FORCE(KN)
Time
(SEC)
1 6.0 0.662 2
2 6.8 0.789 4
3 7.5 0.968 5


TABLE 2 Experimental data for tensile shear (T-S) strength
and S/N ratio
C

P T

T-S
(KN)
Nugget
Dia. (m)
S/N
Ratio.1
S/N
Ratio.2
1 1 1 2.82 6800 9.0050 76.6502
1 2 2 3.10 7000 9.8272 77.0252
1 3 3 3.54 7210 10.9801 77.2783
2 1 2 4.23 7500 12.5268 77.5012
2 2 3 4.55 7700 13.1602 77.7298
2 3 1 3.54 7800 10.9801 77.9525
3 1 3 4.33 7900 12.7298 78.0618
3 2 1 3.94 8200 11.9099 78.1697
3 3 2 3.58 8620 11.0777 78.8103
Where C is current P is pressure and T is time.

7.5 6.8 6.0
12.0
11.5
11.0
10.5
10.0
0.968 0.789 0.662
5 4 2
12.0
11.5
11.0
10.5
10.0
CURRENT
M
e
a
n

o
f

S
N

r
a
t
i
o
s
PRESSURE
TIME
Main Effects Plot for SN ratios
Data Means
Signal-to-noise: Larger is better
Figure.9 Main Effect Plot For S/N Ratio (Tensile Strength)
7.5 6.8 6.0
78.5
78.0
77.5
77.0
0.968 0.789 0.662
5 4 2
78.5
78.0
77.5
77.0
CURRENT
M
e
a
n

o
f

S
N

r
a
t
i
o
s
PRESSURE
TIME
Main Effects Plot for SN ratios
Data Means
Signal-to-noise: Larger is better
Figure.10 Main Effect Plot For S/N Ratio (nugget diameter)


TABLE 3 Response table for S/N ratio for T-S strength
Level Current Pressure Weld time
1 9.937 11.421 10.632
2 12.222 11.632 11.144
3 11.906 11.013 12.290
Delta 2.285 0.620 1.658
Rank 1 3 2

TABLE 4 Response table for S/N ratio for nugget diameter

Level Current Pressure Weld time
1 76.98 77.40 77.59
2 77.73 77.64 77.78
3 78.35 77.01 77.69
Delta 1.36 0.61 0.19
Rank 1 2 3



International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 1, Issue 2 (july-aug 2013), PP. 01-08

6 | P a g e

VII. ANALYSIS OF VARIANCE (ANOVA)

ANOVA is a statistically based, objective decision-making
tool for detecting any differences in the average performance
of groups of items tested. ANOVA helps in formally testing
the significance of all main factors and their interactions by
comparing the mean square against an estimate of the
experimental errors at specific confidence levels.

TABLE-5 Analysis of Variance for SN ratios(tensile strength)

CF DOF SS MS F
RATIO
P % C
Current 2 9.1956 4.5978 9.92 0.092 61.11
Pressure 2 0.5956 0.2978 0.64 0.609 3.96
Time 2 4.3261 2.1631 4.67 0.177 28.76
ERROR 2 0.9273 0.4637
TOTAL 8 15.0446

R-Sq = 95.3% R-Sq(adj) = 81.1%;Significant at 95%
confidence

TABLE-6 Analysis of Variance for SN ratios(nugget
diameter)
CF DOF SS MS F
ratio
P % C
Current 2 2173622 1153144 128.2 0.008 80.82
Pressure 2 453089 147878 26.72 0.097 16.85
Time 2 45622 19144 2.69 0.452 1.70
ERROR 2 16956 8478
TOTAL 8 2689289

R-Sq = 95.3% R-Sq(adj) = 81.1%;Significant at 95%
confidence

VIII. CONCLUSION

The following conclusions could be drawn from the above
investigation:
1. The response of S/N ratio with respect to tensile
strength indicates the welding current to be the
most significant parameter that controls the weld
tensile strength wheres the holding time and
pressure are comparatively less significant in this
regard.
2. The contribution of welding current holding time
and pressure towards tensile strength is 61%,
28.7%and 4% respectively as determined by the
ANOVA method for tensile strength
3. Optimum results have been obtain by taguchi
method using medium current of 6.8 KA, medium
pressure of 0.79KPa and high holding time of 5
seconds.

4. The response of S/N ratio with respect to nugget
diameter also indicates the welding current to be
the most significant parameter that controls the
nugget diameter wheres the pressure and welding
time are comparatively less significant in this
regard.
5. The contribution of welding current welding time
and pressure towards nugget diameter is 80.82,
16.85 and 1.70respectively as determined by the
ANOVA method
CURRENT
PRESSURE
WELD
TIME

Figure.11 Contribution Pi Diagram

6. It follows the 80-20 rule of pareto principle. The
current contributes 80% the formation of nugget
diameter although it is one of the important
contributing factors


Figure.12 pareto chart of contributing factors

7. Relationship graph could be ploted between the
tensile strength and nugget diameter with
parametric variations according tp orthogonal
array(figure.13)
International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 1, Issue 2 (july-aug 2013), PP. 01-08

7 | P a g e


Figure. 13 Comparision graph between tensile strength and
nugget diameter


REFERENCES

[1] Aslanlar S, Ogur A, Ozsarac U, Ilhan E. Welding time effect on
mechanical properties of automotive sheets in electrical
resistance spot welding. J MaterDes 2008;29:142731..
[2] Luo Yi , Liu Jinhe ,Xu Huibin, Xiong Chengzhi, Liu lin.
Regression modeling and process analysis of resistance spot
welding on galvanized steel sheet
[3] AWS D8.7: Recommended Practices for Automotive Weld
QualityResistance Spot Welding, American Welding Society,
Miami, FL, 2004.
[4] W.H. Yang, Y.S. Tang, Design optimization of cutting
parameters for turning operations based on Taguchi method,
Journal of Materials Processing Technology, 84 (1998) 122-129.
[5] D.C. Montgometry, Design and analysis of experiments, 4th
edition, New York: Wiley; 1997.
[6] N. Nalbant, H. Gokkaya, G. Sur, Application of Taguchi method
in the optimization of cutting parameters for surface roughness
in turning, Materials and Design, date received
[7] Onkar N. Panday Total Quality Management
[8] G.S. Peace, Taguchi Methods, A Hands-on Approach, Addision-
Wesley, MA, 1992.
[9] Ross, P.J., Taguchi Technique for Quality Engineering, 1988
(McGraw-Hill: New York).
[10] Roy, R.K., A Primer on the Taguchi Method, 1990 (Van
Nostrand Reinhold: New York).
[11] K. S. Yeung, and P.H. Thornton, Transient Thermal Analysis
of Spot Welding Electrodes, Welding Research, January,
(1999), pp. 16.
[12] M. Jou, Experimental Investigation of Resistance Spot Welding
for Sheet Metals Used in Automotive Industry, JSME I.J.
Series C-Mechanical Systems Machine Elements and
Manufacturing, 2(2001), pp. 544552.
[13] Welding Handbook Volume 2 8th Edition, Welding Processes,
Part 1 p 534-535
[14] J.f. Young and R.S. Shane, Ed., Materials And Processes, Part
B: Processes, 3rd Ed.,Marcel dekker, 1985, p 11257-1126
[15] J.g. Bralla, ed., Handbook Of Product Design For
Manufacturing, McGraw-Hill, 1986, p 7-35
[16] Ewing, K. W., Cheresh, M., Thompson, R., and Kukuchek, P.,
1982, Static and Impact Strengths of Spot-Welded HSLA and
Low Carbon Steel Joints, SAE Paper 820281.
[17] VandenBossche, D. J., 1977, Ultimate Strength and Failure
Mode of Spot Welds in High Strength Steels, SAE paper
770214.
[18] Radaj, D., 1989, Stress Singularity, Notch Stress and
Structural Stress at Spot-Welded Joints, Eng. Fract. Mech.,
34~2!, pp. 495506.
[19] Radaj, D., and Zhang, S., 1993, On the Relations Between
Notch Stress and Crack Stress Intensity in Plane Shear and
Mixed Mode Loading, Eng. Fract. Mech., 44~5!, pp. 691704.
[20] Zhang, S., 2001, Approximate Stress Formulas for a
Multiaxial Spot Weld Specimen, Weld. J. ~Miami!, 80~8!
201s203s.
[21] Zhang, S., 1999, Approximate Stress Intensity Factors and
Notch Stresses for Common Spot-Welded Specimens,Weld. J.
~Miami!, 78~5!, pp. 17351795.
[22] Wung, P., 2001, A Force-Based Failure Criterion for Spot
Weld Design, Exp. Mech., 41~4!, pp. 107113.
[23] Wung, P., Walsh, T., Ourchane, A., Stewart, W., and Jie, M.,
2001, Failure of Spot Welds Under In-Plane Static Loading,
Exp. Mech., 41~1!, pp. 100106.
[24] Zuniga, S., and Sheppard, S. D., 1997, Resistance Spot Weld
Failure Loads and Modes in Overload Conditions, Fatigue and
Fracture Mechanics: 27th Volume, ASTM STP 1296, R. S.
Piascik, J. C. Newman, and N. E. Dowling, eds., American
Society for Testing and Materials, pp. 469489. 802.11, 1997.
[25] Barkey, M. E., and Kang, H., 1999, Testing of Spot Welded
Coupons in Combined Tension and Shear, Exp. Tech., 23~5!,
pp. 2022.
[26] Lee, Y., Wehner, T., Lu, M., Morrissett, T., Pakalnins, E., 1998,
Ultimate Strength of Resistance Spot Welds Subjected to
Combined Tension and Shear, J. Test. Eval., 26~3!, pp. 213
219.
[27] Lin, S. H., Pan, J., Wu, S., Tyan, T., and Wung, P., 2002,
Failure Loads of Spot Welds under Combined Opening and
Shear Static Loading Conditions, Int. J. Solids Struct., 39, pp.
1939.
[28] Copeland, Lee. "Object-Oriented Testing." Software Quality
Engineering. STAR East 2001. The Rosen Centre Hotel,
Orlando, Florida. 14 May 2001
[29] Sloane, Neil J. A. A Library of Orthogonal Arrays. Information
Sciences Research Center, AT&T Shannon Labs. 9 Aug. 2001
<http://www.research.att.com/~njas/oadir/>.
International Journal of Technical Research and Applications e-ISSN: 2320-8163,
www.ijtra.com Volume 1, Issue 2 (july-aug 2013), PP. 01-08

8 | P a g e

[30] Wu C.F.J., and Hamada M., Planning, Analysis and Parameter
Design Optimiza-tion, John Wiley & Sons, New York (NY),
2000.
[31] A field guid to expermintal design Washington State
University ,Tree Fruit Research and Extension Center
http://www.tfrec.wsu.edu/anova/basic.htmlp
[32] Handbook for resistance spot welding, Miller Electric Mfg. Co.
Appleton, 2010
[33] C.F. Larson, Bibliography on resistance welding 1950
1971,Welding Journal 51 (1972).
[34] ASM Metals HandBook Volume 06 - Welding, Brazing, and
SolderingScience, 1989.